From: Quentin Schulz <[email protected]>
The PX30-uQ7 (Ringneck) SoM is a µQseven-compatible (40mmx70mm, MXM-230
connector) system-on-module from Theobroma Systems[1], featuring the
Rockchip PX30.
It provides the following feature set:
* up to 4GB DDR4
* up to 128GB on-module eMMC (with 8-bit 1.8V interface)
* SD card (on a baseboard) via edge connector
* Fast Ethernet with on-module TI DP83825I PHY
* MIPI-DSI/LVDS
* MIPI-CSI
* USB
- 1x USB 2.0 dual-role
- 3x USB 2.0 host
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
* on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
* on-module NXP SE05x Secure Element
[1] https://www.theobroma-systems.com/som-product/px30-%C2%B5q7/
Signed-off-by: Quentin Schulz <[email protected]>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/px30-ringneck-haikou.dts | 239 ++++++++++++
.../boot/dts/rockchip/px30-ringneck.dtsi | 347 ++++++++++++++++++
3 files changed, 587 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
create mode 100644 arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ef79a672804a..1e3b9d7c1a8b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2-of10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-ringneck-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-s.dtb
diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts b/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
new file mode 100644
index 000000000000..6304d6f7baa3
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "px30-ringneck.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Theobroma Systems PX30-µQ7 SoM on Haikou devkit";
+ compatible = "tsd,px30-ringneck-haikou", "rockchip,px30";
+
+ aliases {
+ mmc2 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys: haikou-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&haikou_keys_pin>;
+ pinctrl-names = "default";
+
+ BATLOWn {
+ label = "BATLOW#";
+ linux,code = <KEY_BATTERY>;
+ gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
+ };
+
+ BIOS_DISABLEn {
+ label = "BIOS_DISABLE#";
+ linux,code = <SW_BOOT_ALT>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+ };
+
+ LID_BTNn {
+ label = "LID_BTN#";
+ linux,code = <SW_LID>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+ };
+
+ SLP_BTNn {
+ label = "SLP_BTN#";
+ linux,code = <KEY_SLEEP>;
+ gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+ };
+
+ WAKEn {
+ label = "WAKE#";
+ linux,code = <KEY_WAKEUP>;
+ gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ pinctrl-0 = <&module_led_pin>, <&sd_card_led_pin>;
+
+ sd_card_led: led-1 {
+ label = "sd_card_led";
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc2";
+ };
+ };
+
+ i2s0-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Haikou,I2S-codec";
+ simple-audio-card,mclk-fs = <512>;
+
+ simple-audio-card,codec {
+ clocks = <&sgtl5000_clk>;
+ sound-dai = <&sgtl5000>;
+ };
+
+ simple-audio-card,cpu {
+ bitclock-master;
+ frame-master;
+ sound-dai = <&i2s0_8ch>;
+ };
+ };
+
+ sgtl5000_clk: sgtl5000-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_baseboard: vcc3v3-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_baseboard: vcc5v0-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vdda_codec: vdda-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vdda_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+
+ vddd_codec: vddd-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vddd_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1600000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sgtl5000_clk>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <&vdda_codec>;
+ VDDIO-supply = <&vcc3v3_baseboard>;
+ VDDD-supply = <&vddd_codec>;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ eeprom@50 {
+ reg = <0x50>;
+ compatible = "atmel,24c01";
+ pagesize = <8>;
+ size = <128>;
+ vcc-supply = <&vcc3v3_baseboard>;
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+};
+
+&pinctrl {
+ haikou {
+ haikou_keys_pin: haikou-keys-pin {
+ rockchip,pins =
+ /* WAKE# */
+ <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* SLP_BTN# */
+ <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* LID_BTN */
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BATLOW# */
+ <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BIOS_DISABLE# */
+ <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ sd_card_led_pin: sd-card-led-pin {
+ rockchip,pins =
+ <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ vmmc-supply = <&vcc3v3_baseboard>;
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-0 = <&uart5_xfer>;
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
new file mode 100644
index 000000000000..74a7f1182c21
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
@@ -0,0 +1,347 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "px30.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &emmc;
