2016-11-23 15:04:17

by Niklas Cassel

Subject: [PATCH 1/4] bindings: net: stmmac: correct note about TSO

From: Niklas Cassel <[email protected]>

snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.

TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.

Also added a note about snps,tso only being available on GMAC4 and newer.

Signed-off-by: Niklas Cassel <[email protected]>
---
Documentation/devicetree/bindings/net/stmmac.txt | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index 41b49e6075f5..b95ff998ba73 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -1,7 +1,7 @@
* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)

Required properties:
-- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
+- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
- reg: Address and length of the register set for the device
- interrupt-parent: Should be the phandle for the interrupt controller
@@ -50,6 +50,8 @@ Optional properties:
- snps,ps-speed: port selection speed that can be passed to the core when
PCS is supported. For example, this is used in case of SGMII
and MAC2MAC connection.
+- snps,tso: this enables the TSO feature otherwise it will be managed by
+ MAC HW capability register. Only for GMAC4 and newer.
- AXI BUS Mode parameters: below the list of all the parameters to program the
AXI register inside the DMA module:
- snps,lpi_en: enable Low Power Interface
@@ -62,8 +64,6 @@ Optional properties:
- snps,fb: fixed-burst
- snps,mb: mixed-burst
- snps,rb: rebuild INCRx Burst
- - snps,tso: this enables the TSO feature otherwise it will be managed by
- MAC HW capability register.
- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.

Examples:
--
2.1.4

2016-11-24 17:42:51

by Alexandre Torgue

Subject: Re: [PATCH 1/4] bindings: net: stmmac: correct note about TSO

Hi Niklas,

On 11/23/2016 03:24 PM, Niklas Cassel wrote:
> From: Niklas Cassel <[email protected]>
>
> snps,tso was previously placed under AXI BUS Mode parameters,
> suggesting that the property should be in the stmmac-axi-config node.
>
> TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
> parameters, and the parser actually expects it to be in the root node,
> not in the stmmac-axi-config.
>
> Also added a note about snps,tso only being available on GMAC4 and newer.
>
> Signed-off-by: Niklas Cassel <[email protected]>
> ---
> Documentation/devicetree/bindings/net/stmmac.txt | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
> index 41b49e6075f5..b95ff998ba73 100644
> --- a/Documentation/devicetree/bindings/net/stmmac.txt
> +++ b/Documentation/devicetree/bindings/net/stmmac.txt
> @@ -1,7 +1,7 @@
> * STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
>
> Required properties:
> -- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
> +- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
> For backwards compatibility: "st,spear600-gmac" is also supported.
> - reg: Address and length of the register set for the device
> - interrupt-parent: Should be the phandle for the interrupt controller
> @@ -50,6 +50,8 @@ Optional properties:
> - snps,ps-speed: port selection speed that can be passed to the core when
> PCS is supported. For example, this is used in case of SGMII
> and MAC2MAC connection.
> +- snps,tso: this enables the TSO feature otherwise it will be managed by
> + MAC HW capability register. Only for GMAC4 and newer.
> - AXI BUS Mode parameters: below the list of all the parameters to program the
> AXI register inside the DMA module:
> - snps,lpi_en: enable Low Power Interface
> @@ -62,8 +64,6 @@ Optional properties:
> - snps,fb: fixed-burst
> - snps,mb: mixed-burst
> - snps,rb: rebuild INCRx Burst
> - - snps,tso: this enables the TSO feature otherwise it will be managed by
> - MAC HW capability register.
> - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
>
> Examples:
>
Acked-by: <[email protected]>

2016-11-30 20:41:14

by Rob Herring

Subject: Re: [PATCH 1/4] bindings: net: stmmac: correct note about TSO

On Wed, Nov 23, 2016 at 03:24:25PM +0100, Niklas Cassel wrote:
> From: Niklas Cassel <[email protected]>
>
> snps,tso was previously placed under AXI BUS Mode parameters,
> suggesting that the property should be in the stmmac-axi-config node.
>
> TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
> parameters, and the parser actually expects it to be in the root node,
> not in the stmmac-axi-config.
>
> Also added a note about snps,tso only being available on GMAC4 and newer.
>
> Signed-off-by: Niklas Cassel <[email protected]>
> ---
> Documentation/devicetree/bindings/net/stmmac.txt | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)

Acked-by: Rob Herring <[email protected]>

2016-12-02 08:48:41

by Peppe CAVALLARO

Subject: Re: [PATCH 1/4] bindings: net: stmmac: correct note about TSO

On 11/23/2016 3:24 PM, Niklas Cassel wrote:
> From: Niklas Cassel <[email protected]>
>
> snps,tso was previously placed under AXI BUS Mode parameters,
> suggesting that the property should be in the stmmac-axi-config node.
>
> TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
> parameters, and the parser actually expects it to be in the root node,
> not in the stmmac-axi-config.
>
> Also added a note about snps,tso only being available on GMAC4 and newer.
>
> Signed-off-by: Niklas Cassel <[email protected]>

Acked-by: Giuseppe Cavallaro <[email protected]>


> ---
> Documentation/devicetree/bindings/net/stmmac.txt | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
> index 41b49e6075f5..b95ff998ba73 100644
> --- a/Documentation/devicetree/bindings/net/stmmac.txt
> +++ b/Documentation/devicetree/bindings/net/stmmac.txt
> @@ -1,7 +1,7 @@
> * STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
>
> Required properties:
> -- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
> +- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
> For backwards compatibility: "st,spear600-gmac" is also supported.
> - reg: Address and length of the register set for the device
> - interrupt-parent: Should be the phandle for the interrupt controller
> @@ -50,6 +50,8 @@ Optional properties:
> - snps,ps-speed: port selection speed that can be passed to the core when
> PCS is supported. For example, this is used in case of SGMII
> and MAC2MAC connection.
> +- snps,tso: this enables the TSO feature otherwise it will be managed by
> + MAC HW capability register. Only for GMAC4 and newer.
> - AXI BUS Mode parameters: below the list of all the parameters to program the
> AXI register inside the DMA module:
> - snps,lpi_en: enable Low Power Interface
> @@ -62,8 +64,6 @@ Optional properties:
> - snps,fb: fixed-burst
> - snps,mb: mixed-burst
> - snps,rb: rebuild INCRx Burst
> - - snps,tso: this enables the TSO feature otherwise it will be managed by
> - MAC HW capability register.
> - mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
>
> Examples:
>