This patch adds support for 6GHz frequency listing.
Signed-off-by: Pradeep Kumar Chitrapu <[email protected]>
---
v5:
- no change
v4:
- no change
v3:
- update channel starting frequency from 5945 to 5950 as per
IEEE P802.11ax/D6.1
drivers/net/wireless/ath/ath11k/mac.c | 71 +++++++++++++++++++++++++++
1 file changed, 71 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 1729e96113ef..45ffe9543c63 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -33,6 +33,15 @@
.max_power = 30, \
}
+#define CHAN6G(_channel, _freq, _flags) { \
+ .band = NL80211_BAND_6GHZ, \
+ .hw_value = (_channel), \
+ .center_freq = (_freq), \
+ .flags = (_flags), \
+ .max_antenna_gain = 0, \
+ .max_power = 30, \
+}
+
/* frame mode values are mapped as per enum ath11k_hw_txrx_mode */
static unsigned int ath11k_frame_mode = ATH11K_HW_TXRX_NATIVE_WIFI;
module_param_named(frame_mode, ath11k_frame_mode, uint, 0644);
@@ -86,6 +95,68 @@ static const struct ieee80211_channel ath11k_5ghz_channels[] = {
CHAN5G(173, 5865, 0),
};
+static const struct ieee80211_channel ath11k_6ghz_channels[] = {
+ CHAN6G(1, 5955, 0),
+ CHAN6G(5, 5975, 0),
+ CHAN6G(9, 5995, 0),
+ CHAN6G(13, 6015, 0),
+ CHAN6G(17, 6035, 0),
+ CHAN6G(21, 6055, 0),
+ CHAN6G(25, 6075, 0),
+ CHAN6G(29, 6095, 0),
+ CHAN6G(33, 6115, 0),
+ CHAN6G(37, 6135, 0),
+ CHAN6G(41, 6155, 0),
+ CHAN6G(45, 6175, 0),
+ CHAN6G(49, 6195, 0),
+ CHAN6G(53, 6215, 0),
+ CHAN6G(57, 6235, 0),
+ CHAN6G(61, 6255, 0),
+ CHAN6G(65, 6275, 0),
+ CHAN6G(69, 6295, 0),
+ CHAN6G(73, 6315, 0),
+ CHAN6G(77, 6335, 0),
+ CHAN6G(81, 6355, 0),
+ CHAN6G(85, 6375, 0),
+ CHAN6G(89, 6395, 0),
+ CHAN6G(93, 6415, 0),
+ CHAN6G(97, 6435, 0),
+ CHAN6G(101, 6455, 0),
+ CHAN6G(105, 6475, 0),
+ CHAN6G(109, 6495, 0),
+ CHAN6G(113, 6515, 0),
+ CHAN6G(117, 6535, 0),
+ CHAN6G(121, 6555, 0),
+ CHAN6G(125, 6575, 0),
+ CHAN6G(129, 6595, 0),
+ CHAN6G(133, 6615, 0),
+ CHAN6G(137, 6635, 0),
+ CHAN6G(141, 6655, 0),
+ CHAN6G(145, 6675, 0),
+ CHAN6G(149, 6695, 0),
+ CHAN6G(153, 6715, 0),
+ CHAN6G(157, 6735, 0),
+ CHAN6G(161, 6755, 0),
+ CHAN6G(165, 6775, 0),
+ CHAN6G(169, 6795, 0),
+ CHAN6G(173, 6815, 0),
+ CHAN6G(177, 6835, 0),
+ CHAN6G(181, 6855, 0),
+ CHAN6G(185, 6875, 0),
+ CHAN6G(189, 6895, 0),
+ CHAN6G(193, 6915, 0),
+ CHAN6G(197, 6935, 0),
+ CHAN6G(201, 6955, 0),
+ CHAN6G(205, 6975, 0),
+ CHAN6G(209, 6995, 0),
+ CHAN6G(213, 7015, 0),
+ CHAN6G(217, 7035, 0),
+ CHAN6G(221, 7055, 0),
+ CHAN6G(225, 7075, 0),
+ CHAN6G(229, 7095, 0),
+ CHAN6G(233, 7115, 0),
+};
+
static struct ieee80211_rate ath11k_legacy_rates[] = {
{ .bitrate = 10,
.hw_value = ATH11K_HW_RATE_CCK_LP_1M },
--
2.17.1
Pradeep Kumar Chitrapu <[email protected]> wrote:
> This patch adds support for 6GHz frequency listing.
>
> Signed-off-by: Pradeep Kumar Chitrapu <[email protected]>
> Signed-off-by: Kalle Valo <[email protected]>
This patchset had new warnings which I fixed in the pending branch:
drivers/net/wireless/ath/ath11k/dp_rx.c:2178: braces {} should be used on all arms of this statement
drivers/net/wireless/ath/ath11k/mac.c:3749: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath11k/mac.c:4197: Blank lines aren't necessary before a close brace '}'
--
https://patchwork.kernel.org/patch/11584701/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Pradeep Kumar Chitrapu <[email protected]> wrote:
> This patch adds support for 6GHz frequency listing.
>
> Signed-off-by: Pradeep Kumar Chitrapu <[email protected]>
> Signed-off-by: Kalle Valo <[email protected]>
8 patches applied to ath-next branch of ath.git, thanks.
c5625abaf826 ath11k: add 6G frequency list supported by driver
22eeadcdeab6 ath11k: add support for 6GHz radio in driver
5dcf42f8b79d ath11k: Use freq instead of channel number in rx path
91270d709b21 ath11k: extend peer_assoc_cmd for 6GHz band
d387503df0cd ath11k: set psc channel flag when sending channel list to firmware.
194b8ea1ce5a ath11k: Add 6G scan dwell time parameter in scan request command
bff621fd113f ath11k: Send multiple scan_chan_list messages if required
74601ecfef6e ath11k: Add support for 6g scan hint
--
https://patchwork.kernel.org/patch/11584701/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches