This patch adds a mac80211 based wireless driver for the rtl8187 USB
wireless card.
Signed-off-by: Michael Wu <[email protected]>
---
MAINTAINERS | 10
drivers/net/wireless/Kconfig | 2
drivers/net/wireless/Makefile | 3
drivers/net/wireless/rtl818x/Kconfig | 16 +
drivers/net/wireless/rtl818x/Makefile | 2
drivers/net/wireless/rtl818x/rtl8187.h | 125 ++++
drivers/net/wireless/rtl818x/rtl8187_dev.c | 730 ++++++++++++++++++++++++
drivers/net/wireless/rtl818x/rtl8187_rtl8225.c | 744 ++++++++++++++++++++++++
drivers/net/wireless/rtl818x/rtl8187_rtl8225.h | 30 +
drivers/net/wireless/rtl818x/rtl818x.h | 212 +++++++
10 files changed, 1874 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index b36923e..68f573d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2922,6 +2922,16 @@ S: Maintained
RISCOM8 DRIVER
S: Orphan
+RTL818X WIRELESS DRIVER
+P: Michael Wu
+M: [email protected]
+P: Andrea Merello
+M: [email protected]
+L: [email protected]
+W: http://linuxwireless.org/
+T: git kernel.org:/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git
+S: Maintained
+
S3 SAVAGE FRAMEBUFFER DRIVER
P: Antonino Daplas
M: [email protected]
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index c4b3dc2..3735c77 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -542,4 +542,6 @@ source "drivers/net/wireless/hostap/Kcon
source "drivers/net/wireless/bcm43xx/Kconfig"
source "drivers/net/wireless/zd1211rw/Kconfig"
+source "drivers/net/wireless/rtl818x/Kconfig"
+
endmenu
diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile
index d212460..198c992 100644
--- a/drivers/net/wireless/Makefile
+++ b/drivers/net/wireless/Makefile
@@ -44,3 +44,6 @@ obj-$(CONFIG_PCMCIA_WL3501) += wl3501_cs
obj-$(CONFIG_USB_ZD1201) += zd1201.o
obj-$(CONFIG_LIBERTAS_USB) += libertas/
+
+# Drivers using mac80211 stack (net/mac80211)
+obj-$(CONFIG_RTL818X) += rtl818x/
diff --git a/drivers/net/wireless/rtl818x/Kconfig b/drivers/net/wireless/rtl818x/Kconfig
new file mode 100644
index 0000000..e2c27f8
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/Kconfig
@@ -0,0 +1,16 @@
+config RTL818X
+ bool
+ default n
+
+config RTL8187
+ tristate "Realtek 8187 USB support"
+ depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL
+ select RTL818X
+ select EEPROM_93CX6
+ ---help---
+ This is a driver for RTL8187 based cards.
+ These are USB based chips found in cards such as:
+
+ Netgear WG111v2
+
+ Thanks to Realtek for their support!
diff --git a/drivers/net/wireless/rtl818x/Makefile b/drivers/net/wireless/rtl818x/Makefile
new file mode 100644
index 0000000..fe5dd6f
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/Makefile
@@ -0,0 +1,2 @@
+rtl8187-objs := rtl8187_dev.o rtl8187_rtl8225.o
+obj-$(CONFIG_RTL8187) += rtl8187.o
diff --git a/drivers/net/wireless/rtl818x/rtl8187.h b/drivers/net/wireless/rtl818x/rtl8187.h
new file mode 100644
index 0000000..bd0b6f9
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/rtl8187.h
@@ -0,0 +1,125 @@
+#ifndef RTL8187_H
+#define RTL8187_H
+
+#include "rtl818x.h"
+
+#define RTL8187_REQT_READ 0xC0
+#define RTL8187_REQT_WRITE 0x40
+#define RTL8187_REQ_GET_REG 0x05
+#define RTL8187_REQ_SET_REG 0x05
+
+#define RTL8187_MAX_RX 0x9C4
+
+struct rtl8187_rx_info {
+ struct urb *urb;
+ struct ieee80211_hw *dev;
+};
+
+struct rtl8187_rx_hdr {
+ __le16 len;
+ __le16 rate;
+ u8 noise;
+ u8 signal;
+ u8 agc;
+ u8 reserved;
+ __le64 mac_time;
+} __attribute__((packed));
+
+struct rtl8187_tx_info {
+ struct ieee80211_tx_control *control;
+ struct urb *urb;
+ struct ieee80211_hw *dev;
+};
+
+struct rtl8187_tx_hdr {
+ __le32 flags;
+#define RTL8187_TX_FLAG_NO_ENCRYPT (1 << 15)
+#define RTL8187_TX_FLAG_MORE_FRAG (1 << 17)
+#define RTL8187_TX_FLAG_CTS (1 << 18)
+#define RTL8187_TX_FLAG_RTS (1 << 23)
+ __le16 rts_duration;
+ __le16 len;
+ __le32 retry;
+} __attribute__((packed));
+
+struct rtl8187_priv {
+ /* common between rtl818x drivers */
+ struct rtl818x_csr *map;
+ void (*rf_init)(struct ieee80211_hw *);
+ int mode;
+
+ /* rtl8187 specific */
+ struct ieee80211_channel channels[14];
+ struct ieee80211_rate rates[12];
+ struct ieee80211_hw_mode modes[2];
+ struct usb_device *udev;
+ u8 *hwaddr;
+ u16 txpwr_base;
+ u8 asic_rev;
+ struct sk_buff_head rx_queue;
+};
+
+void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data);
+
+static inline u8 rtl818x_ioread8(struct rtl8187_priv *priv, u8 *addr)
+{
+ u8 val;
+
+ usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
+ RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
+ (unsigned long)addr, 0, &val, sizeof(val), HZ / 2);
+
+ return val;
+}
+
+static inline u16 rtl818x_ioread16(struct rtl8187_priv *priv, __le16 *addr)
+{
+ __le16 val;
+
+ usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
+ RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
+ (unsigned long)addr, 0, &val, sizeof(val), HZ / 2);
+
+ return le16_to_cpu(val);
+}
+
+static inline u32 rtl818x_ioread32(struct rtl8187_priv *priv, __le32 *addr)
+{
+ __le32 val;
+
+ usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0),
+ RTL8187_REQ_GET_REG, RTL8187_REQT_READ,
+ (unsigned long)addr, 0, &val, sizeof(val), HZ / 2);
+
+ return le32_to_cpu(val);
+}
+
+static inline void rtl818x_iowrite8(struct rtl8187_priv *priv,
+ u8 *addr, u8 val)
+{
+ usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
+ RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
+ (unsigned long)addr, 0, &val, sizeof(val), HZ / 2);
+}
+
+static inline void rtl818x_iowrite16(struct rtl8187_priv *priv,
+ __le16 *addr, u16 val)
+{
+ __le16 buf = cpu_to_le16(val);
+
+ usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
+ RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
+ (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2);
+}
+
+static inline void rtl818x_iowrite32(struct rtl8187_priv *priv,
+ __le32 *addr, u32 val)
+{
+ __le32 buf = cpu_to_le32(val);
+
+ usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
+ RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
+ (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2);
+}
+
+#endif /* RTL8187_H */
diff --git a/drivers/net/wireless/rtl818x/rtl8187_dev.c b/drivers/net/wireless/rtl818x/rtl8187_dev.c
new file mode 100644
index 0000000..8f9e781
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/rtl8187_dev.c
@@ -0,0 +1,730 @@
+
+/*
+ * Linux device driver for RTL8187
+ *
+ * Copyright 2007 Michael Wu <[email protected]>
+ * Copyright 2007 Andrea Merello <[email protected]>
+ *
+ * Based on the r8187 driver, which is:
+ * Copyright 2005 Andrea Merello <[email protected]>, et al.
+ *
+ * Thanks to Realtek for their support!
