2023-03-20 19:28:28

by Jeremi Piotrowski

[permalink] [raw]
Subject: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

This patch series introduces support for discovering AMD's PSP from an ACPI
table and extends the CCP driver to allow binding to that device on x86. This
method of PSP discovery is used on Hyper-V when SNP isolation support is
exposed to the guest. There is no ACPI node associated with this PSP, so after
parsing the ASPT it is registered with the system as a platform_device.

I thought about putting psp.c in arch/x86/coco, but that directory is meant for
the (confidential) guest side of CoCo, not the supporting host side code.
It was kept in arch/x86/kernel because configuring the irq for the PSP through
the ACPI interface requires poking at bits from the architectural vector
domain.

This series is a prerequisite for nested SNP-host support on Hyper-V but is
independent of the SNP-host support patch set. Hyper-V only supports nested
SEV-SNP (not SEV or SEV-ES) so the PSP only supports a subset of the full PSP
command set. Without SNP-host support (which is not upstream yet), the only
PSP command that will succeed is SEV_PLATFORM_STATUS.

Changes since v2:
* Added links to ASPT spec and ACPICA commit
* Added acked-by Tom to all commits
Changes since v1:
* move platform_device_add_data() call to commit that introduces psp device
* change psp dependency from CONFIG_AMD_MEM_ENCRYPT to CONFIG_KVM_AMD_SEV
* add blank lines, s/plat/platform/, remove variable initializers before first
use, remove masking/shifting where not needed
* dynamically allocate sev_vdata/psp_vdata structs instead of overwriting static
variables

Jeremi Piotrowski (8):
include/acpi: add definition of ASPT table
ACPI: ASPT: Add helper to parse table
x86/psp: Register PSP platform device when ASP table is present
x86/psp: Add IRQ support
crypto: cpp - Bind to psp platform device on x86
crypto: ccp - Add vdata for platform device
crypto: ccp - Skip DMA coherency check for platform psp
crypto: ccp - Allow platform device to be psp master device

arch/x86/kernel/Makefile | 1 +
arch/x86/kernel/psp.c | 219 ++++++++++++++++++++++++++++++
drivers/acpi/Makefile | 1 +
drivers/acpi/aspt.c | 104 ++++++++++++++
drivers/crypto/ccp/sp-dev.c | 65 +++++++++
drivers/crypto/ccp/sp-dev.h | 4 +
drivers/crypto/ccp/sp-pci.c | 48 -------
drivers/crypto/ccp/sp-platform.c | 76 ++++++++++-
include/acpi/actbl1.h | 46 +++++++
include/linux/platform_data/psp.h | 32 +++++
10 files changed, 547 insertions(+), 49 deletions(-)
create mode 100644 arch/x86/kernel/psp.c
create mode 100644 drivers/acpi/aspt.c
create mode 100644 include/linux/platform_data/psp.h

--
2.34.1



2023-03-20 19:36:07

by Jeremi Piotrowski

[permalink] [raw]
Subject: [PATCH v3 6/8] crypto: ccp - Add vdata for platform device

When matching the "psp" platform_device, the register offsets are
determined at runtime from the ASP ACPI table. The structure containing
the offset is passed through the platform data field provided before
registering the platform device.

To support this scenario, dynamically allocate vdata structs and fill
those in with offsets provided by the platform. Due to the fields of the
structs being const, it was necessary to use temporary structs and
memcpy, as any assignment of the whole struct fails with an 'read-only
location' compiler error.

Acked-by: Tom Lendacky <[email protected]>
Signed-off-by: Jeremi Piotrowski <[email protected]>
---
drivers/crypto/ccp/sp-platform.c | 57 ++++++++++++++++++++++++++++++++
1 file changed, 57 insertions(+)

diff --git a/drivers/crypto/ccp/sp-platform.c b/drivers/crypto/ccp/sp-platform.c
index 5dcc834deb72..2e57ec15046b 100644
--- a/drivers/crypto/ccp/sp-platform.c
+++ b/drivers/crypto/ccp/sp-platform.c
@@ -22,6 +22,7 @@
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/acpi.h>
+#include <linux/platform_data/psp.h>

#include "ccp-dev.h"

@@ -86,6 +87,60 @@ static struct sp_dev_vdata *sp_get_acpi_version(struct platform_device *pdev)
return NULL;
}

+static void sp_platform_fill_vdata(struct sp_dev_vdata *vdata, struct psp_vdata *psp,
+ struct sev_vdata *sev, const struct psp_platform_data *pdata)
+{
+ struct sev_vdata sevtmp = {
+ .cmdresp_reg = pdata->sev_cmd_resp_reg,
+ .cmdbuff_addr_lo_reg = pdata->sev_cmd_buf_lo_reg,
+ .cmdbuff_addr_hi_reg = pdata->sev_cmd_buf_hi_reg,
+ };
+ struct psp_vdata psptmp = {
+ .sev = sev,
+ .feature_reg = pdata->feature_reg,
+ .inten_reg = pdata->irq_en_reg,
+ .intsts_reg = pdata->irq_st_reg,
+ };
+
+ memcpy(sev, &sevtmp, sizeof(*sev));
+ memcpy(psp, &psptmp, sizeof(*psp));
+ vdata->psp_vdata = psp;
+}
+
+static struct sp_dev_vdata *sp_get_platform_version(struct sp_device *sp)
+{
+ struct psp_platform_data *pdata;
+ struct device *dev = sp->dev;
+ struct sp_dev_vdata *vdata;
+ struct psp_vdata *psp;
+ struct sev_vdata *sev;
+
+ pdata = dev_get_platdata(dev);
+ if (!pdata) {
+ dev_err(dev, "missing platform data\n");
+ return NULL;
+ }
+
+ vdata = devm_kzalloc(dev, sizeof(*vdata) + sizeof(*psp) + sizeof(*sev), GFP_KERNEL);
+ if (!vdata)
+ return NULL;
+
+ psp = (void *)vdata + sizeof(*vdata);
+ sev = (void *)psp + sizeof(*psp);
+ sp_platform_fill_vdata(vdata, psp, sev, pdata);
+
+ dev_dbg(dev, "PSP feature register:\t%x\n", psp->feature_reg);
+ dev_dbg(dev, "PSP IRQ enable register:\t%x\n", psp->inten_reg);
+ dev_dbg(dev, "PSP IRQ status register:\t%x\n", psp->intsts_reg);
+ dev_dbg(dev, "SEV cmdresp register:\t%x\n", sev->cmdresp_reg);
+ dev_dbg(dev, "SEV cmdbuf lo register:\t%x\n", sev->cmdbuff_addr_lo_reg);
+ dev_dbg(dev, "SEV cmdbuf hi register:\t%x\n", sev->cmdbuff_addr_hi_reg);
+ dev_dbg(dev, "SEV cmdresp IRQ:\t%x\n", pdata->mbox_irq_id);
+ dev_dbg(dev, "ACPI cmdresp register:\t%x\n", pdata->acpi_cmd_resp_reg);
+
+ return vdata;
+}
+
static int sp_get_irqs(struct sp_device *sp)
{
struct sp_platform *sp_platform = sp->dev_specific;
@@ -137,6 +192,8 @@ static int sp_platform_probe(struct platform_device *pdev)
sp->dev_specific = sp_platform;
sp->dev_vdata = pdev->dev.of_node ? sp_get_of_version(pdev)
: sp_get_acpi_version(pdev);
+ if (!sp->dev_vdata)
+ sp->dev_vdata = sp_get_platform_version(sp);
if (!sp->dev_vdata) {
ret = -ENODEV;
dev_err(dev, "missing driver data\n");
--
2.34.1


2023-03-20 19:36:11

by Jeremi Piotrowski

[permalink] [raw]
Subject: [PATCH v3 5/8] crypto: cpp - Bind to psp platform device on x86

The PSP in Hyper-V VMs is exposed through the ASP ACPI table and is
represented as a platform_device. Allow the ccp driver to bind to it by
adding an id_table and initing the platform_driver also on x86. At this
point probe is called for the psp device but init fails due to missing
driver data.

