Realtek devices with designation RTL8188CE-VL have the so-called B-cut
of the wireless chip. This patch adds the special programming needed by
these devices.
Signed-off-by: Larry Finger <[email protected]>
Cc: Anisse Astier <[email protected]>
Cc: Li Chaoming <[email protected]>
---
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c | 21 +++++++
drivers/net/wireless/rtlwifi/rtl8192ce/def.h | 3 +
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c | 61 ++++++++++++++++++--
drivers/net/wireless/rtlwifi/rtl8192ce/phy.c | 4 +-
drivers/net/wireless/rtlwifi/rtl8192ce/sw.c | 6 +-
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c | 4 +-
6 files changed, 87 insertions(+), 12 deletions(-)
---
V1 => V2 Remove extraneous white space.
John,
This patch is too invasive to backport to the stable kernels, thus it should
be applied to 3.7.
Thanks,
Larry
---
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c
@@ -724,6 +724,26 @@ u8 rtl92c_phy_sw_chnl(struct ieee80211_h
}
EXPORT_SYMBOL(rtl92c_phy_sw_chnl);
+static void _rtl92c_phy_sw_rf_setting(struct ieee80211_hw *hw, u8 channel)
+{
+ struct rtl_priv *rtlpriv = rtl_priv(hw);
+ struct rtl_phy *rtlphy = &(rtlpriv->phy);
+ struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
+
+ if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version)) {
+ if (channel == 6 && rtlphy->current_chan_bw ==
+ HT_CHANNEL_WIDTH_20)
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G1, MASKDWORD,
+ 0x00255);
+ else{
+ u32 backupRF0x1A = (u32)rtl_get_rfreg(hw, RF90_PATH_A,
+ RF_RX_G1, RFREG_OFFSET_MASK);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G1, MASKDWORD,
+ backupRF0x1A);
+ }
+ }
+}
+
static bool _rtl92c_phy_set_sw_chnl_cmdarray(struct swchnlcmd *cmdtable,
u32 cmdtableidx, u32 cmdtablesz,
enum swchnlcmd_id cmdid,
@@ -837,6 +857,7 @@ bool _rtl92c_phy_sw_chnl_step_by_step(st
currentcmd->para1,
RFREG_OFFSET_MASK,
rtlphy->rfreg_chnlval[rfpath]);
+ _rtl92c_phy_sw_rf_setting(hw, channel);
}
break;
default:
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/def.h
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/def.h
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/def.h
@@ -116,6 +116,9 @@
LE_BITS_TO_4BYTE(((__pcmdfbhdr) + 4), 20, 12)
#define CHIP_VER_B BIT(4)
+#define CHIP_BONDING_IDENTIFIER(_value) (((_value) >> 22) & 0x3)
+#define CHIP_BONDING_92C_1T2R 0x1
+#define RF_TYPE_1T2R BIT(1)
#define CHIP_92C_BITMASK BIT(0)
#define CHIP_UNKNOWN BIT(7)
#define CHIP_92C_1T2R 0x03
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
@@ -896,7 +896,6 @@ int rtl92ce_hw_init(struct ieee80211_hw
struct rtl_phy *rtlphy = &(rtlpriv->phy);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
- static bool iqk_initialized; /* initialized to false */
bool rtstatus = true;
bool is92c;
int err;
@@ -921,9 +920,28 @@ int rtl92ce_hw_init(struct ieee80211_hw
rtlhal->last_hmeboxnum = 0;
rtl92c_phy_mac_config(hw);
+ /* because last function modify RCR, so we update
+ * rcr var here, or TP will unstable for receive_config
+ * is wrong, RX RCR_ACRC32 will cause TP unstabel & Rx
+ * RCR_APP_ICV will cause mac80211 unassoc for cisco 1252*/
+ rtlpci->receive_config = rtl_read_dword(rtlpriv, REG_RCR);
+ rtlpci->receive_config &= ~(RCR_ACRC32 | RCR_AICV);
+ rtl_write_dword(rtlpriv, REG_RCR, rtlpci->receive_config);
rtl92c_phy_bb_config(hw);
rtlphy->rf_mode = RF_OP_BY_SW_3WIRE;
rtl92c_phy_rf_config(hw);
+ if (IS_VENDOR_UMC_A_CUT(rtlhal->version) &&
+ !IS_92C_SERIAL(rtlhal->version)) {
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G1, MASKDWORD, 0x30255);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G2, MASKDWORD, 0x50a00);
