2008-07-04 03:34:47

by Daniel Drake

Subject: [PATCH] zd1211rw: beacon config error checking

Add some error checking to the new beacon configuration code.

Signed-off-by: Daniel Drake <[email protected]>

Index: linux-2.6.26-rc8/drivers/net/wireless/zd1211rw/zd_mac.c
===================================================================
--- linux-2.6.26-rc8.orig/drivers/net/wireless/zd1211rw/zd_mac.c
+++ linux-2.6.26-rc8/drivers/net/wireless/zd1211rw/zd_mac.c
@@ -475,43 +475,66 @@ static void cs_set_control(struct zd_mac
/* FIXME: Management frame? */
}

-void zd_mac_config_beacon(struct ieee80211_hw *hw, struct sk_buff *beacon)
+static int zd_mac_config_beacon(struct ieee80211_hw *hw, struct sk_buff *beacon)
{
struct zd_mac *mac = zd_hw_mac(hw);
+ int r;
u32 tmp, j = 0;
/* 4 more bytes for tail CRC */
u32 full_len = beacon->len + 4;
- zd_iowrite32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, 0);
- zd_ioread32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, &tmp);
+
+ r = zd_iowrite32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, 0);
+ if (r < 0)
+ return r;
+ r = zd_ioread32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, &tmp);
+ if (r < 0)
+ return r;
+
while (tmp & 0x2) {
- zd_ioread32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, &tmp);
+ r = zd_ioread32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, &tmp);
+ if (r < 0)
+ return r;
if ((++j % 100) == 0) {
printk(KERN_ERR "CR_BCN_FIFO_SEMAPHORE not ready\n");
if (j >= 500) {
printk(KERN_ERR "Giving up beacon config.\n");
- return;
+ return -ETIMEDOUT;
}
}
msleep(1);
}

- zd_iowrite32(&mac->chip, CR_BCN_FIFO, full_len - 1);
- if (zd_chip_is_zd1211b(&mac->chip))
- zd_iowrite32(&mac->chip, CR_BCN_LENGTH, full_len - 1);
+ r = zd_iowrite32(&mac->chip, CR_BCN_FIFO, full_len - 1);
+ if (r < 0)
+ return r;
+ if (zd_chip_is_zd1211b(&mac->chip)) {
+ r = zd_iowrite32(&mac->chip, CR_BCN_LENGTH, full_len - 1);
+ if (r < 0)
+ return r;
+ }

- for (j = 0 ; j < beacon->len; j++)
- zd_iowrite32(&mac->chip, CR_BCN_FIFO,
+ for (j = 0 ; j < beacon->len; j++) {
+ r = zd_iowrite32(&mac->chip, CR_BCN_FIFO,
*((u8 *)(beacon->data + j)));
+ if (r < 0)
+ return r;
+ }

- for (j = 0; j < 4; j++)
- zd_iowrite32(&mac->chip, CR_BCN_FIFO, 0x0);
+ for (j = 0; j < 4; j++) {
+ r = zd_iowrite32(&mac->chip, CR_BCN_FIFO, 0x0);
+ if (r < 0)
+ return r;
+ }
+
+ r = zd_iowrite32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, 1);
+ if (r < 0)
+ return r;

- zd_iowrite32(&mac->chip, CR_BCN_FIFO_SEMAPHORE, 1);
/* 802.11b/g 2.4G CCK 1Mb
* 802.11a, not yet implemented, uses different values (see GPL vendor
* driver)
*/
- zd_iowrite32(&mac->chip, CR_BCN_PLCP_CFG, 0x00000400 |
+ return zd_iowrite32(&mac->chip, CR_BCN_PLCP_CFG, 0x00000400 |
(full_len << 19));
}

@@ -780,14 +803,19 @@ static int zd_op_config_interface(struct
{
struct zd_mac *mac = zd_hw_mac(hw);
int associated;
+ int r;

if (mac->type == IEEE80211_IF_TYPE_MESH_POINT) {
associated = true;
if (conf->beacon) {
- zd_mac_config_beacon(hw, conf->beacon);
- kfree_skb(conf->beacon);
- zd_set_beacon_interval(&mac->chip, BCN_MODE_IBSS |
+ r = zd_mac_config_beacon(hw, conf->beacon);
+ if (r < 0)
+ return r;
+ r = zd_set_beacon_interval(&mac->chip, BCN_MODE_IBSS |
hw->conf.beacon_int);
+ if (r < 0)
+ return r;
+ kfree_skb(conf->beacon);
}
} else
associated = is_valid_ether_addr(conf->bssid);