I wanted to test the new "AP mode" functionality in the mwifiex driver so I
built a kernel off the wireless-testing tree and hostapd v2.0-devel from git.
I tried this on a "DreamPlug" that uses the SD8787.
"Client mode" is working fine, but I can't seem to be able to get "AP mode"
working. No matter what I do I get this output from hostapd:
random: Trying to read entropy from /dev/random
Configuration file: hostapd-minimal.conf
nl80211: interface uap0 in phy phy0
rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
nl80211: Disable use_monitor with device_ap_sme since no monitor mode support d
etected
nl80211: Add own interface ifindex 5
nl80211: Set mode ifindex 5 iftype 3 (AP)
nl80211: Setup AP - device_ap_sme=1 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x74608 (device SME)
nl80211: Register frame type=0xd0 nl_handle=0x74608
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Register frame command failed (type=208): ret=-95 (Operation not suppo
rted)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Failed to set interface uap0 into AP mode
netlink: Operstate: linkmode=0, operstate=6
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Try mode change after setting interface down
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
[ ... ]
nl80211: Interface mode change to 2 from 3 failed
nl80211 driver initialization failed.
I've tried bringing both mlan0 and uap0 interfaces down/up and different
combinations of both to no avail. The patches for "AP mode" support mention
that is has been tested against hostapd v2.0-devel. Is there anything I should
be aware of when building hostapd? I'm also not sure if I'm running the correct
firmware for the SD8787.
Thanks in advance for any input!!!
Hans
--- mwifiex_sdio firmware ---
mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld
mwifiex_sdio mmc0:0001:1: WLAN FW is active
mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (14.57.5.p69)
--- hostapd .config ---
CONFIG_DRIVER_HOSTAP=y
CONFIG_DRIVER_NL80211=y
CONFIG_LIBNL32=y
CFLAGS += -I/usr/include/libnl3
CONFIG_IAPP=y
CONFIG_RSN_PREAUTH=y
CONFIG_PEERKEY=y
CONFIG_EAP=y
CONFIG_EAP_MD5=y
CONFIG_EAP_TLS=y
CONFIG_EAP_MSCHAPV2=y
CONFIG_EAP_PEAP=y
CONFIG_EAP_GTC=y
CONFIG_EAP_TTLS=y
CONFIG_PKCS12=y
CONFIG_IPV6=y
CONFIG_IEEE80211N=y
--- hostatp-minimal.conf ---
interface=uap0
driver=nl80211
ssid=DreamPlug
hw_mode=g
channel=1
Hi Hans,
mwifiex AP functionality has been tested against following hostapd revision:
http://hostap.epitest.fi/gitweb/gitweb.cgi?p=hostap.git;a=snapshot;h=5f32f79c6e071f02076e09931adc8fc4e0ecd383;sf=tgz
Can you please test mwifiex AP setup against this hostapd revision and
let me know result?
Regards,
Avinash
On Thu, Jun 7, 2012 at 3:53 PM, Hans Kr?ner <[email protected]> wrote:
> Hi Avinash,
>
> Thanks for your reply!
>
> i) ? ?Firmware version is reported as "mwifiex 1.0 (14.57.5.p69)"
>
> ii) ? hostapd version is "v2.0-devel" I took it from git at
> ? ? ?git://w1.fi/srv/git/hostap.git and used the config in my previous post
> ? ? ?to build it. I'm at commit 5b3763336466f2c55611437cb924aeee45f7203e
>
> iii) ?Output of hostapd "-ddd" is the same as my previous post, which used
> ? ? ?"-dd". Here it is:
>
> ? ? ? ? ? ? ? ?random: Trying to read entropy from /dev/random
> ? ? ? ? ? ? ? ?Configuration file: hostapd-minimal.conf
> ? ? ? ? ? ? ? ?nl80211: interface uap0 in phy phy0
> ? ? ? ? ? ? ? ?rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0
> ? ? ? ? ? ? ? ?rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
> ? ? ? ? ? ? ? ?nl80211: Disable use_monitor with device_ap_sme since no monitor mode
> ? ? ? ? ? ? ? ?support detected
> ? ? ? ? ? ? ? ?nl80211: Add own interface ifindex 5
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 3 (AP)
> ? ? ? ? ? ? ? ?nl80211: Setup AP - device_ap_sme=1 use_monitor=0
> ? ? ? ? ? ? ? ?nl80211: Subscribe to mgmt frames with AP handle 0x74608 (device SME)
> ? ? ? ? ? ? ? ?nl80211: Register frame type=0xd0 nl_handle=0x74608
> ? ? ? ? ? ? ? ?nl80211: Register frame match - hexdump(len=0): [NULL]
> ? ? ? ? ? ? ? ?nl80211: Register frame command failed (type=208): ret=-95 (Operation not
> ? ? ? ? ? ? ? ?supported)
> ? ? ? ? ? ? ? ?nl80211: Register frame match - hexdump(len=0): [NULL]
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface uap0 into AP mode
> ? ? ? ? ? ? ? ?netlink: Operstate: linkmode=0, operstate=6
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Try mode change after setting interface down
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Set mode ifindex 5 iftype 2 (STATION)
> ? ? ? ? ? ? ? ?nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> ? ? ? ? ? ? ? ?nl80211: Interface mode change to 2 from 3 failed
> ? ? ? ? ? ? ? ?nl80211 driver initialization failed.
