v2 -> v3:
- Ran dt_binding_check explicitly to uncover an issue with the
example - I had 2 levels of wifi-firmware{}.. Fixed that..
I hope you folks don't mind me resending so quickly, but it was a
trivial issue. Patch 2 unchanged.
v2: https://lore.kernel.org/r/[email protected]
v1 -> v2:
Dropped:
- '|' in /description
- /properties/resets/minItems
- Unnecessary level of 'items:' in /properties/ext-fem-name
- reserved-memory in examples
- status in examples
- labels in examples
Added:
- /properties/wifi-firmware/additionalProperties: false
- /properties/wifi-firmware/properties/iommus
- /properties/qcom,coexist-support/enum (and reworded the description)
- wifi-firmware and supplies in the SNoC example
Patch 2 is unchanged, picked up rb.
v1: https://lore.kernel.org/r/[email protected]
This is my attempt at (finally) moving ATH10K to YAML.
One inexistent dt property came out as part of that.
Signed-off-by: Konrad Dybcio <[email protected]>
---
Konrad Dybcio (2):
dt-bindings: net: Convert ATH10K to YAML
arm64: dts: qcom: sdm845-polaris: Drop inexistent properties
.../bindings/net/wireless/qcom,ath10k.txt | 215 -------------
.../bindings/net/wireless/qcom,ath10k.yaml | 357 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts | 2 -
3 files changed, 357 insertions(+), 217 deletions(-)
---
base-commit: 8417c8f5007bf4567ccffda850a3157c7d905f67
change-id: 20230406-topic-ath10k_bindings-9af5fa834235
Best regards,
--
Konrad Dybcio <[email protected]>
Convert the ATH10K bindings to YAML.
Dropped properties that are absent at the current state of mainline:
- qcom,msi_addr
- qcom,msi_base
qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
be reconsidered on the driver side, especially the latter one.
Somewhat based on the ath11k bindings.
Signed-off-by: Konrad Dybcio <[email protected]>
---
.../bindings/net/wireless/qcom,ath10k.txt | 215 -------------
.../bindings/net/wireless/qcom,ath10k.yaml | 357 +++++++++++++++++++++
2 files changed, 357 insertions(+), 215 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
deleted file mode 100644
index b61c2d5a0ff7..000000000000
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
+++ /dev/null
@@ -1,215 +0,0 @@
-* Qualcomm Atheros ath10k wireless devices
-
-Required properties:
-- compatible: Should be one of the following:
- * "qcom,ath10k"
- * "qcom,ipq4019-wifi"
- * "qcom,wcn3990-wifi"
-
-PCI based devices uses compatible string "qcom,ath10k" and takes calibration
-data along with board specific data via "qcom,ath10k-calibration-data".
-Rest of the properties are not applicable for PCI based devices.
-
-AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
-and also uses most of the properties defined in this doc (except
-"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
-to carry pre calibration data.
-
-In general, entry "qcom,ath10k-pre-calibration-data" and
-"qcom,ath10k-calibration-data" conflict with each other and only one
-can be provided per device.
-
-SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
-
-- reg: Address and length of the register set for the device.
-- reg-names: Must include the list of following reg names,
- "membase"
-- interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi"
- compatible target.
- reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi"
- compatible target.
- Must contain interrupt-names property per entry for
- "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets.
-
-- interrupt-names: Must include the entries for MSI interrupt
- names ("msi0" to "msi15") and legacy interrupt
- name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi"
- compatible targets.
-
-Optional properties:
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reseti.txt for details.
-- reset-names: Must include the list of following reset names,
- "wifi_cpu_init"
- "wifi_radio_srif"
- "wifi_radio_warm"
- "wifi_radio_cold"
- "wifi_core_warm"
- "wifi_core_cold"
-- clocks: List of clock specifiers, must contain an entry for each required
- entry in clock-names.
-- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
- "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
- "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi"
- compatible target.
-- qcom,msi_addr: MSI interrupt address.
-- qcom,msi_base: Base value to add before writing MSI data into
- MSI address register.
-- qcom,ath10k-calibration-variant: string to search for in the board-2.bin
- variant list with the same bus and device
- specific ids
-- qcom,ath10k-calibration-data : calibration data + board specific data
- as an array, the length can vary between
- hw versions.
-- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
- the length can vary between hw versions.
-- <supply-name>-supply: handle to the regulator device tree node
- optional "supply-name" are "vdd-0.8-cx-mx",
- "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0",
- and "vdd-3.3-ch1".
