From: Patrick Brünn <[email protected]>
On Tue, Dec 1, 2015 at 20:52:25 PST, [email protected] wrote:
> On Thu, Nov 26, 2015 at 11:59:15AM +0100, [email protected] wrote:
>> MX53_PAD_EIM_D27__UART2_RXD_MUX and MX53_PAD_EIM_D29__UART2_RTS input_val must be configured as 0 instead of 1 to have UART2 muxed on EIM pins working
>
> I'm not sure why you think that. But the i.MX53 Reference Manual in my hands doesn't agree with that. It says ...
>>
>> Signed-off-by: Patrick Brünn <[email protected]>
>> ---
>> arch/arm/boot/dts/imx53-pinfunc.h | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h
>> index aec406b..a4c973d 100644
>> --- a/arch/arm/boot/dts/imx53-pinfunc.h
>> +++ b/arch/arm/boot/dts/imx53-pinfunc.h
>> @@ -532,7 +532,7 @@
>> #define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0
>> #define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0
>> #define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0
>> -#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1
>> +#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x0
>
> IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT DAISY field descriptions
>
> 000 - Selecting Pad: EIM_D26 for Mode: ALT2.
> 001 - Selecting Pad: EIM_D27 for Mode: ALT2.
> 010 - Selecting Pad: PATA_DMARQ for Mode: ALT3.
> 011 - Selecting Pad: PATA_BUFFER_EN for Mode: ALT3.
> 100 - Selecting Pad: GPIO_7 for Mode: ALT4.
> 101 - Selecting Pad: GPIO_8 for Mode: ALT4.
Thanks for the hint. I had a closer look at the reference manual and our schematics. Of course, you are right. The defines are good as they are, my patch was stupid.
I just realized RXD and TXD are inverted on our hardware (CX9020 Embedded PC). Which requires a pinmux configuration like this:
EIM_D26->UART2_RXD
EIM_D27->UART2_TXD
EIM_D28->UART2_RTS
EIM_D29->UART2_CTS
In my opinion the reference manual allows such a configuration, but I am not sure if it's appropriate for mainline.
Would you accept a patch like the following:
>8------------------------------------------------------8<
ARM: dts: imx53: add EIM pad config for UART2
Add another pinmux configuration to mux UART2 on EIM pads:
EIM_D26->UART2_RXD
EIM_D27->UART2_TXD
EIM_D28->UART2_RTS
EIM_D29->UART2_CTS
Signed-off-by: Patrick Brünn <[email protected]>
---
arch/arm/boot/dts/imx53-pinfunc.h | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h
index aec406b..7d26d16 100644
--- a/arch/arm/boot/dts/imx53-pinfunc.h
+++ b/arch/arm/boot/dts/imx53-pinfunc.h
@@ -525,6 +525,7 @@
#define MX53_PAD_EIM_D26__EMI_WEIM_D_26 0x144 0x48c 0x000 0x0 0x0
#define MX53_PAD_EIM_D26__GPIO3_26 0x144 0x48c 0x000 0x1 0x0
#define MX53_PAD_EIM_D26__UART2_TXD_MUX 0x144 0x48c 0x000 0x2 0x0
+#define MX53_PAD_EIM_D26__UART2_RXD_MUX 0x144 0x48c 0x880 0x2 0x0
#define MX53_PAD_EIM_D26__FIRI_RXD 0x144 0x48c 0x80c 0x3 0x0
#define MX53_PAD_EIM_D26__IPU_CSI0_D_1 0x144 0x48c 0x000 0x4 0x0
#define MX53_PAD_EIM_D26__IPU_DI1_PIN11 0x144 0x48c 0x000 0x5 0x0
@@ -532,6 +533,7 @@
#define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0
#define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0
#define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0
+#define MX53_PAD_EIM_D27__UART2_TXD_MUX 0x148 0x490 0x000 0x2 0x0