>
> Thanks for your help!!!
>
> Best Regards,
>
> Hans
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to [email protected]
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
Hi Hans,
> I wanted to test the new "AP mode" functionality in the mwifiex driver so I
> built a kernel off the wireless-testing tree and hostapd v2.0-devel from git.
> I tried this on a "DreamPlug" that uses the SD8787.
>
> "Client mode" is working fine, but I can't seem to be able to get "AP mode"
> working. No matter what I do I get this output from hostapd:
[...]
> I've tried bringing both mlan0 and uap0 interfaces down/up and different
> combinations of both to no avail. The patches for "AP mode" support mention
> that is has been tested against hostapd v2.0-devel. Is there anything I should
> be aware of when building hostapd?
The latest hostapd code requires mgmt handlers which we are still working on.
Please checkout the commit id mentioned by Avinash.
> I'm also not sure if I'm running the correct firmware for the SD8787.
[...]
> mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (14.57.5.p69)
Please get the latest firmware image (14.66.9.p80) here:
git://git.marvell.com/mwifiex-firmware.git
http://git.marvell.com/?p=mwifiex-firmware.git;a=summary
Thanks,
Bing
Hello Hans,
My libnl version libnl-1.
Also there are no changes in .config. Simply copy defconfig to .config.
Regards,
Avinash
On Thu, Jun 7, 2012 at 4:34 PM, Hans Kr?ner <[email protected]> wrote:
> Hi Avinash,
>
> I'll try to build that version in a little while. At the time of that revision,
> hostapd could not be linked against libnl-3. When you built the version you
> tested against, were you using libnl-1 or libnl-2?
>
> Could you provide me with the .config file you used to build hostapd so I can
> be sure that I'm not including things I shouldn't be, or missing important
> parts?
>
> Thanks again!
>
> Best Regards,
>
> Hans
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to [email protected]
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
Hello Hans,
Can you please let me know:
i. mwifiex FW version: you can get this value while loading driver in dmesg.
ii. hostapd version
iii. Also can you please put extended logs by -ddd command line parameter.
mwifiex AP mode is supported for hostapd develv2 only.
Regards,
Avinash
On Thu, Jun 7, 2012 at 1:48 PM, Hans Kr?ner <[email protected]> wrote:
> I wanted to test the new "AP mode" functionality in the mwifiex driver so I
> built a kernel off the wireless-testing tree and hostapd v2.0-devel from git.
> I tried this on a "DreamPlug" that uses the SD8787.
