Hello,
with todays git I lots of these warnings:
[ 1.246807] ata1.00: ATA-7: ST910021AS, 4.06, max UDMA/100
[ 1.253066] ata1.00: 195371568 sectors, multi 16: LBA48
[ 1.262561] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-U10N, 1.05, max UDMA/33
[ 1.273159] ata1.00: configured for UDMA/100
[ 1.275279] ata2.00: configured for UDMA/33
[ 1.285546] scsi 0:0:0:0: Direct-Access ATA ST910021AS 4.06 PQ: 0 ANSI: 5
[ 1.292049] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.298427] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
[ 1.299631] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
[ 1.311059] sd 0:0:0:0: [sda] Write Protect is off
[ 1.317409] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.317426] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.318378] ------------[ cut here ]------------
[ 1.318380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
[ 1.318381] Hardware name: 64575GG
[ 1.318382] Modules linked in:
[ 1.318384] Pid: 0, comm: swapper Not tainted 2.6.28-self-07939-g2150edc #66
[ 1.318386] Call Trace:
[ 1.318390] [<c05412ac>] ? printk+0x18/0x1a
[ 1.318393] [<c014c803>] warn_slowpath+0x73/0xd0
[ 1.318397] [<c02b370f>] ? blk_complete_request+0x1f/0x30
[ 1.318399] [<c03857ab>] ? scsi_done+0xb/0x10
[ 1.318401] [<c03a49d4>] ? atapi_qc_complete+0x64/0x310
[ 1.318405] [<c039cd94>] ? __ata_qc_complete+0x64/0xd0
[ 1.318407] [<c039e565>] ? ata_qc_complete+0x95/0x1d0
[ 1.318409] [<c014863b>] ? default_wake_function+0xb/0x10
[ 1.318411] [<c03ad8f5>] ? ata_sff_data_xfer32+0x75/0xc0
[ 1.318413] [<c03ad40e>] ata_sff_hsm_move+0x45e/0x750
[ 1.318416] [<c03ae99a>] ata_sff_interrupt+0x14a/0x220
[ 1.318419] [<c017cd49>] handle_IRQ_event+0x39/0x70
[ 1.318421] [<c017e548>] handle_edge_irq+0xa8/0x130
[ 1.318423] [<c017e4a0>] ? handle_edge_irq+0x0/0x130
[ 1.318425] <IRQ> [<c0151885>] ? irq_exit+0x75/0x90
[ 1.318429] [<c0120ae7>] ? common_interrupt+0x27/0x2c
[ 1.318432] [<c0127902>] ? mwait_idle+0x42/0x50
[ 1.318434] [<c011ec01>] ? cpu_idle+0x71/0xd0
[ 1.318437] [<c053e704>] ? start_secondary+0x18f/0x1fb
[ 1.318440] [<c0538084>] ? i8042_probe+0x586/0x5fa
[ 1.318444] ---[ end trace d41a74a84afec9c1 ]---
cborntra@cborntra:/sys/bus/scsi$ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: ST910021AS Rev: 4.06
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: HL-DT-ST Model: DVDRAM GSA-U10N Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 05
Christian
On Fri, 9 Jan 2009 13:34:55 +0100
Christian Borntraeger <[email protected]> wrote:
> Hello,
>
> with todays git I lots of these warnings:
>
> [ 1.246807] ata1.00: ATA-7: ST910021AS, 4.06, max UDMA/100
> [ 1.253066] ata1.00: 195371568 sectors, multi 16: LBA48
> [ 1.262561] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-U10N, 1.05, max UDMA/33
> [ 1.273159] ata1.00: configured for UDMA/100
> [ 1.275279] ata2.00: configured for UDMA/33
> [ 1.285546] scsi 0:0:0:0: Direct-Access ATA ST910021AS 4.06 PQ: 0 ANSI: 5
> [ 1.292049] sd 0:0:0:0: Attached scsi generic sg0 type 0
> [ 1.298427] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
> [ 1.299631] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
> [ 1.311059] sd 0:0:0:0: [sda] Write Protect is off
> [ 1.317409] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 1.317426] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 1.318378] ------------[ cut here ]------------
> [ 1.318380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
> [ 1.318381] Hardware name: 64575GG
Can you see if this goes away if you back out all Arjan's async stuff.
Then if not can you back out my 32bit PIO patch and see if that is the
trigger.
Alan
Am Freitag, 9. Januar 2009 schrieb Alan Cox:
> On Fri, 9 Jan 2009 13:34:55 +0100
> Christian Borntraeger <[email protected]> wrote:
>
> > Hello,
> >
> > with todays git I lots of these warnings:
> >
> > [ 1.246807] ata1.00: ATA-7: ST910021AS, 4.06, max UDMA/100
> > [ 1.253066] ata1.00: 195371568 sectors, multi 16: LBA48
> > [ 1.262561] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-U10N, 1.05, max UDMA/33
> > [ 1.273159] ata1.00: configured for UDMA/100
> > [ 1.275279] ata2.00: configured for UDMA/33
> > [ 1.285546] scsi 0:0:0:0: Direct-Access ATA ST910021AS 4.06 PQ: 0 ANSI: 5
> > [ 1.292049] sd 0:0:0:0: Attached scsi generic sg0 type 0
> > [ 1.298427] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
> > [ 1.299631] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
> > [ 1.311059] sd 0:0:0:0: [sda] Write Protect is off
> > [ 1.317409] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> > [ 1.317426] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > [ 1.318378] ------------[ cut here ]------------
> > [ 1.318380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
> > [ 1.318381] Hardware name: 64575GG
>
> Can you see if this goes away if you back out all Arjan's async stuff.
> Then if not can you back out my 32bit PIO patch and see if that is the
> trigger.
>
> Alan
Sure.
Since I could not revert arjans patches without conflicts, I started
checking out older versions. My first try was
e427fe042cf90c0652eed9a85e57a8fd8af89890 (without PIO, with async patched)
was successful. The problem went away. So it was triggered by the 32bit PIO patch.
Do you still need a test result without the async patches?
Christian
Am Freitag 09 Januar 2009 schrieb Alan Cox:
> On Fri, 9 Jan 2009 13:34:55 +0100
> Christian Borntraeger <[email protected]> wrote:
>
> > Hello,
> >
> > with todays git I lots of these warnings:
> >
> > [ 1.246807] ata1.00: ATA-7: ST910021AS, 4.06, max UDMA/100
> > [ 1.253066] ata1.00: 195371568 sectors, multi 16: LBA48
> > [ 1.262561] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-U10N, 1.05, max UDMA/33
> > [ 1.273159] ata1.00: configured for UDMA/100
> > [ 1.275279] ata2.00: configured for UDMA/33
> > [ 1.285546] scsi 0:0:0:0: Direct-Access ATA ST910021AS 4.06 PQ: 0 ANSI: 5
> > [ 1.292049] sd 0:0:0:0: Attached scsi generic sg0 type 0
> > [ 1.298427] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors: (100 GB/93.1 GiB)
> > [ 1.299631] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
> > [ 1.311059] sd 0:0:0:0: [sda] Write Protect is off
> > [ 1.317409] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> > [ 1.317426] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > [ 1.318378] ------------[ cut here ]------------
> > [ 1.318380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
> > [ 1.318381] Hardware name: 64575GG
>
> Can you see if this goes away if you back out all Arjan's async stuff.
> Then if not can you back out my 32bit PIO patch and see if that is the
> trigger.
I did some printk debugging.
__atapi_pio_bytes is called with bytes=18. That means with 32bit transfers
there is a 2 byte trailing transfer, which triggers this WARN_ON.
Christian
> I did some printk debugging.
> __atapi_pio_bytes is called with bytes=18. That means with 32bit transfers
> there is a 2 byte trailing transfer, which triggers this WARN_ON.
Ouch.. that means all that someone issued a multiple segment data
transfer with a 2 byte aligned chunk in the middle.
That is a bit of a suprise because we set blk_queue_dma_alignment to 3 so
the block layer should never hand us an sg list in that form. That means
we've either got a block layer bug or someone somewhere is generating
invalid sg lists internally to libata.
Can you dump qc->cdb[] and see what command is getting issued in the
broken form ?
Alan
Am Samstag 10 Januar 2009 schrieb Alan Cox:
> > I did some printk debugging.
> > __atapi_pio_bytes is called with bytes=18. That means with 32bit transfers
> > there is a 2 byte trailing transfer, which triggers this WARN_ON.
>
> Ouch.. that means all that someone issued a multiple segment data
> transfer with a 2 byte aligned chunk in the middle.
>
> That is a bit of a suprise because we set blk_queue_dma_alignment to 3 so
> the block layer should never hand us an sg list in that form. That means
> we've either got a block layer bug or someone somewhere is generating
> invalid sg lists internally to libata.
>
> Can you dump qc->cdb[] and see what command is getting issued in the
> broken form ?
I instrumented __atapi_pio_bytes to print some variables. This is the dump of
the first two:
[ 1.484730] count: 36 sg->length: 36 qc->cursg_ofs: 0 bytes: 36
[ 1.485709] qc->cdb[]:12000000240000000000000000000000
That works fine.
[ 1.499843] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
[ 1.508389] count: 18 sg->length: 96 qc->cursg_ofs: 0 bytes: 18
[ 1.509369] qc->cdb[]:03000000600000000000000000000000
That one is broken.
[ 1.509369] ------------[ cut here ]------------
[ 1.509369] WARNING: at drivers/ata/libata-sff.c:1024 ata_sff_hsm_move+0x69b/0x810()
Hello.
Christian Borntraeger wrote:
>>> I did some printk debugging.
>>> __atapi_pio_bytes is called with bytes=18. That means with 32bit transfers
>>> there is a 2 byte trailing transfer, which triggers this WARN_ON.
>>>
>> Ouch.. that means all that someone issued a multiple segment data
>> transfer with a 2 byte aligned chunk in the middle.
>>
>> That is a bit of a suprise because we set blk_queue_dma_alignment to 3 so
>> the block layer should never hand us an sg list in that form. That means
>> we've either got a block layer bug or someone somewhere is generating
>> invalid sg lists internally to libata.
>>
>> Can you dump qc->cdb[] and see what command is getting issued in the
>> broken form ?
>>
>
> I instrumented __atapi_pio_bytes to print some variables. This is the dump of
> the first two:
>
> [ 1.484730] count: 36 sg->length: 36 qc->cursg_ofs: 0 bytes: 36
> [ 1.485709] qc->cdb[]:12000000240000000000000000000000
> That works fine.
>
That's the typical INQUIRY command with 36-byte data length.
> [ 1.499843] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N 1.05 PQ: 0 ANSI: 5
> [ 1.508389] count: 18 sg->length: 96 qc->cursg_ofs: 0 bytes: 18
> [ 1.509369] qc->cdb[]:03000000600000000000000000000000
> That one is broken.
>
That's the typical REQUEST SENSE command with 18-byte data length.
MBR, Sergei
> That's the typical REQUEST SENSE command with 18-byte data length.
Which means something has become horribly broken in the core libata stack.
An 18 byte inquiry would have 18 bytes as the *last* sg element. That
would therefore not trigger the WARN_ON. Someone has passed an sg list
that isn't properly terminated perhaps ?
I wonder if the pad code broke this.
Hello.
Alan Cox wrote:
>> That's the typical REQUEST SENSE command with 18-byte data length.
> Which means something has become horribly broken in the core libata stack.
> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
Did you get me right? 18 bytes is the typical REQUEST SENSE payload
(libata requested 96 bytes), not INQUIRY. For the INQUIRY 36 bytes was
requested and received (divisible by 4).
And I doubt there can be more than one S/G segment with such lengths...
WBR, Sergei
Am Samstag 10 Januar 2009 schrieb Alan Cox:
> > That's the typical REQUEST SENSE command with 18-byte data length.
>
> Which means something has become horribly broken in the core libata stack.
> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
> would therefore not trigger the WARN_ON. Someone has passed an sg list
> that isn't properly terminated perhaps ?
>
> I wonder if the pad code broke this.
I just checked 2.6.28 + PIO32 patch. Its also broken. Whatever caused this
problem did it a while ago.
I am wondering if I am the only one seeing this problem.
* Alan Cox <[email protected]> wrote:
> > That's the typical REQUEST SENSE command with 18-byte data length.
>
> Which means something has become horribly broken in the core libata
> stack. An 18 byte inquiry would have 18 bytes as the *last* sg element.
> That would therefore not trigger the WARN_ON. Someone has passed an sg
> list that isn't properly terminated perhaps ?
>
> I wonder if the pad code broke this.
note, one of my testboxes in the -tip testing hw pool (an older HP laptop)
started triggering this too today:
[ 3.834413] PM: Adding info for No Bus:8:0
[ 3.835116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.835237] driver: '0:0:0:0': driver_bound: bound to device 'sd'
[ 3.835249] bus: 'scsi': really_probe: bound device 0:0:0:0 to driver sd
[ 3.835272] device: '0:0:0:0': device_add
[ 3.835374] PM: Adding info for No Bus:0:0:0:0
[ 4.112738] ata2.00: ATAPI: QSI DVD-ROM SDR-081, EHA8, max UDMA/33
[ 4.120617] ata2.00: configured for UDMA/33
[ 4.121275] ------------[ cut here ]------------
[ 4.121380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x3d9/0x840()
[ 4.121538] Hardware name: HP OmniBook PC
[ 4.121644] Pid: 0, comm: swapper Not tainted 2.6.28-tip-10029-g20e9954-dirty #3
[ 4.121798] Call Trace:
[ 4.121912] [<c013d006>] warn_slowpath+0x86/0xa0
[ 4.122030] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122136] [<c0133270>] ? default_wake_function+0x10/0x20
[ 4.122260] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.122368] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122490] [<c06513d3>] ? ata_qc_complete_internal+0x13/0x20
[ 4.122602] [<c064f6ed>] ? __ata_qc_complete+0x6d/0xe0
[ 4.122710] [<c065e0a9>] ? ata_sff_qc_fill_rtf+0x19/0x30
[ 4.122817] [<c065fa07>] ? ata_sff_data_xfer32+0x77/0xd0
[ 4.122923] [<c0660739>] ata_sff_hsm_move+0x3d9/0x840
[ 4.123029] [<c034eb06>] ? _raw_spin_lock+0x46/0x170
[ 4.123134] [<c0660ef9>] ata_sff_interrupt+0x129/0x1e0
[ 4.123246] [<c0171dc0>] handle_IRQ_event+0x30/0x70
[ 4.123354] [<c0173b05>] handle_level_irq+0x75/0xe0
[ 4.123459] [<c0173a90>] ? handle_level_irq+0x0/0xe0
[ 4.123562] <IRQ> [<c0104607>] ? common_interrupt+0x27/0x2c
[ 4.123725] [<c0120120>] ? native_safe_halt+0x0/0x10
[ 4.123830] [<c012012a>] ? native_safe_halt+0xa/0x10
[ 4.123942] [<c010aaf9>] ? default_idle+0x69/0xa0
[ 4.124053] [<c015f792>] ? tick_nohz_restart_sched_tick+0x32/0x1b0
[ 4.124167] [<c011715f>] ? apm_cpu_idle+0xdf/0x260
[ 4.124273] [<c01027d8>] ? cpu_idle+0x78/0x100
[ 4.124379] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.124490] [<c09a92b3>] ? rest_init+0x53/0x60
[ 4.124601] [<c0e4d82a>] ? start_kernel+0x2ba/0x360
[ 4.124709] [<c0e4d260>] ? unknown_bootoption+0x0/0x210
[ 4.124820] [<c0e4d07c>] ? i386_start_kernel+0x7c/0xb0
[ 4.124948] ---[ end trace 83f9033b42a87df9 ]---
[ 4.126783] scsi 1:0:0:0: CD-ROM QSI DVD-ROM SDR-081 EHA8 PQ: 0 ANSI: 5
[ 4.126979] device: 'target1:0:0': device_add
[ 4.127040] PM: Adding info for No Bus:target1:0:0
[ 4.127057] device: '1:0:0:0': device_add
[ 4.127191] bus: 'scsi': add device 1:0:0:0
[ 4.127235] PM: Adding info for scsi:1:0:0:0
[ 4.127994] bus: 'scsi': driver_probe_device: matched device 1:0:0:0 with driver osst
it did manage to boot up and it appears to limp along. Full bootlog below,
config attached.
last-known-good: 9e42d0cf5020aaf217433cad1a224745241d212a
first-known-bad: 9a100a4464917b5ffff3a8ce1c2758088fd9bb32
Which implicates one of these commits:
a3a798c: Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
efcb3cf: libata: use WARN_ON_ONCE on hot paths
b2576e1: Merge branch 'linus' into release
0fe40ff: libata: clean up the SFF code for coding style
871af12: libata: Add 32bit PIO support
e427fe0: [libata] ahci: Withdraw IGN_SERR_INTERNAL for SB800 SATA
6ecb6f2: pata_hpt366: reimplement mode programming
b63d395: [libata] pata_hpt3x3: correct _freeze() function declaration
5c18c4d: libata: Add special ata_pio_need_iordy() handling for Compact Flash.
78a7ba4: pata_platform: __pata_platform_remove() shouldn't be in discard section
1564a18: sata_sil24: remove unused sil24_port_multiplier
8522ee2: [libata] ahci: Add SATA GEN3 related messages
2852bcf: ata_piix: save, use saved and restore IOCFG
fc80902: pata_ali: Fix and workaround for FIFO DMA bug
1b2c357: pata_ali: force initialise a few bits
978ff6d: pata_hpt3x3: Workarounds for chipset
ea7e96e: ACPI: remove private acpica headers from driver files
Ingo
-------------------->
[ 0.000000] Linux version 2.6.28-tip-10029-g20e9954-dirty (mingo@mazsi) (gcc version 4.2.2) #3 SMP Sat Jan 10 13:49:31 CET 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] PAT WC disabled due to known CPU erratum.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e8400 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001ffffc00 (ACPI data)
[ 0.000000] BIOS-e820: 000000001ffffc00 - 0000000020000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.3 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] last_pfn = 0x1fff0 max_arch_pfn = 0x100000
[ 0.000000] kernel direct mapping tables up to 1fff0000 @ 10000-16000
[ 0.000000] RAMDISK: 1fd4d000 - 1ffdfef8
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1fff0000
[ 0.000000] low ram: 00000000 - 1fff0000
[ 0.000000] bootmap 00012000 - 00016000
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001fff0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 0001401954] TEXT DATA BSS ==> [0000100000 - 0001401954]
[ 0.000000] #4 [001fd4d000 - 001ffdfef8] RAMDISK ==> [001fd4d000 - 001ffdfef8]
[ 0.000000] #5 [0001402000 - 0001409000] INIT_PG_TABLE ==> [0001402000 - 0001409000]
[ 0.000000] #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #7 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] #8 [0000012000 - 0000016000] BOOTMAP ==> [0000012000 - 0000016000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001fff0
[ 0.000000] HighMem 0x0001fff0 -> 0x0001fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001fff0
[ 0.000000] On node 0 totalpages: 130943
[ 0.000000] free_area_init_node: node 0, pgdat c0e1e640, node_mem_map c1409340
[ 0.000000] DMA zone: 52 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3931 pages, LIFO batch:0
[ 0.000000] Normal zone: 1612 pages used for memmap
[ 0.000000] Normal zone: 125348 pages, LIFO batch:31
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e9000
[ 0.000000] PM: Registered nosave memory: 00000000000e9000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129279
[ 0.000000] Kernel command line:
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] CPU 0 irqstacks, hard=c0ef5000 soft=c0eed000
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] TSC: Using PIT calibration value
[ 0.000000] Detected 738.822 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.004000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.004000] ... MAX_LOCK_DEPTH: 48
[ 0.004000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.004000] ... CLASSHASH_SIZE: 4096
[ 0.004000] ... MAX_LOCKDEP_ENTRIES: 8192
[ 0.004000] ... MAX_LOCKDEP_CHAINS: 16384
[ 0.004000] ... CHAINHASH_SIZE: 8192
[ 0.004000] memory used by lock dependency info: 2335 kB
[ 0.004000] per task-struct memory footprint: 1152 bytes
[ 0.004000] ------------------------
[ 0.004000] | Locking API testsuite:
[ 0.004000] ----------------------------------------------------------------------------
[ 0.004000] | spin |wlock |rlock |mutex | wsem | rsem |
[ 0.004000] --------------------------------------------------------------------------
[ 0.004000] A-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-B-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-B-C-C-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-C-A-B-C deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-B-C-C-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-C-D-B-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] A-B-C-D-B-C-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.004000] double unlock: ok | ok | ok | ok | ok | ok |
[ 0.004000] initialize held: ok | ok | ok | ok | ok | ok |
[ 0.004000] bad unlock order: ok | ok | ok | ok | ok | ok |
[ 0.004000] --------------------------------------------------------------------------
[ 0.004000] recursive read-lock: | ok | |failed|
[ 0.004000] recursive read-lock #2: | ok | |failed|
[ 0.004000] mixed read-write-lock: |failed| |failed|
[ 0.004000] mixed write-read-lock: |failed| |failed|
[ 0.004000] --------------------------------------------------------------------------
[ 0.004000] hard-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.004000] soft-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.004000] hard-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.004000] soft-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.004000] sirq-safe-A => hirqs-on/12:failed|failed| ok |
[ 0.004000] sirq-safe-A => hirqs-on/21:failed|failed| ok |
[ 0.004000] hard-safe-A + irqs-on/12:failed|failed| ok |
[ 0.004000] soft-safe-A + irqs-on/12:failed|failed| ok |
[ 0.004000] hard-safe-A + irqs-on/21:failed|failed| ok |
[ 0.004000] soft-safe-A + irqs-on/21:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.004000] hard-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.004000] soft-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/123:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/123:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/132:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/132:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/213:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/213:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/231:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/231:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/312:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/312:failed|failed| ok |
[ 0.004000] hard-irq lock-inversion/321:failed|failed| ok |
[ 0.004000] soft-irq lock-inversion/321:failed|failed| ok |
[ 0.004000] hard-irq read-recursion/123: ok |
[ 0.004000] soft-irq read-recursion/123: ok |
[ 0.004000] hard-irq read-recursion/132: ok |
[ 0.004000] soft-irq read-recursion/132: ok |
[ 0.004000] hard-irq read-recursion/213: ok |
[ 0.004000] soft-irq read-recursion/213: ok |
[ 0.004000] hard-irq read-recursion/231: ok |
[ 0.004000] soft-irq read-recursion/231: ok |
[ 0.004000] hard-irq read-recursion/312: ok |
[ 0.004000] soft-irq read-recursion/312: ok |
[ 0.004000] hard-irq read-recursion/321: ok |
[ 0.004000] soft-irq read-recursion/321: ok |
[ 0.004000] --------------------------------------------------------
[ 0.004000] 133 out of 218 testcases failed, as expected. |
[ 0.004000] ----------------------------------------------------
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 494256k/524224k available (9280k kernel code, 29332k reserved, 4301k data, 628k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffee1000 - 0xfffff000 (1144 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xe07f0000 - 0xff7fe000 ( 496 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 0.004000] .init : 0xc0e4d000 - 0xc0eea000 ( 628 kB)
[ 0.004000] .data : 0xc0a102c0 - 0xc0e43824 (4301 kB)
[ 0.004000] .text : 0xc0100000 - 0xc0a102c0 (9280 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.004041] Calibrating delay loop (skipped), value calculated using timer frequency.. 1477.64 BogoMIPS (lpj=2955288)
[ 0.004452] Security Framework initialized
[ 0.004782] Mount-cache hash table entries: 512
[ 0.006575] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 0.006726] CPU: L2 cache: 256K
[ 0.006904] Checking 'hlt' instruction... OK.
[ 0.022350] SMP alternatives: switching to UP code
[ 1.160176] Freeing SMP alternatives: 29k freed
[ 1.160317] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 1.160449] ftrace: allocating 23916 entries in 94 pages
[ 1.169618] weird, boot CPU (#0) not listed by the BIOS.
[ 1.169753] SMP motherboard not detected.
[ 1.169855] Local APIC not detected. Using dummy APIC emulation.
[ 1.169961] SMP disabled
[ 1.184891] Brought up 1 CPUs
[ 1.185028] Total of 1 processors activated (1477.64 BogoMIPS).
[ 1.185327] CPU0 attaching NULL sched-domain.
[ 1.186431] device: 'platform': device_add
[ 1.186549] PM: Adding info for No Bus:platform
[ 1.187632] khelper used greatest stack depth: 3248 bytes left
[ 1.188132] bus: 'platform': registered
[ 1.188160] Registering sysdev class 'cpu'
[ 1.189674] net_namespace: 696 bytes
[ 1.190194] Booting paravirtualized kernel on bare hardware
[ 1.191935] xor: automatically using best checksumming function: pIII_sse
[ 1.212017] pIII_sse : 1491.000 MB/sec
[ 1.212120] xor: using function: pIII_sse (1491.000 MB/sec)
[ 1.212236] regulator: core version 0.5
[ 1.212332] device class 'regulator': registering
[ 1.212938] Time: 13:50:57 Date: 01/10/09
[ 1.213702] bus: 'virtio': registered
[ 1.214180] NET: Registered protocol family 16
[ 1.214439] device class 'bdi': registering
[ 1.215439] device class 'gpio': registering
[ 1.216291] device class 'pci_bus': registering
[ 1.217638] bus: 'pci': registered
[ 1.217653] device class 'lcd': registering
[ 1.218201] device class 'backlight': registering
[ 1.218747] device class 'video_output': registering
[ 1.219279] device class 'tty': registering
[ 1.219846] device class 'vtconsole': registering
[ 1.220720] device: 'vtcon0': device_add
[ 1.220861] PM: Adding info for No Bus:vtcon0
[ 1.222150] bus: 'spi': registered
[ 1.222160] device class 'spi_master': registering
[ 1.222787] khelper used greatest stack depth: 3184 bytes left
[ 1.223654] bus: 'i2c': registered
[ 1.223664] device class 'i2c-adapter': registering
[ 1.224258] bus: 'i2c': add driver dummy
[ 1.224896] i2c-core: driver [dummy] registered
[ 1.225097] device class 'dmi': registering
[ 1.225753] device: 'id': device_add
[ 1.225966] PM: Adding info for No Bus:id
[ 1.226705] device class 'dma': registering
[ 1.227380] dca service started, version 1.4
[ 1.227501] device class 'dca': registering
[ 1.231497] PCI: PCI BIOS revision 2.10 entry at 0xfd980, last bus=1
[ 1.231624] PCI: Using configuration type 1 for base access
[ 1.231764] Registering sys device of class 'cpu'
[ 1.231814] Registering sys device 'cpu0'
[ 1.233241] bus: 'MCA': registered
[ 1.710918] device: 'default': device_add
[ 1.711009] PM: Adding info for No Bus:default
[ 1.711778] bio: create slab <bio-0> at 0
[ 1.712535] device class 'block': registering
[ 1.713001] bus: 'spi': add driver max7301
[ 1.713790] bus: 'i2c': add driver max732x
[ 1.714394] i2c-core: driver [max732x] registered
[ 1.714412] bus: 'spi': add driver mcp23s08
[ 1.715019] bus: 'i2c': add driver pca953x
[ 1.715623] i2c-core: driver [pca953x] registered
[ 1.715641] bus: 'i2c': add driver pcf857x
[ 1.716939] i2c-core: driver [pcf857x] registered
[ 1.716962] bus: 'platform': add driver twl4030_gpio
[ 1.717744] device class 'graphics': registering
[ 1.718316] bus: 'platform': add driver bq24022
[ 1.718970] bus: 'platform': remove driver bq24022
[ 1.719526] driver: 'bq24022': driver_release
[ 1.719577] device class 'misc': registering
[ 1.720845] bus: 'i2c': add driver twl4030
[ 1.721503] khelper used greatest stack depth: 3180 bytes left
[ 1.721752] i2c-core: driver [twl4030] registered
[ 1.721767] device class 'mdio_bus': registering
[ 1.722970] bus: 'mdio_bus': registered
[ 1.722983] bus: 'mdio_bus': add driver Generic PHY
[ 1.723570] device class 'dvb': registering
[ 1.726052] device class 'scsi_host': registering
[ 1.727731] bus: 'scsi': registered
[ 1.727744] device class 'scsi_device': registering
[ 1.728650] SCSI subsystem initialized
[ 1.729316] libata version 3.00 loaded.
[ 1.729328] device class 'pcmcia_socket': registering
[ 1.730105] bus: 'platform': add driver twl4030_usb
[ 1.731605] bus: 'usb': registered
[ 1.731621] device class 'usb_host': registering
[ 1.733339] bus: 'usb': add driver usbfs
[ 1.734054] usbcore: registered new interface driver usbfs
[ 1.734212] bus: 'usb': add driver hub
[ 1.734790] usbcore: registered new interface driver hub
[ 1.735135] bus: 'usb': add driver usb
[ 1.735832] usbcore: registered new device driver usb
[ 1.736691] bus: 'serio': registered
[ 1.736911] device class 'input': registering
[ 1.737729] device class 'rtc': registering
[ 1.738401] device class 'power_supply': registering
[ 1.739012] device class 'hwmon': registering
[ 1.739612] device class 'thermal': registering
[ 1.741078] device class 'leds': registering
[ 1.741743] PCI: Probing PCI hardware
[ 1.741948] PCI: Probing PCI hardware (bus 00)
[ 1.741993] device: 'pci0000:00': device_add
[ 1.742052] PM: Adding info for No Bus:pci0000:00
[ 1.742067] device: '0000:00': device_add
[ 1.742146] PM: Adding info for No Bus:0000:00
[ 1.742923] pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
[ 1.743380] pci 0000:00:07.1: reg 20 io port: [0x1c20-0x1c2f]
[ 1.743535] pci 0000:00:07.2: reg 20 io port: [0x1c00-0x1c1f]
[ 1.743723] pci 0000:00:07.3: quirk: region 8000-803f claimed by PIIX4 ACPI
[ 1.743843] pci 0000:00:07.3: quirk: region 2180-218f claimed by PIIX4 SMB
[ 1.743967] pci 0000:00:07.3: PIIX4 devres E PIO at 0378-037f
[ 1.744042] pci 0000:00:07.3: PIIX4 devres I PIO at 0398-0399
[ 1.744263] pci 0000:00:0a.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 1.744316] pci 0000:00:0a.0: supports D1 D2
[ 1.744324] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.744439] pci 0000:00:0a.0: PME# disabled
[ 1.744632] pci 0000:00:0a.1: reg 10 32bit mmio: [0x000000-0x000fff]
[ 1.744683] pci 0000:00:0a.1: supports D1 D2
[ 1.744691] pci 0000:00:0a.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.744805] pci 0000:00:0a.1: PME# disabled
[ 1.745014] pci 0000:00:0b.0: reg 10 io port: [0x1000-0x10ff]
[ 1.745035] pci 0000:00:0b.0: reg 14 32bit mmio: [0xf4002400-0xf400247f]
[ 1.745056] pci 0000:00:0b.0: reg 18 32bit mmio: [0xf4002000-0xf400207f]
[ 1.745110] pci 0000:00:0b.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.745160] pci 0000:00:0b.0: supports D1 D2
[ 1.745168] pci 0000:00:0b.0: PME# supported from D1 D2 D3hot D3cold
[ 1.745280] pci 0000:00:0b.0: PME# disabled
[ 1.745470] pci 0000:00:0b.1: reg 10 io port: [0x1400-0x14ff]
[ 1.745491] pci 0000:00:0b.1: reg 14 32bit mmio: [0xf4002c00-0xf4002cff]
[ 1.745512] pci 0000:00:0b.1: reg 18 32bit mmio: [0xf4002800-0xf400287f]
[ 1.745606] pci 0000:00:0b.1: supports D2
[ 1.745614] pci 0000:00:0b.1: PME# supported from D2 D3hot D3cold
[ 1.745724] pci 0000:00:0b.1: PME# disabled
[ 1.745934] pci 0000:00:0d.0: reg 10 io port: [0x1800-0x18ff]
[ 1.745957] pci 0000:00:0d.0: reg 14 32bit mmio: [0xf4000000-0xf4001fff]
[ 1.746066] pci 0000:00:0d.0: supports D1 D2
[ 1.746074] pci 0000:00:0d.0: PME# supported from D1 D2 D3hot
[ 1.746186] pci 0000:00:0d.0: PME# disabled
[ 1.746472] pci 0000:01:00.0: reg 10 32bit mmio: [0xf5000000-0xf5ffffff]
[ 1.746494] pci 0000:01:00.0: reg 14 io port: [0x9000-0x90ff]
[ 1.746515] pci 0000:01:00.0: reg 18 32bit mmio: [0xf4100000-0xf4100fff]
[ 1.746569] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.746635] pci 0000:01:00.0: supports D1 D2
[ 1.746755] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff]
[ 1.746769] pci 0000:00:01.0: bridge 32bit mmio: [0xf4100000-0xf5ffffff]
[ 1.746970] device: '0000:00:00.0': device_add
[ 1.747010] bus: 'pci': add device 0000:00:00.0
[ 1.747178] PM: Adding info for pci:0000:00:00.0
[ 1.748720] device: '0000:00:01.0': device_add
[ 1.748782] bus: 'pci': add device 0000:00:01.0
[ 1.748921] PM: Adding info for pci:0000:00:01.0
[ 1.749620] device: '0000:00:07.0': device_add
[ 1.749659] bus: 'pci': add device 0000:00:07.0
[ 1.749823] PM: Adding info for pci:0000:00:07.0
[ 1.750388] device: '0000:00:07.1': device_add
[ 1.750451] bus: 'pci': add device 0000:00:07.1
[ 1.750585] PM: Adding info for pci:0000:00:07.1
[ 1.751175] device: '0000:00:07.2': device_add
[ 1.751213] bus: 'pci': add device 0000:00:07.2
[ 1.751349] PM: Adding info for pci:0000:00:07.2
[ 1.751903] device: '0000:00:07.3': device_add
[ 1.752098] bus: 'pci': add device 0000:00:07.3
[ 1.752236] PM: Adding info for pci:0000:00:07.3
[ 1.752833] device: '0000:00:0a.0': device_add
[ 1.752870] bus: 'pci': add device 0000:00:0a.0
[ 1.753006] PM: Adding info for pci:0000:00:0a.0
[ 1.753571] device: '0000:00:0a.1': device_add
[ 1.753609] bus: 'pci': add device 0000:00:0a.1
[ 1.753774] PM: Adding info for pci:0000:00:0a.1
[ 1.754342] device: '0000:00:0b.0': device_add
[ 1.754379] bus: 'pci': add device 0000:00:0b.0
[ 1.754515] PM: Adding info for pci:0000:00:0b.0
[ 1.755067] device: '0000:00:0b.1': device_add
[ 1.755104] bus: 'pci': add device 0000:00:0b.1
[ 1.755270] PM: Adding info for pci:0000:00:0b.1
[ 1.755831] device: '0000:00:0d.0': device_add
[ 1.755869] bus: 'pci': add device 0000:00:0d.0
[ 1.756818] PM: Adding info for pci:0000:00:0d.0
[ 1.757564] device: '0000:01:00.0': device_add
[ 1.757612] bus: 'pci': add device 0000:01:00.0
[ 1.757788] PM: Adding info for pci:0000:01:00.0
[ 1.758397] device: '0000:01': device_add
[ 1.758524] PM: Adding info for No Bus:0000:01
[ 1.759143] device: '0000:02': device_add
[ 1.759232] PM: Adding info for No Bus:0000:02
[ 1.759820] device: '0000:06': device_add
[ 1.759906] PM: Adding info for No Bus:0000:06
[ 1.760970] pci 0000:00:07.0: PIIX/ICH IRQ router [8086:7110]
[ 1.761309] PCI: setting IRQ 10 as level-triggered
[ 1.761319] pci 0000:00:0a.0: found PCI INT A -> IRQ 10
[ 1.761528] pci 0000:00:0a.0: sharing IRQ 10 with 0000:00:0b.0
[ 1.761646] pci 0000:00:0a.0: sharing IRQ 10 with 0000:00:0b.1
[ 1.761803] pci 0000:00:0a.1: found PCI INT B -> IRQ 10
[ 1.762046] pci 0000:00:0a.1: sharing IRQ 10 with 0000:01:00.0
[ 1.762661] device class 'net': registering
[ 1.763485] device: 'lo': device_add
[ 1.763896] PM: Adding info for No Bus:lo
[ 1.765731] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[ 1.765731] Bluetooth: Core ver 2.14
[ 1.765731] device class 'bluetooth': registering
[ 1.768576] NET: Registered protocol family 31
[ 1.768690] Bluetooth: HCI device and connection manager initialized
[ 1.768905] Bluetooth: HCI socket layer initialized
[ 1.769009] NET: Registered protocol family 8
[ 1.769108] NET: Registered protocol family 20
[ 1.769293] device class 'atm': registering
[ 1.771004] device class 'mem': registering
[ 1.771700] device: 'mem': device_add
[ 1.771787] PM: Adding info for No Bus:mem
[ 1.772731] device: 'kmem': device_add
[ 1.772812] PM: Adding info for No Bus:kmem
[ 1.773380] device: 'null': device_add
[ 1.773483] PM: Adding info for No Bus:null
[ 1.774047] device: 'port': device_add
[ 1.774122] PM: Adding info for No Bus:port
[ 1.774684] device: 'zero': device_add
[ 1.774760] PM: Adding info for No Bus:zero
[ 1.775369] device: 'full': device_add
[ 1.775445] PM: Adding info for No Bus:full
[ 1.776069] device: 'random': device_add
[ 1.776148] PM: Adding info for No Bus:random
[ 1.776717] device: 'urandom': device_add
[ 1.776797] PM: Adding info for No Bus:urandom
[ 1.777340] device: 'kmsg': device_add
[ 1.777446] PM: Adding info for No Bus:kmsg
[ 1.778016] device class 'firmware': registering
[ 1.779232] bus: 'pcmcia': registered
[ 1.780155] bus: 'ssb': registered
[ 1.780625] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 1.780753] pci 0000:00:01.0: IO window: 0x9000-0x9fff
[ 1.780865] pci 0000:00:01.0: MEM window: 0xf4100000-0xf5ffffff
[ 1.780979] pci 0000:00:01.0: PREFETCH window: 0x00000040000000-0x000000400fffff
[ 1.781147] pci 0000:00:0a.0: CardBus bridge, secondary bus 0000:02
[ 1.781252] pci 0000:00:0a.0: IO window: 0x002000-0x0020ff
[ 1.781362] pci 0000:00:0a.0: IO window: 0x002400-0x0024ff
[ 1.781473] pci 0000:00:0a.0: PREFETCH window: 0x30000000-0x33ffffff
[ 1.781586] pci 0000:00:0a.0: MEM window: 0x34000000-0x37ffffff
[ 1.781698] pci 0000:00:0a.1: CardBus bridge, secondary bus 0000:06
[ 1.781803] pci 0000:00:0a.1: IO window: 0x002800-0x0028ff
[ 1.781911] pci 0000:00:0a.1: IO window: 0x002c00-0x002cff
[ 1.782022] pci 0000:00:0a.1: PREFETCH window: 0x38000000-0x3bffffff
[ 1.782135] pci 0000:00:0a.1: MEM window: 0x3c000000-0x3fffffff
[ 1.782285] pci 0000:00:0a.0: found PCI INT A -> IRQ 10
[ 1.782533] pci 0000:00:0a.0: sharing IRQ 10 with 0000:00:0b.0
[ 1.782657] pci 0000:00:0a.0: sharing IRQ 10 with 0000:00:0b.1
[ 1.782814] pci 0000:00:0a.0: setting latency timer to 64
[ 1.782840] pci 0000:00:0a.1: found PCI INT B -> IRQ 10
[ 1.783126] pci 0000:00:0a.1: sharing IRQ 10 with 0000:01:00.0
[ 1.783250] pci 0000:00:0a.1: setting latency timer to 64
[ 1.783266] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 1.783275] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 1.783285] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
[ 1.783294] pci_bus 0000:01: resource 1 mem: [0xf4100000-0xf5ffffff]
[ 1.783303] pci_bus 0000:01: resource 2 mem: [0x40000000-0x400fffff]
[ 1.783311] pci_bus 0000:01: resource 3 mem: [0x0-0x0]
[ 1.783320] pci_bus 0000:02: resource 0 io: [0x2000-0x20ff]
[ 1.783329] pci_bus 0000:02: resource 1 io: [0x2400-0x24ff]
[ 1.783338] pci_bus 0000:02: resource 2 mem: [0x30000000-0x33ffffff]
[ 1.783347] pci_bus 0000:02: resource 3 mem: [0x34000000-0x37ffffff]
[ 1.783356] pci_bus 0000:06: resource 0 io: [0x2800-0x28ff]
[ 1.783365] pci_bus 0000:06: resource 1 io: [0x2c00-0x2cff]
[ 1.783374] pci_bus 0000:06: resource 2 mem: [0x38000000-0x3bffffff]
[ 1.783383] pci_bus 0000:06: resource 3 mem: [0x3c000000-0x3fffffff]
[ 1.783645] NET: Registered protocol family 2
[ 1.786368] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.789372] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.790380] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
[ 1.794068] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.794335] TCP reno registered
[ 1.795632] NET: Registered protocol family 1
[ 1.797439] checking if image is initramfs... it is
[ 2.328009] Freeing initrd memory: 2635k freed
[ 2.328263] Registering sysdev class 'i8259'
[ 2.329368] khelper used greatest stack depth: 3160 bytes left
[ 2.329654] Registering sys device of class 'i8259'
[ 2.329696] Registering sys device 'i82590'
[ 2.330356] Registering sysdev class 'i8237'
[ 2.330957] Registering sys device of class 'i8237'
[ 2.330987] Registering sys device 'i82370'
[ 2.331615] Registering platform device 'rtc_cmos'. Parent at platform
[ 2.331627] device: 'rtc_cmos': device_add
[ 2.331671] bus: 'platform': add device rtc_cmos
[ 2.331736] PM: Adding info for platform:rtc_cmos
[ 2.332428] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 2.332630] device class 'msr': registering
[ 2.333287] device: 'msr0': device_add
[ 2.333373] PM: Adding info for No Bus:msr0
[ 2.334093] device class 'cpuid': registering
[ 2.334741] device: 'cpu0': device_add
[ 2.334821] PM: Adding info for No Bus:cpu0
[ 2.335553] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 2.336020] device: 'apm_bios': device_add
[ 2.336214] PM: Adding info for No Bus:apm_bios
[ 2.337828] Registering sysdev class 'ioapic'
[ 2.338470] Registering platform device 'pcspkr'. Parent at platform
[ 2.338482] device: 'pcspkr': device_add
[ 2.338517] bus: 'platform': add device pcspkr
[ 2.338577] PM: Adding info for platform:pcspkr
[ 2.339168] scx200: NatSemi SCx200 Driver
[ 2.339286] bus: 'pci': add driver scx200
[ 2.340033] microcode: no support for this CPU vendor
[ 2.341190] Registering sysdev class 'timekeeping'
[ 2.341918] Registering sys device of class 'timekeeping'
[ 2.341948] Registering sys device 'timekeeping0'
[ 2.342498] Registering sysdev class 'clocksource'
[ 2.343192] Registering sys device of class 'clocksource'
[ 2.343225] Registering sys device 'clocksource0'
[ 2.343950] Registering sysdev class 'rttest'
[ 2.346727] Registering sys device of class 'rttest'
[ 2.346785] Registering sys device 'rttest0'
[ 2.347626] Registering sys device of class 'rttest'
[ 2.347656] Registering sys device 'rttest1'
[ 2.348571] Registering sys device of class 'rttest'
[ 2.348603] Registering sys device 'rttest2'
[ 2.349412] Registering sys device of class 'rttest'
[ 2.349440] Registering sys device 'rttest3'
[ 2.350361] Registering sys device of class 'rttest'
[ 2.350394] Registering sys device 'rttest4'
[ 2.351193] Registering sys device of class 'rttest'
[ 2.351225] Registering sys device 'rttest5'
[ 2.352410] Registering sys device of class 'rttest'
[ 2.352456] Registering sys device 'rttest6'
[ 2.353464] Registering sys device of class 'rttest'
[ 2.353499] Registering sys device 'rttest7'
[ 2.354110] Initializing RT-Tester: OK
[ 2.354301] device: 'snapshot': device_add
[ 2.354395] PM: Adding info for No Bus:snapshot
[ 2.452145] VFS: Disk quotas dquot_6.5.2
[ 2.453690] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.458167] device: 'dlm-control': device_add
[ 2.458269] PM: Adding info for No Bus:dlm-control
[ 2.458955] device: 'dlm-monitor': device_add
[ 2.459040] PM: Adding info for No Bus:dlm-monitor
[ 2.459721] device: 'dlm_plock': device_add
[ 2.459805] PM: Adding info for No Bus:dlm_plock
[ 2.460468] DLM (built Jan 10 2009 13:28:42) installed
[ 2.484899] NTFS driver 2.1.29 [Flags: R/W].
[ 2.491987] EFS: 1.0a - http://aeschi.ch.eu.org/efs/
[ 2.497034] QNX4 filesystem 0.2.3 registered.
[ 2.497182] device: 'autofs': device_add
[ 2.497296] PM: Adding info for No Bus:autofs
[ 2.497965] fuse init (API version 7.11)
[ 2.500248] device: 'fuse': device_add
[ 2.500341] PM: Adding info for No Bus:fuse
[ 2.502107] msgmni has been set to 970
[ 2.505624] cryptomgr_test used greatest stack depth: 2112 bytes left
[ 2.519533] alg: No test for stdrng (krng)
[ 2.520039] alg: No test for stdrng (ansi_cprng)
[ 2.521324] async_tx: api initialized (async)
[ 2.521651] io scheduler noop registered
[ 2.521753] io scheduler deadline registered
[ 2.524394] io scheduler cfq registered (default)
[ 2.533445] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 2.533644] pci 0000:00:07.2: uhci_check_and_reset_hc: legsup = 0x2000
[ 2.533653] pci 0000:00:07.2: Performing full reset
[ 2.533776] pci 0000:01:00.0: Boot video device
[ 2.535261] bus: 'pci_express': registered
[ 2.535279] bus: 'pci': add driver pcieport-driver
[ 2.535322] bus: 'pci': driver_probe_device: matched device 0000:00:01.0 with driver pcieport-driver
[ 2.535334] bus: 'pci': really_probe: probing driver pcieport-driver with device 0000:00:01.0
[ 2.536342] bus: 'pci_express': add driver aer
[ 2.536967] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.537088] bus: 'pci': add driver shpchp
[ 2.537129] bus: 'pci': driver_probe_device: matched device 0000:00:01.0 with driver shpchp
[ 2.537139] bus: 'pci': really_probe: probing driver shpchp with device 0000:00:01.0
[ 2.537888] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.538003] fakephp: Fake PCI Hot Plug Controller Driver
[ 2.543763] bus: 'spi': add driver ltv350qv
[ 2.544444] bus: 'platform': add driver platform-lcd
[ 2.545068] bus: 'platform': add driver generic-bl
[ 2.545722] bus: 'platform': add driver progear-bl
[ 2.546394] Registering platform device 'progear-bl'. Parent at platform
[ 2.546405] device: 'progear-bl': device_add
[ 2.546448] bus: 'platform': add device progear-bl
[ 2.546514] PM: Adding info for platform:progear-bl
[ 2.547122] bus: 'platform': driver_probe_device: matched device progear-bl with driver progear-bl
[ 2.547135] bus: 'platform': really_probe: probing driver progear-bl with device progear-bl
[ 2.547198] ALI M7101 PMU not found.
[ 2.547368] bus: 'platform': add driver cr_backlight
[ 2.548027] Registering platform device 'cr_backlight'. Parent at platform
[ 2.548039] device: 'cr_backlight': device_add
[ 2.548386] bus: 'platform': add device cr_backlight
[ 2.548480] PM: Adding info for platform:cr_backlight
[ 2.549135] bus: 'platform': driver_probe_device: matched device cr_backlight with driver cr_backlight
[ 2.549149] bus: 'platform': really_probe: probing driver cr_backlight with device cr_backlight
[ 2.549214] INTEL CARILLO RANCH LPC not found.
[ 2.549376] Carillo Ranch Backlight Driver Initialized.
[ 2.549498] bus: 'pci': add driver CyberPro
[ 2.550191] bus: 'pci': add driver pm2fb
[ 2.550862] bus: 'pci': add driver pm3fb
[ 2.551507] bus: 'pci': add driver matroxfb
[ 2.552215] bus: 'pci': add driver rivafb
[ 2.552892] bus: 'pci': add driver atyfb
[ 2.553619] bus: 'pci': add driver aty128fb
[ 2.554449] bus: 'pci': add driver sisfb
[ 2.555107] bus: 'pci': add driver savagefb
[ 2.555796] bus: 'pci': add driver neofb
[ 2.557488] bus: 'pci': add driver tdfxfb
[ 2.558208] bus: 'pci': add driver imsttfb
[ 2.558869] vmlfb: initializing
[ 2.558884] bus: 'pci': add driver vmlfb
[ 2.559580] Could not find Carillo Ranch MCH device.
[ 2.559711] bus: 'pci': add driver s3fb
[ 2.560482] bus: 'platform': add driver hecubafb
[ 2.561119] bus: 'platform': add driver hgafb
[ 2.561782] Registering platform device 'hgafb.0'. Parent at platform
[ 2.561793] device: 'hgafb.0': device_add
[ 2.561833] bus: 'platform': add device hgafb.0
[ 2.561899] PM: Adding info for platform:hgafb.0
[ 2.562483] bus: 'platform': driver_probe_device: matched device hgafb.0 with driver hgafb
[ 2.562495] bus: 'platform': really_probe: probing driver hgafb with device hgafb.0
[ 2.562587] hgafb: HGA card not detected.
[ 2.562755] hgafb: probe of hgafb.0 failed with error -22
[ 2.562883] bus: 'pci': add driver sstfb
[ 2.563590] bus: 'platform': add driver tmio-fb
[ 2.565244] bus: 'platform': add driver metronomefb
[ 2.566052] bus: 'pci': add driver carminefb
[ 2.566722] bus: 'platform': add driver uvesafb
[ 2.567360] Registering platform device 'uvesafb.0'. Parent at platform
[ 2.567372] device: 'uvesafb.0': device_add
[ 2.567411] bus: 'platform': add device uvesafb.0
[ 2.567476] PM: Adding info for platform:uvesafb.0
[ 2.568168] bus: 'platform': driver_probe_device: matched device uvesafb.0 with driver uvesafb
[ 2.568181] bus: 'platform': really_probe: probing driver uvesafb with device uvesafb.0
[ 2.569231] uvesafb: failed to execute /sbin/v86d
[ 2.569351] uvesafb: make sure that the v86d helper is installed and executable
[ 2.569533] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)
[ 2.569649] uvesafb: vbe_init() failed with -22
[ 2.569849] uvesafb: probe of uvesafb.0 failed with error -22
[ 2.569992] bus: 'platform': add driver reg-virt-consumer
[ 2.570709] bus: 'platform': add driver wm8400-regulator
[ 2.571515] device: 'tty': device_add
[ 2.571608] PM: Adding info for No Bus:tty
[ 2.573356] device: 'console': device_add
[ 2.573494] PM: Adding info for No Bus:console
[ 2.574262] device: 'tty0': device_add
[ 2.574345] PM: Adding info for No Bus:tty0
[ 2.574960] device class 'vc': registering
[ 2.575587] device: 'vcs': device_add
[ 2.575669] PM: Adding info for No Bus:vcs
[ 2.576422] device: 'vcsa': device_add
[ 2.576504] PM: Adding info for No Bus:vcsa
[ 2.577253] device: 'tty1': device_add
[ 2.577342] PM: Adding info for No Bus:tty1
[ 2.577966] device: 'tty2': device_add
[ 2.578045] PM: Adding info for No Bus:tty2
[ 2.578626] device: 'tty3': device_add
[ 2.578732] PM: Adding info for No Bus:tty3
[ 2.579326] device: 'tty4': device_add
[ 2.579402] PM: Adding info for No Bus:tty4
[ 2.581103] device: 'tty5': device_add
[ 2.581230] PM: Adding info for No Bus:tty5
[ 2.582102] device: 'tty6': device_add
[ 2.582226] PM: Adding info for No Bus:tty6
[ 2.582831] device: 'tty7': device_add
[ 2.582910] PM: Adding info for No Bus:tty7
[ 2.583488] device: 'tty8': device_add
[ 2.583570] PM: Adding info for No Bus:tty8
[ 2.584938] device: 'tty9': device_add
[ 2.585053] PM: Adding info for No Bus:tty9
[ 2.585785] device: 'tty10': device_add
[ 2.585900] PM: Adding info for No Bus:tty10
[ 2.586531] device: 'tty11': device_add
[ 2.586612] PM: Adding info for No Bus:tty11
[ 2.587210] device: 'tty12': device_add
[ 2.587290] PM: Adding info for No Bus:tty12
[ 2.587875] device: 'tty13': device_add
[ 2.587957] PM: Adding info for No Bus:tty13
[ 2.588648] device: 'tty14': device_add
[ 2.588733] PM: Adding info for No Bus:tty14
[ 2.589381] device: 'tty15': device_add
[ 2.589470] PM: Adding info for No Bus:tty15
[ 2.590071] device: 'tty16': device_add
[ 2.590185] PM: Adding info for No Bus:tty16
[ 2.590784] device: 'tty17': device_add
[ 2.590868] PM: Adding info for No Bus:tty17
[ 2.591491] device: 'tty18': device_add
[ 2.591577] PM: Adding info for No Bus:tty18
[ 2.592827] device: 'tty19': device_add
[ 2.592940] PM: Adding info for No Bus:tty19
[ 2.593650] device: 'tty20': device_add
[ 2.593740] PM: Adding info for No Bus:tty20
[ 2.594346] device: 'tty21': device_add
[ 2.594433] PM: Adding info for No Bus:tty21
[ 2.595009] device: 'tty22': device_add
[ 2.595096] PM: Adding info for No Bus:tty22
[ 2.595675] device: 'tty23': device_add
[ 2.595792] PM: Adding info for No Bus:tty23
[ 2.596462] device: 'tty24': device_add
[ 2.596589] PM: Adding info for No Bus:tty24
[ 2.597189] device: 'tty25': device_add
[ 2.597280] PM: Adding info for No Bus:tty25
[ 2.597887] device: 'tty26': device_add
[ 2.597975] PM: Adding info for No Bus:tty26
[ 2.598580] device: 'tty27': device_add
[ 2.598701] PM: Adding info for No Bus:tty27
[ 2.599356] device: 'tty28': device_add
[ 2.599451] PM: Adding info for No Bus:tty28
[ 2.601069] device: 'tty29': device_add
[ 2.601245] PM: Adding info for No Bus:tty29
[ 2.602005] device: 'tty30': device_add
[ 2.602108] PM: Adding info for No Bus:tty30
[ 2.602716] device: 'tty31': device_add
[ 2.602806] PM: Adding info for No Bus:tty31
[ 2.603386] device: 'tty32': device_add
[ 2.603476] PM: Adding info for No Bus:tty32
[ 2.604063] device: 'tty33': device_add
[ 2.604225] PM: Adding info for No Bus:tty33
[ 2.604831] device: 'tty34': device_add
[ 2.604928] PM: Adding info for No Bus:tty34
[ 2.605506] device: 'tty35': device_add
[ 2.605599] PM: Adding info for No Bus:tty35
[ 2.606193] device: 'tty36': device_add
[ 2.606317] PM: Adding info for No Bus:tty36
[ 2.607015] device: 'tty37': device_add
[ 2.607127] PM: Adding info for No Bus:tty37
[ 2.607716] device: 'tty38': device_add
[ 2.607811] PM: Adding info for No Bus:tty38
[ 2.609360] device: 'tty39': device_add
[ 2.609497] PM: Adding info for No Bus:tty39
[ 2.610173] device: 'tty40': device_add
[ 2.610271] PM: Adding info for No Bus:tty40
[ 2.610853] device: 'tty41': device_add
[ 2.610949] PM: Adding info for No Bus:tty41
[ 2.611525] device: 'tty42': device_add
[ 2.611651] PM: Adding info for No Bus:tty42
[ 2.612419] device: 'tty43': device_add
[ 2.612562] PM: Adding info for No Bus:tty43
[ 2.613204] device: 'tty44': device_add
[ 2.613296] PM: Adding info for No Bus:tty44
[ 2.613899] device: 'tty45': device_add
[ 2.613995] PM: Adding info for No Bus:tty45
[ 2.614613] device: 'tty46': device_add
[ 2.614795] PM: Adding info for No Bus:tty46
[ 2.615397] device: 'tty47': device_add
[ 2.615524] PM: Adding info for No Bus:tty47
[ 2.617052] device: 'tty48': device_add
[ 2.617197] PM: Adding info for No Bus:tty48
[ 2.618013] device: 'tty49': device_add
[ 2.618157] PM: Adding info for No Bus:tty49
[ 2.618794] device: 'tty50': device_add
[ 2.618891] PM: Adding info for No Bus:tty50
[ 2.619500] device: 'tty51': device_add
[ 2.619593] PM: Adding info for No Bus:tty51
[ 2.621147] device: 'tty52': device_add
[ 2.621307] PM: Adding info for No Bus:tty52
[ 2.622039] device: 'tty53': device_add
[ 2.622146] PM: Adding info for No Bus:tty53
[ 2.622761] device: 'tty54': device_add
[ 2.622858] PM: Adding info for No Bus:tty54
[ 2.623464] device: 'tty55': device_add
[ 2.623562] PM: Adding info for No Bus:tty55
[ 2.624245] device: 'tty56': device_add
[ 2.624381] PM: Adding info for No Bus:tty56
[ 2.625067] device: 'tty57': device_add
[ 2.625172] PM: Adding info for No Bus:tty57
[ 2.625776] device: 'tty58': device_add
[ 2.625876] PM: Adding info for No Bus:tty58
[ 2.626474] device: 'tty59': device_add
[ 2.626577] PM: Adding info for No Bus:tty59
[ 2.627164] device: 'tty60': device_add
[ 2.627266] PM: Adding info for No Bus:tty60
[ 2.627889] device: 'tty61': device_add
[ 2.628030] PM: Adding info for No Bus:tty61
[ 2.629689] device: 'tty62': device_add
[ 2.629857] PM: Adding info for No Bus:tty62
[ 2.630490] device: 'tty63': device_add
[ 2.630595] PM: Adding info for No Bus:tty63
[ 2.631686] device: 'ptyp0': device_add
[ 2.631813] PM: Adding info for No Bus:ptyp0
[ 2.632589] device: 'ptyp1': device_add
[ 2.632698] PM: Adding info for No Bus:ptyp1
[ 2.633311] device: 'ptyp2': device_add
[ 2.633409] PM: Adding info for No Bus:ptyp2
[ 2.634055] device: 'ptyp3': device_add
[ 2.634158] PM: Adding info for No Bus:ptyp3
[ 2.634755] device: 'ptyp4': device_add
[ 2.634858] PM: Adding info for No Bus:ptyp4
[ 2.635448] device: 'ptyp5': device_add
[ 2.635577] PM: Adding info for No Bus:ptyp5
[ 2.636899] device: 'ptyp6': device_add
[ 2.637048] PM: Adding info for No Bus:ptyp6
[ 2.637740] device: 'ptyp7': device_add
[ 2.637848] PM: Adding info for No Bus:ptyp7
[ 2.638425] device: 'ptyp8': device_add
[ 2.638527] PM: Adding info for No Bus:ptyp8
[ 2.639127] device: 'ptyp9': device_add
[ 2.639230] PM: Adding info for No Bus:ptyp9
[ 2.639809] device: 'ptypa': device_add
[ 2.639915] PM: Adding info for No Bus:ptypa
[ 2.640572] device: 'ptypb': device_add
[ 2.640716] PM: Adding info for No Bus:ptypb
[ 2.641318] device: 'ptypc': device_add
[ 2.641420] PM: Adding info for No Bus:ptypc
[ 2.642027] device: 'ptypd': device_add
[ 2.642137] PM: Adding info for No Bus:ptypd
[ 2.642783] device: 'ptype': device_add
[ 2.642900] PM: Adding info for No Bus:ptype
[ 2.643671] device: 'ptypf': device_add
[ 2.643842] PM: Adding info for No Bus:ptypf
[ 2.645446] device: 'ptyq0': device_add
[ 2.645610] PM: Adding info for No Bus:ptyq0
[ 2.646330] device: 'ptyq1': device_add
[ 2.646452] PM: Adding info for No Bus:ptyq1
[ 2.647057] device: 'ptyq2': device_add
[ 2.647200] PM: Adding info for No Bus:ptyq2
[ 2.647799] device: 'ptyq3': device_add
[ 2.647908] PM: Adding info for No Bus:ptyq3
[ 2.648604] device: 'ptyq4': device_add
[ 2.648723] PM: Adding info for No Bus:ptyq4
[ 2.649343] device: 'ptyq5': device_add
[ 2.649452] PM: Adding info for No Bus:ptyq5
[ 2.650063] device: 'ptyq6': device_add
[ 2.650172] PM: Adding info for No Bus:ptyq6
[ 2.650782] device: 'ptyq7': device_add