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/usb.h>
+#include <linux/delay.h>
+#include <linux/etherdevice.h>
+#include <linux/eeprom_93cx6.h>
+#include <net/mac80211.h>
+
+#include "rtl8187.h"
+#include "rtl8187_rtl8225.h"
+
+MODULE_AUTHOR("Michael Wu <[email protected]>");
+MODULE_AUTHOR("Andrea Merello <[email protected]>");
+MODULE_DESCRIPTION("RTL8187 USB wireless driver");
+MODULE_LICENSE("GPL");
+
+static struct usb_device_id rtl8187_table[] __devinitdata = {
+ /* Realtek */
+ {USB_DEVICE(0x0bda, 0x8187)},
+ /* Netgear */
+ {USB_DEVICE(0x0846, 0x6100)},
+ {USB_DEVICE(0x0846, 0x6a00)},
+ {}
+};
+
+MODULE_DEVICE_TABLE(usb, rtl8187_table);
+
+void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
+{
+ struct rtl8187_priv *priv = dev->priv;
+
+ data <<= 8;
+ data |= addr | 0x80;
+
+ rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF);
+ rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF);
+ rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF);
+ rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF);
+
+ mdelay(1);
+}
+
+static void rtl8187_tx_cb(struct urb *urb)
+{
+ struct ieee80211_tx_status status = { {0} };
+ struct sk_buff *skb = (struct sk_buff *)urb->context;
+ struct rtl8187_tx_info *info = (struct rtl8187_tx_info *)skb->cb;
+
+ usb_free_urb(info->urb);
+ if (info->control)
+ memcpy(&status.control, info->control, sizeof(status.control));
+ kfree(info->control);
+ skb_pull(skb, sizeof(struct rtl8187_tx_hdr));
+ status.flags |= IEEE80211_TX_STATUS_ACK;
+ ieee80211_tx_status_irqsafe(info->dev, skb, &status);
+}
+
+static int rtl8187_tx(struct ieee80211_hw *dev, struct sk_buff *skb,
+ struct ieee80211_tx_control *control)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ struct rtl8187_tx_hdr *hdr;
+ struct rtl8187_tx_info *info;
+ struct urb *urb;
+ u32 tmp;
+
+ urb = usb_alloc_urb(0, GFP_ATOMIC);
+ if (!urb) {
+ kfree_skb(skb);
+ return 0;
+ }
+
+ hdr = (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr));
+ tmp = skb->len - sizeof(*hdr);
+ tmp |= RTL8187_TX_FLAG_NO_ENCRYPT;
+ tmp |= control->rts_cts_rate << 19;
+ tmp |= control->tx_rate << 24;
+ if (ieee80211_get_morefrag((struct ieee80211_hdr *)skb))
+ tmp |= RTL8187_TX_FLAG_MORE_FRAG;
+ if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS) {
+ tmp |= RTL8187_TX_FLAG_RTS;
+ hdr->rts_duration =
+ ieee80211_rts_duration(dev, skb->len, control);
+ }
+ if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT)
+ tmp |= RTL8187_TX_FLAG_CTS;
+ hdr->flags = cpu_to_le32(tmp);
+ hdr->len = 0;
+ tmp = control->retry_limit << 8;
+ hdr->retry = cpu_to_le32(tmp);
+
+ info = (struct rtl8187_tx_info *)skb->cb;
+ info->control = kmemdup(control, sizeof(*control), GFP_ATOMIC);
+ info->urb = urb;
+ info->dev = dev;
+ usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, 2),
+ hdr, skb->len, rtl8187_tx_cb, skb);
+ usb_submit_urb(urb, GFP_ATOMIC);
+
+ return 0;
+}
+
+static void rtl8187_rx_cb(struct urb *urb)
+{
+ struct sk_buff *skb = (struct sk_buff *)urb->context;
+ struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb;
+ struct ieee80211_hw *dev = info->dev;
+ struct rtl8187_priv *priv = dev->priv;
+ struct rtl8187_rx_hdr *hdr;
+ struct ieee80211_rx_status rx_status = { 0 };
+ int rate, signal;
+
+ if (unlikely(urb->status)) {
+ info->urb = NULL;
+ usb_free_urb(urb);
+ return;
+ }
+
+ skb_unlink(skb, &priv->rx_queue);
+ skb_put(skb, urb->actual_length);
+ hdr = (struct rtl8187_rx_hdr *)(skb_tail_pointer(skb) - sizeof(*hdr));
+ skb_trim(skb, le16_to_cpu(hdr->len) & 0x0FFF);
+
+ signal = hdr->agc >> 1;
+ rate = (le16_to_cpu(hdr->rate) >> 4) & 0xF;
+ if (rate > 3) { /* OFDM rate */
+ if (signal > 90)
+ signal = 90;
+ else if (signal < 25)
+ signal = 25;
+ signal = 90 - signal;
+ } else { /* CCK rate */
+ if (signal > 95)
+ signal = 95;
+ else if (signal < 30)
+ signal = 30;
+ signal = 95 - signal;
+ }
+
+ rx_status.antenna = (hdr->signal >> 7) & 1;
+ rx_status.signal = 64 - min(hdr->noise, (u8)64);
+ rx_status.ssi = signal;
+ rx_status.rate = rate;
+ rx_status.freq = dev->conf.freq;
+ rx_status.channel = dev->conf.channel;
+ rx_status.phymode = dev->conf.phymode;
+ rx_status.mactime = le64_to_cpu(hdr->mac_time);
+ ieee80211_rx_irqsafe(dev, skb, &rx_status);
+
+ skb = dev_alloc_skb(RTL8187_MAX_RX);
+ if (unlikely(!skb)) {
+ usb_free_urb(urb);
+ /* TODO check rx queue length and refill *somewhere* */
+ return;
+ }
+
+ info = (struct rtl8187_rx_info *)skb->cb;
+ info->urb = urb;
+ info->dev = dev;
+ urb->transfer_buffer = skb_tail_pointer(skb);
+ urb->context = skb;
+ skb_queue_tail(&priv->rx_queue, skb);
+
+ usb_submit_urb(urb, GFP_ATOMIC);
+}
+
+static int rtl8187_init_urbs(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ struct urb *entry;
+ struct sk_buff *skb;
+ struct rtl8187_rx_info *info;
+
+ while (skb_queue_len(&priv->rx_queue) < 8) {
+ skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL);
+ if (!skb)
+ break;
+ entry = usb_alloc_urb(0, GFP_KERNEL);
+ if (!entry) {
+ kfree_skb(skb);
+ break;
+ }
+ usb_fill_bulk_urb(entry, priv->udev,
+ usb_rcvbulkpipe(priv->udev, 1),
+ skb_tail_pointer(skb),
+ RTL8187_MAX_RX, rtl8187_rx_cb, skb);
+ info = (struct rtl8187_rx_info *)skb->cb;
+ info->urb = entry;
+ info->dev = dev;
+ skb_queue_tail(&priv->rx_queue, skb);
+ usb_submit_urb(entry, GFP_KERNEL);
+ }
+
+ return 0;
+}
+
+static int rtl8187_init_hw(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u8 reg;
+ int i;
+
+ /* reset */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
+
+ mdelay(200);
+ rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10);
+ rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11);
+ rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00);
+ mdelay(200);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg &= (1 << 1);
+ reg |= RTL818X_CMD_RESET;
+ rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+
+ i = 10;
+ do {
+ mdelay(2);
+ if (!(rtl818x_ioread8(priv, &priv->map->CMD) &
+ RTL818X_CMD_RESET))
+ break;
+ } while (--i);
+
+ if (!i) {
+ printk(KERN_ERR "%s: Reset timeout!\n", wiphy_name(dev->wiphy));
+ return -ETIMEDOUT;
+ }
+
+ /* reload registers from eeprom */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
+
+ i = 10;
+ do {
+ mdelay(4);
+ if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) &
+ RTL818X_EEPROM_CMD_CONFIG))
+ break;
+ } while (--i);
+
+ if (!i) {
+ printk(KERN_ERR "%s: eeprom reset timeout!\n",
+ wiphy_name(dev->wiphy));
+ return -ETIMEDOUT;
+ }
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ /* setup card */
+ rtl818x_iowrite8(priv, (u8 *)0xFF85, 0);
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 0);
+
+ rtl818x_iowrite8(priv, (u8 *)0xFF85, 4);
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 1);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ for (i = 0; i < ETH_ALEN; i++)
+ rtl818x_iowrite8(priv, &priv->map->MAC[i], priv->hwaddr[i]);
+
+ rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
+ reg &= 0x3F;
+ reg |= 0x80;
+ rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg);
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
+ rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
+ rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81);
+
+ // TODO: set RESP_RATE and BRSR properly
+ rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
+
+ /* host_usb_init */
+ rtl818x_iowrite8(priv, (u8 *)0xFF85, 0);
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 0);
+ reg = rtl818x_ioread8(priv, (u8 *)0xFE53);
+ rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7));
+ rtl818x_iowrite8(priv, (u8 *)0xFF85, 4);
+ rtl818x_iowrite8(priv, &priv->map->GPIO, 0x20);
+ rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80);
+ mdelay(100);
+
+ rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
+ rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
+ mdelay(100);
+
+ priv->rf_init(dev);
+
+ rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
+ reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & 0xfffe;
+ rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 0x1);
+ rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
+ rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
+ rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
+ rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg);
+
+ return 0;
+}
+
+static void rtl8187_set_channel(struct ieee80211_hw *dev, int channel)
+{
+ u32 reg;
+ struct rtl8187_priv *priv = dev->priv;
+
+ reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
+ /* Enable TX loopback on MAC level to avoid TX during channel
+ * changes, as this has be seen to causes problems and the
+ * card will stop work until next reset
+ */
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF,
+ reg | RTL818X_TX_CONF_LOOPBACK_MAC);
+ mdelay(10);
+ rtl8225_rf_set_channel(dev, channel);
+ mdelay(10);
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
+}
+
+static int rtl8187_open(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u32 reg;
+ int ret;
+
+ ret = rtl8187_init_hw(dev);
+ if (ret)
+ return ret;
+
