From: Ajay Singh <[email protected]>
This patch series contains changes to handle DT binding documentation
related review comments. The changes were suggested during the full
driver review [1] & [2].
First submitting these patches to staging and later will include them
as part of the full driver review patch series.
[1]. https://patchwork.kernel.org/patch/11415897
[2]. https://patchwork.kernel.org/patch/11415901
Ajay Singh (2):
staging: wilc1000: use 'interrupts' property instead of 'irq-gpio'
staging: wilc1000: use single DT binding documentation for SDIO and
SPI
.../net/wireless/microchip,wilc1000.yaml | 79 +++++++++++++++++++
.../wilc1000/microchip,wilc1000,sdio.yaml | 68 ----------------
.../wilc1000/microchip,wilc1000,spi.yaml | 61 --------------
.../staging/wilc1000/microchip,wilc1000.yaml | 79 +++++++++++++++++++
drivers/staging/wilc1000/netdev.c | 24 ++----
drivers/staging/wilc1000/netdev.h | 1 -
drivers/staging/wilc1000/sdio.c | 35 ++++----
drivers/staging/wilc1000/spi.c | 17 +---
drivers/staging/wilc1000/wlan.h | 1 -
9 files changed, 182 insertions(+), 183 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
delete mode 100644 drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
delete mode 100644 drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
create mode 100644 drivers/staging/wilc1000/microchip,wilc1000.yaml
--
2.24.0
From: Ajay Singh <[email protected]>
Make use of 'interrupts' property instead of using gpio for handling
the interrupt as suggested in [1].
[1]. https://lore.kernel.org/linux-wireless/20200303015558.GA6876@bogus/
Signed-off-by: Ajay Singh <[email protected]>
---
.../net/wireless/microchip,wilc1000.yaml | 79 +++++++++++++++++++
.../wilc1000/microchip,wilc1000,sdio.yaml | 8 +-
.../wilc1000/microchip,wilc1000,spi.yaml | 8 +-
drivers/staging/wilc1000/netdev.c | 24 ++----
drivers/staging/wilc1000/netdev.h | 1 -
drivers/staging/wilc1000/sdio.c | 31 +++-----
drivers/staging/wilc1000/spi.c | 15 +---
drivers/staging/wilc1000/wlan.h | 1 -
8 files changed, 108 insertions(+), 59 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
new file mode 100644
index 000000000000..a1914449ad07
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
@@ -0,0 +1,79 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip WILC wireless devicetree bindings
+
+maintainers:
+ - Adham Abozaeid <[email protected]>
+ - Ajay Singh <[email protected]>
+
+description:
+ The wilc1000 chips can be connected via SPI or SDIO. This document
+ describes the binding to connect wilc devices.
+
+properties:
+ compatible:
+ const: microchip,wilc1000
+
+ spi-max-frequency:
+ description: Maximum SPI clocking speed of device in Hz.
+ maxItems: 1
+
+ reg:
+ description: Chip select address of device.
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ description: phandle to the clock connected on rtc clock line.
+ maxItems: 1
+
+ clock-names:
+ const: rtc
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+examples:
+ - |
+ spi1: spi@fc018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs-gpios = <&pioB 21 0>;
+ wifi@0 {
+ compatible = "microchip,wilc1000";
+ spi-max-frequency = <48000000>;
+ reg = <0>;
+ interrupt-parent = <&pioC>;
+ interrupts = <27 0>;
+ clocks = <&pck1>;
+ clock-names = "rtc";
+ };
+ };
+
+ - |
+ mmc1: mmc@fc000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+ non-removable;
+ vmmc-supply = <&vcc_mmc1_reg>;
+ vqmmc-supply = <&vcc_3v3_reg>;
+ bus-width = <4>;
+ wifi@0 {
+ compatible = "microchip,wilc1000";
+ reg = <0>;
+ interrupt-parent = <&pioC>;
+ interrupts = <27 0>;
+ clocks = <&pck1>;
+ clock-names = "rtc";
+ };
+ };
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
index b338f569f7e2..9df7327bc668 100644
--- a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
+++ b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
@@ -19,8 +19,7 @@ properties:
compatible:
const: microchip,wilc1000-sdio
- irq-gpios:
- description: The GPIO phandle connect to a host IRQ.
