During boot, I get the message:
PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
using pci=biosirq.
If I boot with pci=biosirq, as the error message suggests, I get the
same error, save the part about trying with pci=biosirq. This is with
version 2.4.0-test11-pre7 and as far back at least as test10-final. I
don't remember seeing this error on earlier versions, though I may have
glossed over it. Another possibly relevant part of the boot messages
is:
PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1039/0008] at 00:01.0
PCI: Cannot allocate resource region 9 of bridge 00:02.0
My motherboard uses the SiS530 chipset, and the bridge at 00:02.0 is the
AGP bridge. If anyone's interested, I have the entire boot log.
Hello!
> During boot, I get the message:
>
> PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> using pci=biosirq.
Can you send me 'lspci -vvx' output, please?
Have a nice fortnight
--
Martin `MJ' Mares <[email protected]> <[email protected]> http://atrey.karlin.mff.cuni.cz/~mj/
"System going down at 1:45 for disk crashing."
Martin Mares <[email protected]> writes:
> > During boot, I get the message:
> >
> > PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> > using pci=biosirq.
>
> Can you send me 'lspci -vvx' output, please?
>
i am not the original poster, but i get the same message (save for the
device number), i.e. "PCI: No IRQ known for interrupt pin A of device
05:00.0. Please try using pci=biosirq". this is on a dell latitude
running 2.4.0-test11-pre7. the output from 'lspci -vvx' follows:
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
00: 86 80 92 71 06 01 00 a2 02 00 00 06 00 20 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:02.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation MagicGraph 128XD
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fde00000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M]
00: c8 10 04 00 03 00 80 02 01 00 00 03 00 20 00 00
10: 08 00 00 e0 00 00 e0 fd 00 00 d0 fd 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 74 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 10 ff
00:03.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 0074
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 a8 82 00
10: 00 00 00 10 00 00 00 02 00 01 01 b0 00 00 40 10
20: 00 f0 7f 10 00 00 80 10 00 f0 bf 10 00 10 00 00
30: fc 10 00 00 00 14 00 00 fc 14 00 00 0b 01 c0 05
40: 28 10 74 00 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:03.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 0074
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=05, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 a8 82 00
10: 00 10 00 10 00 00 00 02 00 05 05 b0 00 00 c0 10
20: 00 f0 ff 10 00 00 00 11 00 f0 3f 11 00 18 00 00
30: fc 18 00 00 00 1c 00 00 fc 1c 00 00 0b 02 00 05
40: 28 10 74 00 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 01 80 02 01 00 80 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 0860 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 61 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ece0 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: e1 ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 86 80 13 71 03 00 80 02 01 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
05:00.0 Ethernet controller: 3Com Corporation 3c575 [Megahertz] 10/100 LAN CardBus (rev 01)
Subsystem: 3Com Corporation 3C575 Megahertz 10/100 LAN Cardbus PC Card
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1800 [size=128]
Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10c00000 [size=128K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b7 10 57 51 07 00 10 02 01 00 00 02 00 40 00 00
10: 01 18 00 00 00 00 00 11 80 00 00 11 00 00 00 00
20: 00 00 00 00 00 00 00 00 90 00 00 00 b7 10 57 5b
30: 01 00 c0 10 50 00 00 00 00 00 00 00 0b 01 00 00
if i bring up the eth0 interface by hand the card works fine and i can
connect to the network.
--alex--
--
| I believe the moment is at hand when, by a paranoiac and active |
| advance of the mind, it will be possible (simultaneously with |
| automatism and other passive states) to systematize confusion |
| and thus to help to discredit completely the world of reality. |
On Sun, Nov 19, 2000 at 08:20:33PM +0100, Martin Mares wrote:
> > During boot, I get the message:
> >
> > PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> > using pci=biosirq.
>
> Can you send me 'lspci -vvx' output, please?
