This patch-set handles the SPDIFRX on STM32 platforms.
The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
IEC-60958 and IEC-61937 standards.
SPDIFRX uses two DMA channels:
- one DMA channel for S/PDIF data stream.
- one DMA channel for control flow (channel status and user data bits).
DMA is used for control flow instead of interrupts to get better performances,
as channel status and user data are retrieved byte per byte.
Note: This patch-set depends on "change SAI configuration flag" patch,
which introduces a change on Kconfig file.
olivier moysan (2):
dt-bindings: Document the STM32 SPDIFRX interface
ASoC: stm32: Add SPDIFRX support
.../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56 ++
sound/soc/stm/Kconfig | 10 +
sound/soc/stm/Makefile | 4 +
sound/soc/stm/stm32_spdifrx.c | 998 +++++++++++++++++++++
sound/soc/stm/stm32_spdifrx.h | 224 +++++
5 files changed, 1292 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
create mode 100644 sound/soc/stm/stm32_spdifrx.c
create mode 100644 sound/soc/stm/stm32_spdifrx.h
--
1.9.1
This adds documentation of device tree bindings for the
STM32 SPDIFRX interface.
Signed-off-by: olivier moysan <[email protected]>
---
.../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56 ++++++++++++++++++++++
1 file changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
new file mode 100644
index 0000000..33826f2
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
@@ -0,0 +1,56 @@
+STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
+
+The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
+IEC-60958 and IEC-61937.
+
+Required properties:
+ - compatible: should be "st,stm32h7-spdifrx"
+ - reg: cpu DAI IP base address and size
+ - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
+ - clock-names: must contain "kclk"
+ - interrupts: cpu DAI interrupt line
+ - dmas: DMA specifiers for audio data DMA and iec control flow DMA
+ See STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt
+ - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
+
+Optional properties:
+ - resets: Reference to a reset controller asserting the SPDIFRX
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+graph.txt.
+
+Example:
+spdifrx: spdifrx@40004000 {
+ compatible = "st,stm32h7-spdifrx";
+ reg = <0x40004000 0x400>;
+ clocks = <&rcc SPDIFRX_CK>;
+ clock-names = "kclk";
+ interrupts = <97>;
+ dmas = <&dmamux1 2 93 0x400 0x0>,
+ <&dmamux1 3 94 0x400 0x0>;
+ dma-names = "rx", "rx-ctrl";
+ pinctrl-0 = <&spdifrx_pins>;
+ pinctrl-names = "default";
+
+ spdifrx_port: port {
+ cpu_endpoint: endpoint {
+ remote-endpoint = <&codec_endpoint>;
+ };
+ };
+};
+
+spdif_in: spdif-in {
+ compatible = "linux,spdif-dir";
+
+ codec_port: port {
+ codec_endpoint: endpoint {
+ remote-endpoint = <&cpu_endpoint>;
+ };
+ };
+};
+
+soundcard {
+ compatible = "audio-graph-card";
+ dais = <&spdifrx_port>;
+};
--
1.9.1
Add SPDIFRX support to STM32.
Signed-off-by: olivier moysan <[email protected]>
---
sound/soc/stm/Kconfig | 10 +
sound/soc/stm/Makefile | 4 +
sound/soc/stm/stm32_spdifrx.c | 998 ++++++++++++++++++++++++++++++++++++++++++
sound/soc/stm/stm32_spdifrx.h | 224 ++++++++++
4 files changed, 1236 insertions(+)
create mode 100644 sound/soc/stm/stm32_spdifrx.c
create mode 100644 sound/soc/stm/stm32_spdifrx.h
diff --git a/sound/soc/stm/Kconfig b/sound/soc/stm/Kconfig
index d747993..45c05a3 100644
--- a/sound/soc/stm/Kconfig
+++ b/sound/soc/stm/Kconfig
@@ -9,4 +9,14 @@ config SND_SOC_STM32_SAI
help
Say Y if you want to enable SAI for STM32
+config SND_SOC_STM32_SPDIFRX
+ tristate "STM32 S/PDIF receiver (SPDIFRX) support"
+ depends on ARCH_STM32 || COMPILE_TEST
+ depends on SND_SOC
+ select SND_SOC_GENERIC_DMAENGINE_PCM
+ select REGMAP_MMIO
+ select SND_SOC_SPDIF
+ help
+ Say Y if you want to enable S/PDIF capture for STM32
+
endmenu
diff --git a/sound/soc/stm/Makefile b/sound/soc/stm/Makefile
index 386ce4b..c6a8e72 100644
--- a/sound/soc/stm/Makefile
+++ b/sound/soc/stm/Makefile
@@ -4,3 +4,7 @@ obj-$(CONFIG_SND_SOC_STM32_SAI) += snd-soc-stm32-sai-sub.o
snd-soc-stm32-sai-objs := stm32_sai.o
obj-$(CONFIG_SND_SOC_STM32_SAI) += snd-soc-stm32-sai.o
+
+# SPDIFRX
+snd-soc-stm32-spdifrx-objs := stm32_spdifrx.o
+obj-$(CONFIG_SND_SOC_STM32_SPDIFRX) += snd-soc-stm32-spdifrx.o
diff --git a/sound/soc/stm/stm32_spdifrx.c b/sound/soc/stm/stm32_spdifrx.c
new file mode 100644
index 0000000..4e4250b
--- /dev/null
+++ b/sound/soc/stm/stm32_spdifrx.c
@@ -0,0 +1,998 @@
+/*
+ * STM32 ALSA SoC Digital Audio Interface (SPDIF-rx) driver.
+ *
+ * Copyright (C) 2017, STMicroelectronics - All Rights Reserved
+ * Author(s): Olivier Moysan <[email protected]> for STMicroelectronics.