+ } else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version)) {
+ rtl_set_rfreg(hw, RF90_PATH_A, 0x0C, MASKDWORD, 0x894AE);
+ rtl_set_rfreg(hw, RF90_PATH_A, 0x0A, MASKDWORD, 0x1AF31);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_IPA, MASKDWORD, 0x8F425);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_SYN_G2, MASKDWORD, 0x4F200);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK1, MASKDWORD, 0x44053);
+ rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK2, MASKDWORD, 0x80201);
+ }
rtlphy->rfreg_chnlval[0] = rtl_get_rfreg(hw, (enum radio_path)0,
RF_CHNLBW, RFREG_OFFSET_MASK);
rtlphy->rfreg_chnlval[1] = rtl_get_rfreg(hw, (enum radio_path)1,
@@ -945,11 +963,11 @@ int rtl92ce_hw_init(struct ieee80211_hw
if (ppsc->rfpwr_state == ERFON) {
rtl92c_phy_set_rfpath_switch(hw, 1);
- if (iqk_initialized) {
+ if (rtlphy->iqk_initialized) {
rtl92c_phy_iq_calibrate(hw, true);
} else {
rtl92c_phy_iq_calibrate(hw, false);
- iqk_initialized = true;
+ rtlphy->iqk_initialized = true;
}
rtl92c_dm_check_txpower_tracking(hw);
@@ -1004,6 +1022,13 @@ static enum version_8192c _rtl92ce_read_
? CHIP_VENDOR_UMC_B_CUT : CHIP_UNKNOWN) |
CHIP_VENDOR_UMC));
}
+ if (IS_92C_SERIAL(version)) {
+ value32 = rtl_read_dword(rtlpriv, REG_HPON_FSM);
+ version = (enum version_8192c)(version |
+ ((CHIP_BONDING_IDENTIFIER(value32)
+ == CHIP_BONDING_92C_1T2R) ?
+ RF_TYPE_1T2R : 0));
+ }
}
switch (version) {
@@ -1019,12 +1044,30 @@ static enum version_8192c _rtl92ce_read_
case VERSION_A_CHIP_88C:
versionid = "A_CHIP_88C";
break;
+ case VERSION_NORMAL_UMC_CHIP_92C_1T2R_A_CUT:
+ versionid = "A_CUT_92C_1T2R";
+ break;
+ case VERSION_NORMAL_UMC_CHIP_92C_A_CUT:
+ versionid = "A_CUT_92C";
+ break;
+ case VERSION_NORMAL_UMC_CHIP_88C_A_CUT:
+ versionid = "A_CUT_88C";
+ break;
+ case VERSION_NORMAL_UMC_CHIP_92C_1T2R_B_CUT:
+ versionid = "B_CUT_92C_1T2R";
+ break;
+ case VERSION_NORMAL_UMC_CHIP_92C_B_CUT:
+ versionid = "B_CUT_92C";
+ break;
+ case VERSION_NORMAL_UMC_CHIP_88C_B_CUT:
+ versionid = "B_CUT_88C";
+ break;
default:
versionid = "Unknown. Bug?";
break;
}
- RT_TRACE(rtlpriv, COMP_INIT, DBG_TRACE,
+ RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG,
"Chip Version ID: %s\n", versionid);
switch (version & 0x3) {
@@ -1197,6 +1240,7 @@ static void _rtl92ce_poweroff_adapter(st
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci_priv *rtlpcipriv = rtl_pcipriv(hw);
+ struct rtl_hal *rtlhal = rtl_hal(rtlpriv);
u8 u1b_tmp;
u32 u4b_tmp;
@@ -1225,7 +1269,8 @@ static void _rtl92ce_poweroff_adapter(st
rtl_write_word(rtlpriv, REG_GPIO_IO_SEL, 0x0790);
rtl_write_word(rtlpriv, REG_LEDCFG0, 0x8080);
rtl_write_byte(rtlpriv, REG_AFE_PLL_CTRL, 0x80);
- rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
+ if (!IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version))
+ rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
if (rtlpcipriv->bt_coexist.bt_coexistence) {
u4b_tmp = rtl_read_dword(rtlpriv, REG_AFE_XTAL_CTRL);
u4b_tmp |= 0x03824800;
@@ -1254,6 +1299,9 @@ void rtl92ce_card_disable(struct ieee802
rtlpriv->cfg->ops->led_control(hw, LED_CTL_POWER_OFF);
RT_SET_PS_LEVEL(ppsc, RT_RF_OFF_LEVL_HALT_NIC);
_rtl92ce_poweroff_adapter(hw);
+
+ /* after power off we should do iqk again */
+ rtlpriv->phy.iqk_initialized = false;
}
void rtl92ce_interrupt_recognized(struct ieee80211_hw *hw,
@@ -1355,9 +1403,9 @@ static void _rtl92ce_read_txpower_info_f
tempval = hwinfo[EEPROM_TXPOWERHT40_2SDIFF + i];
else
tempval = EEPROM_DEFAULT_HT40_2SDIFF;
- rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_A][i] =
+ rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_A][i] =