-- memory-region:
- Usage: optional
- Value type: <phandle>
- Definition: reference to the reserved-memory for the msa region
- used by the wifi firmware running in Q6.
-- iommus:
- Usage: optional
- Value type: <prop-encoded-array>
- Definition: A list of phandle and IOMMU specifier pairs.
-- ext-fem-name:
- Usage: Optional
- Value type: string
- Definition: Name of external front end module used. Some valid FEM names
- for example: "microsemi-lx5586", "sky85703-11"
- and "sky85803" etc.
-- qcom,snoc-host-cap-8bit-quirk:
- Usage: Optional
- Value type: <empty>
- Definition: Quirk specifying that the firmware expects the 8bit version
- of the host capability QMI request
-- qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
-
-- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically
- mapped msa region.
-
-- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex
- support by the hardware.
-- qcom,coexist-gpio-pin : gpio pin number information to support coex
- which will be used by wifi firmware.
-
-* Subnodes
-The ath10k wifi node can contain one optional firmware subnode.
-Firmware subnode is needed when the platform does not have TustZone.
-The firmware subnode must have:
-
-- iommus:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: A list of phandle and IOMMU specifier pairs.
-
-
-Example (to supply PCI based wifi block details):
-
-In this example, the node is defined as child node of the PCI controller.
-
-pci {
- pcie@0 {
- reg = <0 0 0 0 0>;
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
-
- wifi@0,0 {
- reg = <0 0 0 0 0>;
- qcom,ath10k-calibration-data = [ 01 02 03 ... ];
- ext-fem-name = "microsemi-lx5586";
- };
- };
-};
-
-Example (to supply ipq4019 SoC wifi block details):
-
-wifi0: wifi@a000000 {
- compatible = "qcom,ipq4019-wifi";
- reg = <0xa000000 0x200000>;
- resets = <&gcc WIFI0_CPU_INIT_RESET>,
- <&gcc WIFI0_RADIO_SRIF_RESET>,
- <&gcc WIFI0_RADIO_WARM_RESET>,
- <&gcc WIFI0_RADIO_COLD_RESET>,
- <&gcc WIFI0_CORE_WARM_RESET>,
- <&gcc WIFI0_CORE_COLD_RESET>;
- reset-names = "wifi_cpu_init",
- "wifi_radio_srif",
- "wifi_radio_warm",
- "wifi_radio_cold",
- "wifi_core_warm",
- "wifi_core_cold";
- clocks = <&gcc GCC_WCSS2G_CLK>,
- <&gcc GCC_WCSS2G_REF_CLK>,
- <&gcc GCC_WCSS2G_RTC_CLK>;
- clock-names = "wifi_wcss_cmd",
- "wifi_wcss_ref",
- "wifi_wcss_rtc";
- interrupts = <0 0x20 0x1>,
- <0 0x21 0x1>,
- <0 0x22 0x1>,
- <0 0x23 0x1>,
- <0 0x24 0x1>,
- <0 0x25 0x1>,
- <0 0x26 0x1>,
- <0 0x27 0x1>,
- <0 0x28 0x1>,
- <0 0x29 0x1>,
- <0 0x2a 0x1>,
- <0 0x2b 0x1>,
- <0 0x2c 0x1>,
- <0 0x2d 0x1>,
- <0 0x2e 0x1>,
- <0 0x2f 0x1>,
- <0 0xa8 0x0>;
- interrupt-names = "msi0", "msi1", "msi2", "msi3",
- "msi4", "msi5", "msi6", "msi7",
- "msi8", "msi9", "msi10", "msi11",
- "msi12", "msi13", "msi14", "msi15",
- "legacy";
- qcom,msi_addr = <0x0b006040>;
- qcom,msi_base = <0x40>;
- qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
- qcom,coexist-support = <1>;
- qcom,coexist-gpio-pin = <0x33>;
-};
-
-Example (to supply wcn3990 SoC wifi block details):
-
-wifi@18000000 {
- compatible = "qcom,wcn3990-wifi";
- reg = <0x18800000 0x800000>;
- reg-names = "membase";
- clocks = <&clock_gcc clk_rf_clk2_pin>;
- clock-names = "cxo_ref_clk_pin";
- interrupts =
- <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
- vdd-0.8-cx-mx-supply = <&pm8998_l5>;
- vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
- vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
- vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
- vdd-3.3-ch1-supply = <&vreg_l26a_3p3>;
- memory-region = <&wifi_msa_mem>;
- iommus = <&apps_smmu 0x0040 0x1>;
- qcom,msa-fixed-perm;
- wifi-firmware {
- iommus = <&apps_iommu 0xc22 0x1>;
- };
-};
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
new file mode 100644
index 000000000000..323c8c17404b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.yaml
@@ -0,0 +1,357 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/qcom,ath10k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies ATH10K wireless devices
+
+maintainers:
+ - Kalle Valo <[email protected]>
+
+description:
+ Qualcomm Technologies, Inc. IEEE 802.11ac devices.
