Boot loader starts kind of new era in the driver/firmware
interaction. No more ability to boot operational firmware
from on card flash, the only way is to download from the
host.
Removed is support for the old hardware. It is not supported
any more by the new firmware. Removing it allow to compact
code a bit.
Also, after old hardware support is out, it is possible to benefit
from fixes in the new hardware. See
"enable fix for HW bug in 802.11->803.3 transform"
Boris fixed division by 0 observed on some platforms
Other are small improvements
Boris Sorochkin (1):
wil6210: Fix division by zero in wil_vring_debugfs_show
Vladimir Kondratiev (7):
wil6210: boot loader
wil6210: remove support for old hardware
wil6210: enable fix for HW bug in 802.11->803.3 transform
wil6210: branch prediction hints
wil6210: rename 'secure_pcp' to 'privacy'
wil6210: track privacy connection attribute
wil6210: Align Rx buffers on 4*n+2
Vladimir Shulman (1):
wil6210: Change of threshold for tx vring idleness measurement
drivers/net/wireless/ath/wil6210/cfg80211.c | 32 +++---
drivers/net/wireless/ath/wil6210/debugfs.c | 26 +++--
drivers/net/wireless/ath/wil6210/ethtool.c | 34 +++---
drivers/net/wireless/ath/wil6210/fw.c | 3 +-
drivers/net/wireless/ath/wil6210/fw_inc.c | 4 +-
drivers/net/wireless/ath/wil6210/interrupt.c | 70 ++++-------
drivers/net/wireless/ath/wil6210/main.c | 166 +++++++++++++++------------
drivers/net/wireless/ath/wil6210/pcie_bus.c | 22 +---
drivers/net/wireless/ath/wil6210/txrx.c | 128 ++++++++++-----------
drivers/net/wireless/ath/wil6210/wil6210.h | 34 ++++--
drivers/net/wireless/ath/wil6210/wmi.c | 9 +-
11 files changed, 252 insertions(+), 276 deletions(-)
--
2.1.0
Make this field to track privacy attribute for all interface types
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/cfg80211.c | 2 +-
drivers/net/wireless/ath/wil6210/debugfs.c | 2 +-
drivers/net/wireless/ath/wil6210/wil6210.h | 2 +-
drivers/net/wireless/ath/wil6210/wmi.c | 2 +-
4 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index 2d5ea21..38bd294 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -769,7 +769,7 @@ static int wil_cfg80211_start_ap(struct wiphy *wiphy,
wmi_set_ie(wil, WMI_FRAME_ASSOC_RESP, bcon->assocresp_ies_len,
bcon->assocresp_ies);
- wil->secure_pcp = info->privacy;
+ wil->privacy = info->privacy;
netif_carrier_on(ndev);
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index fd59751..fbe27a3 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -1400,7 +1400,7 @@ static void wil6210_debugfs_init_isr(struct wil6210_priv *wil,
/* fields in struct wil6210_priv */
static const struct dbg_off dbg_wil_off[] = {
- WIL_FIELD(secure_pcp, S_IRUGO | S_IWUSR, doff_u32),
+ WIL_FIELD(privacy, S_IRUGO, doff_u32),
WIL_FIELD(status[0], S_IRUGO | S_IWUSR, doff_ulong),
WIL_FIELD(fw_version, S_IRUGO, doff_u32),
WIL_FIELD(hw_version, S_IRUGO, doff_x32),
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 4afb8e4..b6e65c3 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -540,7 +540,7 @@ struct wil6210_priv {
wait_queue_head_t wq; /* for all wait_event() use */
/* profile */
u32 monitor_flags;
- u32 secure_pcp; /* create secure PCP? */
+ u32 privacy; /* secure connection? */
int sinfo_gen;
/* interrupt moderation */
u32 tx_max_burst_duration;
diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c
index e60186c..0213135 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.c
+++ b/drivers/net/wireless/ath/wil6210/wmi.c
@@ -874,7 +874,7 @@ int wmi_pcp_start(struct wil6210_priv *wil, int bi, u8 wmi_nettype, u8 chan)
struct wmi_pcp_started_event evt;
} __packed reply;
- if (!wil->secure_pcp)
+ if (!wil->privacy)
cmd.disable_sec = 1;
if ((cmd.pcp_max_assoc_sta > WIL6210_MAX_CID) ||
--
2.1.0
For the normal (non-sniffer) mode of operation, align Rx buffer
on 4*n+2, so IP header (after 14 bytes of Ethernet header)
will start dword aligned. This accelerated IP stack a little bit.
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/txrx.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 7f2f560..e1587b3 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -468,8 +468,11 @@ static int wil_rx_refill(struct wil6210_priv *wil, int count)
struct vring *v = &wil->vring_rx;
u32 next_tail;
int rc = 0;
+ /* 2 bytes headroom in normal operation mode to achieve dword
+ * alignment for the IP header
+ */
int headroom = ndev->type == ARPHRD_IEEE80211_RADIOTAP ?
- WIL6210_RTAP_SIZE : 0;
+ WIL6210_RTAP_SIZE : 2;
for (; next_tail = wil_vring_next_tail(v),
(next_tail != v->swhead) && (count-- > 0);
--
2.1.0
From: Vladimir Shulman <[email protected]>
Change threshold to be variable debugfs entry from hard-coded 0.
Default threshold value is 16 descriptors because HW is capable
of fetching up to 16 descriptors at once.
