Hallo,
I recently bought an Asus USB-N53 Dual Band Wireless Network Adapter and
noticed that I have to enable CONFIG_RT2800USB_UNKNOWN to get it working. With
this option enabled everything is working fine as far as I have tested.
So I'd line to get things right and move this device out of
CONFIG_RT2800USB_UNKNOWN to where it belongs.
Here is the information I have about this device, feel tree to ask if you need
anything addition.
Asus Website about the device:
http://www.asus.com/Networks/Wireless_Adapters/USBN53/
output of lsusb:
Bus 005 Device 013: ID 0b05:179d ASUSTek Computer, Inc. USB-N53 802.11abgn
Network Adapter [Ralink RT3572]
output of dmesg:
usb 5-6: new high-speed USB device number 13 using ehci_hcd
usb 5-6: New USB device found, idVendor=0b05, idProduct=179d
usb 5-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-6: Product: 802.11 n WLAN
usb 5-6: Manufacturer: Ralink
usb 5-6: SerialNumber: 1.0
usb 5-6: reset high-speed USB device number 13 using ehci_hcd
ieee80211 phy6: Selected rate control algorithm 'minstrel_ht'
Registered led device: rt2800usb-phy6::radio
Registered led device: rt2800usb-phy6::assoc
Registered led device: rt2800usb-phy6::quality
So according to lsusb this is a RT3572 device, which does also match with the
chip description from ralink:
http://www.ralinktech.com/en/02_products/product.php?sn=1009
I suggest moving the device to the CONFIG_RT2800USB_RT35XX section in
rt2800usb.c, see attached patch.
diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c
index 6cf3365..6681bfc 100644
--- a/drivers/net/wireless/rt2x00/rt2800usb.c
+++ b/drivers/net/wireless/rt2x00/rt2800usb.c
@@ -1157,6 +1157,8 @@ static struct usb_device_id rt2800usb_device_table[] = {
{ USB_DEVICE(0x1690, 0x0744) },
{ USB_DEVICE(0x1690, 0x0761) },
{ USB_DEVICE(0x1690, 0x0764) },
+ /* ASUS */
+ { USB_DEVICE(0x0b05, 0x179d) },
/* Cisco */
{ USB_DEVICE(0x167b, 0x4001) },
/* EnGenius */
@@ -1222,7 +1224,6 @@ static struct usb_device_id rt2800usb_device_table[] = {
{ USB_DEVICE(0x0b05, 0x1760) },
{ USB_DEVICE(0x0b05, 0x1761) },
{ USB_DEVICE(0x0b05, 0x1790) },
- { USB_DEVICE(0x0b05, 0x179d) },
/* AzureWave */
{ USB_DEVICE(0x13d3, 0x3262) },
{ USB_DEVICE(0x13d3, 0x3284) },
Greeting,
Maxi
Hi Maxi,
On 08/26/12 15:33, Maximilian Engelhardt wrote:
> Hallo,
>
> I recently bought an Asus USB-N53 Dual Band Wireless Network Adapter and
> noticed that I have to enable CONFIG_RT2800USB_UNKNOWN to get it working. With
> this option enabled everything is working fine as far as I have tested.
>
> So I'd line to get things right and move this device out of
> CONFIG_RT2800USB_UNKNOWN to where it belongs.
>
Thanks for identifying the adapter. Moving it out of
CONFIG_RT2800USB_UNKNOWN is definitely the way to go.
>
> Here is the information I have about this device, feel tree to ask if you need
> anything addition.
>
> Asus Website about the device:
> http://www.asus.com/Networks/Wireless_Adapters/USBN53/
>
> output of lsusb:
> Bus 005 Device 013: ID 0b05:179d ASUSTek Computer, Inc. USB-N53 802.11abgn
> Network Adapter [Ralink RT3572]
>
> output of dmesg:
> usb 5-6: new high-speed USB device number 13 using ehci_hcd
> usb 5-6: New USB device found, idVendor=0b05, idProduct=179d
> usb 5-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> usb 5-6: Product: 802.11 n WLAN
> usb 5-6: Manufacturer: Ralink
> usb 5-6: SerialNumber: 1.0
> usb 5-6: reset high-speed USB device number 13 using ehci_hcd
> ieee80211 phy6: Selected rate control algorithm 'minstrel_ht'
> Registered led device: rt2800usb-phy6::radio
> Registered led device: rt2800usb-phy6::assoc
> Registered led device: rt2800usb-phy6::quality
>
>
> So according to lsusb this is a RT3572 device, which does also match with the
> chip description from ralink:
> http://www.ralinktech.com/en/02_products/product.php?sn=1009
>
> I suggest moving the device to the CONFIG_RT2800USB_RT35XX section in
> rt2800usb.c, see attached patch.
>
We need a proper Signed-off-by line from you in accordance with the
patch submission procedures. I can pick up your patch, add your
Signed-off-by, and submit it for inclusion upstream, but you have to
confirm that you are OK with me adding your Signed-off-by to the patch.
