Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.
Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.
WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.
In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).
With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Manikanta Pubbisetty <[email protected]>
---
V2:
- Rebased on ToT
drivers/net/wireless/ath/ath11k/mac.c | 25 +++++++++++++++++++++++--
drivers/net/wireless/ath/ath11k/wmi.h | 4 ++++
2 files changed, 27 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index cad832e0e6b8..ce5a7a912a10 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3819,8 +3819,29 @@ static int ath11k_mac_op_hw_scan(struct ieee80211_hw *hw,
goto exit;
}
- for (i = 0; i < arg->num_chan; i++)
- arg->chan_list[i] = req->channels[i]->center_freq;
+ for (i = 0; i < arg->num_chan; i++) {
+ if (test_bit(WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL,
+ ar->ab->wmi_ab.svc_map)) {
+ arg->chan_list[i] =
+ u32_encode_bits(req->channels[i]->center_freq,
+ WMI_SCAN_CONF_PER_CH_CHANNEL_MASK);
+
+ /* If NL80211_SCAN_FLAG_COLOCATED_6GHZ is set in scan
+ * flags, then scan all PSC channels in 6 GHz band and
+ * those non-PSC channels where RNR IE is found during
+ * the legacy 2.4/5 GHz scan.
+ * If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set,
+ * then all channels in 6 GHz will be scanned.
+ */
+ if (req->channels[i]->band == NL80211_BAND_6GHZ &&
+ req->flags & NL80211_SCAN_FLAG_COLOCATED_6GHZ &&
+ !cfg80211_channel_is_psc(req->channels[i]))
+ arg->chan_list[i] |=
+ WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND;
+ } else {
+ arg->chan_list[i] = req->channels[i]->center_freq;
+ }
+ }
}
if (req->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) {
diff --git a/drivers/net/wireless/ath/ath11k/wmi.h b/drivers/net/wireless/ath/ath11k/wmi.h
index 63dbb085949f..584824e367db 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2097,6 +2097,7 @@ enum wmi_tlv_service {
/* The second 128 bits */
WMI_MAX_EXT_SERVICE = 256,
+ WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL = 265,
WMI_TLV_SERVICE_BIOS_SAR_SUPPORT = 326,
/* The third 128 bits */
@@ -3232,6 +3233,9 @@ struct wmi_start_scan_cmd {
#define WMI_SCAN_DWELL_MODE_SHIFT 21
#define WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE 0x00000800
+#define WMI_SCAN_CONF_PER_CH_CHANNEL_MASK GENMASK(19, 0)
+#define WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND BIT(20)
+
enum {
WMI_SCAN_DWELL_MODE_DEFAULT = 0,
WMI_SCAN_DWELL_MODE_CONSERVATIVE = 1,
base-commit: 1a304987a22c9f383f163f93beb47e89080d1cee
--
2.38.0
Manikanta Pubbisetty <[email protected]> wrote:
> Currently, time taken to scan all supported channels on WCN6750
> is ~8 seconds and connection time is almost 10 seconds. WCN6750
> supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
> channels for scan come around ~100 channels (default case).
> Since the chip doesn't have support for DBS (Dual Band Simultaneous),
> scans cannot be parallelized resulting in longer scan times.
>
> Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
> optimizing the scan for 6 GHz channels will bring down the overall
> scan time.
>
> WCN6750 firmware has support to scan a 6 GHz channel based on co-located
> AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
> results. When a scan request with all supported channel list is enqueued
> to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
> scan channel flag, firmware will scan only those 6 GHz channels for which
> RNR IEs are found in the legacy scan results.
>
> In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
> flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
> for non-PSC channels. Since there is high probability to find 6 GHz APs
> on PSC channels, these channels are always scanned. Only non-PSC channels
> are selectively scanned based on cached RNR information from the legacy
> scan results.
>
> If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
> then scan will happen on all supported channels (default behavior).
>
> With these optimizations, scan time is improved by 1.5-1.8 seconds on
> WCN6750. Similar savings have been observed on WCN6855.
>
> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
> Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
>
> Signed-off-by: Manikanta Pubbisetty <[email protected]>
Fails to apply, please rebase.
error: patch failed: drivers/net/wireless/ath/ath11k/wmi.h:2097
error: drivers/net/wireless/ath/ath11k/wmi.h: patch does not apply
stg import: Diff does not apply cleanly
Patch set to Changes Requested.
--
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
On 3/15/2023 3:59 PM, Kalle Valo wrote:
> Manikanta Pubbisetty <[email protected]> wrote:
>
>> Currently, time taken to scan all supported channels on WCN6750
>> is ~8 seconds and connection time is almost 10 seconds. WCN6750
>> supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
>> channels for scan come around ~100 channels (default case).
>> Since the chip doesn't have support for DBS (Dual Band Simultaneous),
>> scans cannot be parallelized resulting in longer scan times.
>>
>> Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
>> optimizing the scan for 6 GHz channels will bring down the overall
>> scan time.
>>
>> WCN6750 firmware has support to scan a 6 GHz channel based on co-located
>> AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
>> results. When a scan request with all supported channel list is enqueued
>> to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
>> scan channel flag, firmware will scan only those 6 GHz channels for which
>> RNR IEs are found in the legacy scan results.
>>
>> In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
>> flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
>> for non-PSC channels. Since there is high probability to find 6 GHz APs
>> on PSC channels, these channels are always scanned. Only non-PSC channels
>> are selectively scanned based on cached RNR information from the legacy
>> scan results.
>>
>> If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
>> then scan will happen on all supported channels (default behavior).
>>
>> With these optimizations, scan time is improved by 1.5-1.8 seconds on
>> WCN6750. Similar savings have been observed on WCN6855.
>>
>> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
>> Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
>>
>> Signed-off-by: Manikanta Pubbisetty <[email protected]>
>
> Fails to apply, please rebase.
>
> error: patch failed: drivers/net/wireless/ath/ath11k/wmi.h:2097
> error: drivers/net/wireless/ath/ath11k/wmi.h: patch does not apply
> stg import: Diff does not apply cleanly
>
> Patch set to Changes Requested.
I'll rebase the patch and send v3.
Thanks,
Manikanta