2021-05-19 19:26:42

by liuqi (BA)

[permalink] [raw]
Subject: [PATCH v4 1/2] docs: perf: Add description for HiSilicon PCIe PMU driver

PCIe PMU Root Complex Integrated End Point(RCiEP) device is supported on
HiSilicon HIP09 platform. Document it to provide guidance on how to
use it.

Signed-off-by: Qi Liu <[email protected]>
---
Documentation/admin-guide/perf/hisi-pcie-pmu.rst | 104 +++++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 Documentation/admin-guide/perf/hisi-pcie-pmu.rst

diff --git a/Documentation/admin-guide/perf/hisi-pcie-pmu.rst b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst
new file mode 100644
index 0000000..2084b53
--- /dev/null
+++ b/Documentation/admin-guide/perf/hisi-pcie-pmu.rst
@@ -0,0 +1,104 @@
+================================================
+HiSilicon PCIe Performance Monitoring Unit (PMU)
+================================================
+
+HiSilicon PCIe Performance Monitoring Unit (PMU) is a PCIe Root Complex
+integrated End Point (RCiEP) device. On Hip09, each PCIe Core has a PMU RCiEP
+to monitor multi Root Ports and all Endpoints downstream these Root Ports.
+
+HiSilicon PCIe PMU is supported to collect performance data of PCIe bus, such
+as: bandwidth, latency etc.
+
+
+HiSilicon PCIe PMU driver
+=========================
+
+The PCIe PMU driver registers a perf PMU with the name of its sicl-id and PCIe
+Core id.::
+
+ /sys/bus/event_source/hisi_pcie<sicl>_<core>
+
+PMU driver provides description of available events and filter options in sysfs,
+see /sys/bus/event_source/devices/hisi_pcie<sicl>_<core>.
+
+The "format" directory describes all formats of the config (events) and config1
+(filter options) fields of the perf_event_attr structure. The "events" directory
+describes all documented events shown in perf list.
+
+The "identifier" sysfs file allows users to identify the version of the
+PMU hardware device.
+
+The "bus" sysfs file allows users to get the bus number of Root Ports
+monitored by PMU.
+
+Example usage of perf::
+
+ $# perf list
+ hisi_pcie0_0/bw_rx/ [kernel PMU event]
+ ------------------------------------------
+
+ $# perf stat -e hisi_pcie0_0/bw_rx/ sleep 5
+
+The current driver does not support sampling. So "perf record" is unsupported.
+Also attach to a task is unsupported for PCIe PMU.
+
+Filter options
+--------------
+
+1. Target filter
+PMU could only monitor the performance of traffic downstream target Root Ports
+or downstream target Endpoint. PCIe PMU driver support "port" and "bdf"
+interfaces for users, and these two interfaces aren't supported at the same
+time.
+
+-port
+"port" filter can be used in all PCIe PMU events, target Root Port can be
+selected by configuring the 16-bits-bitmap "port". Multi ports can be selected
+for AP-layer-events, and only one port can be selected for TL/DL-layer-events.
+
+For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap
+should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes),
+bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101.
+
+Example usage of perf::
+
+ $# perf stat -e hisi_pcie0_0/bw_rx,port=0x1/ sleep 5
+
+-bdf
+
+"bdf" filter can only be used in bandwidth events, target Endpoint is selected
+by configuring BDF to "bdf". Counter only counts the bandwidth of message
+requested by target Endpoint.
+
+For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0.
+
+Example usage of perf::
+
+ $# perf stat -e hisi_pcie0_0/bw_rx,bdf=0x3900/ sleep 5
+
+2. Trigger filter
+Event statistics start when the first time TLP length is greater/smaller
+than trigger condition. You can set the trigger condition by writing "trig_len",
+and set the trigger mode by writing "trig_mode". This filter can only be used
+in bandwidth events.
+
+For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0"
+means statistics start when TLP length > trigger condition, "trig_mode=1"
+means start when TLP length < condition.
+
+Example usage of perf::
+
+ $# perf stat -e hisi_pcie0_0/bw_rx,trig_len=0x4,trig_mode=1/ sleep 5
+
+3. Threshold filter
+Counter counts when TLP length within the specified range. You can set the
+threshold by writing "thr_len", and set the threshold mode by writing
+"thr_mode". This filter can only be used in bandwidth events.
+
+For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means
+counter counts when TLP length >= threshold, and "thr_mode=1" means counts
+when TLP length < threshold.
+
+Example usage of perf::
+
+ $# perf stat -e hisi_pcie0_0/bw_rx,thr_len=0x4,thr_mode=1/ sleep 5
--
2.7.4



2021-05-19 19:30:41

by John Garry

[permalink] [raw]
Subject: Re: [PATCH v4 1/2] docs: perf: Add description for HiSilicon PCIe PMU driver

On 19/05/2021 10:49, Qi Liu wrote:
> PCIe PMU Root Complex Integrated End Point(RCiEP) device is supported on
> HiSilicon HIP09 platform. Document it to provide guidance on how to
> use it.
>
> Signed-off-by: Qi Liu<[email protected]>

Reviewed-by: John Garry <[email protected]>

JFYI, perf tool iostat support is in 5.13-rc1, so we can look to add
support for this HW as well in future.

My impression is that we should use metricgroups.

Thanks,
John

2021-05-20 03:23:45

by liuqi (BA)

[permalink] [raw]
Subject: Re: [PATCH v4 1/2] docs: perf: Add description for HiSilicon PCIe PMU driver


Hi John,
On 2021/5/19 19:44, John Garry wrote:
> On 19/05/2021 10:49, Qi Liu wrote:
>> PCIe PMU Root Complex Integrated End Point(RCiEP) device is supported on
>> HiSilicon HIP09 platform. Document it to provide guidance on how to
>> use it.
>>
>> Signed-off-by: Qi Liu<[email protected]>
>
> Reviewed-by: John Garry <[email protected]>
>
> JFYI, perf tool iostat support is in 5.13-rc1, so we can look to add
> support for this HW as well in future.
>
> My impression is that we should use metricgroups.
>

Yes, perf iostat makes it easier for users to monitor PCIe bandwidth.
I'll add perf iostat for HiSilicon PCIe PMU latter.

Thanks, Qi
> Thanks,
> John
>
> .