#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1
#define MX53_PAD_EIM_D27__FIRI_TXD 0x148 0x490 0x000 0x3 0x0
#define MX53_PAD_EIM_D27__IPU_CSI0_D_0 0x148 0x490 0x000 0x4 0x0
@@ -541,6 +543,7 @@
#define MX53_PAD_EIM_D28__EMI_WEIM_D_28 0x14c 0x494 0x000 0x0 0x0
#define MX53_PAD_EIM_D28__GPIO3_28 0x14c 0x494 0x000 0x1 0x0
#define MX53_PAD_EIM_D28__UART2_CTS 0x14c 0x494 0x000 0x2 0x0
+#define MX53_PAD_EIM_D28__UART2_RTS 0x14c 0x494 0x87c 0x2 0x0
#define MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO 0x14c 0x494 0x82c 0x3 0x1
#define MX53_PAD_EIM_D28__CSPI_MOSI 0x14c 0x494 0x788 0x4 0x1
#define MX53_PAD_EIM_D28__I2C1_SDA 0x14c 0x494 0x818 0x5 0x1
@@ -548,6 +551,7 @@
#define MX53_PAD_EIM_D28__IPU_DI0_PIN13 0x14c 0x494 0x000 0x7 0x0
#define MX53_PAD_EIM_D29__EMI_WEIM_D_29 0x150 0x498 0x000 0x0 0x0
#define MX53_PAD_EIM_D29__GPIO3_29 0x150 0x498 0x000 0x1 0x0
+#define MX53_PAD_EIM_D29__UART2_CTS 0x150 0x498 0x000 0x2 0x0
#define MX53_PAD_EIM_D29__UART2_RTS 0x150 0x498 0x87c 0x2 0x1
#define MX53_PAD_EIM_D29__IPU_DISPB0_SER_RS 0x150 0x498 0x000 0x3 0x0
#define MX53_PAD_EIM_D29__CSPI_SS0 0x150 0x498 0x78c 0x4 0x2
--
1.9.1
On Mon, Dec 07, 2015 at 02:48:04PM +0100, [email protected] wrote:
> From: Patrick Br?nn <[email protected]>
>
> On Tue, Dec 1, 2015 at 20:52:25 PST, [email protected] wrote:
> > On Thu, Nov 26, 2015 at 11:59:15AM +0100, [email protected] wrote:
> >> MX53_PAD_EIM_D27__UART2_RXD_MUX and MX53_PAD_EIM_D29__UART2_RTS input_val must be configured as 0 instead of 1 to have UART2 muxed on EIM pins working
> >
> > I'm not sure why you think that. But the i.MX53 Reference Manual in my hands doesn't agree with that. It says ...
> >>
> >> Signed-off-by: Patrick Br?nn <[email protected]>
> >> ---
> >> arch/arm/boot/dts/imx53-pinfunc.h | 4 ++--
> >> 1 file changed, 2 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h
> >> index aec406b..a4c973d 100644
> >> --- a/arch/arm/boot/dts/imx53-pinfunc.h
> >> +++ b/arch/arm/boot/dts/imx53-pinfunc.h
> >> @@ -532,7 +532,7 @@
> >> #define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0
> >> #define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0
> >> #define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0
> >> -#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1
> >> +#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x0
> >
> > IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT DAISY field descriptions
> >
> > 000 - Selecting Pad: EIM_D26 for Mode: ALT2.
> > 001 - Selecting Pad: EIM_D27 for Mode: ALT2.
> > 010 - Selecting Pad: PATA_DMARQ for Mode: ALT3.
> > 011 - Selecting Pad: PATA_BUFFER_EN for Mode: ALT3.
> > 100 - Selecting Pad: GPIO_7 for Mode: ALT4.
> > 101 - Selecting Pad: GPIO_8 for Mode: ALT4.
>
>
> Thanks for the hint. I had a closer look at the reference manual and our schematics. Of course, you are right. The defines are good as they are, my patch was stupid.
>
> I just realized RXD and TXD are inverted on our hardware (CX9020 Embedded PC). Which requires a pinmux configuration like this:
> EIM_D26->UART2_RXD
> EIM_D27->UART2_TXD
> EIM_D28->UART2_RTS
> EIM_D29->UART2_CTS
>
> In my opinion the reference manual allows such a configuration, but I am not sure if it's appropriate for mainline.
