From: Tedd Ho-Jeong An <[email protected]>
This patch adds support for Intel Bluetooth device by adding
btusb_setup_intel() routine that update the device with ROM patch.
T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=07dc Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Tedd Ho-Jeong An <[email protected]>
---
v7 changes:
- fixed endian swapping for opcode
- removed type casting for cmd_param in in __hci_cmd_sync_ev()
- made command param arrays to const
- minor format change
- required Johan's new patch: [PATCH] Bluetooth: Fix HCI command send functions to use const specifier
drivers/bluetooth/btusb.c | 378 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 378 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 3d684d2..6e4a764 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -23,6 +23,7 @@
#include <linux/module.h>
#include <linux/usb.h>
+#include <linux/firmware.h>
#include <net/bluetooth/bluetooth.h>
#include <net/bluetooth/hci_core.h>
@@ -47,6 +48,7 @@ static struct usb_driver btusb_driver;
#define BTUSB_BROKEN_ISOC 0x20
#define BTUSB_WRONG_SCO_MTU 0x40
#define BTUSB_ATH3012 0x80
+#define BTUSB_INTEL 0x100
static struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
@@ -207,6 +209,9 @@ static struct usb_device_id blacklist_table[] = {
/* Frontline ComProbe Bluetooth Sniffer */
{ USB_DEVICE(0x16d3, 0x0002), .driver_info = BTUSB_SNIFFER },
+ /* Intel Bluetooth device */
+ { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
+
{ } /* Terminating entry */
};
@@ -943,6 +948,376 @@ static int btusb_setup_bcm92035(struct hci_dev *hdev)
return 0;
}
+struct intel_version {
+ u8 status;
+ u8 hw_platform;
+ u8 hw_variant;
+ u8 hw_revision;
+ u8 fw_variant;
+ u8 fw_revision;
+ u8 fw_build_num;
+ u8 fw_build_ww;
+ u8 fw_build_yy;
+ u8 fw_patch_num;
+} __packed;
+
+static const struct firmware *btusb_setup_intel_get_fw(struct hci_dev *hdev,
+ struct intel_version *ver)
+{
+ const struct firmware *fw;
+ char fwname[64];
+ int ret;
+
+ snprintf(fwname, sizeof(fwname),
+ "intel/ibt-hw-%x.%x.%x-fw-%x.%x.%x.%x.%x.bseq",
+ ver->hw_platform, ver->hw_variant, ver->hw_revision,
+ ver->fw_variant, ver->fw_revision, ver->fw_build_num,
+ ver->fw_build_ww, ver->fw_build_yy);
+
+ ret = request_firmware(&fw, fwname, &hdev->dev);
+ if (ret < 0) {
+ if (ret == -EINVAL) {
+ BT_ERR("%s Intel firmware file request failed (%d)",
+ hdev->name, ret);
+ return NULL;
+ }
+
+ BT_ERR("%s failed to open Intel firmware file: %s(%d)",
+ hdev->name, fwname, ret);
+
+ /* If the correct firmware patch file is not found, use the
+ * default firmware patch file instead
+ */
+ snprintf(fwname, sizeof(fwname), "intel/ibt-hw-%x.%x.bseq",
+ ver->hw_platform, ver->hw_variant);
+ if (request_firmware(&fw, fwname, &hdev->dev) < 0) {
+ BT_ERR("%s failed to open default Intel fw file: %s",
+ hdev->name, fwname);
+ return NULL;
+ }
+ }
+
+ BT_INFO("%s: Intel Bluetooth firmware file: %s", hdev->name, fwname);
+
+ return fw;
+}
+
+static int btusb_setup_intel_patching(struct hci_dev *hdev,
+ const struct firmware *fw,
+ const u8 **fw_ptr,
+ int *disable_patch)
+{
+ struct sk_buff *skb;
+ struct hci_command_hdr *cmd;
+ const u8 *cmd_param;
+ struct hci_event_hdr *evt = NULL;
+ const u8 *evt_param = NULL;
+ int remain = fw->size - (*fw_ptr - fw->data);
+
+ /* The first byte indicates the types of the patch command or event.
+ * 0x01 means HCI command and 0x02 is HCI event. If the first bytes
+ * in the current firmware buffer doesn't start with 0x01 or
+ * the size of remain buffer is smaller than HCI command header,
+ * the firmware file is corrupted and it should stop the patching
+ * process.
