From: dillon min <[email protected]>
This patchset intend to add art-pi board support, this board developed
by rt-thread(https://www.rt-thread.org/).
Board resources:
8MiB QSPI flash
16MiB SPI flash
32MiB SDRAM
AP6212 wifi,bt,fm comb
sw context:
- as stm32h750 just has 128k bytes internal flash, so running a fw on
internal flash to download u-boot/kernel to qspi flash, boot
u-boot/kernel from qspi flash. this fw is based on rt-thread.
- kernel can be xip on qspi flash or load to sdram
- root filesystem is jffs2(created by buildroot), stored on spi flash
to support the boad, add following changes.
- fix r0-r3, r12 register restore failed after svc call,
- add dts binding
- update yaml doc
---
changes in v5:
- accroding to rob's suggestion, replace false with 'type: object'
of 'additionalProperties'.
- add Tested-by: Valentin Caron <[email protected]>
changes in v4:
- use unevaluatedProperties: false to fix dtbs_check warrnings instead of
add 'bluetooth' in st,stm32-uart.yaml
changes in v3:
- fix dtbs_check warrning: (8002cbd78fd5 and 4bc21d3dd678)
>> arch/arm/boot/dts/stm32h743i-eval.dt.yaml: soc: pin-controller:
{'type': 'object'} is not allowed for {'#address-cells': [[1]], '#size-cells':
[[1]], 'ranges': [[0,
>> arch/arm/boot/dts/stm32h743i-eval.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes: '@(0|[1-9a-f][0-9a-f]*)$',
'^[^@]+$', 'pinctrl-[0-9]+'
>> arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
changes in v2:
- reorganize the pinctrl device tree about
stm32h7-pinctrl/stm32h743/750-pinctrl
stm32h7-pinctrl.dtsi --> stm32h743-pinctrl.dtsi --> stm32h743i-disco.dts
| |-> stm32h743i-eval.dts
|-> stm32h750-pinctrl.dtsi --> stm32h750i-art-pi.dts
same to the stm32f7/f4's pinctrl style
- fix author name/copyright mistake
- add compatible string st,stm32h750-pinctrl to pinctl-stm32h743.c as they
have same pin alternate functions, update Kconfig description
- make item in stm32h750i-art-pi.dts sort by letter
*** BLURB HERE ***
dillon min (9):
Documentation: arm: stm32: Add stm32h750 value line doc
dt-bindings: arm: stm32: Add compatible strings for ART-PI board
dt-bindings: pinctrl: stm32: Add stm32h750 pinctrl
ARM: dts: stm32: introduce stm32h7-pinctrl.dtsi to support stm32h750
ARM: dts: stm32: add stm32h750-pinctrl.dtsi
ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
ARM: stm32: Add a new SOC - STM32H750
pinctrl: stm32: Add STM32H750 MCU pinctrl support
dt-bindings: serial: stm32: Use 'type: object' instead of false for
'additionalProperties'
Documentation/arm/index.rst | 1 +
Documentation/arm/stm32/stm32h750-overview.rst | 34 +++
.../devicetree/bindings/arm/stm32/stm32.yaml | 4 +
.../bindings/pinctrl/st,stm32-pinctrl.yaml | 1 +
.../devicetree/bindings/serial/st,stm32-uart.yaml | 3 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/stm32h7-pinctrl.dtsi | 274 ++++++++++++++++++
arch/arm/boot/dts/stm32h743-pinctrl.dtsi | 307 +--------------------
arch/arm/boot/dts/stm32h743.dtsi | 153 +++++++++-
arch/arm/boot/dts/stm32h750-pinctrl.dtsi | 12 +
arch/arm/boot/dts/stm32h750.dtsi | 6 +
arch/arm/boot/dts/stm32h750i-art-pi.dts | 229 +++++++++++++++
arch/arm/mach-stm32/board-dt.c | 1 +
drivers/pinctrl/stm32/Kconfig | 2 +-
drivers/pinctrl/stm32/pinctrl-stm32h743.c | 3 +
15 files changed, 726 insertions(+), 305 deletions(-)
create mode 100644 Documentation/arm/stm32/stm32h750-overview.rst
create mode 100644 arch/arm/boot/dts/stm32h7-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/stm32h750-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
--
2.7.4
From: dillon min <[email protected]>
This patchset add support for soc stm32h750, stm32h750 has mirror
different from stm32h743
item stm32h743 stm32h750
flash size: 2MiB 128KiB
adc: none 3
crypto-hash: none aes/hamc/des/tdes/md5/sha
detail information can be found at:
https://www.st.com/en/microcontrollers-microprocessors/stm32h750-value-line.html
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
Documentation/arm/index.rst | 1 +
Documentation/arm/stm32/stm32h750-overview.rst | 34 ++++++++++++++++++++++++++
2 files changed, 35 insertions(+)
create mode 100644 Documentation/arm/stm32/stm32h750-overview.rst
diff --git a/Documentation/arm/index.rst b/Documentation/arm/index.rst
