Hello, I've been trying to use an intel ax210 minipcie board on an arm32 platform. I could use an intel ax200 on the same platform without issues but with the ax210 it always fail.
How can I assist in debugging this issue ?
Below are some system information and the output of dmesg when loading iwlwifi:
lspci -k
00:00.0 PCI bridge: Xilinx Corporation Device 7121
01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
Subsystem: Intel Corporation Device 0024
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
md5sum /lib/firmware/*
787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
33d13d236512466e71c81257209a356f ./regulatory.db
uname -a
Linux BV1-26804 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
dmesg
pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
Intel(R) Wireless WiFi driver for Linux
pci 0000:00:00.0: enabling device (0140 -> 0142)
iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x000529AD | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x0006680C | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x00C89002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x000668FF | frame pointer
iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080BD | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 0
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x00051864 | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x0006561F | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x18C89002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0x8046C930 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0x8046C930 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x00065713 | frame pointer
iwlwifi 0000:01:00.0: 0xC088623C | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 1
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x00051D19 | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x00065AD6 | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x18C89002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0xC00818E0 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0xC00818E0 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x00065BCA | frame pointer
iwlwifi 0000:01:00.0: 0xC0886228 | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 2
On Fri, 2022-10-14 at 14:42 +0200, Florian Schmidt wrote:
> Hello, I've been trying to use an intel ax210 minipcie board on an arm32 platform. I could use an intel ax200 on the same platform without issues but with the ax210 it always fail.
>
> How can I assist in debugging this issue ?
>
> Below are some system information and the output of dmesg when loading iwlwifi:
>
> lspci -k
> 00:00.0 PCI bridge: Xilinx Corporation Device 7121
> 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> Subsystem: Intel Corporation Device 0024
> Kernel driver in use: iwlwifi
> Kernel modules: iwlwifi
>
> md5sum /lib/firmware/*
> 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> 33d13d236512466e71c81257209a356f ./regulatory.db
>
> uname -a
> Linux BV1-26804 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
>
> dmesg
> pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
> pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
> pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
> pci 0000:00:00.0: PCI bridge to [bus 01]
> pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
> Intel(R) Wireless WiFi driver for Linux
> pci 0000:00:00.0: enabling device (0140 -> 0142)
> iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
> iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
> iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
> iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
> iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x000529AD | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x0006680C | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x00C89002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x000668FF | frame pointer
> iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080BD | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 0
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x00051864 | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x0006561F | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x18C89002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0x8046C930 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0x8046C930 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x00065713 | frame pointer
> iwlwifi 0000:01:00.0: 0xC088623C | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 1
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x00051D19 | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x00065AD6 | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x18C89002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0xC00818E0 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0xC00818E0 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x00065BCA | frame pointer
> iwlwifi 0000:01:00.0: 0xC0886228 | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 2
The problem here (at least what I can understand from the log) is that the PNVM binary is missing.
Indeed, it's not required for ax200 device, but it's needed for ax210 device.
You can take iwlwifi-ty-a0-gf-a0.pnvm from
http://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git and place it along with
the frimware file in /lib/firmware.
HTH,
Gregory
Hi Gregory,
Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> md5sum /lib/firmware/*
> 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> 33d13d236512466e71c81257209a356f ./regulatory.db
I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
Any other ideas to solve this are welcome.
Thanks,
Florian
On 2022-10-26T16:13:16.000+02:00, Greenman Gregory <[email protected]> wrote:
> On Fri, 2022-10-14 at 14:42 +0200, Florian Schmidt wrote:
>
> > Hello, I've been trying to use an intel ax210 minipcie board on an arm32 platform. I could use an intel ax200 on the same platform without issues but with the ax210 it always fail.
> >
> > How can I assist in debugging this issue ?
> >
> > Below are some system information and the output of dmesg when loading iwlwifi:
> >
> > lspci -k
> > 00:00.0 PCI bridge: Xilinx Corporation Device 7121
> > 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> > Subsystem: Intel Corporation Device 0024
> > Kernel driver in use: iwlwifi
> > Kernel modules: iwlwifi
> >
> > md5sum /lib/firmware/*
> > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > 33d13d236512466e71c81257209a356f ./regulatory.db
> >
> > uname -a
> > Linux BV1-26804 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
> >
> > dmesg
> > pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
> > pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> > pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
> > pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
> > pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
> > pci 0000:00:00.0: PCI bridge to [bus 01]
> > pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
> > Intel(R) Wireless WiFi driver for Linux
> > pci 0000:00:00.0: enabling device (0140 -> 0142)
> > iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
> > iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
> > iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
> > iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
> > iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x000529AD | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x0006680C | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x00C89002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x000668FF | frame pointer
> > iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080BD | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 0
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x00051864 | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x0006561F | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x18C89002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0x8046C930 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0x8046C930 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x00065713 | frame pointer
> > iwlwifi 0000:01:00.0: 0xC088623C | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 1
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x00051D19 | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x00065AD6 | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x18C89002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0xC00818E0 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0xC00818E0 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x00065BCA | frame pointer
> > iwlwifi 0000:01:00.0: 0xC0886228 | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 2
>
> The problem here (at least what I can understand from the log) is that the PNVM binary is missing.
> Indeed, it's not required for ax200 device, but it's needed for ax210 device.
> You can take iwlwifi-ty-a0-gf-a0.pnvm from
> http://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git and place it along with
> the frimware file in /lib/firmware.
>
> HTH,
> Gregory
On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> Hi Gregory,
>
> Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
>> md5sum /lib/firmware/*
>> 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
>> d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
>> 33d13d236512466e71c81257209a356f ./regulatory.db
>
> I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
>
> Any other ideas to solve this are welcome.
The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
which you do seem to have based upon the listing above?
