Changes in V8:
- As per Matthias comments
Added qup_spiN_cs_gpio nodes in all spi ports
- As per Doug comments, Added "qcom,sc7280-qspi" compatible in qspi node
Changes in V7:
- As per Stephen's comments
1. Moved qup_opp_table under /soc@0/geniqup@9c0000
2. Removed qupv3_id_1 in sc7280-idp board file
3. Sorted alias names for i2c and spi as per alphabet order
- As per Matthias comment
Configuring cs pin with gpio (qup_spiN_cs_gpio) definitions are removed
Changes in V6:
- As per Matthias' comments,
1. Squashed "Update QUPv3 UART5 DT node" and "Configure debug
uart for sc7280-idp"
2. Moved qup_opp_table from /soc to /
3. Changed convention "clocks" followed by "clock-names"
- As per Doug comments, added aliases for i2c and spi
Changes in V5:
- As per Matthias' comments, I've split the patches as below:
1. Add QSPI node
2. Configure SPI-NOR FLASH for sc7280-idp
3. Add QUPv3 wrapper_0 nodes
4. Update QUPv3 UART5 DT node
5. Configure debug uart for sc7280-idp
6. Configure uart7 to support bluetooth on sc7280-idp
7. Add QUPv3 wrapper_1 nodes
Changes in V4:
- As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
qspi_opp_table from /soc to / (root).
- As per Bjorn's comment, added QUP Wrapper_0 nodes
as separate patch and debug-uart node as separate patch.
- Dropped interconnect votes for wrapper_0 and wrapper_1 node
- Corrected QUP Wrapper_1 SE node's pin control functions like below
QUP Wrapper_0: SE0-SE7 uses qup00 - qup07 pin-cntrl functions.
QUP Wrapper_1: SE0-SE7 uses qup10 - qup17 pin-cntrl functions.
Changes in V3:
- Broken the huge V2 patch into 3 smaller patches.
1. QSPI DT nodes
2. QUP wrapper_0 DT nodes
3. QUP wrapper_1 DT nodes
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
Rajesh Patil (4):
dt-bindings: spi: add QSPI bindings for sc7280 chipset
arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp
arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp
arm64: dts: sc7280: Add aliases for I2C and SPI
Roja Rani Yarubandi (4):
arm64: dts: sc7280: Add QSPI node
arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
arm64: dts: sc7280: Update QUPv3 UART5 DT node
arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes
.../bindings/spi/qcom,spi-qcom-qspi.yaml | 5 +-
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 125 +-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 3216 +++++++++++++++-----
3 files changed, 2520 insertions(+), 826 deletions(-)
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
From: Roja Rani Yarubandi <[email protected]>
Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.
Signed-off-by: Roja Rani Yarubandi <[email protected]>
Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
---
Changes in V8:
- No changes
Changes in V7:
- As per Stephen's comments, Removed "status=okay" in qupv3_id_1 for sc7280-idp board file
Changes in V5:
- As per Matthias' comments, Add QUPv3 wrapper_1 nodes
arch/arm64/boot/dts/qcom/sc7280.dtsi | 749 +++++++++++++++++++++++++++++++++++
1 file changed, 749 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 4410b5b..d98da8e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -981,6 +981,435 @@
};
};
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x2000>;
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ clock-names = "m-ahb", "s-ahb";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x43 0x0>;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_data_clk>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a84000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a98000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart14: serial@a98000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a98000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart15: serial@a9c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
cnoc2: interconnect@1500000 {