index b4bea32472b6..d4f34ae9e6f4 100644
--- a/Documentation/arm/index.rst
+++ b/Documentation/arm/index.rst
@@ -52,6 +52,7 @@ SoC-specific documents
stm32/stm32f746-overview
stm32/overview
stm32/stm32h743-overview
+ stm32/stm32h750-overview
stm32/stm32f769-overview
stm32/stm32f429-overview
stm32/stm32mp157-overview
diff --git a/Documentation/arm/stm32/stm32h750-overview.rst b/Documentation/arm/stm32/stm32h750-overview.rst
new file mode 100644
index 000000000000..0e51235c9547
--- /dev/null
+++ b/Documentation/arm/stm32/stm32h750-overview.rst
@@ -0,0 +1,34 @@
+==================
+STM32H750 Overview
+==================
+
+Introduction
+------------
+
+The STM32H750 is a Cortex-M7 MCU aimed at various applications.
+It features:
+
+- Cortex-M7 core running up to @480MHz
+- 128K internal flash, 1MBytes internal RAM
+- FMC controller to connect SDRAM, NOR and NAND memories
+- Dual mode QSPI
+- SD/MMC/SDIO support
+- Ethernet controller
+- USB OTFG FS & HS controllers
+- I2C, SPI, CAN busses support
+- Several 16 & 32 bits general purpose timers
+- Serial Audio interface
+- LCD controller
+- HDMI-CEC
+- SPDIFRX
+- DFSDM
+
+Resources
+---------
+
+Datasheet and reference manual are publicly available on ST website (STM32H750_).
+
+.. _STM32H750: https://www.st.com/en/microcontrollers-microprocessors/stm32h750-value-line.html
+
+:Authors: Dillon Min <[email protected]>
+
--
2.7.4
From: dillon min <[email protected]>
This patch is intend to add support stm32h750 value line,
just add stm32h7-pinctrl.dtsi for extending, with following changes:
- rename stm32h743-pinctrl.dtsi to stm32h7-pinctrl.dtsi
- move compatible string "st,stm32h743-pinctrl" from stm32h7-pinctrl.dtsi
to stm32h743-pinctrl.dtsi
- move 'pin-controller' from stm32h7-pinctrl.dtsi to stm32h743.dtsi, to
fix make dtbs_check warrnings
arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes:
'@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
arch/arm/boot/dts/stm32h7-pinctrl.dtsi | 274 +++++++++++++++++++++++++++
arch/arm/boot/dts/stm32h743-pinctrl.dtsi | 307 +------------------------------
2 files changed, 280 insertions(+), 301 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32h7-pinctrl.dtsi
diff --git a/arch/arm/boot/dts/stm32h7-pinctrl.dtsi b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi
new file mode 100644
index 000000000000..fbab41a01af5
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi
@@ -0,0 +1,274 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+ i2c1_pins_a: i2c1-0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
+ <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+ };
+ };
+
+ ethernet_rmii: rmii-0 {
+ pins {
+ pinmux = <STM32_PINMUX('G', 11, AF11)>,
+ <STM32_PINMUX('G', 13, AF11)>,
+ <STM32_PINMUX('G', 12, AF11)>,
+ <STM32_PINMUX('C', 4, AF11)>,
+ <STM32_PINMUX('C', 5, AF11)>,
+ <STM32_PINMUX('A', 7, AF11)>,
+ <STM32_PINMUX('C', 1, AF11)>,
+ <STM32_PINMUX('A', 2, AF11)>,
+ <STM32_PINMUX('A', 1, AF11)>;
+ slew-rate = <2>;
+ };
+ };
+
+ sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+ };
+ };
+
+ sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+ <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */
+ };
+ };
+
+ sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
+ bias-pull-up;
+ };
+ };
+
+ sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
+ };
+ };
+
+ usart1_pins: usart1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
+ bias-disable;
+ };
+ };
+
+ usart2_pins: usart2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+ bias-disable;
+ };
+ };
+
+ usart3_pins: usart3-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+ <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+ <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ uart4_pins: uart4-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */
+ bias-disable;
+ };
+ };
+
+ usbotg_hs_pins_a: usbotg-hs-0 {
+ pins {
+ pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */
+ <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
+ <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */
+ <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */
+ <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */
+ <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */
+ <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */
+ <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
+ <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
+ <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
+ <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
+ <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ };
+
+ spi1_pins: spi1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('A', 5, AF5)>,
+ /* SPI1_CLK */
+ <STM32_PINMUX('B', 5, AF5)>;
+ /* SPI1_MOSI */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('G', 9, AF5)>;
+ /* SPI1_MISO */
+ bias-disable;
+ };
+ };
+};
+
diff --git a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
index fa5dcb6a5fdd..6b1e115307b9 100644
--- a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi
@@ -1,306 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
- * Copyright 2017 - Alexandre Torgue <[email protected]>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue <[email protected]> for STMicroelectronics.
*/
-#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+#include "stm32h7-pinctrl.dtsi"
-/ {
- soc {
- pin-controller {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,stm32h743-pinctrl";
- ranges = <0 0x58020000 0x3000>;
- interrupt-parent = <&exti>;
- st,syscfg = <&syscfg 0x8>;
- pins-are-numbered;
-
- gpioa: gpio@58020000 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x0 0x400>;
- clocks = <&rcc GPIOA_CK>;
- st,bank-name = "GPIOA";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpiob: gpio@58020400 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x400 0x400>;
- clocks = <&rcc GPIOB_CK>;
- st,bank-name = "GPIOB";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpioc: gpio@58020800 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x800 0x400>;
- clocks = <&rcc GPIOC_CK>;
- st,bank-name = "GPIOC";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpiod: gpio@58020c00 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0xc00 0x400>;
- clocks = <&rcc GPIOD_CK>;
- st,bank-name = "GPIOD";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpioe: gpio@58021000 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x1000 0x400>;
- clocks = <&rcc GPIOE_CK>;
- st,bank-name = "GPIOE";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpiof: gpio@58021400 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x1400 0x400>;
- clocks = <&rcc GPIOF_CK>;
- st,bank-name = "GPIOF";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpiog: gpio@58021800 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x1800 0x400>;
- clocks = <&rcc GPIOG_CK>;
- st,bank-name = "GPIOG";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpioh: gpio@58021c00 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x1c00 0x400>;
- clocks = <&rcc GPIOH_CK>;
- st,bank-name = "GPIOH";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpioi: gpio@58022000 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x2000 0x400>;
- clocks = <&rcc GPIOI_CK>;
- st,bank-name = "GPIOI";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpioj: gpio@58022400 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x2400 0x400>;
- clocks = <&rcc GPIOJ_CK>;
- st,bank-name = "GPIOJ";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpiok: gpio@58022800 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x2800 0x400>;
- clocks = <&rcc GPIOK_CK>;
- st,bank-name = "GPIOK";
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- i2c1_pins_a: i2c1-0 {
- pins {
- pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
- <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
- bias-disable;
- drive-open-drain;
- slew-rate = <0>;
- };
- };
-
- ethernet_rmii: rmii-0 {
- pins {
- pinmux = <STM32_PINMUX('G', 11, AF11)>,
- <STM32_PINMUX('G', 13, AF11)>,
- <STM32_PINMUX('G', 12, AF11)>,
- <STM32_PINMUX('C', 4, AF11)>,
- <STM32_PINMUX('C', 5, AF11)>,
- <STM32_PINMUX('A', 7, AF11)>,
- <STM32_PINMUX('C', 1, AF11)>,
- <STM32_PINMUX('A', 2, AF11)>,
- <STM32_PINMUX('A', 1, AF11)>;
- slew-rate = <2>;
- };
- };
-
- sdmmc1_b4_pins_a: sdmmc1-b4-0 {
- pins {
- pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