Acked-by: Tom Lendacky <[email protected]>
Signed-off-by: Jeremi Piotrowski <[email protected]>
---
drivers/crypto/ccp/sp-dev.c | 7 +++++++
drivers/crypto/ccp/sp-platform.c | 7 +++++++
2 files changed, 14 insertions(+)

diff --git a/drivers/crypto/ccp/sp-dev.c b/drivers/crypto/ccp/sp-dev.c
index 7eb3e4668286..4c9f442b8a11 100644
--- a/drivers/crypto/ccp/sp-dev.c
+++ b/drivers/crypto/ccp/sp-dev.c
@@ -259,6 +259,12 @@ static int __init sp_mod_init(void)
if (ret)
return ret;

+ ret = sp_platform_init();
+ if (ret) {
+ sp_pci_exit();
+ return ret;
+ }
+
#ifdef CONFIG_CRYPTO_DEV_SP_PSP
psp_pci_init();
#endif
@@ -286,6 +292,7 @@ static void __exit sp_mod_exit(void)
#ifdef CONFIG_CRYPTO_DEV_SP_PSP
psp_pci_exit();
#endif
+ sp_platform_exit();

sp_pci_exit();
#endif
diff --git a/drivers/crypto/ccp/sp-platform.c b/drivers/crypto/ccp/sp-platform.c
index 7d79a8744f9a..5dcc834deb72 100644
--- a/drivers/crypto/ccp/sp-platform.c
+++ b/drivers/crypto/ccp/sp-platform.c
@@ -56,6 +56,12 @@ static const struct of_device_id sp_of_match[] = {
MODULE_DEVICE_TABLE(of, sp_of_match);
#endif

+static const struct platform_device_id sp_platform_match[] = {
+ { "psp" },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, sp_platform_match);
+
static struct sp_dev_vdata *sp_get_of_version(struct platform_device *pdev)
{
#ifdef CONFIG_OF
@@ -212,6 +218,7 @@ static int sp_platform_resume(struct platform_device *pdev)
#endif

static struct platform_driver sp_platform_driver = {
+ .id_table = sp_platform_match,
.driver = {
.name = "ccp",
#ifdef CONFIG_ACPI
--
2.34.1


2023-03-20 19:41:17

by Jeremi Piotrowski

[permalink] [raw]
Subject: [PATCH v3 7/8] crypto: ccp - Skip DMA coherency check for platform psp

The value of device_get_dma_attr() is only relevenat for ARM64 and CCP
devices to configure the value of the axcache attribute used to access
memory by the coprocessor. None of this applies to the platform psp so
skip it. Skip the dma_attr check by keeping track of the fact that we
are a pure platform device.

Acked-by: Tom Lendacky <[email protected]>
Signed-off-by: Jeremi Piotrowski <[email protected]>
---
drivers/crypto/ccp/sp-platform.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/crypto/ccp/sp-platform.c b/drivers/crypto/ccp/sp-platform.c
index 2e57ec15046b..be8306c47196 100644
--- a/drivers/crypto/ccp/sp-platform.c
+++ b/drivers/crypto/ccp/sp-platform.c
@@ -29,6 +29,7 @@
struct sp_platform {
int coherent;
unsigned int irq_count;
+ bool is_platform_device;
};

static const struct sp_dev_vdata dev_vdata[] = {
@@ -109,6 +110,7 @@ static void sp_platform_fill_vdata(struct sp_dev_vdata *vdata, struct psp_vdata

static struct sp_dev_vdata *sp_get_platform_version(struct sp_device *sp)
{
+ struct sp_platform *sp_platform = sp->dev_specific;
struct psp_platform_data *pdata;
struct device *dev = sp->dev;
struct sp_dev_vdata *vdata;
@@ -129,6 +131,8 @@ static struct sp_dev_vdata *sp_get_platform_version(struct sp_device *sp)
sev = (void *)psp + sizeof(*psp);
sp_platform_fill_vdata(vdata, psp, sev, pdata);

+ sp_platform->is_platform_device = true;
+
dev_dbg(dev, "PSP feature register:\t%x\n", psp->feature_reg);
dev_dbg(dev, "PSP IRQ enable register:\t%x\n", psp->inten_reg);
dev_dbg(dev, "PSP IRQ status register:\t%x\n", psp->intsts_reg);
@@ -207,7 +211,7 @@ static int sp_platform_probe(struct platform_device *pdev)
}

attr = device_get_dma_attr(dev);
- if (attr == DEV_DMA_NOT_SUPPORTED) {
+ if (attr == DEV_DMA_NOT_SUPPORTED && !sp_platform->is_platform_device) {
dev_err(dev, "DMA is not supported");
goto e_err;
}
--
2.34.1


2023-03-20 19:41:18

by Jeremi Piotrowski

[permalink] [raw]
Subject: [PATCH v3 8/8] crypto: ccp - Allow platform device to be psp master device

Move the getters/setters to sp-dev.c, so that they can be accessed from
sp-pci.c and sp-platform.c. This makes it possible for the psp
platform_device to set the function pointers and be assigned the role of
master device by psp_dev_init().

While the case of a system having both a PCI and ACPI PSP is not
supported (and not known to occur in the wild), it makes sense to have a
single static global to assign to. Should such a system occur, the logic
in psp_set_master() is that the pci device is preferred.