+ *
+ * License terms: GPL V2.0.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
+ * details.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <sound/dmaengine_pcm.h>
+#include <sound/pcm_params.h>
+
+/* SPDIF-rx Register Map */
+#define STM32_SPDIFRX_CR 0x00
+#define STM32_SPDIFRX_IMR 0x04
+#define STM32_SPDIFRX_SR 0x08
+#define STM32_SPDIFRX_IFCR 0x0C
+#define STM32_SPDIFRX_DR 0x10
+#define STM32_SPDIFRX_CSR 0x14
+#define STM32_SPDIFRX_DIR 0x18
+
+/* Bit definition for SPDIF_CR register */
+#define SPDIFRX_CR_SPDIFEN_SHIFT 0
+#define SPDIFRX_CR_SPDIFEN_MASK GENMASK(1, SPDIFRX_CR_SPDIFEN_SHIFT)
+#define SPDIFRX_CR_SPDIFENSET(x) ((x) << SPDIFRX_CR_SPDIFEN_SHIFT)
+
+#define SPDIFRX_CR_RXDMAEN BIT(2)
+#define SPDIFRX_CR_RXSTEO BIT(3)
+
+#define SPDIFRX_CR_DRFMT_SHIFT 4
+#define SPDIFRX_CR_DRFMT_MASK GENMASK(5, SPDIFRX_CR_DRFMT_SHIFT)
+#define SPDIFRX_CR_DRFMTSET(x) ((x) << SPDIFRX_CR_DRFMT_SHIFT)
+
+#define SPDIFRX_CR_PMSK BIT(6)
+#define SPDIFRX_CR_VMSK BIT(7)
+#define SPDIFRX_CR_CUMSK BIT(8)
+#define SPDIFRX_CR_PTMSK BIT(9)
+#define SPDIFRX_CR_CBDMAEN BIT(10)
+#define SPDIFRX_CR_CHSEL_SHIFT 11
+#define SPDIFRX_CR_CHSEL BIT(SPDIFRX_CR_CHSEL_SHIFT)
+
+#define SPDIFRX_CR_NBTR_SHIFT 12
+#define SPDIFRX_CR_NBTR_MASK GENMASK(13, SPDIFRX_CR_NBTR_SHIFT)
+#define SPDIFRX_CR_NBTRSET(x) ((x) << SPDIFRX_CR_NBTR_SHIFT)
+
+#define SPDIFRX_CR_WFA BIT(14)
+
+#define SPDIFRX_CR_INSEL_SHIFT 16
+#define SPDIFRX_CR_INSEL_MASK GENMASK(18, PDIFRX_CR_INSEL_SHIFT)
+#define SPDIFRX_CR_INSELSET(x) ((x) << SPDIFRX_CR_INSEL_SHIFT)
+
+#define SPDIFRX_CR_CKSEN_SHIFT 20
+#define SPDIFRX_CR_CKSEN BIT(20)
+#define SPDIFRX_CR_CKSBKPEN BIT(21)
+
+/* Bit definition for SPDIFRX_IMR register */
+#define SPDIFRX_IMR_RXNEI BIT(0)
+#define SPDIFRX_IMR_CSRNEIE BIT(1)
+#define SPDIFRX_IMR_PERRIE BIT(2)
+#define SPDIFRX_IMR_OVRIE BIT(3)
+#define SPDIFRX_IMR_SBLKIE BIT(4)
+#define SPDIFRX_IMR_SYNCDIE BIT(5)
+#define SPDIFRX_IMR_IFEIE BIT(6)
+
+#define SPDIFRX_XIMR_MASK GENMASK(6, 0)
+
+/* Bit definition for SPDIFRX_SR register */
+#define SPDIFRX_SR_RXNE BIT(0)
+#define SPDIFRX_SR_CSRNE BIT(1)
+#define SPDIFRX_SR_PERR BIT(2)
+#define SPDIFRX_SR_OVR BIT(3)
+#define SPDIFRX_SR_SBD BIT(4)
+#define SPDIFRX_SR_SYNCD BIT(5)
+#define SPDIFRX_SR_FERR BIT(6)
+#define SPDIFRX_SR_SERR BIT(7)
+#define SPDIFRX_SR_TERR BIT(8)
+
+#define SPDIFRX_SR_WIDTH5_SHIFT 16
+#define SPDIFRX_SR_WIDTH5_MASK GENMASK(30, PDIFRX_SR_WIDTH5_SHIFT)
+#define SPDIFRX_SR_WIDTH5SET(x) ((x) << SPDIFRX_SR_WIDTH5_SHIFT)
+
+/* Bit definition for SPDIFRX_IFCR register */
+#define SPDIFRX_IFCR_PERRCF BIT(2)
+#define SPDIFRX_IFCR_OVRCF BIT(3)
+#define SPDIFRX_IFCR_SBDCF BIT(4)
+#define SPDIFRX_IFCR_SYNCDCF BIT(5)
+
+#define SPDIFRX_XIFCR_MASK GENMASK(5, 2)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b00) */
+#define SPDIFRX_DR0_DR_SHIFT 0
+#define SPDIFRX_DR0_DR_MASK GENMASK(23, SPDIFRX_DR0_DR_SHIFT)
+#define SPDIFRX_DR0_DRSET(x) ((x) << SPDIFRX_DR0_DR_SHIFT)
+
+#define SPDIFRX_DR0_PE BIT(24)
+
+#define SPDIFRX_DR0_V BIT(25)
+#define SPDIFRX_DR0_U BIT(26)
+#define SPDIFRX_DR0_C BIT(27)
+
+#define SPDIFRX_DR0_PT_SHIFT 28
+#define SPDIFRX_DR0_PT_MASK GENMASK(29, SPDIFRX_DR0_PT_SHIFT)
+#define SPDIFRX_DR0_PTSET(x) ((x) << SPDIFRX_DR0_PT_SHIFT)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b01) */
+#define SPDIFRX_DR1_PE BIT(0)
+#define SPDIFRX_DR1_V BIT(1)
+#define SPDIFRX_DR1_U BIT(2)
+#define SPDIFRX_DR1_C BIT(3)
+
+#define SPDIFRX_DR1_PT_SHIFT 4
+#define SPDIFRX_DR1_PT_MASK GENMASK(5, SPDIFRX_DR1_PT_SHIFT)
+#define SPDIFRX_DR1_PTSET(x) ((x) << SPDIFRX_DR1_PT_SHIFT)
+
+#define SPDIFRX_DR1_DR_SHIFT 8
+#define SPDIFRX_DR1_DR_MASK GENMASK(31, SPDIFRX_DR1_DR_SHIFT)
+#define SPDIFRX_DR1_DRSET(x) ((x) << SPDIFRX_DR1_DR_SHIFT)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b10) */
+#define SPDIFRX_DR1_DRNL1_SHIFT 0
+#define SPDIFRX_DR1_DRNL1_MASK GENMASK(15, SPDIFRX_DR1_DRNL1_SHIFT)
+#define SPDIFRX_DR1_DRNL1SET(x) ((x) << SPDIFRX_DR1_DRNL1_SHIFT)
+
+#define SPDIFRX_DR1_DRNL2_SHIFT 16
+#define SPDIFRX_DR1_DRNL2_MASK GENMASK(31, SPDIFRX_DR1_DRNL2_SHIFT)
+#define SPDIFRX_DR1_DRNL2SET(x) ((x) << SPDIFRX_DR1_DRNL2_SHIFT)
+
+/* Bit definition for SPDIFRX_CSR register */
+#define SPDIFRX_CSR_USR_SHIFT 0
+#define SPDIFRX_CSR_USR_MASK GENMASK(15, SPDIFRX_CSR_USR_SHIFT)
+#define SPDIFRX_CSR_USRGET(x) (((x) & SPDIFRX_CSR_USR_MASK)\
+ >> SPDIFRX_CSR_USR_SHIFT)
+
+#define SPDIFRX_CSR_CS_SHIFT 16
+#define SPDIFRX_CSR_CS_MASK GENMASK(23, SPDIFRX_CSR_CS_SHIFT)
+#define SPDIFRX_CSR_CSGET(x) (((x) & SPDIFRX_CSR_CS_MASK)\
+ >> SPDIFRX_CSR_CS_SHIFT)
+
+#define SPDIFRX_CSR_SOB BIT(24)
+
+/* Bit definition for SPDIFRX_DIR register */
+#define SPDIFRX_DIR_THI_SHIFT 0
+#define SPDIFRX_DIR_THI_MASK GENMASK(12, SPDIFRX_DIR_THI_SHIFT)
+#define SPDIFRX_DIR_THI_SET(x) ((x) << SPDIFRX_DIR_THI_SHIFT)
+
+#define SPDIFRX_DIR_TLO_SHIFT 16
+#define SPDIFRX_DIR_TLO_MASK GENMASK(28, SPDIFRX_DIR_TLO_SHIFT)
+#define SPDIFRX_DIR_TLO_SET(x) ((x) << SPDIFRX_DIR_TLO_SHIFT)