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
+
+ rtl8187_init_urbs(dev);
+
+ reg = RTL818X_RX_CONF_ONLYERLPKT |
+ RTL818X_RX_CONF_RX_AUTORESETPHY |
+ RTL818X_RX_CONF_BSSID |
+ RTL818X_RX_CONF_MGMT |
+ RTL818X_RX_CONF_CTRL |
+ RTL818X_RX_CONF_DATA |
+ (7 << 13 /* RX FIFO threshold NONE */) |
+ (7 << 10 /* MAX RX DMA */) |
+ RTL818X_RX_CONF_BROADCAST |
+ RTL818X_RX_CONF_MULTICAST |
+ RTL818X_RX_CONF_NICMAC;
+ if (priv->mode == IEEE80211_IF_TYPE_MNTR)
+ reg |= RTL818X_RX_CONF_MONITOR;
+
+ rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
+ reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT;
+ reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
+ rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
+
+ reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
+ reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT;
+ reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
+ reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
+ rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
+
+ reg = RTL818X_TX_CONF_CW_MIN |
+ (7 << 21 /* MAX TX DMA */) |
+ RTL818X_TX_CONF_NO_ICV;
+ rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg |= RTL818X_CMD_TX_ENABLE;
+ reg |= RTL818X_CMD_RX_ENABLE;
+ rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+
+ return 0;
+}
+
+static int rtl8187_stop(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ struct rtl8187_rx_info *info;
+ struct sk_buff *skb;
+ u32 reg;
+
+ rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
+
+ reg = rtl818x_ioread8(priv, &priv->map->CMD);
+ reg &= ~RTL818X_CMD_TX_ENABLE;
+ reg &= ~RTL818X_CMD_RX_ENABLE;
+ rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+
+ rtl8225_rf_stop(dev);
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ while ((skb = skb_dequeue(&priv->rx_queue))) {
+ info = (struct rtl8187_rx_info *)skb->cb;
+ if (!info->urb)
+ continue;
+
+ usb_kill_urb(info->urb);
+ kfree_skb(skb);
+ }
+ return 0;
+}
+
+static int rtl8187_add_interface(struct ieee80211_hw *dev,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct rtl8187_priv *priv = dev->priv;
+
+ /* NOTE: using IEEE80211_IF_TYPE_MGMT to indicate no mode selected */
+ if (priv->mode != IEEE80211_IF_TYPE_MGMT)
+ return -1;
+
+ switch (conf->type) {
+ case IEEE80211_IF_TYPE_STA:
+ case IEEE80211_IF_TYPE_MNTR:
+ priv->mode = conf->type;
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ priv->hwaddr = conf->mac_addr;
+
+ return 0;
+}
+
+static void rtl8187_remove_interface(struct ieee80211_hw *dev,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ priv->mode = IEEE80211_IF_TYPE_MGMT;
+}
+
+static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ rtl8187_set_channel(dev, conf->channel);
+
+ rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
+
+ if (conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME)
+ rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
+ else
+ rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
+
+ switch (conf->phymode) {
+ case MODE_IEEE80211B:
+ rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
+ rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24);
+ rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0xa5);
+ break;
+ case MODE_IEEE80211G:
+ rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
+ rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14);
+ rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0x73);
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
+ rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
+ rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
+ rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
+ return 0;
+}
+
+static int rtl8187_config_interface(struct ieee80211_hw *dev, int if_id,
+ struct ieee80211_if_conf *conf)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ int i;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]);
+
+ if (is_valid_ether_addr(conf->bssid))
+ rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_INFRA);
+ else
+ rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_NO_LINK);
+
+ return 0;
+}
+
+static const struct ieee80211_ops rtl8187_ops = {
+ .tx = rtl8187_tx,
+ .open = rtl8187_open,
+ .stop = rtl8187_stop,
+ .add_interface = rtl8187_add_interface,
+ .remove_interface = rtl8187_remove_interface,
+ .config = rtl8187_config,
+ .config_interface = rtl8187_config_interface,
+};
+
+static void rtl8187_register_read(struct eeprom_93cx6 *eeprom)
+{
+ struct ieee80211_hw *dev = eeprom->data;
+ struct rtl8187_priv *priv = dev->priv;
+ u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
+
+ eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
+ eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
+ eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
+ eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
+}
+
+static void rtl8187_register_write(struct eeprom_93cx6 *eeprom)
+{
+ struct ieee80211_hw *dev = eeprom->data;
+ struct rtl8187_priv *priv = dev->priv;
+ u8 reg = RTL818X_EEPROM_CMD_PROGRAM;
+
+ if (eeprom->reg_data_in)
+ reg |= RTL818X_EEPROM_CMD_WRITE;
+ if (eeprom->reg_data_out)
+ reg |= RTL818X_EEPROM_CMD_READ;
+ if (eeprom->reg_data_clock)
+ reg |= RTL818X_EEPROM_CMD_CK;
+ if (eeprom->reg_chip_select)
+ reg |= RTL818X_EEPROM_CMD_CS;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
+ udelay(10);
+}
+
+static int __devinit rtl8187_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
+{
+ struct usb_device *udev = interface_to_usbdev(intf);
+ struct ieee80211_hw *dev;
+ struct rtl8187_priv *priv;
+ struct eeprom_93cx6 eeprom;
+ struct ieee80211_channel *channel;
+ u16 txpwr, reg;
+ int err, i;
+
+ dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
+ if (!dev) {
+ printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n");
+ return -ENOMEM;
+ }
+
+ priv = dev->priv;
+
+ SET_IEEE80211_DEV(dev, &intf->dev);
+ usb_set_intfdata(intf, dev);
+ priv->udev = udev;
+
+ usb_get_dev(udev);
+
+ skb_queue_head_init(&priv->rx_queue);
+ memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
+ memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
+ priv->map = (struct rtl818x_csr *)0xFF00;
+ priv->modes[0].mode = MODE_IEEE80211G;
+ priv->modes[0].num_rates = ARRAY_SIZE(rtl818x_rates);
+ priv->modes[0].rates = priv->rates;
+ priv->modes[0].num_channels = ARRAY_SIZE(rtl818x_channels);
+ priv->modes[0].channels = priv->channels;
+ priv->modes[1].mode = MODE_IEEE80211B;
+ priv->modes[1].num_rates = 4;
+ priv->modes[1].rates = priv->rates;
+ priv->modes[1].num_channels = ARRAY_SIZE(rtl818x_channels);
+ priv->modes[1].channels = priv->channels;
+ priv->mode = IEEE80211_IF_TYPE_MGMT;
+ dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
+ IEEE80211_HW_RX_INCLUDES_FCS |
+ IEEE80211_HW_WEP_INCLUDE_IV |
+ IEEE80211_HW_DATA_NULLFUNC_ACK;
+ dev->extra_tx_headroom = sizeof(struct rtl8187_tx_hdr);
+ dev->queues = 1;
+ dev->max_rssi = 65;
+ dev->max_signal = 64;
+
+ for (i = 0; i < 2; i++)
+ if ((err = ieee80211_register_hwmode(dev, &priv->modes[i])))
+ goto err_free_dev;
+
+ eeprom.data = dev;
+ eeprom.register_read = rtl8187_register_read;
+ eeprom.register_write = rtl8187_register_write;
+ if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
+ eeprom.width = PCI_EEPROM_WIDTH_93C66;
+ else
+ eeprom.width = PCI_EEPROM_WIDTH_93C46;
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ udelay(10);
+
+ eeprom_93cx6_multiread(&eeprom, 0x7,
+ (__le16 __force *)dev->wiphy->perm_addr, 3);
+ if (!is_valid_ether_addr(dev->wiphy->perm_addr)) {
+ printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly generated MAC address\n");
+ random_ether_addr(dev->wiphy->perm_addr);
+ }
+
+ channel = priv->channels;
+ for (i = 0; i < 3; i++) {
+ eeprom_93cx6_read(&eeprom, 0x16 + i, &txpwr);
+ (*channel++).val = txpwr & 0xFF;
+ (*channel++).val = txpwr >> 8;
+ }
+ for (i = 0; i < 2; i++) {
+ eeprom_93cx6_read(&eeprom, 0x3D + i, &txpwr);
+ (*channel++).val = txpwr & 0xFF;
+ (*channel++).val = txpwr >> 8;
+ }
+ for (i = 0; i < 2; i++) {
+ eeprom_93cx6_read(&eeprom, 0x1B + i, &txpwr);
+ (*channel++).val = txpwr & 0xFF;
+ (*channel++).val = txpwr >> 8;
+ }
+
+ eeprom_93cx6_read(&eeprom, 0x05, &priv->txpwr_base);
+
+ reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & ~1;
+ rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 1);
+ /* 0 means asic B-cut, we should use SW 3 wire
+ * bit-by-bit banging for radio. 1 means we can use
+ * USB specific request to write radio registers */
+ priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
+ rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl8225_write(dev, 0, 0x1B7);
+
+ if (rtl8225_read(dev, 8) != 0x588 || rtl8225_read(dev, 9) != 0x700)
+ priv->rf_init = rtl8225_rf_init;
+ else
+ priv->rf_init = rtl8225z2_rf_init;
+
+ rtl8225_write(dev, 0, 0x0B7);
+
+ err = ieee80211_register_hw(dev);
+ if (err) {
+ printk(KERN_ERR "rtl8187: Cannot register device\n");
+ goto err_free_dev;
+ }
+
+ printk(KERN_INFO "%s: hwaddr " MAC_FMT ", rtl8187 V%d + %s\n",
+ wiphy_name(dev->wiphy), MAC_ARG(dev->wiphy->perm_addr),
+ priv->asic_rev, priv->rf_init == rtl8225_rf_init ?