Acked-by: Tom Lendacky <[email protected]>
Signed-off-by: Jeremi Piotrowski <[email protected]>
---
drivers/crypto/ccp/sp-dev.c | 58 ++++++++++++++++++++++++++++++++
drivers/crypto/ccp/sp-dev.h | 4 +++
drivers/crypto/ccp/sp-pci.c | 48 --------------------------
drivers/crypto/ccp/sp-platform.c | 6 ++++
4 files changed, 68 insertions(+), 48 deletions(-)

diff --git a/drivers/crypto/ccp/sp-dev.c b/drivers/crypto/ccp/sp-dev.c
index 4c9f442b8a11..0ac1d0eba8bb 100644
--- a/drivers/crypto/ccp/sp-dev.c
+++ b/drivers/crypto/ccp/sp-dev.c
@@ -14,6 +14,8 @@
#include <linux/kthread.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
#include <linux/spinlock.h>
#include <linux/spinlock_types.h>
#include <linux/types.h>
@@ -39,6 +41,8 @@ static LIST_HEAD(sp_units);
/* Ever-increasing value to produce unique unit numbers */
static atomic_t sp_ordinal;

+static struct sp_device *sp_dev_master;
+
static void sp_add_device(struct sp_device *sp)
{
unsigned long flags;
@@ -250,6 +254,60 @@ struct sp_device *sp_get_psp_master_device(void)
return ret;
}

+static bool sp_pci_is_master(struct sp_device *sp)
+{
+ struct device *dev_cur, *dev_new;
+ struct pci_dev *pdev_cur, *pdev_new;
+
+ dev_new = sp->dev;
+ dev_cur = sp_dev_master->dev;
+
+ pdev_new = to_pci_dev(dev_new);
+ pdev_cur = to_pci_dev(dev_cur);
+
+ if (pdev_new->bus->number < pdev_cur->bus->number)
+ return true;
+
+ if (PCI_SLOT(pdev_new->devfn) < PCI_SLOT(pdev_cur->devfn))
+ return true;
+
+ if (PCI_FUNC(pdev_new->devfn) < PCI_FUNC(pdev_cur->devfn))
+ return true;
+
+ return false;
+}
+
+void psp_set_master(struct sp_device *sp)
+{
+ struct device *dev_cur, *dev_new;
+
+ if (!sp_dev_master) {
+ sp_dev_master = sp;
+ return;
+ }
+
+ dev_new = sp->dev;
+ dev_cur = sp_dev_master->dev;
+
+ if (dev_is_pci(dev_new) && dev_is_pci(dev_cur) && sp_pci_is_master(sp))
+ sp_dev_master = sp;
+ if (dev_is_pci(dev_new) && dev_is_platform(dev_cur))
+ sp_dev_master = sp;
+}
+
+struct sp_device *psp_get_master(void)
+{
+ return sp_dev_master;
+}
+
+void psp_clear_master(struct sp_device *sp)
+{
+ if (sp == sp_dev_master) {
+ sp_dev_master = NULL;
+ dev_dbg(sp->dev, "Cleared sp_dev_master\n");
+ }
+}
+
static int __init sp_mod_init(void)
{
#ifdef CONFIG_X86
diff --git a/drivers/crypto/ccp/sp-dev.h b/drivers/crypto/ccp/sp-dev.h
index 20377e67f65d..c05f1fa82ff4 100644
--- a/drivers/crypto/ccp/sp-dev.h
+++ b/drivers/crypto/ccp/sp-dev.h
@@ -129,6 +129,10 @@ int sp_request_psp_irq(struct sp_device *sp, irq_handler_t handler,
void sp_free_psp_irq(struct sp_device *sp, void *data);
struct sp_device *sp_get_psp_master_device(void);

+void psp_set_master(struct sp_device *sp);
+struct sp_device *psp_get_master(void);
+void psp_clear_master(struct sp_device *sp);
+
#ifdef CONFIG_CRYPTO_DEV_SP_CCP

int ccp_dev_init(struct sp_device *sp);
diff --git a/drivers/crypto/ccp/sp-pci.c b/drivers/crypto/ccp/sp-pci.c
index 084d052fddcc..af8f0f65c4b5 100644
--- a/drivers/crypto/ccp/sp-pci.c
+++ b/drivers/crypto/ccp/sp-pci.c
@@ -30,7 +30,6 @@ struct sp_pci {
int msix_count;
struct msix_entry msix_entry[MSIX_VECTORS];
};
-static struct sp_device *sp_dev_master;

#define attribute_show(name, def) \
static ssize_t name##_show(struct device *d, struct device_attribute *attr, \
@@ -168,53 +167,6 @@ static void sp_free_irqs(struct sp_device *sp)
sp->psp_irq = 0;
}

-static bool sp_pci_is_master(struct sp_device *sp)
-{
- struct device *dev_cur, *dev_new;
- struct pci_dev *pdev_cur, *pdev_new;
-
- dev_new = sp->dev;
- dev_cur = sp_dev_master->dev;
-
- pdev_new = to_pci_dev(dev_new);
- pdev_cur = to_pci_dev(dev_cur);
-
- if (pdev_new->bus->number < pdev_cur->bus->number)
- return true;
-
- if (PCI_SLOT(pdev_new->devfn) < PCI_SLOT(pdev_cur->devfn))
- return true;
-
- if (PCI_FUNC(pdev_new->devfn) < PCI_FUNC(pdev_cur->devfn))
- return true;
-
- return false;
-}
-
-static void psp_set_master(struct sp_device *sp)
-{
- if (!sp_dev_master) {
- sp_dev_master = sp;
- return;
- }
-
- if (sp_pci_is_master(sp))
- sp_dev_master = sp;
-}
-
-static struct sp_device *psp_get_master(void)
-{
- return sp_dev_master;
-}
-
-static void psp_clear_master(struct sp_device *sp)
-{
- if (sp == sp_dev_master) {
- sp_dev_master = NULL;
- dev_dbg(sp->dev, "Cleared sp_dev_master\n");
- }
-}
-
static int sp_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
{
struct sp_device *sp;
diff --git a/drivers/crypto/ccp/sp-platform.c b/drivers/crypto/ccp/sp-platform.c
index be8306c47196..e22d9fee0956 100644
--- a/drivers/crypto/ccp/sp-platform.c
+++ b/drivers/crypto/ccp/sp-platform.c
@@ -234,6 +234,12 @@ static int sp_platform_probe(struct platform_device *pdev)

dev_set_drvdata(dev, sp);

+ if (sp_platform->is_platform_device) {
+ sp->set_psp_master_device = psp_set_master;
+ sp->get_psp_master_device = psp_get_master;
+ sp->clear_psp_master_device = psp_clear_master;
+ }
+
ret = sp_init(sp);
if (ret)
goto e_err;
--
2.34.1


2023-03-22 15:48:00

by Borislav Petkov

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On Mon, Mar 20, 2023 at 07:19:48PM +0000, Jeremi Piotrowski wrote:
> This series is a prerequisite for nested SNP-host support on Hyper-V

I'm curious: what in the *world* is a sensible use case for doing this
thing at all?

--
Regards/Gruss,
Boris.

https://people.kernel.org/tglx/notes-about-netiquette

2023-03-23 15:26:52

by Borislav Petkov

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On Thu, Mar 23, 2023 at 03:46:22PM +0100, Jeremi Piotrowski wrote:
> Not at all. Just to be clear: this lights up all the same bits of SNP
> as it does on bare-metal, none of it is emulated away. On bare-metal the
> hypervisor underneath the SNP guest is unencrypted as well. Here the stack
> is: L0 (Hyper-V), L1 (KVM) and L2 (SNP guest).

Yeah, I talked to folks after sending that email yesterday. Apparently
it is ok to do that without compromising SNP guest security but I, in my
eternal paranoia, somehow don't have the warm and fuzzy feeling about
it.