+ interrupts:
maxItems: 1
reg:
@@ -40,7 +39,7 @@ properties:
required:
- compatible
- - irq-gpios
+ - interrupts
- reg
examples:
@@ -56,7 +55,8 @@ examples:
status = "okay";
wilc_sdio@0 {
compatible = "microchip,wilc1000-sdio";
- irq-gpios = <&pioC 27 0>;
+ interrupt-parent = <&pioC>;
+ interrupts = <27 0>;
reg = <0>;
clocks = <&pck1>;
clock-names = "rtc_clk";
diff --git a/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml b/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
index cc8ed64ce627..dd5e8da1f562 100644
--- a/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
+++ b/drivers/staging/wilc1000/microchip,wilc1000,spi.yaml
@@ -26,8 +26,7 @@ properties:
description: Chip select address of device.
maxItems: 1
- irq-gpios:
- description: The GPIO phandle connect to a host IRQ.
+ interrupts:
maxItems: 1
clocks:
@@ -38,7 +37,7 @@ required:
- compatible
- spi-max-frequency
- reg
- - irq-gpios
+ - interrupts
examples:
- |
@@ -51,7 +50,8 @@ examples:
compatible = "microchip,wilc1000-spi";
spi-max-frequency = <48000000>;
reg = <0>;
- irq-gpios = <&pioC 27 0>;
+ interrupt-parent = <&pioC>;
+ interrupts = <27 0>;
clocks = <&pck1>;
clock-names = "rtc_clk";
assigned-clocks = <&pck1>;
diff --git a/drivers/staging/wilc1000/netdev.c b/drivers/staging/wilc1000/netdev.c
index 045f5cdfdca0..a61c1a7aefa8 100644
--- a/drivers/staging/wilc1000/netdev.c
+++ b/drivers/staging/wilc1000/netdev.c
@@ -46,29 +46,21 @@ static irqreturn_t isr_bh_routine(int irq, void *userdata)
static int init_irq(struct net_device *dev)
{
- int ret = 0;
struct wilc_vif *vif = netdev_priv(dev);
struct wilc *wl = vif->wilc;
-
- ret = gpiod_direction_input(wl->gpio_irq);
- if (ret) {
- netdev_err(dev, "could not obtain gpio for WILC_INTR\n");
- return ret;
- }
-
- wl->dev_irq_num = gpiod_to_irq(wl->gpio_irq);
+ int ret;
ret = request_threaded_irq(wl->dev_irq_num, isr_uh_routine,
isr_bh_routine,
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
"WILC_IRQ", dev);
- if (ret < 0)
- netdev_err(dev, "Failed to request IRQ\n");
- else
- netdev_dbg(dev, "IRQ request succeeded IRQ-NUM= %d\n",
- wl->dev_irq_num);
+ if (ret) {
+ netdev_err(dev, "Failed to request IRQ [%d]\n", ret);
+ return ret;
+ }
+ netdev_dbg(dev, "IRQ request succeeded IRQ-NUM= %d\n", wl->dev_irq_num);
- return ret;
+ return 0;
}
static void deinit_irq(struct net_device *dev)
@@ -501,7 +493,7 @@ static int wilc_wlan_initialize(struct net_device *dev, struct wilc_vif *vif)
if (ret)
goto fail_wilc_wlan;
- if (wl->gpio_irq && init_irq(dev)) {
+ if (wl->dev_irq_num && init_irq(dev)) {
ret = -EIO;
goto fail_threads;
}
diff --git a/drivers/staging/wilc1000/netdev.h b/drivers/staging/wilc1000/netdev.h
index e3689e2a4abb..61cbec674a62 100644
--- a/drivers/staging/wilc1000/netdev.h
+++ b/drivers/staging/wilc1000/netdev.h
@@ -209,7 +209,6 @@ struct wilc {
const struct wilc_hif_func *hif_func;
int io_type;
s8 mac_status;
- struct gpio_desc *gpio_irq;
struct clk *rtc_clk;
bool initialized;
int dev_irq_num;
diff --git a/drivers/staging/wilc1000/sdio.c b/drivers/staging/wilc1000/sdio.c
index 2301e90c21ca..44b426874c1b 100644
--- a/drivers/staging/wilc1000/sdio.c
+++ b/drivers/staging/wilc1000/sdio.c
@@ -8,6 +8,7 @@