+ "rtl8225" : "rtl8225z2");
+
+ return 0;
+
+ err_free_dev:
+ ieee80211_free_hw(dev);
+ usb_set_intfdata(intf, NULL);
+ usb_put_dev(udev);
+ return err;
+}
+
+static void __devexit rtl8187_disconnect(struct usb_interface *intf)
+{
+ struct ieee80211_hw *dev = usb_get_intfdata(intf);
+ struct rtl8187_priv *priv;
+
+ if (!dev)
+ return;
+
+ ieee80211_unregister_hw(dev);
+
+ priv = dev->priv;
+ usb_put_dev(interface_to_usbdev(intf));
+ ieee80211_free_hw(dev);
+}
+
+static struct usb_driver rtl8187_driver = {
+ .name = KBUILD_MODNAME,
+ .id_table = rtl8187_table,
+ .probe = rtl8187_probe,
+ .disconnect = rtl8187_disconnect,
+};
+
+static int __init rtl8187_init(void)
+{
+ return usb_register(&rtl8187_driver);
+}
+
+static void __exit rtl8187_exit(void)
+{
+ usb_deregister(&rtl8187_driver);
+}
+
+module_init(rtl8187_init);
+module_exit(rtl8187_exit);
diff --git a/drivers/net/wireless/rtl818x/rtl8187_rtl8225.c b/drivers/net/wireless/rtl818x/rtl8187_rtl8225.c
new file mode 100644
index 0000000..a89f023
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/rtl8187_rtl8225.c
@@ -0,0 +1,744 @@
+
+/*
+ * Radio tuning for RTL8225 on RTL8187
+ *
+ * Copyright 2007 Michael Wu <[email protected]>
+ * Copyright 2007 Andrea Merello <[email protected]>
+ *
+ * Based on the r8187 driver, which is:
+ * Copyright 2005 Andrea Merello <[email protected]>, et al.
+ *
+ * Thanks to Realtek for their support!
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/usb.h>
+#include <net/mac80211.h>
+
+#include "rtl8187.h"
+#include "rtl8187_rtl8225.h"
+
+static void rtl8225_write_bitbang(struct ieee80211_hw *dev, u8 addr, u16 data)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u16 reg80, reg84, reg82;
+ u32 bangdata;
+ int i;
+
+ bangdata = (data << 4) | (addr & 0xf);
+
+ reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput) & 0xfff3;
+ reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x7);
+
+ reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x7);
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80);
+ udelay(10);
+
+ for (i = 15; i >= 0; i--) {
+ u16 reg = reg80 | (bangdata & (1 << i)) >> i;
+
+ if (i & 1)
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1));
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1));
+
+ if (!(i & 1))
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84);
+ mdelay(2);
+}
+
+static void rtl8225_write_8051(struct ieee80211_hw *dev, u8 addr, u16 data)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u16 reg80, reg82, reg84;
+
+ reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput);
+ reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable);
+ reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect);
+
+ reg80 &= ~(0x3 << 2);
+ reg84 &= ~0xF;
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x0007);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x0007);
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ udelay(2);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80);
+ udelay(10);
+
+ usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0),
+ RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE,
+ addr, 0x8225, &data, sizeof(data), HZ / 2);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ udelay(10);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84);
+ mdelay(2);
+}
+
+void rtl8225_write(struct ieee80211_hw *dev, u8 addr, u16 data)
+{
+ struct rtl8187_priv *priv = dev->priv;
+
+ if (priv->asic_rev)
+ rtl8225_write_8051(dev, addr, data);
+ else
+ rtl8225_write_bitbang(dev, addr, data);
+}
+
+u16 rtl8225_read(struct ieee80211_hw *dev, u8 addr)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u16 reg80, reg82, reg84, out;
+ int i;
+
+ reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput);
+ reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable);
+ reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect);
+
+ reg80 &= ~0xF;
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x000F);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x000F);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2));
+ udelay(4);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80);
+ udelay(5);
+
+ for (i = 4; i >= 0; i--) {
+ u16 reg = reg80 | ((addr >> i) & 1);
+
+ if (!(i & 1)) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ udelay(1);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg | (1 << 1));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg | (1 << 1));
+ udelay(2);
+
+ if (i & 1) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg);
+ udelay(1);
+ }
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ udelay(2);
+
+ out = 0;
+ for (i = 11; i >= 0; i--) {
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ udelay(1);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ udelay(2);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 1));
+ udelay(2);
+
+ if (rtl818x_ioread16(priv, &priv->map->RFPinsInput) & (1 << 1))
+ out |= 1 << i;
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3));
+ udelay(2);
+ }
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput,
+ reg80 | (1 << 3) | (1 << 2));
+ udelay(2);
+
+ rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84);
+ rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x03A0);
+
+ return out;
+}
+
+static const u16 rtl8225bcd_rxgain[] = {
+ 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409,
+ 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541,
+ 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583,
+ 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644,
+ 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688,
+ 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745,
+ 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789,
+ 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793,
+ 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d,
+ 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9,
+ 0x07aa, 0x07ab, 0x07ac, 0x07ad, 0x07b0, 0x07b1, 0x07b2, 0x07b3,
+ 0x07b4, 0x07b5, 0x07b8, 0x07b9, 0x07ba, 0x07bb, 0x07bb
+};
+
+static const u8 rtl8225_agc[] = {
+ 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e,
+ 0x9d, 0x9c, 0x9b, 0x9a, 0x99, 0x98, 0x97, 0x96,
+ 0x95, 0x94, 0x93, 0x92, 0x91, 0x90, 0x8f, 0x8e,
+ 0x8d, 0x8c, 0x8b, 0x8a, 0x89, 0x88, 0x87, 0x86,
+ 0x85, 0x84, 0x83, 0x82, 0x81, 0x80, 0x3f, 0x3e,
+ 0x3d, 0x3c, 0x3b, 0x3a, 0x39, 0x38, 0x37, 0x36,
+ 0x35, 0x34, 0x33, 0x32, 0x31, 0x30, 0x2f, 0x2e,
+ 0x2d, 0x2c, 0x2b, 0x2a, 0x29, 0x28, 0x27, 0x26,
+ 0x25, 0x24, 0x23, 0x22, 0x21, 0x20, 0x1f, 0x1e,
+ 0x1d, 0x1c, 0x1b, 0x1a, 0x19, 0x18, 0x17, 0x16,
+ 0x15, 0x14, 0x13, 0x12, 0x11, 0x10, 0x0f, 0x0e,
+ 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08, 0x07, 0x06,
+ 0x05, 0x04, 0x03, 0x02, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01
+};
+
+static const u8 rtl8225_gain[] = {
+ 0x23, 0x88, 0x7c, 0xa5, /* -82dBm */
+ 0x23, 0x88, 0x7c, 0xb5, /* -82dBm */
+ 0x23, 0x88, 0x7c, 0xc5, /* -82dBm */
+ 0x33, 0x80, 0x79, 0xc5, /* -78dBm */
+ 0x43, 0x78, 0x76, 0xc5, /* -74dBm */
+ 0x53, 0x60, 0x73, 0xc5, /* -70dBm */
+ 0x63, 0x58, 0x70, 0xc5, /* -66dBm */
+};
+
+static const u8 rtl8225_threshold[] = {
+ 0x8d, 0x8d, 0x8d, 0x8d, 0x9d, 0xad, 0xbd