> ... The communication channel between L2 guest and PSP is secured
> using keys that the PSP injects into the SNP guest's address space at
> launch time.

Yeah, all the levels below L2 are required to do it set up env properly
so that L2 SNP guests can run.

> Honestly, I find it pretty cool that you can stuff a whole extra hypervisor
> underneath the SNP guest,

Whatever floats your boat. :-)

As long as it doesn't mess up my interrupt setup code with crazy hacks.

> Not sure I follow you here. The quoted paragraph talks about what the L1
> VM (KVM) sees. The L1 VM needs to issue PSP commands to bring up an L2 SNP
> guest, and later the L1 VM relays SNP guest commands to the PSP. The
> PSP commands are multiplexed to the physical PSP by the L0 hypervisor
> (Hyper-V).
>
> So Hyper-V exposes a PSP to the L1 VM because it is needed and it is
> compatible with the existing Linux driver that handles the PSP. The way
> it is exposed (ACPI table) follows how it was specified by AMD.

No no, it was specified by Microsoft architects.

So, that same interface to the PSP can be done by L0 emulating
a standard ACPI device for the KVM L1 HV and then L1 can use the normal
ACPI interrupt #9.

What's the need for supplying all that other gunk like destination ID,
interrupt vector and so on?

Thx.

--
Regards/Gruss,
Boris.

https://people.kernel.org/tglx/notes-about-netiquette

2023-03-23 16:13:21

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 3/23/2023 4:23 PM, Borislav Petkov wrote:
> On Thu, Mar 23, 2023 at 03:46:22PM +0100, Jeremi Piotrowski wrote:
>> Not at all. Just to be clear: this lights up all the same bits of SNP
>> as it does on bare-metal, none of it is emulated away. On bare-metal the
>> hypervisor underneath the SNP guest is unencrypted as well. Here the stack
>> is: L0 (Hyper-V), L1 (KVM) and L2 (SNP guest).
>
> Yeah, I talked to folks after sending that email yesterday. Apparently
> it is ok to do that without compromising SNP guest security but I, in my
> eternal paranoia, somehow don't have the warm and fuzzy feeling about
> it.
>
>> ... The communication channel between L2 guest and PSP is secured
>> using keys that the PSP injects into the SNP guest's address space at
>> launch time.
>
> Yeah, all the levels below L2 are required to do it set up env properly
> so that L2 SNP guests can run.
>
>> Honestly, I find it pretty cool that you can stuff a whole extra hypervisor
>> underneath the SNP guest,
>
> Whatever floats your boat. :-)
>
> As long as it doesn't mess up my interrupt setup code with crazy hacks.
>
>> Not sure I follow you here. The quoted paragraph talks about what the L1
>> VM (KVM) sees. The L1 VM needs to issue PSP commands to bring up an L2 SNP
>> guest, and later the L1 VM relays SNP guest commands to the PSP. The
>> PSP commands are multiplexed to the physical PSP by the L0 hypervisor
>> (Hyper-V).
>>
>> So Hyper-V exposes a PSP to the L1 VM because it is needed and it is
>> compatible with the existing Linux driver that handles the PSP. The way
>> it is exposed (ACPI table) follows how it was specified by AMD.
>
> No no, it was specified by Microsoft architects.
> > So, that same interface to the PSP can be done by L0 emulating
> a standard ACPI device for the KVM L1 HV and then L1 can use the normal
> ACPI interrupt #9.
>

That same interface is exposed by physical hardware+firmware to the underlying
Hyper-V. So it wasn't a matter of Microsoft architects coming up with a
guest-host interface but rather exposing the virtual hardware in the same
way as on a physical server.

> What's the need for supplying all that other gunk like destination ID,
> interrupt vector and so on?

I'm not sure what drove the design decisions that led to the interface looking
the way it does.
What I can do is put in the work to map it into kernel constructs in the most
native way possible and in a way that doesn't look or feel like a crazy hack.

>
> Thx.
>

2023-03-24 17:10:44

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 3/23/2023 5:34 PM, Borislav Petkov wrote:
> On Thu, Mar 23, 2023 at 05:11:26PM +0100, Jeremi Piotrowski wrote:
>> That same interface is exposed by physical hardware+firmware to the underlying
>> Hyper-V.
>
> Let me see if I understand it correctly: Hyper-V *baremetal* is using
> the same ASPT spec to to talk to the *physical* PSP device?
>

Yes

> Is that ASPT interface to talk to the PSP used by the L0 hypervisor?
>

Yes (unless I am mistaken, this is the same statement as above).

> Or does the L0 HV have a normal driver, similar to the Linux one,
> without the functionality this ASPT spec provides?
>
The L0 HV relies on the ASPT spec/interface to map registers and setup
interrupts and then uses a protocol driver to handle the PSP command set
(like the Linux one).

>> So it wasn't a matter of Microsoft architects coming up with a
>> guest-host interface but rather exposing the virtual hardware in the same
>> way as on a physical server.
>
> So if you want to expose the same interface to the L1 guest, why isn't
> Hyper-V emulating an ACPI device just like any other functionality? Why
> does it need to reach into the interrupt handling internals?
>

The primary stack for nested SNP support is Hyper-V-on-Hyper-V.
By exposing the PSP device to the L1 guest in the same way (as the L0),
everything can done in the exact same way as on bare-metal.

I just really want nested SNP support to work in KVM-on-Hyper-V as well so
that's why I'm adding support for these things.

Also: if Linux were to run bare-metal on that hardware it would need to be
able to handle the PSP through the ASPT interface as well.

> I'd expect that the L0 HV would emulate a PSP device, the L1 would
> simply load the Linux PSP device driver and everything should just work.
>
> What's the point of that alternate access at all?
>

So it's actually great that you made me ask around because I learned something that
will help:

Since the AMD PSP is a privileged device, there is a desire to not have to trust the
ACPI stack, and instead rely fully on static ACPI tables for discovery and configuration.
This also applies to the AMD IOMMU. If you look at iommu_setup_intcapxt() in
drivers/iommu/amd/init.c, it does exactly the things that are needed to setup the
PSP interrupt too. Here's a link to the patch that added that:
https://lore.kernel.org/all/[email protected]/#t

So my plan now is to post a v4 with proper irq_domain handling.
Ok Thomas?

Best wishes,
Jeremi

2023-04-02 15:46:16

by Borislav Petkov

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
> ACPI stack,

And yet you do:

+ err = acpi_parse_aspt(&res[0], &pdata);
+ if (err)
+ return err;

You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
You have to make up your mind here.

Btw, you still haven't answered my question about doing:

devm_request_irq(dev, 9, ..)

where 9 is the default ACPI interrupt.

You can have some silly table tell you what to map or you can simply map
IRQ 9 and be done with it. In this second case you can *really* not
trust ACPI because you know which IRQ it is.