>
> "Client mode" is working fine, but I can't seem to be able to get "AP mode"
> working. No matter what I do I get this output from hostapd:
>
> random: Trying to read entropy from /dev/random
> Configuration file: hostapd-minimal.conf
> nl80211: interface uap0 in phy phy0
> rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0
> rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
> nl80211: Disable use_monitor with device_ap_sme since no monitor mode support d
> etected
> nl80211: Add own interface ifindex 5
> nl80211: Set mode ifindex 5 iftype 3 (AP)
> nl80211: Setup AP - device_ap_sme=1 use_monitor=0
> nl80211: Subscribe to mgmt frames with AP handle 0x74608 (device SME)
> nl80211: Register frame type=0xd0 nl_handle=0x74608
> nl80211: Register frame match - hexdump(len=0): [NULL]
> nl80211: Register frame command failed (type=208): ret=-95 (Operation not suppo
> rted)
> nl80211: Register frame match - hexdump(len=0): [NULL]
> nl80211: Failed to set interface uap0 into AP mode
> netlink: Operstate: linkmode=0, operstate=6
> nl80211: Set mode ifindex 5 iftype 2 (STATION)
> nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> nl80211: Try mode change after setting interface down
> nl80211: Set mode ifindex 5 iftype 2 (STATION)
> nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> nl80211: Set mode ifindex 5 iftype 2 (STATION)
> nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
> [ ... ]
> nl80211: Interface mode change to 2 from 3 failed
> nl80211 driver initialization failed.
>
> I've tried bringing both mlan0 and uap0 interfaces down/up and different
> combinations of both to no avail. The patches for "AP mode" support mention
> that is has been tested against hostapd v2.0-devel. Is there anything I should
> be aware of when building hostapd? I'm also not sure if I'm running the correct
> firmware for the SD8787.
>
> Thanks in advance for any input!!!
>
> Hans
>
>
> --- mwifiex_sdio firmware ---
>
> mwifiex_sdio mmc0:0001:1: WLAN FW already running! Skip FW dnld
> mwifiex_sdio mmc0:0001:1: WLAN FW is active
> mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (14.57.5.p69)
>
> --- hostapd .config ---
>
> CONFIG_DRIVER_HOSTAP=y
> CONFIG_DRIVER_NL80211=y
> CONFIG_LIBNL32=y
> CFLAGS += -I/usr/include/libnl3
> CONFIG_IAPP=y
> CONFIG_RSN_PREAUTH=y
> CONFIG_PEERKEY=y
> CONFIG_EAP=y
> CONFIG_EAP_MD5=y
> CONFIG_EAP_TLS=y
> CONFIG_EAP_MSCHAPV2=y
> CONFIG_EAP_PEAP=y
> CONFIG_EAP_GTC=y
> CONFIG_EAP_TTLS=y
> CONFIG_PKCS12=y
> CONFIG_IPV6=y
> CONFIG_IEEE80211N=y
>
> --- hostatp-minimal.conf ---
>
> interface=uap0
> driver=nl80211
> ssid=DreamPlug
> hw_mode=g
> channel=1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
> the body of a message to [email protected]
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
Hi Avinash,
I'll try to build that version in a little while. At the time of that revision,
hostapd could not be linked against libnl-3. When you built the version you
tested against, were you using libnl-1 or libnl-2?
Could you provide me with the .config file you used to build hostapd so I can
be sure that I'm not including things I shouldn't be, or missing important
parts?
Thanks again!
Best Regards,
Hans
Hi Avinash,
Thanks for your reply!
i) Firmware version is reported as "mwifiex 1.0 (14.57.5.p69)"
ii) hostapd version is "v2.0-devel" I took it from git at
git://w1.fi/srv/git/hostap.git and used the config in my previous post
to build it. I'm at commit 5b3763336466f2c55611437cb924aeee45f7203e
iii) Output of hostapd "-ddd" is the same as my previous post, which used
"-dd". Here it is:
random: Trying to read entropy from /dev/random
Configuration file: hostapd-minimal.conf
nl80211: interface uap0 in phy phy0
rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
nl80211: Disable use_monitor with device_ap_sme since no monitor mode
support detected
nl80211: Add own interface ifindex 5
nl80211: Set mode ifindex 5 iftype 3 (AP)
nl80211: Setup AP - device_ap_sme=1 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x74608 (device SME)
nl80211: Register frame type=0xd0 nl_handle=0x74608
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Register frame command failed (type=208): ret=-95 (Operation not
supported)
nl80211: Register frame match - hexdump(len=0): [NULL]
nl80211: Failed to set interface uap0 into AP mode
netlink: Operstate: linkmode=0, operstate=6
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Try mode change after setting interface down
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Failed to set interface 5 to mode 2: -16 (Device or resource busy)
nl80211: Interface mode change to 2 from 3 failed
nl80211 driver initialization failed.
Thanks for your help!!!
Best Regards,
Hans