+
+#define SPDIFRX_SPDIFEN_DISABLE 0x0
+#define SPDIFRX_SPDIFEN_SYNC 0x1
+#define SPDIFRX_SPDIFEN_ENABLE 0x3
+
+#define SPDIFRX_IN1 0x1
+#define SPDIFRX_IN2 0x2
+#define SPDIFRX_IN3 0x3
+#define SPDIFRX_IN4 0x4
+#define SPDIFRX_IN5 0x5
+#define SPDIFRX_IN6 0x6
+#define SPDIFRX_IN7 0x7
+#define SPDIFRX_IN8 0x8
+
+#define SPDIFRX_NBTR_NONE 0x0
+#define SPDIFRX_NBTR_3 0x1
+#define SPDIFRX_NBTR_15 0x2
+#define SPDIFRX_NBTR_63 0x3
+
+#define SPDIFRX_DRFMT_RIGHT 0x0
+#define SPDIFRX_DRFMT_LEFT 0x1
+#define SPDIFRX_DRFMT_PACKED 0x2
+
+/* 192 CS bits in S/PDIF frame. i.e 24 CS bytes */
+#define SPDIFRX_CS_BYTES_NB 24
+#define SPDIFRX_UB_BYTES_NB 48
+
+/*
+ * CSR register is retrieved as a 32 bits word
+ * It contains 1 channel status byte and 2 user data bytes
+ * 2 S/PDIF frames are acquired to get all CS/UB bits
+ */
+#define SPDIFRX_CSR_BUF_LENGTH (SPDIFRX_CS_BYTES_NB * 4 * 2)
+
+/**
+ * struct stm32_spdifrx_data - private data of SPDIFRX
+ * @pdev: device data pointer
+ * @base: mmio register base virtual address
+ * @regmap: SPDIFRX register map pointer
+ * @regmap_conf: SPDIFRX register map configuration pointer
+ * @cs_completion: channel status retrieving completion
+ * @kclk: kernel clock feeding the SPDIFRX clock generator
+ * @dma_params: dma configuration data for rx channel
+ * @substream: PCM substream data pointer
+ * @dmab: dma buffer info pointer
+ * @ctrl_chan: dma channel for S/PDIF control bits
+ * @desc:dma async transaction descriptor
+ * @slave_config: dma slave channel runtime config pointer
+ * @phys_addr: SPDIFRX registers physical base address
+ * @lock: synchronization enabling lock
+ * @cs: channel status buffer
+ * @ub: user data buffer
+ * @irq: SPDIFRX interrupt line
+ * @refcount: keep count of opened DMA channels
+ */
+struct stm32_spdifrx_data {
+ struct platform_device *pdev;
+ void __iomem *base;
+ struct regmap *regmap;
+ const struct regmap_config *regmap_conf;
+ struct completion cs_completion;
+ struct clk *kclk;
+ struct snd_dmaengine_dai_dma_data dma_params;
+ struct snd_pcm_substream *substream;
+ struct snd_dma_buffer *dmab;
+ struct dma_chan *ctrl_chan;
+ struct dma_async_tx_descriptor *desc;
+ struct dma_slave_config slave_config;
+ dma_addr_t phys_addr;
+ spinlock_t lock; /* Sync enabling lock */
+ unsigned char cs[SPDIFRX_CS_BYTES_NB];
+ unsigned char ub[SPDIFRX_UB_BYTES_NB];
+ int irq;
+ int refcount;
+};
+
+static void stm32_spdifrx_dma_complete(void *data)
+{
+ struct stm32_spdifrx_data *spdifrx = (struct stm32_spdifrx_data *)data;
+ struct platform_device *pdev = spdifrx->pdev;
+ u32 *p_start = (u32 *)spdifrx->dmab->area;
+ u32 *p_end = p_start + (2 * SPDIFRX_CS_BYTES_NB) - 1;
+ u32 *ptr = p_start;
+ u16 *ub_ptr = (short *)spdifrx->ub;
+ int i = 0;
+
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_CBDMAEN,
+ (unsigned int)~SPDIFRX_CR_CBDMAEN);
+
+ if (!spdifrx->dmab->area)
+ return;
+
+ while (ptr <= p_end) {
+ if (*ptr & SPDIFRX_CSR_SOB)
+ break;
+ ptr++;
+ }
+
+ if (ptr > p_end) {
+ dev_err(&pdev->dev, "Start of S/PDIF block not found\n");
+ return;
+ }
+
+ while (i < SPDIFRX_CS_BYTES_NB) {
+ spdifrx->cs[i] = (unsigned char)SPDIFRX_CSR_CSGET(*ptr);
+ *ub_ptr++ = SPDIFRX_CSR_USRGET(*ptr++);
+ if (ptr > p_end) {
+ dev_err(&pdev->dev, "Failed to get channel status\n");
+ return;
+ }
+ i++;
+ }
+
+ complete(&spdifrx->cs_completion);
+}
+
+static int stm32_spdifrx_dma_ctrl_start(struct stm32_spdifrx_data *spdifrx)
+{
+ dma_cookie_t cookie;
+ int err;
+
+ spdifrx->desc = dmaengine_prep_slave_single(spdifrx->ctrl_chan,
+ spdifrx->dmab->addr,
+ SPDIFRX_CSR_BUF_LENGTH,
+ DMA_DEV_TO_MEM,
+ DMA_CTRL_ACK);
+ if (!spdifrx->desc)
+ return -EINVAL;
+
+ spdifrx->desc->callback = stm32_spdifrx_dma_complete;
+ spdifrx->desc->callback_param = spdifrx;
+ cookie = dmaengine_submit(spdifrx->desc);
+ err = dma_submit_error(cookie);
+ if (err)
+ return -EINVAL;
+
+ dma_async_issue_pending(spdifrx->ctrl_chan);
+
+ return 0;
+}
+
+static void stm32_spdifrx_dma_ctrl_stop(struct stm32_spdifrx_data *spdifrx)
+{
+ dmaengine_terminate_async(spdifrx->ctrl_chan);
+}
+
+static int stm32_spdifrx_start_sync(struct stm32_spdifrx_data *spdifrx)
+{
+ int cr, cr_mask, imr, ret;
+
+ /* Enable IRQs */
+ imr = SPDIFRX_IMR_IFEIE | SPDIFRX_IMR_SYNCDIE | SPDIFRX_IMR_PERRIE;
+ ret = regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_IMR, imr, imr);
+ if (ret)
+ return ret;
+
+ spin_lock(&spdifrx->lock);
+
+ spdifrx->refcount++;
+
+ regmap_read(spdifrx->regmap, STM32_SPDIFRX_CR, &cr);
+
+ if (!(cr & SPDIFRX_CR_SPDIFEN_MASK)) {
+ /*
+ * Start sync if SPDIFRX is still in idle state.
+ * SPDIFRX reception enabled when sync done
+ */
+ dev_dbg(&spdifrx->pdev->dev, "start synchronization\n");
+
+ /*
+ * SPDIFRX configuration:
+ * Wait for activity before starting sync process. This avoid
+ * to issue sync errors when spdif signal is missing on input.
+ * Preamble, CS, user, validity and parity error bits not copied
+ * to DR register.
