Hi Henry
1,2: nop, I use standard stack come with kernel, I use csr's demo just
to test the hardware is ok.
3: the csr chip I use is initialized by sending cmd after power up .
Raymond
----- Original Message -----
From: "hong zhang" <[email protected]>
To: "colorant" <[email protected]>; "BlueZ users"
<[email protected]>
Sent: Thursday, June 12, 2008 2:04 AM
Subject: Re: [Bluez-users] How to use Bluez with CSR chip ?
> Raymond,
>
> I have a few questions.
>
> 1. Do you use CSR bleutooth stack from CSR?
> 2. If you use Bluez, you must use bluetooth stack
> comes with kernel.
> 3. How is CSR chip initialized? by eeprom?
>
>
> I believe you use CSR stack then you cannot use Bluez
> utilities.
>
> --henry
>
> --- colorant <[email protected]> wrote:
>
>> Hi henry
>>
>> Thanks for you reply.
>>
>> Yes , I am using BC4 A06 Rom version on an arm
>> based embedded board.
>>
>> So this one must set pskey before running right
>> ?
>>
>> I try to run the CSR's demo first to set the
>> right pskey and run the
>> chip up.
>> After I exit the demo, I can use pc to detect
>> the chip.
>>
>> While , then I use :
>>
>> hciattach /dev/ttyS1 bcsp 921600
>>
>> to attach ttyS1 to hci0
>>
>> after that , The PC can not detect the chip
>> anymore.
>>
>> and then I try
>> hciconfig hci0 up
>> it can bring up the hci0 interface , but the pc
>> still don't detect the
>> chip.
>>
>> for kernel , I only insert bluetooth.ko and
>> hci_uart.ko
>>
>> So , can you kindly figure out what might be
>> wrong in my operation ?
>>
>> Seems to me the hciattach operation reset the
>> chip. And I might need to
>> modify the hciattach , or ?
>>
>> Raymond
>>
>> ----- Original Message -----
>> From: "hong zhang" <[email protected]>
>> To: "BlueZ users"
>> <[email protected]>
>> Sent: Wednesday, June 11, 2008 8:57 AM
>> Subject: Re: [Bluez-users] How to use Bluez with CSR
>> chip ?
>>
>>
>> > Raymond,
>> >
>> > CSR bc4 is initialized in two ways based on your
>> > design. I assum your board is embedded. One is by
>> > eeprom and one is using command after build. You
>> need
>> > to provide more information.
>> >
>> > You have to make sure your CSR bc4 chip on your
>> board
>> > is up first before using bluez.
>> >
>> > Regular talking here is based on x86.
>> >
>> > ---henry
>> >
>> > --- colorant <[email protected]> wrote:
>> >
>> >> Hi
>> >>
>> >> I am not sure is this the proper place to put
>> up
>> >> this question, if not ,
>> >> please correct me.
>> >>
>> >> I was trying to run bluez on our board with
>> bc4
>> >> chip. This chip need to
>> >> set pskey before it can run
>> >>
>> >> I use hciattach and hciconfig to bring up the
>> >> hci0 interface.
>> >>
>> >> Then I try hcitool hci0 scan with my earphone
>> >> open.
>> >>
>> >> Nothing happend.
>> >>
>> >> while, if I using CSR's bchs a2dp demo , it's
>> >> ok, I can play music. say
>> >> hardware is ok.
>> >>
>> >> My question is :
>> >>
>> >> 1. To enable bluez with csr chip, is there
>> >> anything need to do vs the
>> >> standard kernel and bluez package ? Some config
>> >> need?
>> >>
>> >> 2. Did I need to place the bootrap init
>> sequence
>> >> for the bc4 chip in
>> >> some place if I using bluez ? say in kernel or in
>> >> the bluez user space
>> >> scripts? Or , the standard kernel and bluez
>> utility
>> >> already hand it, But I
>> >> just do the wrong way ?
>> >>
>> >>
>> >> Many thanks.
>> >> Raymond
>> >>
>> >>
>> >>
>> >>
>> >>
>> >
>>
> -------------------------------------------------------------------------
>> >> Check out the new SourceForge.net Marketplace.
>> >> It's the best place to buy or sell services for
>> >> just about anything Open Source.
>> >> http://sourceforge.net/services/buy/index.php
>> >> _______________________________________________
>> >> Bluez-users mailing list
>> >> [email protected]
>> >>
>> >
>>
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>> >>
>> >
>> >
>> >
>> >
>> >
>> >
>>
> -------------------------------------------------------------------------
>> > Check out the new SourceForge.net Marketplace.
>> > It's the best place to buy or sell services for
>> > just about anything Open Source.
>> > http://sourceforge.net/services/buy/index.php
>> > _______________________________________________
>> > Bluez-users mailing list
>> > [email protected]
>> >
>>
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>> >
>>
>>
>>
>>
>
>
>
>
>
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
That means you need bccmd to initialize your csr chip.
--- colorant <[email protected]> wrote:
> Hi Henry
>
> 1,2: nop, I use standard stack come with kernel,
> I use csr's demo just
> to test the hardware is ok.