Signed-off-by: Vladimir Shulman <[email protected]>
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/debugfs.c | 3 ++
drivers/net/wireless/ath/wil6210/txrx.c | 52 ++++++++++++++++++++----------
drivers/net/wireless/ath/wil6210/wil6210.h | 1 +
3 files changed, 39 insertions(+), 17 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index 3ed16e7..eb6de8c 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -29,6 +29,7 @@
static u32 mem_addr;
static u32 dbg_txdesc_index;
static u32 dbg_vring_index; /* 24+ for Rx, 0..23 for Tx */
+u32 vring_idle_trsh = 16; /* HW fetches up to 16 descriptors at once */
enum dbg_off_type {
doff_u32 = 0,
@@ -1412,6 +1413,8 @@ static const struct dbg_off dbg_statics[] = {
{"desc_index", S_IRUGO | S_IWUSR, (ulong)&dbg_txdesc_index, doff_u32},
{"vring_index", S_IRUGO | S_IWUSR, (ulong)&dbg_vring_index, doff_u32},
{"mem_addr", S_IRUGO | S_IWUSR, (ulong)&mem_addr, doff_u32},
+ {"vring_idle_trsh", S_IRUGO | S_IWUSR, (ulong)&vring_idle_trsh,
+ doff_u32},
{},
};
diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 7e119d0..7f2f560 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -53,34 +53,38 @@ static inline int wil_vring_is_full(struct vring *vring)
return wil_vring_next_tail(vring) == vring->swhead;
}
-/*
- * Available space in Tx Vring
- */
-static inline int wil_vring_avail_tx(struct vring *vring)
+/* Used space in Tx Vring */
+static inline int wil_vring_used_tx(struct vring *vring)
{
u32 swhead = vring->swhead;
u32 swtail = vring->swtail;
- int used = (vring->size + swhead - swtail) % vring->size;
+ return (vring->size + swhead - swtail) % vring->size;
+}
- return vring->size - used - 1;
+/* Available space in Tx Vring */
+static inline int wil_vring_avail_tx(struct vring *vring)
+{
+ return vring->size - wil_vring_used_tx(vring) - 1;
}
-/**
- * wil_vring_wmark_low - low watermark for available descriptor space
- */
+/* wil_vring_wmark_low - low watermark for available descriptor space */
static inline int wil_vring_wmark_low(struct vring *vring)
{
return vring->size/8;
}
-/**
- * wil_vring_wmark_high - high watermark for available descriptor space
- */
+/* wil_vring_wmark_high - high watermark for available descriptor space */
static inline int wil_vring_wmark_high(struct vring *vring)
{
return vring->size/4;
}
+/* wil_val_in_range - check if value in [min,max) */
+static inline bool wil_val_in_range(int val, int min, int max)
+{
+ return val >= min && val < max;
+}
+
static int wil_vring_alloc(struct wil6210_priv *wil, struct vring *vring)
{
struct device *dev = wil_to_dev(wil);
@@ -98,8 +102,7 @@ static int wil_vring_alloc(struct wil6210_priv *wil, struct vring *vring)
vring->va = NULL;
return -ENOMEM;
}
- /*
- * vring->va should be aligned on its size rounded up to power of 2
+ /* vring->va should be aligned on its size rounded up to power of 2
* This is granted by the dma_alloc_coherent
*/
vring->va = dma_alloc_coherent(dev, sz, &vring->pa, GFP_KERNEL);
@@ -921,6 +924,7 @@ static int __wil_tx_vring(struct wil6210_priv *wil, struct vring *vring,
struct vring_tx_data *txdata = &wil->vring_tx_data[vring_index];
uint i = swhead;
dma_addr_t pa;
+ int used;
wil_dbg_txrx(wil, "%s()\n", __func__);
@@ -996,8 +1000,14 @@ static int __wil_tx_vring(struct wil6210_priv *wil, struct vring *vring,
*/
vring->ctx[i].skb = skb_get(skb);
- if (wil_vring_is_empty(vring)) /* performance monitoring */
+ /* performance monitoring */
+ used = wil_vring_used_tx(vring);
+ if (wil_val_in_range(vring_idle_trsh,
+ used, used + nr_frags + 1)) {
txdata->idle += get_cycles() - txdata->last_idle;
+ wil_dbg_txrx(wil, "Ring[%2d] not idle %d -> %d\n",
+ vring_index, used, used + nr_frags + 1);
+ }
/* advance swhead */
wil_vring_advance_head(vring, nr_frags + 1);
@@ -1141,6 +1151,8 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
int cid = wil->vring2cid_tid[ringid][0];
struct wil_net_stats *stats = &wil->sta[cid].stats;
volatile struct vring_tx_desc *_d;
+ int used_before_complete;
+ int used_new;
if (unlikely(!vring->va)) {
wil_err(wil, "Tx irq[%d]: vring not initialized\n", ringid);
@@ -1154,6 +1166,8 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
wil_dbg_txrx(wil, "%s(%d)\n", __func__, ringid);
+ used_before_complete = wil_vring_used_tx(vring);
+
while (!wil_vring_is_empty(vring)) {
int new_swtail;
struct wil_ctx *ctx = &vring->ctx[vring->swtail];
@@ -1215,8 +1229,12 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
}
}
- if (wil_vring_is_empty(vring)) { /* performance monitoring */
- wil_dbg_txrx(wil, "Ring[%2d] empty\n", ringid);
+ /* performance monitoring */
+ used_new = wil_vring_used_tx(vring);
+ if (wil_val_in_range(vring_idle_trsh,
+ used_new, used_before_complete)) {
+ wil_dbg_txrx(wil, "Ring[%2d] idle %d -> %d\n",
+ ringid, used_before_complete, used_new);
txdata->last_idle = get_cycles();
}
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 85f0011..4afb8e4 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -27,6 +27,7 @@ extern bool no_fw_recovery;
extern unsigned int mtu_max;
extern unsigned short rx_ring_overflow_thrsh;
extern int agg_wsize;
+extern u32 vring_idle_trsh;
#define WIL_NAME "wil6210"
#define WIL_FW_NAME "wil6210.fw" /* code */
--
2.1.0
Mark expected branches using likely()/unlikely().
Do it on high performance route - data path and interrupts
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/interrupt.c | 25 ++++++++---------
drivers/net/wireless/ath/wil6210/txrx.c | 40 ++++++++++++++--------------
2 files changed, 33 insertions(+), 32 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c
index d5a651b..28ffc18 100644
--- a/drivers/net/wireless/ath/wil6210/interrupt.c
+++ b/drivers/net/wireless/ath/wil6210/interrupt.c
@@ -226,7 +226,7 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
trace_wil6210_irq_rx(isr);
wil_dbg_irq(wil, "ISR RX 0x%08x\n", isr);
- if (!isr) {
+ if (unlikely(!isr)) {
wil_err(wil, "spurious IRQ: RX\n");
return IRQ_NONE;
}
@@ -239,17 +239,18 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
* action is always the same - should empty the accumulated
* packets from the RX ring.
*/
- if (isr & (BIT_DMA_EP_RX_ICR_RX_DONE | BIT_DMA_EP_RX_ICR_RX_HTRSH)) {
+ if (likely(isr & (BIT_DMA_EP_RX_ICR_RX_DONE |
+ BIT_DMA_EP_RX_ICR_RX_HTRSH))) {
wil_dbg_irq(wil, "RX done\n");
- if (isr & BIT_DMA_EP_RX_ICR_RX_HTRSH)
+ if (unlikely(isr & BIT_DMA_EP_RX_ICR_RX_HTRSH))
wil_err_ratelimited(wil,
"Received \"Rx buffer is in risk of overflow\" interrupt\n");
isr &= ~(BIT_DMA_EP_RX_ICR_RX_DONE |
BIT_DMA_EP_RX_ICR_RX_HTRSH);
- if (test_bit(wil_status_reset_done, wil->status)) {
- if (test_bit(wil_status_napi_en, wil->status)) {
+ if (likely(test_bit(wil_status_reset_done, wil->status))) {
+ if (likely(test_bit(wil_status_napi_en, wil->status))) {
wil_dbg_txrx(wil, "NAPI(Rx) schedule\n");
need_unmask = false;
napi_schedule(&wil->napi_rx);
@@ -262,7 +263,7 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
}
}
- if (isr)
+ if (unlikely(isr))
wil_err(wil, "un-handled RX ISR bits 0x%08x\n", isr);
/* Rx IRQ will be enabled when NAPI processing finished */
@@ -286,19 +287,19 @@ static irqreturn_t wil6210_irq_tx(int irq, void *cookie)