(tempval & 0xf);
- rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_B][i] =
+ rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_B][i] =
((tempval & 0xf0) >> 4);
}
@@ -1381,7 +1429,7 @@ static void _rtl92ce_read_txpower_info_f
"RF(%d) EEPROM HT40 2S Diff Area(%d) = 0x%x\n",
rf_path, i,
rtlefuse->
- eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][i]);
+ eprom_chnl_txpwr_ht40_2sdf[rf_path][i]);
for (rf_path = 0; rf_path < 2; rf_path++) {
for (i = 0; i < 14; i++) {
@@ -1396,14 +1444,14 @@ static void _rtl92ce_read_txpower_info_f
if ((rtlefuse->
eeprom_chnlarea_txpwr_ht40_1s[rf_path][index] -
rtlefuse->
- eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][index])
+ eprom_chnl_txpwr_ht40_2sdf[rf_path][index])
> 0) {
rtlefuse->txpwrlevel_ht40_2s[rf_path][i] =
rtlefuse->
eeprom_chnlarea_txpwr_ht40_1s[rf_path]
[index] -
rtlefuse->
- eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path]
+ eprom_chnl_txpwr_ht40_2sdf[rf_path]
[index];
} else {
rtlefuse->txpwrlevel_ht40_2s[rf_path][i] = 0;
@@ -1912,6 +1960,8 @@ static void rtl92ce_update_hal_rate_mask
ratr_bitmap &= 0x0f0ff0ff;
break;
}
+ sta_entry->ratr_index = ratr_index;
+
RT_TRACE(rtlpriv, COMP_RATR, DBG_DMESG,
"ratr_bitmap :%x\n", ratr_bitmap);
*(u32 *)&rate_mask = (ratr_bitmap & 0x0fffffff) |
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/phy.c
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/phy.c
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/phy.c
@@ -82,6 +82,8 @@ bool rtl92c_phy_mac_config(struct ieee80
if (is92c)
rtl_write_byte(rtlpriv, 0x14, 0x71);
+ else
+ rtl_write_byte(rtlpriv, 0x04CA, 0x0A);
return rtstatus;
}
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/sw.c
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/sw.c
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/sw.c
@@ -162,12 +162,10 @@ int rtl92c_init_sw_vars(struct ieee80211
/* request fw */
if (IS_VENDOR_UMC_A_CUT(rtlhal->version) &&
- !IS_92C_SERIAL(rtlhal->version)) {
+ !IS_92C_SERIAL(rtlhal->version))
rtlpriv->cfg->fw_name = "rtlwifi/rtl8192cfwU.bin";
- } else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version)) {
+ else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version))
rtlpriv->cfg->fw_name = "rtlwifi/rtl8192cfwU_B.bin";
- pr_info("****** This B_CUT device may not work with kernels 3.6 and earlier\n");
- }
rtlpriv->max_fw_size = 0x4000;
pr_info("Using firmware %s\n", rtlpriv->cfg->fw_name);
Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/trx.c
===================================================================
--- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/trx.c
+++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/trx.c
@@ -127,11 +127,11 @@ static void _rtl92ce_query_rxphystatus(s
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct phy_sts_cck_8192s_t *cck_buf;
+ struct rtl_ps_ctl *ppsc = rtl_psc(rtlpriv);
s8 rx_pwr_all = 0, rx_pwr[4];
u8 evm, pwdb_all, rf_rx_num = 0;
u8 i, max_spatial_stream;
u32 rssi, total_rssi = 0;
- bool in_powersavemode = false;
bool is_cck_rate;
is_cck_rate = RX_HAL_IS_CCK_RATE(pdesc);
@@ -147,7 +147,7 @@ static void _rtl92ce_query_rxphystatus(s
u8 report, cck_highpwr;
cck_buf = (struct phy_sts_cck_8192s_t *)p_drvinfo;
- if (!in_powersavemode)
+ if (ppsc->rfpwr_state == ERFON)
cck_highpwr = (u8) rtl_get_bbreg(hw,
RFPGA0_XA_HSSIPARAMETER2,
BIT(9));
On Mon, 17 Sep 2012 15:35:43 -0500, Larry Finger <[email protected]> wrote :
> Realtek devices with designation RTL8188CE-VL have the so-called B-cut
> of the wireless chip. This patch adds the special programming needed by
> these devices.