+ */
+ cr = SPDIFRX_CR_WFA | SPDIFRX_CR_PMSK | SPDIFRX_CR_VMSK |
+ SPDIFRX_CR_CUMSK | SPDIFRX_CR_PTMSK | SPDIFRX_CR_RXSTEO;
+ cr_mask = cr;
+
+ cr |= SPDIFRX_CR_SPDIFENSET(SPDIFRX_SPDIFEN_SYNC);
+ cr_mask |= SPDIFRX_CR_SPDIFEN_MASK;
+ ret = regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ cr_mask, cr);
+ if (ret < 0)
+ dev_err(&spdifrx->pdev->dev,
+ "Failed to start synchronization\n");
+ }
+
+ spin_unlock(&spdifrx->lock);
+
+ return ret;
+}
+
+static void stm32_spdifrx_stop(struct stm32_spdifrx_data *spdifrx)
+{
+ int cr, cr_mask, reg;
+
+ spin_lock(&spdifrx->lock);
+
+ if (--spdifrx->refcount) {
+ spin_unlock(&spdifrx->lock);
+ return;
+ }
+
+ cr = SPDIFRX_CR_SPDIFENSET(SPDIFRX_SPDIFEN_DISABLE);
+ cr_mask = SPDIFRX_CR_SPDIFEN_MASK | SPDIFRX_CR_RXDMAEN;
+
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR, cr_mask, cr);
+
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_IMR,
+ SPDIFRX_XIMR_MASK, 0);
+
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_IFCR,
+ SPDIFRX_XIFCR_MASK, SPDIFRX_XIFCR_MASK);
+
+ /* dummy read to clear CSRNE and RXNE in status register */
+ regmap_read(spdifrx->regmap, STM32_SPDIFRX_DR, ®);
+ regmap_read(spdifrx->regmap, STM32_SPDIFRX_CSR, ®);
+
+ spin_unlock(&spdifrx->lock);
+}
+
+static int stm32_spdifrx_dma_ctrl_register(struct device *dev,
+ struct stm32_spdifrx_data *spdifrx)
+{
+ int ret;
+
+ spdifrx->dmab = devm_kzalloc(dev, sizeof(struct snd_dma_buffer),
+ GFP_KERNEL);
+ if (!spdifrx->dmab)
+ return -ENOMEM;
+
+ spdifrx->dmab->dev.type = SNDRV_DMA_TYPE_DEV_IRAM;
+ spdifrx->dmab->dev.dev = dev;
+ ret = snd_dma_alloc_pages(spdifrx->dmab->dev.type, dev,
+ SPDIFRX_CSR_BUF_LENGTH, spdifrx->dmab);
+ if (ret < 0) {
+ dev_err(dev, "snd_dma_alloc_pages returned error %d\n", ret);
+ return ret;
+ }
+
+ spdifrx->ctrl_chan = dma_request_chan(dev, "rx-ctrl");
+ if (!spdifrx->ctrl_chan) {
+ dev_err(dev, "dma_request_slave_channel failed\n");
+ return -EINVAL;
+ }
+
+ spdifrx->slave_config.direction = DMA_DEV_TO_MEM;
+ spdifrx->slave_config.src_addr = (dma_addr_t)(spdifrx->phys_addr +
+ STM32_SPDIFRX_CSR);
+ spdifrx->slave_config.dst_addr = spdifrx->dmab->addr;
+ spdifrx->slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ spdifrx->slave_config.src_maxburst = 1;
+
+ ret = dmaengine_slave_config(spdifrx->ctrl_chan,
+ &spdifrx->slave_config);
+ if (ret < 0) {
+ dev_err(dev, "dmaengine_slave_config returned error %d\n", ret);
+ dma_release_channel(spdifrx->ctrl_chan);
+ spdifrx->ctrl_chan = NULL;
+ }
+
+ return ret;
+};
+
+static const char * const spdifrx_enum_input[] = {
+ "in0", "in1", "in2", "in3"
+};
+
+/* By default CS bits are retrieved from channel A */
+static const char * const spdifrx_enum_cs_channel[] = {
+ "A", "B"
+};
+
+static SOC_ENUM_SINGLE_DECL(ctrl_enum_input,
+ STM32_SPDIFRX_CR, SPDIFRX_CR_INSEL_SHIFT,
+ spdifrx_enum_input);
+
+static SOC_ENUM_SINGLE_DECL(ctrl_enum_cs_channel,
+ STM32_SPDIFRX_CR, SPDIFRX_CR_CHSEL_SHIFT,
+ spdifrx_enum_cs_channel);
+
+static int stm32_spdifrx_info(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958;
+ uinfo->count = 1;
+
+ return 0;
+}
+
+static int stm32_spdifrx_ub_info(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958;
+ uinfo->count = 1;
+
+ return 0;
+}
+
+static int stm32_spdifrx_get_ctrl_data(struct stm32_spdifrx_data *spdifrx)
+{
+ int ret = 0;
+
+ memset(spdifrx->cs, 0, SPDIFRX_CS_BYTES_NB);
+ memset(spdifrx->ub, 0, SPDIFRX_UB_BYTES_NB);
+
+ ret = stm32_spdifrx_dma_ctrl_start(spdifrx);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_prepare_enable(spdifrx->kclk);
+ if (ret) {
+ dev_err(&spdifrx->pdev->dev, "Enable kclk failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_CBDMAEN, SPDIFRX_CR_CBDMAEN);
+ if (ret < 0)
+ goto end;
+
+ ret = stm32_spdifrx_start_sync(spdifrx);
+ if (ret < 0)
+ goto end;
+
+ if (wait_for_completion_interruptible_timeout(&spdifrx->cs_completion,
+ msecs_to_jiffies(100))
+ <= 0) {
+ dev_err(&spdifrx->pdev->dev, "Failed to get control data\n");
+ ret = -EAGAIN;
+ }
+
+ stm32_spdifrx_stop(spdifrx);
+ stm32_spdifrx_dma_ctrl_stop(spdifrx);
+
+end:
+ clk_disable_unprepare(spdifrx->kclk);
+
+ return ret;
+}
+
+static int stm32_spdifrx_capture_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dai *cpu_dai = snd_kcontrol_chip(kcontrol);
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+
+ stm32_spdifrx_get_ctrl_data(spdifrx);
+
+ ucontrol->value.iec958.status[0] = spdifrx->cs[0];
+ ucontrol->value.iec958.status[1] = spdifrx->cs[1];
+ ucontrol->value.iec958.status[2] = spdifrx->cs[2];
+ ucontrol->value.iec958.status[3] = spdifrx->cs[3];
+ ucontrol->value.iec958.status[4] = spdifrx->cs[4];
+
+ return 0;
+}
+
+static int stm32_spdif_user_bits_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dai *cpu_dai = snd_kcontrol_chip(kcontrol);
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+
+ stm32_spdifrx_get_ctrl_data(spdifrx);
+
+ ucontrol->value.iec958.status[0] = spdifrx->ub[0];
+ ucontrol->value.iec958.status[1] = spdifrx->ub[1];
+ ucontrol->value.iec958.status[2] = spdifrx->ub[2];
+ ucontrol->value.iec958.status[3] = spdifrx->ub[3];
+ ucontrol->value.iec958.status[4] = spdifrx->ub[4];
+
+ return 0;
+}
+
+static struct snd_kcontrol_new stm32_spdifrx_iec_ctrls[] = {
+ /* Channel status control */
+ {
+ .iface = SNDRV_CTL_ELEM_IFACE_PCM,
+ .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, DEFAULT),
+ .access = SNDRV_CTL_ELEM_ACCESS_READ |
+ SNDRV_CTL_ELEM_ACCESS_VOLATILE,
+ .info = stm32_spdifrx_info,
+ .get = stm32_spdifrx_capture_get,
+ },
+ /* User bits control */
+ {
+ .iface = SNDRV_CTL_ELEM_IFACE_PCM,
+ .name = "IEC958 User Bit Capture Default",
+ .access = SNDRV_CTL_ELEM_ACCESS_READ |
+ SNDRV_CTL_ELEM_ACCESS_VOLATILE,
+ .info = stm32_spdifrx_ub_info,
+ .get = stm32_spdif_user_bits_get,
+ },
+};
+
+static struct snd_kcontrol_new stm32_spdifrx_ctrls[] = {
+ SOC_ENUM("SPDIFRX input", ctrl_enum_input),
+ SOC_ENUM("SPDIFRX CS channel", ctrl_enum_cs_channel),
+};
+
+static int stm32_spdifrx_dai_register_ctrls(struct snd_soc_dai *cpu_dai)
+{
