I am trying to use the DMA on the ide drives. After the reboot Dma is
enabled but if I don't disable it with hdparm the system freezes at heavy
work (copy something from a drive to the other). The SCSI works ok. Without
the DMA the system barely moves
root@light:~# hdparm -t -T /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 4.83 seconds = 26.50 MB/sec
Timing buffered disk reads: 64 MB in 81.21 seconds =806.99 kB/sec
Any ideas what's wrong?
dmesg:
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
keyboard: Timeout - AT keyboard not present?
keyboard: Timeout - AT keyboard not present?
ServerWorks OSB4: chipset revision 0
ServerWorks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD200EB-00BHF0, ATA DISK drive
hdb: Compaq CRD-8402B, ATAPI CD/DVD-ROM drive
hdc: QUANTUM FIREBALLP AS40.0, ATA DISK drive
hdd: QUANTUM FIREBALLP AS40.0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2586/240/63, UDMA(33)
hdc: 80315072 sectors (41121 MB) w/1902KiB Cache, CHS=79677/16/63, UDMA(33)
hdd: 80315072 sectors (41121 MB) w/1902KiB Cache, CHS=79677/16/63, UDMA(33)
hdb: ATAPI 40X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 1, device 4, function 0
sym53c8xx: 53c896 detected
PCI: Enabling device 01:04.1 (0154 -> 0157)
sym53c8xx: at PCI bus 1, device 4, function 1
sym53c8xx: 53c896 detected
sym53c896-0: rev 0x7 on pci bus 1 device 4 function 0 irq 16
sym53c896-0: ID 7, Fast-40, Parity Checking
sym53c896-0: handling phase mismatch from SCRIPTS.
sym53c896-1: rev 0x7 on pci bus 1 device 4 function 1 irq 16
sym53c896-1: ID 7, Fast-40, Parity Checking
sym53c896-1: handling phase mismatch from SCRIPTS.
scsi0 : sym53c8xx-1.7.3a-20010304
scsi1 : sym53c8xx-1.7.3a-20010304
Vendor: COMPAQ Model: BD0186349B Rev: 3B12
Type: Direct-Access ANSI SCSI revision: 02
Vendor: COMPAQ Model: BD0186349B Rev: 3B12
Type: Direct-Access ANSI SCSI revision: 02
Vendor: COMPAQ Model: BD0186349B Rev: 3B12
Type: Direct-Access ANSI SCSI revision: 02
Vendor: COMPAQ Model: BD0186349B Rev: 3B12
Type: Direct-Access ANSI SCSI revision: 02
ncr53c8xx: at PCI bus 1, device 4, function 0
ncr53c8xx: IO region 0x2000[0..127] is in use
ncr53c8xx: at PCI bus 1, device 4, function 1
ncr53c8xx: IO region 0x2400[0..127] is in use
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0
.config:
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_CMD640_ENHANCED=y
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_PCI_WIP=y
CONFIG_IDEDMA_NEW_DRIVE_LISTINGS=y
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_AEC62XX_TUNING=y
CONFIG_BLK_DEV_ALI15X3=y
CONFIG_WDC_ALI15X3=y
CONFIG_BLK_DEV_AMD7409=y
CONFIG_AMD7409_OVERRIDE=y
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_CY82C693=y
CONFIG_BLK_DEV_CS5530=y
CONFIG_BLK_DEV_HPT34X=y
CONFIG_HPT34X_AUTODMA=y
CONFIG_BLK_DEV_HPT366=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_PIIX_TUNING=y
CONFIG_BLK_DEV_NS87415=y
CONFIG_BLK_DEV_OPTI621=y
CONFIG_BLK_DEV_PDC202XX=y
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_OSB4=y
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
CONFIG_BLK_DEV_TRM290=y
CONFIG_BLK_DEV_VIA82CXXX=y
CONFIG_IDE_CHIPSETS=y
CONFIG_BLK_DEV_4DRIVES=y
CONFIG_BLK_DEV_ALI14XX=y
CONFIG_BLK_DEV_DTC2278=y
CONFIG_BLK_DEV_HT6560B=y
CONFIG_BLK_DEV_PDC4030=y
CONFIG_BLK_DEV_QD6580=y
CONFIG_BLK_DEV_UMC8672=y
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_IVB=y
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
#
# SCSI support
#
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
Thanks,
axl
2.4.4-p1 is the kernel version that i've tried now. no succes with 2.4.3 and
below.
i've been trying without the CDROM and a normal HDD ata 66. i've made some
progress using the normal ide ata 66 driver and removing the osv4 from
kernel.
root@light:/# hdparm -t -T /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.81 seconds =158.02 MB/sec
Timing buffered disk reads: MB in 8.41 seconds = 7.61 MB/sec
root@light:/# hdparm -v /dev/hda
/dev/hda:
multcount = 16 (on)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 2586/240/63, sectors = 39102336, start = 0
still my bios is set to enhaced DMA. i am still working on UDMA. if u have
any suggestions i still wait for a solution.
axl
----- Original Message -----
From: "Mark Hahn" <[email protected]>
To: "Alexandru Barloiu Nicolae" <[email protected]>
Sent: Tuesday, April 10, 2001 1:39 AM
Subject: Re: Compaq proliant ML-350 - IDE & SCSI
> > ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
>
> ugh. not a widely-respected implementation. I don't think you mentioned
> which kernel you're runnint, either, since there have been several
successive
> generations of workarounds for SW ide/etc stuff.
>
> > hda: WDC WD200EB-00BHF0, ATA DISK drive
> > hdb: Compaq CRD-8402B, ATAPI CD/DVD-ROM drive
>
> sharing a channel like this is not a good idea. you should definitely
> test without the cdrom drive. all your ide cables are 18" or less?
>
> 2.4.4-p1 is the kernel version that i've tried now. no succes with 2.4.3 and
> below.
Please see if the 2.4.3-ac version of osb4 works on your box. I need to get
more results on this to know if I got it right
----- Original Message -----
From: "Alan Cox" <[email protected]>
To: "Alexandru Barloiu Nicolae" <[email protected]>
Cc: "Mark Hahn" <[email protected]>;
<[email protected]>
Sent: Tuesday, April 10, 2001 1:00 PM
Subject: Re: Compaq proliant ML-350 - IDE & SCSI
> > 2.4.4-p1 is the kernel version that i've tried now. no succes with 2.4.3
and
> > below.
>
> Please see if the 2.4.3-ac version of osb4 works on your box. I need to
get
> more results on this to know if I got it right
>
Still hangs. No ops no nothing. Just hangs. I've got 8 ext2fs in this system
and it takes foresever to start. :(
axl