[ 2.650891] PM: Adding info for No Bus:ptyq7
[ 2.651491] device: 'ptyq8': device_add
[ 2.651634] PM: Adding info for No Bus:ptyq8
[ 2.653484] device: 'ptyq9': device_add
[ 2.653673] PM: Adding info for No Bus:ptyq9
[ 2.654434] device: 'ptyqa': device_add
[ 2.654558] PM: Adding info for No Bus:ptyqa
[ 2.655170] device: 'ptyqb': device_add
[ 2.655322] PM: Adding info for No Bus:ptyqb
[ 2.655955] device: 'ptyqc': device_add
[ 2.656074] PM: Adding info for No Bus:ptyqc
[ 2.657655] device: 'ptyqd': device_add
[ 2.657828] PM: Adding info for No Bus:ptyqd
[ 2.658448] device: 'ptyqe': device_add
[ 2.658569] PM: Adding info for No Bus:ptyqe
[ 2.659233] device: 'ptyqf': device_add
[ 2.659385] PM: Adding info for No Bus:ptyqf
[ 2.660002] device: 'ptyr0': device_add
[ 2.660195] PM: Adding info for No Bus:ptyr0
[ 2.660835] device: 'ptyr1': device_add
[ 2.660986] PM: Adding info for No Bus:ptyr1
[ 2.661598] device: 'ptyr2': device_add
[ 2.661721] PM: Adding info for No Bus:ptyr2
[ 2.662333] device: 'ptyr3': device_add
[ 2.662450] PM: Adding info for No Bus:ptyr3
[ 2.663056] device: 'ptyr4': device_add
[ 2.663174] PM: Adding info for No Bus:ptyr4
[ 2.663790] device: 'ptyr5': device_add
[ 2.663912] PM: Adding info for No Bus:ptyr5
[ 2.665257] device: 'ptyr6': device_add
[ 2.665452] PM: Adding info for No Bus:ptyr6
[ 2.666102] device: 'ptyr7': device_add
[ 2.666225] PM: Adding info for No Bus:ptyr7
[ 2.666837] device: 'ptyr8': device_add
[ 2.666956] PM: Adding info for No Bus:ptyr8
[ 2.667572] device: 'ptyr9': device_add
[ 2.667693] PM: Adding info for No Bus:ptyr9
[ 2.668376] device: 'ptyra': device_add
[ 2.668503] PM: Adding info for No Bus:ptyra
[ 2.669127] device: 'ptyrb': device_add
[ 2.669246] PM: Adding info for No Bus:ptyrb
[ 2.669891] device: 'ptyrc': device_add
[ 2.670045] PM: Adding info for No Bus:ptyrc
[ 2.670740] device: 'ptyrd': device_add
[ 2.670871] PM: Adding info for No Bus:ptyrd
[ 2.671506] device: 'ptyre': device_add
[ 2.671633] PM: Adding info for No Bus:ptyre
[ 2.673088] device: 'ptyrf': device_add
[ 2.673280] PM: Adding info for No Bus:ptyrf
[ 2.673973] device: 'ptys0': device_add
[ 2.674102] PM: Adding info for No Bus:ptys0
[ 2.674714] device: 'ptys1': device_add
[ 2.674839] PM: Adding info for No Bus:ptys1
[ 2.675447] device: 'ptys2': device_add
[ 2.675579] PM: Adding info for No Bus:ptys2
[ 2.676236] device: 'ptys3': device_add
[ 2.676407] PM: Adding info for No Bus:ptys3
[ 2.677038] device: 'ptys4': device_add
[ 2.677202] PM: Adding info for No Bus:ptys4
[ 2.677807] device: 'ptys5': device_add
[ 2.677936] PM: Adding info for No Bus:ptys5
[ 2.678530] device: 'ptys6': device_add
[ 2.678654] PM: Adding info for No Bus:ptys6
[ 2.679313] device: 'ptys7': device_add
[ 2.679448] PM: Adding info for No Bus:ptys7
[ 2.681082] device: 'ptys8': device_add
[ 2.681318] PM: Adding info for No Bus:ptys8
[ 2.682076] device: 'ptys9': device_add
[ 2.682256] PM: Adding info for No Bus:ptys9
[ 2.682877] device: 'ptysa': device_add
[ 2.683015] PM: Adding info for No Bus:ptysa
[ 2.683680] device: 'ptysb': device_add
[ 2.683827] PM: Adding info for No Bus:ptysb
[ 2.684521] device: 'ptysc': device_add
[ 2.684665] PM: Adding info for No Bus:ptysc
[ 2.685282] device: 'ptysd': device_add
[ 2.685414] PM: Adding info for No Bus:ptysd
[ 2.686037] device: 'ptyse': device_add
[ 2.686171] PM: Adding info for No Bus:ptyse
[ 2.686770] device: 'ptysf': device_add
[ 2.686907] PM: Adding info for No Bus:ptysf
[ 2.687512] device: 'ptyt0': device_add
[ 2.687679] PM: Adding info for No Bus:ptyt0
[ 2.689550] device: 'ptyt1': device_add
[ 2.689773] PM: Adding info for No Bus:ptyt1
[ 2.690495] device: 'ptyt2': device_add
[ 2.690634] PM: Adding info for No Bus:ptyt2
[ 2.691250] device: 'ptyt3': device_add
[ 2.691382] PM: Adding info for No Bus:ptyt3
[ 2.691996] device: 'ptyt4': device_add
[ 2.692194] PM: Adding info for No Bus:ptyt4
[ 2.692829] device: 'ptyt5': device_add
[ 2.692966] PM: Adding info for No Bus:ptyt5
[ 2.693577] device: 'ptyt6': device_add
[ 2.693774] PM: Adding info for No Bus:ptyt6
[ 2.694413] device: 'ptyt7': device_add
[ 2.694551] PM: Adding info for No Bus:ptyt7
[ 2.695152] device: 'ptyt8': device_add
[ 2.695284] PM: Adding info for No Bus:ptyt8
[ 2.695959] device: 'ptyt9': device_add
[ 2.696874] PM: Adding info for No Bus:ptyt9
[ 2.697639] device: 'ptyta': device_add
[ 2.697837] PM: Adding info for No Bus:ptyta
[ 2.698456] device: 'ptytb': device_add
[ 2.698598] PM: Adding info for No Bus:ptytb
[ 2.699195] device: 'ptytc': device_add
[ 2.699338] PM: Adding info for No Bus:ptytc
[ 2.699943] device: 'ptytd': device_add
[ 2.700191] PM: Adding info for No Bus:ptytd
[ 2.700842] device: 'ptyte': device_add
[ 2.700985] PM: Adding info for No Bus:ptyte
[ 2.701608] device: 'ptytf': device_add
[ 2.701751] PM: Adding info for No Bus:ptytf
[ 2.702365] device: 'ptyu0': device_add
[ 2.702508] PM: Adding info for No Bus:ptyu0
[ 2.703117] device: 'ptyu1': device_add
[ 2.703254] PM: Adding info for No Bus:ptyu1
[ 2.703867] device: 'ptyu2': device_add
[ 2.704010] PM: Adding info for No Bus:ptyu2
[ 2.705610] device: 'ptyu3': device_add
[ 2.705839] PM: Adding info for No Bus:ptyu3
[ 2.706466] device: 'ptyu4': device_add
[ 2.706649] PM: Adding info for No Bus:ptyu4
[ 2.707253] device: 'ptyu5': device_add
[ 2.707398] PM: Adding info for No Bus:ptyu5
[ 2.708007] device: 'ptyu6': device_add
[ 2.708225] PM: Adding info for No Bus:ptyu6
[ 2.708894] device: 'ptyu7': device_add
[ 2.709055] PM: Adding info for No Bus:ptyu7
[ 2.709688] device: 'ptyu8': device_add
[ 2.709869] PM: Adding info for No Bus:ptyu8
[ 2.710489] device: 'ptyu9': device_add
[ 2.710639] PM: Adding info for No Bus:ptyu9
[ 2.711245] device: 'ptyua': device_add
[ 2.711424] PM: Adding info for No Bus:ptyua
[ 2.712929] device: 'ptyub': device_add
[ 2.713198] PM: Adding info for No Bus:ptyub
[ 2.713989] device: 'ptyuc': device_add
[ 2.714159] PM: Adding info for No Bus:ptyuc
[ 2.714782] device: 'ptyud': device_add
[ 2.714929] PM: Adding info for No Bus:ptyud
[ 2.715540] device: 'ptyue': device_add
[ 2.715686] PM: Adding info for No Bus:ptyue
[ 2.716376] device: 'ptyuf': device_add
[ 2.716534] PM: Adding info for No Bus:ptyuf
[ 2.717167] device: 'ptyv0': device_add
[ 2.717319] PM: Adding info for No Bus:ptyv0
[ 2.717942] device: 'ptyv1': device_add
[ 2.718126] PM: Adding info for No Bus:ptyv1
[ 2.718755] device: 'ptyv2': device_add
[ 2.718905] PM: Adding info for No Bus:ptyv2
[ 2.719515] device: 'ptyv3': device_add
[ 2.719661] PM: Adding info for No Bus:ptyv3
[ 2.721324] device: 'ptyv4': device_add
[ 2.721564] PM: Adding info for No Bus:ptyv4
[ 2.722329] device: 'ptyv5': device_add
[ 2.722498] PM: Adding info for No Bus:ptyv5
[ 2.723126] device: 'ptyv6': device_add
[ 2.723276] PM: Adding info for No Bus:ptyv6
[ 2.723993] device: 'ptyv7': device_add
[ 2.724305] PM: Adding info for No Bus:ptyv7
[ 2.724959] device: 'ptyv8': device_add
[ 2.725121] PM: Adding info for No Bus:ptyv8
[ 2.725738] device: 'ptyv9': device_add
[ 2.725893] PM: Adding info for No Bus:ptyv9
[ 2.726491] device: 'ptyva': device_add
[ 2.726677] PM: Adding info for No Bus:ptyva
[ 2.727289] device: 'ptyvb': device_add
[ 2.727445] PM: Adding info for No Bus:ptyvb
[ 2.728043] device: 'ptyvc': device_add
[ 2.729037] PM: Adding info for No Bus:ptyvc
[ 2.729846] device: 'ptyvd': device_add
[ 2.730032] PM: Adding info for No Bus:ptyvd
[ 2.730661] device: 'ptyve': device_add
[ 2.730853] PM: Adding info for No Bus:ptyve
[ 2.731462] device: 'ptyvf': device_add
[ 2.731620] PM: Adding info for No Bus:ptyvf
[ 2.732303] device: 'ptyw0': device_add
[ 2.732473] PM: Adding info for No Bus:ptyw0
[ 2.733111] device: 'ptyw1': device_add
[ 2.733267] PM: Adding info for No Bus:ptyw1
[ 2.733885] device: 'ptyw2': device_add
[ 2.734041] PM: Adding info for No Bus:ptyw2
[ 2.734711] device: 'ptyw3': device_add
[ 2.734889] PM: Adding info for No Bus:ptyw3
[ 2.735514] device: 'ptyw4': device_add
[ 2.735704] PM: Adding info for No Bus:ptyw4
[ 2.737270] device: 'ptyw5': device_add
[ 2.737518] PM: Adding info for No Bus:ptyw5
[ 2.738214] device: 'ptyw6': device_add
[ 2.738380] PM: Adding info for No Bus:ptyw6
[ 2.739012] device: 'ptyw7': device_add
[ 2.739183] PM: Adding info for No Bus:ptyw7
[ 2.739799] device: 'ptyw8': device_add
[ 2.739959] PM: Adding info for No Bus:ptyw8
[ 2.740671] device: 'ptyw9': device_add
[ 2.740846] PM: Adding info for No Bus:ptyw9
[ 2.741469] device: 'ptywa': device_add
[ 2.741628] PM: Adding info for No Bus:ptywa
[ 2.742246] device: 'ptywb': device_add
[ 2.742507] PM: Adding info for No Bus:ptywb
[ 2.743148] device: 'ptywc': device_add
[ 2.743350] PM: Adding info for No Bus:ptywc
[ 2.743994] device: 'ptywd': device_add
[ 2.745305] PM: Adding info for No Bus:ptywd
[ 2.746097] device: 'ptywe': device_add
[ 2.746291] PM: Adding info for No Bus:ptywe
[ 2.746906] device: 'ptywf': device_add
[ 2.747071] PM: Adding info for No Bus:ptywf
[ 2.747768] device: 'ptyx0': device_add
[ 2.747964] PM: Adding info for No Bus:ptyx0
[ 2.748710] device: 'ptyx1': device_add
[ 2.748897] PM: Adding info for No Bus:ptyx1
[ 2.749517] device: 'ptyx2': device_add
[ 2.749720] PM: Adding info for No Bus:ptyx2
[ 2.750348] device: 'ptyx3': device_add
[ 2.750515] PM: Adding info for No Bus:ptyx3
[ 2.751113] device: 'ptyx4': device_add
[ 2.751277] PM: Adding info for No Bus:ptyx4
[ 2.751895] device: 'ptyx5': device_add
[ 2.752052] PM: Adding info for No Bus:ptyx5
[ 2.753701] device: 'ptyx6': device_add
[ 2.753949] PM: Adding info for No Bus:ptyx6
[ 2.754599] device: 'ptyx7': device_add
[ 2.754775] PM: Adding info for No Bus:ptyx7
[ 2.755402] device: 'ptyx8': device_add
[ 2.755598] PM: Adding info for No Bus:ptyx8
[ 2.756298] device: 'ptyx9': device_add
[ 2.756491] PM: Adding info for No Bus:ptyx9
[ 2.757126] device: 'ptyxa': device_add
[ 2.757294] PM: Adding info for No Bus:ptyxa
[ 2.757949] device: 'ptyxb': device_add
[ 2.758121] PM: Adding info for No Bus:ptyxb
[ 2.758761] device: 'ptyxc': device_add
[ 2.758931] PM: Adding info for No Bus:ptyxc
[ 2.759556] device: 'ptyxd': device_add
[ 2.759721] PM: Adding info for No Bus:ptyxd
[ 2.761186] device: 'ptyxe': device_add
[ 2.761442] PM: Adding info for No Bus:ptyxe
[ 2.762187] device: 'ptyxf': device_add
[ 2.762444] PM: Adding info for No Bus:ptyxf
[ 2.763096] device: 'ptyy0': device_add
[ 2.763274] PM: Adding info for No Bus:ptyy0
[ 2.763894] device: 'ptyy1': device_add
[ 2.764065] PM: Adding info for No Bus:ptyy1
[ 2.764793] device: 'ptyy2': device_add
[ 2.764976] PM: Adding info for No Bus:ptyy2
[ 2.765613] device: 'ptyy3': device_add
[ 2.765782] PM: Adding info for No Bus:ptyy3
[ 2.766400] device: 'ptyy4': device_add
[ 2.766567] PM: Adding info for No Bus:ptyy4
[ 2.767179] device: 'ptyy5': device_add
[ 2.767385] PM: Adding info for No Bus:ptyy5
[ 2.768021] device: 'ptyy6': device_add
[ 2.769206] PM: Adding info for No Bus:ptyy6
[ 2.769987] device: 'ptyy7': device_add
[ 2.770205] PM: Adding info for No Bus:ptyy7
[ 2.770844] device: 'ptyy8': device_add
[ 2.771029] PM: Adding info for No Bus:ptyy8
[ 2.771741] device: 'ptyy9': device_add
[ 2.771954] PM: Adding info for No Bus:ptyy9
[ 2.772667] device: 'ptyya': device_add
[ 2.772855] PM: Adding info for No Bus:ptyya
[ 2.773499] device: 'ptyyb': device_add
[ 2.773720] PM: Adding info for No Bus:ptyyb
[ 2.774355] device: 'ptyyc': device_add
[ 2.774579] PM: Adding info for No Bus:ptyyc
[ 2.775260] device: 'ptyyd': device_add
[ 2.775449] PM: Adding info for No Bus:ptyyd
[ 2.776068] device: 'ptyye': device_add
[ 2.777173] PM: Adding info for No Bus:ptyye
[ 2.777986] device: 'ptyyf': device_add
[ 2.778188] PM: Adding info for No Bus:ptyyf
[ 2.778814] device: 'ptyz0': device_add
[ 2.778993] PM: Adding info for No Bus:ptyz0
[ 2.779630] device: 'ptyz1': device_add
[ 2.779845] PM: Adding info for No Bus:ptyz1
[ 2.780578] device: 'ptyz2': device_add
[ 2.780802] PM: Adding info for No Bus:ptyz2
[ 2.781452] device: 'ptyz3': device_add
[ 2.781639] PM: Adding info for No Bus:ptyz3
[ 2.782290] device: 'ptyz4': device_add
[ 2.782475] PM: Adding info for No Bus:ptyz4
[ 2.783121] device: 'ptyz5': device_add
[ 2.783311] PM: Adding info for No Bus:ptyz5
[ 2.783982] device: 'ptyz6': device_add
[ 2.784969] PM: Adding info for No Bus:ptyz6
[ 2.785736] device: 'ptyz7': device_add
[ 2.785981] PM: Adding info for No Bus:ptyz7
[ 2.786633] device: 'ptyz8': device_add
[ 2.786823] PM: Adding info for No Bus:ptyz8
[ 2.787467] device: 'ptyz9': device_add
[ 2.787691] PM: Adding info for No Bus:ptyz9
[ 2.788413] device: 'ptyza': device_add
[ 2.788618] PM: Adding info for No Bus:ptyza
[ 2.789329] device: 'ptyzb': device_add
[ 2.789520] PM: Adding info for No Bus:ptyzb
[ 2.790167] device: 'ptyzc': device_add
[ 2.790350] PM: Adding info for No Bus:ptyzc
[ 2.790989] device: 'ptyzd': device_add
[ 2.791176] PM: Adding info for No Bus:ptyzd
[ 2.791793] device: 'ptyze': device_add
[ 2.791985] PM: Adding info for No Bus:ptyze
[ 2.793681] device: 'ptyzf': device_add
[ 2.793983] PM: Adding info for No Bus:ptyzf
[ 2.794650] device: 'ptya0': device_add
[ 2.794882] PM: Adding info for No Bus:ptya0
[ 2.795522] device: 'ptya1': device_add
[ 2.795712] PM: Adding info for No Bus:ptya1
[ 2.796513] device: 'ptya2': device_add
[ 2.796754] PM: Adding info for No Bus:ptya2
[ 2.797387] device: 'ptya3': device_add
[ 2.797615] PM: Adding info for No Bus:ptya3
[ 2.798280] device: 'ptya4': device_add
[ 2.798483] PM: Adding info for No Bus:ptya4
[ 2.799120] device: 'ptya5': device_add
[ 2.799316] PM: Adding info for No Bus:ptya5
[ 2.799936] device: 'ptya6': device_add
[ 2.800934] PM: Adding info for No Bus:ptya6
[ 2.801735] device: 'ptya7': device_add
[ 2.802006] PM: Adding info for No Bus:ptya7
[ 2.802675] device: 'ptya8': device_add
[ 2.802868] PM: Adding info for No Bus:ptya8
[ 2.803572] device: 'ptya9': device_add
[ 2.803785] PM: Adding info for No Bus:ptya9
[ 2.804505] device: 'ptyaa': device_add
[ 2.804716] PM: Adding info for No Bus:ptyaa
[ 2.805355] device: 'ptyab': device_add
[ 2.805546] PM: Adding info for No Bus:ptyab
[ 2.806179] device: 'ptyac': device_add
[ 2.806381] PM: Adding info for No Bus:ptyac
[ 2.807017] device: 'ptyad': device_add
[ 2.807250] PM: Adding info for No Bus:ptyad
[ 2.807894] device: 'ptyae': device_add
[ 2.808094] PM: Adding info for No Bus:ptyae
[ 2.809589] device: 'ptyaf': device_add
[ 2.809887] PM: Adding info for No Bus:ptyaf
[ 2.810549] device: 'ptyb0': device_add
[ 2.810749] PM: Adding info for No Bus:ptyb0
[ 2.811370] device: 'ptyb1': device_add
[ 2.811569] PM: Adding info for No Bus:ptyb1
[ 2.812263] device: 'ptyb2': device_add
[ 2.812477] PM: Adding info for No Bus:ptyb2
[ 2.813119] device: 'ptyb3': device_add
[ 2.813357] PM: Adding info for No Bus:ptyb3
[ 2.813997] device: 'ptyb4': device_add
[ 2.814202] PM: Adding info for No Bus:ptyb4
[ 2.814853] device: 'ptyb5': device_add
[ 2.815056] PM: Adding info for No Bus:ptyb5
[ 2.815706] device: 'ptyb6': device_add
[ 2.815947] PM: Adding info for No Bus:ptyb6
[ 2.817640] device: 'ptyb7': device_add
[ 2.817985] PM: Adding info for No Bus:ptyb7
[ 2.818670] device: 'ptyb8': device_add
[ 2.818879] PM: Adding info for No Bus:ptyb8
[ 2.819506] device: 'ptyb9': device_add
[ 2.819712] PM: Adding info for No Bus:ptyb9
[ 2.820514] device: 'ptyba': device_add
[ 2.820819] PM: Adding info for No Bus:ptyba
[ 2.821470] device: 'ptybb': device_add
[ 2.821681] PM: Adding info for No Bus:ptybb
[ 2.822314] device: 'ptybc': device_add
[ 2.822517] PM: Adding info for No Bus:ptybc
[ 2.823151] device: 'ptybd': device_add
[ 2.823355] PM: Adding info for No Bus:ptybd
[ 2.823992] device: 'ptybe': device_add
[ 2.825000] PM: Adding info for No Bus:ptybe
[ 2.825794] device: 'ptybf': device_add
[ 2.826066] PM: Adding info for No Bus:ptybf
[ 2.826725] device: 'ptyc0': device_add
[ 2.826966] PM: Adding info for No Bus:ptyc0
[ 2.827608] device: 'ptyc1': device_add
[ 2.827811] PM: Adding info for No Bus:ptyc1
[ 2.828545] device: 'ptyc2': device_add
[ 2.828766] PM: Adding info for No Bus:ptyc2
[ 2.829412] device: 'ptyc3': device_add
[ 2.829618] PM: Adding info for No Bus:ptyc3
[ 2.830250] device: 'ptyc4': device_add
[ 2.830456] PM: Adding info for No Bus:ptyc4
[ 2.831134] device: 'ptyc5': device_add
[ 2.831356] PM: Adding info for No Bus:ptyc5
[ 2.831992] device: 'ptyc6': device_add
[ 2.832998] PM: Adding info for No Bus:ptyc6
[ 2.833814] device: 'ptyc7': device_add
[ 2.834130] PM: Adding info for No Bus:ptyc7
[ 2.834784] device: 'ptyc8': device_add
[ 2.835052] PM: Adding info for No Bus:ptyc8
[ 2.835701] device: 'ptyc9': device_add
[ 2.835912] PM: Adding info for No Bus:ptyc9
[ 2.836647] device: 'ptyca': device_add
[ 2.836866] PM: Adding info for No Bus:ptyca
[ 2.837520] device: 'ptycb': device_add
[ 2.837761] PM: Adding info for No Bus:ptycb
[ 2.838441] device: 'ptycc': device_add
[ 2.838669] PM: Adding info for No Bus:ptycc
[ 2.839301] device: 'ptycd': device_add
[ 2.839508] PM: Adding info for No Bus:ptycd
[ 2.841016] device: 'ptyce': device_add
[ 2.841399] PM: Adding info for No Bus:ptyce
[ 2.842198] device: 'ptycf': device_add
[ 2.842432] PM: Adding info for No Bus:ptycf
[ 2.843091] device: 'ptyd0': device_add
[ 2.843298] PM: Adding info for No Bus:ptyd0
[ 2.843945] device: 'ptyd1': device_add
[ 2.844219] PM: Adding info for No Bus:ptyd1
[ 2.844978] device: 'ptyd2': device_add
[ 2.845248] PM: Adding info for No Bus:ptyd2
[ 2.845961] device: 'ptyd3': device_add
[ 2.846185] PM: Adding info for No Bus:ptyd3
[ 2.846824] device: 'ptyd4': device_add
[ 2.847069] PM: Adding info for No Bus:ptyd4
[ 2.847703] device: 'ptyd5': device_add
[ 2.847936] PM: Adding info for No Bus:ptyd5
[ 2.849490] device: 'ptyd6': device_add
[ 2.849827] PM: Adding info for No Bus:ptyd6
[ 2.850504] device: 'ptyd7': device_add
[ 2.850728] PM: Adding info for No Bus:ptyd7
[ 2.851393] device: 'ptyd8': device_add
[ 2.851622] PM: Adding info for No Bus:ptyd8
[ 2.852356] device: 'ptyd9': device_add
[ 2.852598] PM: Adding info for No Bus:ptyd9
[ 2.853269] device: 'ptyda': device_add
[ 2.853538] PM: Adding info for No Bus:ptyda
[ 2.854190] device: 'ptydb': device_add
[ 2.854453] PM: Adding info for No Bus:ptydb
[ 2.855107] device: 'ptydc': device_add
[ 2.855323] PM: Adding info for No Bus:ptydc
[ 2.855973] device: 'ptydd': device_add
[ 2.857035] PM: Adding info for No Bus:ptydd
[ 2.857845] device: 'ptyde': device_add
[ 2.858141] PM: Adding info for No Bus:ptyde
[ 2.858800] device: 'ptydf': device_add
[ 2.859029] PM: Adding info for No Bus:ptydf
[ 2.859675] device: 'ptye0': device_add
[ 2.859899] PM: Adding info for No Bus:ptye0
[ 2.860693] device: 'ptye1': device_add
[ 2.860997] PM: Adding info for No Bus:ptye1
[ 2.861645] device: 'ptye2': device_add
[ 2.861881] PM: Adding info for No Bus:ptye2
[ 2.862521] device: 'ptye3': device_add
[ 2.862743] PM: Adding info for No Bus:ptye3
[ 2.863425] device: 'ptye4': device_add
[ 2.863659] PM: Adding info for No Bus:ptye4
[ 2.865251] device: 'ptye5': device_add
[ 2.865601] PM: Adding info for No Bus:ptye5
[ 2.866334] device: 'ptye6': device_add
[ 2.866578] PM: Adding info for No Bus:ptye6
[ 2.867241] device: 'ptye7': device_add
[ 2.867476] PM: Adding info for No Bus:ptye7
[ 2.868192] device: 'ptye8': device_add
[ 2.868481] PM: Adding info for No Bus:ptye8
[ 2.869242] device: 'ptye9': device_add
[ 2.869530] PM: Adding info for No Bus:ptye9
[ 2.870176] device: 'ptyea': device_add
[ 2.870407] PM: Adding info for No Bus:ptyea
[ 2.871052] device: 'ptyeb': device_add
[ 2.871285] PM: Adding info for No Bus:ptyeb
[ 2.871926] device: 'ptyec': device_add
[ 2.872977] PM: Adding info for No Bus:ptyec
[ 2.873765] device: 'ptyed': device_add
[ 2.874101] PM: Adding info for No Bus:ptyed
[ 2.874769] device: 'ptyee': device_add
[ 2.875031] PM: Adding info for No Bus:ptyee
[ 2.875759] device: 'ptyef': device_add
[ 2.876019] PM: Adding info for No Bus:ptyef
[ 2.876833] device: 'ttyp0': device_add
[ 2.877088] PM: Adding info for No Bus:ttyp0
[ 2.877763] device: 'ttyp1': device_add
[ 2.877991] PM: Adding info for No Bus:ttyp1
[ 2.878637] device: 'ttyp2': device_add
[ 2.878853] PM: Adding info for No Bus:ttyp2
[ 2.879488] device: 'ttyp3': device_add
[ 2.879707] PM: Adding info for No Bus:ttyp3
[ 2.881236] device: 'ttyp4': device_add
[ 2.881595] PM: Adding info for No Bus:ttyp4
[ 2.882337] device: 'ttyp5': device_add
[ 2.882610] PM: Adding info for No Bus:ttyp5
[ 2.883275] device: 'ttyp6': device_add
[ 2.883512] PM: Adding info for No Bus:ttyp6
[ 2.884240] device: 'ttyp7': device_add
[ 2.884480] PM: Adding info for No Bus:ttyp7
[ 2.885159] device: 'ttyp8': device_add
[ 2.885379] PM: Adding info for No Bus:ttyp8
[ 2.886038] device: 'ttyp9': device_add
[ 2.886337] PM: Adding info for No Bus:ttyp9
[ 2.886991] device: 'ttypa': device_add
[ 2.887253] PM: Adding info for No Bus:ttypa
[ 2.887928] device: 'ttypb': device_add
[ 2.889046] PM: Adding info for No Bus:ttypb
[ 2.889831] device: 'ttypc': device_add
[ 2.890173] PM: Adding info for No Bus:ttypc
[ 2.890901] device: 'ttypd': device_add
[ 2.891158] PM: Adding info for No Bus:ttypd
[ 2.891818] device: 'ttype': device_add
[ 2.892045] PM: Adding info for No Bus:ttype
[ 2.892786] device: 'ttypf': device_add
[ 2.893071] PM: Adding info for No Bus:ttypf
[ 2.893839] device: 'ttyq0': device_add
[ 2.894127] PM: Adding info for No Bus:ttyq0
[ 2.894786] device: 'ttyq1': device_add
[ 2.895021] PM: Adding info for No Bus:ttyq1
[ 2.895659] device: 'ttyq2': device_add
[ 2.895921] PM: Adding info for No Bus:ttyq2
[ 2.897485] device: 'ttyq3': device_add
[ 2.897853] PM: Adding info for No Bus:ttyq3
[ 2.898554] device: 'ttyq4': device_add
[ 2.898791] PM: Adding info for No Bus:ttyq4
[ 2.899457] device: 'ttyq5': device_add
[ 2.899691] PM: Adding info for No Bus:ttyq5
[ 2.900425] device: 'ttyq6': device_add
[ 2.900674] PM: Adding info for No Bus:ttyq6
[ 2.901345] device: 'ttyq7': device_add
[ 2.901578] PM: Adding info for No Bus:ttyq7
[ 2.902233] device: 'ttyq8': device_add
[ 2.902468] PM: Adding info for No Bus:ttyq8
[ 2.903115] device: 'ttyq9': device_add
[ 2.903387] PM: Adding info for No Bus:ttyq9
[ 2.904044] device: 'ttyqa': device_add
[ 2.905105] PM: Adding info for No Bus:ttyqa
[ 2.905974] device: 'ttyqb': device_add
[ 2.906287] PM: Adding info for No Bus:ttyqb
[ 2.906968] device: 'ttyqc': device_add
[ 2.907215] PM: Adding info for No Bus:ttyqc
[ 2.907862] device: 'ttyqd': device_add
[ 2.908092] PM: Adding info for No Bus:ttyqd
[ 2.908822] device: 'ttyqe': device_add
[ 2.909084] PM: Adding info for No Bus:ttyqe
[ 2.909754] device: 'ttyqf': device_add
[ 2.910016] PM: Adding info for No Bus:ttyqf
[ 2.913418] device: 'ttyr0': device_add
[ 2.913806] PM: Adding info for No Bus:ttyr0
[ 2.914504] device: 'ttyr1': device_add
[ 2.914797] PM: Adding info for No Bus:ttyr1
[ 2.915476] device: 'ttyr2': device_add
[ 2.915719] PM: Adding info for No Bus:ttyr2
[ 2.916441] device: 'ttyr3': device_add
[ 2.916695] PM: Adding info for No Bus:ttyr3
[ 2.917366] device: 'ttyr4': device_add
[ 2.917604] PM: Adding info for No Bus:ttyr4
[ 2.918273] device: 'ttyr5': device_add
[ 2.918512] PM: Adding info for No Bus:ttyr5
[ 2.919168] device: 'ttyr6': device_add
[ 2.919445] PM: Adding info for No Bus:ttyr6
[ 2.920829] device: 'ttyr7': device_add
[ 2.921207] PM: Adding info for No Bus:ttyr7
[ 2.922011] device: 'ttyr8': device_add
[ 2.922269] PM: Adding info for No Bus:ttyr8
[ 2.922997] device: 'ttyr9': device_add
[ 2.923260] PM: Adding info for No Bus:ttyr9
[ 2.923913] device: 'ttyra': device_add
[ 2.924241] PM: Adding info for No Bus:ttyra
[ 2.924924] device: 'ttyrb': device_add
[ 2.925194] PM: Adding info for No Bus:ttyrb
[ 2.925853] device: 'ttyrc': device_add
[ 2.926133] PM: Adding info for No Bus:ttyrc
[ 2.926806] device: 'ttyrd': device_add
[ 2.927071] PM: Adding info for No Bus:ttyrd
[ 2.927741] device: 'ttyre': device_add
[ 2.927990] PM: Adding info for No Bus:ttyre
[ 2.929268] device: 'ttyrf': device_add
[ 2.929630] PM: Adding info for No Bus:ttyrf
[ 2.930307] device: 'ttys0': device_add
[ 2.930567] PM: Adding info for No Bus:ttys0
[ 2.931224] device: 'ttys1': device_add
[ 2.931480] PM: Adding info for No Bus:ttys1
[ 2.932211] device: 'ttys2': device_add
[ 2.932482] PM: Adding info for No Bus:ttys2
[ 2.933171] device: 'ttys3': device_add
[ 2.933503] PM: Adding info for No Bus:ttys3
[ 2.934171] device: 'ttys4': device_add
[ 2.934442] PM: Adding info for No Bus:ttys4
[ 2.935144] device: 'ttys5': device_add
[ 2.935410] PM: Adding info for No Bus:ttys5
[ 2.936084] device: 'ttys6': device_add
[ 2.937218] PM: Adding info for No Bus:ttys6
[ 2.938088] device: 'ttys7': device_add
[ 2.938409] PM: Adding info for No Bus:ttys7
[ 2.939089] device: 'ttys8': device_add
[ 2.939352] PM: Adding info for No Bus:ttys8
[ 2.940020] device: 'ttys9': device_add
[ 2.940365] PM: Adding info for No Bus:ttys9
[ 2.941041] device: 'ttysa': device_add
[ 2.941343] PM: Adding info for No Bus:ttysa
[ 2.942022] device: 'ttysb': device_add
[ 2.942282] PM: Adding info for No Bus:ttysb
[ 2.942945] device: 'ttysc': device_add
[ 2.943199] PM: Adding info for No Bus:ttysc
[ 2.943862] device: 'ttysd': device_add
[ 2.945066] PM: Adding info for No Bus:ttysd
[ 2.945885] device: 'ttyse': device_add
[ 2.946294] PM: Adding info for No Bus:ttyse
[ 2.946977] device: 'ttysf': device_add
[ 2.947250] PM: Adding info for No Bus:ttysf
[ 2.947907] device: 'ttyt0': device_add
[ 2.948284] PM: Adding info for No Bus:ttyt0
[ 2.948961] device: 'ttyt1': device_add
[ 2.949246] PM: Adding info for No Bus:ttyt1
[ 2.949890] device: 'ttyt2': device_add
[ 2.950152] PM: Adding info for No Bus:ttyt2
[ 2.950931] device: 'ttyt3': device_add
[ 2.951269] PM: Adding info for No Bus:ttyt3
[ 2.951920] device: 'ttyt4': device_add
[ 2.952963] PM: Adding info for No Bus:ttyt4
[ 2.953824] device: 'ttyt5': device_add
[ 2.954249] PM: Adding info for No Bus:ttyt5
[ 2.954932] device: 'ttyt6': device_add
[ 2.955219] PM: Adding info for No Bus:ttyt6
[ 2.955883] device: 'ttyt7': device_add
[ 2.956277] PM: Adding info for No Bus:ttyt7
[ 2.956962] device: 'ttyt8': device_add
[ 2.957246] PM: Adding info for No Bus:ttyt8
[ 2.957923] device: 'ttyt9': device_add
[ 2.958194] PM: Adding info for No Bus:ttyt9
[ 2.958859] device: 'ttyta': device_add
[ 2.959134] PM: Adding info for No Bus:ttyta
[ 2.959858] device: 'ttytb': device_add
[ 2.960829] PM: Adding info for No Bus:ttytb
[ 2.961591] device: 'ttytc': device_add
[ 2.961983] PM: Adding info for No Bus:ttytc
[ 2.962642] device: 'ttytd': device_add
[ 2.962954] PM: Adding info for No Bus:ttytd
[ 2.963618] device: 'ttyte': device_add
[ 2.963896] PM: Adding info for No Bus:ttyte
[ 2.964652] device: 'ttytf': device_add
[ 2.964954] PM: Adding info for No Bus:ttytf
[ 2.965621] device: 'ttyu0': device_add
[ 2.965901] PM: Adding info for No Bus:ttyu0
[ 2.966584] device: 'ttyu1': device_add
[ 2.966859] PM: Adding info for No Bus:ttyu1
[ 2.967533] device: 'ttyu2': device_add
[ 2.967806] PM: Adding info for No Bus:ttyu2
[ 2.969317] device: 'ttyu3': device_add
[ 2.969753] PM: Adding info for No Bus:ttyu3
[ 2.970474] device: 'ttyu4': device_add
[ 2.970804] PM: Adding info for No Bus:ttyu4
[ 2.971501] device: 'ttyu5': device_add
[ 2.971790] PM: Adding info for No Bus:ttyu5
[ 2.972550] device: 'ttyu6': device_add
[ 2.972851] PM: Adding info for No Bus:ttyu6
[ 2.973538] device: 'ttyu7': device_add
[ 2.973827] PM: Adding info for No Bus:ttyu7
[ 2.974487] device: 'ttyu8': device_add
[ 2.974820] PM: Adding info for No Bus:ttyu8
[ 2.975499] device: 'ttyu9': device_add
[ 2.975786] PM: Adding info for No Bus:ttyu9
[ 2.977178] device: 'ttyua': device_add
[ 2.977633] PM: Adding info for No Bus:ttyua
[ 2.978361] device: 'ttyub': device_add
[ 2.978695] PM: Adding info for No Bus:ttyub
[ 2.979368] device: 'ttyuc': device_add
[ 2.979660] PM: Adding info for No Bus:ttyuc
[ 2.980404] device: 'ttyud': device_add
[ 2.980714] PM: Adding info for No Bus:ttyud
[ 2.981398] device: 'ttyue': device_add
[ 2.981686] PM: Adding info for No Bus:ttyue
[ 2.982354] device: 'ttyuf': device_add
[ 2.982647] PM: Adding info for No Bus:ttyuf
[ 2.983339] device: 'ttyv0': device_add
[ 2.983628] PM: Adding info for No Bus:ttyv0
[ 2.985183] device: 'ttyv1': device_add
[ 2.985658] PM: Adding info for No Bus:ttyv1
[ 2.986405] device: 'ttyv2': device_add
[ 2.986709] PM: Adding info for No Bus:ttyv2
[ 2.987391] device: 'ttyv3': device_add
[ 2.987678] PM: Adding info for No Bus:ttyv3
[ 2.988439] device: 'ttyv4': device_add
[ 2.988739] PM: Adding info for No Bus:ttyv4
[ 2.989420] device: 'ttyv5': device_add
[ 2.989707] PM: Adding info for No Bus:ttyv5
[ 2.990359] device: 'ttyv6': device_add
[ 2.990646] PM: Adding info for No Bus:ttyv6
[ 2.991310] device: 'ttyv7': device_add
[ 2.991599] PM: Adding info for No Bus:ttyv7
[ 2.992987] device: 'ttyv8': device_add
[ 2.993462] PM: Adding info for No Bus:ttyv8
[ 2.994220] device: 'ttyv9': device_add
[ 2.994532] PM: Adding info for No Bus:ttyv9
[ 2.995227] device: 'ttyva': device_add
[ 2.995573] PM: Adding info for No Bus:ttyva
[ 2.996328] device: 'ttyvb': device_add
[ 2.996653] PM: Adding info for No Bus:ttyvb
[ 2.997342] device: 'ttyvc': device_add
[ 2.997638] PM: Adding info for No Bus:ttyvc
[ 2.998326] device: 'ttyvd': device_add
[ 2.998621] PM: Adding info for No Bus:ttyvd
[ 2.999296] device: 'ttyve': device_add
[ 2.999622] PM: Adding info for No Bus:ttyve
[ 3.001327] device: 'ttyvf': device_add
[ 3.001809] PM: Adding info for No Bus:ttyvf
[ 3.002545] device: 'ttyw0': device_add
[ 3.002859] PM: Adding info for No Bus:ttyw0
[ 3.003550] device: 'ttyw1': device_add
[ 3.003852] PM: Adding info for No Bus:ttyw1
[ 3.004599] device: 'ttyw2': device_add
[ 3.004916] PM: Adding info for No Bus:ttyw2
[ 3.005585] device: 'ttyw3': device_add
[ 3.005879] PM: Adding info for No Bus:ttyw3
[ 3.006656] device: 'ttyw4': device_add
[ 3.007031] PM: Adding info for No Bus:ttyw4
[ 3.007706] device: 'ttyw5': device_add
[ 3.008061] PM: Adding info for No Bus:ttyw5
[ 3.009530] device: 'ttyw6': device_add
[ 3.009989] PM: Adding info for No Bus:ttyw6
[ 3.010677] device: 'ttyw7': device_add
[ 3.010994] PM: Adding info for No Bus:ttyw7
[ 3.011651] device: 'ttyw8': device_add
[ 3.011960] PM: Adding info for No Bus:ttyw8
[ 3.012712] device: 'ttyw9': device_add
[ 3.013045] PM: Adding info for No Bus:ttyw9
[ 3.013726] device: 'ttywa': device_add
[ 3.014038] PM: Adding info for No Bus:ttywa
[ 3.014706] device: 'ttywb': device_add
[ 3.015048] PM: Adding info for No Bus:ttywb
[ 3.015729] device: 'ttywc': device_add
[ 3.016099] PM: Adding info for No Bus:ttywc
[ 3.017600] device: 'ttywd': device_add
[ 3.018080] PM: Adding info for No Bus:ttywd
[ 3.018796] device: 'ttywe': device_add
[ 3.019118] PM: Adding info for No Bus:ttywe
[ 3.019809] device: 'ttywf': device_add
[ 3.020194] PM: Adding info for No Bus:ttywf
[ 3.020907] device: 'ttyx0': device_add
[ 3.021239] PM: Adding info for No Bus:ttyx0
[ 3.021927] device: 'ttyx1': device_add
[ 3.022252] PM: Adding info for No Bus:ttyx1
[ 3.022926] device: 'ttyx2': device_add
[ 3.023287] PM: Adding info for No Bus:ttyx2
[ 3.023981] device: 'ttyx3': device_add
[ 3.025048] PM: Adding info for No Bus:ttyx3
[ 3.025850] device: 'ttyx4': device_add
[ 3.026241] PM: Adding info for No Bus:ttyx4
[ 3.026939] device: 'ttyx5': device_add
[ 3.027276] PM: Adding info for No Bus:ttyx5
[ 3.027939] device: 'ttyx6': device_add
[ 3.028358] PM: Adding info for No Bus:ttyx6
[ 3.029045] device: 'ttyx7': device_add
[ 3.029388] PM: Adding info for No Bus:ttyx7
[ 3.030081] device: 'ttyx8': device_add
[ 3.030443] PM: Adding info for No Bus:ttyx8
[ 3.031124] device: 'ttyx9': device_add
[ 3.031463] PM: Adding info for No Bus:ttyx9
[ 3.033058] device: 'ttyxa': device_add
[ 3.033568] PM: Adding info for No Bus:ttyxa
[ 3.034436] device: 'ttyxb': device_add
[ 3.034812] PM: Adding info for No Bus:ttyxb
[ 3.035501] device: 'ttyxc': device_add
[ 3.035834] PM: Adding info for No Bus:ttyxc
[ 3.036595] device: 'ttyxd': device_add
[ 3.036951] PM: Adding info for No Bus:ttyxd
[ 3.037636] device: 'ttyxe': device_add
[ 3.038017] PM: Adding info for No Bus:ttyxe
[ 3.038693] device: 'ttyxf': device_add
[ 3.039070] PM: Adding info for No Bus:ttyxf
[ 3.039873] device: 'ttyy0': device_add
[ 3.041092] PM: Adding info for No Bus:ttyy0
[ 3.041908] device: 'ttyy1': device_add
[ 3.042346] PM: Adding info for No Bus:ttyy1
[ 3.043061] device: 'ttyy2': device_add
[ 3.043415] PM: Adding info for No Bus:ttyy2
[ 3.044097] device: 'ttyy3': device_add
[ 3.044542] PM: Adding info for No Bus:ttyy3
[ 3.045243] device: 'ttyy4': device_add
[ 3.045586] PM: Adding info for No Bus:ttyy4
[ 3.046274] device: 'ttyy5': device_add
[ 3.046608] PM: Adding info for No Bus:ttyy5
[ 3.047297] device: 'ttyy6': device_add
[ 3.047663] PM: Adding info for No Bus:ttyy6
[ 3.049040] device: 'ttyy7': device_add
[ 3.049595] PM: Adding info for No Bus:ttyy7
[ 3.050329] device: 'ttyy8': device_add
[ 3.050709] PM: Adding info for No Bus:ttyy8
[ 3.051456] device: 'ttyy9': device_add
[ 3.051843] PM: Adding info for No Bus:ttyy9
[ 3.052625] device: 'ttyya': device_add
[ 3.052991] PM: Adding info for No Bus:ttyya
[ 3.053686] device: 'ttyyb': device_add
[ 3.054068] PM: Adding info for No Bus:ttyyb
[ 3.054765] device: 'ttyyc': device_add
[ 3.055155] PM: Adding info for No Bus:ttyyc
[ 3.055867] device: 'ttyyd': device_add
[ 3.056949] PM: Adding info for No Bus:ttyyd
[ 3.057762] device: 'ttyye': device_add
[ 3.058225] PM: Adding info for No Bus:ttyye
[ 3.058928] device: 'ttyyf': device_add
[ 3.059292] PM: Adding info for No Bus:ttyyf
[ 3.059983] device: 'ttyz0': device_add
[ 3.060431] PM: Adding info for No Bus:ttyz0
[ 3.061149] device: 'ttyz1': device_add
[ 3.061559] PM: Adding info for No Bus:ttyz1
[ 3.062254] device: 'ttyz2': device_add
[ 3.062610] PM: Adding info for No Bus:ttyz2
[ 3.063299] device: 'ttyz3': device_add
[ 3.063693] PM: Adding info for No Bus:ttyz3
[ 3.065280] device: 'ttyz4': device_add
[ 3.065785] PM: Adding info for No Bus:ttyz4
[ 3.066512] device: 'ttyz5': device_add
[ 3.066876] PM: Adding info for No Bus:ttyz5
[ 3.067571] device: 'ttyz6': device_add
[ 3.067933] PM: Adding info for No Bus:ttyz6
[ 3.068762] device: 'ttyz7': device_add
[ 3.069161] PM: Adding info for No Bus:ttyz7
[ 3.069855] device: 'ttyz8': device_add
[ 3.070219] PM: Adding info for No Bus:ttyz8
[ 3.070907] device: 'ttyz9': device_add
[ 3.071308] PM: Adding info for No Bus:ttyz9
[ 3.072097] device: 'ttyza': device_add
[ 3.073387] PM: Adding info for No Bus:ttyza
[ 3.074226] device: 'ttyzb': device_add
[ 3.074629] PM: Adding info for No Bus:ttyzb
[ 3.075357] device: 'ttyzc': device_add
[ 3.075738] PM: Adding info for No Bus:ttyzc
[ 3.076512] device: 'ttyzd': device_add
[ 3.076902] PM: Adding info for No Bus:ttyzd
[ 3.077591] device: 'ttyze': device_add
[ 3.077957] PM: Adding info for No Bus:ttyze
[ 3.078646] device: 'ttyzf': device_add
[ 3.079013] PM: Adding info for No Bus:ttyzf
[ 3.079705] device: 'ttya0': device_add
[ 3.080110] PM: Adding info for No Bus:ttya0
[ 3.081481] device: 'ttya1': device_add
[ 3.081970] PM: Adding info for No Bus:ttya1
[ 3.082682] device: 'ttya2': device_add
[ 3.083056] PM: Adding info for No Bus:ttya2
[ 3.083755] device: 'ttya3': device_add
[ 3.084254] PM: Adding info for No Bus:ttya3
[ 3.084963] device: 'ttya4': device_add
[ 3.085353] PM: Adding info for No Bus:ttya4
[ 3.086105] device: 'ttya5': device_add
[ 3.086509] PM: Adding info for No Bus:ttya5
[ 3.087195] device: 'ttya6': device_add
[ 3.087601] PM: Adding info for No Bus:ttya6
[ 3.088928] device: 'ttya7': device_add
[ 3.089449] PM: Adding info for No Bus:ttya7
[ 3.090221] device: 'ttya8': device_add
[ 3.090603] PM: Adding info for No Bus:ttya8
[ 3.091306] device: 'ttya9': device_add
[ 3.091689] PM: Adding info for No Bus:ttya9
[ 3.092453] device: 'ttyaa': device_add
[ 3.092863] PM: Adding info for No Bus:ttyaa
[ 3.093556] device: 'ttyab': device_add
[ 3.093937] PM: Adding info for No Bus:ttyab
[ 3.094618] device: 'ttyac': device_add
[ 3.094996] PM: Adding info for No Bus:ttyac
[ 3.095693] device: 'ttyad': device_add
[ 3.096102] PM: Adding info for No Bus:ttyad
[ 3.097814] device: 'ttyae': device_add
[ 3.098350] PM: Adding info for No Bus:ttyae
[ 3.099063] device: 'ttyaf': device_add
[ 3.099453] PM: Adding info for No Bus:ttyaf
[ 3.100221] device: 'ttyb0': device_add
[ 3.100629] PM: Adding info for No Bus:ttyb0
[ 3.101357] device: 'ttyb1': device_add
[ 3.101744] PM: Adding info for No Bus:ttyb1
[ 3.102439] device: 'ttyb2': device_add
[ 3.102823] PM: Adding info for No Bus:ttyb2
[ 3.103586] device: 'ttyb3': device_add
[ 3.103984] PM: Adding info for No Bus:ttyb3
[ 3.105545] device: 'ttyb4': device_add
[ 3.106152] PM: Adding info for No Bus:ttyb4
[ 3.106902] device: 'ttyb5': device_add
[ 3.107363] PM: Adding info for No Bus:ttyb5
[ 3.108065] device: 'ttyb6': device_add
[ 3.108564] PM: Adding info for No Bus:ttyb6
[ 3.109281] device: 'ttyb7': device_add
[ 3.109683] PM: Adding info for No Bus:ttyb7
[ 3.110376] device: 'ttyb8': device_add
[ 3.110767] PM: Adding info for No Bus:ttyb8
[ 3.111476] device: 'ttyb9': device_add
[ 3.111874] PM: Adding info for No Bus:ttyb9
[ 3.113339] device: 'ttyba': device_add
[ 3.113920] PM: Adding info for No Bus:ttyba
[ 3.114672] device: 'ttybb': device_add
[ 3.115076] PM: Adding info for No Bus:ttybb
[ 3.115785] device: 'ttybc': device_add
[ 3.116271] PM: Adding info for No Bus:ttybc
[ 3.116998] device: 'ttybd': device_add
[ 3.117410] PM: Adding info for No Bus:ttybd
[ 3.118119] device: 'ttybe': device_add
[ 3.118519] PM: Adding info for No Bus:ttybe
[ 3.119229] device: 'ttybf': device_add
[ 3.119624] PM: Adding info for No Bus:ttybf
[ 3.120983] device: 'ttyc0': device_add
[ 3.121501] PM: Adding info for No Bus:ttyc0
[ 3.122308] device: 'ttyc1': device_add
[ 3.122784] PM: Adding info for No Bus:ttyc1
[ 3.123488] device: 'ttyc2': device_add
[ 3.123895] PM: Adding info for No Bus:ttyc2
[ 3.124683] device: 'ttyc3': device_add
[ 3.125107] PM: Adding info for No Bus:ttyc3
[ 3.125819] device: 'ttyc4': device_add
[ 3.126230] PM: Adding info for No Bus:ttyc4
[ 3.126938] device: 'ttyc5': device_add
[ 3.127349] PM: Adding info for No Bus:ttyc5
[ 3.128047] device: 'ttyc6': device_add
[ 3.129421] PM: Adding info for No Bus:ttyc6
[ 3.130263] device: 'ttyc7': device_add
[ 3.130779] PM: Adding info for No Bus:ttyc7
[ 3.131507] device: 'ttyc8': device_add
[ 3.131942] PM: Adding info for No Bus:ttyc8
[ 3.132732] device: 'ttyc9': device_add
[ 3.133168] PM: Adding info for No Bus:ttyc9
[ 3.133871] device: 'ttyca': device_add
[ 3.134277] PM: Adding info for No Bus:ttyca
[ 3.134971] device: 'ttycb': device_add
[ 3.135411] PM: Adding info for No Bus:ttycb
[ 3.136809] device: 'ttycc': device_add
[ 3.137387] PM: Adding info for No Bus:ttycc
[ 3.138173] device: 'ttycd': device_add
[ 3.138608] PM: Adding info for No Bus:ttycd
[ 3.139338] device: 'ttyce': device_add
[ 3.139799] PM: Adding info for No Bus:ttyce
[ 3.140647] device: 'ttycf': device_add
[ 3.141117] PM: Adding info for No Bus:ttycf
[ 3.141826] device: 'ttyd0': device_add
[ 3.142240] PM: Adding info for No Bus:ttyd0
[ 3.142935] device: 'ttyd1': device_add
[ 3.143346] PM: Adding info for No Bus:ttyd1
[ 3.144049] device: 'ttyd2': device_add
[ 3.145147] PM: Adding info for No Bus:ttyd2
[ 3.145934] device: 'ttyd3': device_add
[ 3.146390] PM: Adding info for No Bus:ttyd3
[ 3.147090] device: 'ttyd4': device_add
[ 3.147548] PM: Adding info for No Bus:ttyd4
[ 3.148323] device: 'ttyd5': device_add
[ 3.148777] PM: Adding info for No Bus:ttyd5
[ 3.149492] device: 'ttyd6': device_add
[ 3.149922] PM: Adding info for No Bus:ttyd6
[ 3.150634] device: 'ttyd7': device_add
[ 3.151058] PM: Adding info for No Bus:ttyd7
[ 3.151771] device: 'ttyd8': device_add
[ 3.152835] PM: Adding info for No Bus:ttyd8
[ 3.153610] device: 'ttyd9': device_add
[ 3.154124] PM: Adding info for No Bus:ttyd9
[ 3.154847] device: 'ttyda': device_add
[ 3.155315] PM: Adding info for No Bus:ttyda
[ 3.156021] device: 'ttydb': device_add
[ 3.156580] PM: Adding info for No Bus:ttydb
[ 3.157301] device: 'ttydc': device_add
[ 3.157748] PM: Adding info for No Bus:ttydc
[ 3.158506] device: 'ttydd': device_add
[ 3.158958] PM: Adding info for No Bus:ttydd
[ 3.159652] device: 'ttyde': device_add
[ 3.160071] PM: Adding info for No Bus:ttyde
[ 3.161411] device: 'ttydf': device_add
[ 3.161970] PM: Adding info for No Bus:ttydf
[ 3.162672] device: 'ttye0': device_add
[ 3.163114] PM: Adding info for No Bus:ttye0
[ 3.163828] device: 'ttye1': device_add
[ 3.164344] PM: Adding info for No Bus:ttye1
[ 3.165058] device: 'ttye2': device_add
[ 3.165556] PM: Adding info for No Bus:ttye2
[ 3.166271] device: 'ttye3': device_add
[ 3.166716] PM: Adding info for No Bus:ttye3
[ 3.167411] device: 'ttye4': device_add
[ 3.167848] PM: Adding info for No Bus:ttye4
[ 3.169463] device: 'ttye5': device_add
[ 3.170105] PM: Adding info for No Bus:ttye5
[ 3.170840] device: 'ttye6': device_add
[ 3.171293] PM: Adding info for No Bus:ttye6
[ 3.172022] device: 'ttye7': device_add
[ 3.172569] PM: Adding info for No Bus:ttye7
[ 3.173286] device: 'ttye8': device_add
[ 3.173773] PM: Adding info for No Bus:ttye8
[ 3.174476] device: 'ttye9': device_add
[ 3.174934] PM: Adding info for No Bus:ttye9
[ 3.175647] device: 'ttyea': device_add
[ 3.176090] PM: Adding info for No Bus:ttyea
[ 3.177536] device: 'ttyeb': device_add
[ 3.178130] PM: Adding info for No Bus:ttyeb
[ 3.178868] device: 'ttyec': device_add
[ 3.179378] PM: Adding info for No Bus:ttyec
[ 3.180087] device: 'ttyed': device_add
[ 3.180644] PM: Adding info for No Bus:ttyed
[ 3.181376] device: 'ttyee': device_add
[ 3.181829] PM: Adding info for No Bus:ttyee
[ 3.182551] device: 'ttyef': device_add
[ 3.183043] PM: Adding info for No Bus:ttyef
[ 3.183984] device: 'ptmx': device_add
[ 3.185159] PM: Adding info for No Bus:ptmx
[ 3.186061] Initializing Nozomi driver 2.1d (build date: Jan 10 2009 13:32:38)
[ 3.186306] bus: 'pci': add driver nozomi
[ 3.187048] bus: 'virtio': add driver virtio_console
[ 3.187689] device class 'raw': registering
[ 3.188413] device: 'rawctl': device_add
[ 3.188721] PM: Adding info for No Bus:rawctl
[ 3.189537] device class 'printer': registering
[ 3.190230] lp: driver loaded but no devices found
[ 3.190349] Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $
[ 3.190484] ac.o: No PCI boards found.
[ 3.190580] ac.o: For an ISA board you must supply memory and irq parameters.
[ 3.190689] sonypi: Sony Programmable I/O Controller Driver v1.26.
[ 3.190800] toshiba: not a supported Toshiba laptop
[ 3.190937] device class 'ppdev': registering
[ 3.191558] ppdev: user-space parallel port driver
[ 3.191666] scx200_gpio: no SCx200 gpio present
[ 3.191765] nsc_gpio initializing
[ 3.191772] Linux agpgart interface v0.103
[ 3.191882] bus: 'pci': add driver agpgart-ali
[ 3.193536] bus: 'pci': add driver agpgart-amdk7
[ 3.194228] bus: 'pci': add driver agpgart-amd64
[ 3.194954] bus: 'pci': add driver agpgart-intel
[ 3.194999] bus: 'pci': driver_probe_device: matched device 0000:00:00.0 with driver agpgart-intel
[ 3.195010] bus: 'pci': really_probe: probing driver agpgart-intel with device 0000:00:00.0
[ 3.195073] agpgart-intel 0000:00:00.0: Intel 440BX Chipset
[ 3.201297] device: 'agpgart': device_add
[ 3.201731] PM: Adding info for No Bus:agpgart
[ 3.202664] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 3.202792] driver: '0000:00:00.0': driver_bound: bound to device 'agpgart-intel'
[ 3.202805] bus: 'pci': really_probe: bound device 0000:00:00.0 to driver agpgart-intel
[ 3.203508] bus: 'pci': add driver agpgart-sis
[ 3.204251] bus: 'pci': add driver agpgart-serverworks
[ 3.204927] bus: 'pci': add driver agpgart-via
[ 3.205608] ipwireless 1.1 by Stephen Blackheath, Ben Martel, Jiri Kosina and David Sterba
[ 3.205815] bus: 'pcmcia': add driver ipwireless
[ 3.206459] SyncLink PC Card driver $Revision: 4.34 $
[ 3.206570] bus: 'pcmcia': add driver synclink_cs
[ 3.207259] device: 'ttySLP0': device_add
[ 3.207957] PM: Adding info for No Bus:ttySLP0
[ 3.209468] device: 'ttySLP1': device_add
[ 3.210073] PM: Adding info for No Bus:ttySLP1
[ 3.210834] device: 'ttySLP2': device_add
[ 3.211297] PM: Adding info for No Bus:ttySLP2
[ 3.212079] device: 'ttySLP3': device_add
[ 3.212654] PM: Adding info for No Bus:ttySLP3
[ 3.213397] SyncLink PC Card driver $Revision: 4.34 $, tty major#250
[ 3.213521] cm4000_cs.c v2.4.0gm6 - All bugs added by Harald Welte
[ 3.213629] device class 'cardman_4000': registering
[ 3.214312] bus: 'pcmcia': add driver cm4000_cs
[ 3.214948] OMNIKEY CardMan 4040 v1.1.0gm5 - All bugs added by Harald Welte
[ 3.215070] device class 'cardman_4040': registering
[ 3.215730] bus: 'pcmcia': add driver cm4040_cs
[ 3.216833] device class 'drm': registering
[ 3.217508] [drm] Initialized drm 1.1.0 20060810
[ 3.218687] bus: 'pci': add driver i810fb
[ 3.219373] intelfb: intelfb_init
[ 3.219383] intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM chipsets
[ 3.219556] intelfb: Version 0.9.6
[ 3.219654] intelfb: intelfb_setup
[ 3.219660] intelfb: no options
[ 3.219674] bus: 'pci': add driver intelfb
[ 3.220414] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.220634] Registering platform device 'serial8250'. Parent at platform
[ 3.220645] device: 'serial8250': device_add
[ 3.220714] bus: 'platform': add device serial8250
[ 3.220777] PM: Adding info for platform:serial8250
[ 3.221739] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.221879] device: 'ttyS0': device_add
[ 3.222594] PM: Adding info for No Bus:ttyS0
[ 3.223607] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[ 3.223754] device: 'ttyS1': device_add
[ 3.225237] PM: Adding info for No Bus:ttyS1
[ 3.226144] device: 'ttyS2': device_add
[ 3.226778] PM: Adding info for No Bus:ttyS2
[ 3.227584] device: 'ttyS3': device_add
[ 3.228106] PM: Adding info for No Bus:ttyS3
[ 3.228947] bus: 'platform': add driver serial8250
[ 3.229011] bus: 'platform': driver_probe_device: matched device serial8250 with driver serial8250
[ 3.229023] bus: 'platform': really_probe: probing driver serial8250 with device serial8250
[ 3.229086] driver: 'serial8250': driver_bound: bound to device 'serial8250'
[ 3.229098] bus: 'platform': really_probe: bound device serial8250 to driver serial8250
[ 3.229729] bus: 'pci': add driver serial
[ 3.230560] bus: 'pcmcia': add driver serial_cs
[ 3.231394] bus: 'platform': add driver ax88796-pp
[ 3.233791] device: 'ram0': device_add
[ 3.233939] PM: Adding info for No Bus:ram0
[ 3.234936] device: '1:0': device_add
[ 3.235055] PM: Adding info for No Bus:1:0
[ 3.235822] device: 'ram1': device_add
[ 3.235942] PM: Adding info for No Bus:ram1
[ 3.236724] device: '1:1': device_add
[ 3.236808] PM: Adding info for No Bus:1:1
[ 3.237487] device: 'ram2': device_add
[ 3.237697] PM: Adding info for No Bus:ram2
[ 3.238350] device: '1:2': device_add
[ 3.238472] PM: Adding info for No Bus:1:2
[ 3.239183] device: 'ram3': device_add
[ 3.239300] PM: Adding info for No Bus:ram3
[ 3.239950] device: '1:3': device_add
[ 3.240026] PM: Adding info for No Bus:1:3
[ 3.241377] device: 'ram4': device_add
[ 3.241534] PM: Adding info for No Bus:ram4
[ 3.242212] device: '1:4': device_add
[ 3.242322] PM: Adding info for No Bus:1:4
[ 3.242991] device: 'ram5': device_add
[ 3.243106] PM: Adding info for No Bus:ram5
[ 3.243759] device: '1:5': device_add
[ 3.243834] PM: Adding info for No Bus:1:5
[ 3.244619] device: 'ram6': device_add
[ 3.244771] PM: Adding info for No Bus:ram6
[ 3.245440] device: '1:6': device_add
[ 3.245518] PM: Adding info for No Bus:1:6
[ 3.246217] device: 'ram7': device_add
[ 3.246334] PM: Adding info for No Bus:ram7
[ 3.246985] device: '1:7': device_add
[ 3.247063] PM: Adding info for No Bus:1:7
[ 3.247720] device: 'ram8': device_add
[ 3.247867] PM: Adding info for No Bus:ram8
[ 3.249278] device: '1:8': device_add
[ 3.249376] PM: Adding info for No Bus:1:8
[ 3.250125] device: 'ram9': device_add
[ 3.250255] PM: Adding info for No Bus:ram9
[ 3.250892] device: '1:9': device_add
[ 3.250972] PM: Adding info for No Bus:1:9
[ 3.251607] device: 'ram10': device_add
[ 3.251757] PM: Adding info for No Bus:ram10
[ 3.252475] device: '1:10': device_add
[ 3.252557] PM: Adding info for No Bus:1:10
[ 3.253294] device: 'ram11': device_add
[ 3.253419] PM: Adding info for No Bus:ram11
[ 3.254063] device: '1:11': device_add
[ 3.254170] PM: Adding info for No Bus:1:11
[ 3.254836] device: 'ram12': device_add
[ 3.254959] PM: Adding info for No Bus:ram12
[ 3.255655] device: '1:12': device_add
[ 3.255739] PM: Adding info for No Bus:1:12
[ 3.257522] device: 'ram13': device_add
[ 3.257672] PM: Adding info for No Bus:ram13
[ 3.258411] device: '1:13': device_add
[ 3.258530] PM: Adding info for No Bus:1:13
[ 3.259198] device: 'ram14': device_add
[ 3.259323] PM: Adding info for No Bus:ram14
[ 3.259952] device: '1:14': device_add
[ 3.260035] PM: Adding info for No Bus:1:14
[ 3.260763] device: 'ram15': device_add
[ 3.260892] PM: Adding info for No Bus:ram15
[ 3.261582] device: '1:15': device_add
[ 3.261664] PM: Adding info for No Bus:1:15
[ 3.262381] brd: module loaded
[ 3.262501] Compaq SMART2 Driver (v 2.6.0)
[ 3.262617] bus: 'pci': add driver cpqarray
[ 3.263452] bus: 'pci': remove driver cpqarray
[ 3.264063] driver: 'cpqarray': driver_release
[ 3.264098] bus: 'pci': add driver DAC960
[ 3.265769] device: 'dac960_gam': device_add
[ 3.266180] PM: Adding info for No Bus:dac960_gam
[ 3.266958] bus: 'pci': add driver umem
[ 3.267677] MM: desc_per_page = 128
[ 3.269615] nbd: registered device at major 43
[ 3.269746] device: 'nbd0': device_add
[ 3.269902] PM: Adding info for No Bus:nbd0
[ 3.271090] device: '43:0': device_add
[ 3.271176] PM: Adding info for No Bus:43:0
[ 3.271914] device: 'nbd1': device_add
[ 3.272041] PM: Adding info for No Bus:nbd1
[ 3.274159] device: '43:1': device_add
[ 3.274251] PM: Adding info for No Bus:43:1
[ 3.274966] device: 'nbd2': device_add
[ 3.275098] PM: Adding info for No Bus:nbd2
[ 3.275915] device: '43:2': device_add
[ 3.275990] PM: Adding info for No Bus:43:2
[ 3.276758] device: 'nbd3': device_add
[ 3.276884] PM: Adding info for No Bus:nbd3
[ 3.277693] device: '43:3': device_add
[ 3.277770] PM: Adding info for No Bus:43:3
[ 3.278407] device: 'nbd4': device_add
[ 3.278534] PM: Adding info for No Bus:nbd4
[ 3.279334] device: '43:4': device_add
[ 3.279412] PM: Adding info for No Bus:43:4
[ 3.281239] device: 'nbd5': device_add
[ 3.281397] PM: Adding info for No Bus:nbd5
[ 3.282390] device: '43:5': device_add
[ 3.282472] PM: Adding info for No Bus:43:5
[ 3.283150] device: 'nbd6': device_add
[ 3.283276] PM: Adding info for No Bus:nbd6
[ 3.284085] device: '43:6': device_add
[ 3.284226] PM: Adding info for No Bus:43:6
[ 3.284910] device: 'nbd7': device_add
[ 3.285040] PM: Adding info for No Bus:nbd7
[ 3.285845] device: '43:7': device_add
[ 3.285923] PM: Adding info for No Bus:43:7
[ 3.286652] device: 'nbd8': device_add
[ 3.286782] PM: Adding info for No Bus:nbd8
[ 3.287752] device: '43:8': device_add
[ 3.287837] PM: Adding info for No Bus:43:8
[ 3.289240] device: 'nbd9': device_add
[ 3.289385] PM: Adding info for No Bus:nbd9
[ 3.290270] device: '43:9': device_add
[ 3.290377] PM: Adding info for No Bus:43:9
[ 3.291073] device: 'nbd10': device_add
[ 3.291201] PM: Adding info for No Bus:nbd10
[ 3.291986] device: '43:10': device_add
[ 3.292095] PM: Adding info for No Bus:43:10
[ 3.292840] device: 'nbd11': device_add
[ 3.292977] PM: Adding info for No Bus:nbd11
[ 3.293782] device: '43:11': device_add
[ 3.293892] PM: Adding info for No Bus:43:11
[ 3.294650] device: 'nbd12': device_add
[ 3.294793] PM: Adding info for No Bus:nbd12
[ 3.295593] device: '43:12': device_add
[ 3.295708] PM: Adding info for No Bus:43:12
[ 3.297181] device: 'nbd13': device_add
[ 3.297335] PM: Adding info for No Bus:nbd13
[ 3.298225] device: '43:13': device_add
[ 3.298312] PM: Adding info for No Bus:43:13
[ 3.298984] device: 'nbd14': device_add
[ 3.299177] PM: Adding info for No Bus:nbd14
[ 3.300099] device: '43:14': device_add
[ 3.300245] PM: Adding info for No Bus:43:14
[ 3.300979] device: 'nbd15': device_add
[ 3.301140] PM: Adding info for No Bus:nbd15
[ 3.301955] device: '43:15': device_add
[ 3.302039] PM: Adding info for No Bus:43:15
[ 3.302722] bus: 'virtio': add driver virtio_blk
[ 3.303374] bus: 'pci': add driver sx8
[ 3.304110] bus: 'usb': add driver ub
[ 3.305576] usbcore: registered new interface driver ub
[ 3.306926] bus: 'platform': add driver pasic3
[ 3.307699] bus: 'platform': remove driver pasic3
[ 3.308370] driver: 'pasic3': driver_release
[ 3.308400] bus: 'i2c': add driver WM8400
[ 3.309052] i2c-core: driver [WM8400] registered
[ 3.309072] bus: 'i2c': add driver da903x
[ 3.309724] i2c-core: driver [da903x] registered
[ 3.309738] Intel(R) PRO/1000 Network Driver - version 7.3.20-k3-NAPI
[ 3.309856] Copyright (c) 1999-2006 Intel Corporation.
