Add USB device ID for OQO 01+'s internal USB bluetooth
Signed-off-by: Jamie Lentin <[email protected]>
---
Whilst knowledge of the actual chipset is ropey (apparently manufactured
by CSR), it seems to work fine. I've used pand, hidd & obexftp with no
problems.
--- a/drivers/bluetooth/hci_usb.c 2009-02-04 12:34:40.000000000
+0000
+++ b/drivers/bluetooth/hci_usb.c 2009-02-04 12:35:31.000000000
+0000
@@ -97,6 +97,9 @@ static struct usb_device_id bluetooth_id
/* Canyon CN-BTU1 with HID interfaces */
{ USB_DEVICE(0x0c10, 0x0000), .driver_info = HCI_RESET },
+ /* OQO Model 01+ internal bluetooth */
+ { USB_DEVICE(0x1557, 0x0003) },
+
{ } /* Terminating entry */
};
Hi,
> Hi Jamie,
>
>> Add USB device ID for OQO 01+'s internal USB bluetooth
>
> please proof that you really need this by sending in the content
> of /proc/bus/usb/devices. Normally Bluetooth devices get identified by
> its class descriptor.
So they do. And it works fine without the patch. How embarrasing.
Apologies, I should have re-checked this. Ignore the patch.
For completeness' sake, here is the relevant chunk of
/proc/bus/usb/devices.
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1557 ProdID=0003 Rev= 9.32
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
> Also the hci_usb driver has been replaced by btusb. So please send
> patches against that kernel.
Again, thanks. Switched to using this module without problems.
> Regards
>
> Marcel
Hi Jamie,
> Add USB device ID for OQO 01+'s internal USB bluetooth
please proof that you really need this by sending in the content
of /proc/bus/usb/devices. Normally Bluetooth devices get identified by
its class descriptor.
Also the hci_usb driver has been replaced by btusb. So please send
patches against that kernel.
Regards
Marcel