From: Sriram R <[email protected]>
With the introduction of Multi Link Operation (MLO) support in
IEEE802.11be, each EHT AP/non AP interface is capable of
operating with multiple radio links.
cfg80211/mac80211 expects drivers to abstract the communication
between such Multi Link HW and mac80211/cfg80211 since it depends
on different driver/HW implementation. Hence the single wiphy
abstraction with changes in datastructures were introduced in
"wifi: ath12k: Introduce hw abstraction"
This patchset extends the implementation to allow combination
of multiple underlying radios into a single composite hw/wiphy
for registration. Since now multiple radios are represented by
a single wiphy, changes are required in various mac ops that the
driver supports since the driver now needs to learn on how to tunnel
various mac ops properly to a specific radio.
This patchset covers the basic mac80211 ops for an interface bringup
and operation.
Note:
Monitor and hw reconfig support for Single Wiphy will be done in future
patchsets.
This patchset is dependent on "[0/3] wifi: ath12k: Refactor the hardware recovery procedures"
---
v2:
- Rebased on ToT and dependent patchset
Karthikeyan Periyasamy (1):
wifi: ath12k: add multiple radio support in a single MAC HW
un/register
Sriram R (11):
wifi: ath12k: Modify add and remove chanctx ops for single wiphy
support
wifi: ath12k: modify ath12k mac start/stop ops for single wiphy
wifi: ath12k: vdev statemachine changes for single wiphy
wifi: ath12k: scan statemachine changes for single wiphy
wifi: ath12k: fetch correct radio based on vdev status
wifi: ath12k: Cache vdev configs before vdev create
wifi: ath12k: Add additional checks for vif and sta iterators
wifi: ath12k: modify regulatory support for single wiphy architecture
wifi: ath12k: Modify set and get antenna mac ops for single wiphy
wifi: ath12k: Modify rts threshold mac op for single wiphy
wifi: ath12k: support get_survey mac op for single wiphy
drivers/net/wireless/ath/ath12k/core.h | 35 +-
drivers/net/wireless/ath/ath12k/hw.h | 1 +
drivers/net/wireless/ath/ath12k/mac.c | 969 +++++++++++++++++++------
drivers/net/wireless/ath/ath12k/reg.c | 60 +-
4 files changed, 836 insertions(+), 229 deletions(-)
--
2.25.1
From: Sriram R <[email protected]>
Modify add and remove chanctx mac80211 ops to fetch the correct
radio(ar) based on channel context.
This change also introduces new helper function to fetch the
radio/ar based on channel context and ieee80211_chan which internally
uses the radio's low/high freq range.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/core.h | 3 ++
drivers/net/wireless/ath/ath12k/mac.c | 51 +++++++++++++++++++++++---
2 files changed, 48 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index 002d4af64335..18269aa0264b 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -596,6 +596,9 @@ struct ath12k {
bool monitor_vdev_created;
bool monitor_started;
int monitor_vdev_id;
+
+ u32 freq_low;
+ u32 freq_high;
};
struct ath12k_hw {
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 69d60e57d660..c58f753d4a10 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -613,6 +613,36 @@ struct ath12k *ath12k_mac_get_ar_by_pdev_id(struct ath12k_base *ab, u32 pdev_id)
return NULL;
}
+static struct ath12k *ath12k_mac_get_ar_by_chan(struct ieee80211_hw *hw,
+ struct ieee80211_channel *channel)
+{
+ struct ath12k_hw *ah = hw->priv;
+ struct ath12k *ar;
+ int i;
+
+ ar = ah->radio;
+
+ if (ah->num_radio == 1)
+ return ar;
+
+ for (i = 0; i < ah->num_radio; i++) {
+ if (channel->center_freq >= ar->freq_low &&
+ channel->center_freq <= ar->freq_high)
+ return ar;
+ ar++;
+ }
+ return NULL;
+}
+
+static struct ath12k *ath12k_get_ar_by_ctx(struct ieee80211_hw *hw,
+ struct ieee80211_chanctx_conf *ctx)
+{
+ if (!ctx)
+ return NULL;
+
+ return ath12k_mac_get_ar_by_chan(hw, ctx->def.chan);
+}
+
static void ath12k_pdev_caps_update(struct ath12k *ar)
{
struct ath12k_base *ab = ar->ab;
@@ -6031,11 +6061,13 @@ static int ath12k_mac_op_ampdu_action(struct ieee80211_hw *hw,
static int ath12k_mac_op_add_chanctx(struct ieee80211_hw *hw,
struct ieee80211_chanctx_conf *ctx)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_ctx(hw, ctx);
+ if (!ar)
+ return -EINVAL;
+
ab = ar->ab;
ath12k_dbg(ab, ATH12K_DBG_MAC,
@@ -6059,11 +6091,13 @@ static int ath12k_mac_op_add_chanctx(struct ieee80211_hw *hw,
static void ath12k_mac_op_remove_chanctx(struct ieee80211_hw *hw,
struct ieee80211_chanctx_conf *ctx)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_ctx(hw, ctx);
+ if (!ar)
+ return;
+
ab = ar->ab;
ath12k_dbg(ab, ATH12K_DBG_MAC,
@@ -6477,11 +6511,13 @@ static void ath12k_mac_op_change_chanctx(struct ieee80211_hw *hw,
struct ieee80211_chanctx_conf *ctx,
u32 changed)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_ctx(hw, ctx);
+ if (!ar)
+ return;
+
ab = ar->ab;
mutex_lock(&ar->conf_mutex);
@@ -7373,6 +7409,9 @@ static void ath12k_mac_update_ch_list(struct ath12k *ar,
band->channels[i].center_freq > freq_high)
band->channels[i].flags |= IEEE80211_CHAN_DISABLED;
}
+
+ ar->freq_low = freq_low;
+ ar->freq_high = freq_high;
}
static u32 ath12k_get_phy_id(struct ath12k *ar, u32 band)
--
2.25.1
From: Sriram R <[email protected]>
When mac80211 does drv start/stop, apply the state change
for all the radios within the wiphy in ath12k.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 57 +++++++++++++++++++++------
1 file changed, 45 insertions(+), 12 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index c58f753d4a10..ef952e8e4086 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -243,6 +243,7 @@ static const u32 ath12k_smps_map[] = {
static int ath12k_start_vdev_delay(struct ath12k *ar,
struct ath12k_vif *arvif);
+static void ath12k_mac_stop(struct ath12k *ar);
static const char *ath12k_mac_phymode_str(enum wmi_phy_mode mode)
{
@@ -5256,15 +5257,31 @@ static int ath12k_mac_start(struct ath12k *ar)
return ret;
}
+static void ath12k_drain_tx(struct ath12k_hw *ah)
+{
+ int i;
+ struct ath12k *ar;
+
+ ar = ah->radio;
+
+ for (i = 0; i < ah->num_radio; i++) {
+ ath12k_mac_drain_tx(ar);
+ ar++;
+ }
+}
+
static int ath12k_mac_op_start(struct ieee80211_hw *hw)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
- struct ath12k *ar = ath12k_ah_to_ar(ah, 0);
- struct ath12k_base *ab = ar->ab;
- int ret;
+ struct ath12k *ar;
+ struct ath12k_base *ab;
+ int ret = 0;
+ int i;
- ath12k_mac_drain_tx(ar);
+ ath12k_drain_tx(ah);
+ ar = ah->radio;
+ ab = ar->ab;
mutex_lock(&ah->conf_mutex);
switch (ah->state) {
@@ -5285,14 +5302,26 @@ static int ath12k_mac_op_start(struct ieee80211_hw *hw)
goto err;
}
- ret = ath12k_mac_start(ar);
- if (ret) {
- ah->state = ATH12K_HW_STATE_OFF;
-
- ath12k_err(ab, "fail to start mac operations in pdev idx %d ret %d\n",
- ar->pdev_idx, ret);
+ for (i = 0; i < ah->num_radio; i++) {
+ ret = ath12k_mac_start(ar);
+ if (ret) {
+ ah->state = ATH12K_HW_STATE_OFF;
+ ath12k_err(ab, "fail to start mac operations in pdev idx %d ret %d\n",