[ 3.309973] bus: 'pci': add driver e1000
[ 3.310647] Intel(R) Gigabit Ethernet Network Driver - version 1.2.45-k2
[ 3.310764] Copyright (c) 2008 Intel Corporation.
[ 3.310873] bus: 'pci': add driver igb
[ 3.311530] bus: 'pci': add driver Sundance Technology IPG Triple-Speed Ethernet
[ 3.312945] Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
[ 3.313077] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
[ 3.313882] device: 'bond0': device_add
[ 3.314295] PM: Adding info for No Bus:bond0
[ 3.317395] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 3.317520] Copyright (c) 2007 Atheros Corporation.
[ 3.317642] bus: 'pci': add driver atl2
[ 3.318523] jme: JMicron JMC250 gigabit ethernet driver version 1.0.3
[ 3.318649] bus: 'pci': add driver jme
[ 3.319334] bus: 'pci': add driver hme
[ 3.319990] bus: 'pci': add driver gem
[ 3.321474] bus: 'pci': add driver cassini
[ 3.322167] bus: 'pci': add driver 3c59x
[ 3.322231] bus: 'pci': driver_probe_device: matched device 0000:00:0b.0 with driver 3c59x
[ 3.322242] bus: 'pci': really_probe: probing driver 3c59x with device 0000:00:0b.0
[ 3.322318] 3c59x 0000:00:0b.0: found PCI INT A -> IRQ 10
[ 3.322534] 3c59x 0000:00:0b.0: sharing IRQ 10 with 0000:00:0a.0
[ 3.322682] 3c59x 0000:00:0b.0: sharing IRQ 10 with 0000:00:0b.1
[ 3.322903] 3c59x: Donald Becker and others.
[ 3.323048] 0000:00:0b.0: 3Com PCI 3c556 Laptop Tornado at e07f6400.
[ 3.345046] eth0 (3c59x): not using net_device_ops yet
[ 3.345168] device: 'eth0': device_add
[ 3.345582] PM: Adding info for No Bus:eth0
[ 3.348477] driver: '0000:00:0b.0': driver_bound: bound to device '3c59x'
[ 3.348494] bus: 'pci': really_probe: bound device 0000:00:0b.0 to driver 3c59x
[ 3.349226] bus: 'pci': add driver typhoon
[ 3.349943] bus: 'pci': add driver ne2k-pci
[ 3.350599] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
[ 3.350720] e100: Copyright(c) 1999-2006 Intel Corporation
[ 3.350836] bus: 'pci': add driver e100
[ 3.351512] ThunderLAN driver v1.15a
[ 3.351624] bus: 'pci': add driver tlan
[ 3.352912] TLAN: 0 devices installed, PCI: 0 EISA: 0
[ 3.353092] bus: 'pci': remove driver tlan
[ 3.353762] driver: 'tlan': driver_release
[ 3.353805] bus: 'pci': add driver smsc9420
[ 3.354510] bus: 'pci': add driver sis900
[ 3.355178] bus: 'pci': add driver r6040
[ 3.355856] bus: 'pci': add driver natsemi
[ 3.356749] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
[ 3.356887] bus: 'pci': add driver ns83820
[ 3.357603] bus: 'pci': add driver fealnx
[ 3.358276] bus: 'pci': add driver tg3
[ 3.359007] bus: 'pci': add driver via-rhine
[ 3.359656] bus: 'pci': add driver via-velocity
[ 3.360642] bus: 'mdio_bus': add driver Marvell 88E1101
[ 3.361329] bus: 'mdio_bus': add driver Marvell 88E1112
[ 3.361954] bus: 'mdio_bus': add driver Marvell 88E1111
[ 3.362569] bus: 'mdio_bus': add driver Marvell 88E1118
[ 3.363206] bus: 'mdio_bus': add driver Marvell 88E1145
[ 3.363830] bus: 'mdio_bus': add driver Marvell 88E1240
[ 3.364503] bus: 'mdio_bus': add driver Davicom DM9161E
[ 3.365170] bus: 'mdio_bus': add driver Davicom DM9161A
[ 3.365933] bus: 'mdio_bus': add driver Davicom DM9131
[ 3.366675] bus: 'mdio_bus': add driver Cicada Cis8204
[ 3.367288] bus: 'mdio_bus': add driver Cicada Cis8201
[ 3.367883] bus: 'mdio_bus': add driver LXT970
[ 3.369399] bus: 'mdio_bus': add driver LXT971
[ 3.370109] bus: 'mdio_bus': add driver QS6612
[ 3.370758] bus: 'mdio_bus': add driver SMSC LAN83C185
[ 3.371387] bus: 'mdio_bus': add driver SMSC LAN8187
[ 3.372001] bus: 'mdio_bus': add driver SMSC LAN8700
[ 3.372711] bus: 'mdio_bus': add driver SMSC LAN911x Internal PHY
[ 3.373346] bus: 'mdio_bus': add driver Broadcom BCM5411
[ 3.373990] bus: 'mdio_bus': add driver Broadcom BCM5421
[ 3.374590] bus: 'mdio_bus': add driver Broadcom BCM5461
[ 3.375253] bus: 'mdio_bus': add driver Broadcom BCM5464
[ 3.375910] bus: 'mdio_bus': add driver Broadcom BCM5481
[ 3.377637] bus: 'mdio_bus': add driver Broadcom BCM5482
[ 3.378345] bus: 'mdio_bus': add driver Broadcom BCM50610
[ 3.379033] bus: 'mdio_bus': add driver Broadcom BCM57780
[ 3.379666] bus: 'mdio_bus': add driver ICPlus IP175C
[ 3.380364] bus: 'mdio_bus': add driver RTL821x Gigabit Ethernet
[ 3.381014] Registering platform device 'Fixed MDIO bus.0'. Parent at platform
[ 3.381027] device: 'Fixed MDIO bus.0': device_add
[ 3.381069] bus: 'platform': add device Fixed MDIO bus.0
[ 3.381137] PM: Adding info for platform:Fixed MDIO bus.0
[ 3.381764] device: '0': device_add
[ 3.381888] PM: Adding info for No Bus:0
[ 3.382622] Fixed MDIO Bus: probed
[ 3.382753] bus: 'mdio_bus': add driver NatSemi DP83865
[ 3.383446] bus: 'pci': add driver sundance
[ 3.385430] D-Link DE-620 pocket adapter not identified in the printer port
[ 3.385688] bus: 'pci': add driver b44
[ 3.386692] bus: 'ssb': add driver b44
[ 3.387333] bus: 'pci': add driver forcedeth
[ 3.388022] bus: 'pci': add driver qla3xxx
[ 3.389928] PPP generic driver version 2.4.2
[ 3.390084] device class 'ppp': registering
[ 3.390760] device: 'ppp': device_add
[ 3.391161] PM: Adding info for No Bus:ppp
[ 3.392007] PPP Deflate Compression module registered
[ 3.392131] NET: Registered protocol family 24
[ 3.393013] device: 'dummy0': device_add
[ 3.393402] PM: Adding info for No Bus:dummy0
[ 3.396129] eth%d: D-Link DE-600 pocket adapter: not at I/O 0x378.
[ 3.396458] bus: 'pci': add driver 8139cp
[ 3.397267] bus: 'pci': add driver 8139too
[ 3.397935] Equalizer2002: Simon Janes ([email protected]) and David S. Miller ([email protected])
[ 3.398157] device: 'eql': device_add
[ 3.398534] PM: Adding info for No Bus:eql
[ 3.401669] bus: 'pci': add driver amd8111e
[ 3.402534] bus: 'spi': add driver enc28j60
[ 3.403176] bus: 'pci': add driver 3c359
[ 3.403849] arcnet loaded.
[ 3.403963] arcnet: raw mode (`r') encapsulation support loaded.
[ 3.404084] bus: 'pcmcia': add driver 3c589_cs
[ 3.404813] bus: 'pcmcia': add driver fmvj18x_cs
[ 3.405640] bus: 'pcmcia': add driver pcnet_cs
[ 3.406326] bus: 'pcmcia': add driver xirc2ps_cs
[ 3.406985] bus: 'pcmcia': add driver axnet_cs
[ 3.407609] bus: 'usb': add driver catc
[ 3.408786] usbcore: registered new interface driver catc
[ 3.408931] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 3.409044] bus: 'usb': add driver kaweth
[ 3.409777] usbcore: registered new interface driver kaweth
[ 3.409906] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 3.410067] bus: 'usb': add driver pegasus
[ 3.410687] usbcore: registered new interface driver pegasus
[ 3.410808] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[ 3.410921] bus: 'usb': add driver rtl8150
[ 3.411527] usbcore: registered new interface driver rtl8150
[ 3.411652] STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
[ 3.411821] bus: 'pcmcia': add driver netwave_cs
[ 3.412558] bus: 'pcmcia': add driver wavelan_cs
[ 3.413230] bus: 'pci': add driver xircom_cb
[ 3.413962] dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
[ 3.414099] bus: 'pci': add driver dmfe
[ 3.414815] bus: 'pci': add driver de2104x
[ 3.415495] bus: 'pci': add driver tulip
[ 3.416166] bus: 'pci': add driver de4x5
[ 3.417503] uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
[ 3.417655] bus: 'pci': add driver uli526x
[ 3.418338] AX.25: 6pack driver, Revision: 0.3.0
[ 3.418502] AX.25: bpqether driver version 004
[ 3.418606] baycom_ser_fdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA
[ 3.418611] baycom_ser_fdx: version 0.10 compiled 13:44:03 Jan 10 2009
[ 3.418870] bcsf0 (): not using net_device_ops yet
[ 3.418983] device: 'bcsf0': device_add
[ 3.419379] PM: Adding info for No Bus:bcsf0
[ 3.422342] bcsf1 (): not using net_device_ops yet
[ 3.422462] device: 'bcsf1': device_add
[ 3.422849] PM: Adding info for No Bus:bcsf1
[ 3.426670] bcsf2 (): not using net_device_ops yet
[ 3.426804] device: 'bcsf2': device_add
[ 3.427213] PM: Adding info for No Bus:bcsf2
[ 3.430648] bcsf3 (): not using net_device_ops yet
[ 3.430777] device: 'bcsf3': device_add
[ 3.431182] PM: Adding info for No Bus:bcsf3
[ 3.435246] hdlcdrv: (C) 1996-2000 Thomas Sailer HB9JNX/AE4WA
[ 3.435378] hdlcdrv: version 0.8 compiled 13:44:05 Jan 10 2009
[ 3.435486] baycom_ser_hdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA
[ 3.435491] baycom_ser_hdx: version 0.10 compiled 13:44:07 Jan 10 2009
[ 3.435766] bcsh0 (): not using net_device_ops yet
[ 3.435875] device: 'bcsh0': device_add
[ 3.436349] PM: Adding info for No Bus:bcsh0
[ 3.439730] bcsh1 (): not using net_device_ops yet
[ 3.439847] device: 'bcsh1': device_add
[ 3.440260] PM: Adding info for No Bus:bcsh1
[ 3.443635] bcsh2 (): not using net_device_ops yet
[ 3.443751] device: 'bcsh2': device_add
[ 3.444631] PM: Adding info for No Bus:bcsh2
[ 3.448136] bcsh3 (): not using net_device_ops yet
[ 3.448302] device: 'bcsh3': device_add
[ 3.448727] PM: Adding info for No Bus:bcsh3
[ 3.452645] baycom_par: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA
[ 3.452655] baycom_par: version 0.9 compiled 13:44:09 Jan 10 2009
[ 3.452925] bcp0 (): not using net_device_ops yet
[ 3.453033] device: 'bcp0': device_add
[ 3.453416] PM: Adding info for No Bus:bcp0
[ 3.457268] bcp1 (): not using net_device_ops yet
[ 3.457386] device: 'bcp1': device_add
[ 3.457766] PM: Adding info for No Bus:bcp1
[ 3.462078] bcp2 (): not using net_device_ops yet
[ 3.462204] device: 'bcp2': device_add
[ 3.462596] PM: Adding info for No Bus:bcp2
[ 3.466574] bcp3 (): not using net_device_ops yet
[ 3.466687] device: 'bcp3': device_add
[ 3.467070] PM: Adding info for No Bus:bcp3
[ 3.471310] baycom_epp: (C) 1998-2000 Thomas Sailer, HB9JNX/AE4WA
[ 3.471322] baycom_epp: version 0.7 compiled 13:44:10 Jan 10 2009
[ 3.471591] bce0 (): not using net_device_ops yet
[ 3.471699] device: 'bce0': device_add
[ 3.472085] PM: Adding info for No Bus:bce0
[ 3.476365] bce1 (): not using net_device_ops yet
[ 3.476483] device: 'bce1': device_add
[ 3.476869] PM: Adding info for No Bus:bce1
[ 3.481375] bce2 (): not using net_device_ops yet
[ 3.481490] device: 'bce2': device_add
[ 3.481881] PM: Adding info for No Bus:bce2
[ 3.486312] bce3 (): not using net_device_ops yet
[ 3.486427] device: 'bce3': device_add
[ 3.486845] PM: Adding info for No Bus:bce3
[ 3.491548] console [netcon0] enabled
[ 3.491665] netconsole: network logging started
[ 3.491772] bus: 'virtio': add driver virtio_net
[ 3.492525] Linux video capture interface: v2.00
[ 3.492647] device class 'video4linux': registering
[ 3.493265] bus: 'i2c': add driver tuner'
[ 3.493907] i2c-core: driver [tuner'] registered
[ 3.493925] bus: 'i2c': add driver tuner
[ 3.494581] i2c-core: driver [tuner] registered
[ 3.494597] bttv: driver version 0.9.17 loaded
[ 3.494706] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 3.494813] bttv: Host bridge needs ETBF enabled.
[ 3.495610] bus: 'bttv-sub': registered
[ 3.495649] bus: 'pci': add driver bttv
[ 3.496617] bus: 'i2c': add driver ir-kbd-i2c
[ 3.497266] i2c-core: driver [ir-kbd-i2c] registered
[ 3.497288] bus: 'i2c': add driver tvaudio'
[ 3.497910] i2c-core: driver [tvaudio'] registered
[ 3.497929] bus: 'i2c': add driver tvaudio
[ 3.498555] i2c-core: driver [tvaudio] registered
[ 3.498575] bus: 'i2c': add driver tda7432'
[ 3.499188] i2c-core: driver [tda7432'] registered
[ 3.499206] bus: 'i2c': add driver tda7432
[ 3.499847] i2c-core: driver [tda7432] registered
[ 3.499869] bus: 'i2c': add driver tda9875'
[ 3.500552] i2c-core: driver [tda9875'] registered
[ 3.500572] bus: 'i2c': add driver tda9875
[ 3.501200] i2c-core: driver [tda9875] registered
[ 3.501222] bus: 'i2c': add driver saa5246a'
[ 3.501839] i2c-core: driver [saa5246a'] registered
[ 3.501858] bus: 'i2c': add driver saa5246a
[ 3.502533] i2c-core: driver [saa5246a] registered
[ 3.502556] bus: 'i2c': add driver saa5249'
[ 3.503177] i2c-core: driver [saa5249'] registered
[ 3.503196] bus: 'i2c': add driver saa5249
[ 3.503823] i2c-core: driver [saa5249] registered
[ 3.503837] Colour QuickCam for Video4Linux v0.05
[ 3.503969] bus: 'i2c': add driver saa7110'
[ 3.504846] i2c-core: driver [saa7110'] registered
[ 3.504867] bus: 'i2c': add driver saa7110
[ 3.505533] i2c-core: driver [saa7110] registered
[ 3.505555] bus: 'i2c': add driver saa7115'
[ 3.506158] i2c-core: driver [saa7115'] registered
[ 3.506179] bus: 'i2c': add driver saa7115
[ 3.506781] i2c-core: driver [saa7115] registered
[ 3.506803] bus: 'i2c': add driver saa717x
[ 3.507498] i2c-core: driver [saa717x] registered
[ 3.507523] bus: 'i2c': add driver saa7127
[ 3.508450] i2c-core: driver [saa7127] registered
[ 3.508481] bus: 'i2c': add driver adv7175'
[ 3.509159] i2c-core: driver [adv7175'] registered
[ 3.509180] bus: 'i2c': add driver adv7175
[ 3.509789] i2c-core: driver [adv7175] registered
[ 3.509812] bus: 'i2c': add driver bt856'
[ 3.510447] i2c-core: driver [bt856'] registered
[ 3.510469] bus: 'i2c': add driver bt856
[ 3.511069] i2c-core: driver [bt856] registered
[ 3.511092] bus: 'i2c': add driver ks0127'
[ 3.511709] i2c-core: driver [ks0127'] registered
[ 3.511730] bus: 'i2c': add driver ks0127
[ 3.513256] i2c-core: driver [ks0127] registered
[ 3.513282] Zoran MJPEG board driver version 0.9.5
[ 3.513439] No known MJPEG cards found.
[ 3.513541] Linux video codec intermediate layer: v0.2
[ 3.513744] bus: 'pci': add driver stradis
[ 3.514595] V4L-Driver for Vision CPiA based cameras v1.2.3
[ 3.514712] Since in-kernel colorspace conversion is not allowed, it is disabled by default now. Users should fix the applications in case they don't work without conversion reenabled by setting the 'colorspace_conv' module parameter to 1
[ 3.515046] USB driver for Vision CPiA based cameras v1.2.3
[ 3.515160] bus: 'usb': add driver cpia
[ 3.515797] usbcore: registered new interface driver cpia
[ 3.515922] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 3.516048] bus: 'pci': add driver saa7134
[ 3.517065] bus: 'i2c': add driver saa6752hs'
[ 3.517733] i2c-core: driver [saa6752hs'] registered
[ 3.517757] bus: 'i2c': add driver saa6752hs
[ 3.518381] i2c-core: driver [saa6752hs] registered
[ 3.518405] bus: 'i2c': add driver msp3400'
[ 3.519069] i2c-core: driver [msp3400'] registered
[ 3.519091] bus: 'i2c': add driver msp3400
[ 3.519750] i2c-core: driver [msp3400] registered
[ 3.519774] bus: 'i2c': add driver cs5345
[ 3.521392] i2c-core: driver [cs5345] registered
[ 3.521433] bus: 'i2c': add driver cs53l32a'
[ 3.522170] i2c-core: driver [cs53l32a'] registered
[ 3.522194] bus: 'i2c': add driver cs53l32a
[ 3.522831] i2c-core: driver [cs53l32a] registered
[ 3.522855] bus: 'i2c': add driver m52790
[ 3.523498] i2c-core: driver [m52790] registered
[ 3.523523] bus: 'i2c': add driver wm8775'
[ 3.524149] i2c-core: driver [wm8775'] registered
[ 3.524170] bus: 'i2c': add driver wm8775
[ 3.524915] i2c-core: driver [wm8775] registered
[ 3.524939] bus: 'i2c': add driver wm8739
[ 3.525591] i2c-core: driver [wm8739] registered
[ 3.525614] bus: 'i2c': add driver vp27smpx
[ 3.526259] i2c-core: driver [vp27smpx] registered
[ 3.526275] cpia2: V4L-Driver for Vision CPiA2 based cameras v2.0.0
[ 3.526407] bus: 'usb': add driver cpia2
[ 3.527039] usbcore: registered new interface driver cpia2
[ 3.527164] saa7146: register extension 'hexium gemini'.
[ 3.527299] bus: 'pci': add driver hexium gemini
[ 3.528063] bus: 'i2c': add driver cx25840'
[ 3.529764] i2c-core: driver [cx25840'] registered
[ 3.529803] bus: 'i2c': add driver cx25840
[ 3.530508] i2c-core: driver [cx25840] registered
[ 3.530536] bus: 'i2c': add driver upd64031a
[ 3.531165] i2c-core: driver [upd64031a] registered
[ 3.531192] bus: 'i2c': add driver upd64083
[ 3.531812] i2c-core: driver [upd64083] registered
[ 3.531826] Marvell M88ALP01 'CAFE' Camera Controller version 2
[ 3.532023] bus: 'pci': add driver cafe1000-ccic
[ 3.532838] OmniVision ov7670 sensor driver, at your service
[ 3.532968] bus: 'i2c': add driver ov7670
[ 3.533595] i2c-core: driver [ov7670] registered
[ 3.533610] ivtv: Start initialization, version 1.4.0
[ 3.533735] bus: 'pci': add driver ivtv
[ 3.534402] ivtv: End initialization
[ 3.534523] ivtvfb: no cards found
[ 3.534619] cx18: Start initialization, version 1.0.4
[ 3.534735] bus: 'pci': add driver cx18
[ 3.535522] cx18: End initialization
[ 3.535634] cx23885 driver version 0.0.1 loaded
[ 3.535753] bus: 'pci': add driver cx23885
[ 3.538475] bus: 'soc-camera': registered
[ 3.538494] bus: 'soc-camera': add driver camera
[ 3.539147] bus: 'i2c': add driver mt9m001
[ 3.539823] i2c-core: driver [mt9m001] registered
[ 3.539849] bus: 'i2c': add driver mt9m111
[ 3.541405] i2c-core: driver [mt9m111] registered
[ 3.541446] bus: 'i2c': add driver mt9t031
[ 3.542191] i2c-core: driver [mt9t031] registered
[ 3.542218] bus: 'i2c': add driver ov772x
[ 3.542838] i2c-core: driver [ov772x] registered
[ 3.542862] bus: 'platform': add driver soc_camera_platform
[ 3.543497] bus: 'i2c': add driver tw9910
[ 3.544142] i2c-core: driver [tw9910] registered
[ 3.544155] au0828 driver loaded
[ 3.544337] bus: 'usb': add driver au0828
[ 3.545007] usbcore: registered new interface driver au0828
[ 3.545166] bus: 'pci': add driver radio-maxiradio
[ 3.545886] bus: 'usb': add driver dsbr100
[ 3.546518] usbcore: registered new interface driver dsbr100
[ 3.546650] dsbr100: v0.44:D-Link DSB-R100 USB FM radio driver
[ 3.546755] USB radio driver for Si470x FM Radio Receivers, Version 1.0.8
[ 3.546870] bus: 'usb': add driver radio-si470x
[ 3.547500] usbcore: registered new interface driver radio-si470x
[ 3.547632] bus: 'usb': add driver radio-mr800
[ 3.548809] usbcore: registered new interface driver radio-mr800
[ 3.548952] radio_mr800: version 0.01 AverMedia MR 800 USB FM radio driver
[ 3.549084] bus: 'i2c': add driver radio-tea5764
[ 3.549812] i2c-core: driver [radio-tea5764] registered
[ 3.549826] radio_tea5764: v0.01: A driver for the TEA5764 radio chip for EZX Phones.
