Changelog:
- v9:
- fix some warnings.
- use the new pin defined for pinctrl.
- v8:
- add the missing LDOs for PMIC, the pins for LDOs are not avaiabled in core
board.
- re-order the header files in core board.
- skip the vendor prefix file
- v7:
- add a missing header file
- add a rootdelay to bootargs or it can't mount root filesystem
- fix the memory node
- v6:
- move pwms pinctrl to pwms node
- fix the order of the dtb file in Makefile
- v5:
- correct the mail format
- v4:
- re-order some nodes in alphabetical order
- fix some minor bugs
- add a entry in vendor list
- v3:
- fixing the rtc clock, using clock source from PMIC
- enable the tmu
- enable the fimc for elite board
- suuport the audio codec at elite board, but the audio sound a little
distortion
- fixing minor bugs in the last commit
- v2:
- removing rtc node
the clock source driver is not done yet.
- adding exynos-bus
- fixing the MFC
Randy Li (2):
ARM: dts: Add TOPEET itop core board SCP package version
ARM: dts: add TOPEET itop elite based board
.../bindings/arm/samsung/samsung-boards.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 ++++++++++
arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 +++++++++++++++++++++
4 files changed, 745 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts
create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
--
2.7.4
The TOPEET itop is a samsung exnynos 4412 core board, which have
two package versions. This patch add the support for SCP version.
Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and
PMIC. The future features are in the based board. Also MFC and
watchdog have been enabled.
Signed-off-by: Randy Li <[email protected]>
---
arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++
1 file changed, 501 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
new file mode 100644
index 0000000..881dc76
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
@@ -0,0 +1,501 @@
+/*
+ * TOPEET's Exynos4412 based itop board device tree source
+ *
+ * Copyright (c) 2016 SUMOMO Computer Association
+ * https://www.sumomo.mobi
+ * Randy Li <[email protected]>
+ *
+ * Device tree source file for TOPEET iTop Exynos 4412 SCP package core
+ * board which is based on Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "exynos4412.dtsi"
+#include "exynos4412-ppmu-common.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
+
+/ {
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x40000000>;
+ };
+
+ firmware@0203F000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x0203F000 0x1000>;
+ };
+
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
+ };
+
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
+ };
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503a";
+ reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>;
+ connect-gpios = <&gpm3 3 GPIO_ACTIVE_HIGH>;
+ intn-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsic_reset>;
+ };
+};
+
+&bus_dmc {
+ devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+ vdd-supply = <&buck1_reg>;
+ status = "okay";
+};
+
+&bus_acp {
+ devfreq = <&bus_dmc>;
+ status = "okay";
+};
+
+&bus_c2c {
+ devfreq = <&bus_dmc>;
+ status = "okay";
+};
+
+&bus_leftbus {
+ devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+ vdd-supply = <&buck3_reg>;
+ status = "okay";
+};
+
+&bus_rightbus {
+ devfreq = <&bus_leftbus>;
+ status = "okay";
+};
+
+&bus_fsys {
+ devfreq = <&bus_leftbus>;
+ status = "okay";
+};
+
+&bus_peri {
+ devfreq = <&bus_leftbus>;
+ status = "okay";
+};
+
+&bus_mfc {
+ devfreq = <&bus_leftbus>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu0-supply = <&buck2_reg>;
+};
+
+&hsotg {
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+};
+
+&i2c_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c1_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ s5m8767: s5m8767-pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+
+ s5m8767,pmic-buck-default-dvs-idx = <3>;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>,
+ <&gpb 6 GPIO_ACTIVE_HIGH>,
+ <&gpb 7 GPIO_ACTIVE_HIGH>;
+
+ s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>,
+ <&gpm3 6 GPIO_ACTIVE_HIGH>,
+ <&gpm3 7 GPIO_ACTIVE_HIGH>;
+
+ /* VDD_ARM */
+ s5m8767,pmic-buck2-dvs-voltage = <1356250>, <1300000>,