--
Florian
On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> On 10/26/2022 8:56 AM, Florian Schmidt wrote:
>
> > Hi Gregory,
> >
> > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> >
> > > md5sum /lib/firmware/*
> > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > 33d13d236512466e71c81257209a356f ./regulatory.db
> >
> > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> >
> > Any other ideas to solve this are welcome.
>
> The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> which you do seem to have based upon the listing above?
> --
> Florian
Hi Florian,
Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
Florian
-------
root@BV1-27109:/lib/firmware# md5sum /lib/firmware/*
787381c60d907f81a3ddadc5c990a82b /lib/firmware/iwlwifi-ty-a0-gf-a0-71.ucode
d93cbdcc4bb5be69aac128e2fe291359 /lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
33d13d236512466e71c81257209a356f /lib/firmware/regulatory.db
Linux BV1-27109 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
Intel(R) Wireless WiFi driver for Linux
pci 0000:00:00.0: enabling device (0140 -> 0142)
iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x00052ADD | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x00066975 | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x00489002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0x804792D6 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0x804792D6 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x00066ABB | frame pointer
iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 0
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x00053473 | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x0006722F | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x18489002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x00067375 | frame pointer
iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080EF | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 1
iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
thermal thermal_zone0: failed to read out thermal zone (-61)
iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
iwlwifi 0000:01:00.0: 0x004D9C78 | data1
iwlwifi 0000:01:00.0: 0x01000000 | data2
iwlwifi 0000:01:00.0: 0x00000000 | data3
iwlwifi 0000:01:00.0: 0x00000000 | beacon time
iwlwifi 0000:01:00.0: 0x00050982 | tsf low
iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
iwlwifi 0000:01:00.0: 0x00000000 | time gp1
iwlwifi 0000:01:00.0: 0x00064743 | time gp2
iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
iwlwifi 0000:01:00.0: 0x00000420 | hw version
iwlwifi 0000:01:00.0: 0x18489002 | board version
iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
iwlwifi 0000:01:00.0: 0x00020000 | isr0
iwlwifi 0000:01:00.0: 0x00000000 | isr1
iwlwifi 0000:01:00.0: 0x48F00002 | isr2
iwlwifi 0000:01:00.0: 0x00C0000C | isr3
iwlwifi 0000:01:00.0: 0x00000000 | isr4
iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
iwlwifi 0000:01:00.0: 0x00000000 | timestamp
iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
iwlwifi 0000:01:00.0: 0x804792E6 | umac interruptlink2
iwlwifi 0000:01:00.0: 0x01000000 | umac data1
iwlwifi 0000:01:00.0: 0x804792E6 | umac data2
iwlwifi 0000:01:00.0: 0x00000000 | umac data3
iwlwifi 0000:01:00.0: 0x00000047 | umac major
iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
iwlwifi 0000:01:00.0: 0x0006488D | frame pointer
iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
iwlwifi 0000:01:00.0: IML/ROM dump:
iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
iwlwifi 0000:01:00.0: 0x000080F3 | IML/ROM data1
iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
iwlwifi 0000:01:00.0: Fseq Registers:
iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: retry init count 2
On 10/26/22 10:37, Florian Schmidt wrote:
> On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
>
>> On 10/26/2022 8:56 AM, Florian Schmidt wrote:
>>
>>> Hi Gregory,
>>>
>>> Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
>>>
>>>> md5sum /lib/firmware/*
>>>> 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
>>>> d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
>>>> 33d13d236512466e71c81257209a356f ./regulatory.db
>>>
>>> I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
>>>
>>> Any other ideas to solve this are welcome.
>>
>> The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
>> which you do seem to have based upon the listing above?
>> --
>> Florian
>
> Hi Florian,
>
> Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
>
> Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
>
> I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
I am not familiar with ax210, but have worked quite a bit with the 7260
chips (iwlwifi) and errors like those typically occurred when the PCIe
end-point device, that is the ax210 is not able to do PCIe inbound
accesses into your system's memory. Now in your case it could be that
the inaility to load the appropriate ucode results in ... you guessed
it, the ucode not being loaded which causes the timeout to happen.
Can you tell us more about your ARM32 system here? What PCIe host
bridge/controller does it use, do you have an IOMMU attached to that
PCIe host brideg somehow?
Thanks!
>
> Florian
> -------
>
> root@BV1-27109:/lib/firmware# md5sum /lib/firmware/*
> 787381c60d907f81a3ddadc5c990a82b /lib/firmware/iwlwifi-ty-a0-gf-a0-71.ucode
> d93cbdcc4bb5be69aac128e2fe291359 /lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
> 33d13d236512466e71c81257209a356f /lib/firmware/regulatory.db
>
> Linux BV1-27109 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
>
> pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
> pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
> pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
> pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
> pci 0000:00:00.0: PCI bridge to [bus 01]
> pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
> Intel(R) Wireless WiFi driver for Linux
> pci 0000:00:00.0: enabling device (0140 -> 0142)
> iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
> iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
> iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
> iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
> iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x00052ADD | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x00066975 | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x00489002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0x804792D6 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0x804792D6 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x00066ABB | frame pointer
> iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 0
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x00053473 | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x0006722F | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x18489002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x00067375 | frame pointer
> iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080EF | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 1
> iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> thermal thermal_zone0: failed to read out thermal zone (-61)
> iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> iwlwifi 0000:01:00.0: 0x01000000 | data2
> iwlwifi 0000:01:00.0: 0x00000000 | data3
> iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> iwlwifi 0000:01:00.0: 0x00050982 | tsf low
> iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> iwlwifi 0000:01:00.0: 0x00064743 | time gp2
> iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> iwlwifi 0000:01:00.0: 0x00000420 | hw version
> iwlwifi 0000:01:00.0: 0x18489002 | board version
> iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> iwlwifi 0000:01:00.0: 0x00020000 | isr0
> iwlwifi 0000:01:00.0: 0x00000000 | isr1
> iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> iwlwifi 0000:01:00.0: 0x00000000 | isr4
> iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> iwlwifi 0000:01:00.0: 0x804792E6 | umac interruptlink2
> iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> iwlwifi 0000:01:00.0: 0x804792E6 | umac data2
> iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> iwlwifi 0000:01:00.0: 0x00000047 | umac major
> iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> iwlwifi 0000:01:00.0: 0x0006488D | frame pointer
> iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> iwlwifi 0000:01:00.0: IML/ROM dump:
> iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> iwlwifi 0000:01:00.0: 0x000080F3 | IML/ROM data1
> iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> iwlwifi 0000:01:00.0: Fseq Registers:
> iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> iwlwifi 0000:01:00.0: retry init count 2
--
Florian
On 2022-10-26T18:47:20.000+01:00, Florian Fainelli <[email protected]> wrote:
> On 10/26/22 10:37, Florian Schmidt wrote:
>
> > On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> >
> >
> > > On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> > >
> > >
> > > > Hi Gregory,
> > > >
> > > > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> > > >
> > > >
> > > > > md5sum /lib/firmware/*
> > > > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > > > 33d13d236512466e71c81257209a356f ./regulatory.db
> > > >
> > > > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> > > >
> > > > Any other ideas to solve this are welcome.