[ 3.549991] bt878: AUDIO driver version 0.0.0 loaded
[ 3.550124] bus: 'pci': add driver bt878
[ 3.550857] bus: 'bttv-sub': add driver dvb-bt8xx
[ 3.551516] device: 'input0': device_add
[ 3.551712] PM: Adding info for No Bus:input0
[ 3.552853] input: Macintosh mouse button emulation as /class/input/input0
[ 3.553339] device class 'raid_devices': registering
[ 3.554056] device class 'spi_transport': registering
[ 3.554849] device class 'spi_host': registering
[ 3.555499] device class 'fc_host': registering
[ 3.556149] device class 'fc_vports': registering
[ 3.557952] device class 'fc_remote_ports': registering
[ 3.558590] device class 'fc_transport': registering
[ 3.559199] device class 'sas_host': registering
[ 3.559864] device class 'sas_phy': registering
[ 3.560553] device class 'sas_port': registering
[ 3.561144] device class 'sas_device': registering
[ 3.561737] device class 'sas_end_device': registering
[ 3.562315] device class 'sas_expander': registering
[ 3.562905] device class 'srp_host': registering
[ 3.563616] device class 'srp_remote_ports': registering
[ 3.565106] bus: 'pci': add driver aic7xxx
[ 3.566103] osst :I: Tape driver with OnStream support version 0.99.4
[ 3.566111] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 3.566339] device class 'onstream_tape': registering
[ 3.566997] Driver 'osst' needs updating - please use bus_type methods
[ 3.567116] bus: 'scsi': add driver osst
[ 3.567800] device class 'scsi_disk': registering
[ 3.568474] Driver 'sd' needs updating - please use bus_type methods
[ 3.568593] bus: 'scsi': add driver sd
[ 3.569222] SCSI Media Changer driver v0.25
[ 3.569333] device class 'scsi_changer': registering
[ 3.569986] Driver 'ch' needs updating - please use bus_type methods
[ 3.570103] bus: 'scsi': add driver ch
[ 3.570765] bus: 'pci': add driver ahci
[ 3.571539] bus: 'pci': add driver sata_svw
[ 3.573041] bus: 'pci': add driver ata_piix
[ 3.573186] bus: 'pci': driver_probe_device: matched device 0000:00:07.1 with driver ata_piix
[ 3.573198] bus: 'pci': really_probe: probing driver ata_piix with device 0000:00:07.1
[ 3.573244] ata_piix 0000:00:07.1: version 2.12
[ 3.574343] scsi0 : ata_piix
[ 3.577162] device: 'host0': device_add
[ 3.577227] PM: Adding info for No Bus:host0
[ 3.577244] device: 'host0': device_add
[ 3.577446] PM: Adding info for No Bus:host0
[ 3.578603] scsi1 : ata_piix
[ 3.578734] device: 'host1': device_add
[ 3.578801] PM: Adding info for No Bus:host1
[ 3.578815] device: 'host1': device_add
[ 3.578991] PM: Adding info for No Bus:host1
[ 3.579744] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1c20 irq 14
[ 3.579861] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1c28 irq 15
[ 3.744978] ata1.00: ATA-5: IC25N020ATCS04-0, CA2OA71A, max UDMA/100
[ 3.745110] ata1.00: 39070080 sectors, multi 16: LBA
[ 3.760835] ata1.00: configured for UDMA/33
[ 3.762158] scsi 0:0:0:0: Direct-Access ATA IC25N020ATCS04-0 CA2O PQ: 0 ANSI: 5
[ 3.762345] device: 'target0:0:0': device_add
[ 3.762421] PM: Adding info for No Bus:target0:0:0
[ 3.762442] device: '0:0:0:0': device_add
[ 3.762614] bus: 'scsi': add device 0:0:0:0
[ 3.762670] PM: Adding info for scsi:0:0:0:0
[ 3.763546] bus: 'scsi': driver_probe_device: matched device 0:0:0:0 with driver osst
[ 3.763559] bus: 'scsi': really_probe: probing driver osst with device 0:0:0:0
[ 3.763644] bus: 'scsi': driver_probe_device: matched device 0:0:0:0 with driver sd
[ 3.763655] bus: 'scsi': really_probe: probing driver sd with device 0:0:0:0
[ 3.763905] device: '0:0:0:0': device_add
[ 3.764040] PM: Adding info for No Bus:0:0:0:0
[ 3.765289] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 3.765623] sd 0:0:0:0: [sda] Write Protect is off
[ 3.765729] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.766032] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.766215] device: 'sda': device_add
[ 3.766448] PM: Adding info for No Bus:sda
[ 3.767039] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors: (20.0 GB/18.6 GiB)
[ 3.767365] sd 0:0:0:0: [sda] Write Protect is off
[ 3.767469] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.767789] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.767967] sda: sda1 sda2
[ 3.831524] device: 'sda1': device_add
[ 3.831746] PM: Adding info for No Bus:sda1
[ 3.831803] device: 'sda2': device_add
[ 3.831973] PM: Adding info for No Bus:sda2
[ 3.834316] device: '8:0': device_add
[ 3.834413] PM: Adding info for No Bus:8:0
[ 3.835116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.835237] driver: '0:0:0:0': driver_bound: bound to device 'sd'
[ 3.835249] bus: 'scsi': really_probe: bound device 0:0:0:0 to driver sd
[ 3.835272] device: '0:0:0:0': device_add
[ 3.835374] PM: Adding info for No Bus:0:0:0:0
[ 4.112738] ata2.00: ATAPI: QSI DVD-ROM SDR-081, EHA8, max UDMA/33
[ 4.120617] ata2.00: configured for UDMA/33
[ 4.121275] ------------[ cut here ]------------
[ 4.121380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x3d9/0x840()
[ 4.121538] Hardware name: HP OmniBook PC
[ 4.121644] Pid: 0, comm: swapper Not tainted 2.6.28-tip-10029-g20e9954-dirty #3
[ 4.121798] Call Trace:
[ 4.121912] [<c013d006>] warn_slowpath+0x86/0xa0
[ 4.122030] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122136] [<c0133270>] ? default_wake_function+0x10/0x20
[ 4.122260] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.122368] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122490] [<c06513d3>] ? ata_qc_complete_internal+0x13/0x20
[ 4.122602] [<c064f6ed>] ? __ata_qc_complete+0x6d/0xe0
[ 4.122710] [<c065e0a9>] ? ata_sff_qc_fill_rtf+0x19/0x30
[ 4.122817] [<c065fa07>] ? ata_sff_data_xfer32+0x77/0xd0
[ 4.122923] [<c0660739>] ata_sff_hsm_move+0x3d9/0x840
[ 4.123029] [<c034eb06>] ? _raw_spin_lock+0x46/0x170
[ 4.123134] [<c0660ef9>] ata_sff_interrupt+0x129/0x1e0
[ 4.123246] [<c0171dc0>] handle_IRQ_event+0x30/0x70
[ 4.123354] [<c0173b05>] handle_level_irq+0x75/0xe0
[ 4.123459] [<c0173a90>] ? handle_level_irq+0x0/0xe0
[ 4.123562] <IRQ> [<c0104607>] ? common_interrupt+0x27/0x2c
[ 4.123725] [<c0120120>] ? native_safe_halt+0x0/0x10
[ 4.123830] [<c012012a>] ? native_safe_halt+0xa/0x10
[ 4.123942] [<c010aaf9>] ? default_idle+0x69/0xa0
[ 4.124053] [<c015f792>] ? tick_nohz_restart_sched_tick+0x32/0x1b0
[ 4.124167] [<c011715f>] ? apm_cpu_idle+0xdf/0x260
[ 4.124273] [<c01027d8>] ? cpu_idle+0x78/0x100
[ 4.124379] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.124490] [<c09a92b3>] ? rest_init+0x53/0x60
[ 4.124601] [<c0e4d82a>] ? start_kernel+0x2ba/0x360
[ 4.124709] [<c0e4d260>] ? unknown_bootoption+0x0/0x210
[ 4.124820] [<c0e4d07c>] ? i386_start_kernel+0x7c/0xb0
[ 4.124948] ---[ end trace 83f9033b42a87df9 ]---
[ 4.126783] scsi 1:0:0:0: CD-ROM QSI DVD-ROM SDR-081 EHA8 PQ: 0 ANSI: 5
[ 4.126979] device: 'target1:0:0': device_add
[ 4.127040] PM: Adding info for No Bus:target1:0:0
[ 4.127057] device: '1:0:0:0': device_add
[ 4.127191] bus: 'scsi': add device 1:0:0:0
[ 4.127235] PM: Adding info for scsi:1:0:0:0
[ 4.127994] bus: 'scsi': driver_probe_device: matched device 1:0:0:0 with driver osst
[ 4.128007] bus: 'scsi': really_probe: probing driver osst with device 1:0:0:0
[ 4.128083] bus: 'scsi': driver_probe_device: matched device 1:0:0:0 with driver sd
[ 4.128093] bus: 'scsi': really_probe: probing driver sd with device 1:0:0:0
[ 4.128152] bus: 'scsi': driver_probe_device: matched device 1:0:0:0 with driver ch
[ 4.128161] bus: 'scsi': really_probe: probing driver ch with device 1:0:0:0
[ 4.128223] device: '1:0:0:0': device_add
[ 4.128340] PM: Adding info for No Bus:1:0:0:0
[ 4.128952] driver: '0000:00:07.1': driver_bound: bound to device 'ata_piix'
[ 4.128966] bus: 'pci': really_probe: bound device 0000:00:07.1 to driver ata_piix
[ 4.129567] bus: 'pci': add driver sata_promise
[ 4.130216] bus: 'pci': add driver sata_qstor
[ 4.130811] bus: 'pci': add driver sata_sil
[ 4.131391] bus: 'pci': add driver sata_sil24
[ 4.131985] bus: 'pci': add driver sata_via
[ 4.132641] bus: 'pci': add driver sata_vsc
[ 4.133293] bus: 'pci': add driver sata_sx4
[ 4.133907] bus: 'pci': add driver sata_nv
[ 4.134526] bus: 'pci': add driver sata_inic162x
[ 4.135146] bus: 'pci': add driver pdc_adma
[ 4.135786] bus: 'pci': add driver pata_ali
[ 4.136546] bus: 'pci': add driver pata_amd
[ 4.137187] bus: 'pci': add driver pata_artop
[ 4.137815] bus: 'pci': add driver pata_atiixp
[ 4.138443] bus: 'pci': add driver pata_cmd64x
[ 4.139096] bus: 'pci': add driver pata_cs5520
[ 4.139694] bus: 'pci': add driver cs5535
[ 4.140445] bus: 'pci': add driver pata_cs5536
[ 4.141155] bus: 'pci': add driver pata_cypress
[ 4.141923] bus: 'pci': add driver pata_efar
[ 4.142572] bus: 'pci': add driver pata_hpt37x
[ 4.143165] bus: 'pci': add driver pata_hpt3x2n
[ 4.143813] bus: 'pci': add driver pata_hpt3x3
[ 4.144878] bus: 'pci': add driver pata_it821x
[ 4.145639] bus: 'pci': add driver pata_it8213
[ 4.146257] bus: 'pci': add driver pata_jmicron
[ 4.146854] bus: 'pci': add driver pata_netcell
[ 4.147449] bus: 'pci': add driver pata_opti
[ 4.148052] bus: 'pci': add driver pata_optidma
[ 4.148715] bus: 'pci': add driver pata_marvell
[ 4.149323] bus: 'pci': add driver pata_mpiix
[ 4.149926] bus: 'pci': add driver pata_oldpiix
[ 4.150764] bus: 'pcmcia': add driver pata_pcmcia
[ 4.151397] bus: 'pci': add driver pata_pdc202xx_old
[ 4.152026] bus: 'pci': add driver pata_rz1000
[ 4.153694] bus: 'pci': add driver sc1200
[ 4.154439] bus: 'pci': add driver pata_serverworks
[ 4.155056] bus: 'pci': add driver pata_sil680
[ 4.155680] bus: 'pci': add driver pata_via
[ 4.156383] bus: 'pci': add driver pata_sl82c105
[ 4.157032] bus: 'pci': add driver pata_triflex
[ 4.157675] bus: 'pci': add driver ata_generic
[ 4.158286] I2O subsystem v1.325
[ 4.158402] i2o: max drivers = 8
[ 4.160136] bus: 'i2o': registered
[ 4.161394] bus: 'i2o': add driver exec-osm
[ 4.162224] bus: 'pci': add driver PCI_I2O
[ 4.162914] I2O Configuration OSM v1.323
[ 4.163037] bus: 'i2o': add driver config-osm
[ 4.163614] device: 'i2octl': device_add
[ 4.164007] PM: Adding info for No Bus:i2octl
[ 4.164676] I2O Bus Adapter OSM v1.317
[ 4.164794] bus: 'i2o': add driver bus-osm
[ 4.165333] I2O ProcFS OSM v1.316
[ 4.165438] bus: 'i2o': add driver proc-osm
[ 4.166025] Fusion MPT base driver 3.04.07
[ 4.166129] Copyright (c) 1999-2008 LSI Corporation
[ 4.166274] Fusion MPT SPI Host driver 3.04.07
[ 4.166434] bus: 'pci': add driver mptspi
[ 4.167108] Fusion MPT FC Host driver 3.04.07
[ 4.167314] bus: 'pci': add driver mptfc
[ 4.167935] Fusion MPT SAS Host driver 3.04.07
[ 4.168139] bus: 'pci': add driver mptsas
[ 4.171324] bus: 'firewire': registered
[ 4.171415] bus: 'pci': add driver firewire_ohci
[ 4.172367] bus: 'firewire': add driver sbp2
[ 4.172993] device class 'spidev': registering
[ 4.173554] bus: 'spi': add driver spidev
[ 4.174081] bus: 'spi': add driver tle62x0
[ 4.174719] bus: 'pci': add driver pd6729
[ 4.175402] bus: 'pci': add driver i82092aa
[ 4.176029] device class 'aoe': registering
[ 4.177235] device: 'err': device_add
[ 4.177634] PM: Adding info for No Bus:err
[ 4.178235] device: 'discover': device_add
[ 4.178481] PM: Adding info for No Bus:discover
[ 4.179076] device: 'interfaces': device_add
[ 4.179273] PM: Adding info for No Bus:interfaces
[ 4.179852] device: 'revalidate': device_add
[ 4.180044] PM: Adding info for No Bus:revalidate
[ 4.180701] device: 'flush': device_add
[ 4.180915] PM: Adding info for No Bus:flush
[ 4.182424] aoe: AoE v47 initialised.
[ 4.183045] device class 'uwb_rc': registering
[ 4.183694] bus: 'usb': add driver hwa-rc
[ 4.184259] usbcore: registered new interface driver hwa-rc
[ 4.184777] bus: 'platform': add driver gpio-vbus
[ 4.185419] bus: 'platform': remove driver gpio-vbus
[ 4.185917] driver: 'gpio-vbus': driver_release
[ 4.185967] device class 'usbmon': registering
[ 4.186622] device: 'usbmon0': device_add
[ 4.186991] PM: Adding info for No Bus:usbmon0
[ 4.187766] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.187891] ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
[ 4.187986] bus: 'pci': add driver ehci_hcd
[ 4.188826] bus: 'platform': add driver oxu210hp-hcd
[ 4.189370] 116x: driver isp116x-hcd, 03 Nov 2005
[ 4.189486] bus: 'platform': add driver isp116x-hcd
[ 4.190040] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.190154] ohci_hcd: block sizes: ed 64 td 64
[ 4.190232] bus: 'pci': add driver ohci_hcd
[ 4.190861] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.192054] bus: 'pci': add driver uhci_hcd
[ 4.192137] bus: 'pci': driver_probe_device: matched device 0000:00:07.2 with driver uhci_hcd
[ 4.192148] bus: 'pci': really_probe: probing driver uhci_hcd with device 0000:00:07.2
[ 4.192215] uhci_hcd 0000:00:07.2: found PCI INT D -> IRQ 10
[ 4.193220] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 4.193384] device: 'usb_host1': device_add
[ 4.193461] PM: Adding info for No Bus:usb_host1
[ 4.194353] device: 'usbmon1': device_add
[ 4.194780] PM: Adding info for No Bus:usbmon1
[ 4.195429] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 4.195624] uhci_hcd 0000:00:07.2: detected 2 ports
[ 4.195732] uhci_hcd 0000:00:07.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 4.195741] uhci_hcd 0000:00:07.2: Performing full reset
[ 4.195816] uhci_hcd 0000:00:07.2: irq 10, io base 0x00001c00
[ 4.196339] usb usb1: default language 0x0409
[ 4.196442] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.196553] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.196707] usb usb1: Product: UHCI Host Controller
[ 4.196809] usb usb1: Manufacturer: Linux 2.6.28-tip-10029-g20e9954-dirty uhci_hcd
[ 4.196964] usb usb1: SerialNumber: 0000:00:07.2
[ 4.197065] device: 'usb1': device_add
[ 4.197517] bus: 'usb': add device usb1
[ 4.197564] PM: Adding info for usb:usb1
[ 4.197689] usb usb1: uevent
[ 4.198341] bus: 'usb': driver_probe_device: matched device usb1 with driver usb
[ 4.198353] bus: 'usb': really_probe: probing driver usb with device usb1
[ 4.198391] usb usb1: usb_probe_device
[ 4.198402] usb usb1: configuration #1 chosen from 1 choice
[ 4.198572] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 4.198582] device: '1-0:1.0': device_add
[ 4.198651] bus: 'usb': add device 1-0:1.0
[ 4.198693] PM: Adding info for usb:1-0:1.0
[ 4.198751] usb 1-0:1.0: uevent
[ 4.199263] bus: 'usb': driver_probe_device: matched device 1-0:1.0 with driver hub
[ 4.199274] bus: 'usb': really_probe: probing driver hub with device 1-0:1.0
[ 4.199306] hub 1-0:1.0: usb_probe_interface
[ 4.199315] hub 1-0:1.0: usb_probe_interface - got id
[ 4.199325] hub 1-0:1.0: USB hub found
[ 4.199503] hub 1-0:1.0: 2 ports detected
[ 4.199601] hub 1-0:1.0: standalone hub
[ 4.199608] hub 1-0:1.0: no power switching (usb 1.0)
[ 4.199616] hub 1-0:1.0: individual port over-current protection
[ 4.199625] hub 1-0:1.0: power on to power good time: 2ms
[ 4.199672] hub 1-0:1.0: local power source is good
[ 4.199685] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 4.199732] driver: '1-0:1.0': driver_bound: bound to device 'hub'
[ 4.199744] bus: 'usb': really_probe: bound device 1-0:1.0 to driver hub
[ 4.199765] device class 'usb_endpoint': registering
[ 4.201212] device: 'usbdev1.1_ep81': device_add
[ 4.201693] PM: Adding info for No Bus:usbdev1.1_ep81
[ 4.202435] driver: 'usb1': driver_bound: bound to device 'usb'
[ 4.202448] bus: 'usb': really_probe: bound device usb1 to driver usb
[ 4.202486] device: 'usbdev1.1_ep00': device_add
[ 4.202782] PM: Adding info for No Bus:usbdev1.1_ep00
[ 4.203440] driver: '0000:00:07.2': driver_bound: bound to device 'uhci_hcd'
[ 4.203453] bus: 'pci': really_probe: bound device 0000:00:07.2 to driver uhci_hcd
[ 4.204000] r8a66597_hcd: driver r8a66597_hcd, 10 Apr 2008
[ 4.204134] bus: 'platform': add driver r8a66597_hcd
[ 4.206629] bus: 'pci': add driver isp1760
[ 4.207324] bus: 'usb': add driver hwa-hc
[ 4.207859] usbcore: registered new interface driver hwa-hc
[ 4.207997] bus: 'platform': add driver c67x00
[ 4.209665] bus: 'usb': add driver wusb-cbaf
[ 4.210349] usbcore: registered new interface driver wusb-cbaf
[ 4.210521] bus: 'usb': add driver cdc_acm
[ 4.211073] usbcore: registered new interface driver cdc_acm
[ 4.211194] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 4.211359] bus: 'usb': add driver cdc_wdm
[ 4.211944] usbcore: registered new interface driver cdc_wdm
[ 4.212065] Initializing USB Mass Storage driver...
[ 4.212176] bus: 'usb': add driver usb-storage
[ 4.212834] usbcore: registered new interface driver usb-storage
[ 4.212957] USB Mass Storage support registered.
[ 4.213070] bus: 'usb': add driver libusual
[ 4.213623] usbcore: registered new interface driver libusual
[ 4.213745] drivers/usb/misc/adutux.c : adu_init : enter
[ 4.213759] bus: 'usb': add driver adutux
[ 4.214436] usbcore: registered new interface driver adutux
[ 4.214566] adutux adutux (see http://www.ontrak.net) v0.0.13
[ 4.214668] adutux is an experimental driver. Use at your own risk
[ 4.214777] drivers/usb/misc/adutux.c : adu_init : leave, return value 0
[ 4.214998] bus: 'usb': add driver appledisplay
[ 4.215616] usbcore: registered new interface driver appledisplay
[ 4.215752] bus: 'usb': add driver berry_charge
[ 4.216960] usbcore: registered new interface driver berry_charge
[ 4.217122] bus: 'usb': add driver cypress_cy7c63
[ 4.217763] usbcore: registered new interface driver cypress_cy7c63
[ 4.217898] bus: 'usb': add driver cytherm
[ 4.218475] usbcore: registered new interface driver cytherm
[ 4.218593] cytherm: v1.0:Cypress USB Thermometer driver
[ 4.218703] bus: 'usb': add driver emi26 - firmware loader
[ 4.219278] usbcore: registered new interface driver emi26 - firmware loader
[ 4.219407] driver ftdi-elan built at 13:47:57 on Jan 10 2009
[ 4.220060] bus: 'usb': add driver ftdi-elan
[ 4.220754] usbcore: registered new interface driver ftdi-elan
[ 4.220883] idmouse: 0.6:Siemens ID Mouse FingerTIP Sensor Driver
[ 4.220999] bus: 'usb': add driver idmouse
[ 4.221565] usbcore: registered new interface driver idmouse
[ 4.221694] bus: 'usb': add driver iowarrior
[ 4.222230] usbcore: registered new interface driver iowarrior
[ 4.222357] bus: 'usb': add driver isight_firmware
[ 4.223068] usbcore: registered new interface driver isight_firmware
[ 4.223211] bus: 'usb': add driver usblcd
[ 4.223776] usbcore: registered new interface driver usblcd
[ 4.223907] bus: 'usb': add driver usbled
[ 4.225340] usbcore: registered new interface driver usbled
[ 4.225496] drivers/usb/misc/legousbtower.c: lego_usb_tower_init: enter
[ 4.225521] bus: 'usb': add driver legousbtower
[ 4.226165] usbcore: registered new interface driver legousbtower
[ 4.226291] legousbtower: v0.96:LEGO USB Tower Driver
[ 4.226394] drivers/usb/misc/legousbtower.c: lego_usb_tower_init: leave, return value 0
[ 4.226413] bus: 'usb': add driver rio500
[ 4.226953] usbcore: registered new interface driver rio500
[ 4.227073] rio500: v1.1:USB Rio 500 driver
[ 4.227182] bus: 'usb': add driver trancevibrator
[ 4.227721] usbcore: registered new interface driver trancevibrator
[ 4.227844] trancevibrator: v1.1:PlayStation 2 Trance Vibrator driver
[ 4.227960] bus: 'usb': add driver uss720
[ 4.228592] usbcore: registered new interface driver uss720
[ 4.228715] uss720: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip
[ 4.228877] uss720: NOTE: this is a special purpose driver to allow nonstandard
[ 4.229032] uss720: protocols (eg. bitbang) over USS720 usb to parallel cables
[ 4.229185] uss720: If you just want to connect to a printer, use usblp instead
[ 4.229350] bus: 'usb': add driver usbsevseg
[ 4.229900] usbcore: registered new interface driver usbsevseg
[ 4.230031] bus: 'usb': add driver vstusb
[ 4.230594] usbcore: registered new interface driver vstusb
[ 4.230794] bus: 'platform': add driver i8042
[ 4.231360] Registering platform device 'i8042'. Parent at platform
[ 4.231373] device: 'i8042': device_add
[ 4.231409] bus: 'platform': add device i8042
[ 4.231467] PM: Adding info for platform:i8042
[ 4.232026] bus: 'platform': driver_probe_device: matched device i8042 with driver i8042
[ 4.232040] bus: 'platform': really_probe: probing driver i8042 with device i8042
[ 4.239808] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.239956] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.240097] driver: 'i8042': driver_bound: bound to device 'i8042'
[ 4.240110] bus: 'platform': really_probe: bound device i8042 to driver i8042
[ 4.240134] parkbd: no such parport
[ 4.240350] bus: 'pci': add driver pcips2
[ 4.240692] device: 'serio0': device_add
[ 4.240727] bus: 'serio': add device serio0
[ 4.240796] PM: Adding info for serio:serio0
[ 4.241704] bus: 'serio': add driver serio_raw
[ 4.242433] device: 'serio1': device_add
[ 4.242467] bus: 'serio': add device serio1
[ 4.242532] PM: Adding info for serio:serio1
[ 4.242917] device: 'mice': device_add
[ 4.243338] PM: Adding info for No Bus:mice
[ 4.245699] device: 'mouse0': device_add
[ 4.246120] PM: Adding info for No Bus:mouse0
[ 4.246865] mice: PS/2 mouse device common for all mice
[ 4.247284] evbug.c: Connected device: input0 (Macintosh mouse button emulation at unknown)
[ 4.247312] bus: 'serio': add driver atkbd
[ 4.247883] bus: 'serio': add driver sunkbd
[ 4.248045] bus: 'serio': driver_probe_device: matched device serio0 with driver atkbd
[ 4.248057] bus: 'serio': really_probe: probing driver atkbd with device serio0
[ 4.248692] bus: 'serio': add driver xtkbd
[ 4.249252] bus: 'serio': add driver newtonkbd
[ 4.249802] bus: 'serio': add driver stowaway
[ 4.250530] bus: 'platform': add driver gpio-keys
[ 4.251128] bus: 'spi': add driver ads7846
[ 4.251754] bus: 'serio': add driver elo
[ 4.252385] bus: 'serio': add driver fujitsu_ts
[ 4.252950] bus: 'serio': add driver mtouch
[ 4.253503] mk712: device not present
[ 4.253645] bus: 'usb': add driver usbtouchscreen
[ 4.254236] usbcore: registered new interface driver usbtouchscreen
[ 4.254363] bus: 'serio': add driver penmountlpc
[ 4.254972] bus: 'serio': add driver touchright
[ 4.255550] bus: 'serio': add driver touchwin
[ 4.256165] bus: 'i2c': add driver tsc2007
[ 4.256797] i2c-core: driver [tsc2007] registered
[ 4.256823] bus: 'platform': add driver da9034-touch
[ 4.257397] bus: 'platform': add driver pcspkr
[ 4.257435] bus: 'platform': driver_probe_device: matched device pcspkr with driver pcspkr
[ 4.257446] bus: 'platform': really_probe: probing driver pcspkr with device pcspkr
[ 4.257522] device: 'input1': device_add
[ 4.257732] PM: Adding info for No Bus:input1
[ 4.258346] input: PC Speaker as /class/input/input1
[ 4.259902] evbug.c: Connected device: input1 (PC Speaker at isa0061/input0)
[ 4.259928] driver: 'pcspkr': driver_bound: bound to device 'pcspkr'
[ 4.259940] bus: 'platform': really_probe: bound device pcspkr to driver pcspkr
[ 4.260780] wistron_btns: System unknown
[ 4.260922] bus: 'usb': add driver ati_remote
[ 4.261567] usbcore: registered new interface driver ati_remote
[ 4.261692] ati_remote: 2.2.1:ATI/X10 RF USB Remote Control
[ 4.261808] bus: 'usb': add driver keyspan_remote
[ 4.262363] usbcore: registered new interface driver keyspan_remote
[ 4.262503] device: 'uinput': device_add
[ 4.262895] PM: Adding info for No Bus:uinput
[ 4.263908] apanel: Fujitsu BIOS signature 'FJKEYINF' not found...
[ 4.264046] bus: 'platform': add driver rtc-ds1286
[ 4.264879] bus: 'spi': add driver rtc-ds1305
[ 4.265476] bus: 'i2c': add driver rtc-ds1307
[ 4.266043] i2c-core: driver [rtc-ds1307] registered
[ 4.266069] bus: 'i2c': add driver rtc-ds1374
[ 4.266602] i2c-core: driver [rtc-ds1374] registered
[ 4.266619] bus: 'spi': add driver rtc-ds1390
[ 4.267158] bus: 'platform': add driver ds1511
[ 4.267715] bus: 'platform': add driver rtc-ds1553
[ 4.268390] bus: 'i2c': add driver rtc-ds1672
[ 4.269033] i2c-core: driver [rtc-ds1672] registered
[ 4.269057] bus: 'platform': add driver rtc-ds1742
[ 4.269623] bus: 'i2c': add driver rtc-fm3130
[ 4.270190] i2c-core: driver [rtc-fm3130] registered
[ 4.270219] bus: 'i2c': add driver rtc-isl1208
[ 4.270777] i2c-core: driver [rtc-isl1208] registered
[ 4.270799] bus: 'platform': add driver rtc-m48t35
[ 4.271368] bus: 'platform': add driver rtc-m48t59
[ 4.271999] bus: 'platform': add driver rtc-m48t86
[ 4.272646] bus: 'platform': add driver rtc-bq4802
[ 4.273242] bus: 'spi': add driver rtc-max6902
[ 4.273805] bus: 'i2c': add driver rtc-pcf8563
[ 4.274509] i2c-core: driver [rtc-pcf8563] registered
[ 4.274542] bus: 'i2c': add driver pcf8583
[ 4.275096] i2c-core: driver [pcf8583] registered
[ 4.275116] bus: 'spi': add driver rtc-r9701
[ 4.275652] bus: 'spi': add driver rtc-rs5c348
[ 4.276430] bus: 'i2c': add driver rtc-rx8581
[ 4.277001] i2c-core: driver [rtc-rx8581] registered
[ 4.277031] bus: 'i2c': add driver rtc-s35390a
[ 4.277566] i2c-core: driver [rtc-s35390a] registered
[ 4.277593] bus: 'platform': add driver stk17ta8
[ 4.278231] bus: 'platform': add driver rtc-test
[ 4.279009] Registering platform device 'rtc-test.0'. Parent at platform
[ 4.279023] device: 'rtc-test.0': device_add
[ 4.279067] bus: 'platform': add device rtc-test.0
[ 4.279125] PM: Adding info for platform:rtc-test.0
[ 4.279819] bus: 'platform': driver_probe_device: matched device rtc-test.0 with driver rtc-test
[ 4.279832] bus: 'platform': really_probe: probing driver rtc-test with device rtc-test.0
[ 4.279924] device: 'rtc0': device_add
[ 4.281069] PM: Adding info for No Bus:rtc0
[ 4.281885] test: dev (254:0)
[ 4.281940] rtc-test rtc-test.0: rtc core: registered test as rtc0
[ 4.282076] driver: 'rtc-test.0': driver_bound: bound to device 'rtc-test'
[ 4.282088] bus: 'platform': really_probe: bound device rtc-test.0 to driver rtc-test
[ 4.282108] Registering platform device 'rtc-test.1'. Parent at platform
[ 4.282117] device: 'rtc-test.1': device_add
[ 4.282153] bus: 'platform': add device rtc-test.1
[ 4.282240] PM: Adding info for platform:rtc-test.1
[ 4.282904] bus: 'platform': driver_probe_device: matched device rtc-test.1 with driver rtc-test
[ 4.282918] bus: 'platform': really_probe: probing driver rtc-test with device rtc-test.1
[ 4.282983] device: 'rtc1': device_add
[ 4.283363] PM: Adding info for No Bus:rtc1
[ 4.283984] test: dev (254:1)
[ 4.283993] rtc-test rtc-test.1: rtc core: registered test as rtc1
[ 4.284123] driver: 'rtc-test.1': driver_bound: bound to device 'rtc-test'
[ 4.284134] bus: 'platform': really_probe: bound device rtc-test.1 to driver rtc-test
[ 4.284172] bus: 'platform': add driver twl4030_rtc
[ 4.284827] bus: 'platform': add driver v3020
[ 4.285425] bus: 'i2c': add driver rtc-x1205
[ 4.286004] i2c-core: driver [rtc-x1205] registered
[ 4.286072] bus: 'pci': add driver ali1563_smbus
[ 4.286751] bus: 'pci': add driver ali15x3_smbus
[ 4.287378] bus: 'pci': add driver amd756_smbus
[ 4.288042] bus: 'pci': add driver amd8111_smbus2
[ 4.289669] bus: 'pci': add driver isch_smbus
[ 4.290057] device: 'input2': device_add
[ 4.290231] PM: Adding info for No Bus:input2
[ 4.291119] bus: 'pci': add driver nForce2_smbus
[ 4.291885] input: AT Translated Set 2 keyboard as /class/input/input2
[ 4.292197] bus: 'pci': add driver piix4_smbus
[ 4.292266] bus: 'pci': driver_probe_device: matched device 0000:00:07.3 with driver piix4_smbus
[ 4.292338] bus: 'pci': really_probe: probing driver piix4_smbus with device 0000:00:07.3
[ 4.292403] piix4_smbus 0000:00:07.3: Using Interrupt SMI# for SMBus.
[ 4.292416] piix4_smbus 0000:00:07.3: SMBus Host Controller at 0x2180, revision 0
[ 4.292622] device: 'i2c-0': device_add
[ 4.292732] PM: Adding info for No Bus:i2c-0
[ 4.293369] i2c-adapter i2c-0: adapter [SMBus PIIX4 adapter at 2180] registered
[ 4.293465] driver: '0000:00:07.3': driver_bound: bound to device 'piix4_smbus'
[ 4.293476] bus: 'pci': really_probe: bound device 0000:00:07.3 to driver piix4_smbus
[ 4.294102] bus: 'pci': add driver sis5595_smbus
[ 4.294743] bus: 'pci': add driver sis96x_smbus
[ 4.295379] bus: 'pci': add driver vt586b_smbus
[ 4.295970] i2c-parport: adapter type unspecified
[ 4.296085] i2c-parport-light: adapter type unspecified
[ 4.296196] bus: 'serio': add driver taos-evm
[ 4.297366] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 4.298022] bus: 'usb': add driver i2c-tiny-usb
[ 4.298647] usbcore: registered new interface driver i2c-tiny-usb
[ 4.298796] bus: 'platform': add driver i2c-pca-platform
[ 4.299389] scx200_i2c: NatSemi SCx200 I2C Driver
[ 4.299400] scx200_i2c: no SCx200 gpio pins available
[ 4.299536] bus: 'i2c': add driver ds1682
[ 4.300116] i2c-core: driver [ds1682] registered
[ 4.300148] bus: 'i2c': add driver at24
[ 4.300816] i2c-core: driver [at24] registered
[ 4.300848] bus: 'i2c': add driver eeprom
[ 4.301396] i2c-core: driver [eeprom] registered
[ 4.301421] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x50
[ 4.301455] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a0, DAT0=04, DAT1=00
[ 4.303714] evbug.c: Connected device: input2 (AT Translated Set 2 keyboard at isa0060/serio0/input0)
[ 4.303747] driver: 'serio0': driver_bound: bound to device 'atkbd'
[ 4.303760] bus: 'serio': really_probe: bound device serio0 to driver atkbd
[ 4.303779] bus: 'serio': driver_probe_device: matched device serio1 with driver atkbd
[ 4.303788] bus: 'serio': really_probe: probing driver atkbd with device serio1
[ 4.308353] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a0, DAT0=04, DAT1=00
[ 4.308388] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a0, DAT0=04, DAT1=00
[ 4.316330] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a0, DAT0=04, DAT1=00
[ 4.316344] i2c-adapter i2c-0: Creating eeprom at 0x50
[ 4.316375] device: '0-0050': device_add
[ 4.316413] bus: 'i2c': add device 0-0050
[ 4.316469] PM: Adding info for i2c:0-0050
[ 4.316531] i2c 0-0050: uevent
[ 4.317313] bus: 'i2c': driver_probe_device: matched device 0-0050 with driver eeprom
[ 4.317327] bus: 'i2c': really_probe: probing driver eeprom with device 0-0050
[ 4.317359] eeprom 0-0050: probe
[ 4.317382] driver: '0-0050': driver_bound: bound to device 'eeprom'
[ 4.317393] bus: 'i2c': really_probe: bound device 0-0050 to driver eeprom
[ 4.317409] i2c-adapter i2c-0: client [eeprom] registered with bus id 0-0050
[ 4.317421] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x51
[ 4.317452] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a2, DAT0=04, DAT1=00
[ 4.324312] i2c-adapter i2c-0: Error: no response!