trace_wil6210_irq_tx(isr);
wil_dbg_irq(wil, "ISR TX 0x%08x\n", isr);
- if (!isr) {
+ if (unlikely(!isr)) {
wil_err(wil, "spurious IRQ: TX\n");
return IRQ_NONE;
}
wil6210_mask_irq_tx(wil);
- if (isr & BIT_DMA_EP_TX_ICR_TX_DONE) {
+ if (likely(isr & BIT_DMA_EP_TX_ICR_TX_DONE)) {
wil_dbg_irq(wil, "TX done\n");
isr &= ~BIT_DMA_EP_TX_ICR_TX_DONE;
/* clear also all VRING interrupts */
isr &= ~(BIT(25) - 1UL);
- if (test_bit(wil_status_reset_done, wil->status)) {
+ if (likely(test_bit(wil_status_reset_done, wil->status))) {
wil_dbg_txrx(wil, "NAPI(Tx) schedule\n");
need_unmask = false;
napi_schedule(&wil->napi_tx);
@@ -307,7 +308,7 @@ static irqreturn_t wil6210_irq_tx(int irq, void *cookie)
}
}
- if (isr)
+ if (unlikely(isr))
wil_err(wil, "un-handled TX ISR bits 0x%08x\n", isr);
/* Tx IRQ will be enabled when NAPI processing finished */
@@ -496,11 +497,11 @@ static irqreturn_t wil6210_hardirq(int irq, void *cookie)
/**
* pseudo_cause is Clear-On-Read, no need to ACK
*/
- if ((pseudo_cause == 0) || ((pseudo_cause & 0xff) == 0xff))
+ if (unlikely((pseudo_cause == 0) || ((pseudo_cause & 0xff) == 0xff)))
return IRQ_NONE;
/* FIXME: IRQ mask debug */
- if (wil6210_debug_irq_mask(wil, pseudo_cause))
+ if (unlikely(wil6210_debug_irq_mask(wil, pseudo_cause)))
return IRQ_NONE;
trace_wil6210_irq_pseudo(pseudo_cause);
diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 779d836..7e119d0 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -370,11 +370,11 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
BUILD_BUG_ON(sizeof(struct vring_rx_desc) > sizeof(skb->cb));
- if (wil_vring_is_empty(vring))
+ if (unlikely(wil_vring_is_empty(vring)))
return NULL;
_d = &vring->va[vring->swhead].rx;
- if (!(_d->dma.status & RX_DMA_STATUS_DU)) {
+ if (unlikely(!(_d->dma.status & RX_DMA_STATUS_DU))) {
/* it is not error, we just reached end of Rx done area */
return NULL;
}
@@ -394,7 +394,7 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
wil_hex_dump_txrx("Rx ", DUMP_PREFIX_NONE, 32, 4,
(const void *)d, sizeof(*d), false);
- if (dmalen > sz) {
+ if (unlikely(dmalen > sz)) {
wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
kfree_skb(skb);
return NULL;
@@ -423,14 +423,14 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
* in Rx descriptor. If type is not data, it is 802.11 frame as is
*/
ftype = wil_rxdesc_ftype(d) << 2;
- if (ftype != IEEE80211_FTYPE_DATA) {
+ if (unlikely(ftype != IEEE80211_FTYPE_DATA)) {
wil_dbg_txrx(wil, "Non-data frame ftype 0x%08x\n", ftype);
/* TODO: process it */
kfree_skb(skb);
return NULL;
}
- if (skb->len < ETH_HLEN) {
+ if (unlikely(skb->len < ETH_HLEN)) {
wil_err(wil, "Short frame, len = %d\n", skb->len);
/* TODO: process it (i.e. BAR) */
kfree_skb(skb);
@@ -441,9 +441,9 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
* and in case of error drop the packet
* higher stack layers will handle retransmission (if required)
*/
- if (d->dma.status & RX_DMA_STATUS_L4I) {
+ if (likely(d->dma.status & RX_DMA_STATUS_L4I)) {
/* L4 protocol identified, csum calculated */
- if ((d->dma.error & RX_DMA_ERROR_L4_ERR) == 0)
+ if (likely((d->dma.error & RX_DMA_ERROR_L4_ERR) == 0))
skb->ip_summed = CHECKSUM_UNNECESSARY;
/* If HW reports bad checksum, let IP stack re-check it
* For example, HW don't understand Microsoft IP stack that
@@ -472,7 +472,7 @@ static int wil_rx_refill(struct wil6210_priv *wil, int count)
(next_tail != v->swhead) && (count-- > 0);
v->swtail = next_tail) {
rc = wil_vring_alloc_skb(wil, v, v->swtail, headroom);
- if (rc) {
+ if (unlikely(rc)) {
wil_err(wil, "Error %d in wil_rx_refill[%d]\n",
rc, v->swtail);
break;
@@ -534,7 +534,7 @@ void wil_rx_handle(struct wil6210_priv *wil, int *quota)
struct vring *v = &wil->vring_rx;
struct sk_buff *skb;
- if (!v->va) {
+ if (unlikely(!v->va)) {
wil_err(wil, "Rx IRQ while Rx not yet initialized\n");
return;
}
@@ -927,7 +927,7 @@ static int __wil_tx_vring(struct wil6210_priv *wil, struct vring *vring,
if (unlikely(!txdata->enabled))
return -EINVAL;
- if (avail < 1 + nr_frags) {
+ if (unlikely(avail < 1 + nr_frags)) {
wil_err_ratelimited(wil,
"Tx ring[%2d] full. No space for %d fragments\n",
vring_index, 1 + nr_frags);
@@ -948,7 +948,7 @@ static int __wil_tx_vring(struct wil6210_priv *wil, struct vring *vring,
/* 1-st segment */
wil_tx_desc_map(d, pa, skb_headlen(skb), vring_index);
/* Process TCP/UDP checksum offloading */
- if (wil_tx_desc_offload_cksum_set(wil, d, skb)) {
+ if (unlikely(wil_tx_desc_offload_cksum_set(wil, d, skb))) {
wil_err(wil, "Tx[%2d] Failed to set cksum, drop packet\n",
vring_index);
goto dma_error;
@@ -1051,18 +1051,18 @@ netdev_tx_t wil_start_xmit(struct sk_buff *skb, struct net_device *ndev)
int rc;
wil_dbg_txrx(wil, "%s()\n", __func__);
- if (!test_bit(wil_status_fwready, wil->status)) {
+ if (unlikely(!test_bit(wil_status_fwready, wil->status))) {
if (!pr_once_fw) {
wil_err(wil, "FW not ready\n");
pr_once_fw = true;
}
goto drop;
}
- if (!test_bit(wil_status_fwconnected, wil->status)) {
+ if (unlikely(!test_bit(wil_status_fwconnected, wil->status))) {
wil_err(wil, "FW not connected\n");
goto drop;
}
- if (wil->wdev->iftype == NL80211_IFTYPE_MONITOR) {
+ if (unlikely(wil->wdev->iftype == NL80211_IFTYPE_MONITOR)) {
wil_err(wil, "Xmit in monitor mode not supported\n");
goto drop;
}
@@ -1078,7 +1078,7 @@ netdev_tx_t wil_start_xmit(struct sk_buff *skb, struct net_device *ndev)
else
vring = wil_tx_bcast(wil, skb);
}
- if (!vring) {
+ if (unlikely(!vring)) {
wil_dbg_txrx(wil, "No Tx VRING found for %pM\n", eth->h_dest);
goto drop;
}
@@ -1086,7 +1086,7 @@ netdev_tx_t wil_start_xmit(struct sk_buff *skb, struct net_device *ndev)
rc = wil_tx_vring(wil, vring, skb);
/* do we still have enough room in the vring? */
- if (wil_vring_avail_tx(vring) < wil_vring_wmark_low(vring)) {
+ if (unlikely(wil_vring_avail_tx(vring) < wil_vring_wmark_low(vring))) {
netif_tx_stop_all_queues(wil_to_ndev(wil));
wil_dbg_txrx(wil, "netif_tx_stop : ring full\n");
}
@@ -1142,12 +1142,12 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
struct wil_net_stats *stats = &wil->sta[cid].stats;
volatile struct vring_tx_desc *_d;
- if (!vring->va) {
+ if (unlikely(!vring->va)) {
wil_err(wil, "Tx irq[%d]: vring not initialized\n", ringid);
return 0;
}
- if (!txdata->enabled) {
+ if (unlikely(!txdata->enabled)) {
wil_info(wil, "Tx irq[%d]: vring disabled\n", ringid);
return 0;
}
@@ -1165,7 +1165,7 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
/* TODO: check we are not past head */
_d = &vring->va[lf].tx;
- if (!(_d->dma.status & TX_DMA_STATUS_DU))
+ if (unlikely(!(_d->dma.status & TX_DMA_STATUS_DU)))
break;
new_swtail = (lf + 1) % vring->size;
@@ -1193,7 +1193,7 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
wil_txdesc_unmap(dev, d, ctx);
if (skb) {
- if (d->dma.error == 0) {
+ if (likely(d->dma.error == 0)) {
ndev->stats.tx_packets++;
stats->tx_packets++;
ndev->stats.tx_bytes += skb->len;
--
2.1.0
On Sunday, February 15, 2015 02:02:38 PM Vladimir Kondratiev wrote:
> For the normal (non-sniffer) mode of operation, align Rx buffer
> on 4*n+2, so IP header (after 14 bytes of Ethernet header)
> will start dword aligned. This accelerated IP stack a little bit.