> > >
> > > The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> > > which you do seem to have based upon the listing above?
> > > --
> > > Florian
> >
> > Hi Florian,
> >
> > Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
> >
> > Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
> >
> > I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
>
> I am not familiar with ax210, but have worked quite a bit with the 7260
> chips (iwlwifi) and errors like those typically occurred when the PCIe
> end-point device, that is the ax210 is not able to do PCIe inbound
> accesses into your system's memory. Now in your case it could be that
> the inaility to load the appropriate ucode results in ... you guessed
> it, the ucode not being loaded which causes the timeout to happen.
>
> Can you tell us more about your ARM32 system here? What PCIe host
> bridge/controller does it use, do you have an IOMMU attached to that
> PCIe host brideg somehow?
>
> Thanks!
>
We're using a Xilinx FPGA Based PCIe root complex on a custom zynq-700 board. The doc of the PCIe block can be found here: https://www.xilinx.com/content/dam/xilinx/support/documents/ip_documentation/axi_pcie/v2_8/pg055-axi-bridge-pcie.pdf
I'm not really familiar with IOMMU (or PCIexpress) but to my knowledge there is no support of IOMMU on our arm32 platform, at least I couldn't enable it in kernel options, it required some other platform flags.
You can find everything lspci has to say about our device below.
root@BV1-27109:~# lspci -vv
00:00.0 PCI bridge: Xilinx Corporation Device 7121 (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff [size=4K]
Memory behind bridge: 00000000-000fffff [size=1M]
Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [60] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 1
ExtTag+ RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [128 v1] Vendor Specific Information: ID=0001 Rev=0 Len=038 <?>
Capabilities: [200 v1] Vendor Specific Information: ID=0002 Rev=0 Len=038 <?>
01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
Subsystem: Intel Corporation Device 0020
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 52
Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000001374000 Data: 0000
Capabilities: [40] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L1, Exit Latency L1 <8us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via WAKE#
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-, LTR-, OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [80] MSI-X: Enable- Count=16 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [14c v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [154 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=30us PortTPowerOnTime=18us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
Kernel modules: iwlwifi
> > Florian
> > -------
> >
> > root@BV1-27109:/lib/firmware# md5sum /lib/firmware/*
> > 787381c60d907f81a3ddadc5c990a82b /lib/firmware/iwlwifi-ty-a0-gf-a0-71.ucode
> > d93cbdcc4bb5be69aac128e2fe291359 /lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
> > 33d13d236512466e71c81257209a356f /lib/firmware/regulatory.db
> >
> > Linux BV1-27109 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
> >
> > pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
> > pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> > pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
> > pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
> > pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
> > pci 0000:00:00.0: PCI bridge to [bus 01]
> > pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
> > Intel(R) Wireless WiFi driver for Linux
> > pci 0000:00:00.0: enabling device (0140 -> 0142)
> > iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
> > iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
> > iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
> > iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
> > iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x00052ADD | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x00066975 | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x00489002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0x804792D6 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0x804792D6 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x00066ABB | frame pointer
> > iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 0
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x00053473 | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x0006722F | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x18489002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x00067375 | frame pointer
> > iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080EF | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 1
> > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > thermal thermal_zone0: failed to read out thermal zone (-61)
> > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > iwlwifi 0000:01:00.0: 0x00050982 | tsf low
> > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > iwlwifi 0000:01:00.0: 0x00064743 | time gp2
> > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > iwlwifi 0000:01:00.0: 0x18489002 | board version
> > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > iwlwifi 0000:01:00.0: 0x804792E6 | umac interruptlink2
> > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > iwlwifi 0000:01:00.0: 0x804792E6 | umac data2
> > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > iwlwifi 0000:01:00.0: 0x0006488D | frame pointer
> > iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > iwlwifi 0000:01:00.0: IML/ROM dump:
> > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > iwlwifi 0000:01:00.0: 0x000080F3 | IML/ROM data1
> > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > iwlwifi 0000:01:00.0: Fseq Registers:
> > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > iwlwifi 0000:01:00.0: retry init count 2
>
> --
> Florian
On Wed, 2022-10-26 at 20:11 +0200, Florian Schmidt wrote:
> On 2022-10-26T18:47:20.000+01:00, Florian Fainelli <[email protected]> wrote:
>
> > On 10/26/22 10:37, Florian Schmidt wrote:
> >
> > > On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> > >
> > >
> > > > On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> > > >
> > > >
> > > > > Hi Gregory,
> > > > >
> > > > > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> > > > >
> > > > >
> > > > > > md5sum /lib/firmware/*
> > > > > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > > > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > > > > 33d13d236512466e71c81257209a356f ./regulatory.db
> > > > >
> > > > > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> > > > >
> > > > > Any other ideas to solve this are welcome.
