Currently we force enable power save on non-running vdevs, this results
in unexpected ping latency in below scenarios:
1. disable power save from userspace.
2. trigger suspend/resume.
With step 1 power save is disabled successfully and we get a good latency:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=5.13 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.45 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=5.99 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=6.34 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=4.47 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=6.45 ms
While after step 2, the latency becomes much larger:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=17.7 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=15.0 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=14.3 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=16.5 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=20.1 ms
The reason is, with step 2, power save is force enabled due to vdev not
running, although mac80211 was trying to disable it to honor userspace
configuration:
ath11k_pci 0000:03:00.0: wmi cmd sta powersave mode psmode 1 vdev id 0
Call Trace:
ath11k_wmi_pdev_set_ps_mode
ath11k_mac_op_bss_info_changed
ieee80211_bss_info_change_notify
ieee80211_reconfig
ieee80211_resume
wiphy_resume
This logic is taken from ath10k where it was added due to below comment:
Firmware doesn't behave nicely and consumes more power than
necessary if PS is disabled on a non-started vdev.
However we don't know whether such an issue also occurs to ath11k firmware
or not. But even if it does, it's not appropriate because it goes against
userspace, even cfg/mac80211 don't know we have enabled it in fact.
Remove it to fix this issue. In this way we not only get a better latency,
but also, and the most important, keeps the consistency between userspace
and kernel/driver. The biggest price for that would be the power consumption,
which is not that important, compared with the consistency.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: b2beffa7d9a6 ("ath11k: enable 802.11 power save mode in station mode")
Signed-off-by: Baochen Qiang <[email protected]>
---
drivers/net/wireless/ath/ath11k/mac.c | 9 +--------
1 file changed, 1 insertion(+), 8 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index a6a37d67a50a..42a6a51a6a9d 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -1231,14 +1231,7 @@ static int ath11k_mac_vif_setup_ps(struct ath11k_vif *arvif)
enable_ps = arvif->ps;
- if (!arvif->is_started) {
- /* mac80211 can update vif powersave state while disconnected.
- * Firmware doesn't behave nicely and consumes more power than
- * necessary if PS is disabled on a non-started vdev. Hence
- * force-enable PS for non-running vdevs.
- */
- psmode = WMI_STA_PS_MODE_ENABLED;
- } else if (enable_ps) {
+ if (enable_ps) {
psmode = WMI_STA_PS_MODE_ENABLED;
param = WMI_STA_PS_PARAM_INACTIVITY_TIME;
base-commit: 7a5ed5a3801e9b6cf7bafbb0a05c70cef620b22a
--
2.25.1
On 3/9/2024 3:31 AM, Baochen Qiang wrote:
> Currently we force enable power save on non-running vdevs, this results
> in unexpected ping latency in below scenarios:
> 1. disable power save from userspace.
> 2. trigger suspend/resume.
>
> With step 1 power save is disabled successfully and we get a good latency:
>
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=5.13 ms
> 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.45 ms
> 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=5.99 ms
> 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=6.34 ms
> 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=4.47 ms
> 64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=6.45 ms
>
> While after step 2, the latency becomes much larger:
>
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=17.7 ms
> 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=15.0 ms
> 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=14.3 ms
> 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=16.5 ms
> 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=20.1 ms
>
> The reason is, with step 2, power save is force enabled due to vdev not
> running, although mac80211 was trying to disable it to honor userspace
> configuration:
>
> ath11k_pci 0000:03:00.0: wmi cmd sta powersave mode psmode 1 vdev id 0
> Call Trace:
> ath11k_wmi_pdev_set_ps_mode
> ath11k_mac_op_bss_info_changed
> ieee80211_bss_info_change_notify
> ieee80211_reconfig
> ieee80211_resume
> wiphy_resume
>
> This logic is taken from ath10k where it was added due to below comment:
>
> Firmware doesn't behave nicely and consumes more power than
> necessary if PS is disabled on a non-started vdev.
>
> However we don't know whether such an issue also occurs to ath11k firmware
> or not. But even if it does, it's not appropriate because it goes against
> userspace, even cfg/mac80211 don't know we have enabled it in fact.
>
> Remove it to fix this issue. In this way we not only get a better latency,
> but also, and the most important, keeps the consistency between userspace
> and kernel/driver. The biggest price for that would be the power consumption,
> which is not that important, compared with the consistency.
>
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
>
> Fixes: b2beffa7d9a6 ("ath11k: enable 802.11 power save mode in station mode")
> Signed-off-by: Baochen Qiang <[email protected]>
Acked-by: Jeff Johnson <[email protected]>
Baochen Qiang <[email protected]> wrote:
> Currently we force enable power save on non-running vdevs, this results
> in unexpected ping latency in below scenarios:
> 1. disable power save from userspace.
> 2. trigger suspend/resume.
>
> With step 1 power save is disabled successfully and we get a good latency:
>
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=5.13 ms
> 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.45 ms
> 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=5.99 ms
> 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=6.34 ms
> 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=4.47 ms
> 64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=6.45 ms
>
> While after step 2, the latency becomes much larger:
>
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=17.7 ms
> 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=15.0 ms
> 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=14.3 ms
> 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=16.5 ms
> 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=20.1 ms
>
> The reason is, with step 2, power save is force enabled due to vdev not
> running, although mac80211 was trying to disable it to honor userspace
> configuration:
>
> ath11k_pci 0000:03:00.0: wmi cmd sta powersave mode psmode 1 vdev id 0
> Call Trace:
> ath11k_wmi_pdev_set_ps_mode
> ath11k_mac_op_bss_info_changed
> ieee80211_bss_info_change_notify
> ieee80211_reconfig
> ieee80211_resume
> wiphy_resume
>
> This logic is taken from ath10k where it was added due to below comment:
>
> Firmware doesn't behave nicely and consumes more power than
> necessary if PS is disabled on a non-started vdev.
>
> However we don't know whether such an issue also occurs to ath11k firmware
> or not. But even if it does, it's not appropriate because it goes against
> userspace, even cfg/mac80211 don't know we have enabled it in fact.
>
> Remove it to fix this issue. In this way we not only get a better latency,
> but also, and the most important, keeps the consistency between userspace
> and kernel/driver. The biggest price for that would be the power consumption,
> which is not that important, compared with the consistency.
>
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
>
> Fixes: b2beffa7d9a6 ("ath11k: enable 802.11 power save mode in station mode")
> Signed-off-by: Baochen Qiang <[email protected]>
> Signed-off-by: Kalle Valo <[email protected]>
Patch applied to ath-next branch of ath.git, thanks.
01296b39d351 wifi: ath11k: don't force enable power save on non-running vdevs
--
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches