Shifted the closing */ to the next line
This is done to maintain code uniformity.
Signed-off-by: Shubhankar Kuranagatti <[email protected]>
---
drivers/ssb/driver_pcicore.c | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/drivers/ssb/driver_pcicore.c b/drivers/ssb/driver_pcicore.c
index c1186415896b..d11b4242b6d2 100644
--- a/drivers/ssb/driver_pcicore.c
+++ b/drivers/ssb/driver_pcicore.c
@@ -55,7 +55,8 @@ void pcicore_write16(struct ssb_pcicore *pc, u16 offset, u16 value)
#include <asm/paccess.h>
/* Probe a 32bit value on the bus and catch bus exceptions.
* Returns nonzero on a bus exception.
- * This is MIPS specific */
+ * This is MIPS specific
+ */
#define mips_busprobe32(val, addr) get_dbe((val), ((u32 *)(addr)))
/* Assume one-hot slot wiring */
@@ -255,7 +256,8 @@ static struct pci_controller ssb_pcicore_controller = {
};
/* This function is called when doing a pci_enable_device().
- * We must first check if the device is a device on the PCI-core bridge. */
+ * We must first check if the device is a device on the PCI-core bridge.
+ */
int ssb_pcicore_plat_dev_init(struct pci_dev *d)
{
if (d->bus->ops != &ssb_pcicore_pciops) {
@@ -381,11 +383,13 @@ static void ssb_pcicore_init_hostmode(struct ssb_pcicore *pc)
/* Ok, ready to run, register it to the system.
* The following needs change, if we want to port hostmode
- * to non-MIPS platform. */
+ * to non-MIPS platform.
+ */
ssb_pcicore_controller.io_map_base = (unsigned long)ioremap(SSB_PCI_MEM, 0x04000000);
set_io_port_base(ssb_pcicore_controller.io_map_base);
/* Give some time to the PCI controller to configure itself with the new
- * values. Not waiting at this point causes crashes of the machine. */
+ * values. Not waiting at this point causes crashes of the machine.
+ */
mdelay(10);
register_pci_controller(&ssb_pcicore_controller);
}
@@ -405,7 +409,8 @@ static int pcicore_is_in_hostmode(struct ssb_pcicore *pc)
return 0;
/* The 200-pin BCM4712 package does not bond out PCI. Even when
- * PCI is bonded out, some boards may leave the pins floating. */
+ * PCI is bonded out, some boards may leave the pins floating.
+ */
if (bus->chip_id == 0x4712) {
if (bus->chip_package == SSB_CHIPPACK_BCM4712S)
return 0;
@@ -685,7 +690,8 @@ int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc,
if (dev->bus->bustype != SSB_BUSTYPE_PCI) {
/* This SSB device is not on a PCI host-bus. So the IRQs are
* not routed through the PCI core.
- * So we must not enable routing through the PCI core. */
+ * So we must not enable routing through the PCI core.
+ */
goto out;
}
--
2.17.1
On Wed, 28 Apr 2021 13:14:32 +0530
Shubhankar Kuranagatti <[email protected]> wrote:
> Shifted the closing */ to the next line
> This is done to maintain code uniformity.
>
> Signed-off-by: Shubhankar Kuranagatti <[email protected]>
Acked-by: Michael Büsch <[email protected]>
--
Michael