Removes reset_port since it isn't used anywhere as suggested by Johannes Berg.
Signed-off-by: Stanislav Yakovlev <[email protected]>
---
drivers/net/wireless/ipw2x00/libipw.h | 4 ----
drivers/net/wireless/ipw2x00/libipw_wx.c | 25 -------------------------
2 files changed, 0 insertions(+), 29 deletions(-)
diff --git a/drivers/net/wireless/ipw2x00/libipw.h b/drivers/net/wireless/ipw2x00/libipw.h
index 3d5821e..8874588 100644
--- a/drivers/net/wireless/ipw2x00/libipw.h
+++ b/drivers/net/wireless/ipw2x00/libipw.h
@@ -805,9 +805,6 @@ struct libipw_device {
/* WEP and other encryption related settings at the device level */
int open_wep; /* Set to 1 to allow unencrypted frames */
- int reset_on_keychange; /* Set to 1 if the HW needs to be reset on
- * WEP key changes */
-
/* If the host performs {en,de}cryption, then set to 1 */
int host_encrypt;
int host_encrypt_msdu;
@@ -860,7 +857,6 @@ struct libipw_device {
struct libipw_security * sec);
netdev_tx_t (*hard_start_xmit) (struct libipw_txb * txb,
struct net_device * dev, int pri);
- int (*reset_port) (struct net_device * dev);
int (*is_queue_full) (struct net_device * dev, int pri);
int (*handle_management) (struct net_device * dev,
diff --git a/drivers/net/wireless/ipw2x00/libipw_wx.c b/drivers/net/wireless/ipw2x00/libipw_wx.c
index 6623e50..1571505 100644
--- a/drivers/net/wireless/ipw2x00/libipw_wx.c
+++ b/drivers/net/wireless/ipw2x00/libipw_wx.c
@@ -474,17 +474,6 @@ int libipw_wx_set_encode(struct libipw_device *ieee,
if (ieee->set_security)
ieee->set_security(dev, &sec);
- /* Do not reset port if card is in Managed mode since resetting will
- * generate new IEEE 802.11 authentication which may end up in looping
- * with IEEE 802.1X. If your hardware requires a reset after WEP
- * configuration (for example... Prism2), implement the reset_port in
- * the callbacks structures used to initialize the 802.11 stack. */
- if (ieee->reset_on_keychange &&
- ieee->iw_mode != IW_MODE_INFRA &&
- ieee->reset_port && ieee->reset_port(dev)) {
- printk(KERN_DEBUG "%s: reset_port failed\n", dev->name);
- return -EINVAL;
- }
return 0;
}
@@ -688,20 +677,6 @@ int libipw_wx_set_encodeext(struct libipw_device *ieee,
if (ieee->set_security)
ieee->set_security(ieee->dev, &sec);
- /*
- * Do not reset port if card is in Managed mode since resetting will
- * generate new IEEE 802.11 authentication which may end up in looping
- * with IEEE 802.1X. If your hardware requires a reset after WEP
- * configuration (for example... Prism2), implement the reset_port in
- * the callbacks structures used to initialize the 802.11 stack.
- */
- if (ieee->reset_on_keychange &&
- ieee->iw_mode != IW_MODE_INFRA &&
- ieee->reset_port && ieee->reset_port(dev)) {
- LIBIPW_DEBUG_WX("%s: reset_port failed\n", dev->name);
- return -EINVAL;
- }
-
return ret;
}
--
1.7.2.5