Shifted the closing */ to the next line
This is done to maintain code uniformity.
Signed-off-by: Shubhankar Kuranagatti <[email protected]>
---
drivers/ssb/main.c | 30 ++++++++++++++++++++----------
1 file changed, 20 insertions(+), 10 deletions(-)
diff --git a/drivers/ssb/main.c b/drivers/ssb/main.c
index 0a26984acb2c..0e180c36daa4 100644
--- a/drivers/ssb/main.c
+++ b/drivers/ssb/main.c
@@ -37,7 +37,8 @@ static LIST_HEAD(buses);
/* Software ID counter */
static unsigned int next_busnumber;
/* buses_mutes locks the two buslists and the next_busnumber.
- * Don't lock this directly, but use ssb_buses_[un]lock() below. */
+ * Don't lock this directly, but use ssb_buses_[un]lock() below.
+ */
static DEFINE_MUTEX(buses_mutex);
/* There are differences in the codeflow, if the bus is
@@ -45,7 +46,8 @@ static DEFINE_MUTEX(buses_mutex);
* are not available early. This is a mechanism to delay
* these initializations to after early boot has finished.
* It's also used to avoid mutex locking, as that's not
- * available and needed early. */
+ * available and needed early.
+ */
static bool ssb_is_early_boot = 1;
static void ssb_buses_lock(void);
@@ -161,7 +163,8 @@ int ssb_bus_resume(struct ssb_bus *bus)
int err;
/* Reset HW state information in memory, so that HW is
- * completely reinitialized. */
+ * completely reinitialized.
+ */
bus->mapped_device = NULL;
#ifdef CONFIG_SSB_DRIVER_PCICORE
bus->pcicore.setup_done = 0;
@@ -467,7 +470,8 @@ static int ssb_devices_register(struct ssb_bus *bus)
sdev = &(bus->devices[i]);
/* We don't register SSB-system devices to the kernel,
- * as the drivers for them are built into SSB. */
+ * as the drivers for them are built into SSB.
+ */
switch (sdev->id.coreid) {
case SSB_DEV_CHIPCOMMON:
case SSB_DEV_PCI:
@@ -521,7 +525,8 @@ static int ssb_devices_register(struct ssb_bus *bus)
if (err) {
pr_err("Could not register %s\n", dev_name(dev));
/* Set dev to NULL to not unregister
- * dev on error unwinding. */
+ * dev on error unwinding.
+ */
sdev->dev = NULL;
put_device(dev);
goto error;
@@ -667,7 +672,8 @@ ssb_bus_register(struct ssb_bus *bus,
ssb_bus_may_powerdown(bus);
/* Queue it for attach.
- * See the comment at the ssb_is_early_boot definition. */
+ * See the comment at the ssb_is_early_boot definition.
+ */
list_add_tail(&bus->list, &attach_queue);
if (!ssb_is_early_boot) {
/* This is not early boot, so we must attach the bus now */
@@ -1007,7 +1013,8 @@ static void ssb_flush_tmslow(struct ssb_device *dev)
* a machine check exception otherwise.
* Do this by reading the register back to commit the
* PCI write and delay an additional usec for the device
- * to react to the change. */
+ * to react to the change.
+ */
ssb_read32(dev, SSB_TMSLOW);
udelay(1);
}
@@ -1044,7 +1051,8 @@ void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags)
EXPORT_SYMBOL(ssb_device_enable);
/* Wait for bitmask in a register to get set or cleared.
- * timeout is in units of ten-microseconds */
+ * timeout is in units of ten-microseconds
+ */
static int ssb_wait_bits(struct ssb_device *dev, u16 reg, u32 bitmask,
int timeout, int set)
{
@@ -1153,7 +1161,8 @@ int ssb_bus_may_powerdown(struct ssb_bus *bus)
/* On buses where more than one core may be working
* at a time, we must not powerdown stuff if there are
- * still cores that may want to run. */
+ * still cores that may want to run.
+ */
if (bus->bustype == SSB_BUSTYPE_SSB)
goto out;
@@ -1322,7 +1331,8 @@ static int __init ssb_modinit(void)
}
/* ssb must be initialized after PCI but before the ssb drivers.
* That means we must use some initcall between subsys_initcall
- * and device_initcall. */
+ * and device_initcall.
+ */
fs_initcall(ssb_modinit);
static void __exit ssb_modexit(void)
--
2.17.1
On Wed, 28 Apr 2021 12:54:53 +0530
Shubhankar Kuranagatti <[email protected]> wrote:
> Shifted the closing */ to the next line
> This is done to maintain code uniformity.
>
> Signed-off-by: Shubhankar Kuranagatti <[email protected]>
Acked-by: Michael Büsch <[email protected]>
--
Michael