> > > >
> > > > The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> > > > which you do seem to have based upon the listing above?
> > > > --
> > > > Florian
> > >
> > > Hi Florian,
> > >
> > > Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with
> > > many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The
> > > suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
> > >
> > > Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
> > >
> > > I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
> >
> > I am not familiar with ax210, but have worked quite a bit with the 7260
> > chips (iwlwifi) and errors like those typically occurred when the PCIe
> > end-point device, that is the ax210 is not able to do PCIe inbound
> > accesses into your system's memory. Now in your case it could be that
> > the inaility to load the appropriate ucode results in ... you guessed
> > it, the ucode not being loaded which causes the timeout to happen.
> >
> > Can you tell us more about your ARM32 system here? What PCIe host
> > bridge/controller does it use, do you have an IOMMU attached to that
> > PCIe host brideg somehow?
> >
> > Thanks!
> >
>
> We're using a Xilinx FPGA Based PCIe root complex on a custom zynq-700 board. The doc of the PCIe block can be found here:
> https://www.xilinx.com/content/dam/xilinx/support/documents/ip_documentation/axi_pcie/v2_8/pg055-axi-bridge-pcie.pdf
>
> I'm not really familiar with IOMMU (or PCIexpress) but to my knowledge there is no support of IOMMU on our arm32 platform, at least I couldn't enable it in kernel options, it required some other
> platform flags.
>
> You can find everything lspci has to say about our device below.
>
> root@BV1-27109:~# lspci -vv
> 00:00.0 PCI bridge: Xilinx Corporation Device 7121 (prog-if 00 [Normal decode])
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00000000-00000fff [size=4K]
> Memory behind bridge: 00000000-000fffff [size=1M]
> Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] MSI: Enable- Count=1/32 Maskable+ 64bit+
> Address: 0000000000000000 Data: 0000
> Masking: 00000000 Pending: 00000000
> Capabilities: [60] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 256 bytes, PhantFunc 1
> ExtTag+ RBE+
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
> ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt+
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Off, PwrInd Off, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
> AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> AtomicOpsCtl: ReqEn- EgressBlck-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
> Capabilities: [128 v1] Vendor Specific Information: ID=0001 Rev=0 Len=038 <?>
> Capabilities: [200 v1] Vendor Specific Information: ID=0002 Rev=0 Len=038 <?>
>
> 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> Subsystem: Intel Corporation Device 0020
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 52
> Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [c8] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000001374000 Data: 0000
> Capabilities: [40] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ FLReset-
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L1, Exit Latency L1 <8us
> ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via WAKE#
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-, LTR-, OBFF Disabled
> AtomicOpsCtl: ReqEn-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [80] MSI-X: Enable- Count=16 Masked-
> Vector table: BAR=0 offset=00002000
> PBA: BAR=0 offset=00003000
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ AdvNonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
> AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 00000000 00000000 00000000 00000000
> Capabilities: [14c v1] Latency Tolerance Reporting
> Max snoop latency: 0ns
> Max no snoop latency: 0ns
> Capabilities: [154 v1] L1 PM Substates
> L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
> PortCommonModeRestoreTime=30us PortTPowerOnTime=18us
> L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
> T_CommonMode=0us LTR1.2_Threshold=0ns
> L1SubCtl2: T_PwrOn=10us
> Kernel modules: iwlwifi
>
>
> > > Florian
> > > -------
> > >
> > > root@BV1-27109:/lib/firmware# md5sum /lib/firmware/*
> > > 787381c60d907f81a3ddadc5c990a82b /lib/firmware/iwlwifi-ty-a0-gf-a0-71.ucode
> > > d93cbdcc4bb5be69aac128e2fe291359 /lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
> > > 33d13d236512466e71c81257209a356f /lib/firmware/regulatory.db
> > >
> > > Linux BV1-27109 6.0.1-xilinx #1 SMP PREEMPT Wed Oct 12 09:15:44 UTC 2022 armv7l GNU/Linux
> > >
> > > pci 0000:01:00.0: [8086:2725] type 00 class 0x028000
> > > pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
> > > pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
> > > pci 0000:00:00.0: BAR 8: assigned [mem 0x80000000-0x800fffff]
> > > pci 0000:01:00.0: BAR 0: assigned [mem 0x80000000-0x80003fff 64bit]
> > > pci 0000:00:00.0: PCI bridge to [bus 01]
> > > pci 0000:00:00.0: bridge window [mem 0x80000000-0x800fffff]
> > > Intel(R) Wireless WiFi driver for Linux
> > > pci 0000:00:00.0: enabling device (0140 -> 0142)
> > > iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
> > > iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-ty-a0-gf-a0-72.ucode failed with error -2
> > > iwlwifi 0000:01:00.0: api flags index 2 larger than supported by driver
> > > iwlwifi 0000:01:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 0.0.2.36
> > > iwlwifi 0000:01:00.0: loaded firmware version 71.058653f6.0 ty-a0-gf-a0-71.ucode op_mode iwlmvm
> > > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > > thermal thermal_zone0: failed to read out thermal zone (-61)
> > > iwlwifi 0000:01:00.0: loaded PNVM version a982b33e
> > > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > > iwlwifi 0000:01:00.0: 0x00052ADD | tsf low
> > > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > > iwlwifi 0000:01:00.0: 0x00066975 | time gp2
> > > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > > iwlwifi 0000:01:00.0: 0x00489002 | board version
> > > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > > iwlwifi 0000:01:00.0: 0x804792D6 | umac interruptlink2
> > > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > > iwlwifi 0000:01:00.0: 0x804792D6 | umac data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > > iwlwifi 0000:01:00.0: 0x00066ABB | frame pointer
> > > iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> > > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > > iwlwifi 0000:01:00.0: IML/ROM dump:
> > > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > > iwlwifi 0000:01:00.0: 0x000080F1 | IML/ROM data1
> > > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > > iwlwifi 0000:01:00.0: Fseq Registers:
> > > iwlwifi 0000:01:00.0: 0x20000000 | FSEQ_ERROR_CODE
> > > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > > iwlwifi 0000:01:00.0: retry init count 0
> > > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > > thermal thermal_zone0: failed to read out thermal zone (-61)
> > > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > > iwlwifi 0000:01:00.0: 0x00053473 | tsf low
> > > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > > iwlwifi 0000:01:00.0: 0x0006722F | time gp2
> > > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > > iwlwifi 0000:01:00.0: 0x18489002 | board version
> > > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink2
> > > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > > iwlwifi 0000:01:00.0: 0x8047E792 | umac data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > > iwlwifi 0000:01:00.0: 0x00067375 | frame pointer
> > > iwlwifi 0000:01:00.0: 0xC088625C | stack pointer
> > > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > > iwlwifi 0000:01:00.0: IML/ROM dump:
> > > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > > iwlwifi 0000:01:00.0: 0x000080EF | IML/ROM data1
> > > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > > iwlwifi 0000:01:00.0: Fseq Registers:
> > > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > > iwlwifi 0000:01:00.0: retry init count 1
> > > iwlwifi 0000:01:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420
> > > thermal thermal_zone0: failed to read out thermal zone (-61)
> > > iwlwifi 0000:01:00.0: Timeout waiting for PNVM load!
> > > iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
> > > iwlwifi 0000:01:00.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 6
> > > iwlwifi 0000:01:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
> > > iwlwifi 0000:01:00.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
> > > iwlwifi 0000:01:00.0: 0x002002F0 | trm_hw_status0
> > > iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
> > > iwlwifi 0000:01:00.0: 0x004DAEA2 | branchlink2
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink1
> > > iwlwifi 0000:01:00.0: 0x004D1336 | interruptlink2
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | data1
> > > iwlwifi 0000:01:00.0: 0x01000000 | data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | data3
> > > iwlwifi 0000:01:00.0: 0x00000000 | beacon time
> > > iwlwifi 0000:01:00.0: 0x00050982 | tsf low
> > > iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
> > > iwlwifi 0000:01:00.0: 0x00000000 | time gp1
> > > iwlwifi 0000:01:00.0: 0x00064743 | time gp2
> > > iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
> > > iwlwifi 0000:01:00.0: 0x00000047 | uCode version major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | uCode version minor
> > > iwlwifi 0000:01:00.0: 0x00000420 | hw version
> > > iwlwifi 0000:01:00.0: 0x18489002 | board version
> > > iwlwifi 0000:01:00.0: 0x8004FC12 | hcmd
> > > iwlwifi 0000:01:00.0: 0x00020000 | isr0
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr1
> > > iwlwifi 0000:01:00.0: 0x48F00002 | isr2
> > > iwlwifi 0000:01:00.0: 0x00C0000C | isr3
> > > iwlwifi 0000:01:00.0: 0x00000000 | isr4
> > > iwlwifi 0000:01:00.0: 0x00000000 | last cmd Id
> > > iwlwifi 0000:01:00.0: 0x004D9C78 | wait_event
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_control
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_duration
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_mhvalid
> > > iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
> > > iwlwifi 0000:01:00.0: 0x00000009 | lmpm_pmg_sel
> > > iwlwifi 0000:01:00.0: 0x00000000 | timestamp
> > > iwlwifi 0000:01:00.0: 0x00000020 | flow_handler
> > > iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
> > > iwlwifi 0000:01:00.0: Transport status: 0x00000042, valid: 7
> > > iwlwifi 0000:01:00.0: 0x20000066 | NMI_INTERRUPT_HOST
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
> > > iwlwifi 0000:01:00.0: 0x8045EFDC | umac branchlink2
> > > iwlwifi 0000:01:00.0: 0x8047E792 | umac interruptlink1
> > > iwlwifi 0000:01:00.0: 0x804792E6 | umac interruptlink2
> > > iwlwifi 0000:01:00.0: 0x01000000 | umac data1
> > > iwlwifi 0000:01:00.0: 0x804792E6 | umac data2
> > > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > > iwlwifi 0000:01:00.0: 0x0006488D | frame pointer
> > > iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> > > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > > iwlwifi 0000:01:00.0: IML/ROM dump:
> > > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > > iwlwifi 0000:01:00.0: 0x000080F3 | IML/ROM data1
> > > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > > iwlwifi 0000:01:00.0: Fseq Registers:
> > > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > > iwlwifi 0000:01:00.0: retry init count 2
> >
> > --
> > Florian
I tried exactly this combination of firmware and PNVM versions on a couple of (Intel based) machines
that I have and the driver loads ok. It can point to some PCIe related issue indeed. I see we already
have a related bug, that probably covers a bunch of different issues with similar behavior. Maybe you can
try the suggestion from the last comment https://bugzilla.kernel.org/show_bug.cgi?id=212371#c34?
If you will be able to enable IOMMU, it'd be possible to get a firmware debug dump that can shed some
light on what's going on there.
Gregory.
On 2022-10-31T08:49:33.000+00:00, Greenman Gregory <[email protected]> wrote:
> On Wed, 2022-10-26 at 20:11 +0200, Florian Schmidt wrote:
>
> > On 2022-10-26T18:47:20.000+01:00, Florian Fainelli <[email protected]> wrote:
> >
> >
> > > On 10/26/22 10:37, Florian Schmidt wrote:
> > >
> > >
> > > > On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> > > >
> > > >
> > > >
> > > > > On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> > > > >
> > > > >
> > > > >
> > > > > > Hi Gregory,
> > > > > >
> > > > > > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> > > > > >
> > > > > >
> > > > > >
> > > > > > > md5sum /lib/firmware/*
> > > > > > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > > > > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > > > > > 33d13d236512466e71c81257209a356f ./regulatory.db
> > > > > >
> > > > > > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> > > > > >
> > > > > > Any other ideas to solve this are welcome.