> 3: the csr chip I use is initialized by sending
> cmd after power up .
>
> Raymond
>
>
> ----- Original Message -----
> From: "hong zhang" <[email protected]>
> To: "colorant" <[email protected]>; "BlueZ users"
> <[email protected]>
> Sent: Thursday, June 12, 2008 2:04 AM
> Subject: Re: [Bluez-users] How to use Bluez with CSR
> chip ?
>
>
> > Raymond,
> >
> > I have a few questions.
> >
> > 1. Do you use CSR bleutooth stack from CSR?
> > 2. If you use Bluez, you must use bluetooth stack
> > comes with kernel.
> > 3. How is CSR chip initialized? by eeprom?
> >
> >
> > I believe you use CSR stack then you cannot use
> Bluez
> > utilities.
> >
> > --henry
> >
> > --- colorant <[email protected]> wrote:
> >
> >> Hi henry
> >>
> >> Thanks for you reply.
> >>
> >> Yes , I am using BC4 A06 Rom version on an
> arm
> >> based embedded board.
> >>
> >> So this one must set pskey before running
> right
> >> ?
> >>
> >> I try to run the CSR's demo first to set the
> >> right pskey and run the
> >> chip up.
> >> After I exit the demo, I can use pc to detect
> >> the chip.
> >>
> >> While , then I use :
> >>
> >> hciattach /dev/ttyS1 bcsp 921600
> >>
> >> to attach ttyS1 to hci0
> >>
> >> after that , The PC can not detect the chip
> >> anymore.
> >>
> >> and then I try
> >> hciconfig hci0 up
> >> it can bring up the hci0 interface , but the
> pc
> >> still don't detect the
> >> chip.
> >>
> >> for kernel , I only insert bluetooth.ko and
> >> hci_uart.ko
> >>
> >> So , can you kindly figure out what might be
> >> wrong in my operation ?
> >>
> >> Seems to me the hciattach operation reset the
> >> chip. And I might need to
> >> modify the hciattach , or ?
> >>
> >> Raymond
> >>
> >> ----- Original Message -----
> >> From: "hong zhang" <[email protected]>
> >> To: "BlueZ users"
> >> <[email protected]>
> >> Sent: Wednesday, June 11, 2008 8:57 AM
> >> Subject: Re: [Bluez-users] How to use Bluez with
> CSR
> >> chip ?
> >>
> >>
> >> > Raymond,
> >> >
> >> > CSR bc4 is initialized in two ways based on
> your
> >> > design. I assum your board is embedded. One is
> by
> >> > eeprom and one is using command after build.
> You
> >> need
> >> > to provide more information.
> >> >
> >> > You have to make sure your CSR bc4 chip on your
> >> board
> >> > is up first before using bluez.
> >> >
> >> > Regular talking here is based on x86.
> >> >
> >> > ---henry
> >> >
> >> > --- colorant <[email protected]> wrote:
> >> >
> >> >> Hi
> >> >>
> >> >> I am not sure is this the proper place to
> put
> >> up
> >> >> this question, if not ,
> >> >> please correct me.
> >> >>
> >> >> I was trying to run bluez on our board
> with
> >> bc4
> >> >> chip. This chip need to
> >> >> set pskey before it can run
> >> >>
> >> >> I use hciattach and hciconfig to bring up
> the
> >> >> hci0 interface.
> >> >>
> >> >> Then I try hcitool hci0 scan with my
> earphone
> >> >> open.
> >> >>
> >> >> Nothing happend.
> >> >>
> >> >> while, if I using CSR's bchs a2dp demo ,
> it's
> >> >> ok, I can play music. say
> >> >> hardware is ok.
> >> >>
> >> >> My question is :
> >> >>
> >> >> 1. To enable bluez with csr chip, is there
> >> >> anything need to do vs the
> >> >> standard kernel and bluez package ? Some
> config
> >> >> need?
> >> >>
> >> >> 2. Did I need to place the bootrap init
> >> sequence
> >> >> for the bc4 chip in
> >> >> some place if I using bluez ? say in kernel or
> in
> >> >> the bluez user space
> >> >> scripts? Or , the standard kernel and bluez
> >> utility
> >> >> already hand it, But I
> >> >> just do the wrong way ?
> >> >>
> >> >>
> >> >> Many thanks.
> >> >> Raymond
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>
> >> >
> >>
> >
>
-------------------------------------------------------------------------
> >> >> Check out the new SourceForge.net Marketplace.
> >> >> It's the best place to buy or sell services
> for
> >> >> just about anything Open Source.
> >> >> http://sourceforge.net/services/buy/index.php
> >> >>
> _______________________________________________
> >> >> Bluez-users mailing list
> >> >> [email protected]
> >> >>
> >> >
> >>
> >
>
https://lists.sourceforge.net/lists/listinfo/bluez-users
> >> >>
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >>
> >
>
-------------------------------------------------------------------------
> >> > Check out the new SourceForge.net Marketplace.
> >> > It's the best place to buy or sell services for
>
=== message truncated ===
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users