+ int ret;
+
+ ret = snd_soc_add_dai_controls(cpu_dai, stm32_spdifrx_iec_ctrls,
+ ARRAY_SIZE(stm32_spdifrx_iec_ctrls));
+ if (ret < 0)
+ return ret;
+
+ return snd_soc_add_component_controls(cpu_dai->component,
+ stm32_spdifrx_ctrls,
+ ARRAY_SIZE(stm32_spdifrx_ctrls));
+}
+
+static int stm32_spdifrx_dai_probe(struct snd_soc_dai *cpu_dai)
+{
+ struct stm32_spdifrx_data *spdifrx = dev_get_drvdata(cpu_dai->dev);
+
+ spdifrx->dma_params.addr = (dma_addr_t)(spdifrx->phys_addr +
+ STM32_SPDIFRX_DR);
+ spdifrx->dma_params.maxburst = 1;
+
+ snd_soc_dai_init_dma_data(cpu_dai, NULL, &spdifrx->dma_params);
+
+ return stm32_spdifrx_dai_register_ctrls(cpu_dai);
+}
+
+static bool stm32_spdifrx_readable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case STM32_SPDIFRX_CR:
+ case STM32_SPDIFRX_IMR:
+ case STM32_SPDIFRX_SR:
+ case STM32_SPDIFRX_IFCR:
+ case STM32_SPDIFRX_DR:
+ case STM32_SPDIFRX_CSR:
+ case STM32_SPDIFRX_DIR:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool stm32_spdifrx_volatile_reg(struct device *dev, unsigned int reg)
+{
+ if (reg == STM32_SPDIFRX_DR)
+ return true;
+
+ return false;
+}
+
+static bool stm32_spdifrx_writeable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case STM32_SPDIFRX_CR:
+ case STM32_SPDIFRX_IMR:
+ case STM32_SPDIFRX_IFCR:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct regmap_config stm32_h7_spdifrx_regmap_conf = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = STM32_SPDIFRX_DIR,
+ .readable_reg = stm32_spdifrx_readable_reg,
+ .volatile_reg = stm32_spdifrx_volatile_reg,
+ .writeable_reg = stm32_spdifrx_writeable_reg,
+ .fast_io = true,
+};
+
+static irqreturn_t stm32_spdifrx_isr(int irq, void *devid)
+{
+ struct stm32_spdifrx_data *spdifrx = (struct stm32_spdifrx_data *)devid;
+ struct snd_pcm_substream *substream = spdifrx->substream;
+ struct platform_device *pdev = spdifrx->pdev;
+ unsigned int cr, mask, sr, imr;
+ unsigned int flags;
+ int err = 0, err_xrun = 0;
+
+ regmap_read(spdifrx->regmap, STM32_SPDIFRX_SR, &sr);
+ regmap_read(spdifrx->regmap, STM32_SPDIFRX_IMR, &imr);
+
+ mask = imr & SPDIFRX_XIMR_MASK;
+ /* SERR, TERR, FERR IRQs are generated if IFEIE is set */
+ if (mask & SPDIFRX_IMR_IFEIE)
+ mask |= (SPDIFRX_IMR_IFEIE << 1) | (SPDIFRX_IMR_IFEIE << 2);
+
+ flags = sr & mask;
+ if (!flags) {
+ dev_err(&pdev->dev, "Unexpected IRQ. rflags=%#x, imr=%#x\n",
+ sr, imr);
+ return IRQ_NONE;
+ }
+
+ /* Clear IRQs */
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_IFCR,
+ SPDIFRX_XIFCR_MASK, flags);
+
+ if (flags & SPDIFRX_SR_PERR) {
+ dev_dbg(&pdev->dev, "Parity error\n");
+ err_xrun = 1;
+ }
+
+ if (flags & SPDIFRX_SR_OVR) {
+ dev_dbg(&pdev->dev, "Overrun error\n");
+ err_xrun = 1;
+ }
+
+ if (flags & SPDIFRX_SR_SBD)
+ dev_dbg(&pdev->dev, "Synchronization block detected\n");
+
+ if (flags & SPDIFRX_SR_SYNCD) {
+ dev_dbg(&pdev->dev, "Synchronization done\n");
+
+ /* Enable spdifrx */
+ cr = SPDIFRX_CR_SPDIFENSET(SPDIFRX_SPDIFEN_ENABLE);
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_SPDIFEN_MASK, cr);
+ }
+
+ if (flags & SPDIFRX_SR_FERR) {
+ dev_dbg(&pdev->dev, "Frame error\n");
+ err = 1;
+ }
+
+ if (flags & SPDIFRX_SR_SERR) {
+ dev_dbg(&pdev->dev, "Synchronization error\n");
+ err = 1;
+ }
+
+ if (flags & SPDIFRX_SR_TERR) {
+ dev_dbg(&pdev->dev, "Timeout error\n");
+ err = 1;
+ }
+
+ if (err) {
+ /* SPDIFRX in STATE_STOP. Disable SPDIFRX to clear errors */
+ cr = SPDIFRX_CR_SPDIFENSET(SPDIFRX_SPDIFEN_DISABLE);
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_SPDIFEN_MASK, cr);
+
+ if (substream)
+ snd_pcm_stop(substream, SNDRV_PCM_STATE_DISCONNECTED);
+
+ return IRQ_HANDLED;
+ }
+
+ if (err_xrun && substream)
+ snd_pcm_stop_xrun(substream);
+
+ return IRQ_HANDLED;
+}
+
+static int stm32_spdifrx_startup(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+ int ret;
+
+ spdifrx->substream = substream;
+
+ ret = clk_prepare_enable(spdifrx->kclk);
+ if (ret)
+ dev_err(&spdifrx->pdev->dev, "Enable kclk failed: %d\n", ret);
+
+ return ret;
+}
+
+static int stm32_spdifrx_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+ int data_size = params_width(params);
+ int fmt;
+
+ switch (data_size) {
+ case 16:
+ fmt = SPDIFRX_DRFMT_PACKED;
+ spdifrx->dma_params.addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ break;
+ case 32:
+ fmt = SPDIFRX_DRFMT_LEFT;
+ spdifrx->dma_params.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ break;
+ default:
+ dev_err(&spdifrx->pdev->dev, "Unexpected data format\n");
+ return -EINVAL;
+ }
+
+ snd_soc_dai_init_dma_data(cpu_dai, NULL, &spdifrx->dma_params);
+
+ return regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_DRFMT_MASK,
+ SPDIFRX_CR_DRFMTSET(fmt));
+}
+
+static int stm32_spdifrx_trigger(struct snd_pcm_substream *substream, int cmd,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+ int ret = 0;
+
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ case SNDRV_PCM_TRIGGER_RESUME:
+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_IMR,
+ SPDIFRX_IMR_OVRIE, SPDIFRX_IMR_OVRIE);
+
+ regmap_update_bits(spdifrx->regmap, STM32_SPDIFRX_CR,
+ SPDIFRX_CR_RXDMAEN, SPDIFRX_CR_RXDMAEN);
+
+ ret = stm32_spdifrx_start_sync(spdifrx);
+ break;
+ case SNDRV_PCM_TRIGGER_SUSPEND:
+ case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+ case SNDRV_PCM_TRIGGER_STOP:
+ stm32_spdifrx_stop(spdifrx);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+static void stm32_spdifrx_shutdown(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *cpu_dai)
+{
+ struct stm32_spdifrx_data *spdifrx = snd_soc_dai_get_drvdata(cpu_dai);
+
+ spdifrx->substream = NULL;
+ clk_disable_unprepare(spdifrx->kclk);
+}
+
+static const struct snd_soc_dai_ops stm32_spdifrx_pcm_dai_ops = {
+ .startup = stm32_spdifrx_startup,
+ .hw_params = stm32_spdifrx_hw_params,
+ .trigger = stm32_spdifrx_trigger,
+ .shutdown = stm32_spdifrx_shutdown,
+};
+
+static struct snd_soc_dai_driver stm32_spdifrx_dai[] = {
+ {
+ .name = "spdifrx-capture-cpu-dai",
+ .probe = stm32_spdifrx_dai_probe,
+ .capture = {
