Hi,
Earlier I had some trouble getting the wl1271 driver to work on an
OMAP3 board (SDIO instability, timeouts). I haven't been able to track
down the exact cause, it appears to have been some muxing issue
(although I had manually verified each and every related pin).
Now I've got it to work using the firmware recently contributed to
linux-firmware by TI, but I've run into another issue. The first time
the interface is brought up everything appears to work fine (a scan
returns APs), but once I bring the interface down any subsequent
attempt to bring the interface back up again fail.
Sysfs indicates that after the interface has been brought down, the
MMC regulator (VSIM) and the WLAN_PMENA GPIO remain enabled. Is this
correct behavior?
Upon the second ifup it seems to first fail waiting for an "init
complete" interrupt (WL1271_ACX_INTR_INIT_COMPLETE).
As for the regulators, I'm still not sure if I've configured them
correctly (especially the consumer structs).
I'm running v2.6.36 with Ohad's patches to allow wl1271 configuration
in the board code and have also applied the runtime PM patchset
(http://www.spinics.net/lists/linux-wireless/msg56664.html).
Relevant code snippets below, as well as the kernel log
Joerie
---------------------------------------------------------------
#define NOWPLUS_WLAN_IRQ_GPIO 21
#define NOWPLUS_WLAN_PMENA_GPIO 160
static struct regulator_consumer_supply nowplus_vsim_supply = {
.supply = "vmmc",
};
static struct regulator_consumer_supply nowplus_wl1271_supply = {
.supply = "vmmc_aux",
.dev_name = "mmci-omap-hs.2",
};
/* VSIM for WiFi SDIO */
static struct regulator_init_data nowplus_vsim = {
.constraints = {
.name = "VSIM",
.min_uV = 1800000,
.max_uV = 1800000,
.apply_uV = true,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &nowplus_vsim_supply,
};
static struct regulator_init_data nowplus_wlgpio = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
.consumer_supplies = &nowplus_wl1271_supply,
};
static struct fixed_voltage_config nowplus_vwlan = {
.supply_name = "vwl1271",
.microvolts = 1800000, /* 1.8V */
.gpio = NOWPLUS_WLAN_PMENA_GPIO,
.startup_delay = 70000, /* 70msec */
.enable_high = 1,
.enabled_at_boot = 0,
.init_data = &nowplus_wlgpio,
};
static struct platform_device nowplus_vwlan_device = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &nowplus_vwlan,
},
};
static int nowplus_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
omap2_hsmmc_init(nowplus_mmc);
/* link regulators to MMC adapters */
nowplus_vmmc1_supply.dev = nowplus_mmc[0].dev;
nowplus_vmmc2_supply.dev = nowplus_mmc[1].dev;
nowplus_vsim_supply.dev = nowplus_mmc[2].dev;
return 0;
}
---------------------------------------------------------------
[ 1.475463] mmc2: card claims to support voltages below the defined
range. These will be ignored.
[ 1.518280] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 1.535400] mmc2: new SDIO card at address 0001
[ 1.540435] PM: Adding info for mmc:mmc2:0001
[ 1.545562] PM: Adding info for sdio:mmc2:0001:1
[ 1.550689] wl1271_sdio mmc2:0001:1: __pm_runtime_resume()!
[ 1.559722] mmc mmc2:0001: __pm_runtime_resume()!
[ 1.564270] mmc mmc2:0001: __pm_runtime_resume() returns 1!
[ 1.573120] wl1271_sdio mmc2:0001:1: __pm_runtime_resume() returns 0!
[ 1.582061] sdio mmc2:0001:1: __pm_runtime_suspend()!
[ 1.586608] sdio mmc2:0001:1: __pm_runtime_suspend() returns 0!
[ 1.595397] PM: Adding info for sdio:mmc2:0001:2
[ 1.600219] wl1271_sdio mmc2:0001:2: __pm_runtime_resume()!
[ 1.609069] mmc mmc2:0001: __pm_runtime_resume()!