+ */
+ if (remain > HCI_COMMAND_HDR_SIZE && *fw_ptr[0] != 0x01) {
+ BT_ERR("%s Intel fw corrupted: invalid cmd read", hdev->name);
+ return -EINVAL;
+ }
+ (*fw_ptr)++;
+ remain--;
+
+ cmd = (struct hci_command_hdr *)(*fw_ptr);
+ *fw_ptr += sizeof(*cmd);
+ remain -= sizeof(*cmd);
+
+ /* Ensure that the remain firmware data is long enough than the length
+ * of command parameter. If not, the firmware file is corrupted.
+ */
+ if (remain < cmd->plen) {
+ BT_ERR("%s Intel fw corrupted: invalid cmd len", hdev->name);
+ return -EFAULT;
+ }
+
+ /* If there is a command that loads a patch in the firmware
+ * file, then enable the patch upon success, otherwise just
+ * disable the manufacturer mode, for example patch activation
+ * is not required when the default firmware patch file is used
+ * because there are no patch data to load.
+ */
+ if (*disable_patch && le16_to_cpu(cmd->opcode) == 0xfc8e)
+ *disable_patch = 0;
+
+ cmd_param = *fw_ptr;
+ *fw_ptr += cmd->plen;
+ remain -= cmd->plen;
+
+ /* This reads the expected events when the above command is sent to the
+ * device. Some vendor commands expects more than one events, for
+ * example command status event followed by vendor specific event.
+ * For this case, it only keeps the last expected event. so the command
+ * can be sent with __hci_cmd_sync_ev() which returns the sk_buff of
+ * last expected event.
+ */
+ while (remain > HCI_EVENT_HDR_SIZE && *fw_ptr[0] == 0x02) {
+ (*fw_ptr)++;
+ remain--;
+
+ evt = (struct hci_event_hdr *)(*fw_ptr);
+ *fw_ptr += sizeof(*evt);
+ remain -= sizeof(*evt);
+
+ if (remain < evt->plen) {
+ BT_ERR("%s Intel fw corrupted: invalid evt len",
+ hdev->name);
+ return -EFAULT;
+ }
+
+ evt_param = *fw_ptr;
+ *fw_ptr += evt->plen;
+ remain -= evt->plen;
+ }
+
+ /* Every HCI commands in the firmware file has its correspond event.
+ * If event is not found or remain is smaller than zero, the firmware
+ * file is corrupted.
+ */
+ if (!evt || !evt_param || remain < 0) {
+ BT_ERR("%s Intel fw corrupted: invalid evt read", hdev->name);
+ return -EFAULT;
+ }
+
+ skb = __hci_cmd_sync_ev(hdev, le16_to_cpu(cmd->opcode), cmd->plen,
+ cmd_param, evt->evt, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s sending Intel patch command (0x%4.4x) failed (%ld)",
+ hdev->name, cmd->opcode, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+
+ /* It ensures that the returned event matches the event data read from
+ * the firmware file. At fist, it checks the length and then
+ * the contents of the event.
+ */
+ if (skb->len != evt->plen) {
+ BT_ERR("%s mismatch event length (opcode 0x%4.4x)", hdev->name,
+ le16_to_cpu(cmd->opcode));
+ kfree_skb(skb);
+ return -EFAULT;
+ }
+
+ if (memcmp(skb->data, evt_param, evt->plen)) {
+ BT_ERR("%s mismatch event parameter (opcode 0x%4.4x)",
+ hdev->name, le16_to_cpu(cmd->opcode));
+ kfree_skb(skb);
+ return -EFAULT;
+ }
+ kfree_skb(skb);
+
+ return 0;
+}
+
+static int btusb_setup_intel(struct hci_dev *hdev)
+{
+ struct sk_buff *skb;
+ const struct firmware *fw;
+ const u8 *fw_ptr;
+ int disable_patch;
+ struct intel_version *ver;
+
+ const u8 mfg_enable[] = { 0x01, 0x00 };
+ const u8 mfg_disable[] = { 0x00, 0x00 };
+ const u8 mfg_reset_deactivate[] = { 0x00, 0x01 };
+ const u8 mfg_reset_activate[] = { 0x00, 0x02 };
+
+ BT_DBG("%s", hdev->name);
+
+ /* The controller has a bug with the first HCI command sent to it
+ * returning number of completed commands as zero. This would stall the
+ * command processing in the Bluetooth core.