+ .stream_name = "CPU-Capture",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = SNDRV_PCM_RATE_8000_192000,
+ .formats = SNDRV_PCM_FMTBIT_S32_LE |
+ SNDRV_PCM_FMTBIT_S16_LE,
+ },
+ .ops = &stm32_spdifrx_pcm_dai_ops,
+ }
+};
+
+static const struct snd_pcm_hardware stm32_spdifrx_pcm_hw = {
+ .info = SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_MMAP,
+ .buffer_bytes_max = 8 * PAGE_SIZE,
+ .period_bytes_max = 2048, /* MDMA constraint */
+ .periods_min = 2,
+ .periods_max = 8,
+};
+
+static const struct snd_soc_component_driver stm32_spdifrx_component = {
+ .name = "stm32-spdifrx",
+};
+
+static const struct snd_dmaengine_pcm_config stm32_spdifrx_pcm_config = {
+ .pcm_hardware = &stm32_spdifrx_pcm_hw,
+ .prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config,
+};
+
+static const struct of_device_id stm32_spdifrx_ids[] = {
+ {
+ .compatible = "st,stm32h7-spdifrx",
+ .data = &stm32_h7_spdifrx_regmap_conf
+ },
+ {}
+};
+
+static int stm_spdifrx_parse_of(struct platform_device *pdev,
+ struct stm32_spdifrx_data *spdifrx)
+{
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *of_id;
+ struct resource *res;
+
+ if (!np)
+ return -ENODEV;
+
+ of_id = of_match_device(stm32_spdifrx_ids, &pdev->dev);
+ if (of_id)
+ spdifrx->regmap_conf =
+ (const struct regmap_config *)of_id->data;
+ else
+ return -EINVAL;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ spdifrx->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spdifrx->base))
+ return PTR_ERR(spdifrx->base);
+
+ spdifrx->phys_addr = res->start;
+
+ spdifrx->kclk = devm_clk_get(&pdev->dev, "kclk");
+ if (IS_ERR(spdifrx->kclk)) {
+ dev_err(&pdev->dev, "Could not get kclk\n");
+ return PTR_ERR(spdifrx->kclk);
+ }
+
+ spdifrx->irq = platform_get_irq(pdev, 0);
+ if (spdifrx->irq < 0) {
+ dev_err(&pdev->dev, "No irq for node %s\n", pdev->name);
+ return spdifrx->irq;
+ }
+
+ return 0;
+}
+
+static int stm32_spdifrx_probe(struct platform_device *pdev)
+{
+ struct stm32_spdifrx_data *spdifrx;
+ struct reset_control *rst;
+ const struct snd_dmaengine_pcm_config *pcm_config = NULL;
+ int ret;
+
+ spdifrx = devm_kzalloc(&pdev->dev, sizeof(*spdifrx), GFP_KERNEL);
+ if (!spdifrx)
+ return -ENOMEM;
+
+ spdifrx->pdev = pdev;
+ init_completion(&spdifrx->cs_completion);
+ spin_lock_init(&spdifrx->lock);
+
+ platform_set_drvdata(pdev, spdifrx);
+
+ ret = stm_spdifrx_parse_of(pdev, spdifrx);
+ if (ret)
+ return ret;
+
+ spdifrx->regmap = devm_regmap_init_mmio_clk(&pdev->dev, "kclk",
+ spdifrx->base,
+ spdifrx->regmap_conf);
+ if (IS_ERR(spdifrx->regmap)) {
+ dev_err(&pdev->dev, "Regmap init failed\n");
+ return PTR_ERR(spdifrx->regmap);
+ }
+
+ ret = devm_request_irq(&pdev->dev, spdifrx->irq, stm32_spdifrx_isr, 0,
+ dev_name(&pdev->dev), spdifrx);
+ if (ret) {
+ dev_err(&pdev->dev, "IRQ request returned %d\n", ret);
+ return ret;
+ }
+
+ rst = devm_reset_control_get(&pdev->dev, NULL);
+ if (!IS_ERR(rst)) {
+ reset_control_assert(rst);
+ udelay(2);
+ reset_control_deassert(rst);
+ }
+
+ ret = devm_snd_soc_register_component(&pdev->dev,
+ &stm32_spdifrx_component,
+ stm32_spdifrx_dai,
+ ARRAY_SIZE(stm32_spdifrx_dai));
+ if (ret)
+ return ret;
+
+ ret = stm32_spdifrx_dma_ctrl_register(&pdev->dev, spdifrx);
+ if (ret)
+ goto error;
+
+ pcm_config = &stm32_spdifrx_pcm_config;
+ ret = devm_snd_dmaengine_pcm_register(&pdev->dev, pcm_config, 0);
+ if (ret) {
+ dev_err(&pdev->dev, "PCM DMA register returned %d\n", ret);
+ goto error;
+ }
+
+ return 0;
+
+error:
+ if (spdifrx->ctrl_chan)
+ dma_release_channel(spdifrx->ctrl_chan);
+ if (spdifrx->dmab)
+ snd_dma_free_pages(spdifrx->dmab);
+
+ return ret;
+}
+
+static int stm32_spdifrx_remove(struct platform_device *pdev)
+{
+ struct stm32_spdifrx_data *spdifrx = platform_get_drvdata(pdev);
+
+ if (spdifrx->ctrl_chan)
+ dma_release_channel(spdifrx->ctrl_chan);
+
+ if (spdifrx->dmab)
+ snd_dma_free_pages(spdifrx->dmab);
+
+ return 0;
+}
+
+MODULE_DEVICE_TABLE(of, stm32_spdifrx_ids);
+
+static struct platform_driver stm32_spdifrx_driver = {
+ .driver = {
+ .name = "st,stm32-spdifrx",
+ .of_match_table = stm32_spdifrx_ids,
+ },
+ .probe = stm32_spdifrx_probe,
+ .remove = stm32_spdifrx_remove,
+};
+
+module_platform_driver(stm32_spdifrx_driver);
+
+MODULE_DESCRIPTION("STM32 Soc spdifrx Interface");
+MODULE_AUTHOR("Olivier Moysan, <[email protected]>");
+MODULE_ALIAS("platform:stm32-spdifrx");
+MODULE_LICENSE("GPL v2");
diff --git a/sound/soc/stm/stm32_spdifrx.h b/sound/soc/stm/stm32_spdifrx.h
new file mode 100644
index 0000000..0f0d43c
--- /dev/null
+++ b/sound/soc/stm/stm32_spdifrx.h
@@ -0,0 +1,224 @@
+/*
+ * STM32 ALSA SoC Digital Audio Interface (SPDIF-rx) driver.
+ *
+ * Copyright (C) 2017, STMicroelectronics - All Rights Reserved
+ * Author(s): Olivier Moysan <[email protected]> for STMicroelectronics.
+ *
+ * License terms: GPL V2.0.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
+ * details.
+ */
+
+/* SPDIF-rx Register Map */
+#define STM32_SPDIFRX_CR 0x00
+#define STM32_SPDIFRX_IMR 0x04
+#define STM32_SPDIFRX_SR 0x08
+#define STM32_SPDIFRX_IFCR 0x0C
+#define STM32_SPDIFRX_DR 0x10
+#define STM32_SPDIFRX_CSR 0x14
+#define STM32_SPDIFRX_DIR 0x18
+
+/* Bit definition for SPDIF_CR register */
+#define SPDIFRX_CR_SPDIFEN_SHIFT 0
+#define SPDIFRX_CR_SPDIFEN_MASK GENMASK(1, SPDIFRX_CR_SPDIFEN_SHIFT)
+#define SPDIFRX_CR_SPDIFENSET(x) ((x) << SPDIFRX_CR_SPDIFEN_SHIFT)
+
+#define SPDIFRX_CR_RXDMAEN BIT(2)
+#define SPDIFRX_CR_RXSTEO BIT(3)
+
+#define SPDIFRX_CR_DRFMT_SHIFT 4
+#define SPDIFRX_CR_DRFMT_MASK GENMASK(5, SPDIFRX_CR_DRFMT_SHIFT)
+#define SPDIFRX_CR_DRFMTSET(x) ((x) << SPDIFRX_CR_DRFMT_SHIFT)
+
+#define SPDIFRX_CR_PMSK BIT(6)
+#define SPDIFRX_CR_VMSK BIT(7)
+#define SPDIFRX_CR_CUMSK BIT(8)
+#define SPDIFRX_CR_PTMSK BIT(9)
+#define SPDIFRX_CR_CBDMAEN BIT(10)
+#define SPDIFRX_CR_CHSEL_SHIFT 11
+#define SPDIFRX_CR_CHSEL BIT(SPDIFRX_CR_CHSEL_SHIFT)
+
+#define SPDIFRX_CR_NBTR_SHIFT 12
+#define SPDIFRX_CR_NBTR_MASK GENMASK(13, SPDIFRX_CR_NBTR_SHIFT)
+#define SPDIFRX_CR_NBTRSET(x) ((x) << SPDIFRX_CR_NBTR_SHIFT)
+