+ ar->pdev_idx, ret);
+ goto fail_start;
+ }
+ ar++;
+ ab = ar->ab;
}
+ mutex_unlock(&ah->conf_mutex);
+
+ return 0;
+fail_start:
+ for (; i > 0; i--) {
+ ar--;
+ ath12k_mac_stop(ar);
+ }
err:
mutex_unlock(&ah->conf_mutex);
@@ -5395,13 +5424,17 @@ static void ath12k_mac_op_stop(struct ieee80211_hw *hw)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar = ath12k_ah_to_ar(ah, 0);
+ int i;
- ath12k_mac_drain_tx(ar);
+ ath12k_drain_tx(ah);
mutex_lock(&ah->conf_mutex);
ah->state = ATH12K_HW_STATE_OFF;
- ath12k_mac_stop(ar);
+ for (i = 0; i < ah->num_radio; i++) {
+ ath12k_mac_stop(ar);
+ ar++;
+ }
mutex_unlock(&ah->conf_mutex);
}
--
2.25.1
From: Sriram R <[email protected]>
Since the vdev create for a corresponding vif is deferred
until a channel is assigned, cache the information which
are received through mac80211 ops between add_interface()
and assign_vif_chanctx() and set them once the vdev is
created on one of the ath12k radios as the channel gets
assigned via assign_vif_chanctx().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/core.h | 19 ++++
drivers/net/wireless/ath/ath12k/mac.c | 116 +++++++++++++++++++------
2 files changed, 107 insertions(+), 28 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index 8088b797419d..009d7b50b5a0 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -214,6 +214,24 @@ enum ath12k_monitor_flags {
ATH12K_FLAG_MONITOR_ENABLED,
};
+struct ath12k_tx_conf {
+ bool changed;
+ u16 ac;
+ struct ieee80211_tx_queue_params tx_queue_params;
+};
+
+struct ath12k_key_conf {
+ bool changed;
+ enum set_key_cmd cmd;
+ struct ieee80211_key_conf *key;
+};
+
+struct ath12k_vif_cache {
+ struct ath12k_tx_conf tx_conf;
+ struct ath12k_key_conf key_conf;
+ u32 bss_conf_changed;
+};
+
struct ath12k_vif {
u32 vdev_id;
enum wmi_vdev_type vdev_type;
@@ -267,6 +285,7 @@ struct ath12k_vif {
u8 tx_encap_type;
u8 vdev_stats_id;
u32 punct_bitmap;
+ struct ath12k_vif_cache cache;
};
struct ath12k_vif_iter {
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index f8e6ac1c4a68..618c75d50547 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -2851,12 +2851,14 @@ static void ath12k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
ar = ath12k_get_ar_by_vif(hw, vif);
- /* TODO if the vdev is not created on a certain radio,
+ /* if the vdev is not created on a certain radio,
* cache the info to be updated later on vdev creation
*/
- if (!ar)
+ if (!ar) {
+ arvif->cache.bss_conf_changed |= changed;
return;
+ }
mutex_lock(&ar->conf_mutex);
@@ -3350,12 +3352,11 @@ static int ath12k_clear_peer_keys(struct ath12k_vif *arvif,
return first_errno;
}
-static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
- struct ieee80211_vif *vif, struct ieee80211_sta *sta,
- struct ieee80211_key_conf *key)
+static int ath12k_mac_set_key(struct ath12k *ar, enum set_key_cmd cmd,
+ struct ieee80211_vif *vif, struct ieee80211_sta *sta,
+ struct ieee80211_key_conf *key)
{
- struct ath12k *ar;
- struct ath12k_base *ab;
+ struct ath12k_base *ab = ar->ab;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_peer *peer;
struct ath12k_sta *arsta;
@@ -3363,28 +3364,11 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
int ret = 0;
u32 flags = 0;
- /* BIP needs to be done in software */
- if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
- key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256)
- return 1;
-
- ar = ath12k_get_ar_by_vif(hw, vif);
- if (!ar) {
- WARN_ON_ONCE(1);
- return -EINVAL;
- }
- ab = ar->ab;
+ lockdep_assert_held(&ar->conf_mutex);
- if (test_bit(ATH12K_FLAG_HW_CRYPTO_DISABLED, &ar->ab->dev_flags))
+ if (test_bit(ATH12K_FLAG_HW_CRYPTO_DISABLED, &ab->dev_flags))
return 1;
- if (key->keyidx > WMI_MAX_KEY_INDEX)
- return -ENOSPC;
-
- mutex_lock(&ar->conf_mutex);
-
if (sta)
peer_addr = sta->addr;
else if (arvif->vdev_type == WMI_VDEV_TYPE_STA)
@@ -3476,6 +3460,43 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
spin_unlock_bh(&ab->base_lock);
exit:
+ return ret;
+}
+
+
+static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
+ struct ieee80211_vif *vif, struct ieee80211_sta *sta,
+ struct ieee80211_key_conf *key)
+{
+ struct ath12k *ar;
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ int ret;
+
+ /* BIP needs to be done in software */
+ if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
+ key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
+ key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
+ key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256)
+ return 1;
+
+ if (key->keyidx > WMI_MAX_KEY_INDEX)
+ return -ENOSPC;
+
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar) {
+ /* ar is expected to be valid when sta ptr is available */
+ if (sta) {
+ WARN_ON_ONCE(1);
+ return -EINVAL;
+ }
+ arvif->cache.key_conf.cmd = cmd;
+ arvif->cache.key_conf.key = key;
+ arvif->cache.key_conf.changed = true;
+ return 0;
+ }
+
+ mutex_lock(&ar->conf_mutex);
+ ret = ath12k_mac_set_key(ar, cmd, vif, sta, key);
mutex_unlock(&ar->conf_mutex);
return ret;
}
@@ -4303,7 +4324,10 @@ static int ath12k_mac_op_conf_tx(struct ieee80211_hw *hw,
ar = ath12k_get_ar_by_vif(hw, vif);
if (!ar) {
- /* TODO cache the info and apply after vdev is created */
+ /* cache the info and apply after vdev is created */
+ arvif->cache.tx_conf.changed = true;
+ arvif->cache.tx_conf.ac = ac;
+ arvif->cache.tx_conf.tx_queue_params = *params;
return -EINVAL;
}
@@ -5941,6 +5965,41 @@ static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
return ret;
}
+static void ath12k_mac_vif_cache_flush(struct ath12k *ar, struct ieee80211_vif *vif)
+{
+ struct ath12k_base *ab = ar->ab;
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ int ret;
+
+ lockdep_assert_held(&ar->conf_mutex);
+
+ if (arvif->cache.tx_conf.changed) {
+ ret = ath12k_mac_conf_tx(arvif, 0, arvif->cache.tx_conf.ac,
+ &arvif->cache.tx_conf.tx_queue_params);
+ if (ret)
+ ath12k_warn(ab,
+ "unable to apply tx config parameters to vdev %d\n",
+ ret);
+ }
+
+ if (arvif->cache.bss_conf_changed)
+ ath12k_mac_bss_info_changed(ar, arvif, &vif->bss_conf,
+ arvif->cache.bss_conf_changed);
+
+ if (arvif->cache.key_conf.changed) {
+ ret = ath12k_mac_set_key(ar, arvif->cache.key_conf.cmd,
+ vif, NULL,
+ arvif->cache.key_conf.key);
+ if (ret) {
+ WARN_ON_ONCE(1);
+ ath12k_warn(ab, "unable to apply set key param to vdev %d ret %d\n",
+ arvif->vdev_id, ret);
+ }
+ }
+
+ memset(&arvif->cache, 0, sizeof(struct ath12k_vif_cache));
+}
+
static struct ath12k *ath12k_mac_assign_vif_to_vdev(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_chanctx_conf *ctx)
@@ -6023,10 +6082,11 @@ static struct ath12k *ath12k_mac_assign_vif_to_vdev(struct ieee80211_hw *hw,
goto unlock;
}
- /* TODO If the vdev is created during channel assign and not during
+ /* If the vdev is created during channel assign and not during
* add_interface(), Apply any parameters for the vdev which were received
* after add_interface, corresponding to this vif.