>
> Would you accept a patch like the following:
No, I'm not going to accept it. But it doesn't mean you cannot define
and use it in your own board DTS file.
Shawn
>
> >8------------------------------------------------------8<
> ARM: dts: imx53: add EIM pad config for UART2
>
> Add another pinmux configuration to mux UART2 on EIM pads:
>
> EIM_D26->UART2_RXD
> EIM_D27->UART2_TXD
> EIM_D28->UART2_RTS
> EIM_D29->UART2_CTS
>
> Signed-off-by: Patrick Br?nn <[email protected]>
> ---
> arch/arm/boot/dts/imx53-pinfunc.h | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h
> index aec406b..7d26d16 100644
> --- a/arch/arm/boot/dts/imx53-pinfunc.h
> +++ b/arch/arm/boot/dts/imx53-pinfunc.h
> @@ -525,6 +525,7 @@
> #define MX53_PAD_EIM_D26__EMI_WEIM_D_26 0x144 0x48c 0x000 0x0 0x0
> #define MX53_PAD_EIM_D26__GPIO3_26 0x144 0x48c 0x000 0x1 0x0
> #define MX53_PAD_EIM_D26__UART2_TXD_MUX 0x144 0x48c 0x000 0x2 0x0
> +#define MX53_PAD_EIM_D26__UART2_RXD_MUX 0x144 0x48c 0x880 0x2 0x0
> #define MX53_PAD_EIM_D26__FIRI_RXD 0x144 0x48c 0x80c 0x3 0x0
> #define MX53_PAD_EIM_D26__IPU_CSI0_D_1 0x144 0x48c 0x000 0x4 0x0
> #define MX53_PAD_EIM_D26__IPU_DI1_PIN11 0x144 0x48c 0x000 0x5 0x0
> @@ -532,6 +533,7 @@
> #define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0
> #define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0
> #define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0
> +#define MX53_PAD_EIM_D27__UART2_TXD_MUX 0x148 0x490 0x000 0x2 0x0
> #define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1
> #define MX53_PAD_EIM_D27__FIRI_TXD 0x148 0x490 0x000 0x3 0x0
> #define MX53_PAD_EIM_D27__IPU_CSI0_D_0 0x148 0x490 0x000 0x4 0x0
> @@ -541,6 +543,7 @@
> #define MX53_PAD_EIM_D28__EMI_WEIM_D_28 0x14c 0x494 0x000 0x0 0x0
> #define MX53_PAD_EIM_D28__GPIO3_28 0x14c 0x494 0x000 0x1 0x0
> #define MX53_PAD_EIM_D28__UART2_CTS 0x14c 0x494 0x000 0x2 0x0
> +#define MX53_PAD_EIM_D28__UART2_RTS 0x14c 0x494 0x87c 0x2 0x0
> #define MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO 0x14c 0x494 0x82c 0x3 0x1
> #define MX53_PAD_EIM_D28__CSPI_MOSI 0x14c 0x494 0x788 0x4 0x1
> #define MX53_PAD_EIM_D28__I2C1_SDA 0x14c 0x494 0x818 0x5 0x1
> @@ -548,6 +551,7 @@
> #define MX53_PAD_EIM_D28__IPU_DI0_PIN13 0x14c 0x494 0x000 0x7 0x0
> #define MX53_PAD_EIM_D29__EMI_WEIM_D_29 0x150 0x498 0x000 0x0 0x0
> #define MX53_PAD_EIM_D29__GPIO3_29 0x150 0x498 0x000 0x1 0x0
> +#define MX53_PAD_EIM_D29__UART2_CTS 0x150 0x498 0x000 0x2 0x0
> #define MX53_PAD_EIM_D29__UART2_RTS 0x150 0x498 0x87c 0x2 0x1
> #define MX53_PAD_EIM_D29__IPU_DISPB0_SER_RS 0x150 0x498 0x000 0x3 0x0
> #define MX53_PAD_EIM_D29__CSPI_SS0 0x150 0x498 0x78c 0x4 0x2
> --
> 1.9.1
>