This patchsets adds the MMC nodes in the GX dtsi and adds the GXBB clocks
attributes in the GXBB dtsi.
Then MMC/SD/SDIO support is added to :
- p20x : SD, SDIO, MMC
- a95x : SD, SDIO, MMC
- Odroid-C2 : SD, MMC
WiFi support is also added by enabling the 32768Hz clock generated by PWM
on p20x and A95x and adding the SDIO power sequence.
This patchset is based on Kevin Hilman's amlogic v4.10/dt64 tree at [1]
[1] git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic.git
Kevin Hilman (1):
ARM64: dts: meson-gxbb: add MMC support
Neil Armstrong (3):
ARM64: dts: meson-gxbb: Add Wifi 32K clock for p20x boards
ARM64: dts: meson-gxbb: Add P20x Wifi SDIO support
ARM64: dts: meson-gxbb: Add MMC nodes to Nexbox A95x
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 21 ++++
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 122 ++++++++++++++++++++
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 88 ++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 127 +++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 24 +++-
5 files changed, 381 insertions(+), 1 deletion(-)
--
1.9.1
Add a 32768Hz clock generated by the PWM E port used by the WiFi module.
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 86e740f..6861b0a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -111,6 +111,13 @@
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -205,3 +212,11 @@
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
--
1.9.1
Add support for eMMC/SD/SDIO on the Nexbox A95x.
Signed-off-by: Neil Armstrong <[email protected]>
---
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 122 +++++++++++++++++++++
1 file changed, 122 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index 399d85f..9696820 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -87,6 +87,61 @@
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
};
};
+
+ vddio_card: gpio-regulator {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VDDIO_CARD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+
+ /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+ states = <1800000 0
+ 3300000 1>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
};
&uart_AO {
@@ -107,3 +162,70 @@
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
--
1.9.1
Add Wifi module support on the Amlogic P20x boards on the SDIO port.
The Wifi module also needs a 32768Hz clock provided by the PWM E port
through a pwm-clock node in it's power sequence.
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 6861b0a..203be28 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -118,6 +118,13 @@
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -171,8 +178,15 @@
non-removable;
disable-wp;
+ mmc-pwrseq = <&sdio_pwrseq>;
+
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
};
/* SD card */
--
1.9.1
From: Kevin Hilman <[email protected]>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Kevin Hilman <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 21 +++++
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 88 +++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 98 ++++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 24 +++++-
4 files changed, 230 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
index a6cd953..fd1d0de 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -203,6 +203,27 @@
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+
+ sd_emmc_a: mmc@70000 {
+ compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x70000 0x0 0x2000>;
+ interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ sd_emmc_b: mmc@72000 {
+ compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x72000 0x0 0x2000>;
+ interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ sd_emmc_c: mmc@74000 {
+ compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x74000 0x0 0x2000>;
+ interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
};
};
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index a45d101..238fbea 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -85,6 +85,56 @@
default-state = "off";
};
};
+
+ tflash_vdd: regulator-tflash_vdd {
+ /*
+ * signal name from schematics: TFLASH_VDD_EN
+ */
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_ao GPIOAO_12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ /*
+ * signal name from schematics: TF_3V3N_1V8_EN
+ */
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0
+ 1800000 1>;
+ };
+
+ vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
};
&uart_AO {
@@ -127,3 +177,41 @@
&usb1 {
status = "okay";
};
+
+/* SD */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc3v3>;
+ vqmmc-supply = <&vcc1v8>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 031d69b..86e740f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -70,6 +70,47 @@
gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ vddio_card: gpio-regulator {
+ compatible = "regulator-gpio";
+
+ regulator-name = "VDDIO_CARD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+
+ /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
+ states = <1800000 0
+ 3300000 1>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
};
/* This UART is brought out to the DB9 connector */
@@ -107,3 +148,60 @@
&usb1 {
status = "okay";
};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_card>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index aad639a..22940bb 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -349,7 +349,8 @@
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
- "emmc_clk";
+ "emmc_clk",
+ "emmc_ds";
function = "emmc";
};
};
@@ -545,3 +546,24 @@
#mbox-cells = <1>;
};
};
+
+&sd_emmc_a {
+ clocks = <&clkc CLKID_SD_EMMC_A>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_b {
+ clocks = <&clkc CLKID_SD_EMMC_B>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_c {
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
--
1.9.1
Neil Armstrong <[email protected]> writes:
> From: Kevin Hilman <[email protected]>
>
> Add binding and basic support for the SD/eMMC controller on Amlogic
> S905/GXBB devices.
>
> Acked-by: Rob Herring <[email protected]>
> Signed-off-by: Kevin Hilman <[email protected]>
nit: you added a couple things from my original patch, and it's
customary to make a summary note of changes in the changelog, so before
applying, I added a line here:
[narmstrong: added nodes for GX, enabled SDIO on P20x]
> Signed-off-by: Neil Armstrong <[email protected]>
Applied to v4.10/dt64
Kevin