--
Regards/Gruss,
Boris.

https://people.kernel.org/tglx/notes-about-netiquette

2023-04-03 06:24:03

by Thomas Gleixner

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On Sun, Apr 02 2023 at 17:44, Borislav Petkov wrote:
> On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
>> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
>> ACPI stack,
>
> And yet you do:
>
> + err = acpi_parse_aspt(&res[0], &pdata);
> + if (err)
> + return err;
>
> You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
> You have to make up your mind here.
>
> Btw, you still haven't answered my question about doing:
>
> devm_request_irq(dev, 9, ..)
>
> where 9 is the default ACPI interrupt.
>
> You can have some silly table tell you what to map or you can simply map
> IRQ 9 and be done with it. In this second case you can *really* not
> trust ACPI because you know which IRQ it is.

The real problem here is that the information provided about the overall
design and requirements is close to zero. All we heard so far is hand
waving about not trusting PCI and ACPI.

Jeremi, can you please describe exactly what the design and constraints
are in understandable and coherent sentences?

Thanks,

tglx

2023-04-05 07:57:30

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 4/3/2023 8:20 AM, Thomas Gleixner wrote:
> On Sun, Apr 02 2023 at 17:44, Borislav Petkov wrote:
>> On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
>>> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
>>> ACPI stack,
>>
>> And yet you do:
>>
>> + err = acpi_parse_aspt(&res[0], &pdata);
>> + if (err)
>> + return err;
>>
>> You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
>> You have to make up your mind here.
>>
>> Btw, you still haven't answered my question about doing:
>>
>> devm_request_irq(dev, 9, ..)
>>
>> where 9 is the default ACPI interrupt.
>>
>> You can have some silly table tell you what to map or you can simply map
>> IRQ 9 and be done with it. In this second case you can *really* not
>> trust ACPI because you know which IRQ it is

Will respond to this mail directly.

>
> The real problem here is that the information provided about the overall
> design and requirements is close to zero. All we heard so far is hand
> waving about not trusting PCI and ACPI.

That's not a fair characterization Thomas, but I will turn the other cheek.

>
> Jeremi, can you please describe exactly what the design and constraints
> are in understandable and coherent sentences?
>

Here goes, I will keep it as simple as I can.

The goal of these patches is to operate all the hardware interfaces required
to run AMD SEV-SNP VMs, but in the context of a Linux VM running on top of
Hyper-V. This Linux VM is called the SNP-host VM. All the patches I submit
target the SNP-host VM kernel, which uses KVM to bring up SEV-SNP VMs. To get
SEV-SNP working you need to combine this work with AMD's KVM SEV-SNP patches.
I posted two patch sets: one that extends AMD's patches, and one that is
independent of them (this one here) that could be merged sooner.

Here are the design constraints:
1. the interfaces exposed to the SNP-host VM to operate SEV-SNP match real
hardware interface specifications defined by AMD. This is because we are
emulating/virtualizing a hardware feature, and not some made up virtual
thing.

2. the SNP-host VM may run either Windows(Hyper-V) or Linux, so the SEV-SNP
interfaces need to be supported by both.

3. Hyper-V Generation 2 VMs do not have a PCI bus. The SNP-host VM must be a
Hyper-V Gen 2 VM.

One of the components needed to operate SEV-SNP is the Platform Security
Processor (PSP), aka AMD Secure Processor (ASP). The PSP is the root-of-trust on
AMD systems. The PSP is specified as being discoverable either on the PCI bus,
or through the presence of an ACPI table with the "ASPT" (AMD Secure Processor
Table) signature.

Here goes the design:
Constraint 1 means that only the two specified ways of discovering and
configuring a PSP inside the SNP-host VM were in the running: PCI or ASPT.
Constraint 3 means that the PCI version of the PSP is not a viable option.
Additionally, the ASPT is used on AMD hardware in Microsoft datacenters, which
means it is supported in Hyper-V (constraint 2). The outcome is that the
SNP-host VM sees an ASPT.

The ASPT provides the following information: memory range of PSP registers and
offsets of individual PSP registers inside that memory range. There are 7
registers:
- 6 are related to the "command submission" portion of the PSP; the ccp module
knows how to operate those.
- the last one, "ACPI CmdResp" register, is used to configure the PSP interrupt
to the OS.

The PSP interrupt configuration through the "ACPI CmdResp" register takes the
following information:
- APIC ID
- interrupt vector
- destination mode (physical/logical)
- message type (fixed/lowest priority)

So to hook this up with the Linux device model I wrote patches that do the
following:
Detect the ASPT table, extract information and register a "psp" platform_device
for the "ccp" module to bind to.
Create an irq_domain and encapsulate dealing with the PSP interrupt register
there, so that the "ccp" module has an irq number that it passes to
request_irq().

There is an "if (hypervisor == Hyper-V)" check before the ASPT table detection.
Here is the reasoning behind that:
According to AMD specifications the *same* PSP may be discoverable both through
ASPT and on the PCI bus. In that case, if the ASPT is to be used the OS is supposed
to disable the "PCI interface" through the "ACPI CmdResp" register, which will
result in no PCI-MSI interrupts, BAR writes ignored, BAR reads return all 0xF's.
I can't verify whether that would work correctly, so in the interest of not
breaking other users, the ASPT handling is hidden behind the hypervisor check.
There is nothing Hyper-V specific about any of this code, it supports a hardware
interface present in server grade hardware and would work on physical hardware if
when (not if) someone removes the condition.

That's all there is to it.

All the other information I gave is background information that I hoped would
help better understand the setting. The most relevant piece of information is the
one that I came across last. You asked "what makes this PSP device special". The PSP
is the root-of-trust on the system, it controls memory encryption keys, it can
encrypt/decrypt individual memory pages. SEV-SNP ties together a lot of system components
and requires enabling support for it in the AMD IOMMU too, which is presumably why
the PSP gets the same special treatment (as the AMD IOMMU). The ASPT and AMD PSP interrupt
configuration through the "ACPI CmdResp" register is based on a similar design of the AMD IOMMU.
The AMD IOMMU is:
- discovered through the presence of the IVRS ACPI table
- the MMIO address of the IOMMU is parsed out of the IVRS table
- if x2APIC support is enabled, the IOMMU interrupts are delivered based on
programming APIC-ID+vector+destination mode into an interrupt control register
in IOMMU MMIO space. This causes any PCI-MSI configuration present for the
IOMMU to be ignored.
- Linux supports and uses that interrupt delivery mechanism. It is implemented
as an irq_domain.

Do you think it makes sense to include parts of the above description in cover letter
commit message?

Thanks,
Jeremi

2023-04-05 08:12:19

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 4/3/2023 8:20 AM, Thomas Gleixner wrote:
> On Sun, Apr 02 2023 at 17:44, Borislav Petkov wrote:
>> On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
>>> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
>>> ACPI stack,
>>
>> And yet you do:
>>
>> + err = acpi_parse_aspt(&res[0], &pdata);
>> + if (err)
>> + return err;
>>
>> You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
>> You have to make up your mind here.