*/
+ ath12k_mac_vif_cache_flush(ar, vif);
unlock:
mutex_unlock(&ar->conf_mutex);
out:
--
2.25.1
From: Sriram R <[email protected]>
Since vif and sta objects of different radios are added to same
local hw list in mac80211, additional checks need to be done
in driver to ensure we are processing the intended vif
and sta corresponding to the radio when the vif and sta mac80211
iterator utils are used from driver.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/core.h | 1 +
drivers/net/wireless/ath/ath12k/mac.c | 22 ++++++++++++++++++++--
2 files changed, 21 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index 009d7b50b5a0..d41f8e5915f6 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -290,6 +290,7 @@ struct ath12k_vif {
struct ath12k_vif_iter {
u32 vdev_id;
+ struct ath12k *ar;
struct ath12k_vif *arvif;
};
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 618c75d50547..631b24c6e435 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -533,7 +533,8 @@ static void ath12k_get_arvif_iter(void *data, u8 *mac,
struct ath12k_vif_iter *arvif_iter = data;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
- if (arvif->vdev_id == arvif_iter->vdev_id)
+ if (arvif->vdev_id == arvif_iter->vdev_id &&
+ arvif->ar == arvif_iter->ar)
arvif_iter->arvif = arvif;
}
@@ -543,6 +544,7 @@ struct ath12k_vif *ath12k_mac_get_arvif(struct ath12k *ar, u32 vdev_id)
u32 flags;
arvif_iter.vdev_id = vdev_id;
+ arvif_iter.ar = ar;
flags = IEEE80211_IFACE_ITER_RESUME_ALL;
ieee80211_iterate_active_interfaces_atomic(ath12k_ar_to_hw(ar),
@@ -6678,14 +6680,19 @@ struct ath12k_mac_change_chanctx_arg {
struct ieee80211_vif_chanctx_switch *vifs;
int n_vifs;
int next_vif;
+ struct ath12k *ar;
};
static void
ath12k_mac_change_chanctx_cnt_iter(void *data, u8 *mac,
struct ieee80211_vif *vif)
{
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_mac_change_chanctx_arg *arg = data;
+ if (arvif->ar != arg->ar)
+ return;
+
if (rcu_access_pointer(vif->bss_conf.chanctx_conf) != arg->ctx)
return;
@@ -6696,9 +6703,13 @@ static void
ath12k_mac_change_chanctx_fill_iter(void *data, u8 *mac,
struct ieee80211_vif *vif)
{
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_mac_change_chanctx_arg *arg = data;
struct ieee80211_chanctx_conf *ctx;
+ if (arvif->ar != arg->ar)
+ return;
+
ctx = rcu_access_pointer(vif->bss_conf.chanctx_conf);
if (ctx != arg->ctx)
return;
@@ -6815,7 +6826,7 @@ static void
ath12k_mac_update_active_vif_chan(struct ath12k *ar,
struct ieee80211_chanctx_conf *ctx)
{
- struct ath12k_mac_change_chanctx_arg arg = { .ctx = ctx };
+ struct ath12k_mac_change_chanctx_arg arg = { .ctx = ctx, .ar = ar };
struct ieee80211_hw *hw = ath12k_ar_to_hw(ar);
lockdep_assert_held(&ar->conf_mutex);
@@ -7391,6 +7402,9 @@ static void ath12k_mac_set_bitrate_mask_iter(void *data,
struct ath12k_sta *arsta = ath12k_sta_to_arsta(sta);
struct ath12k *ar = arvif->ar;
+ if (arsta->arvif != arvif)
+ return;
+
spin_lock_bh(&ar->data_lock);
arsta->changed |= IEEE80211_RC_SUPP_RATES_CHANGED;
spin_unlock_bh(&ar->data_lock);
@@ -7401,10 +7415,14 @@ static void ath12k_mac_set_bitrate_mask_iter(void *data,
static void ath12k_mac_disable_peer_fixed_rate(void *data,
struct ieee80211_sta *sta)
{
+ struct ath12k_sta *arsta = ath12k_sta_to_arsta(sta);
struct ath12k_vif *arvif = data;
struct ath12k *ar = arvif->ar;
int ret;
+ if (arsta->arvif != arvif)
+ return;
+
ret = ath12k_wmi_set_peer_param(ar, sta->addr,
arvif->vdev_id,
WMI_PEER_PARAM_FIXED_RATE,
--
2.25.1
From: Sriram R <[email protected]>
As multiple radios are combined into a single wiphy, and
the current infrastructure supports only set/get antenna
for the wiphy, the max Tx/Rx antenna capability is advertised
during wiphy register.
Hence, When antenna set/get is received we adjust the set/get
based on max radio capability and set/get antenna accordingly.
Multi radio capability needs to introduced with interface
combination changes to support single wiphy model in cfg80211
which would help extend the wiphy specific get/set configs similar
to this to per hw level.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 37 ++++++++++++++++++++-------
1 file changed, 28 insertions(+), 9 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 617dd55e7d4e..a85468cc63da 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -5010,6 +5010,13 @@ static int __ath12k_set_antenna(struct ath12k *ar, u32 tx_ant, u32 rx_ant)
if (ath12k_check_chain_mask(ar, rx_ant, false))
return -EINVAL;
+ /* Since we advertised the max cap of all radios combined during wiphy
+ * registration, ensure we don't set the antenna config higher than the
+ * limits
+ */
+ tx_ant = min_t(u32, tx_ant, ar->pdev->cap.tx_chain_mask);
+ rx_ant = min_t(u32, rx_ant, ar->pdev->cap.rx_chain_mask);
+
ar->cfg_tx_chainmask = tx_ant;
ar->cfg_rx_chainmask = rx_ant;
@@ -6309,16 +6316,22 @@ static void ath12k_mac_op_configure_filter(struct ieee80211_hw *hw,
static int ath12k_mac_op_get_antenna(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
+ int antennas_rx = 0, antennas_tx = 0;
struct ath12k *ar;
+ int i;
ar = ath12k_ah_to_ar(ah, 0);
- mutex_lock(&ar->conf_mutex);
-
- *tx_ant = ar->cfg_tx_chainmask;
- *rx_ant = ar->cfg_rx_chainmask;
+ for (i = 0; i < ah->num_radio; i++) {
+ mutex_lock(&ar->conf_mutex);
+ antennas_rx = max_t(u32, antennas_rx, ar->cfg_rx_chainmask);
+ antennas_tx = max_t(u32, antennas_tx, ar->cfg_tx_chainmask);
+ mutex_unlock(&ar->conf_mutex);
+ ar++;
+ }
- mutex_unlock(&ar->conf_mutex);
+ *tx_ant = antennas_tx;
+ *rx_ant = antennas_rx;
return 0;
}
@@ -6327,13 +6340,19 @@ static int ath12k_mac_op_set_antenna(struct ieee80211_hw *hw, u32 tx_ant, u32 rx
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
- int ret;
+ int ret = 0;
+ int i;
ar = ath12k_ah_to_ar(ah, 0);
- mutex_lock(&ar->conf_mutex);
- ret = __ath12k_set_antenna(ar, tx_ant, rx_ant);
- mutex_unlock(&ar->conf_mutex);
+ for (i = 0; i < ah->num_radio; i++) {
+ mutex_lock(&ar->conf_mutex);
+ ret = __ath12k_set_antenna(ar, tx_ant, rx_ant);
+ mutex_unlock(&ar->conf_mutex);
+ if (ret)
+ break;
+ ar++;
+ }
return ret;
}
--
2.25.1
From: Sriram R <[email protected]>
With all the radios being combined and registered as a single
mac80211 hw/wiphy, separate regd built from firmware rules need
not be updated to cfg80211. Rather we can pick one of the regd
built from the rules to update to cfg80211 for the whole
registered device. We prefer 6 GHz pdev based rules since it has
the rules for all bands. If the hw doesn't support 6 GHz, then update
rules from one of the pdevs.