reg = <0 0x01500000 0 0x1000>;
compatible = "qcom,sc7280-cnoc2";
@@ -2039,6 +2468,46 @@
function = "qup07";
};
+ qup_i2c8_data_clk: qup-i2c8-data-clk {
+ pins = "gpio32", "gpio33";
+ function = "qup10";
+ };
+
+ qup_i2c9_data_clk: qup-i2c9-data-clk {
+ pins = "gpio36", "gpio37";
+ function = "qup11";
+ };
+
+ qup_i2c10_data_clk: qup-i2c10-data-clk {
+ pins = "gpio40", "gpio41";
+ function = "qup12";
+ };
+
+ qup_i2c11_data_clk: qup-i2c11-data-clk {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ };
+
+ qup_i2c12_data_clk: qup-i2c12-data-clk {
+ pins = "gpio48", "gpio49";
+ function = "qup14";
+ };
+
+ qup_i2c13_data_clk: qup-i2c13-data-clk {
+ pins = "gpio52", "gpio53";
+ function = "qup15";
+ };
+
+ qup_i2c14_data_clk: qup-i2c14-data-clk {
+ pins = "gpio56", "gpio57";
+ function = "qup16";
+ };
+
+ qup_i2c15_data_clk: qup-i2c15-data-clk {
+ pins = "gpio60", "gpio61";
+ function = "qup17";
+ };
+
qup_spi0_data_clk: qup-spi0-data-clk {
pins = "gpio0", "gpio1", "gpio2";
function = "qup00";
@@ -2159,6 +2628,126 @@
function = "gpio";
};
+ qup_spi8_data_clk: qup-spi8-data-clk {
+ pins = "gpio32", "gpio33", "gpio34";
+ function = "qup10";
+ };
+
+ qup_spi8_cs: qup-spi8-cs {
+ pins = "gpio35";
+ function = "qup10";
+ };
+
+ qup_spi8_cs_gpio: qup-spi8-cs_gpio {
+ pins = "gpio35";
+ function = "gpio";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk {
+ pins = "gpio36", "gpio37", "gpio38";
+ function = "qup11";
+ };
+
+ qup_spi9_cs: qup-spi9-cs {
+ pins = "gpio39";
+ function = "qup11";
+ };
+
+ qup_spi9_cs_gpio: qup-spi9-cs_gpio {
+ pins = "gpio39";
+ function = "gpio";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk {
+ pins = "gpio40", "gpio41", "gpio42";
+ function = "qup12";
+ };
+
+ qup_spi10_cs: qup-spi10-cs {
+ pins = "gpio43";
+ function = "qup12";
+ };
+
+ qup_spi10_cs_gpio: qup-spi10-cs_gpio {
+ pins = "gpio43";
+ function = "gpio";
+ };
+
+ qup_spi11_data_clk: qup-spi11-data-clk {
+ pins = "gpio44", "gpio45", "gpio46";
+ function = "qup13";
+ };
+
+ qup_spi11_cs: qup-spi11-cs {
+ pins = "gpio47";
+ function = "qup13";
+ };
+
+ qup_spi11_cs_gpio: qup-spi11-cs_gpio {
+ pins = "gpio47";
+ function = "gpio";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk {
+ pins = "gpio48", "gpio49", "gpio50";
+ function = "qup14";
+ };
+
+ qup_spi12_cs: qup-spi12-cs {
+ pins = "gpio51";
+ function = "qup14";
+ };
+
+ qup_spi12_cs_gpio: qup-spi12-cs_gpio {
+ pins = "gpio51";
+ function = "gpio";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk {
+ pins = "gpio52", "gpio53", "gpio54";
+ function = "qup15";
+ };
+
+ qup_spi13_cs: qup-spi13-cs {
+ pins = "gpio55";
+ function = "qup15";
+ };
+
+ qup_spi13_cs_gpio: qup-spi13-cs_gpio {
+ pins = "gpio55";
+ function = "gpio";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk {
+ pins = "gpio56", "gpio57", "gpio58";
+ function = "qup16";
+ };
+
+ qup_spi14_cs: qup-spi14-cs {
+ pins = "gpio59";
+ function = "qup16";
+ };
+
+ qup_spi14_cs_gpio: qup-spi14-cs_gpio {
+ pins = "gpio59";
+ function = "gpio";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk {
+ pins = "gpio60", "gpio61", "gpio62";
+ function = "qup17";
+ };
+
+ qup_spi15_cs: qup-spi15-cs {
+ pins = "gpio63";
+ function = "qup17";
+ };
+
+ qup_spi15_cs_gpio: qup-spi15-cs_gpio {
+ pins = "gpio63";
+ function = "gpio";
+ };
+
qup_uart0_cts: qup-uart0-cts {
pins = "gpio0";
function = "qup00";
@@ -2399,6 +2988,166 @@
bias-bus-hold;
};
};
+
+ qup_uart8_cts: qup-uart8-cts {
+ pins = "gpio32";
+ function = "qup10";
+ };
+
+ qup_uart8_rts: qup-uart8-rts {
+ pins = "gpio33";
+ function = "qup10";
+ };
+
+ qup_uart8_tx: qup-uart8-tx {
+ pins = "gpio34";
+ function = "qup10";
+ };
+
+ qup_uart8_rx: qup-uart8-rx {
+ pins = "gpio35";
+ function = "qup10";
+ };
+
+ qup_uart9_cts: qup-uart9-cts {
+ pins = "gpio36";