I gave you background on why Microsoft system designers like to use the ASPT on
*physical hardware* in our datacenters. It is because it allows them to setup a
highly privileged system component through an isolated ACPI table, without
needing to depend on the *rest of the ACPI stack* (other ACPI tables and/or the
ACPI interpreter). The same reason they use IVRS for AMD IOMMU.

I thought it might be good to write this down, as this shows that the ASPT is a
hardware interface that has *some* value. I don't think further discussion on
this point helps us make forward progress.

We're trying to adhere to a specification for a physical device when modeling
that same device in a virtual environment. Yes, this requires parsing an ACPI
table.

>>
>> Btw, you still haven't answered my question about doing:
>>
>> devm_request_irq(dev, 9, ..)
>>
>> where 9 is the default ACPI interrupt.
>>
>> You can have some silly table tell you what to map or you can simply map
>> IRQ 9 and be done with it. In this second case you can *really* not
>> trust ACPI because you know which IRQ it is.
>

So I originally thought I answered when i said "because we're trying to not
deviate from the hardware specification for the PSP". Interrupt configuration
is part of that specification.

But when I think about what you're suggesting, I can interpret it two ways:

1. Configure the PSP to raise the vector corresponding to ACPI IRQ 9.
This might work and would look similar to the first version I posted.
I'd fetch 'struct irq_cfg' for acpi_sci_irq, write the corresponding
APIC-ID/vector into the PSP, enable PSP interrupt generation and then
probe the "ccp" driver so that it can call "devm_request_irq(9)".
I assume this would also require registering an irq affinity notifier,
much like drivers/iommu/amd/init.c did before commit d1adcfbb520c.

2. Deviate from the hardware specification.
From reading acpi code (not at all an expert on this), that "9" does not
look like a static value to me, so it requires either:
a) passing a GSI number in an ACPI table
b) defining it as being the same interrupt as the SCI, which comes from
the FADT table.
c) using the GPE mechanism of the ACPI SCI interrupt.

So I'd need to define a third way for the PSP to interrupt the OS, one that
would only be supported on Hyper-V. Work with our hypervisor and/or virtual
firmware teams to make sure that the PSP model supports generating the interrupt
in this way. Work with the Windows team to make Windows support it
(the same virtual hardware model/virtual firmware is used regardless of the OS).

I have no objection to doing "1." if it works. I don't see it as a big win over
using an irq_domain.

I don't think "2." is a reasonable thing to ask. We do regularly make suggestions
to hypervisor/firmware teams on how to make things better supported in Linux
without requiring hacks. But modelling a piece of hardware in a custom way to avoid
following hardware specs is questionable.

I also think that soon, when other people deploy more SEV-SNP hardware in their
datacenters, they will also want to rely on the ASPT for the reasons listed at the
top of the email, so we'll be adding support for it anyway.

Which way do you suggest we go Boris? I'm not attached to the code at all but I am
attached to adhering to hardware specifications. I can try to do "1." or stick with
the irq_domain approach that i posted.

Thanks,
Jeremi

2023-04-05 08:56:10

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 4/2/2023 5:44 PM, Borislav Petkov wrote:
> On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
>> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
>> ACPI stack,
>
> And yet you do:
>
> + err = acpi_parse_aspt(&res[0], &pdata);
> + if (err)
> + return err;
>
> You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
> You have to make up your mind here.
>
> Btw, you still haven't answered my question about doing:
>
> devm_request_irq(dev, 9, ..)
>
> where 9 is the default ACPI interrupt.
>
> You can have some silly table tell you what to map or you can simply map
> IRQ 9 and be done with it. In this second case you can *really* not
> trust ACPI because you know which IRQ it is.
>

Sorry I broke threading. Meant to post this email:
https://lore.kernel.org/lkml/[email protected]/#t
as a reply to *this* one.

Jeremi

2023-04-11 15:11:59

by Jeremi Piotrowski

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

On 4/5/2023 9:56 AM, Jeremi Piotrowski wrote:
> On 4/3/2023 8:20 AM, Thomas Gleixner wrote:
>> On Sun, Apr 02 2023 at 17:44, Borislav Petkov wrote:
>>> On Fri, Mar 24, 2023 at 06:10:09PM +0100, Jeremi Piotrowski wrote:
>>>> Since the AMD PSP is a privileged device, there is a desire to not have to trust the
>>>> ACPI stack,
>>>
>>> And yet you do:
>>>
>>> + err = acpi_parse_aspt(&res[0], &pdata);
>>> + if (err)
>>> + return err;
>>>
>>> You don't trust the ACPI stack, and yet you're parsing an ACPI table?!?!
>>> You have to make up your mind here.
>>>
>>> Btw, you still haven't answered my question about doing:
>>>
>>> devm_request_irq(dev, 9, ..)
>>>
>>> where 9 is the default ACPI interrupt.
>>>
>>> You can have some silly table tell you what to map or you can simply map
>>> IRQ 9 and be done with it. In this second case you can *really* not
>>> trust ACPI because you know which IRQ it is
>
> Will respond to this mail directly.
>
>>
>> The real problem here is that the information provided about the overall
>> design and requirements is close to zero. All we heard so far is hand
>> waving about not trusting PCI and ACPI.
>
> That's not a fair characterization Thomas, but I will turn the other cheek.
>
>>
>> Jeremi, can you please describe exactly what the design and constraints
>> are in understandable and coherent sentences?
>>
>
> Here goes, I will keep it as simple as I can.
>
> The goal of these patches is to operate all the hardware interfaces required
> to run AMD SEV-SNP VMs, but in the context of a Linux VM running on top of
> Hyper-V. This Linux VM is called the SNP-host VM. All the patches I submit
> target the SNP-host VM kernel, which uses KVM to bring up SEV-SNP VMs. To get
> SEV-SNP working you need to combine this work with AMD's KVM SEV-SNP patches.
> I posted two patch sets: one that extends AMD's patches, and one that is
> independent of them (this one here) that could be merged sooner.
>
> Here are the design constraints:
> 1. the interfaces exposed to the SNP-host VM to operate SEV-SNP match real
> hardware interface specifications defined by AMD. This is because we are
> emulating/virtualizing a hardware feature, and not some made up virtual
> thing.
>
> 2. the SNP-host VM may run either Windows(Hyper-V) or Linux, so the SEV-SNP
> interfaces need to be supported by both.
>
> 3. Hyper-V Generation 2 VMs do not have a PCI bus. The SNP-host VM must be a
> Hyper-V Gen 2 VM.
>
> One of the components needed to operate SEV-SNP is the Platform Security
> Processor (PSP), aka AMD Secure Processor (ASP). The PSP is the root-of-trust on
> AMD systems. The PSP is specified as being discoverable either on the PCI bus,
> or through the presence of an ACPI table with the "ASPT" (AMD Secure Processor
> Table) signature.
>
> Here goes the design:
> Constraint 1 means that only the two specified ways of discovering and
> configuring a PSP inside the SNP-host VM were in the running: PCI or ASPT.
> Constraint 3 means that the PCI version of the PSP is not a viable option.
> Additionally, the ASPT is used on AMD hardware in Microsoft datacenters, which
> means it is supported in Hyper-V (constraint 2). The outcome is that the
> SNP-host VM sees an ASPT.
>
> The ASPT provides the following information: memory range of PSP registers and
> offsets of individual PSP registers inside that memory range. There are 7
> registers:
> - 6 are related to the "command submission" portion of the PSP; the ccp module
> knows how to operate those.
> - the last one, "ACPI CmdResp" register, is used to configure the PSP interrupt
> to the OS.
>
> The PSP interrupt configuration through the "ACPI CmdResp" register takes the
> following information:
> - APIC ID
> - interrupt vector
> - destination mode (physical/logical)
> - message type (fixed/lowest priority)
>
> So to hook this up with the Linux device model I wrote patches that do the
> following:
> Detect the ASPT table, extract information and register a "psp" platform_device
> for the "ccp" module to bind to.
> Create an irq_domain and encapsulate dealing with the PSP interrupt register
> there, so that the "ccp" module has an irq number that it passes to
> request_irq().
>
> There is an "if (hypervisor == Hyper-V)" check before the ASPT table detection.
> Here is the reasoning behind that:
> According to AMD specifications the *same* PSP may be discoverable both through
> ASPT and on the PCI bus. In that case, if the ASPT is to be used the OS is supposed
> to disable the "PCI interface" through the "ACPI CmdResp" register, which will
> result in no PCI-MSI interrupts, BAR writes ignored, BAR reads return all 0xF's.
> I can't verify whether that would work correctly, so in the interest of not
> breaking other users, the ASPT handling is hidden behind the hypervisor check.
> There is nothing Hyper-V specific about any of this code, it supports a hardware
> interface present in server grade hardware and would work on physical hardware if
> when (not if) someone removes the condition.
>
> That's all there is to it.
>
> All the other information I gave is background information that I hoped would
> help better understand the setting. The most relevant piece of information is the
> one that I came across last. You asked "what makes this PSP device special". The PSP
> is the root-of-trust on the system, it controls memory encryption keys, it can
> encrypt/decrypt individual memory pages. SEV-SNP ties together a lot of system components
> and requires enabling support for it in the AMD IOMMU too, which is presumably why
> the PSP gets the same special treatment (as the AMD IOMMU). The ASPT and AMD PSP interrupt
> configuration through the "ACPI CmdResp" register is based on a similar design of the AMD IOMMU.
> The AMD IOMMU is:
> - discovered through the presence of the IVRS ACPI table
> - the MMIO address of the IOMMU is parsed out of the IVRS table
> - if x2APIC support is enabled, the IOMMU interrupts are delivered based on
> programming APIC-ID+vector+destination mode into an interrupt control register
> in IOMMU MMIO space. This causes any PCI-MSI configuration present for the
> IOMMU to be ignored.
> - Linux supports and uses that interrupt delivery mechanism. It is implemented
> as an irq_domain.
>
> Do you think it makes sense to include parts of the above description in cover letter
> commit message?
>
> Thanks,
> Jeremi

