5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <[email protected]>
---
drivers/net/wireless/ath/ath9k/ar9003_phy.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index 09facba..8927fc3 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -868,10 +868,6 @@ static void ar9003_hw_set_rfmode(struct ath_hw *ah,
if (IS_CHAN_A_FAST_CLOCK(ah, chan))
rfMode |= (AR_PHY_MODE_DYNAMIC | AR_PHY_MODE_DYN_CCK_DISABLE);
- if (IS_CHAN_QUARTER_RATE(chan))
- rfMode |= AR_PHY_MODE_QUARTER;
- if (IS_CHAN_HALF_RATE(chan))
- rfMode |= AR_PHY_MODE_HALF;
if (rfMode & (AR_PHY_MODE_QUARTER | AR_PHY_MODE_HALF))
REG_RMW_FIELD(ah, AR_PHY_FRAME_CTL,
--
1.8.3.4 (Apple Git-47)
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <[email protected]>
---
drivers/net/wireless/ath/ath9k/main.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index afce549..14a7524 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -451,7 +451,7 @@ void ath9k_tasklet(unsigned long data)
* interrupts are enabled in the reset routine.
*/
atomic_inc(&ah->intr_ref_cnt);
- ath_dbg(common, ANY, "FATAL: Skipping interrupts\n");
+ ath_dbg(common, RESET, "FATAL: Skipping interrupts\n");
goto out;
}
@@ -471,7 +471,7 @@ void ath9k_tasklet(unsigned long data)
* interrupts are enabled in the reset routine.
*/
atomic_inc(&ah->intr_ref_cnt);
- ath_dbg(common, ANY,
+ ath_dbg(common, RESET,
"BB_WATCHDOG: Skipping interrupts\n");
goto out;
}
@@ -484,7 +484,7 @@ void ath9k_tasklet(unsigned long data)
type = RESET_TYPE_TX_GTT;
ath9k_queue_reset(sc, type);
atomic_inc(&ah->intr_ref_cnt);
- ath_dbg(common, ANY,
+ ath_dbg(common, RESET,
"GTT: Skipping interrupts\n");
goto out;
}
--
1.8.3.4 (Apple Git-47)