* Read PCI-E infos offset from EEPROM and if it points to
serdes section (0x40), enable serdes programming (further
tweaking of serdes values during attach). This follows
Legacy and Sam's HAL sources.
---
drivers/net/wireless/ath/ath5k/attach.c | 56 +++++++++++++++++++------------
drivers/net/wireless/ath/ath5k/eeprom.c | 10 +++++
drivers/net/wireless/ath/ath5k/eeprom.h | 4 ++
3 files changed, 48 insertions(+), 22 deletions(-)
diff --git a/drivers/net/wireless/ath/ath5k/attach.c b/drivers/net/wireless/ath/ath5k/attach.c
index 9a84d94..6263065 100644
--- a/drivers/net/wireless/ath/ath5k/attach.c
+++ b/drivers/net/wireless/ath/ath5k/attach.c
@@ -253,28 +253,6 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
}
/*
- * Write PCI-E power save settings
- */
- if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) {
- ath5k_hw_reg_write(ah, 0x9248fc00, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x24924924, AR5K_PCIE_SERDES);
- /* Shut off RX when elecidle is asserted */
- ath5k_hw_reg_write(ah, 0x28000039, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x53160824, AR5K_PCIE_SERDES);
- /* TODO: EEPROM work */
- ath5k_hw_reg_write(ah, 0xe5980579, AR5K_PCIE_SERDES);
- /* Shut off PLL and CLKREQ active in L1 */
- ath5k_hw_reg_write(ah, 0x001defff, AR5K_PCIE_SERDES);
- /* Preserce other settings */
- ath5k_hw_reg_write(ah, 0x1aaabe40, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0xbe105554, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x000e3007, AR5K_PCIE_SERDES);
- /* Reset SERDES to load new settings */
- ath5k_hw_reg_write(ah, 0x00000000, AR5K_PCIE_SERDES_RESET);
- mdelay(1);
- }
-
- /*
* POST
*/
ret = ath5k_hw_post(ah);
@@ -295,6 +273,40 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
goto err_free;
}
+ /*
+ * Write PCI-E power save settings
+ */
+ if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) {
+ struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
+
+ ath5k_hw_reg_write(ah, 0x9248fc00, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x24924924, AR5K_PCIE_SERDES);
+
+ /* Shut off RX when elecidle is asserted */
+ ath5k_hw_reg_write(ah, 0x28000039, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x53160824, AR5K_PCIE_SERDES);
+
+ /* If serdes programing is enabled, increase PCI-E
+ * tx power for systems with long trace from host
+ * to minicard connector. */
+ if (ee->ee_serdes)
+ ath5k_hw_reg_write(ah, 0xe5980579, AR5K_PCIE_SERDES);
+ else
+ ath5k_hw_reg_write(ah, 0xf6800579, AR5K_PCIE_SERDES);
+
+ /* Shut off PLL and CLKREQ active in L1 */
+ ath5k_hw_reg_write(ah, 0x001defff, AR5K_PCIE_SERDES);
+
+ /* Preserve other settings */
+ ath5k_hw_reg_write(ah, 0x1aaabe40, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0xbe105554, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x000e3007, AR5K_PCIE_SERDES);
+
+ /* Reset SERDES to load new settings */
+ ath5k_hw_reg_write(ah, 0x00000000, AR5K_PCIE_SERDES_RESET);
+ mdelay(1);
+ }
+
/* Get misc capabilities */
ret = ath5k_hw_set_capabilities(ah);
if (ret) {
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index c56b494..8af477d 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -167,6 +167,16 @@ ath5k_eeprom_init_header(struct ath5k_hw *ah)
ee->ee_rfkill_pin = (u8) AR5K_REG_MS(val, AR5K_EEPROM_RFKILL_GPIO_SEL);
ee->ee_rfkill_pol = val & AR5K_EEPROM_RFKILL_POLARITY ? true : false;
+ /* Check if PCIE_OFFSET points to PCIE_SERDES_SECTION
+ * and enable serdes programming if needed.
+ *
+ * XXX: Serdes values seem to be fixed so
+ * no need to read them here, we write them
+ * during ath5k_hw_attach */
+ AR5K_EEPROM_READ(AR5K_EEPROM_PCIE_OFFSET, val);
+ ee->ee_serdes = (val == AR5K_EEPROM_PCIE_SERDES_SECTION) ?
+ true : false;
+
return 0;
}
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.h b/drivers/net/wireless/ath/ath5k/eeprom.h
index 64be73a..0123f35 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.h
+++ b/drivers/net/wireless/ath/ath5k/eeprom.h
@@ -19,6 +19,9 @@
/*
* Common ar5xxx EEPROM data offsets (set these on AR5K_EEPROM_BASE)
*/
+#define AR5K_EEPROM_PCIE_OFFSET 0x02 /* Contains offset to PCI-E infos */
+#define AR5K_EEPROM_PCIE_SERDES_SECTION 0x40 /* PCIE_OFFSET points here when
+ * SERDES infos are present */
#define AR5K_EEPROM_MAGIC 0x003d /* EEPROM Magic number */
#define AR5K_EEPROM_MAGIC_VALUE 0x5aa5 /* Default - found on EEPROM */
#define AR5K_EEPROM_MAGIC_5212 0x0000145c /* 5212 */
@@ -391,6 +394,7 @@ struct ath5k_eeprom_info {
u8 ee_rfkill_pin;
bool ee_rfkill_pol;
bool ee_is_hb63;
+ bool ee_serdes;
u16 ee_misc0;
u16 ee_misc1;
u16 ee_misc2;
* Read PCI-E infos offset from EEPROM and if it points to
serdes section (0x40), enable serdes programming (further
tweaking of serdes values during attach). This follows
Legacy and Sam's HAL sources.