#include <linux/mmc/sdio_func.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sdio.h>
+#include <linux/of_irq.h>
#include "netdev.h"
#include "cfg80211.h"
@@ -122,33 +123,32 @@ static int wilc_sdio_probe(struct sdio_func *func,
{
struct wilc *wilc;
int ret;
- struct gpio_desc *gpio = NULL;
struct wilc_sdio *sdio_priv;
sdio_priv = kzalloc(sizeof(*sdio_priv), GFP_KERNEL);
if (!sdio_priv)
return -ENOMEM;
- if (IS_ENABLED(CONFIG_WILC1000_HW_OOB_INTR)) {
- gpio = gpiod_get(&func->dev, "irq", GPIOD_IN);
- if (IS_ERR(gpio)) {
- /* get the GPIO descriptor from hardcode GPIO number */
- gpio = gpio_to_desc(GPIO_NUM);
- if (!gpio)
- dev_err(&func->dev, "failed to get irq gpio\n");
- }
- }
-
ret = wilc_cfg80211_init(&wilc, &func->dev, WILC_HIF_SDIO,
&wilc_hif_sdio);
if (ret) {
kfree(sdio_priv);
return ret;
}
+
+ if (IS_ENABLED(CONFIG_WILC1000_HW_OOB_INTR)) {
+ struct device_node *np = func->card->dev.of_node;
+ int irq_num = of_irq_get(np, 0);
+
+ if (irq_num > 0) {
+ wilc->dev_irq_num = irq_num;
+ sdio_priv->irq_gpio = true;
+ }
+ }
+
sdio_set_drvdata(func, wilc);
wilc->bus_data = sdio_priv;
wilc->dev = &func->dev;
- wilc->gpio_irq = gpio;
wilc->rtc_clk = devm_clk_get(&func->card->dev, "rtc_clk");
if (PTR_ERR_OR_ZERO(wilc->rtc_clk) == -EPROBE_DEFER)
@@ -164,10 +164,6 @@ static void wilc_sdio_remove(struct sdio_func *func)
{
struct wilc *wilc = sdio_get_drvdata(func);
- /* free the GPIO in module remove */
- if (wilc->gpio_irq)
- gpiod_put(wilc->gpio_irq);
-
if (!IS_ERR(wilc->rtc_clk))
clk_disable_unprepare(wilc->rtc_clk);
@@ -592,9 +588,6 @@ static int wilc_sdio_init(struct wilc *wilc, bool resume)
int loop, ret;
u32 chipid;
- if (!resume)
- sdio_priv->irq_gpio = wilc->dev_irq_num;
-
/**
* function 0 csa enable
**/
diff --git a/drivers/staging/wilc1000/spi.c b/drivers/staging/wilc1000/spi.c
index dfd25df75780..852f318a86f0 100644
--- a/drivers/staging/wilc1000/spi.c
+++ b/drivers/staging/wilc1000/spi.c
@@ -151,21 +151,12 @@ static int wilc_bus_probe(struct spi_device *spi)
{
int ret;
struct wilc *wilc;
- struct gpio_desc *gpio;
struct wilc_spi *spi_priv;
spi_priv = kzalloc(sizeof(*spi_priv), GFP_KERNEL);
if (!spi_priv)
return -ENOMEM;
- gpio = gpiod_get(&spi->dev, "irq", GPIOD_IN);
- if (IS_ERR(gpio)) {
- /* get the GPIO descriptor from hardcode GPIO number */
- gpio = gpio_to_desc(GPIO_NUM);
- if (!gpio)
- dev_err(&spi->dev, "failed to get the irq gpio\n");
- }
-
ret = wilc_cfg80211_init(&wilc, &spi->dev, WILC_HIF_SPI, &wilc_hif_spi);
if (ret) {
kfree(spi_priv);
@@ -175,7 +166,7 @@ static int wilc_bus_probe(struct spi_device *spi)
spi_set_drvdata(spi, wilc);
wilc->dev = &spi->dev;
wilc->bus_data = spi_priv;
- wilc->gpio_irq = gpio;
+ wilc->dev_irq_num = spi->irq;
wilc->rtc_clk = devm_clk_get(&spi->dev, "rtc_clk");
if (PTR_ERR_OR_ZERO(wilc->rtc_clk) == -EPROBE_DEFER)
@@ -190,10 +181,6 @@ static int wilc_bus_remove(struct spi_device *spi)
{
struct wilc *wilc = spi_get_drvdata(spi);
- /* free the GPIO in module remove */
- if (wilc->gpio_irq)
- gpiod_put(wilc->gpio_irq);
-
if (!IS_ERR(wilc->rtc_clk))
clk_disable_unprepare(wilc->rtc_clk);
diff --git a/drivers/staging/wilc1000/wlan.h b/drivers/staging/wilc1000/wlan.h
index 5999c5490ea5..7689569cd82f 100644