>
> Signed-off-by: Larry Finger <[email protected]>
> Cc: Anisse Astier <[email protected]>
> Cc: Li Chaoming <[email protected]>
> ---
> drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c | 21 +++++++
> drivers/net/wireless/rtlwifi/rtl8192ce/def.h | 3 +
> drivers/net/wireless/rtlwifi/rtl8192ce/hw.c | 61 ++++++++++++++++++--
> drivers/net/wireless/rtlwifi/rtl8192ce/phy.c | 4 +-
> drivers/net/wireless/rtlwifi/rtl8192ce/sw.c | 6 +-
> drivers/net/wireless/rtlwifi/rtl8192ce/trx.c | 4 +-
> 6 files changed, 87 insertions(+), 12 deletions(-)
> ---
> V1 => V2 Remove extraneous white space.
>
>
> John,
>
> This patch is too invasive to backport to the stable kernels, thus it should
> be applied to 3.7.
>
> Thanks,
>
> Larry
> ---
>
[snip]
> Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
> ===================================================================
> --- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
> +++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
> @@ -896,7 +896,6 @@ int rtl92ce_hw_init(struct ieee80211_hw
> struct rtl_phy *rtlphy = &(rtlpriv->phy);
> struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
> struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
> - static bool iqk_initialized; /* initialized to false */
> bool rtstatus = true;
> bool is92c;
> int err;
> @@ -921,9 +920,28 @@ int rtl92ce_hw_init(struct ieee80211_hw
>
> rtlhal->last_hmeboxnum = 0;
> rtl92c_phy_mac_config(hw);
> + /* because last function modify RCR, so we update
> + * rcr var here, or TP will unstable for receive_config
> + * is wrong, RX RCR_ACRC32 will cause TP unstabel & Rx
> + * RCR_APP_ICV will cause mac80211 unassoc for cisco 1252*/
> + rtlpci->receive_config = rtl_read_dword(rtlpriv, REG_RCR);
> + rtlpci->receive_config &= ~(RCR_ACRC32 | RCR_AICV);
> + rtl_write_dword(rtlpriv, REG_RCR, rtlpci->receive_config);
> rtl92c_phy_bb_config(hw);
> rtlphy->rf_mode = RF_OP_BY_SW_3WIRE;
> rtl92c_phy_rf_config(hw);
> + if (IS_VENDOR_UMC_A_CUT(rtlhal->version) &&
> + !IS_92C_SERIAL(rtlhal->version)) {
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G1, MASKDWORD, 0x30255);
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G2, MASKDWORD, 0x50a00);
> + } else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version)) {
> + rtl_set_rfreg(hw, RF90_PATH_A, 0x0C, MASKDWORD, 0x894AE);
> + rtl_set_rfreg(hw, RF90_PATH_A, 0x0A, MASKDWORD, 0x1AF31);
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_IPA, MASKDWORD, 0x8F425);
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_SYN_G2, MASKDWORD, 0x4F200);
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK1, MASKDWORD, 0x44053);
> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK2, MASKDWORD, 0x80201);
> + }