Signed-off-by: Nick Kossifidis <[email protected]>
---
drivers/net/wireless/ath/ath5k/attach.c | 56 +++++++++++++++++++------------
drivers/net/wireless/ath/ath5k/eeprom.c | 10 +++++
drivers/net/wireless/ath/ath5k/eeprom.h | 4 ++
3 files changed, 48 insertions(+), 22 deletions(-)
diff --git a/drivers/net/wireless/ath/ath5k/attach.c b/drivers/net/wireless/ath/ath5k/attach.c
index 9a84d94..6263065 100644
--- a/drivers/net/wireless/ath/ath5k/attach.c
+++ b/drivers/net/wireless/ath/ath5k/attach.c
@@ -253,28 +253,6 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
}
/*
- * Write PCI-E power save settings
- */
- if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) {
- ath5k_hw_reg_write(ah, 0x9248fc00, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x24924924, AR5K_PCIE_SERDES);
- /* Shut off RX when elecidle is asserted */
- ath5k_hw_reg_write(ah, 0x28000039, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x53160824, AR5K_PCIE_SERDES);
- /* TODO: EEPROM work */
- ath5k_hw_reg_write(ah, 0xe5980579, AR5K_PCIE_SERDES);
- /* Shut off PLL and CLKREQ active in L1 */
- ath5k_hw_reg_write(ah, 0x001defff, AR5K_PCIE_SERDES);
- /* Preserce other settings */
- ath5k_hw_reg_write(ah, 0x1aaabe40, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0xbe105554, AR5K_PCIE_SERDES);
- ath5k_hw_reg_write(ah, 0x000e3007, AR5K_PCIE_SERDES);
- /* Reset SERDES to load new settings */
- ath5k_hw_reg_write(ah, 0x00000000, AR5K_PCIE_SERDES_RESET);
- mdelay(1);
- }
-
- /*
* POST
*/
ret = ath5k_hw_post(ah);
@@ -295,6 +273,40 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
goto err_free;
}
+ /*
+ * Write PCI-E power save settings
+ */
+ if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) {
+ struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
+
+ ath5k_hw_reg_write(ah, 0x9248fc00, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x24924924, AR5K_PCIE_SERDES);
+
+ /* Shut off RX when elecidle is asserted */
+ ath5k_hw_reg_write(ah, 0x28000039, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x53160824, AR5K_PCIE_SERDES);
+
+ /* If serdes programing is enabled, increase PCI-E
+ * tx power for systems with long trace from host
+ * to minicard connector. */
+ if (ee->ee_serdes)
+ ath5k_hw_reg_write(ah, 0xe5980579, AR5K_PCIE_SERDES);
+ else
+ ath5k_hw_reg_write(ah, 0xf6800579, AR5K_PCIE_SERDES);
+
+ /* Shut off PLL and CLKREQ active in L1 */
+ ath5k_hw_reg_write(ah, 0x001defff, AR5K_PCIE_SERDES);
+
+ /* Preserve other settings */
+ ath5k_hw_reg_write(ah, 0x1aaabe40, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0xbe105554, AR5K_PCIE_SERDES);
+ ath5k_hw_reg_write(ah, 0x000e3007, AR5K_PCIE_SERDES);
+
+ /* Reset SERDES to load new settings */
+ ath5k_hw_reg_write(ah, 0x00000000, AR5K_PCIE_SERDES_RESET);
+ mdelay(1);
+ }
+
/* Get misc capabilities */
ret = ath5k_hw_set_capabilities(ah);
if (ret) {
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index c56b494..8af477d 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -167,6 +167,16 @@ ath5k_eeprom_init_header(struct ath5k_hw *ah)
ee->ee_rfkill_pin = (u8) AR5K_REG_MS(val, AR5K_EEPROM_RFKILL_GPIO_SEL);
ee->ee_rfkill_pol = val & AR5K_EEPROM_RFKILL_POLARITY ? true : false;
+ /* Check if PCIE_OFFSET points to PCIE_SERDES_SECTION
+ * and enable serdes programming if needed.
+ *
+ * XXX: Serdes values seem to be fixed so
+ * no need to read them here, we write them
+ * during ath5k_hw_attach */
+ AR5K_EEPROM_READ(AR5K_EEPROM_PCIE_OFFSET, val);
+ ee->ee_serdes = (val == AR5K_EEPROM_PCIE_SERDES_SECTION) ?
+ true : false;
+
return 0;
}
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.h b/drivers/net/wireless/ath/ath5k/eeprom.h
index 64be73a..0123f35 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.h
+++ b/drivers/net/wireless/ath/ath5k/eeprom.h
@@ -19,6 +19,9 @@
/*
* Common ar5xxx EEPROM data offsets (set these on AR5K_EEPROM_BASE)
*/
+#define AR5K_EEPROM_PCIE_OFFSET 0x02 /* Contains offset to PCI-E infos */
+#define AR5K_EEPROM_PCIE_SERDES_SECTION 0x40 /* PCIE_OFFSET points here when
+ * SERDES infos are present */
#define AR5K_EEPROM_MAGIC 0x003d /* EEPROM Magic number */
#define AR5K_EEPROM_MAGIC_VALUE 0x5aa5 /* Default - found on EEPROM */
#define AR5K_EEPROM_MAGIC_5212 0x0000145c /* 5212 */
@@ -391,6 +394,7 @@ struct ath5k_eeprom_info {
u8 ee_rfkill_pin;
bool ee_rfkill_pol;
bool ee_is_hb63;
+ bool ee_serdes;
u16 ee_misc0;
u16 ee_misc1;
u16 ee_misc2;