Also, when regulatory notification is received, update to all the
underlying radios/ar so that it becomes aware of the change and as
well us it updates its local regd with the new country rules. Later
pick the appropriate pdev's regd(6 GHz if available) and apply to
cfg80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/core.h | 2 +
drivers/net/wireless/ath/ath12k/mac.c | 2 +
drivers/net/wireless/ath/ath12k/reg.c | 58 ++++++++++++++++++++++----
3 files changed, 53 insertions(+), 9 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index d41f8e5915f6..01232679795c 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -632,6 +632,8 @@ struct ath12k_hw {
u8 num_radio;
+ bool regd_updated;
+ bool use_6ghz_regd;
/* Keep last */
struct ath12k radio[] __aligned(sizeof(void *));
};
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 631b24c6e435..617dd55e7d4e 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -7829,6 +7829,7 @@ static int ath12k_mac_setup_channels_rates(struct ath12k *ar,
struct ath12k_wmi_hal_reg_capabilities_ext_arg *reg_cap;
void *channels;
u32 phy_id;
+ struct ath12k_hw *ah = ar->ah;
BUILD_BUG_ON((ARRAY_SIZE(ath12k_2ghz_channels) +
ARRAY_SIZE(ath12k_5ghz_channels) +
@@ -7881,6 +7882,7 @@ static int ath12k_mac_setup_channels_rates(struct ath12k *ar,
ath12k_mac_update_ch_list(ar, band,
reg_cap->low_5ghz_chan,
reg_cap->high_5ghz_chan);
+ ah->use_6ghz_regd = true;
}
if (reg_cap->low_5ghz_chan < ATH12K_MIN_6G_FREQ) {
diff --git a/drivers/net/wireless/ath/ath12k/reg.c b/drivers/net/wireless/ath/ath12k/reg.c
index e44723d9d0b2..1df8a2bfcddd 100644
--- a/drivers/net/wireless/ath/ath12k/reg.c
+++ b/drivers/net/wireless/ath/ath12k/reg.c
@@ -50,7 +50,7 @@ ath12k_reg_notifier(struct wiphy *wiphy, struct regulatory_request *request)
struct ath12k_wmi_init_country_arg arg;
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar = ath12k_ah_to_ar(ah, 0);
- int ret;
+ int ret, i;
ath12k_dbg(ar->ab, ATH12K_DBG_REG,
"Regulatory Notification received for %s\n", wiphy_name(wiphy));
@@ -85,10 +85,17 @@ ath12k_reg_notifier(struct wiphy *wiphy, struct regulatory_request *request)
memcpy(&arg.cc_info.alpha2, request->alpha2, 2);
arg.cc_info.alpha2[2] = 0;
- ret = ath12k_wmi_send_init_country_cmd(ar, &arg);
- if (ret)
- ath12k_warn(ar->ab,
- "INIT Country code set to fw failed : %d\n", ret);
+ /* Allow fresh updates to wiphy regd */
+ ah->regd_updated = false;
+
+ /* Send the reg change request to all the radios */
+ for (i = 0; i < ah->num_radio; i++) {
+ ret = ath12k_wmi_send_init_country_cmd(ar, &arg);
+ if (ret)
+ ath12k_warn(ar->ab,
+ "INIT Country code set to fw failed : %d\n", ret);
+ ar++;
+ }
}
int ath12k_reg_update_chan_list(struct ath12k *ar)
@@ -205,8 +212,29 @@ int ath12k_regd_update(struct ath12k *ar, bool init)
struct ieee80211_regdomain *regd, *regd_copy = NULL;
int ret, regd_len, pdev_id;
struct ath12k_base *ab;
+ int i;
ab = ar->ab;
+
+ /* If one of the radios within ah has already updated the regd for
+ * the wiphy, then avoid setting regd again
+ */
+ if (ah->regd_updated)
+ return 0;
+
+ /* firmware provides reg rules which are similar for 2 GHz and 5 GHz
+ * pdev but 6 GHz pdev has superset of all rules including rules for
+ * all bands, we prefer 6 GHz pdev's rules to be used for setup of
+ * the wiphy regd.
+ * If 6 GHz pdev was part of the ath12k_hw, wait for the 6 GHz pdev,
+ * else pick the first pdev which calls this function and use its
+ * regd to update global hw regd.
+ * The regd_updated flag set at the end will not allow any further
+ * updates.
+ */
+ if (ah->use_6ghz_regd && !ar->supports_6ghz)
+ return 0;
+
pdev_id = ar->pdev_idx;
spin_lock_bh(&ab->base_lock);
@@ -259,10 +287,22 @@ int ath12k_regd_update(struct ath12k *ar, bool init)
if (ret)
goto err;
- if (ah->state == ATH12K_HW_STATE_ON) {
- ret = ath12k_reg_update_chan_list(ar);
- if (ret)
- goto err;
+ ah->regd_updated = true;
+
+ /* Apply the new regd to all the radios, this is expected to be received only once
+ * since we check for ah->regd_updated and allow here only once
+ */
+ ar = ah->radio;
+ ab = ar->ab;
+
+ for (i = 0; i < ah->num_radio; i++) {
+ if (ah->state == ATH12K_HW_STATE_ON) {
+ ret = ath12k_reg_update_chan_list(ar);
+ if (ret)
+ goto err;
+ }
+ ar++;
+ ab = ar->ab;
}
return 0;
--
2.25.1
From: Sriram R <[email protected]>
The radio for which the survey info needs to be collected
depends on the channel idx which could be based on the band.
Use the idx to identify the appropriate sband since multiple
bands could be combined for single wiphy case.
Also use the channel idx and sband to identify the corresponding
radio on which the survey results needs to be populated.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 25 ++++++++++++++++---------
1 file changed, 16 insertions(+), 9 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 1e1de27e5d14..8f867fb99b5f 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -7702,7 +7702,6 @@ ath12k_mac_update_bss_chan_survey(struct ath12k *ar,
static int ath12k_mac_op_get_survey(struct ieee80211_hw *hw, int idx,
struct survey_info *survey)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ieee80211_supported_band *sband;
struct survey_info *ar_survey;
@@ -7711,12 +7710,6 @@ static int ath12k_mac_op_get_survey(struct ieee80211_hw *hw, int idx,
if (idx >= ATH12K_NUM_CHANS)
return -ENOENT;
- ar = ath12k_ah_to_ar(ah, 0);
-
- ar_survey = &ar->survey[idx];
-
- mutex_lock(&ar->conf_mutex);
-
sband = hw->wiphy->bands[NL80211_BAND_2GHZ];
if (sband && idx >= sband->n_channels) {
idx -= sband->n_channels;
@@ -7731,6 +7724,21 @@ static int ath12k_mac_op_get_survey(struct ieee80211_hw *hw, int idx,
goto exit;
}
+ ar = ath12k_mac_get_ar_by_chan(hw, &sband->channels[idx]);
+ if (!ar) {
+ if (sband->channels[idx].flags & IEEE80211_CHAN_DISABLED) {
+ ret = 0;
+ memset(survey, 0, sizeof(*survey));
+ goto exit;
+ }
+ ret = -ENOENT;
+ goto exit;
+ }
+
+ ar_survey = &ar->survey[idx];
+
+ mutex_lock(&ar->conf_mutex);
+
ath12k_mac_update_bss_chan_survey(ar, &sband->channels[idx]);
spin_lock_bh(&ar->data_lock);
@@ -7742,9 +7750,8 @@ static int ath12k_mac_op_get_survey(struct ieee80211_hw *hw, int idx,
if (ar->rx_channel == survey->channel)
survey->filled |= SURVEY_INFO_IN_USE;
-exit:
mutex_unlock(&ar->conf_mutex);
-
+exit:
return ret;
}
--
2.25.1
From: Sriram R <[email protected]>
Since multiple radios are abstracted under a single wiphy,
apply the rts threshold value to all the vdevs of the radios
combined under single wiphy.
This also implies that vif specific rts threshold support
needs to be added in future from cfg80211/mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 17 +++++++++++++++--
1 file changed, 15 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index a85468cc63da..1e1de27e5d14 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -7153,11 +7153,24 @@ static int ath12k_mac_op_set_rts_threshold(struct ieee80211_hw *hw, u32 value)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
- int param_id = WMI_VDEV_PARAM_RTS_THRESHOLD, ret;
+ int param_id = WMI_VDEV_PARAM_RTS_THRESHOLD, ret, i;
ar = ath12k_ah_to_ar(ah, 0);
- ret = ath12k_set_vdev_param_to_all_vifs(ar, param_id, value);
+ /* Currently we set the rts threshold value to all the vifs across
+ * all radios of the single wiphy.
+ * TODO Once support for vif specific RTS threshold in mac80211 is
+ * available, ath12k can make use of it.
+ */
+ for (i = 0; i < ah->num_radio; i++) {
+ ret = ath12k_set_vdev_param_to_all_vifs(ar, param_id, value);
+ if (ret) {
+ ath12k_warn(ar->ab, "failed to set RTS config for all vdevs of pdev %d",
+ ar->pdev->pdev_id);
+ break;
+ }
+ ar++;
+ }
return ret;
}
--
2.25.1
From: Sriram R <[email protected]>
With single wiphy, multiple radios are combined into a single wiphy.
Since any channel can be assigned to a vif being brought up,
the vdev cannot be created during add_interface(). Hence defer the
vdev creation till channel assignment.