+ function = "qup11";
+ };
+
+ qup_uart9_rts: qup-uart9-rts {
+ pins = "gpio37";
+ function = "qup11";
+ };
+
+ qup_uart9_tx: qup-uart9-tx {
+ pins = "gpio38";
+ function = "qup11";
+ };
+
+ qup_uart9_rx: qup-uart9-rx {
+ pins = "gpio39";
+ function = "qup11";
+ };
+
+ qup_uart10_cts: qup-uart10-cts {
+ pins = "gpio40";
+ function = "qup12";
+ };
+
+ qup_uart10_rts: qup-uart10-rts {
+ pins = "gpio41";
+ function = "qup12";
+ };
+
+ qup_uart10_tx: qup-uart10-tx {
+ pins = "gpio42";
+ function = "qup12";
+ };
+
+ qup_uart10_rx: qup-uart10-rx {
+ pins = "gpio43";
+ function = "qup12";
+ };
+
+ qup_uart11_cts: qup-uart11-cts {
+ pins = "gpio44";
+ function = "qup13";
+ };
+
+ qup_uart11_rts: qup-uart11-rts {
+ pins = "gpio45";
+ function = "qup13";
+ };
+
+ qup_uart11_tx: qup-uart11-tx {
+ pins = "gpio46";
+ function = "qup13";
+ };
+
+ qup_uart11_rx: qup-uart11-rx {
+ pins = "gpio47";
+ function = "qup13";
+ };
+
+ qup_uart12_cts: qup-uart12-cts {
+ pins = "gpio48";
+ function = "qup14";
+ };
+
+ qup_uart12_rts: qup-uart12-rts {
+ pins = "gpio49";
+ function = "qup14";
+ };
+
+ qup_uart12_tx: qup-uart12-tx {
+ pins = "gpio50";
+ function = "qup14";
+ };
+
+ qup_uart12_rx: qup-uart12-rx {
+ pins = "gpio51";
+ function = "qup14";
+ };
+
+ qup_uart13_cts: qup-uart13-cts {
+ pins = "gpio52";
+ function = "qup15";
+ };
+
+ qup_uart13_rts: qup-uart13-rts {
+ pins = "gpio53";
+ function = "qup15";
+ };
+
+ qup_uart13_tx: qup-uart13-tx {
+ pins = "gpio54";
+ function = "qup15";
+ };
+
+ qup_uart13_rx: qup-uart13-rx {
+ pins = "gpio55";
+ function = "qup15";
+ };
+
+ qup_uart14_cts: qup-uart14-cts {
+ pins = "gpio56";
+ function = "qup16";
+ };
+
+ qup_uart14_rts: qup-uart14-rts {
+ pins = "gpio57";
+ function = "qup16";
+ };
+
+ qup_uart14_tx: qup-uart14-tx {
+ pins = "gpio58";
+ function = "qup16";
+ };
+
+ qup_uart14_rx: qup-uart14-rx {
+ pins = "gpio59";
+ function = "qup16";
+ };
+
+ qup_uart15_cts: qup-uart15-cts {
+ pins = "gpio60";
+ function = "qup17";
+ };
+
+ qup_uart15_rts: qup-uart15-rts {
+ pins = "gpio61";
+ function = "qup17";
+ };
+
+ qup_uart15_tx: qup-uart15-tx {
+ pins = "gpio62";
+ function = "qup17";
+ };
+
+ qup_uart15_rx: qup-uart15-rx {
+ pins = "gpio63";
+ function = "qup17";
+ };
};
apps_smmu: iommu@15000000 {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Add spi-nor flash node and pinctrl configurations for the SC7280 IDP.
Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
---
Changes in V8:
- No changes
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 99f9ee5..37b8444 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -211,6 +211,20 @@
vcc-supply = <&vreg_l1c_1p8>;
};
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <37500000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -288,6 +302,19 @@
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+&qspi_cs0 {
+ bias-disable;
+};
+
+&qspi_clk {
+ bias-disable;
+};
+
+&qspi_data01 {
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+};
+
&qup_uart5_default {
tx {
pins = "gpio46";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
From: Roja Rani Yarubandi <[email protected]>
Add QSPI DT node and qspi_opp_table for SC7280 SoC.
Move qspi_opp_table to / because SPI nodes assume
any child node is a spi device and so we can't put the
table underneath the spi controller.
Signed-off-by: Roja Rani Yarubandi <[email protected]>
Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
---
Changes in V8:
- As per Doug's comments, Added "qcom,sc7280-qspi" compatible in qspi node
Changes in V6:
- As per Stephen comments, updated commit message regarding qspi_opp_table
moved from /soc to /
Changes in V4:
- As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
qspi_opp_table from /soc to / (root).
Changes in V3:
- Broken the huge V2 patch into 3 smaller patches.