[ 4.324341] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a2, DAT0=04, DAT1=00
[ 4.324352] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x52
[ 4.324382] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a4, DAT0=04, DAT1=00
[ 4.332308] i2c-adapter i2c-0: Error: no response!
[ 4.332337] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a4, DAT0=04, DAT1=00
[ 4.332348] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x53
[ 4.332376] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a6, DAT0=04, DAT1=00
[ 4.340309] i2c-adapter i2c-0: Error: no response!
[ 4.340338] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a6, DAT0=04, DAT1=00
[ 4.340349] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x54
[ 4.340377] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=a8, DAT0=04, DAT1=00
[ 4.348312] i2c-adapter i2c-0: Error: no response!
[ 4.348341] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=a8, DAT0=04, DAT1=00
[ 4.348351] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x55
[ 4.348380] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=aa, DAT0=04, DAT1=00
[ 4.356320] i2c-adapter i2c-0: Error: no response!
[ 4.356348] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=aa, DAT0=04, DAT1=00
[ 4.356359] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x56
[ 4.356388] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=ac, DAT0=04, DAT1=00
[ 4.364312] i2c-adapter i2c-0: Error: no response!
[ 4.364341] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=ac, DAT0=04, DAT1=00
[ 4.364352] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x57
[ 4.364380] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=ae, DAT0=04, DAT1=00
[ 4.372313] i2c-adapter i2c-0: Error: no response!
[ 4.372342] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=ae, DAT0=04, DAT1=00
[ 4.372397] bus: 'i2c': add driver max6875
[ 4.373048] i2c-core: driver [max6875] registered
[ 4.373093] bus: 'i2c': add driver pcf8591
[ 4.373654] i2c-core: driver [pcf8591] registered
[ 4.373677] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x48
[ 4.373710] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.380316] i2c-adapter i2c-0: Error: no response!
[ 4.380347] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.380358] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x49
[ 4.380388] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.388315] i2c-adapter i2c-0: Error: no response!
[ 4.388344] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.388355] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4a
[ 4.388383] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.396316] i2c-adapter i2c-0: Error: no response!
[ 4.396345] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.396356] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4b
[ 4.396384] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.404317] i2c-adapter i2c-0: Error: no response!
[ 4.404346] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.404357] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 4.404385] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.412318] i2c-adapter i2c-0: Error: no response!
[ 4.412347] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.412358] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4d
[ 4.412386] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 4.420319] i2c-adapter i2c-0: Error: no response!
[ 4.420348] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 4.420359] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4e
[ 4.420387] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 4.428320] i2c-adapter i2c-0: Error: no response!
[ 4.428349] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 4.428360] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4f
[ 4.428388] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9e, DAT0=04, DAT1=00
[ 4.436321] i2c-adapter i2c-0: Error: no response!
[ 4.436350] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9e, DAT0=04, DAT1=00
[ 4.436368] Driver for 1-wire Dallas network protocol.
[ 4.437079] bus: 'w1': registered
[ 4.437090] bus: 'w1': add driver w1_master_driver
[ 4.437599] bus: 'w1': add driver w1_slave_driver
[ 4.438186] bus: 'pci': add driver matrox_w1
[ 4.438846] bus: 'platform': add driver w1-gpio
[ 4.439474] bus: 'platform': remove driver w1-gpio
[ 4.439977] driver: 'w1-gpio': driver_release
[ 4.440002] 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
[ 4.440194] bus: 'platform': add driver pda-power
[ 4.440833] bus: 'platform': add driver ds2760-battery
[ 4.441468] bus: 'i2c': add driver bq27200-battery
[ 4.442035] i2c-core: driver [bq27200-battery] registered
[ 4.442062] bus: 'platform': add driver da903x-battery
[ 4.442658] bus: 'i2c': add driver asb100
[ 4.443225] i2c-core: driver [asb100] registered
[ 4.443250] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.443284] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.448330] i2c-adapter i2c-0: Error: no response!
[ 4.448363] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.448420] bus: 'i2c': add driver w83792d
[ 4.449120] i2c-core: driver [w83792d] registered
[ 4.449145] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.449179] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.456326] i2c-adapter i2c-0: Error: no response!
[ 4.456355] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.456367] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.456396] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.464325] i2c-adapter i2c-0: Error: no response!
[ 4.464353] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.464364] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.464392] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.472325] i2c-adapter i2c-0: Error: no response!
[ 4.472354] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.472365] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.472393] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.480327] i2c-adapter i2c-0: Error: no response!
[ 4.480355] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.480395] bus: 'i2c': add driver w83793
[ 4.480955] i2c-core: driver [w83793] registered
[ 4.480977] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.481008] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.488330] i2c-adapter i2c-0: Error: no response!
[ 4.488359] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.488370] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.488399] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.496328] i2c-adapter i2c-0: Error: no response!
[ 4.496357] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.496368] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.496396] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.504329] i2c-adapter i2c-0: Error: no response!
[ 4.504358] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.504368] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.504397] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.512330] i2c-adapter i2c-0: Error: no response!
[ 4.512359] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.512396] bus: 'i2c': add driver w83781d
[ 4.512933] i2c-core: driver [w83781d] registered
[ 4.512956] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x28
[ 4.512987] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.520334] i2c-adapter i2c-0: Error: no response!
[ 4.520363] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.520374] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 4.520403] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.528332] i2c-adapter i2c-0: Error: no response!
[ 4.528361] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.528371] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 4.528400] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.536333] i2c-adapter i2c-0: Error: no response!
[ 4.536362] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.536372] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 4.536401] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.544334] i2c-adapter i2c-0: Error: no response!
[ 4.544363] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.544373] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.544402] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.552335] i2c-adapter i2c-0: Error: no response!
[ 4.552363] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.552374] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.552403] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.560336] i2c-adapter i2c-0: Error: no response!
[ 4.560364] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.560375] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.560404] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.568337] i2c-adapter i2c-0: Error: no response!
[ 4.568365] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.568376] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.568404] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.576338] i2c-adapter i2c-0: Error: no response!
[ 4.576370] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.576408] bus: 'i2c': add driver w83791d
[ 4.576953] i2c-core: driver [w83791d] registered
[ 4.576974] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.577005] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.584342] i2c-adapter i2c-0: Error: no response!
[ 4.584371] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.584382] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.584411] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.592340] i2c-adapter i2c-0: Error: no response!
[ 4.592369] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.592379] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.592410] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.600341] i2c-adapter i2c-0: Error: no response!
[ 4.600369] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.600380] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.600408] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.608342] i2c-adapter i2c-0: Error: no response!
[ 4.608370] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.608413] bus: 'i2c': add driver ad7414
[ 4.609005] i2c-core: driver [ad7414] registered
[ 4.609037] bus: 'i2c': add driver ad7418
[ 4.609581] i2c-core: driver [ad7418] registered
[ 4.609603] bus: 'spi': add driver adcxx1s
[ 4.610163] bus: 'spi': add driver adcxx2s
[ 4.610678] bus: 'spi': add driver adcxx4s
[ 4.611198] bus: 'spi': add driver adcxx8s
[ 4.611762] bus: 'i2c': add driver adm1021
[ 4.612391] i2c-core: driver [adm1021] registered
[ 4.612419] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x18
[ 4.612454] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 4.620349] i2c-adapter i2c-0: Error: no response!
[ 4.620380] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 4.620392] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x19
[ 4.620422] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 4.628345] i2c-adapter i2c-0: Error: no response!
[ 4.628373] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 4.628384] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1a
[ 4.628412] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 4.636345] i2c-adapter i2c-0: Error: no response!
[ 4.636374] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 4.636385] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 4.636413] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.644346] i2c-adapter i2c-0: Error: no response!
[ 4.644375] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.644386] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 4.644414] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.652347] i2c-adapter i2c-0: Error: no response!
[ 4.652376] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.652387] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 4.652415] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.660348] i2c-adapter i2c-0: Error: no response!
[ 4.660377] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.660387] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 4.660416] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.668349] i2c-adapter i2c-0: Error: no response!
[ 4.668378] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.668388] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4d
[ 4.668417] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 4.676350] i2c-adapter i2c-0: Error: no response!
[ 4.676379] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 4.676389] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4e
[ 4.676418] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 4.684351] i2c-adapter i2c-0: Error: no response!
[ 4.684380] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 4.684430] bus: 'i2c': add driver adm1025
[ 4.685085] i2c-core: driver [adm1025] registered
[ 4.685110] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.685141] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.692355] i2c-adapter i2c-0: Error: no response!
[ 4.692385] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.692396] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.692424] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.700353] i2c-adapter i2c-0: Error: no response!
[ 4.700382] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.700392] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.700421] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.708354] i2c-adapter i2c-0: Error: no response!
[ 4.708383] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.708424] bus: 'i2c': add driver adm1029
[ 4.708978] i2c-core: driver [adm1029] registered
[ 4.709002] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x28
[ 4.709033] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.716357] i2c-adapter i2c-0: Error: no response!
[ 4.716386] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.716397] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 4.716426] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.724371] i2c-adapter i2c-0: Error: no response!
[ 4.724400] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.724411] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 4.724439] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.732357] i2c-adapter i2c-0: Error: no response!
[ 4.732386] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 4.732396] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 4.732425] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.740358] i2c-adapter i2c-0: Error: no response!
[ 4.740387] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 4.740397] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.740426] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.748358] i2c-adapter i2c-0: Error: no response!
[ 4.748388] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.748398] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.748426] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.756359] i2c-adapter i2c-0: Error: no response!
[ 4.756388] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.756399] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.756427] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.764360] i2c-adapter i2c-0: Error: no response!
[ 4.764389] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.764400] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.764428] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.772365] i2c-adapter i2c-0: Error: no response!
[ 4.772393] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.772434] bus: 'i2c': add driver adm1031
[ 4.772986] i2c-core: driver [adm1031] registered
[ 4.773010] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.773041] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.780365] i2c-adapter i2c-0: Error: no response!
[ 4.780394] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.780405] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.780434] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.788363] i2c-adapter i2c-0: Error: no response!
[ 4.788392] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.788403] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.788431] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.796364] i2c-adapter i2c-0: Error: no response!
[ 4.796393] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.796433] bus: 'i2c': add driver ads7828
[ 4.796974] i2c-core: driver [ads7828] registered
[ 4.796998] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x48
[ 4.797028] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.804367] i2c-adapter i2c-0: Error: no response!
[ 4.804397] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.804408] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x49
[ 4.804437] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.812366] i2c-adapter i2c-0: Error: no response!
[ 4.812395] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.812406] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4a
[ 4.812434] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.820367] i2c-adapter i2c-0: Error: no response!
[ 4.820396] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.820407] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4b
[ 4.820435] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.828368] i2c-adapter i2c-0: Error: no response!
[ 4.828397] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.828437] bus: 'i2c': add driver adt7462
[ 4.828983] i2c-core: driver [adt7462] registered
[ 4.829007] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x58
[ 4.829038] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=b0, DAT0=04, DAT1=00
[ 4.836373] i2c-adapter i2c-0: Error: no response!
[ 4.836402] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=b0, DAT0=04, DAT1=00
[ 4.836413] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x5c
[ 4.836443] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=b8, DAT0=04, DAT1=00
[ 4.844370] i2c-adapter i2c-0: Error: no response!
[ 4.844399] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=b8, DAT0=04, DAT1=00
[ 4.844437] bus: 'i2c': add driver adt7470
[ 4.844977] i2c-core: driver [adt7470] registered
[ 4.845000] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.845030] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.852373] i2c-adapter i2c-0: Error: no response!
[ 4.852403] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.852413] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.852442] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.860372] i2c-adapter i2c-0: Error: no response!
[ 4.860403] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.860414] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 4.860442] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.868373] i2c-adapter i2c-0: Error: no response!
[ 4.868402] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 4.868444] applesmc: supported laptop not found!
[ 4.868558] applesmc: driver init failed (ret=-19)!
[ 4.868676] bus: 'platform': add driver coretemp
[ 4.869288] bus: 'platform': remove driver coretemp
[ 4.869815] driver: 'coretemp': driver_release
[ 4.869865] bus: 'i2c': add driver dme1737
[ 4.870424] i2c-core: driver [dme1737] registered
[ 4.870450] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.870482] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.876377] i2c-adapter i2c-0: Error: no response!
[ 4.876408] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.876419] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.876449] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.884375] i2c-adapter i2c-0: Error: no response!
[ 4.884404] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.884415] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.884443] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.892376] i2c-adapter i2c-0: Error: no response!
[ 4.892405] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.892433] f71882fg: Not a Fintek device
[ 4.892543] f71882fg: Not a Fintek device
[ 4.892668] bus: 'i2c': add driver f75375
[ 4.893294] i2c-core: driver [f75375] registered
[ 4.893319] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.893350] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.900379] i2c-adapter i2c-0: Error: no response!
[ 4.900409] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.900420] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 4.900448] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.908378] i2c-adapter i2c-0: Error: no response!
[ 4.908407] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 4.908449] bus: 'i2c': add driver fscher
[ 4.908995] i2c-core: driver [fscher] registered
[ 4.909019] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x73
[ 4.909049] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=e6, DAT0=04, DAT1=00
[ 4.916381] i2c-adapter i2c-0: Error: no response!
[ 4.916411] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=e6, DAT0=04, DAT1=00
[ 4.916450] bus: 'i2c': add driver fscpos
[ 4.916989] i2c-core: driver [fscpos] registered
[ 4.917011] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x73
[ 4.917041] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=e6, DAT0=04, DAT1=00
[ 4.924382] i2c-adapter i2c-0: Error: no response!
[ 4.924411] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=e6, DAT0=04, DAT1=00
[ 4.924449] bus: 'i2c': add driver gl520sm
[ 4.924999] i2c-core: driver [gl520sm] registered
[ 4.925022] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 4.925052] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.932383] i2c-adapter i2c-0: Error: no response!
[ 4.932412] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 4.932424] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 4.932452] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.940382] i2c-adapter i2c-0: Error: no response!
[ 4.940410] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 4.940457] hdaps: supported laptop not found!
[ 4.940567] hdaps: driver init failed (ret=-19)!
[ 4.940683] bus: 'platform': add driver i5k_amb
[ 4.941253] Registering platform device 'i5k_amb.0'. Parent at platform
[ 4.941265] device: 'i5k_amb.0': device_add
[ 4.941304] bus: 'platform': add device i5k_amb.0
[ 4.941360] PM: Adding info for platform:i5k_amb.0
[ 4.941906] bus: 'platform': driver_probe_device: matched device i5k_amb.0 with driver i5k_amb
[ 4.941919] bus: 'platform': really_probe: probing driver i5k_amb with device i5k_amb.0
[ 4.942105] bus: 'pci': add driver k8temp
[ 4.942784] bus: 'i2c': add driver lm63
[ 4.943357] i2c-core: driver [lm63] registered
[ 4.943382] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 4.943415] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.948387] i2c-adapter i2c-0: Error: no response!
[ 4.948417] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 4.948462] bus: 'i2c': add driver lm77
[ 4.949063] i2c-core: driver [lm77] registered
[ 4.949088] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x48
[ 4.949120] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.956386] i2c-adapter i2c-0: Error: no response!
[ 4.956415] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 4.956426] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x49
[ 4.956455] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.964385] i2c-adapter i2c-0: Error: no response!
[ 4.964413] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=92, DAT0=04, DAT1=00
[ 4.964424] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4a
[ 4.964453] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.972385] i2c-adapter i2c-0: Error: no response!
[ 4.972415] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=94, DAT0=04, DAT1=00
[ 4.972425] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4b
[ 4.972453] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.980387] i2c-adapter i2c-0: Error: no response!
[ 4.980415] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 4.980489] bus: 'i2c': add driver lm78
[ 4.981041] i2c-core: driver [lm78] registered
[ 4.981065] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x28
[ 4.981097] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.988389] i2c-adapter i2c-0: Error: no response!
[ 4.988419] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 4.988430] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 4.988458] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.996388] i2c-adapter i2c-0: Error: no response!
[ 4.996417] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 4.996428] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 4.996456] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.004423] i2c-adapter i2c-0: Error: no response!
[ 5.004452] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.004463] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 5.004492] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.012390] i2c-adapter i2c-0: Error: no response!
[ 5.012419] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.012430] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 5.012458] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.020391] i2c-adapter i2c-0: Error: no response!
[ 5.020420] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.020431] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 5.020459] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.028392] i2c-adapter i2c-0: Error: no response!
[ 5.028421] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.028432] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.028460] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.036393] i2c-adapter i2c-0: Error: no response!
[ 5.036421] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.036432] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 5.036461] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.044394] i2c-adapter i2c-0: Error: no response!
[ 5.044423] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.044465] bus: 'i2c': add driver lm80
[ 5.045050] i2c-core: driver [lm80] registered
[ 5.045073] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x28
[ 5.045104] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 5.052397] i2c-adapter i2c-0: Error: no response!
[ 5.052427] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=50, DAT0=04, DAT1=00
[ 5.052438] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 5.052466] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.060396] i2c-adapter i2c-0: Error: no response!
[ 5.060425] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.060436] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 5.060464] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.068397] i2c-adapter i2c-0: Error: no response!
[ 5.068426] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.068437] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 5.068465] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.076398] i2c-adapter i2c-0: Error: no response!
[ 5.076427] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.076438] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 5.076466] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.084399] i2c-adapter i2c-0: Error: no response!
[ 5.084428] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.084439] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 5.084467] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.092400] i2c-adapter i2c-0: Error: no response!
[ 5.092429] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.092439] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.092468] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.100401] i2c-adapter i2c-0: Error: no response!
[ 5.100430] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.100441] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 5.100469] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.108402] i2c-adapter i2c-0: Error: no response!
[ 5.108431] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.108471] bus: 'i2c': add driver lm83
[ 5.109020] i2c-core: driver [lm83] registered
[ 5.109043] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x18
[ 5.109073] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.116405] i2c-adapter i2c-0: Error: no response!
[ 5.116435] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.116446] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x19
[ 5.116474] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.124404] i2c-adapter i2c-0: Error: no response!
[ 5.124433] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.124443] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1a
[ 5.124472] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.132405] i2c-adapter i2c-0: Error: no response!
[ 5.132434] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.132444] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 5.132473] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.140406] i2c-adapter i2c-0: Error: no response!
[ 5.140435] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.140445] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 5.140474] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.148407] i2c-adapter i2c-0: Error: no response!
[ 5.148436] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.148446] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 5.148475] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.156408] i2c-adapter i2c-0: Error: no response!
[ 5.156437] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.156447] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 5.156476] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.164409] i2c-adapter i2c-0: Error: no response!
[ 5.164438] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.164448] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4d
[ 5.164476] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.172410] i2c-adapter i2c-0: Error: no response!
[ 5.172438] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.172449] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4e
[ 5.172478] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.180411] i2c-adapter i2c-0: Error: no response!
[ 5.180440] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.180482] bus: 'i2c': add driver lm87
[ 5.181031] i2c-core: driver [lm87] registered
[ 5.181053] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 5.181086] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.188414] i2c-adapter i2c-0: Error: no response!
[ 5.188443] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.188454] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 5.188482] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.196413] i2c-adapter i2c-0: Error: no response!
[ 5.196441] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.196452] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.196480] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.204413] i2c-adapter i2c-0: Error: no response!
[ 5.204443] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.204483] bus: 'i2c': add driver lm90
[ 5.205028] i2c-core: driver [lm90] registered
[ 5.205052] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x18
[ 5.205083] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.212416] i2c-adapter i2c-0: Error: no response!
[ 5.212446] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.212457] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x19
[ 5.212485] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.220416] i2c-adapter i2c-0: Error: no response!
[ 5.220444] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.220455] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1a
[ 5.220483] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.228417] i2c-adapter i2c-0: Error: no response!
[ 5.228445] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.228456] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 5.228484] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.236418] i2c-adapter i2c-0: Error: no response!
[ 5.236446] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.236457] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 5.236485] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.244418] i2c-adapter i2c-0: Error: no response!
[ 5.244447] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.244458] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 5.244486] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.252419] i2c-adapter i2c-0: Error: no response!
[ 5.252448] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.252459] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 5.252487] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.260421] i2c-adapter i2c-0: Error: no response!
[ 5.260449] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.260460] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4d
[ 5.260488] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.268421] i2c-adapter i2c-0: Error: no response!
[ 5.268450] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.268461] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4e
[ 5.268489] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.276422] i2c-adapter i2c-0: Error: no response!
[ 5.276451] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.276493] bus: 'i2c': add driver ltc4245
[ 5.277040] i2c-core: driver [ltc4245] registered
[ 5.277077] bus: 'spi': add driver max1111
[ 5.277624] bus: 'i2c': add driver max1619
[ 5.278174] i2c-core: driver [max1619] registered
[ 5.278198] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x18
[ 5.278231] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.284427] i2c-adapter i2c-0: Error: no response!
[ 5.284458] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=30, DAT0=04, DAT1=00
[ 5.284469] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x19
[ 5.284498] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.292424] i2c-adapter i2c-0: Error: no response!
[ 5.292453] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=32, DAT0=04, DAT1=00
[ 5.292464] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1a
[ 5.292492] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.300425] i2c-adapter i2c-0: Error: no response!
[ 5.300454] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=34, DAT0=04, DAT1=00
[ 5.300465] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x29
[ 5.300493] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.308426] i2c-adapter i2c-0: Error: no response!
[ 5.308455] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=52, DAT0=04, DAT1=00
[ 5.308466] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2a
[ 5.308494] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.316427] i2c-adapter i2c-0: Error: no response!
[ 5.316456] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=54, DAT0=04, DAT1=00
[ 5.316467] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2b
[ 5.316495] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.324428] i2c-adapter i2c-0: Error: no response!
[ 5.324457] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=56, DAT0=04, DAT1=00
[ 5.324468] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4c
[ 5.324496] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.332429] i2c-adapter i2c-0: Error: no response!
[ 5.332457] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=98, DAT0=04, DAT1=00
[ 5.332468] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4d
[ 5.332497] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.340430] i2c-adapter i2c-0: Error: no response!
[ 5.340459] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9a, DAT0=04, DAT1=00
[ 5.340470] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4e
[ 5.340498] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.348432] i2c-adapter i2c-0: Error: no response!
[ 5.348461] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=9c, DAT0=04, DAT1=00
[ 5.348506] bus: 'i2c': add driver max6650
[ 5.349112] i2c-core: driver [max6650] registered
[ 5.349136] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1b
[ 5.349167] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=36, DAT0=04, DAT1=00
[ 5.356443] i2c-adapter i2c-0: Error: no response!
[ 5.356473] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=36, DAT0=04, DAT1=00
[ 5.356484] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x1f
[ 5.356513] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=3e, DAT0=04, DAT1=00
[ 5.360436] usb usb1: suspend_rh (auto-stop)
[ 5.364434] i2c-adapter i2c-0: Error: no response!
[ 5.364463] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=3e, DAT0=04, DAT1=00
[ 5.364473] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x48
[ 5.364502] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 5.372434] i2c-adapter i2c-0: Error: no response!
[ 5.372463] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=90, DAT0=04, DAT1=00
[ 5.372473] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x4b
[ 5.372502] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 5.380435] i2c-adapter i2c-0: Error: no response!
[ 5.380464] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=96, DAT0=04, DAT1=00
[ 5.380488] pc87360: PC8736x not detected, module not inserted.
[ 5.380666] bus: 'pci': add driver sis5595
[ 5.381377] bus: 'i2c': add driver thmc50
[ 5.381923] i2c-core: driver [thmc50] registered
[ 5.381948] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2c
[ 5.381980] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.388438] i2c-adapter i2c-0: Error: no response!
[ 5.388470] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=58, DAT0=04, DAT1=00
[ 5.388481] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2d
[ 5.388510] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.396437] i2c-adapter i2c-0: Error: no response!
[ 5.396466] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5a, DAT0=04, DAT1=00
[ 5.396476] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.396505] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.404438] i2c-adapter i2c-0: Error: no response!
[ 5.404466] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.404525] bus: 'pci': add driver via686a
[ 5.405186] bus: 'pci': add driver vt8231
[ 5.405833] bus: 'i2c': add driver w83l785ts
[ 5.406401] i2c-core: driver [w83l785ts] registered
[ 5.406425] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.406457] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.412441] i2c-adapter i2c-0: Error: no response!
[ 5.412472] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.412516] bus: 'i2c': add driver w83l786ng
[ 5.413108] i2c-core: driver [w83l786ng] registered
[ 5.413131] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2e
[ 5.413162] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.420443] i2c-adapter i2c-0: Error: no response!
[ 5.420472] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5c, DAT0=04, DAT1=00
[ 5.420483] i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x2f
[ 5.420511] i2c-adapter i2c-0: Transaction (pre): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.428441] i2c-adapter i2c-0: Error: no response!
[ 5.428469] i2c-adapter i2c-0: Transaction (post): CNT=00, CMD=11, ADD=5e, DAT0=04, DAT1=00
[ 5.428487] Linux telephony interface: v1.00
[ 5.428620] md: linear personality registered for level -1
[ 5.428727] md: raid1 personality registered for level 1
[ 5.428835] md: raid10 personality registered for level 10
[ 5.496522] raid6: int32x1 233 MB/s
[ 5.564593] raid6: int32x2 224 MB/s
[ 5.632609] raid6: int32x4 203 MB/s
[ 5.700786] raid6: int32x8 188 MB/s
[ 5.768531] raid6: mmxx1 664 MB/s
[ 5.836480] raid6: mmxx2 838 MB/s
[ 5.904578] raid6: sse1x1 560 MB/s
[ 5.972549] raid6: sse1x2 841 MB/s
[ 5.972649] raid6: using algorithm sse1x2 (841 MB/s)
[ 5.972761] md: raid6 personality registered for level 6
[ 5.972864] md: raid5 personality registered for level 5
[ 5.972965] md: raid4 personality registered for level 4
[ 5.973068] md: faulty personality registered for level -5
[ 5.977739] device-mapper: uevent: version 1.0.3
[ 5.979052] device: 'device-mapper': device_add
[ 5.979460] PM: Adding info for No Bus:device-mapper
[ 5.980037] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
[ 5.983813] device-mapper: multipath: version 1.0.5 loaded
[ 5.983943] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.987323] Bluetooth: Virtual HCI driver ver 1.2
[ 5.987463] device: 'vhci': device_add
[ 5.987839] PM: Adding info for No Bus:vhci
[ 5.988482] Bluetooth: HCI UART driver ver 2.2
[ 5.988643] Bluetooth: HCI H4 protocol initialized
[ 5.988749] Bluetooth: HCI BCSP protocol initialized
[ 5.988852] Bluetooth: Broadcom Blutonium firmware driver ver 1.2
[ 5.988976] bus: 'usb': add driver bcm203x
[ 5.989591] usbcore: registered new interface driver bcm203x
[ 5.989727] bus: 'pcmcia': add driver bt3c_cs
[ 5.990272] bus: 'pcmcia': add driver bluecard_cs
[ 5.990798] bus: 'pcmcia': add driver btuart_cs
[ 5.998514] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/none/1.1.2.2
[ 5.998902] PPP BSD Compression module registered
[ 5.999095] dss1_divert module successfully installed
[ 5.999207] HiSax: Linux Driver for passive ISDN cards
[ 5.999309] HiSax: Version 3.5 (kernel)
[ 5.999409] HiSax: Layer1 Revision 2.46.2.5
[ 5.999507] HiSax: Layer2 Revision 2.30.2.4
[ 5.999604] HiSax: TeiMgr Revision 2.20.2.3
[ 5.999701] HiSax: Layer3 Revision 2.22.2.3
[ 5.999800] HiSax: LinkLayer Revision 2.59.2.4
[ 5.999989] HiSax: Total 1 card defined
[ 6.000165] HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
[ 6.000271] Gazel: Driver Revision 2.19.2.4
[ 6.000370] Gazel: ISA PnP card automatic recognition
[ 6.000559] Gazel: Card ISA R647/R648 found
[ 6.000667] Gazel: config irq:15 isac:0x8180 cfg:0xC180
[ 6.000769] Gazel: hscx A:0x180 hscx B:0x4180
[ 6.000904] Gazel: io ports 0x2180-0x2190 already in use
[ 6.001109] HiSax: Card Gazel not installed !
[ 6.001230] bus: 'pcmcia': add driver avma1_cs
[ 6.002165] bus: 'pcmcia': add driver teles_cs
[ 6.002756] hisax_st5481: ST5481 USB ISDN driver $Revision: 2.4.2.3 $
[ 6.002959] bus: 'usb': add driver st5481_usb
[ 6.003604] usbcore: registered new interface driver st5481_usb
[ 6.003805] lguest: mapped switcher at ffc00000
[ 6.003945] device: 'lguest': device_add
[ 6.004332] PM: Adding info for No Bus:lguest
[ 6.005120] bus: 'i2c': add driver pca9532
[ 6.005838] i2c-core: driver [pca9532] registered
[ 6.005872] bus: 'platform': add driver leds-gpio
[ 6.006449] Registering platform device 'dell_rbu'. Parent at platform
[ 6.006460] device: 'dell_rbu': device_add
[ 6.006497] bus: 'platform': add device dell_rbu
[ 6.006554] PM: Adding info for platform:dell_rbu
[ 6.007127] No iBFT detected.
[ 6.007293] bus: 'pci': add driver ioatdma
[ 6.008976] bus: 'hid': registered
[ 6.009000] device class 'hidraw': registering
[ 6.009875] bus: 'hid': add driver a4tech
[ 6.010453] bus: 'hid': add driver apple
[ 6.010988] bus: 'hid': add driver belkin
[ 6.011516] bus: 'hid': add driver cherry
[ 6.012029] bus: 'hid': add driver chicony
[ 6.012608] bus: 'hid': add driver cypress
[ 6.013166] bus: 'hid': add driver ezkey
[ 6.013767] bus: 'hid': add driver gyration
[ 6.014484] bus: 'hid': add driver logitech
[ 6.015059] bus: 'hid': add driver microsoft
[ 6.015595] bus: 'hid': add driver monterey
[ 6.016136] bus: 'hid': add driver ntrig
[ 6.017243] bus: 'hid': add driver pantherlord
[ 6.017855] bus: 'hid': add driver petalynx
[ 6.018401] bus: 'hid': add driver samsung
[ 6.018929] bus: 'hid': add driver sony
[ 6.019450] bus: 'hid': add driver sunplus
[ 6.019965] bus: 'hid': add driver thrustmaster
[ 6.020542] bus: 'hid': add driver topseed
[ 6.021099] bus: 'hid': add driver generic-usb
[ 6.021751] bus: 'usb': add driver hiddev
[ 6.022319] usbcore: registered new interface driver hiddev
[ 6.022466] bus: 'usb': add driver usbhid
[ 6.023168] usbcore: registered new interface driver usbhid
[ 6.023306] usbhid: v2.6:USB HID core driver
[ 6.023424] bus: 'usb': add driver usbmouse
[ 6.024013] usbcore: registered new interface driver usbmouse
[ 6.024136] usbmouse: v1.6:USB HID Boot Protocol mouse driver
[ 6.024255] device: 'virtio-pci': device_add
[ 6.024302] PM: Adding info for No Bus:virtio-pci
[ 6.024369] bus: 'pci': add driver virtio-pci
[ 6.026027] bus: 'virtio': add driver virtio_balloon
[ 6.026611] device class 'sound': registering
[ 6.027367] Advanced Linux Sound Architecture Driver Version 1.0.18a.