+ <1243750>, <1118750>,
+ <1068750>, <1012500>,
+ <956250>, <900000>;
+ /* VDD_INT */
+ s5m8767,pmic-buck3-dvs-voltage = <1000000>, <1000000>,
+ <925000>, <925000>,
+ <887500>, <887500>,
+ <850000>, <850000>;
+ /* VDD_G3D */
+ s5m8767,pmic-buck4-dvs-voltage = <1081250>, <1081250>,
+ <1025000>, <950000>,
+ <918750>, <900000>,
+ <875000>, <831250>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ /* SCP uses 1.5v, POP uses 1.2v */
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M12";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDIOAP_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_PRE";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD_LDO5";
+ op_mode = <0>; /* Always off Mode */
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD10_MIPI";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD33_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD18_MIPI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_UOTG";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDIOPERI_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB02";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_USH";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDDIOAP_MMC012_28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ /* Used by HSIC */
+ ldo18_reg: LDO18 {
+ regulator-name = "VDDIOPERI_28";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "VDD_LDO19";
+ op_mode = <0>; /* Always off Mode */
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "VDD28_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VDD28_AF";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "VDDA28_2M";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "VDD28_TF";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "VDD33_A31";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "VDD18_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "VDD18_A31";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "GPS_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "DVDD12";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1456250>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "vdd_m12";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "vdd12_5m";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "pvdd_buck7";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "pvdd_buck8";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "vddf28_emmc";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3000000>;
+ op_mode = <1>; /* Normal Mode */
+ };
+ };
+
+ s5m8767_osc: clocks {
+ #clock-cells = <1>;
+ clock-output-names = "s5m8767_ap",
+ "s5m8767_cp", "s5m8767_bt";
+ };
+
+ };
+};
+
+&mfc {
+ status = "okay";
+};
+
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ status = "okay";
+ vmmc-supply = <&buck9_reg>;
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
+&pinctrl_1 {
+ hsic_reset: hsic-reset {
+ samsung,pins = "gpm2-4";
+ samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+ };
+};
+
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
+ clock-names = "rtc", "rtc_src";
+};
+
+&tmu {
+ vtmu-supply = <&ldo16_reg>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.7.4
The TOPEET itop exynos 4412 have three versions base board. The
Elite version is the cheap one without too much peripheral devices
on it.
Currently supported are serial console, wired networking(USB),
USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
enabled.
The FIMC is not used for camera currently, I enabled it just for a
colorspace converter.
Signed-off-by: Randy Li <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
---
.../bindings/arm/samsung/samsung-boards.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/exynos4412-itop-elite.dts | 240 +++++++++++++++++++++
3 files changed, 244 insertions(+)
create mode 100644 arch/arm/boot/dts/exynos4412-itop-elite.dts
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
index 0ea7f14..5160fa5 100644
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
@@ -22,6 +22,9 @@ Required root node properties:
* FriendlyARM
- "friendlyarm,tiny4412" - for Exynos4412-based FriendlyARM
TINY4412 board.
+ * TOPEET
+ - "topeet,itop4412-elite" - for Exynos4412-based TOPEET
+ Elite base board.