> > > > >
> > > > > The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> > > > > which you do seem to have based upon the listing above?
> > > > > --
> > > > > Florian
> > > >
> > > > Hi Florian,
> > > >
> > > > Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with
> > > > many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The
> > > > suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
> > > >
> > > > Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
> > > >
> > > > I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
> > >
> > > I am not familiar with ax210, but have worked quite a bit with the 7260
> > > chips (iwlwifi) and errors like those typically occurred when the PCIe
> > > end-point device, that is the ax210 is not able to do PCIe inbound
> > > accesses into your system's memory. Now in your case it could be that
> > > the inaility to load the appropriate ucode results in ... you guessed
> > > it, the ucode not being loaded which causes the timeout to happen.
> > >
> > > Can you tell us more about your ARM32 system here? What PCIe host
> > > bridge/controller does it use, do you have an IOMMU attached to that
> > > PCIe host brideg somehow?
> > >
> > > Thanks!
> > >
> >
> > We're using a Xilinx FPGA Based PCIe root complex on a custom zynq-700 board. The doc of the PCIe block can be found here:
> > https://www.xilinx.com/content/dam/xilinx/support/documents/ip_documentation/axi_pcie/v2_8/pg055-axi-bridge-pcie.pdf
> >
> > I'm not really familiar with IOMMU (or PCIexpress) but to my knowledge there is no support of IOMMU on our arm32 platform, at least I couldn't enable it in kernel options, it required some other
> > platform flags.
> >
> > You can find everything lspci has to say about our device below.
> >
> > root@BV1-27109:~# lspci -vv
> > 00:00.0 PCI bridge: Xilinx Corporation Device 7121 (prog-if 00 [Normal decode])
> > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Latency: 0, Cache Line Size: 64 bytes
> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > I/O behind bridge: 00000000-00000fff [size=4K]
> > Memory behind bridge: 00000000-000fffff [size=1M]
> > Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
> > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- <SERR- <PERR-
> > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- Reset- FastB2B-
> > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > Capabilities: [40] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [48] MSI: Enable- Count=1/32 Maskable+ 64bit+
> > Address: 0000000000000000 Data: 0000
> > Masking: 00000000 Pending: 00000000
> > Capabilities: [60] Express (v2) Root Port (Slot+), MSI 00
> > DevCap: MaxPayload 256 bytes, PhantFunc 1
> > ExtTag+ RBE+
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
> > LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
> > ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > LnkSta: Speed 5GT/s (ok), Width x1 (ok)
> > TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt+
> > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> > Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
> > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> > Control: AttnInd Off, PwrInd Off, Power- Interlock-
> > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> > Changed: MRL- PresDet- LinkState-
> > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> > RootCap: CRSVisible-
> > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
> > AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> > AtomicOpsCtl: ReqEn- EgressBlck-
> > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> > Compliance De-emphasis: -6dB
> > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> > Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
> > Capabilities: [128 v1] Vendor Specific Information: ID=0001 Rev=0 Len=038 <?>
> > Capabilities: [200 v1] Vendor Specific Information: ID=0002 Rev=0 Len=038 <?>
> >
> > 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> > Subsystem: Intel Corporation Device 0020
> > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Interrupt: pin A routed to IRQ 52
> > Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
> > Capabilities: [c8] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
> > Address: 0000000001374000 Data: 0000
> > Capabilities: [40] Express (v2) Endpoint, MSI 00
> > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
> > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag- PhantFunc- On Wed, 2022-10-26 at 20:11 +0200, Florian Schmidt wrote:
> > On 2022-10-26T18:47:20.000+01:00, Florian Fainelli <[email protected]> wrote:
> >
> >
> > > On 10/26/22 10:37, Florian Schmidt wrote:
> > >
> > >
> > > > On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> > > >
> > > >
> > > >
> > > > > On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> > > > >
> > > > >
> > > > >
> > > > > > Hi Gregory,
> > > > > >
> > > > > > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> > > > > >
> > > > > >
> > > > > >
> > > > > > > md5sum /lib/firmware/*
> > > > > > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > > > > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > > > > > 33d13d236512466e71c81257209a356f ./regulatory.db
> > > > > >
> > > > > > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> > > > > >
> > > > > > Any other ideas to solve this are welcome.
> > > > >
> > > > > The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> > > > > which you do seem to have based upon the listing above?
> > > > > --
> > > > > Florian
> > > >
> > > > Hi Florian,
> > > >
> > > > Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with
> > > > many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The
> > > > suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
> > > >
> > > > Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
> > > >
> > > > I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
> > >
> > > I am not familiar with ax210, but have worked quite a bit with the 7260
> > > chips (iwlwifi) and errors like those typically occurred when the PCIe
> > > end-point device, that is the ax210 is not able to do PCIe inbound
> > > accesses into your system's memory. Now in your case it could be that
> > > the inaility to load the appropriate ucode results in ... you guessed
> > > it, the ucode not being loaded which causes the timeout to happen.
> > >
> > > Can you tell us more about your ARM32 system here? What PCIe host
> > > bridge/controller does it use, do you have an IOMMU attached to that
> > > PCIe host brideg somehow?
> > >
> > > Thanks!
> > >
> >
> > We're using a Xilinx FPGA Based PCIe root complex on a custom zynq-700 board. The doc of the PCIe block can be found here:
> > https://www.xilinx.com/content/dam/xilinx/support/documents/ip_documentation/axi_pcie/v2_8/pg055-axi-bridge-pcie.pdf
> >
> > I'm not really familiar with IOMMU (or PCIexpress) but to my knowledge there is no support of IOMMU on our arm32 platform, at least I couldn't enable it in kernel options, it required some other
> > platform flags.