If only one radio is part of the wiphy, then the existing logic
is maintained, i.e vdevs are created during add interface and
started during channel assignment. This ensures no functional changes
to single pdev devices which has only one radio in the SoC.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/core.h | 1 +
drivers/net/wireless/ath/ath12k/hw.h | 1 +
drivers/net/wireless/ath/ath12k/mac.c | 203 +++++++++++++++++--------
3 files changed, 144 insertions(+), 61 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index 18269aa0264b..8088b797419d 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -251,6 +251,7 @@ struct ath12k_vif {
} ap;
} u;
+ bool is_created;
bool is_started;
bool is_up;
u32 aid;
diff --git a/drivers/net/wireless/ath/ath12k/hw.h b/drivers/net/wireless/ath/ath12k/hw.h
index 2e9c3b05d75a..64d116ef8745 100644
--- a/drivers/net/wireless/ath/ath12k/hw.h
+++ b/drivers/net/wireless/ath/ath12k/hw.h
@@ -80,6 +80,7 @@
#define TARGET_RX_PEER_METADATA_VER_V1A 2
#define TARGET_RX_PEER_METADATA_VER_V1B 3
+#define ATH12K_HW_DEFAULT_QUEUE 0
#define ATH12K_HW_MAX_QUEUES 4
#define ATH12K_QUEUE_LEN 4096
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index ef952e8e4086..b723226c7577 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -5609,64 +5609,24 @@ static void ath12k_mac_op_update_vif_offload(struct ieee80211_hw *hw,
ath12k_mac_update_vif_offload(arvif);
}
-static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
- struct ieee80211_vif *vif)
+static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
- struct ath12k *ar;
- struct ath12k_base *ab;
+ struct ath12k_hw *ah = ar->ah;
+ struct ath12k_base *ab = ar->ab;
+ struct ieee80211_hw *hw = ah->hw;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_wmi_vdev_create_arg vdev_arg = {0};
struct ath12k_wmi_peer_create_arg peer_param;
u32 param_id, param_value;
u16 nss;
int i;
- int ret;
- int bit;
-
- vif->driver_flags |= IEEE80211_VIF_SUPPORTS_UAPSD;
+ int ret, vdev_id;
- ar = ath12k_ah_to_ar(ah, 0);
- ab = ar->ab;
-
- mutex_lock(&ar->conf_mutex);
-
- if (vif->type == NL80211_IFTYPE_AP &&
- ar->num_peers > (ar->max_num_peers - 1)) {
- ath12k_warn(ab, "failed to create vdev due to insufficient peer entry resource in firmware\n");
- ret = -ENOBUFS;
- goto err;
- }
-
- if (ar->num_created_vdevs > (TARGET_NUM_VDEVS - 1)) {
- ath12k_warn(ab, "failed to create vdev, reached max vdev limit %d\n",
- TARGET_NUM_VDEVS);
- ret = -EBUSY;
- goto err;
- }
-
- memset(arvif, 0, sizeof(*arvif));
+ lockdep_assert_held(&ar->conf_mutex);
arvif->ar = ar;
- arvif->vif = vif;
-
- INIT_LIST_HEAD(&arvif->list);
-
- /* Should we initialize any worker to handle connection loss indication
- * from firmware in sta mode?
- */
-
- for (i = 0; i < ARRAY_SIZE(arvif->bitrate_mask.control); i++) {
- arvif->bitrate_mask.control[i].legacy = 0xffffffff;
- memset(arvif->bitrate_mask.control[i].ht_mcs, 0xff,
- sizeof(arvif->bitrate_mask.control[i].ht_mcs));
- memset(arvif->bitrate_mask.control[i].vht_mcs, 0xff,
- sizeof(arvif->bitrate_mask.control[i].vht_mcs));
- }
-
- bit = __ffs64(ab->free_vdev_map);
-
- arvif->vdev_id = bit;
+ vdev_id = __ffs64(ab->free_vdev_map);
+ arvif->vdev_id = vdev_id;
arvif->vdev_subtype = WMI_VDEV_SUBTYPE_NONE;
switch (vif->type) {
@@ -5682,14 +5642,14 @@ static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
break;
case NL80211_IFTYPE_MONITOR:
arvif->vdev_type = WMI_VDEV_TYPE_MONITOR;
- ar->monitor_vdev_id = bit;
+ ar->monitor_vdev_id = vdev_id;
break;
default:
WARN_ON(1);
break;
}
- ath12k_dbg(ar->ab, ATH12K_DBG_MAC, "mac add interface id %d type %d subtype %d map %llx\n",
+ ath12k_dbg(ar->ab, ATH12K_DBG_MAC, "mac vdev create id %d type %d subtype %d map %llx\n",
arvif->vdev_id, arvif->vdev_type, arvif->vdev_subtype,
ab->free_vdev_map);
@@ -5707,6 +5667,7 @@ static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
}
ar->num_created_vdevs++;
+ arvif->is_created = true;
ath12k_dbg(ab, ATH12K_DBG_MAC, "vdev %pM created, vdev_id %d\n",
vif->addr, arvif->vdev_id);
ar->allocated_vdev_map |= 1LL << arvif->vdev_id;
@@ -5807,8 +5768,6 @@ static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
if (vif->type != NL80211_IFTYPE_MONITOR && ar->monitor_conf_enabled)
ath12k_mac_monitor_vdev_create(ar);
- mutex_unlock(&ar->conf_mutex);
-
return ret;
err_peer_del:
@@ -5834,6 +5793,7 @@ static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
err_vdev_del:
ath12k_wmi_vdev_delete(ar, arvif->vdev_id);
ar->num_created_vdevs--;
+ arvif->is_created = false;
ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
ab->free_vdev_map |= 1LL << arvif->vdev_id;
ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
@@ -5842,9 +5802,104 @@ static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
spin_unlock_bh(&ar->data_lock);
err:
+ arvif->ar = NULL;
+ return ret;
+}
+
+static struct ath12k *ath12k_mac_assign_vif_to_vdev(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_chanctx_conf *ctx)
+{
+ struct ath12k_hw *ah = hw->priv;
+ struct ath12k *ar;
+ struct ath12k_base *ab;
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ u8 bit;
+ int ret;
+
+ if (arvif->ar) {
+ WARN_ON(!arvif->is_created);
+ goto out;
+ }
+
+ if (ah->num_radio == 1)
+ ar = ah->radio;
+ else if (ctx)
+ ar = ath12k_get_ar_by_ctx(hw, ctx);
+ else
+ return NULL;
+
+ if (!ar)
+ goto out;
+
+ ab = ar->ab;
+
+ mutex_lock(&ar->conf_mutex);
+
+ if (vif->type == NL80211_IFTYPE_AP &&
+ ar->num_peers > (ar->max_num_peers - 1)) {
+ ath12k_warn(ab, "failed to create vdev due to insufficient peer entry resource in firmware\n");
+ ret = -ENOBUFS;
+ goto unlock;
+ }
+
+ if (ar->num_created_vdevs > (TARGET_NUM_VDEVS - 1)) {
+ ath12k_warn(ab, "failed to create vdev, reached max vdev limit %d\n",
+ TARGET_NUM_VDEVS);
+ ret = -EBUSY;
+ goto unlock;
+ }
+
+ ret = ath12k_mac_vdev_create(ar, vif);
+ if (ret) {
+ ath12k_warn(ab, "failed to create vdev %d ret %d", bit, ret);
+ goto unlock;
+ }
+
+ /* TODO If the vdev is created during channel assign and not during
+ * add_interface(), Apply any parameters for the vdev which were received
+ * after add_interface, corresponding to this vif.