>
> Signed-off-by: Vladimir Kondratiev <[email protected]>
>
Kalle,
please do not apply this patch. I found last minute problem with it -
hardware is not always happy.
For now, drop it please. I will do more testing and re-submit this
patch if everything wends OK.
Thanks, Vladimir
For the STA interface, track 'privacy'.
Refactor safety checks to:
- always print connection params
- always check IE size validity
- require RSN IE for secure connection
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/cfg80211.c | 30 +++++++++++++++++------------
1 file changed, 18 insertions(+), 12 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index 38bd294..4bd708c 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -387,11 +387,25 @@ static int wil_cfg80211_connect(struct wiphy *wiphy,
int ch;
int rc = 0;
+ wil_print_connect_params(wil, sme);
+
if (test_bit(wil_status_fwconnecting, wil->status) ||
test_bit(wil_status_fwconnected, wil->status))
return -EALREADY;
- wil_print_connect_params(wil, sme);
+ if (sme->ie_len > WMI_MAX_IE_LEN) {
+ wil_err(wil, "IE too large (%td bytes)\n", sme->ie_len);
+ return -ERANGE;
+ }
+
+ rsn_eid = sme->ie ?
+ cfg80211_find_ie(WLAN_EID_RSN, sme->ie, sme->ie_len) :
+ NULL;
+
+ if (sme->privacy && !rsn_eid) {
+ wil_err(wil, "Missing RSN IE for secure connection\n");
+ return -EINVAL;
+ }
bss = cfg80211_get_bss(wiphy, sme->channel, sme->bssid,
sme->ssid, sme->ssid_len,
@@ -407,17 +421,9 @@ static int wil_cfg80211_connect(struct wiphy *wiphy,
rc = -ENOENT;
goto out;
}
+ wil->privacy = sme->privacy;
- rsn_eid = sme->ie ?
- cfg80211_find_ie(WLAN_EID_RSN, sme->ie, sme->ie_len) :
- NULL;
- if (rsn_eid) {
- if (sme->ie_len > WMI_MAX_IE_LEN) {
- rc = -ERANGE;
- wil_err(wil, "IE too large (%td bytes)\n",
- sme->ie_len);
- goto out;
- }
+ if (wil->privacy) {
/* For secure assoc, send WMI_DELETE_CIPHER_KEY_CMD */
rc = wmi_del_cipher_key(wil, 0, bss->bssid);
if (rc) {
@@ -450,7 +456,7 @@ static int wil_cfg80211_connect(struct wiphy *wiphy,
bss->capability);
goto out;
}
- if (rsn_eid) {
+ if (wil->privacy) {
conn.dot11_auth_mode = WMI_AUTH11_SHARED;
conn.auth_mode = WMI_AUTH_WPA2_PSK;
conn.pairwise_crypto_type = WMI_CRYPT_AES_GCMP;
--
2.1.0
From: Boris Sorochkin <[email protected]>
On some platforms get_cycles() implemented to allways return 0.
On such platforms "Division by zero" bug was triggered.
Signed-off-by: Boris Sorochkin <[email protected]>
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/debugfs.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index eb6de8c..fd59751 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -103,23 +103,30 @@ static int wil_vring_debugfs_show(struct seq_file *s, void *data)
% vring->size;
int avail = vring->size - used - 1;
char name[10];
+ char sidle[10];
/* performance monitoring */
cycles_t now = get_cycles();
uint64_t idle = txdata->idle * 100;
uint64_t total = now - txdata->begin;
- do_div(idle, total);
+ if (total != 0) {
+ do_div(idle, total);
+ snprintf(sidle, sizeof(sidle), "%3d%%",
+ (int)idle);
+ } else {
+ snprintf(sidle, sizeof(sidle), "N/A");
+ }
txdata->begin = now;
txdata->idle = 0ULL;
snprintf(name, sizeof(name), "tx_%2d", i);
seq_printf(s,
- "\n%pM CID %d TID %d BACK([%d] %d TU A%s) [%3d|%3d] idle %3d%%\n",
- wil->sta[cid].addr, cid, tid,
- txdata->agg_wsize, txdata->agg_timeout,
- txdata->agg_amsdu ? "+" : "-",
- used, avail, (int)idle);
+ "\n%pM CID %d TID %d BACK([%d] %d TU A%s) [%3d|%3d] idle %s\n",
+ wil->sta[cid].addr, cid, tid,
+ txdata->agg_wsize, txdata->agg_timeout,
+ txdata->agg_amsdu ? "+" : "-",
+ used, avail, sidle);
wil_print_vring(s, wil, name, vring, '_', 'H');
}
--
2.1.0
Hardware older than Sparrow B0 obsolete.
There is no WiFi product that uses this hardware.
Recent firmware does not support it either.
Remove driver support.