> rtlphy->rfreg_chnlval[0] = rtl_get_rfreg(hw, (enum radio_path)0,
> RF_CHNLBW, RFREG_OFFSET_MASK);
> rtlphy->rfreg_chnlval[1] = rtl_get_rfreg(hw, (enum radio_path)1,
> @@ -945,11 +963,11 @@ int rtl92ce_hw_init(struct ieee80211_hw
>
> if (ppsc->rfpwr_state == ERFON) {
> rtl92c_phy_set_rfpath_switch(hw, 1);
> - if (iqk_initialized) {
> + if (rtlphy->iqk_initialized) {
> rtl92c_phy_iq_calibrate(hw, true);
> } else {
> rtl92c_phy_iq_calibrate(hw, false);
> - iqk_initialized = true;
> + rtlphy->iqk_initialized = true;
> }
>
> rtl92c_dm_check_txpower_tracking(hw);
> @@ -1004,6 +1022,13 @@ static enum version_8192c _rtl92ce_read_
> ? CHIP_VENDOR_UMC_B_CUT : CHIP_UNKNOWN) |
> CHIP_VENDOR_UMC));
> }
> + if (IS_92C_SERIAL(version)) {
> + value32 = rtl_read_dword(rtlpriv, REG_HPON_FSM);
> + version = (enum version_8192c)(version |
> + ((CHIP_BONDING_IDENTIFIER(value32)
> + == CHIP_BONDING_92C_1T2R) ?
> + RF_TYPE_1T2R : 0));
> + }
> }
>
> switch (version) {
> @@ -1019,12 +1044,30 @@ static enum version_8192c _rtl92ce_read_
> case VERSION_A_CHIP_88C:
> versionid = "A_CHIP_88C";
> break;
> + case VERSION_NORMAL_UMC_CHIP_92C_1T2R_A_CUT:
> + versionid = "A_CUT_92C_1T2R";
> + break;
> + case VERSION_NORMAL_UMC_CHIP_92C_A_CUT:
> + versionid = "A_CUT_92C";
> + break;
> + case VERSION_NORMAL_UMC_CHIP_88C_A_CUT:
> + versionid = "A_CUT_88C";
> + break;
> + case VERSION_NORMAL_UMC_CHIP_92C_1T2R_B_CUT:
> + versionid = "B_CUT_92C_1T2R";
> + break;
> + case VERSION_NORMAL_UMC_CHIP_92C_B_CUT:
> + versionid = "B_CUT_92C";
> + break;
> + case VERSION_NORMAL_UMC_CHIP_88C_B_CUT:
> + versionid = "B_CUT_88C";
> + break;
> default:
> versionid = "Unknown. Bug?";
> break;
> }
>
> - RT_TRACE(rtlpriv, COMP_INIT, DBG_TRACE,
> + RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG,
> "Chip Version ID: %s\n", versionid);
>
> switch (version & 0x3) {
> @@ -1197,6 +1240,7 @@ static void _rtl92ce_poweroff_adapter(st
> {
> struct rtl_priv *rtlpriv = rtl_priv(hw);
> struct rtl_pci_priv *rtlpcipriv = rtl_pcipriv(hw);
> + struct rtl_hal *rtlhal = rtl_hal(rtlpriv);
> u8 u1b_tmp;
> u32 u4b_tmp;
>
> @@ -1225,7 +1269,8 @@ static void _rtl92ce_poweroff_adapter(st
> rtl_write_word(rtlpriv, REG_GPIO_IO_SEL, 0x0790);
> rtl_write_word(rtlpriv, REG_LEDCFG0, 0x8080);
> rtl_write_byte(rtlpriv, REG_AFE_PLL_CTRL, 0x80);
> - rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
> + if (!IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version))
> + rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
> if (rtlpcipriv->bt_coexist.bt_coexistence) {
> u4b_tmp = rtl_read_dword(rtlpriv, REG_AFE_XTAL_CTRL);
> u4b_tmp |= 0x03824800;
> @@ -1254,6 +1299,9 @@ void rtl92ce_card_disable(struct ieee802
> rtlpriv->cfg->ops->led_control(hw, LED_CTL_POWER_OFF);