+};
+
+static const u8 rtl8225_tx_gain_cck_ofdm[] = {
+ 0x02, 0x06, 0x0e, 0x1e, 0x3e, 0x7e
+};
+
+static const u8 rtl8225_tx_power_cck[] = {
+ 0x18, 0x17, 0x15, 0x11, 0x0c, 0x08, 0x04, 0x02,
+ 0x1b, 0x1a, 0x17, 0x13, 0x0e, 0x09, 0x04, 0x02,
+ 0x1f, 0x1e, 0x1a, 0x15, 0x10, 0x0a, 0x05, 0x02,
+ 0x22, 0x21, 0x1d, 0x18, 0x11, 0x0b, 0x06, 0x02,
+ 0x26, 0x25, 0x21, 0x1b, 0x14, 0x0d, 0x06, 0x03,
+ 0x2b, 0x2a, 0x25, 0x1e, 0x16, 0x0e, 0x07, 0x03
+};
+
+static const u8 rtl8225_tx_power_cck_ch14[] = {
+ 0x18, 0x17, 0x15, 0x0c, 0x00, 0x00, 0x00, 0x00,
+ 0x1b, 0x1a, 0x17, 0x0e, 0x00, 0x00, 0x00, 0x00,
+ 0x1f, 0x1e, 0x1a, 0x0f, 0x00, 0x00, 0x00, 0x00,
+ 0x22, 0x21, 0x1d, 0x11, 0x00, 0x00, 0x00, 0x00,
+ 0x26, 0x25, 0x21, 0x13, 0x00, 0x00, 0x00, 0x00,
+ 0x2b, 0x2a, 0x25, 0x15, 0x00, 0x00, 0x00, 0x00
+};
+
+static const u8 rtl8225_tx_power_ofdm[] = {
+ 0x80, 0x90, 0xa2, 0xb5, 0xcb, 0xe4
+};
+
+static const u32 rtl8225_chan[] = {
+ 0x085c, 0x08dc, 0x095c, 0x09dc, 0x0a5c, 0x0adc, 0x0b5c,
+ 0x0bdc, 0x0c5c, 0x0cdc, 0x0d5c, 0x0ddc, 0x0e5c, 0x0f72
+};
+
+static void rtl8225_rf_set_tx_power(struct ieee80211_hw *dev, int channel)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u8 cck_power, ofdm_power;
+ const u8 *tmp;
+ u32 reg;
+ int i;
+
+ cck_power = priv->channels[channel - 1].val & 0xF;
+ ofdm_power = priv->channels[channel - 1].val >> 4;
+
+ cck_power = min(cck_power, (u8)11);
+ ofdm_power = min(ofdm_power, (u8)35);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK,
+ rtl8225_tx_gain_cck_ofdm[cck_power / 6] >> 1);
+
+ if (channel == 14)
+ tmp = &rtl8225_tx_power_cck_ch14[(cck_power % 6) * 8];
+ else
+ tmp = &rtl8225_tx_power_cck[(cck_power % 6) * 8];
+
+ for (i = 0; i < 8; i++)
+ rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++);
+
+ mdelay(1); // FIXME: optional?
+
+ /* anaparam2 on */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl8225_write_phy_ofdm(dev, 2, 0x42);
+ rtl8225_write_phy_ofdm(dev, 6, 0x00);
+ rtl8225_write_phy_ofdm(dev, 8, 0x00);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM,
+ rtl8225_tx_gain_cck_ofdm[ofdm_power / 6] >> 1);
+
+ tmp = &rtl8225_tx_power_ofdm[ofdm_power % 6];
+
+ rtl8225_write_phy_ofdm(dev, 5, *tmp);
+ rtl8225_write_phy_ofdm(dev, 7, *tmp);
+
+ mdelay(1);
+}
+
+void rtl8225_rf_init(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ int i;
+
+ rtl8225_write(dev, 0x0, 0x067); mdelay(1);
+ rtl8225_write(dev, 0x1, 0xFE0); mdelay(1);
+ rtl8225_write(dev, 0x2, 0x44D); mdelay(1);
+ rtl8225_write(dev, 0x3, 0x441); mdelay(1);
+ rtl8225_write(dev, 0x4, 0x486); mdelay(1);
+ rtl8225_write(dev, 0x5, 0xBC0); mdelay(1);
+ rtl8225_write(dev, 0x6, 0xAE6); mdelay(1);
+ rtl8225_write(dev, 0x7, 0x82A); mdelay(1);
+ rtl8225_write(dev, 0x8, 0x01F); mdelay(1);
+ rtl8225_write(dev, 0x9, 0x334); mdelay(1);
+ rtl8225_write(dev, 0xA, 0xFD4); mdelay(1);
+ rtl8225_write(dev, 0xB, 0x391); mdelay(1);
+ rtl8225_write(dev, 0xC, 0x050); mdelay(1);
+ rtl8225_write(dev, 0xD, 0x6DB); mdelay(1);
+ rtl8225_write(dev, 0xE, 0x029); mdelay(1);
+ rtl8225_write(dev, 0xF, 0x914); mdelay(100);
+
+ rtl8225_write(dev, 0x2, 0xC4D); mdelay(200);
+ rtl8225_write(dev, 0x2, 0x44D); mdelay(200);
+
+ if (!(rtl8225_read(dev, 6) & (1 << 7))) {
+ rtl8225_write(dev, 0x02, 0x0c4d);
+ mdelay(200);
+ rtl8225_write(dev, 0x02, 0x044d);
+ mdelay(100);
+ if (!(rtl8225_read(dev, 6) & (1 << 7)))
+ printk(KERN_WARNING "%s: RF Calibration Failed! %x\n",
+ wiphy_name(dev->wiphy), rtl8225_read(dev, 6));
+ }
+
+ rtl8225_write(dev, 0x0, 0x127);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225bcd_rxgain); i++) {
+ rtl8225_write(dev, 0x1, i + 1);
+ rtl8225_write(dev, 0x2, rtl8225bcd_rxgain[i]);
+ }
+
+ rtl8225_write(dev, 0x0, 0x027);
+ rtl8225_write(dev, 0x0, 0x22F);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) {
+ rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]);
+ mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i);
+ mdelay(1);
+ }
+
+ mdelay(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x00, 0x01); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x01, 0x02); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x02, 0x42); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x03, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x04, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x05, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x06, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x07, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x08, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0a, 0x09); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x10, 0x84); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x11, 0x06); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x12, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x13, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x14, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x15, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x16, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x17, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x18, 0xef); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x19, 0x19); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1b, 0x76); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x21, 0x27); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x22, 0x16); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x24, 0x46); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x25, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x27, 0x88); mdelay(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]);
+ rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]);
+ rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]);
+ rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]);
+
+ rtl8225_write_phy_cck(dev, 0x00, 0x98); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x03, 0x20); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x04, 0x7e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x05, 0x12); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x06, 0xfc); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x07, 0x78); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x08, 0x2e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x11, 0x88); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x12, 0x47); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x13, 0xd0);
+ rtl8225_write_phy_cck(dev, 0x19, 0x00);
+ rtl8225_write_phy_cck(dev, 0x1a, 0xa0);
+ rtl8225_write_phy_cck(dev, 0x1b, 0x08);
+ rtl8225_write_phy_cck(dev, 0x40, 0x86);
+ rtl8225_write_phy_cck(dev, 0x41, 0x8d); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x42, 0x15); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x43, 0x18); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x44, 0x1f); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x45, 0x1e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x46, 0x1a); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x47, 0x15); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x48, 0x10); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x49, 0x0a); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4a, 0x05); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4b, 0x02); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4c, 0x05); mdelay(1);