[ 1.613464] mmc mmc2:0001: __pm_runtime_resume() returns 1!
[ 1.622375] wl1271_sdio mmc2:0001:2: __pm_runtime_resume() returns 0!
[ 1.632232] PM: Adding info for platform:wl1271
[ 1.637268] PM: Adding info for No Bus:phy0
[ 1.643096] PM: Adding info for No Bus:wlan0
[ 1.648162] wl1271: loaded
[ 1.652587] wl1271: initialized
[ 1.656768] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
[ 1.665130] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
[ 6.197753] Freeing init memory: 136K
[ 6.510559] PM: Adding info for No Bus:vcs2
[ 6.511383] PM: Adding info for No Bus:vcsa2
[ 13.935028] wl1271: mac80211 start
[ 13.935058] wl1271: mac80211 stop
[ 24.939239] usb0: no IPv6 routers present
<wlan0 brought up>
--- wlan0 down ---
[ 161.776367] wl1271: mac80211 configure filter
[ 161.776397] wl1271: waking up chip from elp
[ 161.776702] wl1271: mac80211 configure filter
[ 161.782470] wl1271: IRQ
[ 161.782531] wl1271: wakeup time: 0 ms
[ 161.782531] wl1271: acx group address tbl
[ 161.782562] wl1271: cmd configure
[ 161.783325] wl1271: IRQ work
[ 161.783447] wl1271: intr: 0x20 (fw_rx_counter = 0, drv_rx_counter =
0, tx_results_counter = 0)
[ 161.783477] wl1271: WL1271_ACX_INTR_HW_AVAILABLE
[ 161.783508] wl1271: acx group address tbl
[ 161.783508] wl1271: cmd configure
[ 161.783966] wl1271: mac80211 remove interface
[ 161.783996] wl1271: down
[ 161.784088] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
[ 161.784149] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
[ 161.784179] wl1271: mac80211 stop
[ 161.790985] wl1271: elp work
--- wlan0 up ---
[ 189.104309] wl1271: mac80211 start
[ 189.104339] wl1271: mac80211 add interface type 2 mac a0:07:98:6a:f8:c7
[ 189.134704] wl1271_sdio mmc2:0001:2: __pm_runtime_resume()!
[ 189.134735] mmc mmc2:0001: __pm_runtime_resume()!
[ 189.134765] mmc mmc2:0001: __pm_runtime_resume() returns 1!
[ 189.134796] wl1271_sdio mmc2:0001:2: __pm_runtime_resume() returns 0!
[ 189.345672] wl1271: mem_start 00000000 mem_size 00000000
[ 189.345703] wl1271: reg_start 00300000 reg_size 00008800
[ 189.345703] wl1271: mem2_start 00000000 mem2_size 00000000
[ 189.345733] wl1271: mem3_start 00000000 mem3_size 00000000
[ 189.346252] wl1271: chip id 0x4030111 (1271 PG20)
[ 189.346954] wl1271: pause1 0x40f73
[ 189.347534] wl1271: mem_start 00040000 mem_size 00014FC0
[ 189.347564] wl1271: reg_start 00310000 reg_size 00006000
[ 189.347564] wl1271: mem2_start 00000000 mem2_size 00000000
[ 189.347595] wl1271: mem3_start 00000000 mem3_size 00000000
[ 189.347900] wl1271: DRPW_SCRATCH_START 0031002c
[ 189.347961] wl1271: clk2 0x80316a2c
[ 189.348022] wl1271: mem_start 00040000 mem_size 00014FC0
[ 189.348022] wl1271: reg_start 00300000 reg_size 0000A000
[ 189.348052] wl1271: mem2_start 003004F8 mem2_size 00000004
[ 189.348052] wl1271: mem3_start 00040404 mem3_size 00000000
[ 189.348480] wl1271: soft reset bootdata 0x0
[ 189.348571] wl1271: nvs burst write 0x30546c: 0x986af8c7
[ 189.348632] wl1271: nvs burst write 0x305470: 0xa007
[ 189.348693] wl1271: mem_start 00040000 mem_size 00014FC0
[ 189.348724] wl1271: reg_start 00300000 reg_size 0000A000
[ 189.348724] wl1271: mem2_start 003004F8 mem2_size 00000004
[ 189.348754] wl1271: mem3_start 00040404 mem3_size 00000000