Hi Thomas,

Have you had a chance to review this?

Thanks,
Jeremi

2023-04-13 21:57:43

by Thomas Gleixner

[permalink] [raw]
Subject: Re: [PATCH v3 0/8] Support ACPI PSP on Hyper-V

Jeremi!

On Wed, Apr 05 2023 at 09:56, Jeremi Piotrowski wrote:
> On 4/3/2023 8:20 AM, Thomas Gleixner wrote:

First of all. Thanks for writing this up!

> The goal of these patches is to operate all the hardware interfaces required
> to run AMD SEV-SNP VMs, but in the context of a Linux VM running on top of
> Hyper-V. This Linux VM is called the SNP-host VM. All the patches I submit
> target the SNP-host VM kernel, which uses KVM to bring up SEV-SNP VMs. To get
> SEV-SNP working you need to combine this work with AMD's KVM SEV-SNP patches.
> I posted two patch sets: one that extends AMD's patches, and one that is
> independent of them (this one here) that could be merged sooner.
>
> Here are the design constraints:
> 1. the interfaces exposed to the SNP-host VM to operate SEV-SNP match real
> hardware interface specifications defined by AMD. This is because we are
> emulating/virtualizing a hardware feature, and not some made up virtual
> thing.

Hardware/firmware folks design a lot of interfaces which are not well
thought out. The kernel has refused to implement support for those in
the past.

It's part of our development and review process to understand the
rationale behind these interfaces and if they do not make sense, tell
the vendor to fix them before we set them into stone and have to support
them forever.

And this interface _is_ fixable because it's a firmware interface and
not something cast in silicon. Firmware interfaces are versioned and
Linux has enough examples of not supporting early versions of such
interfaces.

I'm not saying it's wrong, but the lack of rationale makes me cautious.

> 2. the SNP-host VM may run either Windows(Hyper-V) or Linux, so the SEV-SNP
> interfaces need to be supported by both.
>
> 3. Hyper-V Generation 2 VMs do not have a PCI bus. The SNP-host VM must be a
> Hyper-V Gen 2 VM.

I wonder how that correlates with the patch series which adds PCI pass
through support to Hyper-V Confidential VMs....

https://lore.kernel.org/lkml/[email protected]

But that's just me being confused about a gazillion hyperv related patch
series which all fiddle something in the name of confudential computing.

It's also not really relevant to the problem at hand.

> One of the components needed to operate SEV-SNP is the Platform Security
> Processor (PSP), aka AMD Secure Processor (ASP). The PSP is the root-of-trust on
> AMD systems. The PSP is specified as being discoverable either on the PCI bus,
> or through the presence of an ACPI table with the "ASPT" (AMD Secure Processor
> Table) signature.
>
> Here goes the design:
> Constraint 1 means that only the two specified ways of discovering and
> configuring a PSP inside the SNP-host VM were in the running: PCI or ASPT.
> Constraint 3 means that the PCI version of the PSP is not a viable option.
> Additionally, the ASPT is used on AMD hardware in Microsoft datacenters, which
> means it is supported in Hyper-V (constraint 2). The outcome is that the
> SNP-host VM sees an ASPT.
>
> The ASPT provides the following information: memory range of PSP registers and
> offsets of individual PSP registers inside that memory range. There are 7
> registers:
> - 6 are related to the "command submission" portion of the PSP; the ccp module
> knows how to operate those.
> - the last one, "ACPI CmdResp" register, is used to configure the PSP interrupt
> to the OS.
>
> The PSP interrupt configuration through the "ACPI CmdResp" register takes the
> following information:
> - APIC ID
> - interrupt vector
> - destination mode (physical/logical)
> - message type (fixed/lowest priority)

This part is exactly where I started questioning, as it requires to
provide the exact data which can be written into the X2APIC ICR MSR,
which is not necessarily the most brilliant abstraction and evades
interrupt remapping completely on bare metal.

> There is nothing Hyper-V specific about any of this code, it supports a hardware
> interface present in server grade hardware and would work on physical hardware if
> when (not if) someone removes the condition.

This is _not_ a hardware interface, it's a firmware interface. The
memory window is just the transport so the OS side can talk to the PSP
firmware provided interface.