* Google
- "google,pi" - for Exynos5800-based Google Peach Pi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd26..d709f74 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \
exynos4210-smdkv310.dtb \
exynos4210-trats.dtb \
exynos4210-universal_c210.dtb \
+ exynos4412-itop-elite.dtb \
exynos4412-odroidu3.dtb \
exynos4412-odroidx.dtb \
exynos4412-odroidx2.dtb \
diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
new file mode 100644
index 0000000..7440e54
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
@@ -0,0 +1,240 @@
+/*
+ * TOPEET's Exynos4412 based itop board device tree source
+ *
+ * Copyright (c) 2016 SUMOMO Computer Association
+ * https://www.sumomo.mobi
+ * Randy Li <[email protected]>
+ *
+ * Device tree source file for TOPEET iTop Exynos 4412 core board
+ * which is based on Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/sound/samsung-i2s.h>
+#include "exynos4412-itop-scp-core.dtsi"
+
+/ {
+ model = "TOPEET iTop 4412 Elite board based on Exynos4412";
+ compatible = "topeet,itop4412-elite", "samsung,exynos4412", "samsung,exynos4";
+
+ chosen {
+ bootargs = "root=/dev/mmcblk0p2 rw rootfstype=ext4 rootdelay=1 rootwait";
+ stdout-path = "serial2:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led2 {
+ label = "red:system";
+ gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led3 {
+ label = "red:user";
+ gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ home {
+ label = "GPIO Key Home";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpx1 1 GPIO_ACTIVE_LOW>;
+ };
+
+ back {
+ label = "GPIO Key Back";
+ linux,code = <KEY_BACK>;
+ gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ sleep {
+ label = "GPIO Key Sleep";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
+ };
+
+ vol-up {
+ label = "GPIO Key Vol+";
+ linux,code = <KEY_UP>;
+ gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ vol-down {
+ label = "GPIO Key Vol-";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "wm-sound";
+
+ assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
+ <&clock_audss EXYNOS_MOUT_I2S>,
+ <&clock_audss EXYNOS_DOUT_SRP>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>;
+ assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
+ <&clock_audss EXYNOS_MOUT_AUDSS>;
+ assigned-clock-rates = <0>,
+ <0>,
+ <112896000>,
+ <11289600>;
+
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&link0_codec>;
+ simple-audio-card,frame-master = <&link0_codec>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In",
+ "Line", "Line Out",
+ "Speaker", "Speaker",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Speaker", "SPK_LP",
+ "Speaker", "SPK_LN",
+ "Speaker", "SPK_RP",
+ "Speaker", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "LINPUT3", "Mic Jack",
+ "RINPUT1", "Mic Jack",
+ "RINPUT2", "Mic Jack";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s0 0>;
+ };
+
+ link0_codec: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&i2s0 CLK_I2S_CDCLK>;
+ system-clock-frequency = <11289600>;
+ };
+ };
+
+ beep {
+ compatible = "pwm-beeper";
+ pwms = <&pwm 0 4000000 PWM_POLARITY_INVERTED>;
+ };
+
+ camera: camera {
+ pinctrl-0 = <&cam_port_a_clk_active>;
+ pinctrl-names = "default";
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_CAM0>;
+ assigned-clock-parents = <&clock CLK_XUSBXTI>;
+ };
+};
+
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&ehci {
+ status = "okay";
+ /* In order to reset USB ethernet */
+ samsung,vbus-gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
+
+ port@0 {
+ status = "okay";
+ };
+
+ port@2 {
+ status = "okay";
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&hsotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_4 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c4_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ codec: wm8960@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&pmu_system_controller 0>;
+ clock-names = "MCLK1";
+ wlf,shared-lrclk;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+};
+
+&pinctrl_1 {
+ ether-reset {
+ samsung,pins = "gpc0-1";
+ samsung,pin-function = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+};
+
+&pwm {
+ status = "okay";
+ pinctrl-0 = <&pwm0_out>;
+ pinctrl-names = "default";
+ samsung,pwm-outputs = <0>;
+};
+
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+ pinctrl-names = "default";
+ cd-gpio = <&gpx0 7 GPIO_ACTIVE_LOW>;
+ cap-sd-highspeed;
+ vmmc-supply = <&ldo23_reg>;
+ vqmmc-supply = <&ldo17_reg>;
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
--
2.7.4
On Wed, Oct 19, 2016 at 01:18:48AM +0800, Randy Li wrote:
> The TOPEET itop is a samsung exnynos 4412 core board, which have
> two package versions. This patch add the support for SCP version.
>
> Currently supported are USB3503A HSIC, USB OTG, eMMC, rtc and
> PMIC. The future features are in the based board. Also MFC and
> watchdog have been enabled.
>
> Signed-off-by: Randy Li <[email protected]>
> ---
> arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi | 501 ++++++++++++++++++++++++
> 1 file changed, 501 insertions(+)
> create mode 100644 arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
Thanks, applied, with minor changes in commit msg and fix in pin
function (you used macro for pull up/down instead of function).