+ */
+unlock:
mutex_unlock(&ar->conf_mutex);
+out:
+ return arvif->ar;
+}
- return ret;
+static int ath12k_mac_op_add_interface(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif)
+{
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ int i;
+
+ memset(arvif, 0, sizeof(*arvif));
+
+ arvif->vif = vif;
+
+ INIT_LIST_HEAD(&arvif->list);
+
+ for (i = 0; i < ARRAY_SIZE(arvif->bitrate_mask.control); i++) {
+ arvif->bitrate_mask.control[i].legacy = 0xffffffff;
+ memset(arvif->bitrate_mask.control[i].ht_mcs, 0xff,
+ sizeof(arvif->bitrate_mask.control[i].ht_mcs));
+ memset(arvif->bitrate_mask.control[i].vht_mcs, 0xff,
+ sizeof(arvif->bitrate_mask.control[i].vht_mcs));
+ }
+
+ /* Allocate Default Queue now and reassign during actual vdev create */
+ vif->cab_queue = ATH12K_HW_DEFAULT_QUEUE;
+ for (i = 0; i < ARRAY_SIZE(vif->hw_queue); i++)
+ vif->hw_queue[i] = ATH12K_HW_DEFAULT_QUEUE;
+
+ vif->driver_flags |= IEEE80211_VIF_SUPPORTS_UAPSD;
+
+ /* For single radio wiphy(i.e ah->num_radio is 1), create the vdev
+ * during add_interface itself, for multi radio wiphy, defer the vdev
+ * creation until channel_assign to determine the radio on which the
+ * vdev needs to be created
+ */
+ ath12k_mac_assign_vif_to_vdev(hw, vif, NULL);
+ return 0;
}
static void ath12k_mac_vif_unref(struct ath12k_dp *dp, struct ieee80211_vif *vif)
@@ -5875,14 +5930,16 @@ static void ath12k_mac_vif_unref(struct ath12k_dp *dp, struct ieee80211_vif *vif
static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_base *ab;
unsigned long time_left;
int ret;
- ar = ath12k_ah_to_ar(ah, 0);
+ if (!arvif->is_created)
+ return;
+
+ ar = arvif->ar;
ab = ar->ab;
mutex_lock(&ar->conf_mutex);
@@ -5924,6 +5981,7 @@ static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
ar->num_created_vdevs--;
+ arvif->is_created = false;
ath12k_dbg(ab, ATH12K_DBG_MAC, "vdev %pM deleted, vdev_id %d\n",
vif->addr, arvif->vdev_id);
@@ -6613,14 +6671,21 @@ ath12k_mac_op_assign_vif_chanctx(struct ieee80211_hw *hw,
struct ieee80211_bss_conf *link_conf,
struct ieee80211_chanctx_conf *ctx)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
int ret;
struct ath12k_wmi_peer_create_arg param;
- ar = ath12k_ah_to_ar(ah, 0);
+ /* For multi radio wiphy, the vdev was not created during add_interface
+ * create now since we have a channel ctx now to assign to a specific ar/fw
+ */
+ ar = ath12k_mac_assign_vif_to_vdev(hw, vif, ctx);
+ if (!ar) {
+ WARN_ON(1);
+ return -EINVAL;
+ }
+
ab = ar->ab;
mutex_lock(&ar->conf_mutex);
@@ -6696,13 +6761,22 @@ ath12k_mac_op_unassign_vif_chanctx(struct ieee80211_hw *hw,
struct ieee80211_bss_conf *link_conf,
struct ieee80211_chanctx_conf *ctx)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
int ret;
- ar = ath12k_ah_to_ar(ah, 0);
+ /* The vif is expected to be attached to an ar's VDEV.
+ * We leave the vif/vdev in this function as is
+ * and not delete the vdev symmetric to assign_vif_chanctx()
+ * the VDEV will be deleted and unassigned either during
+ * remove_interface() or when there is a change in channel
+ * that moves the vif to a new ar
+ */
+ if (!arvif->is_created)
+ return;
+
+ ar = arvif->ar;
ab = ar->ab;
mutex_lock(&ar->conf_mutex);
@@ -6752,13 +6826,20 @@ ath12k_mac_op_switch_vif_chanctx(struct ieee80211_hw *hw,
int n_vifs,
enum ieee80211_chanctx_switch_mode mode)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_ctx(hw, vifs->old_ctx);
+ if (!ar)
+ return -EINVAL;
mutex_lock(&ar->conf_mutex);
+ /* Switching channels across radio is not allowed */
+ if (ar != ath12k_get_ar_by_ctx(hw, vifs->new_ctx)) {
+ mutex_unlock(&ar->conf_mutex);
+ return -EINVAL;
+ }
+
ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
"mac chanctx switch n_vifs %d mode %d\n",
n_vifs, mode);
--
2.25.1
From: Sriram R <[email protected]>
For ops which passes the vif info, fetch the radio(ar)
to be used for corresponding functions based on the
the vdev creation status. If the vdev is not created yet,
which could happen when the ops are called before channel
is assigned for the vif, the data needs to be cached and this
is done in followup changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 78 +++++++++++++++++++++++----
1 file changed, 67 insertions(+), 11 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index e576c2447a85..f8e6ac1c4a68 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -646,6 +646,24 @@ static struct ath12k *ath12k_get_ar_by_ctx(struct ieee80211_hw *hw,
return ath12k_mac_get_ar_by_chan(hw, ctx->def.chan);
}
+static struct ath12k *ath12k_get_ar_by_vif(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif)
+{
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
+
+ /* If there is one pdev within ah, then we return
+ * ar directly.
+ */
+ if (ah->num_radio == 1)
+ return ah->radio;
+
+ if (arvif->is_created)
+ return arvif->ar;
+
+ return NULL;
+}
+
static void ath12k_pdev_caps_update(struct ath12k *ar)
{
struct ath12k_base *ab = ar->ab;
@@ -2828,11 +2846,17 @@ static void ath12k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_bss_conf *info,
u64 changed)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_vif(hw, vif);
+
+ /* TODO if the vdev is not created on a certain radio,
+ * cache the info to be updated later on vdev creation
+ */
+
+ if (!ar)
+ return;
mutex_lock(&ar->conf_mutex);
@@ -3330,7 +3354,6 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
struct ieee80211_vif *vif, struct ieee80211_sta *sta,
struct ieee80211_key_conf *key)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_base *ab;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
@@ -3347,7 +3370,11 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256)
return 1;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar) {
+ WARN_ON_ONCE(1);
+ return -EINVAL;
+ }
ab = ar->ab;
if (test_bit(ATH12K_FLAG_HW_CRYPTO_DISABLED, &ar->ab->dev_flags))
@@ -3925,7 +3952,6 @@ static int ath12k_mac_op_sta_state(struct ieee80211_hw *hw,
enum ieee80211_sta_state old_state,
enum ieee80211_sta_state new_state)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_sta *arsta = ath12k_sta_to_arsta(sta);
@@ -3937,7 +3963,11 @@ static int ath12k_mac_op_sta_state(struct ieee80211_hw *hw,
new_state == IEEE80211_STA_NOTEXIST))
cancel_work_sync(&arsta->update_wk);
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar) {
+ WARN_ON_ONCE(1);
+ return -EINVAL;
+ }
mutex_lock(&ar->conf_mutex);
@@ -4081,14 +4111,17 @@ static void ath12k_mac_op_sta_rc_update(struct ieee80211_hw *hw,
struct ieee80211_sta *sta,
u32 changed)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_sta *arsta = ath12k_sta_to_arsta(sta);
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct ath12k_peer *peer;
u32 bw, smps;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar) {
+ WARN_ON_ONCE(1);
+ return;
+ }
spin_lock_bh(&ar->ab->base_lock);
@@ -4264,12 +4297,15 @@ static int ath12k_mac_op_conf_tx(struct ieee80211_hw *hw,
unsigned int link_id, u16 ac,
const struct ieee80211_tx_queue_params *params)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
int ret;
- ar = ath12k_ah_to_ar(ah, 0);
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar) {
+ /* TODO cache the info and apply after vdev is created */
+ return -EINVAL;
+ }
mutex_lock(&ar->conf_mutex);
ret = ath12k_mac_conf_tx(arvif, link_id, ac, params);
@@ -6279,6 +6315,10 @@ static int ath12k_mac_op_ampdu_action(struct ieee80211_hw *hw,
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
int ret = -EINVAL;
+ ar = ath12k_get_ar_by_vif(hw, vif);
+ if (!ar)
+ return -EINVAL;
+
ar = ath12k_ah_to_ar(ah, 0);
mutex_lock(&ar->conf_mutex);
@@ -7069,11 +7109,27 @@ static void ath12k_mac_op_flush(struct ieee80211_hw *hw, struct ieee80211_vif *v
u32 queues, bool drop)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
- struct ath12k *ar = ath12k_ah_to_ar(ah, 0);
+ struct ath12k *ar;
+ int i;
if (drop)
return;
+ /* vif can be NULL when flush() is considered for hw */
+ if (!vif) {
+ ar = ath12k_ah_to_ar(ah, 0);
+ for (i = 0; i < ah->num_radio; i++) {
+ ath12k_mac_flush(ar);
+ ar++;
+ }
+ return;
+ }
+
+ ar = ath12k_get_ar_by_vif(hw, vif);
+
+ if (!ar)
+ return;
+
ath12k_mac_flush(ar);
}
--
2.25.1
From: Sriram R <[email protected]>
When multiple radios are advertised as a single wiphy which
supports various bands, a default scan request to mac80211
from cfg80211 will split the driver request based on band,
so each request will have channels belonging to the same band.