> RT_SET_PS_LEVEL(ppsc, RT_RF_OFF_LEVL_HALT_NIC);
> _rtl92ce_poweroff_adapter(hw);
> +
> + /* after power off we should do iqk again */
> + rtlpriv->phy.iqk_initialized = false;
> }
>
> void rtl92ce_interrupt_recognized(struct ieee80211_hw *hw,
This part:
> @@ -1355,9 +1403,9 @@ static void _rtl92ce_read_txpower_info_f
> tempval = hwinfo[EEPROM_TXPOWERHT40_2SDIFF + i];
> else
> tempval = EEPROM_DEFAULT_HT40_2SDIFF;
> - rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_A][i] =
> + rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_A][i] =
> (tempval & 0xf);
> - rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_B][i] =
> + rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_B][i] =
> ((tempval & 0xf0) >> 4);
> }
>
> @@ -1381,7 +1429,7 @@ static void _rtl92ce_read_txpower_info_f
> "RF(%d) EEPROM HT40 2S Diff Area(%d) = 0x%x\n",
> rf_path, i,
> rtlefuse->
> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][i]);
> + eprom_chnl_txpwr_ht40_2sdf[rf_path][i]);
>
> for (rf_path = 0; rf_path < 2; rf_path++) {
> for (i = 0; i < 14; i++) {
> @@ -1396,14 +1444,14 @@ static void _rtl92ce_read_txpower_info_f
> if ((rtlefuse->
> eeprom_chnlarea_txpwr_ht40_1s[rf_path][index] -
> rtlefuse->
> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][index])
> + eprom_chnl_txpwr_ht40_2sdf[rf_path][index])
> > 0) {
> rtlefuse->txpwrlevel_ht40_2s[rf_path][i] =
> rtlefuse->
> eeprom_chnlarea_txpwr_ht40_1s[rf_path]
> [index] -
> rtlefuse->
> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path]
> + eprom_chnl_txpwr_ht40_2sdf[rf_path]
> [index];
> } else {
> rtlefuse->txpwrlevel_ht40_2s[rf_path][i] = 0;
wasn't in V1 of the patch. Is the rename normal?
Anisse
On 09/18/2012 09:09 AM, Anisse Astier wrote:
> On Mon, 17 Sep 2012 15:35:43 -0500, Larry Finger <[email protected]> wrote :
>
>> Realtek devices with designation RTL8188CE-VL have the so-called B-cut
>> of the wireless chip. This patch adds the special programming needed by
>> these devices.
>>
>> Signed-off-by: Larry Finger <[email protected]>
>> Cc: Anisse Astier <[email protected]>
>> Cc: Li Chaoming <[email protected]>
>> ---
>> drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c | 21 +++++++
>> drivers/net/wireless/rtlwifi/rtl8192ce/def.h | 3 +
>> drivers/net/wireless/rtlwifi/rtl8192ce/hw.c | 61 ++++++++++++++++++--
>> drivers/net/wireless/rtlwifi/rtl8192ce/phy.c | 4 +-
>> drivers/net/wireless/rtlwifi/rtl8192ce/sw.c | 6 +-
>> drivers/net/wireless/rtlwifi/rtl8192ce/trx.c | 4 +-
>> 6 files changed, 87 insertions(+), 12 deletions(-)
>> ---
>> V1 => V2 Remove extraneous white space.
>>
>>
>> John,
>>
>> This patch is too invasive to backport to the stable kernels, thus it should
>> be applied to 3.7.