+
+ rtl818x_iowrite8(priv, &priv->map->TESTR, 0x0D);
+
+ rtl8225_rf_set_tx_power(dev, 1);
+
+ /* RX antenna default to A */
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); mdelay(1); /* B: 0xDB */
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); mdelay(1); /* B: 0x10 */
+
+ rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */
+ mdelay(1);
+ rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002);
+
+ /* set sensitivity */
+ rtl8225_write(dev, 0x0c, 0x50);
+ rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]);
+ rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]);
+ rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]);
+ rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]);
+ rtl8225_write_phy_cck(dev, 0x41, rtl8225_threshold[2]);
+}
+
+static const u8 rtl8225z2_tx_power_cck_ch14[] = {
+ 0x36, 0x35, 0x2e, 0x1b, 0x00, 0x00, 0x00, 0x00
+};
+
+static const u8 rtl8225z2_tx_power_cck[] = {
+ 0x36, 0x35, 0x2e, 0x25, 0x1c, 0x12, 0x09, 0x04
+};
+
+static const u8 rtl8225z2_tx_power_ofdm[] = {
+ 0x42, 0x00, 0x40, 0x00, 0x40
+};
+
+static const u8 rtl8225z2_tx_gain_cck_ofdm[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05,
+ 0x06, 0x07, 0x08, 0x09, 0x0a, 0x0b,
+ 0x0c, 0x0d, 0x0e, 0x0f, 0x10, 0x11,
+ 0x12, 0x13, 0x14, 0x15, 0x16, 0x17,
+ 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d,
+ 0x1e, 0x1f, 0x20, 0x21, 0x22, 0x23
+};
+
+static void rtl8225z2_rf_set_tx_power(struct ieee80211_hw *dev, int channel)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ u8 cck_power, ofdm_power;
+ const u8 *tmp;
+ u32 reg;
+ int i;
+
+ cck_power = priv->channels[channel - 1].val & 0xF;
+ ofdm_power = priv->channels[channel - 1].val >> 4;
+
+ cck_power = min(cck_power, (u8)15);
+ cck_power += priv->txpwr_base & 0xF;
+ cck_power = min(cck_power, (u8)35);
+
+ ofdm_power = min(ofdm_power, (u8)15);
+ ofdm_power += priv->txpwr_base >> 4;
+ ofdm_power = min(ofdm_power, (u8)35);
+
+ if (channel == 14)
+ tmp = rtl8225z2_tx_power_cck_ch14;
+ else
+ tmp = rtl8225z2_tx_power_cck;
+
+ for (i = 0; i < 8; i++)
+ rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK,
+ rtl8225z2_tx_gain_cck_ofdm[cck_power]);
+ mdelay(1);
+
+ /* anaparam2 on */
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+
+ rtl8225_write_phy_ofdm(dev, 2, 0x42);
+ rtl8225_write_phy_ofdm(dev, 5, 0x00);
+ rtl8225_write_phy_ofdm(dev, 6, 0x40);
+ rtl8225_write_phy_ofdm(dev, 7, 0x00);
+ rtl8225_write_phy_ofdm(dev, 8, 0x40);
+
+ rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM,
+ rtl8225z2_tx_gain_cck_ofdm[ofdm_power]);
+ mdelay(1);
+}
+
+static const u16 rtl8225z2_rxgain[] = {
+ 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409,
+ 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541,
+ 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583,
+ 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644,
+ 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688,
+ 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745,
+ 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789,
+ 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793,
+ 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d,
+ 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9,
+ 0x03aa, 0x03ab, 0x03ac, 0x03ad, 0x03b0, 0x03b1, 0x03b2, 0x03b3,
+ 0x03b4, 0x03b5, 0x03b8, 0x03b9, 0x03ba, 0x03bb, 0x03bb
+};
+
+static const u8 rtl8225z2_gain_bg[] = {
+ 0x23, 0x15, 0xa5, /* -82-1dBm */
+ 0x23, 0x15, 0xb5, /* -82-2dBm */
+ 0x23, 0x15, 0xc5, /* -82-3dBm */
+ 0x33, 0x15, 0xc5, /* -78dBm */
+ 0x43, 0x15, 0xc5, /* -74dBm */
+ 0x53, 0x15, 0xc5, /* -70dBm */
+ 0x63, 0x15, 0xc5 /* -66dBm */
+};
+
+void rtl8225z2_rf_init(struct ieee80211_hw *dev)
+{
+ struct rtl8187_priv *priv = dev->priv;
+ int i;
+
+ rtl8225_write(dev, 0x0, 0x2BF); mdelay(1);
+ rtl8225_write(dev, 0x1, 0xEE0); mdelay(1);
+ rtl8225_write(dev, 0x2, 0x44D); mdelay(1);
+ rtl8225_write(dev, 0x3, 0x441); mdelay(1);
+ rtl8225_write(dev, 0x4, 0x8C3); mdelay(1);
+ rtl8225_write(dev, 0x5, 0xC72); mdelay(1);
+ rtl8225_write(dev, 0x6, 0x0E6); mdelay(1);
+ rtl8225_write(dev, 0x7, 0x82A); mdelay(1);
+ rtl8225_write(dev, 0x8, 0x03F); mdelay(1);
+ rtl8225_write(dev, 0x9, 0x335); mdelay(1);
+ rtl8225_write(dev, 0xa, 0x9D4); mdelay(1);
+ rtl8225_write(dev, 0xb, 0x7BB); mdelay(1);
+ rtl8225_write(dev, 0xc, 0x850); mdelay(1);
+ rtl8225_write(dev, 0xd, 0xCDF); mdelay(1);
+ rtl8225_write(dev, 0xe, 0x02B); mdelay(1);
+ rtl8225_write(dev, 0xf, 0x114); mdelay(100);
+
+ rtl8225_write(dev, 0x0, 0x1B7);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225z2_rxgain); i++) {
+ rtl8225_write(dev, 0x1, i + 1);
+ rtl8225_write(dev, 0x2, rtl8225z2_rxgain[i]);
+ }
+
+ rtl8225_write(dev, 0x3, 0x080);
+ rtl8225_write(dev, 0x5, 0x004);
+ rtl8225_write(dev, 0x0, 0x0B7);
+ rtl8225_write(dev, 0x2, 0xc4D);
+
+ mdelay(200);
+ rtl8225_write(dev, 0x2, 0x44D);
+ mdelay(100);
+
+ if (!(rtl8225_read(dev, 6) & (1 << 7))) {
+ rtl8225_write(dev, 0x02, 0x0C4D);
+ mdelay(200);
+ rtl8225_write(dev, 0x02, 0x044D);
+ mdelay(100);
+ if (!(rtl8225_read(dev, 6) & (1 << 7)))
+ printk(KERN_WARNING "%s: RF Calibration Failed! %x\n",
+ wiphy_name(dev->wiphy), rtl8225_read(dev, 6));
+ }
+
+ mdelay(200);
+
+ rtl8225_write(dev, 0x0, 0x2BF);
+
+ for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) {
+ rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]);
+ mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i);
+ mdelay(1);
+ }
+
+ mdelay(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x00, 0x01); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x01, 0x02); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x02, 0x42); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x03, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x04, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x05, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x06, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x07, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x08, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0a, 0x08); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0d, 0x43);
+ rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x10, 0x84); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x11, 0x07); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x12, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x13, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x14, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x15, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x16, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x17, 0x40); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x18, 0xef); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x19, 0x19); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1b, 0x15); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1d, 0xc5); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x21, 0x17); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x22, 0x16); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x23, 0x80); mdelay(1); //FIXME: not needed?