With this supported by default, the ath12k driver on receiving
this request checks for one of the channels in the request and
selects the corresponding radio(ar) on which the scan is going
to be performed and creates a vdev on that radio.
Note that on scan completion this vdev is not deleted. If a new
scan request is seen on that same vif for a different band the
vdev will be deleted and created on the new radio supporting the
request. The vdev delete logic is refactored to have this done
dynamically.
The reason for not deleting the vdev on scan stop is to avoid
repeated delete-create sequence if the scan is on the same band.
Also, during channel assign, new vdev creation can be optimized
as well.
Also if the scan is requested when the vdev is in started state,
no switching to new radio is allowed and scan on channels only
within same radio is allowed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <[email protected]>
Signed-off-by: Rameshkumar Sundaram <[email protected]>
---
drivers/net/wireless/ath/ath12k/mac.c | 213 +++++++++++++++++++++-----
1 file changed, 178 insertions(+), 35 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index b723226c7577..e576c2447a85 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -244,6 +244,8 @@ static const u32 ath12k_smps_map[] = {
static int ath12k_start_vdev_delay(struct ath12k *ar,
struct ath12k_vif *arvif);
static void ath12k_mac_stop(struct ath12k *ar);
+static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif);
+static int ath12k_mac_vdev_delete(struct ath12k *ar, struct ieee80211_vif *vif);
static const char *ath12k_mac_phymode_str(enum wmi_phy_mode mode)
{
@@ -2839,6 +2841,45 @@ static void ath12k_mac_op_bss_info_changed(struct ieee80211_hw *hw,
mutex_unlock(&ar->conf_mutex);
}
+static struct ath12k*
+ath12k_mac_select_scan_device(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_scan_request *req)
+{
+ struct ath12k_hw *ah = hw->priv;
+ enum nl80211_band band;
+ struct ath12k *ar;
+ int i;
+
+ if (ah->num_radio == 1)
+ return ah->radio;
+
+ /* Currently mac80211 supports splitting scan requests into
+ * multiple scan requests per band.
+ * Loop through first channel and determine the scan radio
+ * TODO: There could be 5 GHz low/high channels in that case
+ * split the hw request and perform multiple scans
+ */
+
+ if (req->req.channels[0]->center_freq < ATH12K_MIN_5G_FREQ)
+ band = NL80211_BAND_2GHZ;
+ else if (req->req.channels[0]->center_freq < ATH12K_MIN_6G_FREQ)
+ band = NL80211_BAND_5GHZ;
+ else
+ band = NL80211_BAND_6GHZ;
+
+ ar = ah->radio;
+
+ for (i = 0; i < ah->num_radio; i++) {
+ /* TODO 5 GHz low high split changes */
+ if (ar->mac.sbands[band].channels)
+ return ar;
+ ar++;
+ }
+
+ return NULL;
+}
+
void __ath12k_mac_scan_finish(struct ath12k *ar)
{
struct ieee80211_hw *hw = ath12k_ar_to_hw(ar);
@@ -3008,15 +3049,68 @@ static int ath12k_mac_op_hw_scan(struct ieee80211_hw *hw,
struct ieee80211_scan_request *hw_req)
{
struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
- struct ath12k *ar;
+ struct ath12k *ar, *prev_ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
struct cfg80211_scan_request *req = &hw_req->req;
struct ath12k_wmi_scan_req_arg arg = {};
int ret;
int i;
+ bool create = true;
- ar = ath12k_ah_to_ar(ah, 0);
+ if (ah->num_radio == 1) {
+ WARN_ON(!arvif->is_created);
+ ar = ath12k_ah_to_ar(ah, 0);
+ goto scan;
+ }
+
+ /* Since the targeted scan device could depend on the frequency
+ * requested in the hw_req, select the corresponding radio
+ */
+ ar = ath12k_mac_select_scan_device(hw, vif, hw_req);
+ if (!ar)
+ return -EINVAL;
+ /* If the vif is already assigned to a specific vdev of an ar,
+ * check whether its already started, vdev which is started
+ * are not allowed to switch to a new radio.
+ * If the vdev is not started, but was earlier created on a
+ * different ar, delete that vdev and create a new one. We don't
+ * delete at the scan stop as an optimization to avoid reduntant
+ * delete-create vdev's for the same ar, in case the request is
+ * always on the same band for the vif
+ */
+ if (arvif->is_created) {
+ if (WARN_ON(!arvif->ar))
+ return -EINVAL;
+
+ if (ar != arvif->ar && arvif->is_started)
+ return -EINVAL;
+
+ if (ar != arvif->ar) {
+ /* backup the previously used ar ptr, since the vdev delete
+ * would assign the arvif->ar to NULL after the call
+ */
+ prev_ar = arvif->ar;
+ mutex_lock(&prev_ar->conf_mutex);
+ ret = ath12k_mac_vdev_delete(prev_ar, vif);
+ mutex_unlock(&prev_ar->conf_mutex);
+ if (ret)
+ ath12k_warn(prev_ar->ab,
+ "unable to delete scan vdev %d\n", ret);
+ } else {
+ create = false;
+ }
+ }
+ if (create) {
+ mutex_lock(&ar->conf_mutex);
+ ret = ath12k_mac_vdev_create(ar, vif);
+ mutex_unlock(&ar->conf_mutex);
+ if (ret) {
+ ath12k_warn(ar->ab, "unable to create scan vdev %d\n", ret);
+ return -EINVAL;
+ }
+ }
+scan:
mutex_lock(&ar->conf_mutex);
spin_lock_bh(&ar->data_lock);
@@ -3102,10 +3196,13 @@ static int ath12k_mac_op_hw_scan(struct ieee80211_hw *hw,
static void ath12k_mac_op_cancel_hw_scan(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
- struct ath12k_hw *ah = ath12k_hw_to_ah(hw);
struct ath12k *ar;
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
- ar = ath12k_ah_to_ar(ah, 0);
+ if (!arvif->is_created)
+ return;
+
+ ar = arvif->ar;
mutex_lock(&ar->conf_mutex);
ath12k_scan_abort(ar);
@@ -5768,6 +5865,7 @@ static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
if (vif->type != NL80211_IFTYPE_MONITOR && ar->monitor_conf_enabled)
ath12k_mac_monitor_vdev_create(ar);
+ arvif->ar = ar;
return ret;
err_peer_del:
@@ -5794,6 +5892,7 @@ static int ath12k_mac_vdev_create(struct ath12k *ar, struct ieee80211_vif *vif)
ath12k_wmi_vdev_delete(ar, arvif->vdev_id);
ar->num_created_vdevs--;
arvif->is_created = false;
+ arvif->ar = NULL;
ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
ab->free_vdev_map |= 1LL << arvif->vdev_id;
ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
@@ -5811,14 +5910,46 @@ static struct ath12k *ath12k_mac_assign_vif_to_vdev(struct ieee80211_hw *hw,
struct ieee80211_chanctx_conf *ctx)
{
struct ath12k_hw *ah = hw->priv;
- struct ath12k *ar;
+ struct ath12k *ar, *prev_ar;
struct ath12k_base *ab;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
u8 bit;
int ret;
if (arvif->ar) {
- WARN_ON(!arvif->is_created);
+ /* This is not expected really */
+ if (WARN_ON(!arvif->is_created)) {
+ arvif->ar = NULL;
+ return NULL;
+ }
+
+ if (ah->num_radio == 1)
+ goto out;
+
+ ar = ath12k_get_ar_by_ctx(hw, ctx);
+ /* This can happen as scan vdev gets created during multiple scans
+ * across different radios before a vdev is brought up in
+ * a certain radio
+ */
+ if (ar != arvif->ar) {
+ if (WARN_ON(arvif->is_started))
+ return NULL;
+
+ /* backup the previously used ar ptr since arvif->ar would
+ * be set to NULL after vdev delete is done
+ */
+ prev_ar = arvif->ar;
+ mutex_lock(&prev_ar->conf_mutex);
+ ret = ath12k_mac_vdev_delete(prev_ar, vif);
+
+ if (ret)
+ ath12k_warn(prev_ar->ab, "unable to delete vdev %d\n", ret);
+ mutex_unlock(&prev_ar->conf_mutex);
+ ret = ath12k_mac_vdev_create(ar, vif);
+ if (ret)
+ ath12k_warn(ar->ab, "unable to create vdev %d\n", ret);
+ mutex_unlock(&ar->conf_mutex);
+ }
goto out;
}
@@ -5927,38 +6058,19 @@ static void ath12k_mac_vif_unref(struct ath12k_dp *dp, struct ieee80211_vif *vif
}
}
-static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
- struct ieee80211_vif *vif)