An interface with a specification which has never seen the scrutiny of
kernel developers and maintainers before you started posting these
patches. The ASPT documentation, which I saw the first time when you
provided the link, describes that interface but is completely void of
any rationale.

That's not your fault of course.

> You asked "what makes this PSP device special". The PSP is the
> root-of-trust on the system, it controls memory encryption keys, it
> can encrypt/decrypt individual memory pages.

I'm well aware what the PSP is. My question was: Why does it need
special treatment for interrupts?

> SEV-SNP ties together a lot of system components and requires enabling
> support for it in the AMD IOMMU too, which is presumably why the PSP
> gets the same special treatment (as the AMD IOMMU).

That's a fallacy. The PSP when exposed via PCI, is not treated
special. It's just assigned a regular MSI message which is composed by
the IOMMUs interrupt remapping units irqdomain.

That PCI device is not a real PCI device. It's a PCI shim which is
enumerated via PCI and provides the usual config space and bars, but the
back-end is not what we assume if we read PCI. That's true for a lot of
integrated devices on x86 (all vendors) and it's that way because PCI is
a very convenient and (most of the time) consistent way of enumeration
and configuration.

This ASPT/PSP mechanism just creates a different form of enumeration and
works completely independent of PCI. The table provides the physical
base address of the memory window and the register offsets in that
window.

That's not really much different from PCI which provides the window base
address in a PCI bar and has hard-coded device ID dependent register
offsets.

What's actually different is how the PSP interrupt is configured in the
non PCI case because it obviously can't use PCI/MSI[-x], but it still
could utilize the generic concept of MSI in theory.

> The ASPT and AMD PSP interrupt configuration through the "ACPI
> CmdResp" register is based on a similar design of the AMD IOMMU.

Sorry no. Just because X does something does not mean that Y, which
wants to do something similar, is based on the same design.

> The AMD IOMMU is:
> - discovered through the presence of the IVRS ACPI table
> - the MMIO address of the IOMMU is parsed out of the IVRS table
> - if x2APIC support is enabled, the IOMMU interrupts are delivered based on
> programming APIC-ID+vector+destination mode into an interrupt control register
> in IOMMU MMIO space. This causes any PCI-MSI configuration present for the
> IOMMU to be ignored.

That's not entirely correct.

- Interrupt remapping requires x2APIC support.

- If interrupt remapping is enabled then the interrupts of the IOMMU
and remapping unit, which deliver faults and errors, cannot go
through the remapping unit itself for obvious reasons.

So it has to have a mechanism which allows it to deliver an
interrupt to a particular destination directly w/o going through
its possibly faulty self.

Obviously Linux supports that mechanism otherwise there would be
no interrupt remapping support on Linux at all.

There is a very concise technical reason for this mechanism, but IOMMU
and PSP are technically completely different entities and the existance
of the IOMMU mechanims does not make an argument at all, that the PSP
firmware device is modeled the same way and needs to be treated the same
way.

PSP does not have the same requirement as the IOMMU. Otherwise it could
not work at all with the PCI interface which sends its interrupt message
through the interrupt remapping unit, unless the translation mechanism
does too ugly to envision nasties.

The direct firmware interface, which is just based on an ioremap'ed
address window instead of a shim PCI device, requires suddenly a
different way to configure the interrupts:

It requires to provide a full extended APIC-ID, the vector and the
control bits, ready for consumption to write into the x2APIC ICR MSR.

Which in turn, when running on bare metal evades the interrupt
remapping unit completely.

So it is _not_ the same thing as the PCI variant, which handles
bog-standard remapped MSI message format just fine. It would also handle
non-remapped format just fine _if_ IOMMU & interrupt remapping would not
be mandatory for SEV[-SNP].

There might be a concise technical reason why the direct firmware
interface can't use a regular MSI message, requires the plain x2APIC ICR
data and why it's required that the direct firmware interface can evade
interrupt remapping on bare metal, but so far nobody provided one.

Jeremi, I'm not asking you, to provide that.

There are enough AMD people on Cc who are in a better place to answer
that question. It's their specification and their firmware after all.

Though while I wrote all of this up, I found actually a technical
reason:

The shim PCI device has obviously a device ID, aka PCI BDF (Bus,
Device, Function), which allows the IOMMU/remapping code to find the
associated IOMMU and remapping table. The table is associated to the
device so the remapping unit can validate whether a particular
interrupt message is originated from the device associated to it.

The non-PCI variant does not have a device ID. That could probably be
solved, like it is solved for IOAPIC and HPET, but that requires at
least software support for IOMMU/remapping and might even require a
change in hardware as far as my limited understanding goes. Whether
that's worth it, is a completely different question.

As a consequence, this variant as of today cannot send interrupts
through the generic MSI mechanism which is routed through the
IOMMU/remapping unit and the only remaining option is to issue
interrupts directly via ICR, aka IPI.

This makes a _concise_ technical argument for the interface provided
under the following assumptions:

- It's not worth to address that device ID problem because there is
no real value as the PSP device is considered to be "correct".

- I'm not completely off track with my analysis

Let's assume those assumptions hold.

Still the existence of the IOMMU mechanism does not make an argument
for the PSP case on it's own.

Those two are two completely different reasons. The consequence that
both need a special irqdomain is the same, but that's it. See?

It's a sad state of affairs, that I had to decipher that myself, instead
of AMD folks providing this information in the documentation upfront or
at least having the courtesy of providing it in the context of this
discussion. That would have spared a lot of wasted time.

But why do I complain?

The concept of proper hardware/software co-design, which was postulated
at least 40 years ago, is still either unknown or in its infancy at the
vast majority of silicon vendors including my own employer.

The main concept is still to throw hardware/firmware over the fence and
let software folks deal with it. That's a complete disaster and paves
the way to death by complexity and unmaintainability.

As a consequence the only way for a responsible kernel maintainer is to
question the design at the point where patches are posted. Therefore
it's not unreasonable to ask for a rationale and concise technical
arguments at that point.

If the provided information does not make sense and the interface still
can be adjusted, as it is the case with pure firmware interfaces, then
there is no justification for hand-wavy arguments based on presumptions
and assumptions, really.

Again, I'm not blaming Jeremi, who has the same problem just at the
other side of the fence. First he has to make it work based on some
meager documentation and then he has to argue himself blue based on that
same meager documentation.

Can silicon folks finally get their act together and accept the fact
that the upstream Linux kernel is not there to cater to their technical
brain fart of the day?

It's the other way around. Silicon vendors rely on first class support
by the kernel, so it's their obligation to:

- integrate upstream into their specification process _upfront_
- provide concise technical documentation
- take responsibility for the kernel as a whole

IOW, the Linux kernel community has to be considered as their primary
"customer" simply because _most_ of their actually paying important
customers are depending on that.

Offloading this after the fact to paying customers who want to enable
some new feature, whether it's well thought out or not, is really not
the way to go.

It's just wasting the time of _everyone_ who is involved, except for
those vendor associated folks who stand by and ignore or silently watch
the discussions others have to fight on their behalf.

Thanks,

tglx