- <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
- <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
- <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
- <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
- <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
- slew-rate = <3>;
- drive-push-pull;
- bias-disable;
- };
- };
-
- sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
- pins1 {
- pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
- <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
- <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
- <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
- <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
- slew-rate = <3>;
- drive-push-pull;
- bias-disable;
- };
- pins2{
- pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
- slew-rate = <3>;
- drive-open-drain;
- bias-disable;
- };
- };
-
- sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
- pins {
- pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
- <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
- <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
- <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
- <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
- <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
- };
- };
-
- sdmmc1_dir_pins_a: sdmmc1-dir-0 {
- pins1 {
- pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
- <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
- <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
- slew-rate = <3>;
- drive-push-pull;
- bias-pull-up;
- };
- pins2{
- pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
- bias-pull-up;
- };
- };
-
- sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
- pins {
- pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
- <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
- <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
- <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
- };
- };
-
- usart1_pins: usart1-0 {
- pins1 {
- pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
- bias-disable;
- drive-push-pull;
- slew-rate = <0>;
- };
- pins2 {
- pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
- bias-disable;
- };
- };
-
- usart2_pins: usart2-0 {
- pins1 {
- pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
- bias-disable;
- drive-push-pull;
- slew-rate = <0>;
- };
- pins2 {
- pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
- bias-disable;
- };
- };
-
- usbotg_hs_pins_a: usbotg-hs-0 {
- pins {
- pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */
- <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
- <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */
- <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */
- <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */
- <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */
- <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */
- <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
- <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
- <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
- <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
- <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */
- bias-disable;
- drive-push-pull;
- slew-rate = <2>;
- };
- };
- };
- };
+&pinctrl{
+ compatible = "st,stm32h743-pinctrl";
};
--
2.7.4
From: dillon min <[email protected]>
This patch add stm32h750-pinctrl.dtsi which just
reference stm32h7-pinctrl.dtsi
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
arch/arm/boot/dts/stm32h750-pinctrl.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32h750-pinctrl.dtsi
diff --git a/arch/arm/boot/dts/stm32h750-pinctrl.dtsi b/arch/arm/boot/dts/stm32h750-pinctrl.dtsi
new file mode 100644
index 000000000000..ef8c4d881dba
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750-pinctrl.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Dillon Min <[email protected]> for STMicroelectronics.
+ */
+
+#include "stm32h7-pinctrl.dtsi"
+
+&pinctrl{
+ compatible = "st,stm32h750-pinctrl";
+};
+
--
2.7.4
From: dillon min <[email protected]>
The STM32H750 is a Cortex-M7 MCU running at 480MHz
and containing 128KBytes internal flash, 1MiB SRAM.