+
+properties:
+ compatible:
+ enum:
+ - qcom,ath10k # SDIO-based devices
+ - qcom,ipq4019-wifi
+ - qcom,wcn3990-wifi # SNoC-based devices
+
+ reg:
+ maxItems: 1
+
+ reg-names:
+ items:
+ - const: membase
+
+ interrupts:
+ minItems: 12
+ maxItems: 17
+
+ interrupt-names:
+ minItems: 12
+ maxItems: 17
+
+ memory-region:
+ maxItems: 1
+ description:
+ Reference to the MSA memory region used by the Wi-Fi firmware
+ running on the Q6 core.
+
+ iommus:
+ minItems: 1
+ maxItems: 2
+
+ clocks:
+ minItems: 1
+ maxItems: 3
+
+ clock-names:
+ minItems: 1
+ maxItems: 3
+
+ resets:
+ maxItems: 6
+
+ reset-names:
+ items:
+ - const: wifi_cpu_init
+ - const: wifi_radio_srif
+ - const: wifi_radio_warm
+ - const: wifi_radio_cold
+ - const: wifi_core_warm
+ - const: wifi_core_cold
+
+ ext-fem-name:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: Name of external front end module used.
+ enum:
+ - microsemi-lx5586
+ - sky85703-11
+ - sky85803
+
+ wifi-firmware:
+ type: object
+ additionalProperties: false
+ description: |
+ The ATH10K Wi-Fi node can contain one optional firmware subnode.
+ Firmware subnode is needed when the platform does not have Trustzone.
+ properties:
+ iommus:
+ maxItems: 1
+ required:
+ - iommus
+
+ qcom,ath10k-calibration-data:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description:
+ Calibration data + board-specific data as a byte array. The length
+ can vary between hardware versions.
+
+ qcom,ath10k-calibration-variant:
+ $ref: /schemas/types.yaml#/definitions/string
+ description:
+ Unique variant identifier of the calibration data in board-2.bin
+ for designs with colliding bus and device specific ids
+
+ qcom,ath10k-pre-calibration-data:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description:
+ Pre-calibration data as a byte array. The length can vary between
+ hardware versions.
+
+ qcom,coexist-support:
+ $ref: /schemas/types.yaml#/definitions/uint8
+ enum: [0, 1]
+ description:
+ Indicate coex support by the hardware.
+
+ qcom,coexist-gpio-pin:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ COEX GPIO number provided to the Wi-Fi firmware.
+
+ qcom,msa-fixed-perm:
+ type: boolean
+ description:
+ Whether to skip executing an SCM call that reassigns the memory
+ region ownership.
+
+ qcom,smem-states:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: State bits used by the AP to signal the WLAN Q6.
+ items:
+ - description: Signal bits used to enable/disable low power mode
+ on WCN in the case of WoW (Wake on Wireless).
+
+ qcom,smem-state-names:
+ description: The names of the state bits used for SMP2P output.
+ items:
+ - const: wlan-smp2p-out
+
+ qcom,snoc-host-cap-8bit-quirk:
+ type: boolean
+ description:
+ Quirk specifying that the firmware expects the 8bit version
+ of the host capability QMI request
+
+ qcom,xo-cal-data:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ XO cal offset to be configured in XO trim register.