1. QSPI DT nodes
2. QUP wrapper_0 DT nodes
3. QUP wrapper_1 DT nodes
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
arch/arm64/boot/dts/qcom/sc7280.dtsi | 61 ++++++++++++++++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index fd78f16..2fbcb0a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
method = "smc";
};
+ qspi_opp_table: qspi-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-150000000 {
+ opp-hz = /bits/ 64 <150000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
@@ -1318,6 +1337,23 @@
};
};
+ qspi: spi@88dc000 {
+ compatible = "qcom,sc7280-qspi", "qcom,qspi-v1";
+ reg = <0 0x088dc000 0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+ clock-names = "iface", "core";
+ interconnects = <&gem_noc MASTER_APPSS_PROC 0
+ &cnoc2 SLAVE_QSPI_0 0>;
+ interconnect-names = "qspi-config";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qspi_opp_table>;
+ status = "disabled";
+ };
+
dc_noc: interconnect@90e0000 {
reg = <0 0x090e0000 0 0x5080>;
compatible = "qcom,sc7280-dc-noc";
@@ -1513,6 +1549,31 @@
gpio-ranges = <&tlmm 0 0 175>;
wakeup-parent = <&pdc>;
+ qspi_clk: qspi-clk {
+ pins = "gpio14";
+ function = "qspi_clk";
+ };
+
+ qspi_cs0: qspi-cs0 {
+ pins = "gpio15";
+ function = "qspi_cs";
+ };
+
+ qspi_cs1: qspi-cs1 {
+ pins = "gpio19";
+ function = "qspi_cs";
+ };
+
+ qspi_data01: qspi-data01 {
+ pins = "gpio12", "gpio13";
+ function = "qspi_data";
+ };
+
+ qspi_data12: qspi-data12 {
+ pins = "gpio16", "gpio17";
+ function = "qspi_data";
+ };
+
qup_uart5_default: qup-uart5-default {
pins = "gpio46", "gpio47";
function = "qup13";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Add bluetooth uart pin configuration for sc7280-idp.
Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
---
Changes in V8:
- No changes
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 85 ++++++++++++++++++++++++++++++++
1 file changed, 85 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index cf82301..52638e2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -301,6 +301,16 @@
vdda18-supply = <&vreg_l1c_1p8>;
};
+&uart7 {
+ status = "okay";
+
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
&qspi_cs0 {
@@ -326,6 +336,81 @@
bias-pull-up;
};
+&qup_uart7_cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&tlmm {
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+};
+
&sdc1_on {
clk {
bias-disable;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Add aliases for i2c and spi for sc7280 soc.
Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
---
Changes in V8:
- No changes
Changes in V7:
- As per Stephen's comments, Sorted alias names for i2c and spi as per alphabet order
Changes in V6:
- As per Doug's comments, added aliases for i2c and spi
arch/arm64/boot/dts/qcom/sc7280.dtsi | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index d98da8e..0e1c532 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -26,8 +26,40 @@
chosen { };
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ i2c7 = &i2c7;
+ i2c8 = &i2c8;
+ i2c9 = &i2c9;
+ i2c10 = &i2c10;
+ i2c11 = &i2c11;
+ i2c12 = &i2c12;
+ i2c13 = &i2c13;
+ i2c14 = &i2c14;
+ i2c15 = &i2c15;
mmc1 = &sdhc_1;
mmc2 = &sdhc_2;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ spi2 = &spi2;
+ spi3 = &spi3;
+ spi4 = &spi4;
+ spi5 = &spi5;
+ spi6 = &spi6;
+ spi7 = &spi7;
+ spi8 = &spi8;
+ spi9 = &spi9;
+ spi10 = &spi10;
+ spi11 = &spi11;
+ spi12 = &spi12;
+ spi13 = &spi13;
+ spi14 = &spi14;
+ spi15 = &spi15;
};
clocks {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Quoting Rajesh Patil (2021-09-17 02:48:01)
> From: Roja Rani Yarubandi <[email protected]>
>
> Add QSPI DT node and qspi_opp_table for SC7280 SoC.
>
> Move qspi_opp_table to / because SPI nodes assume
> any child node is a spi device and so we can't put the
> table underneath the spi controller.
>
> Signed-off-by: Roja Rani Yarubandi <[email protected]>
> Signed-off-by: Rajesh Patil <[email protected]>
> Reviewed-by: Matthias Kaehlcke <[email protected]>
> ---
Reviewed-by: Stephen Boyd <[email protected]>
Quoting Rajesh Patil (2021-09-17 02:48:05)
> Add bluetooth uart pin configuration for sc7280-idp.
>
> Signed-off-by: Rajesh Patil <[email protected]>
> Reviewed-by: Matthias Kaehlcke <[email protected]>
> ---
Reviewed-by: Stephen Boyd <[email protected]>
Quoting Rajesh Patil (2021-09-17 02:48:06)
> From: Roja Rani Yarubandi <[email protected]>
>
> Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.
>
> Signed-off-by: Roja Rani Yarubandi <[email protected]>
> Signed-off-by: Rajesh Patil <[email protected]>
> Reviewed-by: Matthias Kaehlcke <[email protected]>
> ---
With the same cs_gpio node names fixed
Reviewed-by: Stephen Boyd <[email protected]>