+#define SPDIFRX_CR_WFA BIT(14)
+
+#define SPDIFRX_CR_INSEL_SHIFT 16
+#define SPDIFRX_CR_INSEL_MASK GENMASK(18, PDIFRX_CR_INSEL_SHIFT)
+#define SPDIFRX_CR_INSELSET(x) ((x) << SPDIFRX_CR_INSEL_SHIFT)
+
+#define SPDIFRX_CR_CKSEN_SHIFT 20
+#define SPDIFRX_CR_CKSEN BIT(20)
+#define SPDIFRX_CR_CKSBKPEN BIT(21)
+
+/* Bit definition for SPDIFRX_IMR register */
+#define SPDIFRX_IMR_RXNEI BIT(0)
+#define SPDIFRX_IMR_CSRNEIE BIT(1)
+#define SPDIFRX_IMR_PERRIE BIT(2)
+#define SPDIFRX_IMR_OVRIE BIT(3)
+#define SPDIFRX_IMR_SBLKIE BIT(4)
+#define SPDIFRX_IMR_SYNCDIE BIT(5)
+#define SPDIFRX_IMR_IFEIE BIT(6)
+
+#define SPDIFRX_XIMR_MASK GENMASK(6, 0)
+
+/* Bit definition for SPDIFRX_SR register */
+#define SPDIFRX_SR_RXNE BIT(0)
+#define SPDIFRX_SR_CSRNE BIT(1)
+#define SPDIFRX_SR_PERR BIT(2)
+#define SPDIFRX_SR_OVR BIT(3)
+#define SPDIFRX_SR_SBD BIT(4)
+#define SPDIFRX_SR_SYNCD BIT(5)
+#define SPDIFRX_SR_FERR BIT(6)
+#define SPDIFRX_SR_SERR BIT(7)
+#define SPDIFRX_SR_TERR BIT(8)
+
+#define SPDIFRX_SR_WIDTH5_SHIFT 16
+#define SPDIFRX_SR_WIDTH5_MASK GENMASK(30, PDIFRX_SR_WIDTH5_SHIFT)
+#define SPDIFRX_SR_WIDTH5SET(x) ((x) << SPDIFRX_SR_WIDTH5_SHIFT)
+
+/* Bit definition for SPDIFRX_IFCR register */
+#define SPDIFRX_IFCR_PERRCF BIT(2)
+#define SPDIFRX_IFCR_OVRCF BIT(3)
+#define SPDIFRX_IFCR_SBDCF BIT(4)
+#define SPDIFRX_IFCR_SYNCDCF BIT(5)
+
+#define SPDIFRX_XIFCR_MASK GENMASK(5, 2)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b00) */
+#define SPDIFRX_DR0_DR_SHIFT 0
+#define SPDIFRX_DR0_DR_MASK GENMASK(23, SPDIFRX_DR0_DR_SHIFT)
+#define SPDIFRX_DR0_DRSET(x) ((x) << SPDIFRX_DR0_DR_SHIFT)
+
+#define SPDIFRX_DR0_PE BIT(24)
+
+#define SPDIFRX_DR0_V BIT(25)
+#define SPDIFRX_DR0_U BIT(26)
+#define SPDIFRX_DR0_C BIT(27)
+
+#define SPDIFRX_DR0_PT_SHIFT 28
+#define SPDIFRX_DR0_PT_MASK GENMASK(29, SPDIFRX_DR0_PT_SHIFT)
+#define SPDIFRX_DR0_PTSET(x) ((x) << SPDIFRX_DR0_PT_SHIFT)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b01) */
+#define SPDIFRX_DR1_PE BIT(0)
+#define SPDIFRX_DR1_V BIT(1)
+#define SPDIFRX_DR1_U BIT(2)
+#define SPDIFRX_DR1_C BIT(3)
+
+#define SPDIFRX_DR1_PT_SHIFT 4
+#define SPDIFRX_DR1_PT_MASK GENMASK(5, SPDIFRX_DR1_PT_SHIFT)
+#define SPDIFRX_DR1_PTSET(x) ((x) << SPDIFRX_DR1_PT_SHIFT)
+
+#define SPDIFRX_DR1_DR_SHIFT 8
+#define SPDIFRX_DR1_DR_MASK GENMASK(31, SPDIFRX_DR1_DR_SHIFT)
+#define SPDIFRX_DR1_DRSET(x) ((x) << SPDIFRX_DR1_DR_SHIFT)
+
+/* Bit definition for SPDIFRX_DR register (DRFMT = 0b10) */
+#define SPDIFRX_DR1_DRNL1_SHIFT 0
+#define SPDIFRX_DR1_DRNL1_MASK GENMASK(15, SPDIFRX_DR1_DRNL1_SHIFT)
+#define SPDIFRX_DR1_DRNL1SET(x) ((x) << SPDIFRX_DR1_DRNL1_SHIFT)
+
+#define SPDIFRX_DR1_DRNL2_SHIFT 16
+#define SPDIFRX_DR1_DRNL2_MASK GENMASK(31, SPDIFRX_DR1_DRNL2_SHIFT)
+#define SPDIFRX_DR1_DRNL2SET(x) ((x) << SPDIFRX_DR1_DRNL2_SHIFT)
+
+/* Bit definition for SPDIFRX_CSR register */
+#define SPDIFRX_CSR_USR_SHIFT 0
+#define SPDIFRX_CSR_USR_MASK GENMASK(15, SPDIFRX_CSR_USR_SHIFT)
+#define SPDIFRX_CSR_USRGET(x) (((x) & SPDIFRX_CSR_USR_MASK)\
+ >> SPDIFRX_CSR_USR_SHIFT)
+
+#define SPDIFRX_CSR_CS_SHIFT 16
+#define SPDIFRX_CSR_CS_MASK GENMASK(23, SPDIFRX_CSR_CS_SHIFT)
+#define SPDIFRX_CSR_CSGET(x) (((x) & SPDIFRX_CSR_CS_MASK)\
+ >> SPDIFRX_CSR_CS_SHIFT)
+
+#define SPDIFRX_CSR_SOB BIT(24)
+
+/* Bit definition for SPDIFRX_DIR register */
+#define SPDIFRX_DIR_THI_SHIFT 0
+#define SPDIFRX_DIR_THI_MASK GENMASK(12, SPDIFRX_DIR_THI_SHIFT)
+#define SPDIFRX_DIR_THI_SET(x) ((x) << SPDIFRX_DIR_THI_SHIFT)
+
+#define SPDIFRX_DIR_TLO_SHIFT 16
+#define SPDIFRX_DIR_TLO_MASK GENMASK(28, SPDIFRX_DIR_TLO_SHIFT)
+#define SPDIFRX_DIR_TLO_SET(x) ((x) << SPDIFRX_DIR_TLO_SHIFT)
+
+#define SPDIFRX_SPDIFEN_DISABLE 0x0
+#define SPDIFRX_SPDIFEN_SYNC 0x1
+#define SPDIFRX_SPDIFEN_ENABLE 0x3
+
+#define SPDIFRX_IN1 0x1
+#define SPDIFRX_IN2 0x2
+#define SPDIFRX_IN3 0x3
+#define SPDIFRX_IN4 0x4
+#define SPDIFRX_IN5 0x5
+#define SPDIFRX_IN6 0x6
+#define SPDIFRX_IN7 0x7
+#define SPDIFRX_IN8 0x8
+
+#define SPDIFRX_NBTR_NONE 0x0
+#define SPDIFRX_NBTR_3 0x1
+#define SPDIFRX_NBTR_15 0x2
+#define SPDIFRX_NBTR_63 0x3
+
+#define SPDIFRX_DRFMT_RIGHT 0x0
+#define SPDIFRX_DRFMT_LEFT 0x1
+#define SPDIFRX_DRFMT_PACKED 0x2
+
+/* 192 CS bits in S/PDIF frame. i.e 24 CS bytes */
+#define SPDIFRX_CS_BYTES_NB 24
+/* CS byte is retrieved in 32b words */
+#define SPDIFRX_CS_BUF_LENGTH (SPDIFRX_CS_BYTES_NB * 4)
+#define SPDIFRX_UB_BYTES_NB (SPDIFRX_CS_BYTES_NB * 2)
+
+/**
+ * struct stm32_spdifrx_data - private data of SPDIFRX
+ * @pdev: device data pointer
+ * @base: mmio register base virtual address
+ * @regmap: SPDIFRX register map pointer
+ * @regmap_conf: SPDIFRX register map configuration pointer
+ * @cs_completion: channel status retrieving completion
+ * @kclk: kernel clock feeding the SPDIFRX clock generator
+ * @pclk: peripheral clock driving bus interface
+ * @dma_params: dma configuration data for rx channel
+ * @substream: PCM substream data pointer
+ * @dmab: dma buffer info pointer
+ * @ctrl_chan: dma channel for S/PDIF control bits
+ * @desc:dma async transaction descriptor
+ * @slave_config: dma slave channel runtime config pointer
+ * @phys_addr: SPDIFRX registers physical base address
+ * @lock: synchronization enabling lock
+ * @cs: channel status buffer
+ * @ub: user data buffer
+ * @irq: SPDIFRX interrupt line
+ */
+struct stm32_spdifrx_data {
+ struct platform_device *pdev;
+ void __iomem *base;
+ struct regmap *regmap;
+ const struct regmap_config *regmap_conf;
+ struct completion cs_completion;
+ struct clk *kclk;
+ struct clk *pclk;
+ struct snd_dmaengine_dai_dma_data dma_params;
+ struct snd_pcm_substream *substream;
+ struct snd_dma_buffer *dmab;
+ struct dma_chan *ctrl_chan;
+ struct dma_async_tx_descriptor *desc;
+ struct dma_slave_config slave_config;
+ dma_addr_t phys_addr;
+ spinlock_t lock; /* sync enabling lock */
+ unsigned char cs[SPDIFRX_CS_BYTES_NB];
+ unsigned char ub[SPDIFRX_UB_BYTES_NB];
+ int irq;
+};
--
1.9.1
On Fri, Jun 16, 2017 at 03:57:32PM +0200, olivier moysan wrote:
> Add SPDIFRX support to STM32.