>>
>> Thanks,
>>
>> Larry
>> ---
>>
>
> [snip]
>
>> Index: wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
>> ===================================================================
>> --- wireless-testing-new.orig/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
>> +++ wireless-testing-new/drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
>> @@ -896,7 +896,6 @@ int rtl92ce_hw_init(struct ieee80211_hw
>> struct rtl_phy *rtlphy = &(rtlpriv->phy);
>> struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
>> struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
>> - static bool iqk_initialized; /* initialized to false */
>> bool rtstatus = true;
>> bool is92c;
>> int err;
>> @@ -921,9 +920,28 @@ int rtl92ce_hw_init(struct ieee80211_hw
>>
>> rtlhal->last_hmeboxnum = 0;
>> rtl92c_phy_mac_config(hw);
>> + /* because last function modify RCR, so we update
>> + * rcr var here, or TP will unstable for receive_config
>> + * is wrong, RX RCR_ACRC32 will cause TP unstabel & Rx
>> + * RCR_APP_ICV will cause mac80211 unassoc for cisco 1252*/
>> + rtlpci->receive_config = rtl_read_dword(rtlpriv, REG_RCR);
>> + rtlpci->receive_config &= ~(RCR_ACRC32 | RCR_AICV);
>> + rtl_write_dword(rtlpriv, REG_RCR, rtlpci->receive_config);
>> rtl92c_phy_bb_config(hw);
>> rtlphy->rf_mode = RF_OP_BY_SW_3WIRE;
>> rtl92c_phy_rf_config(hw);
>> + if (IS_VENDOR_UMC_A_CUT(rtlhal->version) &&
>> + !IS_92C_SERIAL(rtlhal->version)) {
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G1, MASKDWORD, 0x30255);
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RX_G2, MASKDWORD, 0x50a00);
>> + } else if (IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version)) {
>> + rtl_set_rfreg(hw, RF90_PATH_A, 0x0C, MASKDWORD, 0x894AE);
>> + rtl_set_rfreg(hw, RF90_PATH_A, 0x0A, MASKDWORD, 0x1AF31);
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_IPA, MASKDWORD, 0x8F425);
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_SYN_G2, MASKDWORD, 0x4F200);
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK1, MASKDWORD, 0x44053);
>> + rtl_set_rfreg(hw, RF90_PATH_A, RF_RCK2, MASKDWORD, 0x80201);
>> + }
>> rtlphy->rfreg_chnlval[0] = rtl_get_rfreg(hw, (enum radio_path)0,
>> RF_CHNLBW, RFREG_OFFSET_MASK);
>> rtlphy->rfreg_chnlval[1] = rtl_get_rfreg(hw, (enum radio_path)1,
>> @@ -945,11 +963,11 @@ int rtl92ce_hw_init(struct ieee80211_hw
>>
>> if (ppsc->rfpwr_state == ERFON) {
>> rtl92c_phy_set_rfpath_switch(hw, 1);
>> - if (iqk_initialized) {
>> + if (rtlphy->iqk_initialized) {
>> rtl92c_phy_iq_calibrate(hw, true);
>> } else {
>> rtl92c_phy_iq_calibrate(hw, false);
>> - iqk_initialized = true;
>> + rtlphy->iqk_initialized = true;
>> }
>>
>> rtl92c_dm_check_txpower_tracking(hw);
>> @@ -1004,6 +1022,13 @@ static enum version_8192c _rtl92ce_read_
>> ? CHIP_VENDOR_UMC_B_CUT : CHIP_UNKNOWN) |
>> CHIP_VENDOR_UMC));
>> }
>> + if (IS_92C_SERIAL(version)) {
>> + value32 = rtl_read_dword(rtlpriv, REG_HPON_FSM);
>> + version = (enum version_8192c)(version |
>> + ((CHIP_BONDING_IDENTIFIER(value32)
>> + == CHIP_BONDING_92C_1T2R) ?
>> + RF_TYPE_1T2R : 0));
>> + }
>> }
>>
>> switch (version) {
>> @@ -1019,12 +1044,30 @@ static enum version_8192c _rtl92ce_read_
>> case VERSION_A_CHIP_88C:
>> versionid = "A_CHIP_88C";
>> break;
>> + case VERSION_NORMAL_UMC_CHIP_92C_1T2R_A_CUT:
>> + versionid = "A_CUT_92C_1T2R";
>> + break;
>> + case VERSION_NORMAL_UMC_CHIP_92C_A_CUT:
>> + versionid = "A_CUT_92C";
>> + break;