+ *
+ * As a workaround, send HCI Reset command first which will reset the
+ * number of completed commands and allow normal command processing
+ * from now on.
+ */
+ skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s sending initial HCI reset command failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+ kfree_skb(skb);
+
+ /* Read Intel specific controller version first to allow selection of
+ * which firmware file to load.
+ *
+ * The returned information are hardware variant and revision plus
+ * firmware variant, revision and build number.
+ */
+ skb = __hci_cmd_sync(hdev, 0xfc05, 0, NULL, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s reading Intel fw version command failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+
+ if (skb->len != sizeof(*ver)) {
+ BT_ERR("%s Intel version event length mismatch", hdev->name);
+ kfree_skb(skb);
+ return -EIO;
+ }
+
+ ver = (struct intel_version *)skb->data;
+ if (ver->status) {
+ BT_ERR("%s Intel fw version event failed (%02x)", hdev->name,
+ ver->status);
+ kfree_skb(skb);
+ return -bt_to_errno(ver->status);
+ }
+
+ BT_INFO("%s: read Intel version: %02x%02x%02x%02x%02x%02x%02x%02x%02x",
+ hdev->name, ver->hw_platform, ver->hw_variant,
+ ver->hw_revision, ver->fw_variant, ver->fw_revision,
+ ver->fw_build_num, ver->fw_build_ww, ver->fw_build_yy,
+ ver->fw_patch_num);
+
+ /* fw_patch_num indicates the version of patch the device currently
+ * have. If there is no patch data in the device, it is always 0x00.
+ * So, if it is other than 0x00, no need to patch the deivce again.
+ */
+ if (ver->fw_patch_num) {
+ BT_INFO("%s: Intel device is already patched. patch num: %02x",
+ hdev->name, ver->fw_patch_num);
+ kfree_skb(skb);
+ return 0;
+ }
+
+ /* Opens the firmware patch file based on the firmware version read
+ * from the controller. If it fails to open the matching firmware
+ * patch file, it tries to open the default firmware patch file.
+ * If no patch file is found, allow the device to operate without
+ * a patch.
+ */
+ fw = btusb_setup_intel_get_fw(hdev, ver);
+ if (!fw) {
+ kfree_skb(skb);
+ return 0;
+ }
+ fw_ptr = fw->data;
+
+ /* This Intel specific command enables the manufacturer mode of the
+ * controller.
+ *
+ * Only while this mode is enabled, the driver can download the
+ * firmware patch data and configuration parameters.
+ */
+ skb = __hci_cmd_sync(hdev, 0xfc11, 2, mfg_enable, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s entering Intel manufacturer mode failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ release_firmware(fw);
+ return -PTR_ERR(skb);
+ }
+
+ if (skb->data[0]) {
+ u8 evt_status = skb->data[0];
+ BT_ERR("%s enable Intel manufacturer mode event failed (%02x)",
+ hdev->name, evt_status);
+ kfree_skb(skb);
+ release_firmware(fw);
+ return -bt_to_errno(evt_status);
+ }
+ kfree_skb(skb);
+
+ disable_patch = 1;
+
+ /* The firmware data file consists of list of Intel specific HCI
+ * commands and its expected events. The first byte indicates the
+ * type of the message, either HCI command or HCI event.
+ *
+ * It reads the command and its expected event from the firmware file,
+ * and send to the controller. Once __hci_cmd_sync_ev() returns,
+ * the returned event is compared with the event read from the firmware
+ * file and it will continue until all the messages are downloaded to
+ * the controller.
+ *
+ * Once the firmware patching is completed successfully,
+ * the manufacturer mode is disabled with reset and activating the
+ * downloaded patch.
+ *
+ * If the firmware patching fails, the manufacturer mode is
+ * disabled with reset and deactivating the patch.
+ *
+ * If the default patch file is used, no reset is done when disabling
+ * the manufacturer.
+ */
+ while (fw->size > fw_ptr - fw->data) {
+ int ret;
+
+ ret = btusb_setup_intel_patching(hdev, fw, &fw_ptr,
+ &disable_patch);
+ if (ret < 0)
+ goto exit_mfg_deactivate;
+ }
+
+ release_firmware(fw);
+
+ if (disable_patch)
+ goto exit_mfg_disable;
+
+ /* Patching completed successfully and disable the manufacturer mode
+ * with reset and activate the downloaded firmware patches.