> >
> > You can find everything lspci has to say about our device below.
> >
> > root@BV1-27109:~# lspci -vv
> > 00:00.0 PCI bridge: Xilinx Corporation Device 7121 (prog-if 00 [Normal decode])
> > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Latency: 0, Cache Line Size: 64 bytes
> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > I/O behind bridge: 00000000-00000fff [size=4K]
> > Memory behind bridge: 00000000-000fffff [size=1M]
> > Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
> > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- <SERR- <PERR-
> > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- Reset- FastB2B-
> > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > Capabilities: [40] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [48] MSI: Enable- Count=1/32 Maskable+ 64bit+
> > Address: 0000000000000000 Data: 0000
> > Masking: 00000000 Pending: 00000000
> > Capabilities: [60] Express (v2) Root Port (Slot+), MSI 00
> > DevCap: MaxPayload 256 bytes, PhantFunc 1
> > ExtTag+ RBE+
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
> > LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
> > ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > LnkSta: Speed 5GT/s (ok), Width x1 (ok)
> > TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt+
> > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> > Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
> > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> > Control: AttnInd Off, PwrInd Off, Power- Interlock-
> > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> > Changed: MRL- PresDet- LinkState-
> > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> > RootCap: CRSVisible-
> > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
> > AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> > AtomicOpsCtl: ReqEn- EgressBlck-
> > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> > Compliance De-emphasis: -6dB
> > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> > Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
> > Capabilities: [128 v1] Vendor Specific Information: ID=0001 Rev=0 Len=038 <?>
> > Capabilities: [200 v1] Vendor Specific Information: ID=0002 Rev=0 Len=038 <?>
> >
> > 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> > Subsystem: Intel Corporation Device 0020
> > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Interrupt: pin A routed to IRQ 52
> > Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
> > Capabilities: [c8] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
> > Address: 0000000001374000 Data: 0000
> > Capabilities: [40] Express (v2) Endpoint, MSI 00
> > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
> > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag- PhantFunc- On Wed, 2022-10-26 at 20:11 +0200, Florian Schmidt wrote:
> > On 2022-10-26T18:47:20.000+01:00, Florian Fainelli <[email protected]> wrote:
> >
> >
> > > On 10/26/22 10:37, Florian Schmidt wrote:
> > >
> > >
> > > > On 2022-10-26T18:04:33.000+01:00, Florian Fainelli <[email protected]> wrote:
> > > >
> > > >
> > > >
> > > > > On 10/26/2022 8:56 AM, Florian Schmidt wrote:
> > > > >
> > > > >
> > > > >
> > > > > > Hi Gregory,
> > > > > >
> > > > > > Thank you for having a look at this. The .pnvm file was present in my test as shown by my original message:
> > > > > >
> > > > > >
> > > > > >
> > > > > > > md5sum /lib/firmware/*
> > > > > > > 787381c60d907f81a3ddadc5c990a82b ./iwlwifi-ty-a0-gf-a0-71.ucode
> > > > > > > d93cbdcc4bb5be69aac128e2fe291359 ./iwlwifi-ty-a0-gf-a0.pnvm
> > > > > > > 33d13d236512466e71c81257209a356f ./regulatory.db
> > > > > >
> > > > > > I just ran the test again, ensuring I have the .pnvm you mention and the result is indeed the same.
> > > > > >
> > > > > > Any other ideas to solve this are welcome.
> > > > >
> > > > > The driver indicated it wanted to load iwlwifi-ty-a0-gf-a0-72.ucode,
> > > > > which you do seem to have based upon the listing above?
> > > > > --
> > > > > Florian
> > > >
> > > > Hi Florian,
> > > >
> > > > Indeed, my first log seems to load -72.ucode when my dump show a -71 file, that's strange. I must have mismatched some test, sorry for the confusion. During my tests, I've actually tried with
> > > > many different firmwares (I think I've done all the compatible firmware I could find), tested both with and without the pnvm file and many kernel versions, it always seems to fail. The
> > > > suspicious thing to me is that during my tests, I've confirmed several times that the same sets of wifi card, kernel and firmware work well on my intel desktop.
> > > >
> > > > Below are the logs from my latest test today with firmware -71 and the .pnvm from git.
> > > >
> > > > I'd be happy to help debug more, but I have zero visibility on the firmware so those register dumps just mean nothing to me. Let me know how I can assist with this.
> > >
> > > I am not familiar with ax210, but have worked quite a bit with the 7260
> > > chips (iwlwifi) and errors like those typically occurred when the PCIe
> > > end-point device, that is the ax210 is not able to do PCIe inbound
> > > accesses into your system's memory. Now in your case it could be that
> > > the inaility to load the appropriate ucode results in ... you guessed
> > > it, the ucode not being loaded which causes the timeout to happen.
> > >
> > > Can you tell us more about your ARM32 system here? What PCIe host
> > > bridge/controller does it use, do you have an IOMMU attached to that
> > > PCIe host brideg somehow?
> > >
> > > Thanks!
> > >
> >
> > We're using a Xilinx FPGA Based PCIe root complex on a custom zynq-700 board. The doc of the PCIe block can be found here:
> > https://www.xilinx.com/content/dam/xilinx/support/documents/ip_documentation/axi_pcie/v2_8/pg055-axi-bridge-pcie.pdf
> >
> > I'm not really familiar with IOMMU (or PCIexpress) but to my knowledge there is no support of IOMMU on our arm32 platform, at least I couldn't enable it in kernel options, it required some other
> > platform flags.
> >
> > You can find everything lspci has to say about our device below.