>> + case VERSION_NORMAL_UMC_CHIP_88C_A_CUT:
>> + versionid = "A_CUT_88C";
>> + break;
>> + case VERSION_NORMAL_UMC_CHIP_92C_1T2R_B_CUT:
>> + versionid = "B_CUT_92C_1T2R";
>> + break;
>> + case VERSION_NORMAL_UMC_CHIP_92C_B_CUT:
>> + versionid = "B_CUT_92C";
>> + break;
>> + case VERSION_NORMAL_UMC_CHIP_88C_B_CUT:
>> + versionid = "B_CUT_88C";
>> + break;
>> default:
>> versionid = "Unknown. Bug?";
>> break;
>> }
>>
>> - RT_TRACE(rtlpriv, COMP_INIT, DBG_TRACE,
>> + RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG,
>> "Chip Version ID: %s\n", versionid);
>>
>> switch (version & 0x3) {
>> @@ -1197,6 +1240,7 @@ static void _rtl92ce_poweroff_adapter(st
>> {
>> struct rtl_priv *rtlpriv = rtl_priv(hw);
>> struct rtl_pci_priv *rtlpcipriv = rtl_pcipriv(hw);
>> + struct rtl_hal *rtlhal = rtl_hal(rtlpriv);
>> u8 u1b_tmp;
>> u32 u4b_tmp;
>>
>> @@ -1225,7 +1269,8 @@ static void _rtl92ce_poweroff_adapter(st
>> rtl_write_word(rtlpriv, REG_GPIO_IO_SEL, 0x0790);
>> rtl_write_word(rtlpriv, REG_LEDCFG0, 0x8080);
>> rtl_write_byte(rtlpriv, REG_AFE_PLL_CTRL, 0x80);
>> - rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
>> + if (!IS_81xxC_VENDOR_UMC_B_CUT(rtlhal->version))
>> + rtl_write_byte(rtlpriv, REG_SPS0_CTRL, 0x23);
>> if (rtlpcipriv->bt_coexist.bt_coexistence) {
>> u4b_tmp = rtl_read_dword(rtlpriv, REG_AFE_XTAL_CTRL);
>> u4b_tmp |= 0x03824800;
>> @@ -1254,6 +1299,9 @@ void rtl92ce_card_disable(struct ieee802
>> rtlpriv->cfg->ops->led_control(hw, LED_CTL_POWER_OFF);
>> RT_SET_PS_LEVEL(ppsc, RT_RF_OFF_LEVL_HALT_NIC);
>> _rtl92ce_poweroff_adapter(hw);
>> +
>> + /* after power off we should do iqk again */
>> + rtlpriv->phy.iqk_initialized = false;
>> }
>>
>> void rtl92ce_interrupt_recognized(struct ieee80211_hw *hw,
>
> This part:
>> @@ -1355,9 +1403,9 @@ static void _rtl92ce_read_txpower_info_f
>> tempval = hwinfo[EEPROM_TXPOWERHT40_2SDIFF + i];
>> else
>> tempval = EEPROM_DEFAULT_HT40_2SDIFF;
>> - rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_A][i] =
>> + rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_A][i] =
>> (tempval & 0xf);
>> - rtlefuse->eeprom_chnlarea_txpwr_ht40_2sdiif[RF90_PATH_B][i] =
>> + rtlefuse->eprom_chnl_txpwr_ht40_2sdf[RF90_PATH_B][i] =
>> ((tempval & 0xf0) >> 4);
>> }
>>
>> @@ -1381,7 +1429,7 @@ static void _rtl92ce_read_txpower_info_f
>> "RF(%d) EEPROM HT40 2S Diff Area(%d) = 0x%x\n",
>> rf_path, i,
>> rtlefuse->
>> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][i]);
>> + eprom_chnl_txpwr_ht40_2sdf[rf_path][i]);
>>
>> for (rf_path = 0; rf_path < 2; rf_path++) {
>> for (i = 0; i < 14; i++) {
>> @@ -1396,14 +1444,14 @@ static void _rtl92ce_read_txpower_info_f
>> if ((rtlefuse->
>> eeprom_chnlarea_txpwr_ht40_1s[rf_path][index] -
>> rtlefuse->
>> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path][index])
>> + eprom_chnl_txpwr_ht40_2sdf[rf_path][index])
>> > 0) {
>> rtlefuse->txpwrlevel_ht40_2s[rf_path][i] =
>> rtlefuse->
>> eeprom_chnlarea_txpwr_ht40_1s[rf_path]
>> [index] -
>> rtlefuse->
>> - eeprom_chnlarea_txpwr_ht40_2sdiif[rf_path]
>> + eprom_chnl_txpwr_ht40_2sdf[rf_path]
>> [index];
>> } else {
>> rtlefuse->txpwrlevel_ht40_2s[rf_path][i] = 0;
>
> wasn't in V1 of the patch. Is the rename normal?
The original length of the variable name was causing extreme difficulty in
keeping all lines to 80 characters in the code for the new driver for the
RTL8723AE device. The renaming helped. You are correct that the change should be
documented.
Larry