After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <[email protected]>
---
drivers/net/wireless/ath/ath9k/ani.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c
index 47a9fb4..b4c77f9 100644
--- a/drivers/net/wireless/ath/ath9k/ani.c
+++ b/drivers/net/wireless/ath/ath9k/ani.c
@@ -274,7 +274,9 @@ static void ath9k_hw_set_ofdm_nil(struct ath_hw *ah, u8 immunityLevel)
aniState->rssiThrLow, aniState->rssiThrHigh);
if (aniState->update_ani)
- aniState->ofdmNoiseImmunityLevel = immunityLevel;
+ aniState->ofdmNoiseImmunityLevel =
+ (immunityLevel > ATH9K_ANI_OFDM_DEF_LEVEL) ?
+ immunityLevel : ATH9K_ANI_OFDM_DEF_LEVEL;
entry_ofdm = &ofdm_level_table[aniState->ofdmNoiseImmunityLevel];
entry_cck = &cck_level_table[aniState->cckNoiseImmunityLevel];
@@ -340,7 +342,9 @@ static void ath9k_hw_set_cck_nil(struct ath_hw *ah, u_int8_t immunityLevel)
immunityLevel = ATH9K_ANI_CCK_MAX_LEVEL_LOW_RSSI;
if (aniState->update_ani)
- aniState->cckNoiseImmunityLevel = immunityLevel;
+ aniState->cckNoiseImmunityLevel =
+ (immunityLevel > ATH9K_ANI_CCK_DEF_LEVEL) ?
+ immunityLevel : ATH9K_ANI_CCK_DEF_LEVEL;
entry_ofdm = &ofdm_level_table[aniState->ofdmNoiseImmunityLevel];
entry_cck = &cck_level_table[aniState->cckNoiseImmunityLevel];
--
1.7.10
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <[email protected]>
---
drivers/net/wireless/ath/ath9k/beacon.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath9k/beacon.c b/drivers/net/wireless/ath/ath9k/beacon.c
index c7f012a..8874bb5 100644
--- a/drivers/net/wireless/ath/ath9k/beacon.c
+++ b/drivers/net/wireless/ath/ath9k/beacon.c
@@ -91,7 +91,7 @@ static void ath_beacon_setup(struct ath_softc *sc, struct ieee80211_vif *vif,
info.txpower = MAX_RATE_POWER;
info.keyix = ATH9K_TXKEYIX_INVALID;
info.keytype = ATH9K_KEY_TYPE_CLEAR;
- info.flags = ATH9K_TXDESC_NOACK | ATH9K_TXDESC_INTREQ;
+ info.flags = ATH9K_TXDESC_NOACK | ATH9K_TXDESC_CLRDMASK;
info.buf_addr[0] = bf->bf_buf_addr;
info.buf_len[0] = roundup(skb->len, 4);
--
1.7.10
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <[email protected]>
---
drivers/net/wireless/ath/ath9k/beacon.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/wireless/ath/ath9k/beacon.c b/drivers/net/wireless/ath/ath9k/beacon.c
index 719a271..c7f012a 100644
--- a/drivers/net/wireless/ath/ath9k/beacon.c
+++ b/drivers/net/wireless/ath/ath9k/beacon.c
@@ -359,6 +359,11 @@ void ath_beacon_tasklet(unsigned long data)
int slot;
u32 bfaddr, bc = 0;
+ if (work_pending(&sc->hw_reset_work)) {
+ ath_dbg(common, RESET,
+ "reset work is pending, skip beaconing now\n");
+ return;
+ }
/*
* Check if the previous beacon has gone out. If
* not don't try to post another, skip this period
@@ -378,6 +383,7 @@ void ath_beacon_tasklet(unsigned long data)
ath9k_hw_bstuck_nfcal(ah);
} else if (sc->beacon.bmisscnt >= BSTUCK_THRESH) {
ath_dbg(common, BSTUCK, "beacon is officially stuck\n");
+ sc->beacon.bmisscnt = 0;
sc->sc_flags |= SC_OP_TSF_RESET;
ieee80211_queue_work(sc->hw, &sc->hw_reset_work);
}
--
1.7.10