[ 189.349121] wl1271: ACX_EEPROMLESS_IND_REG
[ 189.349212] wl1271: chip id 0x4030111
[ 189.349548] wl1271: firmware chunks to be uploaded: 6
[ 189.349578] wl1271: chunk 5 addr 0x0 len 195924
[ 189.349609] wl1271: starting firmware upload
[ 189.349609] wl1271: fw_data_len 195924 chunk_size 512
[ 189.349639] wl1271: mem_start 00000000 mem_size 000177C0
[ 189.349639] wl1271: reg_start 00300000 reg_size 00008800
[ 189.349670] wl1271: mem2_start 00000000 mem2_size 00000000
[ 189.349670] wl1271: mem3_start 00000000 mem3_size 00000000
[ 189.349975] wl1271: uploading fw chunk 0xd085900c to 0x0
<...>
[ 191.986022] wl1271: uploading fw last chunk (176 B) 0xd089b4b0 to 0x316e00
[ 191.986297] wl1271: chip id after firmware boot: 0x4030111
[ 194.105377] wl1271: ERROR timeout waiting for the hardware to
complete initialization
<...>
[ 194.485961] wl1271: uploading fw last chunk (176 B) 0xd089b4b0 to 0x316e00
[ 195.884368] wl1271: ERROR sdio read failed (-110)
[ 195.884460] wl1271: ERROR sdio write failed (-110)
[ 197.282745] wl1271: ERROR sdio read failed (-110)
[ 197.282775] wl1271: chip id after firmware boot: 0x101
[ 197.282775] wl1271: ERROR chip id doesn't match after firmware boot
[ 197.282867] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
[ 197.282958] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
[ 197.282989] wl1271: ERROR firmware boot failed despite 3 retries
[ 197.282989] wl1271: mac80211 stop
Hi Joerie,
On Tue, Nov 30, 2010 at 11:35 AM, Joerie de Gram <[email protected]> wrote:
> Now I've got it to work using the firmware recently contributed to
> linux-firmware by TI, but I've run into another issue. The first time
> the interface is brought up everything appears to work fine (a scan
> returns APs), but once I bring the interface down any subsequent
> attempt to bring the interface back up again fail.
Make sure you have CONFIG_REGULATOR_FIXED_VOLTAGE enabled, and please
send us a full terminal log from boot to first error after applying
the following patch:
diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c
index 2fe9d99..6476137 100644
--- a/drivers/regulator/fixed.c
+++ b/drivers/regulator/fixed.c
@@ -49,6 +49,7 @@ static int fixed_voltage_enable(struct regulator_dev *dev)
struct fixed_voltage_data *data = rdev_get_drvdata(dev);
if (gpio_is_valid(data->gpio)) {
+ pr_info("%s %d\n", __func__, data->gpio);
gpio_set_value_cansleep(data->gpio, data->enable_high);
data->is_enabled = true;
}
@@ -61,6 +62,7 @@ static int fixed_voltage_disable(struct regulator_dev *dev)
struct fixed_voltage_data *data = rdev_get_drvdata(dev);
if (gpio_is_valid(data->gpio)) {
+ pr_info("%s %d\n", __func__, data->gpio);
gpio_set_value_cansleep(data->gpio, !data->enable_high);
data->is_enabled = false;
}
In addition, please execute 'cat /sys/kernel/debug/mmc2/ios' (so we
can see the results in the log) at the following points:
1. right after boot
2. after insmodding the drivers
3. after bringing up wlan0
4. after taking wlan0 down
5. after the second attempt to bring up wlan0
(obviously you will have to mount -t debugfs none /sys/kernel/debug for that)
>
> Sysfs indicates that after the interface has been brought down, the
> MMC regulator (VSIM) and the WLAN_PMENA GPIO remain enabled. Is this
> correct behavior?