This doesn't apply against current code, please check and resend. Looks
good code wise.
The patch
ASoC: stm32: Add DT bindings for SPDIFRX interface
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 0507cb0226acfd7ba114c59f6a76fdc7a1c6b01e Mon Sep 17 00:00:00 2001
From: olivier moysan <[email protected]>
Date: Tue, 20 Jun 2017 11:58:46 +0200
Subject: [PATCH] ASoC: stm32: Add DT bindings for SPDIFRX interface
Add documentation of device tree bindings for the
STM32 SPDIFRX interface.
Signed-off-by: olivier moysan <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
---
.../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56 ++++++++++++++++++++++
1 file changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
new file mode 100644
index 000000000000..33826f2459fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
@@ -0,0 +1,56 @@
+STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
+
+The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
+IEC-60958 and IEC-61937.
+
+Required properties:
+ - compatible: should be "st,stm32h7-spdifrx"
+ - reg: cpu DAI IP base address and size
+ - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
+ - clock-names: must contain "kclk"
+ - interrupts: cpu DAI interrupt line
+ - dmas: DMA specifiers for audio data DMA and iec control flow DMA
+ See STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt
+ - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
+
+Optional properties:
+ - resets: Reference to a reset controller asserting the SPDIFRX
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+graph.txt.
+
+Example:
+spdifrx: spdifrx@40004000 {
+ compatible = "st,stm32h7-spdifrx";
+ reg = <0x40004000 0x400>;
+ clocks = <&rcc SPDIFRX_CK>;
+ clock-names = "kclk";
+ interrupts = <97>;
+ dmas = <&dmamux1 2 93 0x400 0x0>,
+ <&dmamux1 3 94 0x400 0x0>;
+ dma-names = "rx", "rx-ctrl";
+ pinctrl-0 = <&spdifrx_pins>;
+ pinctrl-names = "default";
+
+ spdifrx_port: port {
+ cpu_endpoint: endpoint {
+ remote-endpoint = <&codec_endpoint>;
+ };
+ };
+};
+
+spdif_in: spdif-in {
+ compatible = "linux,spdif-dir";
+
+ codec_port: port {
+ codec_endpoint: endpoint {
+ remote-endpoint = <&cpu_endpoint>;
+ };
+ };
+};
+
+soundcard {
+ compatible = "audio-graph-card";
+ dais = <&spdifrx_port>;
+};
--
2.11.0
On Fri, Jun 16, 2017 at 03:57:31PM +0200, olivier moysan wrote:
> This adds documentation of device tree bindings for the
> STM32 SPDIFRX interface.
>
> Signed-off-by: olivier moysan <[email protected]>
> ---
> .../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56 ++++++++++++++++++++++
> 1 file changed, 56 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>
> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
> new file mode 100644
> index 0000000..33826f2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
> @@ -0,0 +1,56 @@
> +STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
> +
> +The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
> +IEC-60958 and IEC-61937.
> +
> +Required properties:
> + - compatible: should be "st,stm32h7-spdifrx"
> + - reg: cpu DAI IP base address and size
> + - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
> + - clock-names: must contain "kclk"
> + - interrupts: cpu DAI interrupt line
> + - dmas: DMA specifiers for audio data DMA and iec control flow DMA
> + See STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt
> + - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
> +
> +Optional properties:
> + - resets: Reference to a reset controller asserting the SPDIFRX
> +
> +The device node should contain one 'port' child node with one child 'endpoint'
> +node, according to the bindings defined in Documentation/devicetree/bindings/
> +graph.txt.
> +
> +Example:
> +spdifrx: spdifrx@40004000 {
> + compatible = "st,stm32h7-spdifrx";
> + reg = <0x40004000 0x400>;
> + clocks = <&rcc SPDIFRX_CK>;
> + clock-names = "kclk";
> + interrupts = <97>;
> + dmas = <&dmamux1 2 93 0x400 0x0>,
> + <&dmamux1 3 94 0x400 0x0>;
> + dma-names = "rx", "rx-ctrl";
> + pinctrl-0 = <&spdifrx_pins>;
> + pinctrl-names = "default";
> +
> + spdifrx_port: port {
> + cpu_endpoint: endpoint {
> + remote-endpoint = <&codec_endpoint>;
> + };
> + };
> +};
> +
> +spdif_in: spdif-in {
> + compatible = "linux,spdif-dir";
What is this? It should go.
Rob
Hello Rob,
On 06/23/2017 08:55 PM, Rob Herring wrote:
> On Fri, Jun 16, 2017 at 03:57:31PM +0200, olivier moysan wrote:
>> This adds documentation of device tree bindings for the
>> STM32 SPDIFRX interface.
>>
>> Signed-off-by: olivier moysan <[email protected]>
>> ---
>> .../devicetree/bindings/sound/st,stm32-spdifrx.txt | 56 ++++++++++++++++++++++
>> 1 file changed, 56 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>>
>> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>> new file mode 100644
>> index 0000000..33826f2
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
>> @@ -0,0 +1,56 @@
>> +STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
>> +
>> +The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
>> +IEC-60958 and IEC-61937.
>> +
>> +Required properties:
>> + - compatible: should be "st,stm32h7-spdifrx"
>> + - reg: cpu DAI IP base address and size
>> + - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
>> + - clock-names: must contain "kclk"
>> + - interrupts: cpu DAI interrupt line
>> + - dmas: DMA specifiers for audio data DMA and iec control flow DMA
>> + See STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt
>> + - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
>> +
>> +Optional properties:
>> + - resets: Reference to a reset controller asserting the SPDIFRX
>> +
>> +The device node should contain one 'port' child node with one child 'endpoint'
>> +node, according to the bindings defined in Documentation/devicetree/bindings/
>> +graph.txt.
>> +
>> +Example:
>> +spdifrx: spdifrx@40004000 {
>> + compatible = "st,stm32h7-spdifrx";
>> + reg = <0x40004000 0x400>;
>> + clocks = <&rcc SPDIFRX_CK>;
>> + clock-names = "kclk";
>> + interrupts = <97>;
>> + dmas = <&dmamux1 2 93 0x400 0x0>,
>> + <&dmamux1 3 94 0x400 0x0>;
>> + dma-names = "rx", "rx-ctrl";
>> + pinctrl-0 = <&spdifrx_pins>;
>> + pinctrl-names = "default";
>> +
>> + spdifrx_port: port {
>> + cpu_endpoint: endpoint {
>> + remote-endpoint = <&codec_endpoint>;
>> + };
>> + };
>> +};
>> +
>> +spdif_in: spdif-in {
>> + compatible = "linux,spdif-dir";
>
> What is this? It should go.
>
> Rob
>
This is the ASoC spdif stub codec. This is relevant in DT when
spdif interface is wired to a connector.
I will remove it from bindings.
BRs
olivier