MT2712 is a SoC based on 64bit ARMv8 architecture.
MT2712 share many HW IP with MT8173. This patchset was tested on MT2712
evaluation board, and boot to shell ok.
This series contains document bindings, device tree including interrupt
and uart.
Changes compared to v2:
- remove alias from serial1 to serial5
- remove initrd-start and initrd-end
- change GIC_CPU_MASK_SIMPLE(6) to GIC_CPU_MASK_RAW(0x13)
- change gic-400 reg range
Changes compared to v1:
- change subject prefix for bindings
- change device tree license to SPDX tag.
- change bootargs parameter to DT usage.
- change intpol-controller to interrupt-controller
YT Shen (2):
dt-bindings: arm: Add bindings for Mediatek MT2712 SoC Platform
arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and
Makefile
Documentation/devicetree/bindings/arm/mediatek.txt | 4 +
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/serial/mtk-uart.txt | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 32 ++++
arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 166 +++++++++++++++++++++
6 files changed, 205 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
--
1.9.1
This adds dt-binding documentation for Mediatek MT2712.
Only include very basic items: cpu, gic and uart.
Signed-off-by: YT Shen <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/mediatek.txt | 4 ++++
.../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
Documentation/devicetree/bindings/serial/mtk-uart.txt | 1 +
3 files changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index c860b24..3161651 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -7,6 +7,7 @@ Required root node property:
compatible: Must contain one of
"mediatek,mt2701"
+ "mediatek,mt2712"
"mediatek,mt6580"
"mediatek,mt6589"
"mediatek,mt6592"
@@ -23,6 +24,9 @@ Supported boards:
- Evaluation board for MT2701:
Required root node properties:
- compatible = "mediatek,mt2701-evb", "mediatek,mt2701";
+- Evaluation board for MT2712:
+ Required root node properties:
+ - compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
- Evaluation board for MT6580:
Required root node properties:
- compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580";
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index a89c03b..653adb5 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -16,6 +16,7 @@ Required properties:
"mediatek,mt6580-sysirq"
"mediatek,mt6577-sysirq"
"mediatek,mt2701-sysirq"
+ "mediatek,mt2712-sysirq"
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
- interrupt-parent: phandle of irq parent for sysirq. The parent must
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index 0015c72..5f88e0d 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -3,6 +3,7 @@
Required properties:
- compatible should contain:
* "mediatek,mt2701-uart" for MT2701 compatible UARTS
+ * "mediatek,mt2712-uart" for MT2712 compatible UARTS
* "mediatek,mt6580-uart" for MT6580 compatible UARTS
* "mediatek,mt6582-uart" for MT6582 compatible UARTS
* "mediatek,mt6589-uart" for MT6589 compatible UARTS
--
1.9.1
This adds basic chip support for Mediatek 2712
Signed-off-by: YT Shen <[email protected]>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 32 ++++++
arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 166 ++++++++++++++++++++++++++++
3 files changed, 199 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 9fbfd32..fcc0604 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -1,3 +1,4 @@
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
new file mode 100644
index 0000000..8c804df
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -0,0 +1,32 @@
+/*
+ * Copyright (c) 2017 MediaTek Inc.
+ * Author: YT Shen <[email protected]>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+#include "mt2712e.dtsi"
+
+/ {
+ model = "MediaTek MT2712 evaluation board";
+ compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
new file mode 100644
index 0000000..65cdd4a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -0,0 +1,166 @@
+/*
+ * Copyright (c) 2017 MediaTek Inc.