>
> Upon the second ifup it seems to first fail waiting for an "init
> complete" interrupt (WL1271_ACX_INTR_INIT_COMPLETE).
>
> As for the regulators, I'm still not sure if I've configured them
> correctly (especially the consumer structs).
>
> I'm running v2.6.36 with Ohad's patches to allow wl1271 configuration
> in the board code and have also applied the runtime PM patchset
> (http://www.spinics.net/lists/linux-wireless/msg56664.html).
>
> Relevant code snippets below, as well as the kernel log
>
> Joerie
>
> ---------------------------------------------------------------
>
> #define NOWPLUS_WLAN_IRQ_GPIO ? ? ? ? ? 21
> #define NOWPLUS_WLAN_PMENA_GPIO ? ? ? ? 160
>
> static struct regulator_consumer_supply nowplus_vsim_supply = {
> ? ? ? ?.supply ? ? ? ? ? ? ? ? = "vmmc",
> };
>
>
> static struct regulator_consumer_supply nowplus_wl1271_supply = {
> ? ? ? ?.supply ? ? ? ? ? ? ? ? = "vmmc_aux",
> ? ? ? ?.dev_name ? ? ? ? ? ? ? = "mmci-omap-hs.2",
> };
>
> /* VSIM for WiFi SDIO */
> static struct regulator_init_data nowplus_vsim = {
> ? ? ? ?.constraints = {
> ? ? ? ? ? ? ? ?.name ? ? ? ? ? ? ? ? ? = "VSIM",
> ? ? ? ? ? ? ? ?.min_uV ? ? ? ? ? ? ? ? = 1800000,
> ? ? ? ? ? ? ? ?.max_uV ? ? ? ? ? ? ? ? = 1800000,
> ? ? ? ? ? ? ? ?.apply_uV ? ? ? ? ? ? ? = true,
> ? ? ? ? ? ? ? ?.valid_modes_mask ? ? ? = REGULATOR_MODE_NORMAL
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| REGULATOR_MODE_STANDBY,
> ? ? ? ? ? ? ? ?.valid_ops_mask ? ? ? ? = REGULATOR_CHANGE_MODE
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| REGULATOR_CHANGE_STATUS,
> ? ? ? ?},
> ? ? ? ?.num_consumer_supplies ?= 1,
> ? ? ? ?.consumer_supplies ? ? ?= &nowplus_vsim_supply,
> };
>
> static struct regulator_init_data nowplus_wlgpio = {
> ? ? ? ?.constraints = {
> ? ? ? ? ? ? ? ?.valid_ops_mask = REGULATOR_CHANGE_STATUS,
> ? ? ? ?},
> ? ? ? ?.num_consumer_supplies ?= 1,
> ? ? ? ?.consumer_supplies ? ? ?= &nowplus_wl1271_supply,
> };
>
> static struct fixed_voltage_config nowplus_vwlan = {
> ? ? ? ?.supply_name ? ? ? ? ? ?= "vwl1271",
> ? ? ? ?.microvolts ? ? ? ? ? ? = 1800000, /* 1.8V */
> ? ? ? ?.gpio ? ? ? ? ? ? ? ? ? = NOWPLUS_WLAN_PMENA_GPIO,
> ? ? ? ?.startup_delay ? ? ? ? ?= 70000, /* 70msec */
> ? ? ? ?.enable_high ? ? ? ? ? ?= 1,
> ? ? ? ?.enabled_at_boot ? ? ? ?= 0,
> ? ? ? ?.init_data ? ? ? ? ? ? ?= &nowplus_wlgpio,
> };
>
> static struct platform_device nowplus_vwlan_device = {
> ? ? ? ?.name ? ? ? ? ? = "reg-fixed-voltage",
> ? ? ? ?.id ? ? ? ? ? ? = 1,
> ? ? ? ?.dev = {
> ? ? ? ? ? ? ? ?.platform_data ?= &nowplus_vwlan,
> ? ? ? ?},
> };
>
> static int nowplus_twl_gpio_setup(struct device *dev,
> ? ? ? ? ? ? ? ?unsigned gpio, unsigned ngpio)
> {
> ? ? ? ?omap2_hsmmc_init(nowplus_mmc);
>
> ? ? ? ?/* link regulators to MMC adapters */
> ? ? ? ?nowplus_vmmc1_supply.dev = nowplus_mmc[0].dev;
> ? ? ? ?nowplus_vmmc2_supply.dev = nowplus_mmc[1].dev;
> ? ? ? ?nowplus_vsim_supply.dev = nowplus_mmc[2].dev;
>
> ? ? ? ?return 0;
> }
>
> ---------------------------------------------------------------
>
> [ ? ?1.475463] mmc2: card claims to support voltages below the defined
> range. These will be ignored.