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/ethtool.c | 34 +++++++---------
drivers/net/wireless/ath/wil6210/interrupt.c | 45 +++++----------------
drivers/net/wireless/ath/wil6210/main.c | 58 ++++++++++------------------
drivers/net/wireless/ath/wil6210/pcie_bus.c | 20 ----------
drivers/net/wireless/ath/wil6210/wil6210.h | 8 ----
5 files changed, 42 insertions(+), 123 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/ethtool.c b/drivers/net/wireless/ath/wil6210/ethtool.c
index 4c44a82..0ea695f 100644
--- a/drivers/net/wireless/ath/wil6210/ethtool.c
+++ b/drivers/net/wireless/ath/wil6210/ethtool.c
@@ -50,27 +50,19 @@ static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
wil_dbg_misc(wil, "%s()\n", __func__);
- if (test_bit(hw_capability_advanced_itr_moderation,
- wil->hw_capabilities)) {
- tx_itr_en = ioread32(wil->csr +
- HOSTADDR(RGF_DMA_ITR_TX_CNT_CTL));
- if (tx_itr_en & BIT_DMA_ITR_TX_CNT_CTL_EN)
- tx_itr_val =
- ioread32(wil->csr +
- HOSTADDR(RGF_DMA_ITR_TX_CNT_TRSH));
-
- rx_itr_en = ioread32(wil->csr +
- HOSTADDR(RGF_DMA_ITR_RX_CNT_CTL));
- if (rx_itr_en & BIT_DMA_ITR_RX_CNT_CTL_EN)
- rx_itr_val =
- ioread32(wil->csr +
- HOSTADDR(RGF_DMA_ITR_RX_CNT_TRSH));
- } else {
- rx_itr_en = ioread32(wil->csr + HOSTADDR(RGF_DMA_ITR_CNT_CRL));
- if (rx_itr_en & BIT_DMA_ITR_CNT_CRL_EN)
- rx_itr_val = ioread32(wil->csr +
- HOSTADDR(RGF_DMA_ITR_CNT_TRSH));
- }
+ tx_itr_en = ioread32(wil->csr +
+ HOSTADDR(RGF_DMA_ITR_TX_CNT_CTL));
+ if (tx_itr_en & BIT_DMA_ITR_TX_CNT_CTL_EN)
+ tx_itr_val =
+ ioread32(wil->csr +
+ HOSTADDR(RGF_DMA_ITR_TX_CNT_TRSH));
+
+ rx_itr_en = ioread32(wil->csr +
+ HOSTADDR(RGF_DMA_ITR_RX_CNT_CTL));
+ if (rx_itr_en & BIT_DMA_ITR_RX_CNT_CTL_EN)
+ rx_itr_val =
+ ioread32(wil->csr +
+ HOSTADDR(RGF_DMA_ITR_RX_CNT_TRSH));
cp->tx_coalesce_usecs = tx_itr_val;
cp->rx_coalesce_usecs = rx_itr_val;
diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c
index a6f9230..d5a651b 100644
--- a/drivers/net/wireless/ath/wil6210/interrupt.c
+++ b/drivers/net/wireless/ath/wil6210/interrupt.c
@@ -166,9 +166,16 @@ void wil_unmask_irq(struct wil6210_priv *wil)
/* target write operation */
#define W(a, v) do { iowrite32(v, wil->csr + HOSTADDR(a)); wmb(); } while (0)
-static
-void wil_configure_interrupt_moderation_new(struct wil6210_priv *wil)
+void wil_configure_interrupt_moderation(struct wil6210_priv *wil)
{
+ wil_dbg_irq(wil, "%s()\n", __func__);
+
+ /* disable interrupt moderation for monitor
+ * to get better timestamp precision
+ */
+ if (wil->wdev->iftype == NL80211_IFTYPE_MONITOR)
+ return;
+
/* Disable and clear tx counter before (re)configuration */
W(RGF_DMA_ITR_TX_CNT_CTL, BIT_DMA_ITR_TX_CNT_CTL_CLR);
W(RGF_DMA_ITR_TX_CNT_TRSH, wil->tx_max_burst_duration);
@@ -206,42 +213,8 @@ void wil_configure_interrupt_moderation_new(struct wil6210_priv *wil)
BIT_DMA_ITR_RX_IDL_CNT_CTL_EXT_TIC_SEL);
}
-static
-void wil_configure_interrupt_moderation_lgc(struct wil6210_priv *wil)
-{
- /* disable, use usec resolution */
- W(RGF_DMA_ITR_CNT_CRL, BIT_DMA_ITR_CNT_CRL_CLR);
-
- wil_info(wil, "set ITR_TRSH = %d usec\n", wil->rx_max_burst_duration);
- W(RGF_DMA_ITR_CNT_TRSH, wil->rx_max_burst_duration);
- /* start it */
- W(RGF_DMA_ITR_CNT_CRL,
- BIT_DMA_ITR_CNT_CRL_EN | BIT_DMA_ITR_CNT_CRL_EXT_TICK);
-}
-
#undef W
-void wil_configure_interrupt_moderation(struct wil6210_priv *wil)
-{
- wil_dbg_irq(wil, "%s()\n", __func__);
-
- /* disable interrupt moderation for monitor
- * to get better timestamp precision
- */
- if (wil->wdev->iftype == NL80211_IFTYPE_MONITOR)
- return;
-
- if (test_bit(hw_capability_advanced_itr_moderation,
- wil->hw_capabilities))
- wil_configure_interrupt_moderation_new(wil);
- else {
- /* Advanced interrupt moderation is not available before
- * Sparrow v2. Will use legacy interrupt moderation
- */
- wil_configure_interrupt_moderation_lgc(wil);
- }
-}
-
static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
{
struct wil6210_priv *wil = cookie;
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index acbbd27..95755a5 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -516,8 +516,6 @@ static int wil_target_reset(struct wil6210_priv *wil)
{
int delay = 0;
u32 x;
- bool is_reset_v2 = test_bit(hw_capability_reset_v2,
- wil->hw_capabilities);
wil_dbg_misc(wil, "Resetting \"%s\"...\n", wil->hw_name);
@@ -533,52 +531,39 @@ static int wil_target_reset(struct wil6210_priv *wil)
/* Clear Fw Download notification */
C(RGF_USER_USAGE_6, BIT(0));
- if (is_reset_v2) {
- S(RGF_CAF_OSC_CONTROL, BIT_CAF_OSC_XTAL_EN);
- /* XTAL stabilization should take about 3ms */
- usleep_range(5000, 7000);
- x = R(RGF_CAF_PLL_LOCK_STATUS);
- if (!(x & BIT_CAF_OSC_DIG_XTAL_STABLE)) {
- wil_err(wil, "Xtal stabilization timeout\n"
- "RGF_CAF_PLL_LOCK_STATUS = 0x%08x\n", x);
- return -ETIME;
- }
- /* switch 10k to XTAL*/
- C(RGF_USER_SPARROW_M_4, BIT_SPARROW_M_4_SEL_SLEEP_OR_REF);
- /* 40 MHz */
- C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_CAR_AHB_SW_SEL);
-
- W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x3ff81f);
- W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1, 0xf);
+ S(RGF_CAF_OSC_CONTROL, BIT_CAF_OSC_XTAL_EN);
+ /* XTAL stabilization should take about 3ms */
+ usleep_range(5000, 7000);
+ x = R(RGF_CAF_PLL_LOCK_STATUS);
+ if (!(x & BIT_CAF_OSC_DIG_XTAL_STABLE)) {
+ wil_err(wil, "Xtal stabilization timeout\n"
+ "RGF_CAF_PLL_LOCK_STATUS = 0x%08x\n", x);
+ return -ETIME;
}
+ /* switch 10k to XTAL*/
+ C(RGF_USER_SPARROW_M_4, BIT_SPARROW_M_4_SEL_SLEEP_OR_REF);
+ /* 40 MHz */
+ C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_CAR_AHB_SW_SEL);
+
+ W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x3ff81f);
+ W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1, 0xf);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0xFE000000);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_1, 0x0000003F);
- W(RGF_USER_CLKS_CTL_SW_RST_VEC_3,
- is_reset_v2 ? 0x000000f0 : 0x00000170);
+ W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x000000f0);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0xFFE7FE00);
- if (is_reset_v2) {
- W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x0);
- W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1, 0x0);
- }
+ W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x0);
+ W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_1, 0x0);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_1, 0);
W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
- if (is_reset_v2) {
- W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x00000003);
- /* reset A2 PCIE AHB */
- W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00008000);
- } else {
- W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x00000001);
- W(RGF_PCIE_LOS_COUNTER_CTL, BIT(6) | BIT(8));
- W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00008000);
- }