--- a/drivers/staging/wilc1000/wlan.h
+++ b/drivers/staging/wilc1000/wlan.h
@@ -206,7 +206,6 @@
#define WILC_TX_BUFF_SIZE (64 * 1024)
#define MODALIAS "WILC_SPI"
-#define GPIO_NUM 0x44
#define WILC_PKT_HDR_CONFIG_FIELD BIT(31)
#define WILC_PKT_HDR_OFFSET_FIELD GENMASK(30, 22)
--
2.24.0
On Fri, Mar 6, 2020 at 8:44 AM <[email protected]> wrote:
>
> From: Ajay Singh <[email protected]>
>
> Make use of 'interrupts' property instead of using gpio for handling
> the interrupt as suggested in [1].
>
> [1]. https://lore.kernel.org/linux-wireless/20200303015558.GA6876@bogus/
>
> Signed-off-by: Ajay Singh <[email protected]>
> ---
> .../net/wireless/microchip,wilc1000.yaml | 79 +++++++++++++++++++
> .../wilc1000/microchip,wilc1000,sdio.yaml | 8 +-
> .../wilc1000/microchip,wilc1000,spi.yaml | 8 +-
Bindings should be a separate patch.
> drivers/staging/wilc1000/netdev.c | 24 ++----
> drivers/staging/wilc1000/netdev.h | 1 -
> drivers/staging/wilc1000/sdio.c | 31 +++-----
> drivers/staging/wilc1000/spi.c | 15 +---
> drivers/staging/wilc1000/wlan.h | 1 -
> 8 files changed, 108 insertions(+), 59 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
>
> diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
> new file mode 100644
> index 000000000000..a1914449ad07
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
> @@ -0,0 +1,79 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Microchip WILC wireless devicetree bindings
> +
> +maintainers:
> + - Adham Abozaeid <[email protected]>
> + - Ajay Singh <[email protected]>
> +
> +description:
> + The wilc1000 chips can be connected via SPI or SDIO. This document
> + describes the binding to connect wilc devices.
> +
> +properties:
> + compatible:
> + const: microchip,wilc1000
> +
> + spi-max-frequency:
> + description: Maximum SPI clocking speed of device in Hz.
> + maxItems: 1
No need to redefine a common property. Just:
spi-max-frequency: true
> +
> + reg:
> + description: Chip select address of device.
Drop this.
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + description: phandle to the clock connected on rtc clock line.
> + maxItems: 1
> +
> + clock-names:
> + const: rtc
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +examples:
> + - |
> + spi1: spi@fc018000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + cs-gpios = <&pioB 21 0>;
> + wifi@0 {
> + compatible = "microchip,wilc1000";
> + spi-max-frequency = <48000000>;
> + reg = <0>;
> + interrupt-parent = <&pioC>;
> + interrupts = <27 0>;
> + clocks = <&pck1>;
> + clock-names = "rtc";
> + };
> + };
> +
> + - |
> + mmc1: mmc@fc000000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
> + non-removable;
> + vmmc-supply = <&vcc_mmc1_reg>;
> + vqmmc-supply = <&vcc_3v3_reg>;
> + bus-width = <4>;
> + wifi@0 {
> + compatible = "microchip,wilc1000";
> + reg = <0>;
> + interrupt-parent = <&pioC>;
> + interrupts = <27 0>;
> + clocks = <&pck1>;
> + clock-names = "rtc";
> + };
> + };
> diff --git a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
> index b338f569f7e2..9df7327bc668 100644
> --- a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
> +++ b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
Why aren't you just removing this file and the spi one?