> [ ? ?1.518280] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
> [ ? ?1.535400] mmc2: new SDIO card at address 0001
> [ ? ?1.540435] PM: Adding info for mmc:mmc2:0001
> [ ? ?1.545562] PM: Adding info for sdio:mmc2:0001:1
> [ ? ?1.550689] wl1271_sdio mmc2:0001:1: __pm_runtime_resume()!
> [ ? ?1.559722] mmc mmc2:0001: __pm_runtime_resume()!
> [ ? ?1.564270] mmc mmc2:0001: __pm_runtime_resume() returns 1!
> [ ? ?1.573120] wl1271_sdio mmc2:0001:1: __pm_runtime_resume() returns 0!
> [ ? ?1.582061] sdio mmc2:0001:1: __pm_runtime_suspend()!
> [ ? ?1.586608] sdio mmc2:0001:1: __pm_runtime_suspend() returns 0!
> [ ? ?1.595397] PM: Adding info for sdio:mmc2:0001:2
> [ ? ?1.600219] wl1271_sdio mmc2:0001:2: __pm_runtime_resume()!
> [ ? ?1.609069] mmc mmc2:0001: __pm_runtime_resume()!
> [ ? ?1.613464] mmc mmc2:0001: __pm_runtime_resume() returns 1!
> [ ? ?1.622375] wl1271_sdio mmc2:0001:2: __pm_runtime_resume() returns 0!
> [ ? ?1.632232] PM: Adding info for platform:wl1271
> [ ? ?1.637268] PM: Adding info for No Bus:phy0
> [ ? ?1.643096] PM: Adding info for No Bus:wlan0
> [ ? ?1.648162] wl1271: loaded
> [ ? ?1.652587] wl1271: initialized
> [ ? ?1.656768] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
> [ ? ?1.665130] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
> [ ? ?6.197753] Freeing init memory: 136K
> [ ? ?6.510559] PM: Adding info for No Bus:vcs2
> [ ? ?6.511383] PM: Adding info for No Bus:vcsa2
> [ ? 13.935028] wl1271: mac80211 start
> [ ? 13.935058] wl1271: mac80211 stop
> [ ? 24.939239] usb0: no IPv6 routers present
>
> <wlan0 brought up>
>
> --- wlan0 down ---
> [ ?161.776367] wl1271: mac80211 configure filter
> [ ?161.776397] wl1271: waking up chip from elp
> [ ?161.776702] wl1271: mac80211 configure filter
> [ ?161.782470] wl1271: IRQ
> [ ?161.782531] wl1271: wakeup time: 0 ms
> [ ?161.782531] wl1271: acx group address tbl
> [ ?161.782562] wl1271: cmd configure
> [ ?161.783325] wl1271: IRQ work
> [ ?161.783447] wl1271: intr: 0x20 (fw_rx_counter = 0, drv_rx_counter =
> 0, tx_results_counter = 0)
> [ ?161.783477] wl1271: WL1271_ACX_INTR_HW_AVAILABLE
> [ ?161.783508] wl1271: acx group address tbl
> [ ?161.783508] wl1271: cmd configure
> [ ?161.783966] wl1271: mac80211 remove interface
> [ ?161.783996] wl1271: down
> [ ?161.784088] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
> [ ?161.784149] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
> [ ?161.784179] wl1271: mac80211 stop
> [ ?161.790985] wl1271: elp work
>
> --- wlan0 up ---
> [ ?189.104309] wl1271: mac80211 start
> [ ?189.104339] wl1271: mac80211 add interface type 2 mac a0:07:98:6a:f8:c7
> [ ?189.134704] wl1271_sdio mmc2:0001:2: __pm_runtime_resume()!