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
arch/arm/mach-stm32/board-dt.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-dt.c
index 011d57b488c2..a766310d8dca 100644
--- a/arch/arm/mach-stm32/board-dt.c
+++ b/arch/arm/mach-stm32/board-dt.c
@@ -17,6 +17,7 @@ static const char *const stm32_compat[] __initconst = {
"st,stm32f746",
"st,stm32f769",
"st,stm32h743",
+ "st,stm32h750",
"st,stm32mp157",
NULL
};
--
2.7.4
From: dillon min <[email protected]>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add dts binding usart3 for bt, uart4 for console
usart3/uart4 pinctrl in stm32h7-pinctrl.dtsi
usart3/uart4 register in stm32h743.dtsi
- add dts binding sdmmc2 for wifi
sdmmc2 pinctrl in stm32h7-pinctrl.dtsi
sdmmc2 register in stm32h743.dtsi
- add spi1 pinctrl in stm32h7-pinctrl.dtsi for spi flash
- add stm32h750-art-pi.dts to support art-pi board
- add pinctrl: pin-controller@58020000 {} to fix dtbs_check warrnings
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/stm32h743.dtsi | 153 ++++++++++++++++++++-
arch/arm/boot/dts/stm32h750.dtsi | 6 +
arch/arm/boot/dts/stm32h750i-art-pi.dts | 229 ++++++++++++++++++++++++++++++++
4 files changed, 387 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8e5d4ab4e75e..a19c5ab9df84 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1071,6 +1071,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32746g-eval.dtb \
stm32h743i-eval.dtb \
stm32h743i-disco.dtb \
+ stm32h750i-art-pi.dtb \
stm32mp153c-dhcom-drc02.dtb \
stm32mp157a-avenger96.dtb \
stm32mp157a-dhcor-avenger96.dtb \
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 4ebffb0a45a3..4379063d36a2 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -135,6 +135,22 @@
clocks = <&rcc USART2_CK>;
};
+ usart3: serial@40004800 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40004800 0x400>;
+ interrupts = <39>;
+ status = "disabled";
+ clocks = <&rcc USART3_CK>;
+ };
+
+ uart4: serial@40004c00 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40004c00 0x400>;
+ interrupts = <52>;
+ status = "disabled";
+ clocks = <&rcc UART4_CK>;
+ };
+
i2c1: i2c@40005400 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
@@ -159,7 +175,7 @@
status = "disabled";
};
- i2c3: i2c@40005C00 {
+ i2c3: i2c@40005c00 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
#size-cells = <0>;
@@ -368,6 +384,20 @@
max-frequency = <120000000>;
};
+ sdmmc2: mmc@48022400 {
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x10153180>;
+ reg = <0x48022400 0x400>;
+ interrupts = <124>;
+ interrupt-names = "cmd_irq";
+ clocks = <&rcc SDMMC2_CK>;
+ clock-names = "apb_pclk";
+ resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ };
+
exti: interrupt-controller@58000000 {
compatible = "st,stm32h7-exti";
interrupt-controller;
@@ -392,7 +422,7 @@
status = "disabled";
};
- i2c4: i2c@58001C00 {
+ i2c4: i2c@58001c00 {
compatible = "st,stm32f7-i2c";
#address-cells = <1>;
#size-cells = <0>;
@@ -555,6 +585,125 @@
snps,pbl = <8>;
status = "disabled";
};
+
+ pinctrl: pin-controller@58020000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x58020000 0x3000>;
+ interrupt-parent = <&exti>;
+ st,syscfg = <&syscfg 0x8>;
+ pins-are-numbered;
+
+ gpioa: gpio@58020000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x0 0x400>;
+ clocks = <&rcc GPIOA_CK>;
+ st,bank-name = "GPIOA";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiob: gpio@58020400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x400 0x400>;
+ clocks = <&rcc GPIOB_CK>;
+ st,bank-name = "GPIOB";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioc: gpio@58020800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x800 0x400>;
+ clocks = <&rcc GPIOC_CK>;
+ st,bank-name = "GPIOC";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiod: gpio@58020c00 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0xc00 0x400>;
+ clocks = <&rcc GPIOD_CK>;
+ st,bank-name = "GPIOD";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioe: gpio@58021000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1000 0x400>;
+ clocks = <&rcc GPIOE_CK>;
+ st,bank-name = "GPIOE";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiof: gpio@58021400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1400 0x400>;
+ clocks = <&rcc GPIOF_CK>;
+ st,bank-name = "GPIOF";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiog: gpio@58021800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1800 0x400>;
+ clocks = <&rcc GPIOG_CK>;
+ st,bank-name = "GPIOG";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioh: gpio@58021c00 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1c00 0x400>;
+ clocks = <&rcc GPIOH_CK>;
+ st,bank-name = "GPIOH";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioi: gpio@58022000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2000 0x400>;