+ mmc1 = &sdio;
+ rtc0 = &rtc_twi;
+ rtc1 = &rk809;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio1 RK_PB3 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&module_led_pin>;
+ status = "okay";
+
+ module_led: led-0 {
+ label = "module_led";
+ gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vcc5v0_sys: vccsys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ supports-emmc;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_emmc>;
+
+ status = "okay";
+};
+
+/* On-module TI DP83825I PHY but no connector, enable in carrierboard */
+&gmac {
+ snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 50000 50000>;
+ phy-supply = <&vcc_3v3>;
+ clock_in_out = "output";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&pmic_int>;
+ pinctrl-names = "default";
+ #clock-cells = <0>;
+ clock-output-names = "xin32k";
+ rockchip,system-power-controller;
+ wakeup-source;
+ status = "okay";
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_3v3>;
+ vcc6-supply = <&vcc_3v3>;
+ vcc7-supply = <&vcc_3v3>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v0_1v8: vcc_emmc: DCDC_REG4 {
+ regulator-name = "vcc_3v0_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc_3v3: DCDC_REG5 {
+ regulator-name = "vcc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG2 {
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_1v0: LDO_REG3 {
+ regulator-name = "vcc_1v0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc_lcd: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vcc_lcd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_1v8_lcd: LDO_REG8 {
+ regulator-name = "vcc_1v8_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG9 {
+ regulator-name = "vcca_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ /* SE05x is limited to Fast Mode */
+ clock-frequency = <400000>;
+
+ fan: fan@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ #cooling-cells = <2>;
+ };
+
+ rtc_twi: rtc@6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2s0_8ch {
+ rockchip,trcm-sync-tx-only;
+
+ pinctrl-0 = <&i2s0_8ch_sclktx &i2s0_8ch_lrcktx
+ &i2s0_8ch_sdo0 &i2s0_8ch_sdi0>;
+};
+
+&io_domains {
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_3v3>;
+ vccio4-supply = <&vcc_3v3>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_emmc>;
+ vccio-oscgpi-supply = <&vcc_3v3>;
+
+ status = "okay";
+};
+
+&pinctrl {
+ emmc {
+ emmc_reset: emmc-reset {
+ rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ module_led_pin: module-led-pin {
+ rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+/* Mule UCAN */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
2.37.3
Hi all,
On 9/22/22 12:12, Quentin Schulz wrote:
[...]
> diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
> new file mode 100644
> index 000000000000..74a7f1182c21
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
> @@ -0,0 +1,347 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
> + */
> +
> +/dts-v1/;
> +#include "px30.dtsi"
> +
> +/ {
> + aliases {
> + mmc0 = &emmc;
> + mmc1 = &sdio;
> + rtc0 = &rtc_twi;
> + rtc1 = &rk809;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + pinctrl-0 = <&emmc_reset>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio1 RK_PB3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&module_led_pin>;
> + status = "okay";
> +
> + module_led: led-0 {
> + label = "module_led";
> + gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + vcc5v0_sys: vccsys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + supports-emmc;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + non-removable;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_emmc>;
> +
> + status = "okay";
> +};
> +
> +/* On-module TI DP83825I PHY but no connector, enable in carrierboard */
> +&gmac {
> + snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 50000 50000>;
> + phy-supply = <&vcc_3v3>;
> + clock_in_out = "output";
> +};
> +
I forgot:
&gpio2 {
/*
* The Qseven BIOS_DISABLE signal on the PX30-µQ7 keeps the
on-module
* eMMC powered-down initially (in fact it keeps the reset signal
* asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable eMMC.
*/
bios_disable_override {
gpios = <RK_PB5 GPIO_ACTIVE_LOW>;
output-high;
line-name = "bios_disable_override";
gpio-hog;
};
};
Since I had this change in the bootloader that was enough during my
tests, but better not rely on the bootloader whenever/wherever possible :)
I'll wait a bit for reviews before sending a v2 just for that.
Cheers,
Quentin
On 22/09/2022 12:12, Quentin Schulz wrote:
> From: Quentin Schulz <[email protected]>
>
> The PX30-uQ7 (Ringneck) SoM is a µQseven-compatible (40mmx70mm, MXM-230
> connector) system-on-module from Theobroma Systems[1], featuring the
> Rockchip PX30.