+ * Author: YT Shen <[email protected]>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "mediatek,mt2712";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu2>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a35";
+ reg = <0x000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a35";
+ reg = <0x001>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x200>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ uart_clk: dummy26m {
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ #clock-cells = <0>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ uart5: serial@1000f000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x1000f000 0 0x400>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ sysirq: interrupt-controller@10220a80 {
+ compatible = "mediatek,mt2712-sysirq",
+ "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10220a80 0 0x40>;
+ };
+
+ gic: interrupt-controller@10510000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x10510000 0 0x10000>,
+ <0 0x10520000 0 0x20000>,
+ <0 0x10540000 0 0x20000>,
+ <0 0x10560000 0 0x20000>;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x400>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ uart3: serial@11005000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11005000 0 0x400>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+
+ uart4: serial@11019000 {
+ compatible = "mediatek,mt2712-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11019000 0 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&uart_clk>;
+ status = "disabled";
+ };
+ };
+};
+
--
1.9.1
On 16/06/17 15:45, YT Shen wrote:
> This adds basic chip support for Mediatek 2712
>
> Signed-off-by: YT Shen <[email protected]>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 32 ++++++
> arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 166 ++++++++++++++++++++++++++++
> 3 files changed, 199 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 9fbfd32..fcc0604 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -1,3 +1,4 @@
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> new file mode 100644
> index 0000000..8c804df
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> @@ -0,0 +1,32 @@
> +/*
> + * Copyright (c) 2017 MediaTek Inc.
> + * Author: YT Shen <[email protected]>
> + *
> + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> + */
> +
> +/dts-v1/;
> +#include "mt2712e.dtsi"
> +
> +/ {
> + model = "MediaTek MT2712 evaluation board";
> + compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> new file mode 100644
> index 0000000..65cdd4a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> @@ -0,0 +1,166 @@
[...]
> +
> + uart_clk: dummy26m {
> + compatible = "fixed-clock";
> + clock-frequency = <26000000>;
> + #clock-cells = <0>;
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13
> + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14
> + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11
> + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10
> + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + uart5: serial@1000f000 {
> + compatible = "mediatek,mt2712-uart",
> + "mediatek,mt6577-uart";
> + reg = <0 0x1000f000 0 0x400>;
> + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&uart_clk>;
uart has two clocks, baud and bus clock. Please refer to the bindings
descrption for more information, that's what they are for.
Please define the two dummy clocks with the correct frequency and use them.
Regards,
Matthias
On Fri, 2017-06-16 at 16:33 +0200, Matthias Brugger wrote:
>
> On 16/06/17 15:45, YT Shen wrote:
> > This adds basic chip support for Mediatek 2712
> >
> > Signed-off-by: YT Shen <[email protected]>
> > ---
> > arch/arm64/boot/dts/mediatek/Makefile | 1 +
> > arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 32 ++++++
> > arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 166 ++++++++++++++++++++++++++++
> > 3 files changed, 199 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index 9fbfd32..fcc0604 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -1,3 +1,4 @@
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > new file mode 100644
> > index 0000000..8c804df
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > @@ -0,0 +1,32 @@
> > +/*
> > + * Copyright (c) 2017 MediaTek Inc.
> > + * Author: YT Shen <[email protected]>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt2712e.dtsi"
> > +
> > +/ {
> > + model = "MediaTek MT2712 evaluation board";
> > + compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + reg = <0 0x40000000 0 0x80000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:921600n8";
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > new file mode 100644
> > index 0000000..65cdd4a
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > @@ -0,0 +1,166 @@
> [...]
> > +
> > + uart_clk: dummy26m {
> > + compatible = "fixed-clock";
> > + clock-frequency = <26000000>;
> > + #clock-cells = <0>;
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_PPI 13
> > + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14
> > + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11
> > + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10
> > + (GIC_CPU_MASK_RAW(0x13) | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + soc {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + compatible = "simple-bus";
> > + ranges;
> > +
> > + uart5: serial@1000f000 {
> > + compatible = "mediatek,mt2712-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x1000f000 0 0x400>;
> > + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&uart_clk>;
>
> uart has two clocks, baud and bus clock. Please refer to the bindings
> descrption for more information, that's what they are for.
>
> Please define the two dummy clocks with the correct frequency and use them.
>
> Regards,
> Matthias
Okay, after checking
Documentation/devicetree/bindings/serial/mtk-uart.txt, I will use baud
and bus clock in the next version.
yt.shen