All,
I cooked up a patch for the STLC2500 startup sequence.
The changes are listed below:
* Makes the firmware & parameters download optional : even though those
are supposed to be mandatory, practive shows that the chip can run
without them.
* Cleanup the speed setting step : call the Ericsson routines directly
instead of duplicating the code.
* Reset the chip only once after all settings & downloads have been done.
I couldn't regression test the file download stuff as i don't have any
firmware patch files or parameters files to download.
Denis, it would be great if you could give this patch a try on a
Greenphone, see if i didn't break anything :-)
Cheers,
Fabien
> Rereading my own code,
> same patch but with coding rules fixes :-)
>
> Fabien
Grr... wrong patch !
This one is the right one. :-)
Fabien
Rereading my own code,
same patch but with coding rules fixes :-)
Fabien
All,
I didn't notice the ST firmware was in bluez-firmware package.
So i finally was able to regression test it.
==> Result is it still works fine with firmware download too.
Cheers,
Fabien
> All,
>
> I cooked up a patch for the STLC2500 startup sequence.
> The changes are listed below:
>
> * Makes the firmware & parameters download optional : even though those
> are supposed to be mandatory, practive shows that the chip can run
> without them.
> * Cleanup the speed setting step : call the Ericsson routines directly
> instead of duplicating the code.
> * Reset the chip only once after all settings & downloads have been done.
>
> I couldn't regression test the file download stuff as i don't have any
> firmware patch files or parameters files to download.
>
> Denis, it would be great if you could give this patch a try on a
> Greenphone, see if i didn't break anything :-)
>
> Cheers,
>
> Fabien
>
>
>
> ------------------------------------------------------------------------
>
> --- tools/hciattach.c (.../trunk) (révision 89)
> +++ tools/hciattach.c (.../branches/20070928_1730) (révision 89)
> @@ -829,62 +829,20 @@
>
> extern int stlc2500_init(int fd, bdaddr_t *bdaddr);
>
> static int stlc2500(int fd, struct uart_t *u, struct termios *ti)
> {
> bdaddr_t bdaddr;
> - char cmd[5];
> unsigned char resp[10];
> int n;
> + int rvalue;
>
> - /* STLC2500 Set Baud Rate stuff */
> - /* We should set the baud rate first, so the firmware download */
> - /* goes much faster */
> -
> - /* STLC2500 Seems to support the Ericsson set baud rate stuff */
> - /* It should also support the ST Set Baud Rate command */
> - /* (as in st() function above, but those commands never succeed */
> - cmd[0] = HCI_COMMAND_PKT;
> - cmd[1] = 0x09;
> - cmd[2] = 0xfc;
> - cmd[3] = 0x01;
> -
> - switch (u->speed) {
> - case 57600:
> - cmd[4] = 0x03;
> - break;
> - case 115200:
> - cmd[4] = 0x02;
> - break;
> - case 230400:
> - cmd[4] = 0x01;
> - break;
> - case 460800:
> - cmd[4] = 0x00;
> - break;
> - case 921600:
> - cmd[4] = 0x20;
> - break;
> - default:
> - cmd[4] = 0x02;
> - u->speed = 115200;
> - break;
> - }
> -
> -#ifdef STLC2500_DEBUG
> - fprintf(stderr, "Sending Baud Rate %02x\n", cmd[4]);
> -#endif
> - /* Send initialization command */
> - if (write(fd, cmd, 5) != 5) {
> - perror("Failed to write init command");
> - return -1;
> - }
> -
> - /* Need to wait here to give a chance for the device to set baud */
> - /* But no more than 0.5 seconds */
> - usleep(200000);
> + /* STLC2500 has an ericsson core */
> + rvalue = ericsson(fd, u, ti);
> + if(rvalue != 0)
> + return rvalue;
>
> #ifdef STLC2500_DEBUG
> fprintf(stderr, "Setting speed\n");
> #endif
