From: Ajay Singh <[email protected]>
Use YAML schemas for wilc1000 DT binding documentations. Currently, the
files are present in '/drivers/staging/wilc1000/' but these will be
moved to '/Documentation/devicetree/bindings/net/wireless/' later once
the driver move out-of-staging.
Signed-off-by: Ajay Singh <[email protected]>
---
.../wilc1000/microchip,wilc1000,sdio.txt | 38 -----------
.../wilc1000/microchip,wilc1000,sdio.yaml | 68 +++++++++++++++++++
.../wilc1000/microchip,wilc1000,spi.txt | 34 ----------
.../wilc1000/microchip,wilc1000,spi.yaml | 61 +++++++++++++++++
4 files changed, 129 insertions(+), 72 deletions(-)
delete mode 100644 drivers/staging/wilc1000/microchip,wilc1000,sdio.txt
create mode 100644 drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
delete mode 100644 drivers/staging/wilc1000/microchip,wilc1000,spi.txt
create mode 100644 drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,sdio.txt b/drivers/staging/wilc1000/microchip,wilc1000,sdio.txt
deleted file mode 100644
index da5235950a70..000000000000
--- a/drivers/staging/wilc1000/microchip,wilc1000,sdio.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-* Microchip WILC wireless SDIO device
-
-The wilc1000 chips can be connected via SDIO. The node is used to specifiy
-child node to the SDIO controller that connects the device to the system.
-
-Required properties:
-- compatible : Should be "microchip,wilc1000-spi"
-- irq-gpios : Connect to a host IRQ
-- reg : Slot ID used in the controller
-
-Optional:
-- bus-width : Number of data lines wired up the slot. Default 1 bit.
-- rtc_clk : Clock connected on the rtc clock line. Must be assigned
- a frequency with assigned-clocks property, and must be
- connected to a clock provider.
-
-Examples:
-mmc1: mmc@fc000000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
- non-removable;
- vmmc-supply = <&vcc_mmc1_reg>;
- vqmmc-supply = <&vcc_3v3_reg>;
- status = "okay";
-
- wilc_sdio@0 {
- compatible = "microchip,wilc1000-sdio";
- irq-gpios = <&pioC 27 0>;
- clocks = <&pck1>;
- clock-names = "rtc_clk";
- assigned-clocks = <&pck1>;
- assigned-clock-rates = <32768>;
- status = "okay";
- reg = <0>;
- bus-width = <4>;
- }
- };
-}
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
new file mode 100644
index 000000000000..b338f569f7e2
--- /dev/null
+++ b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000,sdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip WILC wireless SDIO devicetree bindings
+
+maintainers:
+ - Adham Abozaeid <[email protected]>
+ - Ajay Singh <[email protected]>
+
+description:
+ The wilc1000 chips can be connected via SDIO. The node is used to
+ specify child node to the SDIO controller that connects the device
+ to the system.
+
+properties:
+ compatible:
+ const: microchip,wilc1000-sdio
+
+ irq-gpios:
+ description: The GPIO phandle connect to a host IRQ.
+ maxItems: 1
+
+ reg:
+ description: Slot ID used in the controller.
+ maxItems: 1
+
+ clocks:
+ description: phandle to the clock connected on rtc clock line.
+ maxItems: 1
+
+ bus-width:
+ description: The number of data lines wired up the slot.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 4, 8]
+ - default: 1
+
+required:
+ - compatible
+ - irq-gpios
+ - reg
+
+examples:
+ - |
+ mmc1: mmc@fc000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+ non-removable;
+ vmmc-supply = <&vcc_mmc1_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ status = "okay";
+ wilc_sdio@0 {
+ compatible = "microchip,wilc1000-sdio";
+ irq-gpios = <&pioC 27 0>;
+ reg = <0>;
+ clocks = <&pck1>;
+ clock-names = "rtc_clk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <32768>;
+ status = "okay";
+ bus-width = <4>;
+ };
+ };
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,spi.txt b/drivers/staging/wilc1000/microchip,wilc1000,spi.txt
deleted file mode 100644
index 34236932dbb6..000000000000
--- a/drivers/staging/wilc1000/microchip,wilc1000,spi.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-* Microchip WILC wireless SPI device
-
-The wilc1000 chips can be connected via SPI. This document describes
-the binding for the SPI connected module.
-
-Required properties:
-- compatible : Should be "microchip,wilc1000-spi"
-- spi-max-frequency : Maximum SPI clocking speed of device in Hz
-- reg : Chip select address of device
-- irq-gpios : Connect to a host IRQ
-
-Optional:
-- rtc_clk : Clock connected on the rtc clock line. Must be assigned
- a frequency with assigned-clocks property, and must be
- connected to a clock provider.
-
-Examples:
-
-spi1: spi@fc018000 {
- cs-gpios = <&pioB 21 0>;
- status = "okay";
-
- wilc_spi@0 {
- compatible = "microchip,wilc1000-spi";
- spi-max-frequency = <48000000>;
- reg = <0>;
- irq-gpios = <&pioC 27 0>;
- clocks = <&pck1>;
- clock-names = "rtc_clk";
- assigned-clocks = <&pck1>;
- assigned-clock-rates = <32768>;
- status = "okay";
- };
-};
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml b/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
new file mode 100644
index 000000000000..cc8ed64ce627
--- /dev/null
+++ b/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000,spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip WILC wireless SPI devicetree bindings
+
+maintainers:
+ - Adham Abozaeid <[email protected]>
+ - Ajay Singh <[email protected]>
+
+description:
+ The wilc1000 chips can be connected via SPI. This document describes
+ the binding for the SPI connected module.
+
+properties:
+ compatible:
+ const: microchip,wilc1000-spi
+
+ spi-max-frequency:
+ description: Maximum SPI clocking speed of device in Hz.
+ maxItems: 1
+
+ reg:
+ description: Chip select address of device.
+ maxItems: 1
+
+ irq-gpios:
+ description: The GPIO phandle connect to a host IRQ.
+ maxItems: 1
+
+ clocks:
+ description: phandle to the clock connected on rtc clock line.
+ maxItems: 1
+
+required:
+ - compatible
+ - spi-max-frequency
+ - reg
+ - irq-gpios
+
+examples:
+ - |
+ spi1: spi@fc018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs-gpios = <&pioB 21 0>;
+ status = "okay";
+ wilc_spi@0 {
+ compatible = "microchip,wilc1000-spi";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ irq-gpios = <&pioC 27 0>;
+ clocks = <&pck1>;
+ clock-names = "rtc_clk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <32768>;
+ status = "okay";
+ };
+ };
--
2.24.0