Best regards,
Krzysztof
On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote:
> The TOPEET itop exynos 4412 have three versions base board. The
> Elite version is the cheap one without too much peripheral devices
> on it.
>
> Currently supported are serial console, wired networking(USB),
> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
> enabled.
>
> The FIMC is not used for camera currently, I enabled it just for a
> colorspace converter.
>
> Signed-off-by: Randy Li <[email protected]>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
Thanks, applied, with missing Rob's ack, minor changes in commit msg and
fix in pin function (you used macro for pull up/down instead of
function).
Best regards,
Krzysztof
On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote:
> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote:
> > The TOPEET itop exynos 4412 have three versions base board. The
> > Elite version is the cheap one without too much peripheral devices
> > on it.
> >
> > Currently supported are serial console, wired networking(USB),
> > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
> > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
> > enabled.
> >
> > The FIMC is not used for camera currently, I enabled it just for a
> > colorspace converter.
> >
> > Signed-off-by: Randy Li <[email protected]>
> > Reviewed-by: Krzysztof Kozlowski <[email protected]>
>
> Thanks, applied, with missing Rob's ack, minor changes in commit msg and
> fix in pin function (you used macro for pull up/down instead of
> function).
I also changed your name in commit message from "ayaka" to "Randy Li".
The author of a patch (equal to "From:" in email) should match the
Signed-off-by. For the future, please fix your gitconfig and/or mail
transfer program.
Sample gitconfig regarding this:
[user]
name = Mr Foo Bar
email = [email protected]
[sendemail]
smtpencryption = tls
smtpserver = smtp.gmail.com
smtpuser = [email protected]
smtpserverport = 587
confirm = auto
Best regards,
Krzysztof
On Tue, Oct 18, 2016 at 8:47 PM, Krzysztof Kozlowski <[email protected]> wrote:
> On Tue, Oct 18, 2016 at 08:37:48PM +0300, Krzysztof Kozlowski wrote:
>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote:
>> > The TOPEET itop exynos 4412 have three versions base board. The
>> > Elite version is the cheap one without too much peripheral devices
>> > on it.
>> >
>> > Currently supported are serial console, wired networking(USB),
>> > USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
>> > PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
>> > enabled.
>> >
>> > The FIMC is not used for camera currently, I enabled it just for a
>> > colorspace converter.
>> >
>> > Signed-off-by: Randy Li <[email protected]>
>> > Reviewed-by: Krzysztof Kozlowski <[email protected]>
>>
>> Thanks, applied, with missing Rob's ack, minor changes in commit msg and
>> fix in pin function (you used macro for pull up/down instead of
>> function).
>
> I also changed your name in commit message from "ayaka" to "Randy Li".
> The author of a patch (equal to "From:" in email) should match the
> Signed-off-by. For the future, please fix your gitconfig and/or mail
> transfer program.
Ahhh, it is not your fault but patchwork's. Damn it. Patchwork stores
the first username he encounters and uses it further even if From is
different.
I will send an email to kernel.org Patchwork admin about this.
Best regards,
Krzysztof
On Wed, Oct 19, 2016 at 4:15 AM, Ayaka <[email protected]> wrote:
>
>
> 從我的 iPad 傳送
>
>> Krzysztof Kozlowski <[email protected]> 於 2016年10月19日 上午1:37 寫道：
>>
>>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote:
>>> The TOPEET itop exynos 4412 have three versions base board. The
>>> Elite version is the cheap one without too much peripheral devices
>>> on it.
>>>
>>> Currently supported are serial console, wired networking(USB),
>>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
>>> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
>>> enabled.
>>>
>>> The FIMC is not used for camera currently, I enabled it just for a
>>> colorspace converter.
>>>
>>> Signed-off-by: Randy Li <[email protected]>
>>> Reviewed-by: Krzysztof Kozlowski <[email protected]>
>>
>> Thanks, applied, with missing Rob's ack, minor changes in commit msg and
>> fix in pin function (you used macro for pull up/down instead of
>> function).
> The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that.
I wonder why I didn't encounter the build error on my machine... This
needs a follow up fix.
Best regards,
Krzysztof