> [ ?189.134735] mmc mmc2:0001: __pm_runtime_resume()!
> [ ?189.134765] mmc mmc2:0001: __pm_runtime_resume() returns 1!
> [ ?189.134796] wl1271_sdio mmc2:0001:2: __pm_runtime_resume() returns 0!
> [ ?189.345672] wl1271: mem_start 00000000 mem_size 00000000
> [ ?189.345703] wl1271: reg_start 00300000 reg_size 00008800
> [ ?189.345703] wl1271: mem2_start 00000000 mem2_size 00000000
> [ ?189.345733] wl1271: mem3_start 00000000 mem3_size 00000000
> [ ?189.346252] wl1271: chip id 0x4030111 (1271 PG20)
> [ ?189.346954] wl1271: pause1 0x40f73
> [ ?189.347534] wl1271: mem_start 00040000 mem_size 00014FC0
> [ ?189.347564] wl1271: reg_start 00310000 reg_size 00006000
> [ ?189.347564] wl1271: mem2_start 00000000 mem2_size 00000000
> [ ?189.347595] wl1271: mem3_start 00000000 mem3_size 00000000
> [ ?189.347900] wl1271: DRPW_SCRATCH_START 0031002c
> [ ?189.347961] wl1271: clk2 0x80316a2c
> [ ?189.348022] wl1271: mem_start 00040000 mem_size 00014FC0
> [ ?189.348022] wl1271: reg_start 00300000 reg_size 0000A000
> [ ?189.348052] wl1271: mem2_start 003004F8 mem2_size 00000004
> [ ?189.348052] wl1271: mem3_start 00040404 mem3_size 00000000
> [ ?189.348480] wl1271: soft reset bootdata 0x0
> [ ?189.348571] wl1271: nvs burst write 0x30546c: 0x986af8c7
> [ ?189.348632] wl1271: nvs burst write 0x305470: 0xa007
> [ ?189.348693] wl1271: mem_start 00040000 mem_size 00014FC0
> [ ?189.348724] wl1271: reg_start 00300000 reg_size 0000A000
> [ ?189.348724] wl1271: mem2_start 003004F8 mem2_size 00000004
> [ ?189.348754] wl1271: mem3_start 00040404 mem3_size 00000000
> [ ?189.349121] wl1271: ACX_EEPROMLESS_IND_REG
> [ ?189.349212] wl1271: chip id 0x4030111
> [ ?189.349548] wl1271: firmware chunks to be uploaded: 6
> [ ?189.349578] wl1271: chunk 5 addr 0x0 len 195924
> [ ?189.349609] wl1271: starting firmware upload
> [ ?189.349609] wl1271: fw_data_len 195924 chunk_size 512
> [ ?189.349639] wl1271: mem_start 00000000 mem_size 000177C0
> [ ?189.349639] wl1271: reg_start 00300000 reg_size 00008800
> [ ?189.349670] wl1271: mem2_start 00000000 mem2_size 00000000
> [ ?189.349670] wl1271: mem3_start 00000000 mem3_size 00000000
> [ ?189.349975] wl1271: uploading fw chunk 0xd085900c to 0x0
> <...>
> [ ?191.986022] wl1271: uploading fw last chunk (176 B) 0xd089b4b0 to 0x316e00
> [ ?191.986297] wl1271: chip id after firmware boot: 0x4030111
> [ ?194.105377] wl1271: ERROR timeout waiting for the hardware to
> complete initialization
> <...>
> [ ?194.485961] wl1271: uploading fw last chunk (176 B) 0xd089b4b0 to 0x316e00
> [ ?195.884368] wl1271: ERROR sdio read failed (-110)
> [ ?195.884460] wl1271: ERROR sdio write failed (-110)
> [ ?197.282745] wl1271: ERROR sdio read failed (-110)
> [ ?197.282775] wl1271: chip id after firmware boot: 0x101
> [ ?197.282775] wl1271: ERROR chip id doesn't match after firmware boot
> [ ?197.282867] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend()!