>
> It provides the following feature set:
> * up to 4GB DDR4
> * up to 128GB on-module eMMC (with 8-bit 1.8V interface)
> * SD card (on a baseboard) via edge connector
> * Fast Ethernet with on-module TI DP83825I PHY
> * MIPI-DSI/LVDS
> * MIPI-CSI
> * USB
> - 1x USB 2.0 dual-role
> - 3x USB 2.0 host
> * on-module STM32 Cortex-M0 companion controller, implementing:
> - low-power RTC functionality (ISL1208 emulation)
> - fan controller (AMC6821 emulation)
> - USB<->CAN bridge controller
> * on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
> * on-module NXP SE05x Secure Element
>
> [1] https://www.theobroma-systems.com/som-product/px30-%C2%B5q7/
>
> Signed-off-by: Quentin Schulz <[email protected]>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/px30-ringneck-haikou.dts | 239 ++++++++++++
> .../boot/dts/rockchip/px30-ringneck.dtsi | 347 ++++++++++++++++++
> 3 files changed, 587 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
> create mode 100644 arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index ef79a672804a..1e3b9d7c1a8b 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2-of10.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-edimm2.2.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-ringneck-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-s.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts b/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
> new file mode 100644
> index 000000000000..6304d6f7baa3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/px30-ringneck-haikou.dts
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
> + */
> +
> +/dts-v1/;
> +#include "px30-ringneck.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Theobroma Systems PX30-µQ7 SoM on Haikou devkit";
> + compatible = "tsd,px30-ringneck-haikou", "rockchip,px30";
> +
> + aliases {
> + mmc2 = &sdmmc;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + gpio_keys: haikou-keys {
By convention node name is gpio-keys
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&haikou_keys_pin>;
> + pinctrl-names = "default";
> +
> + BATLOWn {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
Missing generic node name, only lowercase characters.
> + label = "BATLOW#";
> + linux,code = <KEY_BATTERY>;
> + gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
> + };
> +
> + BIOS_DISABLEn {
> + label = "BIOS_DISABLE#";
> + linux,code = <SW_BOOT_ALT>;
> + linux,input-type = <EV_SW>;
> + gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + LID_BTNn {
> + label = "LID_BTN#";
> + linux,code = <SW_LID>;
> + linux,input-type = <EV_SW>;
> + gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
> + };
> +
> + SLP_BTNn {
> + label = "SLP_BTN#";
> + linux,code = <KEY_SLEEP>;
> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> + };
> +
> + WAKEn {
> + label = "WAKE#";
> + linux,code = <KEY_WAKEUP>;
> + gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + pinctrl-0 = <&module_led_pin>, <&sd_card_led_pin>;
> +
> + sd_card_led: led-1 {
> + label = "sd_card_led";
> + gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc2";
> + };
> + };
> +
> + i2s0-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "Haikou,I2S-codec";
> + simple-audio-card,mclk-fs = <512>;
> +
> + simple-audio-card,codec {
> + clocks = <&sgtl5000_clk>;
> + sound-dai = <&sgtl5000>;
> + };
> +
> + simple-audio-card,cpu {
> + bitclock-master;
> + frame-master;
> + sound-dai = <&i2s0_8ch>;
> + };
> + };
> +
> + sgtl5000_clk: sgtl5000-oscillator {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24576000>;
> + };
> +
> + dc_12v: dc-12v {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
So at least generic ("regulator") prefix or suffix.
> + compatible = "regulator-fixed";
> + regulator-name = "dc_12v";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + vcc3v3_baseboard: vcc3v3-baseboard {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_baseboard";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> + vcc5v0_baseboard: vcc5v0-baseboard {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_baseboard";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> + vdda_codec: vdda-codec {
> + compatible = "regulator-fixed";
> + regulator-name = "vdda_codec";
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_baseboard>;
> + };
> +
> + vddd_codec: vddd-codec {
> + compatible = "regulator-fixed";
> + regulator-name = "vddd_codec";
> + regulator-boot-on;
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <1600000>;
> + vin-supply = <&vcc5v0_baseboard>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + sgtl5000: codec@a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&sgtl5000_clk>;
> + #sound-dai-cells = <0>;
> + VDDA-supply = <&vdda_codec>;
> + VDDIO-supply = <&vcc3v3_baseboard>;
> + VDDD-supply = <&vddd_codec>;
> + status = "okay";
Okay is by default.
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> +
> + eeprom@50 {
> + reg = <0x50>;
> + compatible = "atmel,24c01";
> + pagesize = <8>;
> + size = <128>;
> + vcc-supply = <&vcc3v3_baseboard>;
> + };
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&gmac {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + haikou {
> + haikou_keys_pin: haikou-keys-pin {
> + rockchip,pins =
> + /* WAKE# */
> + <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> + /* SLP_BTN# */
> + <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + /* LID_BTN */
> + <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + /* BATLOW# */
> + <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> + /* BIOS_DISABLE# */
> + <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + leds {
> + sd_card_led_pin: sd-card-led-pin {
> + rockchip,pins =
> + <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + vmmc-supply = <&vcc3v3_baseboard>;
> + status = "okay";
> +};
> +
> +&spi1 {
> + status = "okay";
> +};
> +
> +&u2phy_otg {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-0 = <&uart5_xfer>;
> + status = "okay";
> +};
> +
> +&usb20_otg {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
> new file mode 100644
> index 000000000000..74a7f1182c21
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
> @@ -0,0 +1,347 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
> + */
> +
> +/dts-v1/;
> +#include "px30.dtsi"
> +
> +/ {
> + aliases {
> + mmc0 = &emmc;
> + mmc1 = &sdio;
> + rtc0 = &rtc_twi;
> + rtc1 = &rk809;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + pinctrl-0 = <&emmc_reset>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio1 RK_PB3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
This belongs to DTSI.