>
Here you go:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 530 Host (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at ec000000 (32-bit, non-prefetchable)
Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00: 39 10 30 05 07 00 10 22 03 00 00 06 00 20 80 00
10: 00 00 00 ec 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS]: Unknown device 5513
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 set
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 01f0
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0
00: 39 10 13 55 05 00 00 00 d0 80 01 01 00 80 80 00
10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 39 10 13 55
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00: 39 10 08 00 0f 00 00 02 b1 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.1 Class ff00: Silicon Integrated Systems [SiS] ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 39 10 09 00 00 00 00 02 00 00 00 ff 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 11) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 max, 32 set
Interrupt: pin A routed to IRQ 9
Region 0: Memory at efffe000 (32-bit, non-prefetchable)
00: 39 10 01 70 17 01 80 02 11 10 03 0c 00 20 80 00
10: 00 e0 ff ef 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 50
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ebe00000-ebefffff
Prefetchable memory behind bridge: fec00000-ffcfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00: 39 10 01 00 07 00 00 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 c0 c0 00 00
20: e0 eb e0 eb c0 fe c0 ff 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00
00:0b.0 Ethernet controller: Davicom Semiconductor, Inc. Ethernet 100/10 MBit (rev 10)
Subsystem: Unknown device 0291:8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 20 min, 40 max, 32 set
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at da00
Region 1: Memory at efffff80 (32-bit, non-prefetchable)
Expansion ROM at eff80000 [disabled]
Capabilities: [50] Power Management version 1
Flags: PMEClk- AuxPwr+ DSI+ D1- D2- PME-
Status: D0 PME-Enable+ DSel=0 DScale=0 PME+
00: 82 12 02 91 07 01 90 02 10 00 00 02 00 20 00 00
10: 01 da 00 00 80 ff ff ef 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 91 02 12 82
30: 00 00 f8 ef 50 00 00 00 00 00 00 00 0a 01 14 28
00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc: Unknown device 0111
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 2 min, 24 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: f6 13 11 01 05 01 10 02 10 00 01 04 00 20 80 00
10: 01 dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 01
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0b 01 02 18
00:0c.1 Communication controller: C-Media Electronics Inc: Unknown device 0211 (rev 10)
Subsystem: C-Media Electronics Inc: Unknown device 0211
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at de00
Capabilities: [40] Power Management version 2
Flags: PMEClk+ AuxPwr- DSI- D1- D2+ PME+
Status: D3 PME-Enable+ DSel=0 DScale=0 PME+
00: f6 13 11 02 01 00 10 02 10 00 80 07 00 00 00 00
10: 01 de 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 02
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 00 00
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 6306 3D-AGP (rev a3) (prog-if 00 [VGA])
Subsystem: Silicon Integrated Systems [SiS]: Unknown device 6306
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 2 min, 32 set
Region 0: Memory at ff000000 (32-bit, prefetchable)
Region 1: Memory at ebef0000 (32-bit, non-prefetchable)
Region 2: I/O ports at cc00
Capabilities: [40] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 1.0
Status: RQ=1 SBA- 64bit- FW- Rate=21
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00: 39 10 06 63 07 00 30 02 a3 00 00 03 00 20 00 00
10: 08 00 00 ff 00 00 ef eb 01 cc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 06 63
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00
Hope its useful to you.
> During boot, I get the message:
>
> PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> using pci=biosirq.
It is related to VGA card (at least on my system).
Enabling 'Assign IRQ for VGA' in BIOS causes the message to disapear.
Pavel
That looks exactly like the message I get if I tell the bios not to assign
an interrupt to my video card.
Gerhard
On 19 Nov 2000, Alex Romosan wrote:
> Martin Mares <[email protected]> writes:
>
> > > During boot, I get the message:
> > >
> > > PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> > > using pci=biosirq.
> >
> > Can you send me 'lspci -vvx' output, please?