> [ ?197.282958] wl1271_sdio mmc2:0001:2: __pm_runtime_suspend() returns 0!
> [ ?197.282989] wl1271: ERROR firmware boot failed despite 3 retries
> [ ?197.282989] wl1271: mac80211 stop
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to [email protected]
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
Hi,
On Wed, Dec 1, 2010 at 2:36 AM, Ohad Ben-Cohen <[email protected]> wrote:
> On Tue, Nov 30, 2010 at 3:30 PM, Joerie de Gram <[email protected]> wrote:
>> The regulator is only enabled once. Equally, the MMC interface is
>> initialised only at boot, and remains untouched afterwards.
>
> Even if the wl12xx sdio driver is still not loaded ?
Yes.
> Can you pls send me your drivers/mmc/core/sdio.c to have a look ? Or
> probably better, can you share the entire kernel ? and your .config ?
I have pushed my development tree to:
http://h1.pargon.nl/gitweb/gitweb.cgi?p=kernel.git;a=shortlog;h=refs/heads/wireless
Board is called board-nowplus, current config is nowplus_defconfig.
Joerie
On Tue, Nov 30, 2010 at 3:30 PM, Joerie de Gram <[email protected]> wrote:
> The regulator is only enabled once. Equally, the MMC interface is
> initialised only at boot, and remains untouched afterwards.
Even if the wl12xx sdio driver is still not loaded ?
Can you pls send me your drivers/mmc/core/sdio.c to have a look ? Or
probably better, can you share the entire kernel ? and your .config ?
Thanks,
Ohad.
Hi Ohad,
On Tue, Nov 30, 2010 at 10:59 PM, Ohad Ben-Cohen <[email protected]> wrote:
> Make sure you have CONFIG_REGULATOR_FIXED_VOLTAGE enabled, and please
> send us a full terminal log from boot to first error after applying
> the following patch:
The regulator is only enabled once. Equally, the MMC interface is
initialised only at boot, and remains untouched afterwards. It's
config doesn't change:
clock: 25000000 Hz
vdd: 7 (1.65 - 1.95 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 0 (legacy)
Full kernel log (rather large): http://130.89.163.61/dmesg
What concerns me is the regulator config - most boards seem to call
the fixed regulator vmmc, but I require VSIM as well to power the card
(which requires it to be labeled vmmc for the mmc subsystem?).
Joerie
Hi,
On Thu, Dec 2, 2010 at 5:23 PM, Ohad Ben-Cohen <[email protected]> wrote:
> You forgot to apply 516d5cc "mmc: add runtime PM handlers":
Problem solved, it appears to work just fine now. Thanks (again).
Joerie
On Wed, Dec 1, 2010 at 12:40 PM, Joerie de Gram <[email protected]> wrote:
> I have pushed my development tree to:
> http://h1.pargon.nl/gitweb/gitweb.cgi?p=kernel.git;a=shortlog;h=refs/heads/wireless
You forgot to apply 516d5cc "mmc: add runtime PM handlers":
http://www.spinics.net/lists/linux-mmc/msg03970.html
Without that patch, MMC core doesn't tell PM core how to control the
power of the wl1271 device, so you're left with it powered on after
boot.