+ rtl8225_write_phy_ofdm(dev, 0x24, 0x46); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x25, 0x00); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); mdelay(1);
+ rtl8225_write_phy_ofdm(dev, 0x27, 0x88); mdelay(1);
+
+ rtl8225_write_phy_ofdm(dev, 0x0b, rtl8225z2_gain_bg[4 * 3]);
+ rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225z2_gain_bg[4 * 3 + 1]);
+ rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225z2_gain_bg[4 * 3 + 2]);
+ rtl8225_write_phy_ofdm(dev, 0x21, 0x37);
+
+ rtl8225_write_phy_cck(dev, 0x00, 0x98); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x03, 0x20); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x04, 0x7e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x05, 0x12); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x06, 0xfc); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x07, 0x78); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x08, 0x2e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x11, 0x88); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x12, 0x47); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x13, 0xd0);
+ rtl8225_write_phy_cck(dev, 0x19, 0x00);
+ rtl8225_write_phy_cck(dev, 0x1a, 0xa0);
+ rtl8225_write_phy_cck(dev, 0x1b, 0x08);
+ rtl8225_write_phy_cck(dev, 0x40, 0x86);
+ rtl8225_write_phy_cck(dev, 0x41, 0x8d); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x42, 0x15); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x43, 0x18); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x44, 0x36); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x45, 0x35); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x46, 0x2e); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x47, 0x25); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x48, 0x1c); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x49, 0x12); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4a, 0x09); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4b, 0x04); mdelay(1);
+ rtl8225_write_phy_cck(dev, 0x4c, 0x05); mdelay(1);
+
+ rtl818x_iowrite8(priv, (u8 *)0xFF5B, 0x0D); mdelay(1);
+
+ rtl8225z2_rf_set_tx_power(dev, 1);
+
+ /* RX antenna default to A */
+ rtl8225_write_phy_cck(dev, 0x10, 0x9b); mdelay(1); /* B: 0xDB */
+ rtl8225_write_phy_ofdm(dev, 0x26, 0x90); mdelay(1); /* B: 0x10 */
+
+ rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */
+ mdelay(1);
+ rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002);
+}
+
+void rtl8225_rf_stop(struct ieee80211_hw *dev)
+{
+ u8 reg;
+ struct rtl8187_priv *priv = dev->priv;
+
+ rtl8225_write(dev, 0x4, 0x1f); mdelay(1);
+
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
+ reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_OFF);
+ rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_OFF);
+ rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
+ rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+}
+
+void rtl8225_rf_set_channel(struct ieee80211_hw *dev, int channel)
+{
+ struct rtl8187_priv *priv = dev->priv;
+
+ if (priv->rf_init == rtl8225_rf_init)
+ rtl8225_rf_set_tx_power(dev, channel);
+ else
+ rtl8225z2_rf_set_tx_power(dev, channel);
+
+ rtl8225_write(dev, 0x7, rtl8225_chan[channel - 1]);
+ mdelay(10);
+}
diff --git a/drivers/net/wireless/rtl818x/rtl8187_rtl8225.h b/drivers/net/wireless/rtl818x/rtl8187_rtl8225.h
new file mode 100644
index 0000000..ed28118
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/rtl8187_rtl8225.h
@@ -0,0 +1,30 @@
+#ifndef RTL8187_RTL8225_H
+#define RTL8187_RTL8225_H
+
+#define RTL8225_ANAPARAM_ON 0xa0000a59
+#define RTL8225_ANAPARAM2_ON 0x860c7312
+#define RTL8225_ANAPARAM_OFF 0xa00beb59
+#define RTL8225_ANAPARAM2_OFF 0x840dec11
+
+void rtl8225_write(struct ieee80211_hw *, u8 addr, u16 data);
+u16 rtl8225_read(struct ieee80211_hw *, u8 addr);
+
+void rtl8225_rf_init(struct ieee80211_hw *);
+void rtl8225z2_rf_init(struct ieee80211_hw *);
+void rtl8225_rf_stop(struct ieee80211_hw *);
+void rtl8225_rf_set_channel(struct ieee80211_hw *, int);
+
+
+static inline void rtl8225_write_phy_ofdm(struct ieee80211_hw *dev,
+ u8 addr, u32 data)
+{
+ rtl8187_write_phy(dev, addr, data);
+}
+
+static inline void rtl8225_write_phy_cck(struct ieee80211_hw *dev,
+ u8 addr, u32 data)
+{
+ rtl8187_write_phy(dev, addr, data | 0x10000);
+}
+
+#endif /* RTL8187_RTL8225_H */
diff --git a/drivers/net/wireless/rtl818x/rtl818x.h b/drivers/net/wireless/rtl818x/rtl818x.h
new file mode 100644
index 0000000..e4ee946
--- /dev/null
+++ b/drivers/net/wireless/rtl818x/rtl818x.h
@@ -0,0 +1,212 @@
+#ifndef RTL818X_H
+#define RTL818X_H
+
+struct rtl818x_csr {
+ u8 MAC[6];
+ u8 reserved_0[2];
+ __le32 MAR[2];
+ u8 RX_FIFO_COUNT;
+ u8 reserved_1;
+ u8 TX_FIFO_COUNT;
+ u8 BQREQ;
+ u8 reserved_2[4];
+ __le32 TSFT[2];
+ __le32 TLPDA;
+ __le32 TNPDA;
+ __le32 THPDA;
+ __le16 BRSR;
+ u8 BSSID[6];
+ u8 RESP_RATE;
+ u8 EIFS;
+ u8 reserved_3[1];
+ u8 CMD;
+#define RTL818X_CMD_TX_ENABLE (1 << 2)
+#define RTL818X_CMD_RX_ENABLE (1 << 3)
+#define RTL818X_CMD_RESET (1 << 4)
+ u8 reserved_4[4];
+ __le16 INT_MASK;
+ __le16 INT_STATUS;
+#define RTL818X_INT_RX_OK (1 << 0)
+#define RTL818X_INT_RX_ERR (1 << 1)
+#define RTL818X_INT_TXL_OK (1 << 2)
+#define RTL818X_INT_TXL_ERR (1 << 3)
+#define RTL818X_INT_RX_DU (1 << 4)
+#define RTL818X_INT_RX_FO (1 << 5)
+#define RTL818X_INT_TXN_OK (1 << 6)
+#define RTL818X_INT_TXN_ERR (1 << 7)
+#define RTL818X_INT_TXH_OK (1 << 8)
+#define RTL818X_INT_TXH_ERR (1 << 9)
+#define RTL818X_INT_TXB_OK (1 << 10)
+#define RTL818X_INT_TXB_ERR (1 << 11)
+#define RTL818X_INT_ATIM (1 << 12)
+#define RTL818X_INT_BEACON (1 << 13)
+#define RTL818X_INT_TIME_OUT (1 << 14)
+#define RTL818X_INT_TX_FO (1 << 15)
+ __le32 TX_CONF;
+#define RTL818X_TX_CONF_LOOPBACK_MAC (1 << 17)
+#define RTL818X_TX_CONF_NO_ICV (1 << 19)
+#define RTL818X_TX_CONF_DISCW (1 << 20)
+#define RTL818X_TX_CONF_R8180_ABCD (2 << 25)
+#define RTL818X_TX_CONF_R8180_F (3 << 25)
+#define RTL818X_TX_CONF_R8185_ABC (4 << 25)
+#define RTL818X_TX_CONF_R8185_D (5 << 25)
+#define RTL818X_TX_CONF_HWVER_MASK (7 << 25)
+#define RTL818X_TX_CONF_CW_MIN (1 << 31)
+ __le32 RX_CONF;
+#define RTL818X_RX_CONF_MONITOR (1 << 0)
+#define RTL818X_RX_CONF_NICMAC (1 << 1)
+#define RTL818X_RX_CONF_MULTICAST (1 << 2)
+#define RTL818X_RX_CONF_BROADCAST (1 << 3)
+#define RTL818X_RX_CONF_DATA (1 << 18)
+#define RTL818X_RX_CONF_CTRL (1 << 19)
+#define RTL818X_RX_CONF_MGMT (1 << 20)
+#define RTL818X_RX_CONF_BSSID (1 << 23)
+#define RTL818X_RX_CONF_RX_AUTORESETPHY (1 << 28)
+#define RTL818X_RX_CONF_ONLYERLPKT (1 << 31)
+ __le32 INT_TIMEOUT;
+ __le32 TBDA;
+ u8 EEPROM_CMD;
+#define RTL818X_EEPROM_CMD_READ (1 << 0)
+#define RTL818X_EEPROM_CMD_WRITE (1 << 1)
+#define RTL818X_EEPROM_CMD_CK (1 << 2)
+#define RTL818X_EEPROM_CMD_CS (1 << 3)
+#define RTL818X_EEPROM_CMD_NORMAL (0 << 6)
+#define RTL818X_EEPROM_CMD_LOAD (1 << 6)
+#define RTL818X_EEPROM_CMD_PROGRAM (2 << 6)
+#define RTL818X_EEPROM_CMD_CONFIG (3 << 6)
+ u8 CONFIG0;
+ u8 CONFIG1;
+ u8 CONFIG2;
+ __le32 ANAPARAM;
+ u8 MSR;
+#define RTL818X_MSR_NO_LINK (0 << 2)
+#define RTL818X_MSR_ADHOC (1 << 2)
+#define RTL818X_MSR_INFRA (2 << 2)
+ u8 CONFIG3;
+#define RTL818X_CONFIG3_ANAPARAM_WRITE (1 << 6)
+ u8 CONFIG4;
+#define RTL818X_CONFIG4_POWEROFF (1 << 6)
+#define RTL818X_CONFIG4_VCOOFF (1 << 7)
+ u8 TESTR;
+ u8 reserved_9[2];
+ __le16 PGSELECT;
+ __le32 ANAPARAM2;
+ u8 reserved_10[12];
+ __le16 BEACON_INTERVAL;
+ __le16 ATIM_WND;
+ __le16 BEACON_INTERVAL_TIME;
+ __le16 ATIMTR_INTERVAL;
+ u8 reserved_11[4];
+ u8 PHY[4];