+ */
+ skb = __hci_cmd_sync(hdev, 0xfc11, sizeof(mfg_reset_activate),
+ mfg_reset_activate, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s exiting Intel manufacturer mode failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+ kfree_skb(skb);
+
+ BT_INFO("%s: Intel Bluetooth firmware patch completed and activated",
+ hdev->name);
+
+ return 0;
+
+exit_mfg_disable:
+ /* Disable the manufacturer mode without reset */
+ skb = __hci_cmd_sync(hdev, 0xfc11, sizeof(mfg_disable), mfg_disable,
+ HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s exiting Intel manufacturer mode failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+ kfree_skb(skb);
+
+ BT_INFO("%s: Intel Bluetooth firmware patch completed", hdev->name);
+ return 0;
+
+exit_mfg_deactivate:
+ release_firmware(fw);
+
+ /* Patching failed. Disable the manufacturer mode with reset and
+ * deactivate the downloaded firmware patches.
+ */
+ skb = __hci_cmd_sync(hdev, 0xfc11, sizeof(mfg_reset_deactivate),
+ mfg_reset_deactivate, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s exiting Intel manufacturer mode failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return -PTR_ERR(skb);
+ }
+ kfree_skb(skb);
+
+ BT_INFO("%s: Intel Bluetooth firmware patch completed and deactivated",
+ hdev->name);
+
+ return 0;
+}
+
static int btusb_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
@@ -1048,6 +1423,9 @@ static int btusb_probe(struct usb_interface *intf,
if (id->driver_info & BTUSB_BCM92035)
hdev->setup = btusb_setup_bcm92035;
+ if (id->driver_info & BTUSB_INTEL)
+ hdev->setup = btusb_setup_intel;
+
/* Interface numbers are hardcoded in the specification */
data->isoc = usb_ifnum_to_if(data->udev, 1);
--
1.7.9.5
Hi Tedd,
* Tedd Ho-Jeong An <[email protected]> [2013-04-19 09:57:43 -0700]:
> From: Tedd Ho-Jeong An <[email protected]>
>
> This patch adds support for Intel Bluetooth device by adding
> btusb_setup_intel() routine that update the device with ROM patch.
>
> T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
> D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=8087 ProdID=07dc Rev= 0.01
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>
> Signed-off-by: Tedd Ho-Jeong An <[email protected]>
> ---
> v7 changes:
> - fixed endian swapping for opcode
> - removed type casting for cmd_param in in __hci_cmd_sync_ev()
> - made command param arrays to const
> - minor format change
> - required Johan's new patch: [PATCH] Bluetooth: Fix HCI command send functions to use const specifier
>
> drivers/bluetooth/btusb.c | 378 +++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 378 insertions(+)
Patch has been applied to bluetooth-next. Thanks.
Gustavo
Hi Tedd,
On Fri, Apr 19, 2013, Tedd Ho-Jeong An wrote:
> This patch adds support for Intel Bluetooth device by adding
> btusb_setup_intel() routine that update the device with ROM patch.
>
> T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
> D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=8087 ProdID=07dc Rev= 0.01
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>
> Signed-off-by: Tedd Ho-Jeong An <[email protected]>
> ---
> v7 changes:
> - fixed endian swapping for opcode
> - removed type casting for cmd_param in in __hci_cmd_sync_ev()
> - made command param arrays to const
> - minor format change
> - required Johan's new patch: [PATCH] Bluetooth: Fix HCI command send functions to use const specifier
>
> drivers/bluetooth/btusb.c | 378 +++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 378 insertions(+)
Acked-by: Johan Hedberg <[email protected]>
Johan
Hi Tedd,
> This patch adds support for Intel Bluetooth device by adding
> btusb_setup_intel() routine that update the device with ROM patch.
>
> T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
> D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=8087 ProdID=07dc Rev= 0.01
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>
> Signed-off-by: Tedd Ho-Jeong An <[email protected]>
> ---
> v7 changes:
> - fixed endian swapping for opcode
> - removed type casting for cmd_param in in __hci_cmd_sync_ev()
> - made command param arrays to const
> - minor format change
> - required Johan's new patch: [PATCH] Bluetooth: Fix HCI command send functions to use const specifier
>
> drivers/bluetooth/btusb.c | 378 +++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 378 insertions(+)
this looks good enough to me.
Acked-by: Marcel Holtmann <[email protected]>
Regards
Marcel