hi,
kernel 3.9.7-100.fc17.x86_64
- dmesg:
usb 2-1.5: new high-speed USB device number 16 using ehci-pci
usb 2-1.5: New USB device found, idVendor=0bda, idProduct=8176
usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1.5: Product: 802.11n WLAN Adapter
usb 2-1.5: Manufacturer: Realtek
usb 2-1.5: SerialNumber: 00e04c000001
rtl8192cu: Chip version 0x10
rtl8192cu: MAC address: 00:e0:4c:07:dd:45
rtl8192cu: Board Type 0
rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
ieee80211 phy11: Selected rate control algorithm 'rtl_rc'
rtlwifi: wireless switch is on
cfg80211: Calling CRDA for country: ES
cfg80211: Regulatory domain changed to country: ES
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
rtl8192cu: MAC auto ON okay!
rtl8192cu: Tx queue select: 0x05
IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
- iw list:
Wiphy phy2
Band 1:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-7, 32
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
RTS threshold: 2347
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* action
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* Unknown command (84)
* Unknown command (87)
* Unknown command (85)
* Unknown command (89)
* Unknown command (92)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
* Unknown mode (10): 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
Supported RX frame types:
* IBSS: 0x0040 0x00b0 0x00c0 0x00d0
* managed: 0x0040 0x00d0
* AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
* AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
* mesh point: 0x00b0 0x00c0 0x00d0
* P2P-client: 0x0040 0x00d0
* P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
* Unknown mode (10): 0x0040 0x00d0
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
thank you.
On 06/23/2013 01:48 AM, Xose Vazquez Perez wrote:
> hi,
>
> kernel 3.9.7-100.fc17.x86_64
>
> - dmesg:
>
> usb 2-1.5: new high-speed USB device number 16 using ehci-pci
> usb 2-1.5: New USB device found, idVendor=0bda, idProduct=8176
> usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> usb 2-1.5: Product: 802.11n WLAN Adapter
> usb 2-1.5: Manufacturer: Realtek
> usb 2-1.5: SerialNumber: 00e04c000001
> rtl8192cu: Chip version 0x10
> rtl8192cu: MAC address: 00:e0:4c:07:dd:45
> rtl8192cu: Board Type 0
> rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
> rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
> ieee80211 phy11: Selected rate control algorithm 'rtl_rc'
> rtlwifi: wireless switch is on
> cfg80211: Calling CRDA for country: ES
> cfg80211: Regulatory domain changed to country: ES
> cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
> cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
> cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
> cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
> cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
> cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
> rtl8192cu: MAC auto ON okay!
> rtl8192cu: Tx queue select: 0x05
> IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
>
>
> - iw list:
>
> Wiphy phy2
> Band 1:
> Capabilities: 0x1862
> HT20/HT40
> Static SM Power Save
> RX HT20 SGI
> RX HT40 SGI
> No RX STBC
> Max AMSDU length: 7935 bytes
> DSSS/CCK HT40
> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
> Minimum RX AMPDU time spacing: 16 usec (0x07)
> HT TX/RX MCS rate indexes supported: 0-7, 32
> Frequencies:
> * 2412 MHz [1] (20.0 dBm)
> * 2417 MHz [2] (20.0 dBm)
> * 2422 MHz [3] (20.0 dBm)
> * 2427 MHz [4] (20.0 dBm)
> * 2432 MHz [5] (20.0 dBm)
> * 2437 MHz [6] (20.0 dBm)
> * 2442 MHz [7] (20.0 dBm)
> * 2447 MHz [8] (20.0 dBm)
> * 2452 MHz [9] (20.0 dBm)
> * 2457 MHz [10] (20.0 dBm)
> * 2462 MHz [11] (20.0 dBm)
> * 2467 MHz [12] (disabled)
> * 2472 MHz [13] (disabled)
> * 2484 MHz [14] (disabled)
> Bitrates (non-HT):
> * 1.0 Mbps
> * 2.0 Mbps
> * 5.5 Mbps
> * 11.0 Mbps
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> max # scan SSIDs: 4
> max scan IEs length: 2257 bytes
> RTS threshold: 2347
> Coverage class: 0 (up to 0m)
> Supported Ciphers:
> * WEP40 (00-0f-ac:1)
> * WEP104 (00-0f-ac:5)
> * TKIP (00-0f-ac:2)
> * CCMP (00-0f-ac:4)
> Available Antennas: TX 0 RX 0
> Supported interface modes:
> * IBSS
> * managed
> * AP
> * AP/VLAN
> * monitor
> software interface modes (can always be added):
> * AP/VLAN
> * monitor
> interface combinations are not supported
> Supported commands:
> * new_interface
> * set_interface
> * new_key
> * new_beacon
> * new_station
> * new_mpath
> * set_mesh_params
> * set_bss
> * authenticate
> * associate
> * deauthenticate
> * disassociate
> * join_ibss
> * join_mesh
> * set_tx_bitrate_mask
> * action
> * frame_wait_cancel
> * set_wiphy_netns
> * set_channel
> * set_wds_peer
> * Unknown command (84)
> * Unknown command (87)
> * Unknown command (85)
> * Unknown command (89)
> * Unknown command (92)
> * connect
> * disconnect
> Supported TX frame types:
> * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> * Unknown mode (10): 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
> Supported RX frame types:
> * IBSS: 0x0040 0x00b0 0x00c0 0x00d0
> * managed: 0x0040 0x00d0
> * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
> * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
> * mesh point: 0x00b0 0x00c0 0x00d0
> * P2P-client: 0x0040 0x00d0
> * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
> * Unknown mode (10): 0x0040 0x00d0
> HT Capability overrides:
> * MCS: ff ff ff ff ff ff ff ff ff ff
> * maximum A-MSDU length
> * supported channel width
> * short GI for 40 MHz
> * max A-MPDU length exponent
> * min MPDU start spacing
> Device supports TX status socket option.
> Device supports HT-IBSS.
>
>
> thank you.
>
It also happens in 3.10.2. This time CC Larry.
thanks.