> >
> > root@BV1-27109:~# lspci -vv
> > 00:00.0 PCI bridge: Xilinx Corporation Device 7121 (prog-if 00 [Normal decode])
> > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Latency: 0, Cache Line Size: 64 bytes
> > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> > I/O behind bridge: 00000000-00000fff [size=4K]
> > Memory behind bridge: 00000000-000fffff [size=1M]
> > Prefetchable memory behind bridge: 00000000-000fffff [size=1M]
> > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- <SERR- <PERR-
> > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- Reset- FastB2B-
> > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > Capabilities: [40] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [48] MSI: Enable- Count=1/32 Maskable+ 64bit+
> > Address: 0000000000000000 Data: 0000
> > Masking: 00000000 Pending: 00000000
> > Capabilities: [60] Express (v2) Root Port (Slot+), MSI 00
> > DevCap: MaxPayload 256 bytes, PhantFunc 1
> > ExtTag+ RBE+
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
> > LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
> > ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > LnkSta: Speed 5GT/s (ok), Width x1 (ok)
> > TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt+
> > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> > Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
> > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> > Control: AttnInd Off, PwrInd Off, Power- Interlock-
> > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> > Changed: MRL- PresDet- LinkState-
> > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> > RootCap: CRSVisible-
> > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
> > AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> > AtomicOpsCtl: ReqEn- EgressBlck-
> > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> > Compliance De-emphasis: -6dB
> > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> > Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
> > Capabilities: [128 v1] Vendor Specific Information: ID=0001 Rev=0 Len=038 <?>
> > Capabilities: [200 v1] Vendor Specific Information: ID=0002 Rev=0 Len=038 <?>
> >
> > 01:00.0 Network controller: Intel Corporation Device 2725 (rev 1a)
> > Subsystem: Intel Corporation Device 0020
> > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- <TAbort- <MAbort- SERR- <PERR- INTx-
> > Interrupt: pin A routed to IRQ 52
> > Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=16K]
> > Capabilities: [c8] Power Management version 3
> > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
> > Address: 0000000001374000 Data: 0000
> > Capabilities: [40] Express (v2) Endpoint, MSI 00
> > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
> > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
> > DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> > RlxdOrd+ ExtTag- PhantFunc-0000:01:00.0: 0x804792E6 | umac data2
> >
> > >
> > > > iwlwifi 0000:01:00.0: 0x00000000 | umac data3
> > > > iwlwifi 0000:01:00.0: 0x00000047 | umac major
> > > > iwlwifi 0000:01:00.0: 0x058653F6 | umac minor
> > > > iwlwifi 0000:01:00.0: 0x0006488D | frame pointer
> > > > iwlwifi 0000:01:00.0: 0xC0886244 | stack pointer
> > > > iwlwifi 0000:01:00.0: 0x00000000 | last host cmd
> > > > iwlwifi 0000:01:00.0: 0x00000400 | isr status reg
> > > > iwlwifi 0000:01:00.0: IML/ROM dump:
> > > > iwlwifi 0000:01:00.0: 0x00000B03 | IML/ROM error/state
> > > > iwlwifi 0000:01:00.0: 0x000080F3 | IML/ROM data1
> > > > iwlwifi 0000:01:00.0: 0x00000080 | IML/ROM WFPM_AUTH_KEY_0
> > > > iwlwifi 0000:01:00.0: Fseq Registers:
> > > > iwlwifi 0000:01:00.0: 0x60000000 | FSEQ_ERROR_CODE
> > > > iwlwifi 0000:01:00.0: 0x80440005 | FSEQ_TOP_INIT_VERSION
> > > > iwlwifi 0000:01:00.0: 0x00080009 | FSEQ_CNVIO_INIT_VERSION
> > > > iwlwifi 0000:01:00.0: 0x0000A652 | FSEQ_OTP_VERSION
> > > > iwlwifi 0000:01:00.0: 0x00000002 | FSEQ_TOP_CONTENT_VERSION
> > > > iwlwifi 0000:01:00.0: 0x4552414E | FSEQ_ALIVE_TOKEN
> > > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVI_ID
> > > > iwlwifi 0000:01:00.0: 0x00400410 | FSEQ_CNVR_ID
> > > > iwlwifi 0000:01:00.0: 0x00400410 | CNVI_AUX_MISC_CHIP
> > > > iwlwifi 0000:01:00.0: 0x00400410 | CNVR_AUX_MISC_CHIP
> > > > iwlwifi 0000:01:00.0: 0x00009061 | CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM
> > > > iwlwifi 0000:01:00.0: 0x00000061 | CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR
> > > > iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
> > > > iwlwifi 0000:01:00.0: retry init count 2
> > >
> > > --
> > > Florian
> >
> > I tried exactly this combination of firmware and PNVM versions on a couple of (Intel based) machines
> > that I have and the driver loads ok. It can point to some PCIe related issue indeed. I see we already
> > have a related bug, that probably covers a bunch of different issues with similar behavior. Maybe you can
> > try the suggestion from the last comment https://bugzilla.kernel.org/show_bug.cgi?id=212371#c34?
> > If you will be able to enable IOMMU, it'd be possible to get a firmware debug dump that can shed some
> > light on what's going on there.
> >
> > Gregory.
>
Hi Gregory,
Regarding the bugzilla comment, I can't remove "pci=nomsi,noaer" from bootargs. They're were never there (my bootarg are "console=ttyPS0,921600 earlyprintk uio_pdrv_genirq.of_id=generic-uio").
Kernel config PCIAER is enabled. The listing above from lspci -v seems to indicate that MSI is working properly, it enabled one vector for the ax210. This all indicate I should be in the suggested configuration.
Unfortunately, this hardware (Xilinx Zynq-7000) has no IOMMU support.
I've also tried the same kernel/firmware/pnvm on x64 and x32 intel computers without issue.
On which level of PCIe do you think the issue would be? I could get access access to a serialtek pcie analyzer if this kind of low level trace could be of any help investigating the issue.
Thank you for taking time to help with this,
Florian