+ __le16 RFPinsOutput;
+ __le16 RFPinsEnable;
+ __le16 RFPinsSelect;
+ __le16 RFPinsInput;
+ __le32 RF_PARA;
+ __le32 RF_TIMING;
+ u8 GP_ENABLE;
+ u8 GPIO;
+ u8 reserved_12[10];
+ u8 TX_AGC_CTL;
+#define RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT (1 << 0)
+#define RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT (1 << 1)
+#define RTL818X_TX_AGC_CTL_FEEDBACK_ANT (1 << 2)
+ u8 TX_GAIN_CCK;
+ u8 TX_GAIN_OFDM;
+ u8 TX_ANTENNA;
+ u8 reserved_13[16];
+ u8 WPA_CONF;
+ u8 reserved_14[3];
+ u8 SIFS;
+ u8 DIFS;
+ u8 SLOT;
+ u8 reserved_15[5];
+ u8 CW_CONF;
+#define RTL818X_CW_CONF_PERPACKET_CW_SHIFT (1 << 0)
+#define RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT (1 << 1)
+ u8 CW_VAL;
+ u8 RATE_FALLBACK;
+ u8 reserved_16[25];
+ u8 CONFIG5;
+ u8 TX_DMA_POLLING;
+ u8 reserved_17[2];
+ __le16 CWR;
+ u8 RETRY_CTR;
+ u8 reserved_18[5];
+ __le32 RDSAR;
+ u8 reserved_19[18];
+ u16 TALLY_CNT;
+ u8 TALLY_SEL;
+} __attribute__((packed));
+
+static const struct ieee80211_rate rtl818x_rates[] = {
+ { .rate = 10,
+ .val = 0,
+ .flags = IEEE80211_RATE_CCK },
+ { .rate = 20,
+ .val = 1,
+ .flags = IEEE80211_RATE_CCK },
+ { .rate = 55,
+ .val = 2,
+ .flags = IEEE80211_RATE_CCK },
+ { .rate = 110,
+ .val = 3,
+ .flags = IEEE80211_RATE_CCK },
+ { .rate = 60,
+ .val = 4,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 90,
+ .val = 5,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 120,
+ .val = 6,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 180,
+ .val = 7,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 240,
+ .val = 8,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 360,
+ .val = 9,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 480,
+ .val = 10,
+ .flags = IEEE80211_RATE_OFDM },
+ { .rate = 540,
+ .val = 11,
+ .flags = IEEE80211_RATE_OFDM },
+};
+
+static const struct ieee80211_channel rtl818x_channels[] = {
+ { .chan = 1,
+ .freq = 2412},
+ { .chan = 2,
+ .freq = 2417},
+ { .chan = 3,
+ .freq = 2422},
+ { .chan = 4,
+ .freq = 2427},
+ { .chan = 5,
+ .freq = 2432},
+ { .chan = 6,
+ .freq = 2437},
+ { .chan = 7,
+ .freq = 2442},
+ { .chan = 8,
+ .freq = 2447},
+ { .chan = 9,
+ .freq = 2452},
+ { .chan = 10,
+ .freq = 2457},
+ { .chan = 11,
+ .freq = 2462},
+ { .chan = 12,
+ .freq = 2467},
+ { .chan = 13,
+ .freq = 2472},
+ { .chan = 14,
+ .freq = 2484}
+};
+
+#endif /* RTL818X_H */
On Monday 07 May 2007 11:25, Jeff Garzik wrote:
> I am a bit skeptical that multiple files are needed. It seems like
> drivers/net/wireless/rtl818x.c would be a better path, a la tg3.c.
>
The radio tuning stuff could be stuffed into rtl8187_dev.c, but I like to keep
it separate since rtl8187_rtl8225.c tends to contain all the radio tuning
black magic that no one really understands except for the engineers at
Realtek, whereas rtl8187_dev.c is mostly straightforward. rtl8187 can also
(in theory) use another radio chip (rtl8255). The two headers - rtl818x.h and
rtl8187.h cannot be merged because the definitions in rtl818x.h are shared
between the usb and pci drivers.
I rather not combine any files, though I don't mind collapsing the driver
another level. However, I think other driver authors much prefer having their
own directory, and I'd like to keep the drivers consistently in their own
directory or all together in drivers/net/wireless.
-Michael Wu
On Monday 07 May 2007 19:25, David Miller wrote:
> I know this sounds trite, but when merging and researching up to 450
> patches at a time like I have to, this stuff starts to matter.
>
> Please put things as high in the directory hierachy as possible and
> when you can put the entire driver into a single source file do so.
>
Sure. I generally prefer that too, but all the drivers I put in wireless-dev
were put in separate directories because I didn't want to break the pattern.
> The only significant argument you present is the code sharing one for
> the radio stuff, but that isn't realized yet and you can certainly
> split the code out once you make that sharing a reality.
Having different modules for different radio chips really isn't the point of
keeping it in a separate file. (in fact, rtl8187_rtl8225.c actually contains
support for two versions of the rtl8225 radio) It's just that
rtl8187_rtl8225.c is basically a bunch of numbers with a bit of glue code to
send them to the hardware. Not much is missed if you decide not to look at
how the radio tuning works, and I like to avoid looking at that code if I
can. It's also consistent with how the (unreleased) rtl8180 driver works,
which really does have support for different radios in different files.
But of course, we can just make an exception for rtl8187. Would merging the
files together make that much of a difference for you?
-Michael Wu
Michael Wu wrote:
> This patch adds a mac80211 based wireless driver for the rtl8187 USB
> wireless card.
>
> Signed-off-by: Michael Wu <[email protected]>
> ---
>
> MAINTAINERS | 10
> drivers/net/wireless/Kconfig | 2
> drivers/net/wireless/Makefile | 3
> drivers/net/wireless/rtl818x/Kconfig | 16 +
> drivers/net/wireless/rtl818x/Makefile | 2
> drivers/net/wireless/rtl818x/rtl8187.h | 125 ++++
> drivers/net/wireless/rtl818x/rtl8187_dev.c | 730 ++++++++++++++++++++++++
> drivers/net/wireless/rtl818x/rtl8187_rtl8225.c | 744 ++++++++++++++++++++++++
> drivers/net/wireless/rtl818x/rtl8187_rtl8225.h | 30 +
> drivers/net/wireless/rtl818x/rtl818x.h | 212 +++++++
> 10 files changed, 1874 insertions(+), 0 deletions(-)
Much better.
For the record, new wireless drivers go TO John Linville for merging
(and he pushes to me, in turn).
I am a bit skeptical that multiple files are needed. It seems like
drivers/net/wireless/rtl818x.c would be a better path, a la tg3.c.
Jeff
From: Michael Wu <[email protected]>
Date: Mon, 7 May 2007 19:17:20 -0400
> On Monday 07 May 2007 11:25, Jeff Garzik wrote:
> > I am a bit skeptical that multiple files are needed. It seems like
> > drivers/net/wireless/rtl818x.c would be a better path, a la tg3.c.
> >
> The radio tuning stuff could be stuffed into rtl8187_dev.c, but I like to keep
> it separate since rtl8187_rtl8225.c tends to contain all the radio tuning
> black magic that no one really understands except for the engineers at
> Realtek, whereas rtl8187_dev.c is mostly straightforward. rtl8187 can also
> (in theory) use another radio chip (rtl8255). The two headers - rtl818x.h and
> rtl8187.h cannot be merged because the definitions in rtl818x.h are shared
> between the usb and pci drivers.
>
> I rather not combine any files, though I don't mind collapsing the driver
> another level. However, I think other driver authors much prefer having their
> own directory, and I'd like to keep the drivers consistently in their own
> directory or all together in drivers/net/wireless.
I certainly don't like it, sometimes I won't look at how e1000 (for
example) does things when researching a patch or some aspect of the
networking simply because I have to type in and TAB complete another
directory to get into where the driver's source file live.
I know this sounds trite, but when merging and researching up to 450
patches at a time like I have to, this stuff starts to matter.
Please put things as high in the directory hierachy as possible and
when you can put the entire driver into a single source file do so.
The only significant argument you present is the code sharing one for
the radio stuff, but that isn't realized yet and you can certainly
split the code out once you make that sharing a reality.