> if (set_speed(fd, ti, u->speed) < 0) {
> perror("Can't set baud rate");
> Index: tools/hciattach_st.c
> ===================================================================
> --- tools/hciattach_st.c (.../trunk) (révision 89)
> +++ tools/hciattach_st.c (.../branches/20070928_1730) (révision 89)
> @@ -119,13 +119,13 @@
> DIR *dir;
> struct dirent *d;
> char pathname[PATH_MAX], filename[NAME_MAX], prefix[20];
> unsigned char cmd[256];
> unsigned char buf[256];
> uint8_t seqnum = 0;
> - int fd, size, len;
> + int fd, size, len, found_fw_file;
>
> memset(filename, 0, sizeof(filename));
>
> snprintf(prefix, sizeof(prefix), "STLC2500_R%d_%02d_",
> version >> 8, version & 0xff);
>
> @@ -135,12 +135,13 @@
> strcpy(pathname, ".");
> dir = opendir(pathname);
> if (!dir)
> return -errno;
> }
>
> + found_fw_file = 0;
> while (1) {
> d = readdir(dir);
> if (!d)
> break;
>
> if (strncmp(d->d_name + strlen(d->d_name) - strlen(suffix),
> @@ -149,16 +150,20 @@
>
> if (strncmp(d->d_name, prefix, strlen(prefix)))
> continue;
>
> snprintf(filename, sizeof(filename), "%s/%s",
> pathname, d->d_name);
> + found_fw_file = 1;
> }
>
> closedir(dir);
>
> + if(!found_fw_file)
> + return -ENOENT;
> +
> printf("Loading file %s\n", filename);
>
> fd = open(filename, O_RDONLY);
> if (fd < 0) {
> perror("Can't open firmware file");
> return -errno;
> @@ -191,47 +196,54 @@
> int stlc2500_init(int dd, bdaddr_t *bdaddr)
> {
> unsigned char cmd[16];
> unsigned char buf[254];
> uint16_t version;
> int len;
> + int err;
>
> - len = do_command(dd, 0x04, 0x0001, NULL, 0, buf, sizeof(buf));
> + /* Hci_Cmd_Ericsson_Read_Revision_Information */
> + len = do_command(dd, 0xff, 0x000f, NULL, 0, buf, sizeof(buf));
> if (len < 0)
> return -1;
>
> - version = buf[2] << 8 | buf[1];
> -
> - if (load_file(dd, version, ".ptc") < 0)
> - return -1;
> + printf("%s\n", buf);
>
> - len = do_command(dd, 0x03, 0x0003, NULL, 0, buf, sizeof(buf));
> + /* HCI_Read_Local_Version_Information */
> + len = do_command(dd, 0x04, 0x0001, NULL, 0, buf, sizeof(buf));
> if (len < 0)
> return -1;
>
> - if (load_file(dd, buf[2] << 8 | buf[1], ".ssf") < 0)
> - return -1;
> -
> - len = do_command(dd, 0x03, 0x0003, NULL, 0, buf, sizeof(buf));
> - if (len < 0)
> - return -1;
> + version = buf[2] << 8 | buf[1];
>
> - len = do_command(dd, 0xff, 0x000f, NULL, 0, buf, sizeof(buf));
> - if (len < 0)
> - return -1;
> + err = load_file(dd, version, ".ptc");
> + if(err < 0) {
> + if(err == -ENOENT)
> + fprintf(stderr, "No ROM patch file loaded.\n");
> + else
> + return -1;
> + }
>
> - printf("%s\n", buf);
> + err = load_file(dd, buf[2] << 8 | buf[1], ".ssf");
> + if(err < 0) {
> + if(err == -ENOENT)
> + fprintf(stderr, "No static settings file loaded.\n");
> + else
> + return -1;
> + }
>
> cmd[0] = 0xfe;
> cmd[1] = 0x06;
> bacpy((bdaddr_t *) (cmd + 2), bdaddr);
>
> + /* Hci_Cmd_ST_Store_In_NVDS */
> len = do_command(dd, 0xff, 0x0022, cmd, 8, buf, sizeof(buf));
> if (len < 0)
> return -1;
>
> + /* HCI_Reset : applies parameters*/
> len = do_command(dd, 0x03, 0x0003, NULL, 0, buf, sizeof(buf));
> if (len < 0)
> return -1;
>
> return 0;
> }
>
>
> -------------------------------------------------------------------------
> This SF.net email is sponsored by: Splunk Inc.
> Still grepping through log files to find problems? Stop.
> Now Search log events and configuration files using AJAX and a browser.
> Download your FREE copy of Splunk now >> http://get.splunk.com/
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Bluez-devel mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/bluez-devel