> + pinctrl-names = "default";
> + pinctrl-0 = <&module_led_pin>;
> + status = "okay";
No need.
> +
> + module_led: led-0 {
Why DTSI - which in logic comes first - starts with 1 and this is 0?\
> + label = "module_led";
> + gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + vcc5v0_sys: vccsys {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + supports-emmc;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + non-removable;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_emmc>;
> +
> + status = "okay";
> +};
> +
> +/* On-module TI DP83825I PHY but no connector, enable in carrierboard */
> +&gmac {
> + snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 50000 50000>;
> + phy-supply = <&vcc_3v3>;
> + clock_in_out = "output";
> +};
> +
> +&gpu {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rk809: pmic@20 {
> + compatible = "rockchip,rk809";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-0 = <&pmic_int>;
> + pinctrl-names = "default";
> + #clock-cells = <0>;
> + clock-output-names = "xin32k";
> + rockchip,system-power-controller;
> + wakeup-source;
> + status = "okay";
No need.
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc_3v3>;
> + vcc6-supply = <&vcc_3v3>;
> + vcc7-supply = <&vcc_3v3>;
> + vcc9-supply = <&vcc5v0_sys>;
> +
(...)
> +&pinctrl {
> + emmc {
> + emmc_reset: emmc-reset {
> + rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + module_led_pin: module-led-pin {
> + rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int: pmic_int {
No underscores in node names.
> + rockchip,pins =
> + <0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> +
Skip unneeded blank lines.
> +};
> +
> +&tsadc {
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +};
> +
> +&u2phy_host {
> + status = "okay";
> +};
> +
> +/* Mule UCAN */
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
Best regards,
Krzysztof
Hi Krzysztof,
On 9/22/22 14:45, Krzysztof Kozlowski wrote:
> On 22/09/2022 12:12, Quentin Schulz wrote:
[...]
>> diff --git a/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
>> new file mode 100644
>> index 000000000000..74a7f1182c21
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/px30-ringneck.dtsi
>> @@ -0,0 +1,347 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
>> + */
>> +
>> +/dts-v1/;
>> +#include "px30.dtsi"
>> +
>> +/ {
>> + aliases {
>> + mmc0 = &emmc;
>> + mmc1 = &sdio;
>> + rtc0 = &rtc_twi;
>> + rtc1 = &rk809;
>> + };
>> +
>> + emmc_pwrseq: emmc-pwrseq {
>> + compatible = "mmc-pwrseq-emmc";
>> + pinctrl-0 = <&emmc_reset>;
>> + pinctrl-names = "default";
>> + reset-gpios = <&gpio1 RK_PB3 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>
> This belongs to DTSI.
>
It is in the DTSI :)
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&module_led_pin>;
>> + status = "okay";
>
> No need.
>
>> +
>> + module_led: led-0 {
>
> Why DTSI - which in logic comes first - starts with 1 and this is 0?\
>
The first diff in this patch is for the DTS, this is now the DTSI. So it
does have led-0 in the DTSI and led-1 in the DTS which I think is what
you're requesting here? Is this a correct assumption?
Ack for all other review comments, thanks!
Cheers,
Quentin
On 23/09/2022 11:55, Quentin Schulz wrote:
>>> +
>>> + leds {
>>> + compatible = "gpio-leds";
>>
>> This belongs to DTSI.
>>
>
> It is in the DTSI :)
Ah, right...
>
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&module_led_pin>;
>>> + status = "okay";
>>
>> No need.
>>
>>> +
>>> + module_led: led-0 {
>>
>> Why DTSI - which in logic comes first - starts with 1 and this is 0?\
>>
>
> The first diff in this patch is for the DTS, this is now the DTSI. So it
> does have led-0 in the DTSI and led-1 in the DTS which I think is what
> you're requesting here? Is this a correct assumption?
Yep.
Best regards,
Krzysztof