+
+ vdd-0.8-cx-mx-supply:
+ description: Main logic power rail
+
+ vdd-1.8-xo-supply:
+ description: Crystal oscillator supply
+
+ vdd-1.3-rfa-supply:
+ description: RFA supply
+
+ vdd-3.3-ch0-supply:
+ description: Primary Wi-Fi antenna supply
+
+ vdd-3.3-ch1-supply:
+ description: Secondary Wi-Fi antenna supply
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,ipq4019-wifi
+ then:
+ properties:
+ interrupts:
+ minItems: 17
+ maxItems: 17
+
+ interrupt-names:
+ minItems: 17
+ items:
+ - const: msi0
+ - const: msi1
+ - const: msi2
+ - const: msi3
+ - const: msi4
+ - const: msi5
+ - const: msi6
+ - const: msi7
+ - const: msi8
+ - const: msi9
+ - const: msi10
+ - const: msi11
+ - const: msi12
+ - const: msi13
+ - const: msi14
+ - const: msi15
+ - const: legacy
+
+ clocks:
+ items:
+ - description: Wi-Fi command clock
+ - description: Wi-Fi reference clock
+ - description: Wi-Fi RTC clock
+
+ clock-names:
+ items:
+ - const: wifi_wcss_cmd
+ - const: wifi_wcss_ref
+ - const: wifi_wcss_rtc
+
+ required:
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-names
+ - resets
+ - reset-names
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,wcn3990-wifi
+
+ then:
+ properties:
+ clocks:
+ minItems: 1
+ items:
+ - description: XO reference clock
+ - description: Qualcomm Debug Subsystem clock
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: cxo_ref_clk_pin
+ - const: qdss
+
+ interrupts:
+ items:
+ - description: CE0
+ - description: CE1
+ - description: CE2
+ - description: CE3
+ - description: CE4
+ - description: CE5
+ - description: CE6
+ - description: CE7
+ - description: CE8
+ - description: CE9
+ - description: CE10
+ - description: CE11
+
+ required:
+ - interrupts
+
+examples:
+ # SNoC
+ - |
+ #include <dt-bindings/clock/qcom,rpmcc.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ wifi@18800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0x18800000 0x800000>;
+ reg-names = "membase";
+ memory-region = <&wlan_msa_mem>;
+ clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
+ clock-names = "cxo_ref_clk_pin";
+ interrupts = <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&anoc2_smmu 0x1900>,
+ <&anoc2_smmu 0x1901>;
+ qcom,snoc-host-cap-8bit-quirk;
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+ vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+ wifi-firmware {
+ iommus = <&apps_smmu 0x1c02 0x1>;
+ };
+ };
+
+ # AHB
+ - |
+ #include <dt-bindings/clock/qcom,gcc-ipq4019.h>
+
+ wifi@a000000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa000000 0x200000>;
+ resets = <&gcc WIFI0_CPU_INIT_RESET>,
+ <&gcc WIFI0_RADIO_SRIF_RESET>,
+ <&gcc WIFI0_RADIO_WARM_RESET>,
+ <&gcc WIFI0_RADIO_COLD_RESET>,
+ <&gcc WIFI0_CORE_WARM_RESET>,
+ <&gcc WIFI0_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init",
+ "wifi_radio_srif",
+ "wifi_radio_warm",
+ "wifi_radio_cold",
+ "wifi_core_warm",
+ "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS2G_CLK>,
+ <&gcc GCC_WCSS2G_REF_CLK>,
+ <&gcc GCC_WCSS2G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd",
+ "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi0",
+ "msi1",
+ "msi2",
+ "msi3",
+ "msi4",
+ "msi5",
+ "msi6",
+ "msi7",
+ "msi8",
+ "msi9",
+ "msi10",
+ "msi11",
+ "msi12",
+ "msi13",
+ "msi14",
+ "msi15",
+ "legacy";
+ };
--
2.40.0
Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
index 1b7fdbae6a2b..56f2d855df78 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
@@ -712,7 +712,5 @@ &wifi {
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
-
- qcom,snoc-host-cap-skip-quirk;
status = "okay";
};
--
2.40.0
On Thu, 06 Apr 2023 14:55:44 +0200, Konrad Dybcio wrote:
> Convert the ATH10K bindings to YAML.
>
> Dropped properties that are absent at the current state of mainline:
> - qcom,msi_addr
> - qcom,msi_base
>
> qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
> be reconsidered on the driver side, especially the latter one.
>
> Somewhat based on the ath11k bindings.