>
> diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c
> index 6cf3365..6681bfc 100644
> --- a/drivers/net/wireless/rt2x00/rt2800usb.c
> +++ b/drivers/net/wireless/rt2x00/rt2800usb.c
> @@ -1157,6 +1157,8 @@ static struct usb_device_id rt2800usb_device_table[] = {
> { USB_DEVICE(0x1690, 0x0744) },
> { USB_DEVICE(0x1690, 0x0761) },
> { USB_DEVICE(0x1690, 0x0764) },
> + /* ASUS */
> + { USB_DEVICE(0x0b05, 0x179d) },
> /* Cisco */
> { USB_DEVICE(0x167b, 0x4001) },
> /* EnGenius */
> @@ -1222,7 +1224,6 @@ static struct usb_device_id rt2800usb_device_table[] = {
> { USB_DEVICE(0x0b05, 0x1760) },
> { USB_DEVICE(0x0b05, 0x1761) },
> { USB_DEVICE(0x0b05, 0x1790) },
> - { USB_DEVICE(0x0b05, 0x179d) },
> /* AzureWave */
> { USB_DEVICE(0x13d3, 0x3262) },
> { USB_DEVICE(0x13d3, 0x3284) },
>
---
Gertjan
Hi Gertjan,
On Sunday 26 August 2012 21:21:05 Gertjan van Wingerde wrote:
> Hi Maxi,
>
> On 08/26/12 15:33, Maximilian Engelhardt wrote:
> > Hallo,
> >
> > I recently bought an Asus USB-N53 Dual Band Wireless Network Adapter and
> > noticed that I have to enable CONFIG_RT2800USB_UNKNOWN to get it working.
> > With this option enabled everything is working fine as far as I have
> > tested.
> >
> > So I'd line to get things right and move this device out of
> > CONFIG_RT2800USB_UNKNOWN to where it belongs.
>
> Thanks for identifying the adapter. Moving it out of
> CONFIG_RT2800USB_UNKNOWN is definitely the way to go.
>
> > Here is the information I have about this device, feel tree to ask if you
> > need anything addition.
> >
> > Asus Website about the device:
> > http://www.asus.com/Networks/Wireless_Adapters/USBN53/
> >
> > output of lsusb:
> > Bus 005 Device 013: ID 0b05:179d ASUSTek Computer, Inc. USB-N53 802.11abgn
> > Network Adapter [Ralink RT3572]
> >
> > output of dmesg:
> > usb 5-6: new high-speed USB device number 13 using ehci_hcd
> > usb 5-6: New USB device found, idVendor=0b05, idProduct=179d
> > usb 5-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> > usb 5-6: Product: 802.11 n WLAN
> > usb 5-6: Manufacturer: Ralink
> > usb 5-6: SerialNumber: 1.0
> > usb 5-6: reset high-speed USB device number 13 using ehci_hcd
> > ieee80211 phy6: Selected rate control algorithm 'minstrel_ht'
> > Registered led device: rt2800usb-phy6::radio
> > Registered led device: rt2800usb-phy6::assoc
> > Registered led device: rt2800usb-phy6::quality
> >
> >
> > So according to lsusb this is a RT3572 device, which does also match with
> > the chip description from ralink:
> > http://www.ralinktech.com/en/02_products/product.php?sn=1009
> >
> > I suggest moving the device to the CONFIG_RT2800USB_RT35XX section in
> > rt2800usb.c, see attached patch.
>
> We need a proper Signed-off-by line from you in accordance with the
> patch submission procedures. I can pick up your patch, add your
> Signed-off-by, and submit it for inclusion upstream, but you have to
> confirm that you are OK with me adding your Signed-off-by to the patch.
Here you go.
Signed-off-by: Maximilian Engelhardt <[email protected]>
> > diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c
> > b/drivers/net/wireless/rt2x00/rt2800usb.c index 6cf3365..6681bfc 100644
> > --- a/drivers/net/wireless/rt2x00/rt2800usb.c
> > +++ b/drivers/net/wireless/rt2x00/rt2800usb.c
> > @@ -1157,6 +1157,8 @@ static struct usb_device_id rt2800usb_device_table[]
> > = {>
> > { USB_DEVICE(0x1690, 0x0744) },
> > { USB_DEVICE(0x1690, 0x0761) },
> > { USB_DEVICE(0x1690, 0x0764) },
> >
> > + /* ASUS */
> > + { USB_DEVICE(0x0b05, 0x179d) },
> >
> > /* Cisco */
> > { USB_DEVICE(0x167b, 0x4001) },
> > /* EnGenius */
> >
> > @@ -1222,7 +1224,6 @@ static struct usb_device_id rt2800usb_device_table[]
> > = {>
> > { USB_DEVICE(0x0b05, 0x1760) },
> > { USB_DEVICE(0x0b05, 0x1761) },
> > { USB_DEVICE(0x0b05, 0x1790) },
> >
> > - { USB_DEVICE(0x0b05, 0x179d) },
> >
> > /* AzureWave */
> > { USB_DEVICE(0x13d3, 0x3262) },
> > { USB_DEVICE(0x13d3, 0x3284) },
>
> ---
> Gertjan
Thanks for your help.