+ clocks = <&rcc GPIOI_CK>;
+ st,bank-name = "GPIOI";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpioj: gpio@58022400 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2400 0x400>;
+ clocks = <&rcc GPIOJ_CK>;
+ st,bank-name = "GPIOJ";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpiok: gpio@58022800 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2800 0x400>;
+ clocks = <&rcc GPIOK_CK>;
+ st,bank-name = "GPIOK";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
new file mode 100644
index 000000000000..41e3b1e3a874
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750.dtsi
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
+
+#include "stm32h743.dtsi"
+
+
diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
new file mode 100644
index 000000000000..098181efd172
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
@@ -0,0 +1,229 @@
+/*
+ * Copyright 2021 - Dillon Min <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * For art-pi board resources, you can refer to link:
+ * https://art-pi.gitee.io/website/
+ */
+
+/dts-v1/;
+#include "stm32h750.dtsi"
+#include "stm32h750-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "RT-Thread STM32H750i-ART-PI board";
+ compatible = "st,stm32h750i-art-pi", "st,stm32h750";
+
+ chosen {
+ bootargs = "root=/dev/ram";
+ stdout-path = "serial0:2000000n8";
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x2000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ no-map;
+ size = <0x100000>;
+ linux,dma-default;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ serial1 = &usart3;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-red {
+ gpios = <&gpioi 8 0>;
+ };
+ led-green {
+ gpios = <&gpioc 15 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ v3v3: regulator-v3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ wlan_pwr: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "wl-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&clk_hse {
+ clock-frequency = <25000000>;
+};
+
+&dma1 {
+ status = "okay";
+};
+
+&dma2 {
+ status = "okay";
+};
+
+&mac {
+ status = "disabled";
+ pinctrl-0 = <ðernet_rmii>;
+ pinctrl-names = "default";
+ phy-mode = "rmii";
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+ broken-cd;
+ non-removable;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&wlan_pwr>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
+ dmas = <&dmamux1 37 0x400 0x05>,
+ <&dmamux1 38 0x400 0x05>;
+ dma-names = "rx", "tx";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+
+ partition@0 {
+ label = "root filesystem";
+ reg = <0 0x1000000>;
+ };
+ };
+};
+
+&usart2 {
+ pinctrl-0 = <&usart2_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+};
+
+&usart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usart3_pins>;
+ dmas = <&dmamux1 45 0x400 0x05>,
+ <&dmamux1 46 0x400 0x05>;
+ dma-names = "rx", "tx";
+ st,hw-flow-ctrl;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+ max-speed = <115200>;
+ };
+};
+
+&uart4 {
+ pinctrl-0 = <&uart4_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+
--
2.7.4
From: dillon min <[email protected]>
This patch adds STM32H750 pinctrl and GPIO support
since stm32h750 has the same pin alternate functions
with stm32h743, so just reuse the stm32h743's pinctrl
driver
Signed-off-by: dillon min <[email protected]>
---
v5: no changes
drivers/pinctrl/stm32/Kconfig | 2 +-
drivers/pinctrl/stm32/pinctrl-stm32h743.c | 3 +++
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/pinctrl/stm32/Kconfig b/drivers/pinctrl/stm32/Kconfig
index f36f29113370..fb1ffc94c57f 100644
--- a/drivers/pinctrl/stm32/Kconfig
+++ b/drivers/pinctrl/stm32/Kconfig
@@ -35,7 +35,7 @@ config PINCTRL_STM32F769
select PINCTRL_STM32
config PINCTRL_STM32H743
- bool "STMicroelectronics STM32H743 pin control" if COMPILE_TEST && !MACH_STM32H743
+ bool "STMicroelectronics STM32H743/STM32H750 pin control" if COMPILE_TEST && !MACH_STM32H743
depends on OF && HAS_IOMEM
default MACH_STM32H743
select PINCTRL_STM32
diff --git a/drivers/pinctrl/stm32/pinctrl-stm32h743.c b/drivers/pinctrl/stm32/pinctrl-stm32h743.c
index ffe7b5271506..700206c7bc11 100644
--- a/drivers/pinctrl/stm32/pinctrl-stm32h743.c
+++ b/drivers/pinctrl/stm32/pinctrl-stm32h743.c
@@ -1966,6 +1966,9 @@ static const struct of_device_id stm32h743_pctrl_match[] = {
.compatible = "st,stm32h743-pinctrl",
.data = &stm32h743_match_data,
},
+ { .compatible = "st,stm32h750-pinctrl",
+ .data = &stm32h743_match_data,
+ },
{ }
};
--
2.7.4
From: dillon min <[email protected]>
To use additional properties 'bluetooth' on serial, need replace false with
'type: object' for 'additionalProperties' to make it as a node, else will
run into dtbs_check warnings.