Rob
Hi Rob,
On 06/03/20 9:05 pm, Rob Herring wrote:
>
> On Fri, Mar 6, 2020 at 8:44 AM <[email protected]> wrote:
>>
>> From: Ajay Singh <[email protected]>
>>
>> Make use of 'interrupts' property instead of using gpio for handling
>> the interrupt as suggested in [1].
>>
>> [1]. https://lore.kernel.org/linux-wireless/20200303015558.GA6876@bogus/
>>
>> Signed-off-by: Ajay Singh <[email protected]>
>> ---
>> .../net/wireless/microchip,wilc1000.yaml | 79 +++++++++++++++++++
>> .../wilc1000/microchip,wilc1000,sdio.yaml | 8 +-
>> .../wilc1000/microchip,wilc1000,spi.yaml | 8 +-
>
> Bindings should be a separate patch.
>
Ok. I will add them in separate patch.
>> drivers/staging/wilc1000/netdev.c | 24 ++----
>> drivers/staging/wilc1000/netdev.h | 1 -
>> drivers/staging/wilc1000/sdio.c | 31 +++-----
>> drivers/staging/wilc1000/spi.c | 15 +---
>> drivers/staging/wilc1000/wlan.h | 1 -
>> 8 files changed, 108 insertions(+), 59 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
>> new file mode 100644
>> index 000000000000..a1914449ad07
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
>> @@ -0,0 +1,79 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Microchip WILC wireless devicetree bindings
>> +
>> +maintainers:
>> + - Adham Abozaeid <[email protected]>
>> + - Ajay Singh <[email protected]>
>> +
>> +description:
>> + The wilc1000 chips can be connected via SPI or SDIO. This document
>> + describes the binding to connect wilc devices.
>> +
>> +properties:
>> + compatible:
>> + const: microchip,wilc1000
>> +
>> + spi-max-frequency:
>> + description: Maximum SPI clocking speed of device in Hz.
>> + maxItems: 1
>
> No need to redefine a common property. Just:
>
> spi-max-frequency: true
>
Ok. I will changes this.
>> +
>> + reg:
>> + description: Chip select address of device.
>
> Drop this.
>
Ok.
>> + maxItems: 1
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + clocks:
>> + description: phandle to the clock connected on rtc clock line.
>> + maxItems: 1
>> +
>> + clock-names:
>> + const: rtc
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> +
>> +examples:
>> + - |
>> + spi1: spi@fc018000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + cs-gpios = <&pioB 21 0>;
>> + wifi@0 {
>> + compatible = "microchip,wilc1000";
>> + spi-max-frequency = <48000000>;
>> + reg = <0>;
>> + interrupt-parent = <&pioC>;
>> + interrupts = <27 0>;
>> + clocks = <&pck1>;
>> + clock-names = "rtc";
>> + };
>> + };
>> +
>> + - |
>> + mmc1: mmc@fc000000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
>> + non-removable;
>> + vmmc-supply = <&vcc_mmc1_reg>;
>> + vqmmc-supply = <&vcc_3v3_reg>;
>> + bus-width = <4>;
>> + wifi@0 {
>> + compatible = "microchip,wilc1000";
>> + reg = <0>;
>> + interrupt-parent = <&pioC>;
>> + interrupts = <27 0>;
>> + clocks = <&pck1>;
>> + clock-names = "rtc";
>> + };
>> + };
>> diff --git a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
>> index b338f569f7e2..9df7327bc668 100644
>> --- a/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
>> +++ b/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml
>
> Why aren't you just removing this file and the spi one?
The binding file wrongly got added in this patch. It needs to be added
only to '/driver/staging/wilc1000'. I will update this and send v2
series by keeping binding patch separate from code changes.
Regards,
Ajay