+ W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x00000003);
+ W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00008000); /* reset A2 PCIE AHB */
- /* TODO: check order here!!! Erez code is different */
W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
/* wait until device ready. typical time is 20..80 msec */
@@ -592,9 +577,6 @@ static int wil_target_reset(struct wil6210_priv *wil)
}
} while (!(x & BIT_BL_READY));
- if (!is_reset_v2)
- W(RGF_PCIE_LOS_COUNTER_CTL, BIT(8));
-
C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_RST_PWGD);
wil_dbg_misc(wil, "Reset completed in %d ms\n", delay * RST_DELAY);
diff --git a/drivers/net/wireless/ath/wil6210/pcie_bus.c b/drivers/net/wireless/ath/wil6210/pcie_bus.c
index f7c165d..25343cf 100644
--- a/drivers/net/wireless/ath/wil6210/pcie_bus.c
+++ b/drivers/net/wireless/ath/wil6210/pcie_bus.c
@@ -39,18 +39,6 @@ void wil_set_capabilities(struct wil6210_priv *wil)
bitmap_zero(wil->hw_capabilities, hw_capability_last);
switch (rev_id) {
- case JTAG_DEV_ID_MARLON_B0:
- wil->hw_name = "Marlon B0";
- wil->hw_version = HW_VER_MARLON_B0;
- break;
- case JTAG_DEV_ID_SPARROW_A0:
- wil->hw_name = "Sparrow A0";
- wil->hw_version = HW_VER_SPARROW_A0;
- break;
- case JTAG_DEV_ID_SPARROW_A1:
- wil->hw_name = "Sparrow A1";
- wil->hw_version = HW_VER_SPARROW_A1;
- break;
case JTAG_DEV_ID_SPARROW_B0:
wil->hw_name = "Sparrow B0";
wil->hw_version = HW_VER_SPARROW_B0;
@@ -62,13 +50,6 @@ void wil_set_capabilities(struct wil6210_priv *wil)
}
wil_info(wil, "Board hardware is %s\n", wil->hw_name);
-
- if (wil->hw_version >= HW_VER_SPARROW_A0)
- set_bit(hw_capability_reset_v2, wil->hw_capabilities);
-
- if (wil->hw_version >= HW_VER_SPARROW_B0)
- set_bit(hw_capability_advanced_itr_moderation,
- wil->hw_capabilities);
}
void wil_disable_irq(struct wil6210_priv *wil)
@@ -305,7 +286,6 @@ static void wil_pcie_remove(struct pci_dev *pdev)
}
static const struct pci_device_id wil6210_pcie_ids[] = {
- { PCI_DEVICE(0x1ae9, 0x0301) },
{ PCI_DEVICE(0x1ae9, 0x0310) },
{ PCI_DEVICE(0x1ae9, 0x0302) }, /* same as above, firmware broken */
{ /* end: all zeroes */ },
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index cfe43d2..97422e7 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -241,16 +241,10 @@ struct RGF_BL {
#define BIT_CAF_OSC_DIG_XTAL_STABLE BIT(0)
#define RGF_USER_JTAG_DEV_ID (0x880b34) /* device ID */
- #define JTAG_DEV_ID_MARLON_B0 (0x0612072f)
- #define JTAG_DEV_ID_SPARROW_A0 (0x0632072f)
- #define JTAG_DEV_ID_SPARROW_A1 (0x1632072f)
#define JTAG_DEV_ID_SPARROW_B0 (0x2632072f)
enum {
HW_VER_UNKNOWN,
- HW_VER_MARLON_B0, /* JTAG_DEV_ID_MARLON_B0 */
- HW_VER_SPARROW_A0, /* JTAG_DEV_ID_SPARROW_A0 */
- HW_VER_SPARROW_A1, /* JTAG_DEV_ID_SPARROW_A1 */
HW_VER_SPARROW_B0, /* JTAG_DEV_ID_SPARROW_B0 */
};
@@ -494,8 +488,6 @@ enum {
};
enum {
- hw_capability_reset_v2 = 0,
- hw_capability_advanced_itr_moderation = 1,
hw_capability_last
};
--
2.1.0
> Introduce boot loader. Instead of the operational firmware,
> very small boot loader is burned to the on-board flash. Boot loader
> initializes hardware upon reset, and prepares for low power mode.
> Boot loader reports MAC address and detects radio chip connected.
>
> Driver loads firmware only when bringing up interface. All information
> required to set up network interface, most important is MAC address,
> reported by the boot loader
>
> The firmware composed of 2 files:
> - wil6210.fw - firmware itself (compiled code + data)
> - wil6210.board - board file (various board and radio dependent
> calibrations and parameters)
>
> Signed-off-by: Vladimir Kondratiev <[email protected]>
Thanks, 8 patches applied to wireless-drivers-next.git:
2cd0f021b847 wil6210: boot loader
9a5511b58b25 wil6210: remove support for old hardware
e3351277ac58 wil6210: enable fix for HW bug in 802.11->803.3 transform
33c477fdab25 wil6210: branch prediction hints
0436fd9a2d1e wil6210: Change of threshold for tx vring idleness measurement
8f55cbec7f88 wil6210: Fix division by zero in wil_vring_debugfs_show
774974e50432 wil6210: rename 'secure_pcp' to 'privacy'
344a7024e01f wil6210: track privacy connection attribute
Kalle Valo
In the old hardware, bug existed that caused DA and SA for every
Rx packet to be swapped in the AP mode.
New hardware has fix for this bug. Enable this fix in the
hardware.
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/main.c | 4 ++++
drivers/net/wireless/ath/wil6210/txrx.c | 31 ------------------------------
drivers/net/wireless/ath/wil6210/wil6210.h | 7 +++++++
3 files changed, 11 insertions(+), 31 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 95755a5..db74e81 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -579,6 +579,10 @@ static int wil_target_reset(struct wil6210_priv *wil)
C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_RST_PWGD);
+ /* enable fix for HW bug related to the SA/DA swap in AP Rx */
+ S(RGF_DMA_OFUL_NID_0, BIT_DMA_OFUL_NID_0_RX_EXT_TR_EN |
+ BIT_DMA_OFUL_NID_0_RX_EXT_A3_SRC);
+
wil_dbg_misc(wil, "Reset completed in %d ms\n", delay * RST_DELAY);
return 0;
}
diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 8439f65..779d836 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -346,27 +346,6 @@ static void wil_rx_add_radiotap_header(struct wil6210_priv *wil,
}
}
-/*
- * Fast swap in place between 2 registers
- */
-static void wil_swap_u16(u16 *a, u16 *b)
-{
- *a ^= *b;
- *b ^= *a;
- *a ^= *b;
-}
-
-static void wil_swap_ethaddr(void *data)
-{
- struct ethhdr *eth = data;
- u16 *s = (u16 *)eth->h_source;
- u16 *d = (u16 *)eth->h_dest;
-
- wil_swap_u16(s++, d++);
- wil_swap_u16(s++, d++);
- wil_swap_u16(s, d);
-}
-
/**
* reap 1 frame from @swhead
*
@@ -386,7 +365,6 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
unsigned int sz = mtu_max + ETH_HLEN;
u16 dmalen;
u8 ftype;
- u8 ds_bits;
int cid;
struct wil_net_stats *stats;
@@ -474,15 +452,6 @@ static struct sk_buff *wil_vring_reap_rx(struct wil6210_priv *wil,
*/
}
- ds_bits = wil_rxdesc_ds_bits(d);
- if (ds_bits == 1) {
- /*
- * HW bug - in ToDS mode, i.e. Rx on AP side,
- * addresses get swapped
- */
- wil_swap_ethaddr(skb->data);
- }
-
return skb;
}
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 97422e7..85f0011 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -181,6 +181,13 @@ struct RGF_BL {
#define BIT_DMA_ITR_CNT_CRL_CLR BIT(3)
#define BIT_DMA_ITR_CNT_CRL_REACH_TRSH BIT(4)
+/* Offload control (Sparrow B0+) */
+#define RGF_DMA_OFUL_NID_0 (0x881cd4)
+ #define BIT_DMA_OFUL_NID_0_RX_EXT_TR_EN BIT(0)
+ #define BIT_DMA_OFUL_NID_0_TX_EXT_TR_EN BIT(1)
+ #define BIT_DMA_OFUL_NID_0_RX_EXT_A3_SRC BIT(2)
+ #define BIT_DMA_OFUL_NID_0_TX_EXT_A3_SRC BIT(3)
+
/* New (sparrow v2+) interrupt moderation control */
#define RGF_DMA_ITR_TX_DESQ_NO_MOD (0x881d40)
#define RGF_DMA_ITR_TX_CNT_TRSH (0x881d34)
--
2.1.0
Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.
Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader
The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
calibrations and parameters)
Signed-off-by: Vladimir Kondratiev <[email protected]>
---
drivers/net/wireless/ath/wil6210/debugfs.c | 2 +-
drivers/net/wireless/ath/wil6210/fw.c | 3 +-
drivers/net/wireless/ath/wil6210/fw_inc.c | 4 +-
drivers/net/wireless/ath/wil6210/main.c | 104 ++++++++++++++++++----------
drivers/net/wireless/ath/wil6210/pcie_bus.c | 2 +-
drivers/net/wireless/ath/wil6210/wil6210.h | 16 ++++-
drivers/net/wireless/ath/wil6210/wmi.c | 7 +-
7 files changed, 88 insertions(+), 50 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index 45c3558e..3ed16e7 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -549,7 +549,7 @@ static ssize_t wil_write_file_reset(struct file *file, const char __user *buf,
dev_close(ndev);
ndev->flags &= ~IFF_UP;
rtnl_unlock();
- wil_reset(wil);
+ wil_reset(wil, true);
return len;
}
diff --git a/drivers/net/wireless/ath/wil6210/fw.c b/drivers/net/wireless/ath/wil6210/fw.c
index 93c5cc1..4428345 100644
--- a/drivers/net/wireless/ath/wil6210/fw.c
+++ b/drivers/net/wireless/ath/wil6210/fw.c
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2014 Qualcomm Atheros, Inc.
+ * Copyright (c) 2014-2015 Qualcomm Atheros, Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
@@ -20,6 +20,7 @@
#include "fw.h"
MODULE_FIRMWARE(WIL_FW_NAME);
+MODULE_FIRMWARE(WIL_FW2_NAME);
/* target operations */
/* register read */
diff --git a/drivers/net/wireless/ath/wil6210/fw_inc.c b/drivers/net/wireless/ath/wil6210/fw_inc.c
index d4acf93..157f5ef 100644
--- a/drivers/net/wireless/ath/wil6210/fw_inc.c
+++ b/drivers/net/wireless/ath/wil6210/fw_inc.c
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2014 Qualcomm Atheros, Inc.
+ * Copyright (c) 2014-2015 Qualcomm Atheros, Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
@@ -451,8 +451,6 @@ static int wil_fw_load(struct wil6210_priv *wil, const void *data, size_t size)
}
return -EINVAL;
}
- /* Mark FW as loaded from host */
- S(RGF_USER_USAGE_6, 1);
return rc;
}
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index b04e0af..acbbd27 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -29,10 +29,6 @@ bool no_fw_recovery;
module_param(no_fw_recovery, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(no_fw_recovery, " disable automatic FW error recovery");
-static bool no_fw_load = true;
-module_param(no_fw_load, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(no_fw_load, " do not download FW, use one in on-card flash.");
-
/* if not set via modparam, will be set to default value of 1/8 of
* rx ring size during init flow
*/
@@ -532,6 +528,8 @@ static int wil_target_reset(struct wil6210_priv *wil)
wil_halt_cpu(wil);
+ /* clear all boot loader "ready" bits */
+ W(RGF_USER_BL + offsetof(struct RGF_BL, ready), 0);
/* Clear Fw Download notification */
C(RGF_USER_USAGE_6, BIT(0));
@@ -583,16 +581,16 @@ static int wil_target_reset(struct wil6210_priv *wil)
/* TODO: check order here!!! Erez code is different */
W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
- /* wait until device ready. typical time is 200..250 msec */
+ /* wait until device ready. typical time is 20..80 msec */
do {
msleep(RST_DELAY);
- x = R(RGF_USER_HW_MACHINE_STATE);
+ x = R(RGF_USER_BL + offsetof(struct RGF_BL, ready));
if (delay++ > RST_COUNT) {
- wil_err(wil, "Reset not completed, hw_state 0x%08x\n",
+ wil_err(wil, "Reset not completed, bl.ready 0x%08x\n",
x);
return -ETIME;
}
- } while (x != HW_MACHINE_BOOT_DONE);
+ } while (!(x & BIT_BL_READY));
if (!is_reset_v2)
W(RGF_PCIE_LOS_COUNTER_CTL, BIT(8));
@@ -603,11 +601,6 @@ static int wil_target_reset(struct wil6210_priv *wil)
return 0;
}
-#undef R
-#undef W
-#undef S
-#undef C
-
void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
{
le32_to_cpus(&r->base);
@@ -617,6 +610,32 @@ void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
le32_to_cpus(&r->head);
}
+static int wil_get_bl_info(struct wil6210_priv *wil)
+{
+ struct net_device *ndev = wil_to_ndev(wil);
+ struct RGF_BL bl;
+
+ wil_memcpy_fromio_32(&bl, wil->csr + HOSTADDR(RGF_USER_BL), sizeof(bl));
+ le32_to_cpus(&bl.ready);
+ le32_to_cpus(&bl.version);
+ le32_to_cpus(&bl.rf_type);
+ le32_to_cpus(&bl.baseband_type);
+
+ if (!is_valid_ether_addr(bl.mac_address)) {
+ wil_err(wil, "BL: Invalid MAC %pM\n", bl.mac_address);
+ return -EINVAL;
+ }
+
+ ether_addr_copy(ndev->perm_addr, bl.mac_address);
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ ether_addr_copy(ndev->dev_addr, bl.mac_address);
+ wil_info(wil,
+ "Boot Loader: ver = %d MAC = %pM RF = 0x%08x bband = 0x%08x\n",
+ bl.version, bl.mac_address, bl.rf_type, bl.baseband_type);
+
+ return 0;
+}
+
static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
{
ulong to = msecs_to_jiffies(1000);
@@ -637,7 +656,7 @@ static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
* After calling this routine, you're expected to reload
* the firmware.