> >
>
> i am not the original poster, but i get the same message (save for the
> device number), i.e. "PCI: No IRQ known for interrupt pin A of device
> 05:00.0. Please try using pci=biosirq". this is on a dell latitude
> running 2.4.0-test11-pre7. the output from 'lspci -vvx' follows:
>
> 00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
> Latency: 32
> Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
> 00: 86 80 92 71 06 01 00 a2 02 00 00 06 00 20 00 00
> 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:02.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
> Subsystem: Dell Computer Corporation MagicGraph 128XD
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M]
> Region 1: Memory at fde00000 (32-bit, non-prefetchable) [size=2M]
> Region 2: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M]
> 00: c8 10 04 00 03 00 80 02 01 00 00 03 00 20 00 00
> 10: 08 00 00 e0 00 00 e0 fd 00 00 d0 fd 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 74 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 10 ff
>
> 00:03.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
> Subsystem: Dell Computer Corporation: Unknown device 0074
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168, cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
> Memory window 0: 10400000-107ff000 (prefetchable)
> Memory window 1: 10800000-10bff000
> I/O window 0: 00001000-000010ff
> I/O window 1: 00001400-000014ff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
> 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 a8 82 00
> 10: 00 00 00 10 00 00 00 02 00 01 01 b0 00 00 40 10
> 20: 00 f0 7f 10 00 00 80 10 00 f0 bf 10 00 10 00 00
> 30: fc 10 00 00 00 14 00 00 fc 14 00 00 0b 01 c0 05
> 40: 28 10 74 00 01 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:03.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
> Subsystem: Dell Computer Corporation: Unknown device 0074
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168, cache line size 08
> Interrupt: pin B routed to IRQ 11
> Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=176
> Memory window 0: 10c00000-10fff000 (prefetchable)
> Memory window 1: 11000000-113ff000
> I/O window 0: 00001800-000018ff
> I/O window 1: 00001c00-00001cff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
> 16-bit legacy interface ports at 0001
> 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 a8 82 00
> 10: 00 10 00 10 00 00 00 02 00 05 05 b0 00 00 c0 10
> 20: 00 f0 ff 10 00 00 00 11 00 f0 3f 11 00 18 00 00
> 30: fc 18 00 00 00 1c 00 00 fc 1c 00 00 0b 02 00 05
> 40: 28 10 74 00 01 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> 00: 86 80 10 71 0f 01 80 02 01 00 80 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Region 4: I/O ports at 0860 [size=16]
> 00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 61 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Interrupt: pin D routed to IRQ 11
> Region 4: I/O ports at ece0 [size=32]
> 00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: e1 ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
>
> 00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 86 80 13 71 03 00 80 02 01 00 80 06 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 05:00.0 Ethernet controller: 3Com Corporation 3c575 [Megahertz] 10/100 LAN CardBus (rev 01)
> Subsystem: 3Com Corporation 3C575 Megahertz 10/100 LAN Cardbus PC Card
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 1800 [size=128]
> Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
> Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at 10c00000 [size=128K]
> Capabilities: [50] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: b7 10 57 51 07 00 10 02 01 00 00 02 00 40 00 00
> 10: 01 18 00 00 00 00 00 11 80 00 00 11 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 90 00 00 00 b7 10 57 5b
> 30: 01 00 c0 10 50 00 00 00 00 00 00 00 0b 01 00 00
>
> if i bring up the eth0 interface by hand the card works fine and i can
> connect to the network.
>
> --alex--
>
> --
> | I believe the moment is at hand when, by a paranoiac and active |
> | advance of the mind, it will be possible (simultaneously with |
> | automatism and other passive states) to systematize confusion |
> | and thus to help to discredit completely the world of reality. |
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> Please read the FAQ at http://www.tux.org/lkml/
>
--
Gerhard Mack
[email protected]
<>< As a computer I find your faith in technology amusing.
Gerhard Mack <[email protected]> writes:
> That looks exactly like the message I get if I tell the bios not to
> assign an interrupt to my video card.
>
unfortunately, i don't get such a choice. and if what you say is true,
isn't the message ("No IRQ known for interrupt pin A of device
05:00.0. Please try using pci=biosirq") misleading? to me this means
the kernel couldn't find the irq by itself, so it will ask the bios.
but if the irq is not assigned in the bios, how can kernel find it
then? maybe i should look at the code itself to try to understand what
is going on here (chances are i won't understand the code anyway, so
that's why i'm asking).
--alex--
--
| I believe the moment is at hand when, by a paranoiac and active |
| advance of the mind, it will be possible (simultaneously with |
| automatism and other passive states) to systematize confusion |
| and thus to help to discredit completely the world of reality. |
I'm getting the same message with 2.4.0-test10 on a sis chipset. There
doesn't seam to be any other problems, and ide0 appears in
/proc/interrupts.