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> .../bindings/net/wireless/qcom,ath10k.txt | 215 -------------
> .../bindings/net/wireless/qcom,ath10k.yaml | 357 +++++++++++++++++++++
> 2 files changed, 357 insertions(+), 215 deletions(-)
>
Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
wifi@0,0: reg: [[65536, 0, 0, 0, 0], [50397200, 0, 0, 0, 2097152]] is too long
arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-dumo.dtb
wifi@18800000: 'qcom,snoc-host-cap-skip-quirk' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dtb
On 06/04/2023 20:26, Konrad Dybcio wrote:
>>> + interrupts:
>>> + items:
>>> + - description: CE0
>>> + - description: CE1
>>> + - description: CE2
>>> + - description: CE3
>>> + - description: CE4
>>> + - description: CE5
>>> + - description: CE6
>>> + - description: CE7
>>> + - description: CE8
>>> + - description: CE9
>>> + - description: CE10
>>> + - description: CE11
>>
>> What about interrupt-names here? If they are not expected, then just
>> interrupt-names: false
> They obviously wouldn't hurt, but they're unused on the driver side:
>
> for (i = 0; i < CE_COUNT; i++) {
> ret = platform_get_irq(ar_snoc->dev, i);
>
> So I will forbid them.
Assuming DTS does not have them.
Best regards,
Krzysztof
On 6.04.2023 20:30, Krzysztof Kozlowski wrote:
> On 06/04/2023 20:26, Konrad Dybcio wrote:
>
>>>> + interrupts:
>>>> + items:
>>>> + - description: CE0
>>>> + - description: CE1
>>>> + - description: CE2
>>>> + - description: CE3
>>>> + - description: CE4
>>>> + - description: CE5
>>>> + - description: CE6
>>>> + - description: CE7
>>>> + - description: CE8
>>>> + - description: CE9
>>>> + - description: CE10
>>>> + - description: CE11
>>>
>>> What about interrupt-names here? If they are not expected, then just
>>> interrupt-names: false
>> They obviously wouldn't hurt, but they're unused on the driver side:
>>
>> for (i = 0; i < CE_COUNT; i++) {
>> ret = platform_get_irq(ar_snoc->dev, i);
>>
>> So I will forbid them.
>
> Assuming DTS does not have them.
Tested locally, no warnings, so looks like nobody used them in dt.
Konrad
>
> Best regards,
> Krzysztof
>
On Thu, 06 Apr 2023 14:55:43 +0200, Konrad Dybcio wrote:
> v2 -> v3:
> - Ran dt_binding_check explicitly to uncover an issue with the
> example - I had 2 levels of wifi-firmware{}.. Fixed that..
>
> I hope you folks don't mind me resending so quickly, but it was a
> trivial issue. Patch 2 unchanged.
>
> [...]
Applied, thanks!
[2/2] arm64: dts: qcom: sdm845-polaris: Drop inexistent properties
commit: fbc3a1df2866608ca43e7e6d602f66208a5afd88
Best regards,
--
Bjorn Andersson <[email protected]>
On 06/04/2023 14:55, Konrad Dybcio wrote:
> Convert the ATH10K bindings to YAML.
>
> Dropped properties that are absent at the current state of mainline:
> - qcom,msi_addr
> - qcom,msi_base
>
> qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
> be reconsidered on the driver side, especially the latter one.
>
> Somewhat based on the ath11k bindings.
>
> Signed-off-by: Konrad Dybcio <[email protected]>
> ---
> .../bindings/net/wireless/qcom,ath10k.txt | 215 -------------
> .../bindings/net/wireless/qcom,ath10k.yaml | 357 +++++++++++++++++++++
> 2 files changed, 357 insertions(+), 215 deletions(-)
You should have received kernel test robot warning. If not, just
confirming here - you need to fix paths (docs, maintainers).
Best regards,
Krzysztof
On 11.04.2023 17:59, Krzysztof Kozlowski wrote:
> On 06/04/2023 14:55, Konrad Dybcio wrote:
>> Convert the ATH10K bindings to YAML.
>>
>> Dropped properties that are absent at the current state of mainline:
>> - qcom,msi_addr
>> - qcom,msi_base
>>
>> qcom,coexist-support and qcom,coexist-gpio-pin do very little and should
>> be reconsidered on the driver side, especially the latter one.
>>
>> Somewhat based on the ath11k bindings.
>>
>> Signed-off-by: Konrad Dybcio <[email protected]>
>> ---
>> .../bindings/net/wireless/qcom,ath10k.txt | 215 -------------
>> .../bindings/net/wireless/qcom,ath10k.yaml | 357 +++++++++++++++++++++
>> 2 files changed, 357 insertions(+), 215 deletions(-)
>
> You should have received kernel test robot warning. If not, just
> confirming here - you need to fix paths (docs, maintainers).
Will do
Konrad
>
> Best regards,
> Krzysztof
>