*/
-int wil_reset(struct wil6210_priv *wil)
+int wil_reset(struct wil6210_priv *wil, bool load_fw)
{
int rc;
@@ -675,30 +694,36 @@ int wil_reset(struct wil6210_priv *wil)
if (rc)
return rc;
- if (!no_fw_load) {
- wil_info(wil, "Use firmware <%s>\n", WIL_FW_NAME);
+ rc = wil_get_bl_info(wil);
+ if (rc)
+ return rc;
+
+ if (load_fw) {
+ wil_info(wil, "Use firmware <%s> + board <%s>\n", WIL_FW_NAME,
+ WIL_FW2_NAME);
+
wil_halt_cpu(wil);
/* Loading f/w from the file */
rc = wil_request_firmware(wil, WIL_FW_NAME);
if (rc)
return rc;
+ rc = wil_request_firmware(wil, WIL_FW2_NAME);
+ if (rc)
+ return rc;
+
+ /* Mark FW as loaded from host */
+ S(RGF_USER_USAGE_6, 1);
- /* clear any interrupts which on-card-firmware may have set */
+ /* clear any interrupts which on-card-firmware
+ * may have set
+ */
wil6210_clear_irq(wil);
- { /* CAF_ICR - clear and mask */
- u32 a = HOSTADDR(RGF_CAF_ICR) +
- offsetof(struct RGF_ICR, ICR);
- u32 m = HOSTADDR(RGF_CAF_ICR) +
- offsetof(struct RGF_ICR, IMV);
- u32 icr = ioread32(wil->csr + a);
-
- iowrite32(icr, wil->csr + a); /* W1C */
- iowrite32(~0, wil->csr + m);
- wmb(); /* wait for completion */
- }
+ /* CAF_ICR - clear and mask */
+ /* it is W1C, clear by writing back same value */
+ S(RGF_CAF_ICR + offsetof(struct RGF_ICR, ICR), 0);
+ W(RGF_CAF_ICR + offsetof(struct RGF_ICR, IMV), ~0);
+
wil_release_cpu(wil);
- } else {
- wil_info(wil, "Use firmware from on-card flash\n");
}
/* init after reset */
@@ -706,15 +731,22 @@ int wil_reset(struct wil6210_priv *wil)
reinit_completion(&wil->wmi_ready);
reinit_completion(&wil->wmi_call);
- wil_configure_interrupt_moderation(wil);
- wil_unmask_irq(wil);
+ if (load_fw) {
+ wil_configure_interrupt_moderation(wil);
+ wil_unmask_irq(wil);
- /* we just started MAC, wait for FW ready */
- rc = wil_wait_for_fw_ready(wil);
+ /* we just started MAC, wait for FW ready */
+ rc = wil_wait_for_fw_ready(wil);
+ }
return rc;
}
+#undef R
+#undef W
+#undef S
+#undef C
+
void wil_fw_error_recovery(struct wil6210_priv *wil)
{
wil_dbg_misc(wil, "starting fw error recovery\n");
@@ -730,7 +762,7 @@ int __wil_up(struct wil6210_priv *wil)
WARN_ON(!mutex_is_locked(&wil->mutex));
- rc = wil_reset(wil);
+ rc = wil_reset(wil, true);
if (rc)
return rc;
@@ -837,7 +869,7 @@ int __wil_down(struct wil6210_priv *wil)
if (!iter)
wil_err(wil, "timeout waiting for idle FW/HW\n");
- wil_rx_fini(wil);
+ wil_reset(wil, false);
return 0;
}
diff --git a/drivers/net/wireless/ath/wil6210/pcie_bus.c b/drivers/net/wireless/ath/wil6210/pcie_bus.c
index 3dd2670..f7c165d 100644
--- a/drivers/net/wireless/ath/wil6210/pcie_bus.c
+++ b/drivers/net/wireless/ath/wil6210/pcie_bus.c
@@ -150,7 +150,7 @@ static int wil_if_pcie_enable(struct wil6210_priv *wil)
/* need reset here to obtain MAC */
mutex_lock(&wil->mutex);
- rc = wil_reset(wil);
+ rc = wil_reset(wil, false);
mutex_unlock(&wil->mutex);
if (debug_fw)
rc = 0;
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 9461156..cfe43d2 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -29,7 +29,8 @@ extern unsigned short rx_ring_overflow_thrsh;
extern int agg_wsize;
#define WIL_NAME "wil6210"
-#define WIL_FW_NAME "wil6210.fw"
+#define WIL_FW_NAME "wil6210.fw" /* code */
+#define WIL_FW2_NAME "wil6210.board" /* board & radio parameters */
#define WIL_MAX_BUS_REQUEST_KBPS 800000 /* ~6.1Gbps */
@@ -120,6 +121,16 @@ struct RGF_ICR {
u32 IMC; /* Mask Clear, write 1 to clear */
} __packed;
+struct RGF_BL {
+ u32 ready; /* 0x880A3C bit [0] */
+#define BIT_BL_READY BIT(0)
+ u32 version; /* 0x880A40 version of the BL struct */
+ u32 rf_type; /* 0x880A44 ID of the connected RF */
+ u32 baseband_type; /* 0x880A48 ID of the baseband */
+ u8 mac_address[ETH_ALEN]; /* 0x880A4C permanent MAC */
+ u8 pad[2];
+} __packed;
+
/* registers - FW addresses */
#define RGF_USER_USAGE_1 (0x880004)
#define RGF_USER_USAGE_6 (0x880018)
@@ -130,6 +141,7 @@ struct RGF_ICR {
#define RGF_USER_MAC_CPU_0 (0x8801fc)
#define BIT_USER_MAC_CPU_MAN_RST BIT(1) /* mac_cpu_man_rst */
#define RGF_USER_USER_SCRATCH_PAD (0x8802bc)
+#define RGF_USER_BL (0x880A3C) /* Boot Loader */
#define RGF_USER_FW_REV_ID (0x880a8c) /* chip revision */
#define RGF_USER_CLKS_CTL_0 (0x880abc)
#define BIT_USER_CLKS_CAR_AHB_SW_SEL BIT(1) /* ref clk/PLL */
@@ -658,7 +670,7 @@ int wil_if_add(struct wil6210_priv *wil);
void wil_if_remove(struct wil6210_priv *wil);
int wil_priv_init(struct wil6210_priv *wil);
void wil_priv_deinit(struct wil6210_priv *wil);
-int wil_reset(struct wil6210_priv *wil);
+int wil_reset(struct wil6210_priv *wil, bool no_fw);
void wil_fw_error_recovery(struct wil6210_priv *wil);
void wil_set_recovery_state(struct wil6210_priv *wil, int state);
int wil_up(struct wil6210_priv *wil);
diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c
index 0f3e433..e60186c 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.c
+++ b/drivers/net/wireless/ath/wil6210/wmi.c
@@ -281,7 +281,6 @@ int wmi_send(struct wil6210_priv *wil, u16 cmdid, void *buf, u16 len)
/*=== Event handlers ===*/
static void wmi_evt_ready(struct wil6210_priv *wil, int id, void *d, int len)
{
- struct net_device *ndev = wil_to_ndev(wil);
struct wireless_dev *wdev = wil->wdev;
struct wmi_ready_event *evt = d;
@@ -290,11 +289,7 @@ static void wmi_evt_ready(struct wil6210_priv *wil, int id, void *d, int len)
wil_info(wil, "FW ver. %d; MAC %pM; %d MID's\n", wil->fw_version,
evt->mac, wil->n_mids);
-
- if (!is_valid_ether_addr(ndev->dev_addr)) {
- memcpy(ndev->dev_addr, evt->mac, ETH_ALEN);
- memcpy(ndev->perm_addr, evt->mac, ETH_ALEN);
- }
+ /* ignore MAC address, we already have it from the boot loader */
snprintf(wdev->wiphy->fw_version, sizeof(wdev->wiphy->fw_version),
"%d", wil->fw_version);
}
--
2.1.0
Vladimir Kondratiev <[email protected]> writes:
> On Sunday, February 15, 2015 02:02:38 PM Vladimir Kondratiev wrote:
>> For the normal (non-sniffer) mode of operation, align Rx buffer
>> on 4*n+2, so IP header (after 14 bytes of Ethernet header)
>> will start dword aligned. This accelerated IP stack a little bit.
>>
>> Signed-off-by: Vladimir Kondratiev <[email protected]>
>>
> Kalle,
>
> please do not apply this patch. I found last minute problem with it -
> hardware is not always happy.
>
> For now, drop it please. I will do more testing and re-submit this
> patch if everything wends OK.
Ok, I dropped this patch. Patches 1-8 are still on my queue.
--
Kalle Valo