# dmesg |grep ^PCI
PCI: PCI BIOS revision 2.10 entry at 0xfdb91, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 00:14.0
PCI: Cannot allocate resource region 1 of device 00:14.0
PCI: Cannot allocate resource region 2 of device 00:14.0
PCI: No IRQ known for interrupt pin A of device 00:01.1. Please try using pci=biosirq.
PCI: Setting latency timer of device 00:0b.0 to 32
PCI: Setting latency timer of device 00:09.0 to 32
# lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 5597 [SiS5582] (rev 10)
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev 01)
00:01.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:09.0 Multimedia audio controller: Trident Microsystems 4DWave NX (rev 02)
00:0b.0 Ethernet controller: D-Link System Inc: Unknown device 1002
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 (rev 02)
00:0f.0 VGA compatible controller: Cirrus Logic GD 5430/40 [Alpine] (rev 22)
00:14.0 VGA compatible controller: Silicon Integrated Systems [SiS] 5597/5598 VGA (rev 68)
# lspci -vvx
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 5597 [SiS5582] (rev 10)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00: 39 10 97 55 07 00 00 22 10 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 39 10 08 00 07 00 00 02 01 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 8a [Master SecP PriP])
Subsystem: Unknown device 0149:0100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 4000 [size=16]
00: 39 10 13 55 07 00 00 00 d0 8a 01 01 00 80 80 00
10: 01 00 2c 13 21 84 00 00 a1 c2 00 03 19 02 84 08
20: 01 40 00 00 00 00 00 00 00 00 00 00 49 01 00 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:09.0 Multimedia audio controller: Trident Microsystems 4DWave NX (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f400 [size=256]
Region 1: Memory at ffadf000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 23 10 01 20 07 01 10 02 02 00 01 04 00 20 00 00
10: 01 f4 00 00 00 f0 ad ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 48 00 00 00 00 00 00 00 0b 01 02 05
00:0b.0 Ethernet controller: D-Link System Inc: Unknown device 1002
Subsystem: D-Link System Inc: Unknown device 1002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 04
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at f080 [size=128]
Region 1: Memory at ffafff80 (32-bit, non-prefetchable) [size=128]
Expansion ROM at ffae0000 [disabled] [size=64K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00: 86 11 02 10 17 01 10 02 00 00 00 02 04 20 00 00
10: 81 f0 00 00 80 ff af ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 02 10
30: 00 00 ae ff 50 00 00 00 00 00 00 00 0a 01 0a 0a
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fd9fe000 (32-bit, prefetchable) [size=4K]
00: 9e 10 6e 03 06 01 80 02 02 00 00 04 00 40 80 00
10: 08 e0 9f fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 70 00 eb 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 10 28
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fd9ff000 (32-bit, prefetchable) [size=4K]
00: 9e 10 78 08 06 01 80 02 02 00 80 04 00 40 80 00
10: 08 f0 9f fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 70 00 eb 13
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 04 ff
00:0f.0 VGA compatible controller: Cirrus Logic GD 5430/40 [Alpine] (rev 22) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Expansion ROM at fe000000 [disabled] [size=16M]
00: 13 10 a0 00 23 00 00 02 22 00 00 03 00 00 00 00
10: 08 00 00 fc 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 fe 00 00 00 00 00 00 00 00 ff 00 00 00
00:14.0 VGA compatible controller: Silicon Integrated Systems [SiS] 5597/5598 VGA (rev 68) (prog-if 00 [VGA])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 10000000 (32-bit, prefetchable) [disabled] [size=4M]
Region 1: Memory at 10400000 (32-bit, non-prefetchable) [disabled] [size=64K]
Region 2: I/O ports at <ignored> [disabled] [size=128]
Expansion ROM at ffff8000 [disabled] [size=32K]
00: 39 10 00 02 00 00 00 02 68 00 00 03 00 00 00 00
10: 08 00 00 10 00 00 40 10 81 ff ff ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 80 ff ff 00 00 00 00 00 00 00 00 00 01 00 00
portable:~#
Script done on Tue Nov 21 15:02:15 2000
--
Rob Murray