+static int ath12k_mac_vdev_delete(struct ath12k *ar, struct ieee80211_vif *vif)
{
- struct ath12k *ar;
struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
- struct ath12k_base *ab;
+ struct ath12k_base *ab = ar->ab;
unsigned long time_left;
int ret;
- if (!arvif->is_created)
- return;
-
- ar = arvif->ar;
- ab = ar->ab;
-
- mutex_lock(&ar->conf_mutex);
-
- ath12k_dbg(ab, ATH12K_DBG_MAC, "mac remove interface (vdev %d)\n",
- arvif->vdev_id);
-
- if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
- ret = ath12k_peer_delete(ar, arvif->vdev_id, vif->addr);
- if (ret)
- ath12k_warn(ab, "failed to submit AP self-peer removal on vdev %d: %d\n",
- arvif->vdev_id, ret);
- }
-
+ lockdep_assert_held(&ar->conf_mutex);
reinit_completion(&ar->vdev_delete_done);
ret = ath12k_wmi_vdev_delete(ar, arvif->vdev_id);
if (ret) {
- ath12k_warn(ab, "failed to delete WMI vdev %d: %d\n",
+ ath12k_warn(ab, "failed to delete WMI scan vdev %d: %d\n",
arvif->vdev_id, ret);
goto err_vdev_del;
}
@@ -5970,6 +6082,10 @@ static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
goto err_vdev_del;
}
+ ab->free_vdev_map |= 1LL << arvif->vdev_id;
+ ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
+ ar->num_created_vdevs--;
+
if (arvif->vdev_type == WMI_VDEV_TYPE_MONITOR) {
ar->monitor_vdev_id = -1;
ar->monitor_vdev_created = false;
@@ -5977,12 +6093,6 @@ static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
ret = ath12k_mac_monitor_vdev_delete(ar);
}
- ab->free_vdev_map |= 1LL << (arvif->vdev_id);
- ar->allocated_vdev_map &= ~(1LL << arvif->vdev_id);
- ab->free_vdev_stats_id_map &= ~(1LL << arvif->vdev_stats_id);
- ar->num_created_vdevs--;
- arvif->is_created = false;
-
ath12k_dbg(ab, ATH12K_DBG_MAC, "vdev %pM deleted, vdev_id %d\n",
vif->addr, arvif->vdev_id);
@@ -6004,6 +6114,39 @@ static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
clear_bit(ATH12K_FLAG_MONITOR_ENABLED, &ar->monitor_flags);
/* TODO: recal traffic pause state based on the available vdevs */
+ arvif->is_created = false;
+ arvif->ar = NULL;
+
+ return ret;
+}
+
+static void ath12k_mac_op_remove_interface(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif)
+{
+ struct ath12k *ar;
+ struct ath12k_vif *arvif = ath12k_vif_to_arvif(vif);
+ struct ath12k_base *ab;
+ int ret;
+
+ if (!arvif->is_created)
+ return;
+
+ ar = arvif->ar;
+ ab = ar->ab;
+
+ mutex_lock(&ar->conf_mutex);
+
+ ath12k_dbg(ab, ATH12K_DBG_MAC, "mac remove interface (vdev %d)\n",
+ arvif->vdev_id);
+
+ if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
+ ret = ath12k_peer_delete(ar, arvif->vdev_id, vif->addr);
+ if (ret)
+ ath12k_warn(ab, "failed to submit AP self-peer removal on vdev %d: %d\n",
+ arvif->vdev_id, ret);
+ }
+
+ ath12k_mac_vdev_delete(ar, vif);
mutex_unlock(&ar->conf_mutex);
}
--
2.25.1
Rameshkumar Sundaram <[email protected]> writes:
> From: Sriram R <[email protected]>
>
> When mac80211 does drv start/stop, apply the state change
> for all the radios within the wiphy in ath12k.
>
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
>
> Signed-off-by: Sriram R <[email protected]>
> Signed-off-by: Rameshkumar Sundaram <[email protected]>
I haven't reviewed the patchset fully yet, first quick impressions:
> +static void ath12k_drain_tx(struct ath12k_hw *ah)
> +{
> + int i;
> + struct ath12k *ar;
We usually try to have reverse xmas style, of course not always possible
but here it is.
> + ar = ah->radio;
> +
> + for (i = 0; i < ah->num_radio; i++) {
> + ath12k_mac_drain_tx(ar);
> + ar++;
> + }
> +}
Please avoid pointer arithmetic (in this case 'ar++') as much as
possible, it's just so easy to shoot yourself in the foot. In patch 1
you add ath12k_ah_to_ar(), why not use it?
And I see this pattern quite a lot, should we have
ath12k_for_each_radio() or something like that? Or did I see that macro
in some patch already?
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
On 2/16/2024 8:35 AM, Kalle Valo wrote:
> Rameshkumar Sundaram <[email protected]> writes:
>
>> From: Sriram R <[email protected]>
>>
>> When mac80211 does drv start/stop, apply the state change
>> for all the radios within the wiphy in ath12k.
>>
>> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
>> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
>>
>> Signed-off-by: Sriram R <[email protected]>
>> Signed-off-by: Rameshkumar Sundaram <[email protected]>
>
> I haven't reviewed the patchset fully yet, first quick impressions:
I didn't review it at all since it has a dependency upon a series that
needs rework, and hence I figure this series will require rework.
Jeff Johnson <[email protected]> writes:
> On 2/16/2024 8:35 AM, Kalle Valo wrote:
>> Rameshkumar Sundaram <[email protected]> writes:
>>
>>> From: Sriram R <[email protected]>
>>>
>>> When mac80211 does drv start/stop, apply the state change
>>> for all the radios within the wiphy in ath12k.
>>>
>>> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
>>> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
>>>
>>> Signed-off-by: Sriram R <[email protected]>
>>> Signed-off-by: Rameshkumar Sundaram <[email protected]>
>>
>> I haven't reviewed the patchset fully yet, first quick impressions:
>
> I didn't review it at all since it has a dependency upon a series that
> needs rework, and hence I figure this series will require rework.
Makes sense, I'll then mark this as Changes Requested in patchwork.
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
> -----Original Message-----
> From: Kalle Valo <[email protected]>
> Sent: Friday, February 16, 2024 10:06 PM
> To: Rameshkumar Sundaram (QUIC) <[email protected]>
> Cc: [email protected]; [email protected]; Sriram
> R <[email protected]>
> Subject: Re: [PATCH v2 03/12] wifi: ath12k: modify ath12k mac
> start/stop ops for single wiphy
>
> Rameshkumar Sundaram <[email protected]> writes:
>
> > From: Sriram R <[email protected]>
> >
> > When mac80211 does drv start/stop, apply the state change for all
> the
> > radios within the wiphy in ath12k.
> >
> > Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-
> QCAHKSWPL_SILICONZ-1
> > Tested-on: WCN7850 hw2.0 PCI
> > WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> >
> > Signed-off-by: Sriram R <[email protected]>
> > Signed-off-by: Rameshkumar Sundaram <[email protected]>
>
> I haven't reviewed the patchset fully yet, first quick impressions:
>
> > +static void ath12k_drain_tx(struct ath12k_hw *ah) {
> > + int i;
> > + struct ath12k *ar;
>
> We usually try to have reverse xmas style, of course not always possible
> but here it is.
>
Sure, Will fix it v3.
> > + ar = ah->radio;
> > +
> > + for (i = 0; i < ah->num_radio; i++) {
> > + ath12k_mac_drain_tx(ar);
> > + ar++;
> > + }
> > +}
>
> Please avoid pointer arithmetic (in this case 'ar++') as much as possible,
> it's just so easy to shoot yourself in the foot. In patch 1 you add
> ath12k_ah_to_ar(), why not use it?
Sure, will avoid this and take reference from ah->radio[]
>
> And I see this pattern quite a lot, should we have
> ath12k_for_each_radio() or something like that? Or did I see that macro
> in some patch already?
Sure, makes sense, guess it was in v1 of patch [01/12] in this series, but was removed and used inline in subsequent patch sets.
will introduced it back.
>
> --
> https://patchwork.kernel.org/project/linux-wireless/list/
>
> https://wireless.wiki.kernel.org/en/developers/documentation/submitti
> ngpatches