'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: af1c2d81695b ("dt-bindings: serial: Convert STM32 UART to json-schema")
Reported-by: kernel test robot <[email protected]>
Tested-by: Valentin Caron <[email protected]>
Signed-off-by: dillon min <[email protected]>
---
v5: accroding to rob's suggestion, replace false with 'type: object'
of 'additionalProperties'.
Documentation/devicetree/bindings/serial/st,stm32-uart.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
index 8631678283f9..865be05083c3 100644
--- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
+++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
@@ -80,7 +80,8 @@ required:
- interrupts
- clocks
-additionalProperties: false
+additionalProperties:
+ type: object
examples:
- |
--
2.7.4
Hi Dillon,
It's okay for me.
Regards,
Valentin
On 3/25/21 7:19 AM, [email protected] wrote:
> From: dillon min <[email protected]>
>
> To use additional properties 'bluetooth' on serial, need replace false with
> 'type: object' for 'additionalProperties' to make it as a node, else will
> run into dtbs_check warnings.
>
> 'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
> 'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
>
> Fixes: af1c2d81695b ("dt-bindings: serial: Convert STM32 UART to json-schema")
> Reported-by: kernel test robot <[email protected]>
> Tested-by: Valentin Caron <[email protected]>
> Signed-off-by: dillon min <[email protected]>
> ---
>
> v5: accroding to rob's suggestion, replace false with 'type: object'
> of 'additionalProperties'.
>
> Documentation/devicetree/bindings/serial/st,stm32-uart.yaml | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> index 8631678283f9..865be05083c3 100644
> --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> @@ -80,7 +80,8 @@ required:
> - interrupts
> - clocks
>
> -additionalProperties: false
> +additionalProperties:
> + type: object
>
> examples:
> - |
Hi Valentin
On Thu, Mar 25, 2021 at 7:12 PM Valentin CARON - foss
<[email protected]> wrote:
>
> Hi Dillon,
>
> It's okay for me.
>
> Regards,
>
> Valentin
Thanks for your test, and quick reply.
>
> On 3/25/21 7:19 AM, [email protected] wrote:
> > From: dillon min <[email protected]>
> >
> > To use additional properties 'bluetooth' on serial, need replace false with
> > 'type: object' for 'additionalProperties' to make it as a node, else will
> > run into dtbs_check warnings.
> >
> > 'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
> > 'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
> >
> > Fixes: af1c2d81695b ("dt-bindings: serial: Convert STM32 UART to json-schema")
> > Reported-by: kernel test robot <[email protected]>
> > Tested-by: Valentin Caron <[email protected]>
> > Signed-off-by: dillon min <[email protected]>
> > ---
> >
> > v5: accroding to rob's suggestion, replace false with 'type: object'
> > of 'additionalProperties'.
> >
> > Documentation/devicetree/bindings/serial/st,stm32-uart.yaml | 3 ++-
> > 1 file changed, 2 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> > index 8631678283f9..865be05083c3 100644
> > --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> > +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> > @@ -80,7 +80,8 @@ required:
> > - interrupts
> > - clocks
> >
> > -additionalProperties: false
> > +additionalProperties:
> > + type: object
> >
> > examples:
> > - |