[ 6.027553] device: 'timer': device_add
[ 6.027961] PM: Adding info for No Bus:timer
[ 6.030397] bus: 'usb': add driver snd-usb-usx2y
[ 6.031143] usbcore: registered new interface driver snd-usb-usx2y
[ 6.031299] bus: 'usb': add driver snd-usb-us122l
[ 6.031892] usbcore: registered new interface driver snd-usb-us122l
[ 6.032030] bus: 'usb': add driver snd-usb-caiaq
[ 6.032639] usbcore: registered new interface driver snd-usb-caiaq
[ 6.032779] bus: 'pcmcia': add driver snd-vxpocket
[ 6.033336] bus: 'pcmcia': add driver snd-pdaudiocf
[ 6.033868] ALSA device list:
[ 6.033972] No soundcards found.
[ 6.034069] oprofile: using timer interrupt.
[ 6.035169] pktgen v2.70: Packet Generator for packet performance testing.
[ 6.036240] NET: Registered protocol family 26
[ 6.041135] IPv4 over IPv4 tunneling driver
[ 6.041368] device: 'tunl0': device_add
[ 6.041686] PM: Adding info for No Bus:tunl0
[ 6.045256] GRE over IPv4 tunneling driver
[ 6.045441] device: 'gre0': device_add
[ 6.045740] PM: Adding info for No Bus:gre0
[ 6.049889] TCP bic registered
[ 6.050004] TCP westwood registered
[ 6.050101] TCP hybla registered
[ 6.050199] TCP veno registered
[ 6.050296] TCP lp registered
[ 6.050396] NET: Registered protocol family 17
[ 6.050563] NET: Registered protocol family 15
[ 6.050715] bus: 'platform': add driver dsa
[ 6.052407] NET: Registered protocol family 4
[ 6.055001] NET: Registered protocol family 9
[ 6.055115] X.25 for Linux Version 0.2
[ 6.055680] rose0 (): not using net_device_ops yet
[ 6.055792] device: 'rose0': device_add
[ 6.056107] PM: Adding info for No Bus:rose0
[ 6.059873] rose1 (): not using net_device_ops yet
[ 6.059996] device: 'rose1': device_add
[ 6.060296] PM: Adding info for No Bus:rose1
[ 6.064054] rose2 (): not using net_device_ops yet
[ 6.064172] device: 'rose2': device_add
[ 6.064471] PM: Adding info for No Bus:rose2
[ 6.068326] rose3 (): not using net_device_ops yet
[ 6.068449] device: 'rose3': device_add
[ 6.068831] PM: Adding info for No Bus:rose3
[ 6.072761] rose4 (): not using net_device_ops yet
[ 6.072878] device: 'rose4': device_add
[ 6.073186] PM: Adding info for No Bus:rose4
[ 6.077322] rose5 (): not using net_device_ops yet
[ 6.077442] device: 'rose5': device_add
[ 6.077756] PM: Adding info for No Bus:rose5
[ 6.081759] rose6 (): not using net_device_ops yet
[ 6.081874] device: 'rose6': device_add
[ 6.082180] PM: Adding info for No Bus:rose6
[ 6.086482] rose7 (): not using net_device_ops yet
[ 6.086603] device: 'rose7': device_add
[ 6.086924] PM: Adding info for No Bus:rose7
[ 6.091131] rose8 (): not using net_device_ops yet
[ 6.091247] device: 'rose8': device_add
[ 6.091613] PM: Adding info for No Bus:rose8
[ 6.096048] rose9 (): not using net_device_ops yet
[ 6.096169] device: 'rose9': device_add
[ 6.096549] PM: Adding info for No Bus:rose9
[ 6.100869] NET: Registered protocol family 11
[ 6.101843] NET: Registered protocol family 3
[ 6.102115] Bluetooth: L2CAP ver 2.11
[ 6.102213] Bluetooth: L2CAP socket layer initialized
[ 6.102323] Bluetooth: SCO (Voice Link) ver 0.6
[ 6.102425] Bluetooth: SCO socket layer initialized
[ 6.102776] Bluetooth: RFCOMM socket layer initialized
[ 6.102971] Bluetooth: RFCOMM TTY layer initialized
[ 6.103075] Bluetooth: RFCOMM ver 1.10
[ 6.103173] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.103277] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 6.103393] bus: 'hid': add driver generic-bluetooth
[ 6.104193] lec.c: Jan 10 2009 13:34:55 initialized
[ 6.104304] NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
[ 6.109471] DECnet: Routing cache hash table of 1024 buckets, 32Kbytes
[ 6.110735] NET: Registered protocol family 12
[ 6.111920] NET: Registered protocol family 19
[ 6.112113] NET: Registered protocol family 35
[ 6.114539] 802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
[ 6.114665] All bugs added by David S. Miller <[email protected]>
[ 6.126982] CCID: Activated CCID 2 (TCP-like)
[ 6.129391] CCID: Activated CCID 3 (TCP-Friendly Rate Control)
[ 6.136755] SCTP: Hash tables configured (established 4096 bind 4096)
[ 6.140904] sctp_init_sock(sk: deb74000)
[ 6.140998] TIPC: Activated (version 1.6.4 compiled Jan 10 2009 13:41:46)
[ 6.145443] NET: Registered protocol family 30
[ 6.145570] TIPC: Started in single node mode
[ 6.145682] IO APIC resources could be not be allocated.
[ 6.145821] Using IPI No-Shortcut mode
[ 6.145965] device: 'cpu_dma_latency': device_add
[ 6.146368] PM: Adding info for No Bus:cpu_dma_latency
[ 6.147029] device: 'network_latency': device_add
[ 6.147278] PM: Adding info for No Bus:network_latency
[ 6.147929] device: 'network_throughput': device_add
[ 6.148149] PM: Adding info for No Bus:network_throughput
[ 6.149412] Magic number: 9:883:836
[ 6.149744] tty ptyu2: hash matches
[ 6.149909] saa7134 ALSA driver for DMA sound loaded
[ 6.150010] saa7134 ALSA: no saa7134 cards found
[ 6.150132] rtc-test rtc-test.0: setting system clock to 2009-01-10 13:51:01 UTC (1231595461)
[ 6.150295] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 6.150400] EDD information not available.
[ 6.154149] Freeing unused kernel memory: 628k freed
[ 6.154665] device: 'vcs1': device_add
[ 6.155077] PM: Adding info for No Bus:vcs1
[ 6.155967] device: 'vcsa1': device_add
[ 6.156252] PM: Adding info for No Bus:vcsa1
[ 6.816669] hub 1-0:1.0: hub_suspend
[ 6.816722] usb usb1: bus auto-suspend
[ 6.816732] usb usb1: suspend_rh
[ 13.182179] kjournald starting. Commit interval 5 seconds
[ 13.182361] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.065135] device: 'vcs1': device_unregister
[ 14.065155] PM: Removing info for No Bus:vcs1
[ 14.065728] device: 'vcs1': device_create_release
[ 14.065750] device: 'vcsa1': device_unregister
[ 14.065756] PM: Removing info for No Bus:vcsa1
[ 14.065977] device: 'vcsa1': device_create_release
[ 14.066290] device: 'vcs1': device_add
[ 14.066487] PM: Adding info for No Bus:vcs1
[ 14.066615] device: 'vcsa1': device_add
[ 14.066717] PM: Adding info for No Bus:vcsa1
[ 16.310572] awk used greatest stack depth: 1456 bytes left
[ 22.209247] usb usb1: uevent
[ 22.209484] usb 1-0:1.0: uevent
[ 35.579758] EXT3 FS on sda1, internal journal
[ 37.635481] Adding 1050832k swap on /dev/sda2. Priority:-1 extents:1 across:1050832k
[ 50.638920] warning: `dbus-daemon' uses deprecated v2 capabilities in a way that may be insecure.
[ 51.936510] usb usb1: usb auto-resume
[ 51.936538] usb usb1: wakeup_rh
[ 51.974084] hub 1-0:1.0: hub_resume
[ 51.974675] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 52.982253] usb usb1: suspend_rh (auto-stop)
[ 53.284792] ip used greatest stack depth: 1452 bytes left
[ 54.822448] hub 1-0:1.0: hub_suspend
[ 54.822500] usb usb1: bus auto-suspend
[ 54.822511] usb usb1: suspend_rh
[ 61.697271] cupsd used greatest stack depth: 1140 bytes left
[ 62.866975] eth0: setting full-duplex.
[ 62.869327] bpq0 (): not using net_device_ops yet
[ 62.869356] device: 'bpq0': device_add
[ 62.869706] PM: Adding info for No Bus:bpq0
[ 68.611483] device: 'vcs6': device_add
[ 68.611923] PM: Adding info for No Bus:vcs6
[ 68.612225] device: 'vcsa6': device_add
[ 68.612351] PM: Adding info for No Bus:vcsa6
[ 68.616430] device: 'vcs5': device_add
[ 68.616860] PM: Adding info for No Bus:vcs5
[ 68.617029] device: 'vcsa5': device_add
[ 68.617141] PM: Adding info for No Bus:vcsa5
[ 68.639552] device: 'vcs2': device_add
[ 68.639993] PM: Adding info for No Bus:vcs2
[ 68.640246] device: 'vcsa2': device_add
[ 68.640413] PM: Adding info for No Bus:vcsa2
[ 68.653426] device: 'vcs3': device_add
[ 68.653864] PM: Adding info for No Bus:vcs3
[ 68.654029] device: 'vcsa3': device_add
[ 68.654139] PM: Adding info for No Bus:vcsa3
[ 68.655526] device: 'vcs3': device_unregister
[ 68.655541] PM: Removing info for No Bus:vcs3
[ 68.656135] device: 'vcs3': device_create_release
[ 68.656163] device: 'vcsa3': device_unregister
[ 68.656169] PM: Removing info for No Bus:vcsa3
[ 68.656419] device: 'vcsa3': device_create_release
[ 68.667758] device: 'vcs4': device_add
[ 68.668349] PM: Adding info for No Bus:vcs4
[ 68.668546] device: 'vcsa4': device_add
[ 68.668678] PM: Adding info for No Bus:vcsa4
[ 68.670974] device: 'vcs4': device_unregister
[ 68.670988] PM: Removing info for No Bus:vcs4
[ 68.671477] device: 'vcs4': device_create_release
[ 68.671505] device: 'vcsa4': device_unregister
[ 68.671511] PM: Removing info for No Bus:vcsa4
[ 68.671753] device: 'vcsa4': device_create_release
[ 68.672015] device: 'vcs4': device_add
[ 68.672314] PM: Adding info for No Bus:vcs4
[ 68.672439] device: 'vcsa4': device_add
[ 68.672548] PM: Adding info for No Bus:vcsa4
[ 68.700480] device: 'vcs6': device_unregister
[ 68.700500] PM: Removing info for No Bus:vcs6
[ 68.701073] device: 'vcs6': device_create_release
[ 68.701099] device: 'vcsa6': device_unregister
[ 68.701105] PM: Removing info for No Bus:vcsa6
[ 68.701331] device: 'vcsa6': device_create_release
[ 68.701627] device: 'vcs6': device_add
[ 68.701836] PM: Adding info for No Bus:vcs6
[ 68.701961] device: 'vcsa6': device_add
[ 68.702073] PM: Adding info for No Bus:vcsa6
[ 68.705938] device: 'vcs5': device_unregister
[ 68.705956] PM: Removing info for No Bus:vcs5
[ 68.706504] device: 'vcs5': device_create_release
[ 68.706528] device: 'vcsa5': device_unregister
[ 68.706534] PM: Removing info for No Bus:vcsa5
[ 68.706767] device: 'vcsa5': device_create_release
[ 68.707009] device: 'vcs5': device_add
[ 68.707213] PM: Adding info for No Bus:vcs5
[ 68.707336] device: 'vcsa5': device_add
[ 68.707448] PM: Adding info for No Bus:vcsa5
[ 68.712359] device: 'vcs2': device_unregister
[ 68.712373] PM: Removing info for No Bus:vcs2
[ 68.712925] device: 'vcs2': device_create_release
[ 68.712948] device: 'vcsa2': device_unregister
[ 68.712954] PM: Removing info for No Bus:vcsa2
[ 68.713180] device: 'vcsa2': device_create_release
[ 68.713443] device: 'vcs3': device_add
[ 68.713653] PM: Adding info for No Bus:vcs3
[ 68.713815] device: 'vcsa3': device_add
[ 68.713937] PM: Adding info for No Bus:vcsa3
[ 68.714186] device: 'vcs2': device_add
[ 68.714326] PM: Adding info for No Bus:vcs2
[ 68.714463] device: 'vcsa2': device_add
[ 68.714577] PM: Adding info for No Bus:vcsa2
[ 70.955151] device: 'vcs7': device_add
[ 70.955592] PM: Adding info for No Bus:vcs7
[ 70.955782] device: 'vcsa7': device_add
[ 70.955934] PM: Adding info for No Bus:vcsa7
[ 75.561985] evbug.c: Event. Dev: input2, Type: 20, Code: 0, Value: 500
Ingo Molnar wrote:
> 871af12: libata: Add 32bit PIO support
What happens when you back this out?
Jeff
Christian Borntraeger wrote:
> Am Samstag 10 Januar 2009 schrieb Alan Cox:
>>> That's the typical REQUEST SENSE command with 18-byte data length.
>> Which means something has become horribly broken in the core libata stack.
>> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
>> would therefore not trigger the WARN_ON. Someone has passed an sg list
>> that isn't properly terminated perhaps ?
>>
>> I wonder if the pad code broke this.
>
> I just checked 2.6.28 + PIO32 patch. Its also broken. Whatever caused this
> problem did it a while ago.
Just to be clear, you mean:
2.6.28 is OK
2.6.28 + PIO32 is broken
Correct?
Jeff
* Jeff Garzik <[email protected]> wrote:
> Ingo Molnar wrote:
>> 871af12: libata: Add 32bit PIO support
>
> What happens when you back this out?
yep, that's the one that looked most suspect to me too so i already
reverted it in tip/out-of-tree.
But in the normal tip/master test cycle the box takes about 50 minutes to
build its random kernel and reboot into it (800 MHz P3), so i started a
full automated bisection instead driven from a faster box.
The bug triggers deterministically so whatever leads to it, we should have
it within ~20 minutes with a bit of luck (== there's no other bug in the
bisection run that makes bisection more difficult).
The current bisection state is:
# bad: [9a100a44] Merge git://git.kernel.org/pub/scm/linux/kernel/gi
# good: [9e42d0cf] Merge git://git.kernel.org/pub/scm/linux/kernel/gi
# good: [e441d54d] Btrfs: add permission checks to the ioctls
# bad: [cd764695] Merge git://git.kernel.org/pub/scm/linux/kernel/gi
# bad: [a419df8a] Merge branch 'upstream-linus' of git://git.kernel.
# good: [61bce0f1] pid: generalize task_active_pid_ns
and "871af12: libata: Add 32bit PIO support" is still in the bisection
window.
Ingo
Am Samstag 10 Januar 2009 schrieb Jeff Garzik:
> Christian Borntraeger wrote:
> > Am Samstag 10 Januar 2009 schrieb Alan Cox:
> >>> That's the typical REQUEST SENSE command with 18-byte data length.
> >> Which means something has become horribly broken in the core libata
stack.
> >> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
> >> would therefore not trigger the WARN_ON. Someone has passed an sg list
> >> that isn't properly terminated perhaps ?
> >>
> >> I wonder if the pad code broke this.
> >
> > I just checked 2.6.28 + PIO32 patch. Its also broken. Whatever caused this
> > problem did it a while ago.
>
> Just to be clear, you mean:
>
> 2.6.28 is OK
> 2.6.28 + PIO32 is broken
>
> Correct?
Yes.
* Ingo Molnar <[email protected]> wrote:
> build its random kernel and reboot into it (800 MHz P3), so i started a
> full automated bisection instead driven from a faster box.
and the winner is:
| 871af1210f13966ab911ed2166e4ab2ce775b99d is first bad commit
| commit 871af1210f13966ab911ed2166e4ab2ce775b99d
| Author: Alan Cox <[email protected]>
| Date: Mon Jan 5 14:16:39 2009 +0000
|
| libata: Add 32bit PIO support
And the revert below does the trick.
Ingo
--------------------->
>From f1d26da598230cc050ee2c7890bd3cebd2e76e27 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <[email protected]>
Date: Sat, 10 Jan 2009 14:04:57 +0100
Subject: [PATCH] Revert "libata: Add 32bit PIO support"
This reverts commit 871af1210f13966ab911ed2166e4ab2ce775b99d.
[ 3.834413] PM: Adding info for No Bus:8:0
[ 3.835116] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.835237] driver: '0:0:0:0': driver_bound: bound to device 'sd'
[ 3.835249] bus: 'scsi': really_probe: bound device 0:0:0:0 to driver sd
[ 3.835272] device: '0:0:0:0': device_add
[ 3.835374] PM: Adding info for No Bus:0:0:0:0
[ 4.112738] ata2.00: ATAPI: QSI DVD-ROM SDR-081, EHA8, max UDMA/33
[ 4.120617] ata2.00: configured for UDMA/33
[ 4.121275] ------------[ cut here ]------------
[ 4.121380] WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x3d9/0x840()
[ 4.121538] Hardware name: HP OmniBook PC
[ 4.121644] Pid: 0, comm: swapper Not tainted 2.6.28-tip-10029-g20e9954-dirty #3
[ 4.121798] Call Trace:
[ 4.121912] [<c013d006>] warn_slowpath+0x86/0xa0
[ 4.122030] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122136] [<c0133270>] ? default_wake_function+0x10/0x20
[ 4.122260] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.122368] [<c012c5ee>] ? complete+0x4e/0x60
[ 4.122490] [<c06513d3>] ? ata_qc_complete_internal+0x13/0x20
[ 4.122602] [<c064f6ed>] ? __ata_qc_complete+0x6d/0xe0
[ 4.122710] [<c065e0a9>] ? ata_sff_qc_fill_rtf+0x19/0x30
[ 4.122817] [<c065fa07>] ? ata_sff_data_xfer32+0x77/0xd0
[ 4.122923] [<c0660739>] ata_sff_hsm_move+0x3d9/0x840
[ 4.123029] [<c034eb06>] ? _raw_spin_lock+0x46/0x170
[ 4.123134] [<c0660ef9>] ata_sff_interrupt+0x129/0x1e0
[ 4.123246] [<c0171dc0>] handle_IRQ_event+0x30/0x70
[ 4.123354] [<c0173b05>] handle_level_irq+0x75/0xe0
[ 4.123459] [<c0173a90>] ? handle_level_irq+0x0/0xe0
[ 4.123562] <IRQ> [<c0104607>] ? common_interrupt+0x27/0x2c
[ 4.123725] [<c0120120>] ? native_safe_halt+0x0/0x10
[ 4.123830] [<c012012a>] ? native_safe_halt+0xa/0x10
[ 4.123942] [<c010aaf9>] ? default_idle+0x69/0xa0
[ 4.124053] [<c015f792>] ? tick_nohz_restart_sched_tick+0x32/0x1b0
[ 4.124167] [<c011715f>] ? apm_cpu_idle+0xdf/0x260
[ 4.124273] [<c01027d8>] ? cpu_idle+0x78/0x100
[ 4.124379] [<c034e9bd>] ? _raw_spin_unlock+0x5d/0xa0
[ 4.124490] [<c09a92b3>] ? rest_init+0x53/0x60
[ 4.124601] [<c0e4d82a>] ? start_kernel+0x2ba/0x360
[ 4.124709] [<c0e4d260>] ? unknown_bootoption+0x0/0x210
[ 4.124820] [<c0e4d07c>] ? i386_start_kernel+0x7c/0xb0
[ 4.124948] ---[ end trace 83f9033b42a87df9 ]---
[ 4.126783] scsi 1:0:0:0: CD-ROM QSI DVD-ROM SDR-081 EHA8 PQ: 0 ANSI: 5
[ 4.126979] device: 'target1:0:0': device_add
[ 4.127040] PM: Adding info for No Bus:target1:0:0
[ 4.127057] device: '1:0:0:0': device_add
[ 4.127191] bus: 'scsi': add device 1:0:0:0
[ 4.127235] PM: Adding info for scsi:1:0:0:0
[ 4.127994] bus: 'scsi': driver_probe_device: matched device 1:0:0:0 with driver osst
---
drivers/ata/ata_piix.c | 2 +-
drivers/ata/libata-sff.c | 53 ---------------------------------------------
drivers/ata/pata_ali.c | 6 ++--
drivers/ata/pata_amd.c | 4 +-
drivers/ata/pata_mpiix.c | 3 +-
drivers/ata/pata_sil680.c | 4 +-
include/linux/libata.h | 3 --
7 files changed, 9 insertions(+), 66 deletions(-)
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 887d8f4..7865954 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -310,7 +310,7 @@ static struct scsi_host_template piix_sht = {
};
static struct ata_port_operations piix_pata_ops = {
- .inherits = &ata_bmdma32_port_ops,
+ .inherits = &ata_bmdma_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = piix_set_piomode,
.set_dmamode = piix_set_dmamode,
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 0eae9b4..e7c8514 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -80,13 +80,6 @@ const struct ata_port_operations ata_bmdma_port_ops = {
};
EXPORT_SYMBOL_GPL(ata_bmdma_port_ops);
-const struct ata_port_operations ata_bmdma32_port_ops = {
- .inherits = &ata_bmdma_port_ops,
-
- .sff_data_xfer = ata_sff_data_xfer32,
-};
-EXPORT_SYMBOL_GPL(ata_bmdma32_port_ops);
-
/**
* ata_fill_sg - Fill PCI IDE PRD table
* @qc: Metadata associated with taskfile to be transferred
@@ -743,52 +736,6 @@ unsigned int ata_sff_data_xfer(struct ata_device *dev, unsigned char *buf,
EXPORT_SYMBOL_GPL(ata_sff_data_xfer);
/**
- * ata_sff_data_xfer32 - Transfer data by PIO
- * @dev: device to target
- * @buf: data buffer
- * @buflen: buffer length
- * @rw: read/write
- *
- * Transfer data from/to the device data register by PIO using 32bit
- * I/O operations.
- *
- * LOCKING:
- * Inherited from caller.
- *
- * RETURNS:
- * Bytes consumed.
- */
-
-unsigned int ata_sff_data_xfer32(struct ata_device *dev, unsigned char *buf,
- unsigned int buflen, int rw)
-{
- struct ata_port *ap = dev->link->ap;
- void __iomem *data_addr = ap->ioaddr.data_addr;
- unsigned int words = buflen >> 2;
- int slop = buflen & 3;
-
- /* Transfer multiple of 4 bytes */
- if (rw == READ)
- ioread32_rep(data_addr, buf, words);
- else
- iowrite32_rep(data_addr, buf, words);
-
- if (unlikely(slop)) {
- __le32 pad;
- if (rw == READ) {
- pad = cpu_to_le32(ioread32(ap->ioaddr.data_addr));
- memcpy(buf + buflen - slop, &pad, slop);
- } else {
- memcpy(&pad, buf + buflen - slop, slop);
- iowrite32(le32_to_cpu(pad), ap->ioaddr.data_addr);
- }
- words++;
- }
- return words << 2;
-}
-EXPORT_SYMBOL_GPL(ata_sff_data_xfer32);
-
-/**
* ata_sff_data_xfer_noirq - Transfer data by PIO
* @dev: device to target
* @buf: data buffer
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index a7999c1..a4f9e39 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -151,7 +151,8 @@ static void ali_fifo_control(struct ata_port *ap, struct ata_device *adev, int o
pci_read_config_byte(pdev, pio_fifo, &fifo);
fifo &= ~(0x0F << shift);
- fifo |= (on << shift);
+ if (on)
+ fifo |= (on << shift);
pci_write_config_byte(pdev, pio_fifo, fifo);
}
@@ -369,11 +370,10 @@ static struct ata_port_operations ali_early_port_ops = {
.inherits = &ata_sff_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = ali_set_piomode,
- .sff_data_xfer = ata_sff_data_xfer32,
};
static const struct ata_port_operations ali_dma_base_ops = {
- .inherits = &ata_bmdma32_port_ops,
+ .inherits = &ata_bmdma_port_ops,
.set_piomode = ali_set_piomode,
.set_dmamode = ali_set_dmamode,
};
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 63719ab..0ec9c7d 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_amd"
-#define DRV_VERSION "0.3.11"
+#define DRV_VERSION "0.3.10"
/**
* timing_setup - shared timing computation and load
@@ -345,7 +345,7 @@ static struct scsi_host_template amd_sht = {
};
static const struct ata_port_operations amd_base_port_ops = {
- .inherits = &ata_bmdma32_port_ops,
+ .inherits = &ata_bmdma_port_ops,
.prereset = amd_pre_reset,
};
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index aa576ca..7c8faa4 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -35,7 +35,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_mpiix"
-#define DRV_VERSION "0.7.7"
+#define DRV_VERSION "0.7.6"
enum {
IDETIM = 0x6C, /* IDE control register */
@@ -146,7 +146,6 @@ static struct ata_port_operations mpiix_port_ops = {
.cable_detect = ata_cable_40wire,
.set_piomode = mpiix_set_piomode,
.prereset = mpiix_pre_reset,
- .sff_data_xfer = ata_sff_data_xfer32,
};
static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 9e764e5..83580a5 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -32,7 +32,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_sil680"
-#define DRV_VERSION "0.4.9"
+#define DRV_VERSION "0.4.8"
#define SIL680_MMIO_BAR 5
@@ -195,7 +195,7 @@ static struct scsi_host_template sil680_sht = {
};
static struct ata_port_operations sil680_port_ops = {
- .inherits = &ata_bmdma32_port_ops,
+ .inherits = &ata_bmdma_port_ops,
.cable_detect = sil680_cable_detect,
.set_piomode = sil680_set_piomode,
.set_dmamode = sil680_set_dmamode,
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 4f7c8fb..3449de5 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1518,7 +1518,6 @@ extern void sata_pmp_error_handler(struct ata_port *ap);
extern const struct ata_port_operations ata_sff_port_ops;
extern const struct ata_port_operations ata_bmdma_port_ops;
-extern const struct ata_port_operations ata_bmdma32_port_ops;
/* PIO only, sg_tablesize and dma_boundary limits can be removed */
#define ATA_PIO_SHT(drv_name) \
@@ -1546,8 +1545,6 @@ extern void ata_sff_exec_command(struct ata_port *ap,
const struct ata_taskfile *tf);
extern unsigned int ata_sff_data_xfer(struct ata_device *dev,
unsigned char *buf, unsigned int buflen, int rw);
-extern unsigned int ata_sff_data_xfer32(struct ata_device *dev,
- unsigned char *buf, unsigned int buflen, int rw);
extern unsigned int ata_sff_data_xfer_noirq(struct ata_device *dev,
unsigned char *buf, unsigned int buflen, int rw);
extern u8 ata_sff_irq_on(struct ata_port *ap);
On Sat, 10 Jan 2009 08:14:01 -0500
Jeff Garzik <[email protected]> wrote:
> Christian Borntraeger wrote:
> > Am Samstag 10 Januar 2009 schrieb Alan Cox:
> >>> That's the typical REQUEST SENSE command with 18-byte data length.
> >> Which means something has become horribly broken in the core libata stack.
> >> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
> >> would therefore not trigger the WARN_ON. Someone has passed an sg list
> >> that isn't properly terminated perhaps ?
> >>
> >> I wonder if the pad code broke this.
> >
> > I just checked 2.6.28 + PIO32 patch. Its also broken. Whatever caused this
> > problem did it a while ago.
>
> Just to be clear, you mean:
>
> 2.6.28 is OK
> 2.6.28 + PIO32 is broken
As far as I can tell
2.6.28 is broken but it doesn't show due to other factors
2.6.28 using 32bit PIO shows up the fact someone seems to be passing
broken sg lists
On Sat, 10 Jan 2009 16:01:44 +0300
Sergei Shtylyov <[email protected]> wrote:
> Hello.
>
> Alan Cox wrote:
>
> >> That's the typical REQUEST SENSE command with 18-byte data length.
>
> > Which means something has become horribly broken in the core libata stack.
> > An 18 byte inquiry would have 18 bytes as the *last* sg element. That
>
> Did you get me right? 18 bytes is the typical REQUEST SENSE payload
> (libata requested 96 bytes), not INQUIRY. For the INQUIRY 36 bytes was
> requested and received (divisible by 4).
> And I doubt there can be more than one S/G segment with such lengths...
I am quite sure there cannot be - however the WARN clearly shows that we
got passed one.
On Sat, 10 Jan 2009 14:36:17 +0100
Ingo Molnar <[email protected]> wrote:
>
> * Ingo Molnar <[email protected]> wrote:
>
> > build its random kernel and reboot into it (800 MHz P3), so i started a
> > full automated bisection instead driven from a faster box.
>
> and the winner is:
>
> | 871af1210f13966ab911ed2166e4ab2ce775b99d is first bad commit
> | commit 871af1210f13966ab911ed2166e4ab2ce775b99d
> | Author: Alan Cox <[email protected]>
> | Date: Mon Jan 5 14:16:39 2009 +0000
> |
> | libata: Add 32bit PIO support
>
> And the revert below does the trick.
Unfortunately it only hides the bug - that code doesn't change the sg
lists being passed, it just catches out anyone who pasts a non divisble
by four malformed sg list.
The real bug is still there
> > That would therefore not trigger the WARN_ON. Someone has passed an sg
> > list that isn't properly terminated perhaps ?
> >
> > I wonder if the pad code broke this.
>
> note, one of my testboxes in the -tip testing hw pool (an older HP laptop)
> started triggering this too today:
No suprise - the traces I've got seem to indicate a bogus sg list from
the core libata code. If so its general and the 32bit pio is just showing
it up.
Am Samstag 10 Januar 2009 schrieb Ingo Molnar:
>
> * Ingo Molnar <[email protected]> wrote:
>
> > build its random kernel and reboot into it (800 MHz P3), so i started a
> > full automated bisection instead driven from a faster box.
>
> and the winner is:
>
> | 871af1210f13966ab911ed2166e4ab2ce775b99d is first bad commit
> | commit 871af1210f13966ab911ed2166e4ab2ce775b99d
> | Author: Alan Cox <[email protected]>
> | Date: Mon Jan 5 14:16:39 2009 +0000
> |
> | libata: Add 32bit PIO support
Yes, thats what I send Alan yesterday. We currently try to understand why it
fails.
On Sat, 2009-01-10 at 12:21 +0000, Alan Cox wrote:
> > That's the typical REQUEST SENSE command with 18-byte data length.
>
> Which means something has become horribly broken in the core libata stack.
> An 18 byte inquiry would have 18 bytes as the *last* sg element. That
> would therefore not trigger the WARN_ON. Someone has passed an sg list
> that isn't properly terminated perhaps ?
>
> I wonder if the pad code broke this.
I don't think it's anything to do with padding or the block layer.
I think we sent out a request sense with 96 bytes of space for a reply,
which is bog standard for SCSI. The device sent back a payload of 18
bytes, which is perfectly legal ... request sense is a variable payload
command, the device doesn't have to fill the buffer we give it.
18, by the way, is the typical reply length for non descriptor sense
format with no additional information, so this is really expected
behaviour.
Your problem is that the *device* is wanting to transfer a set of bytes
not divisible by four. If you want to use word based PIO, you'll have
to fall back to collecting bytes for the last two. Alternatively, you
could just do byte PIO for all reply lengths like this ... they occur
all over the SCSI standard, but not usually in critical paths.
James
James Bottomley wrote:
> Your problem is that the *device* is wanting to transfer a set of bytes
> not divisible by four.
That's my initial guess, too...
Jeff
Alan Cox wrote:
>>* Ingo Molnar <[email protected]> wrote:
>>>build its random kernel and reboot into it (800 MHz P3), so i started a
>>>full automated bisection instead driven from a faster box.
>>and the winner is:
>>| 871af1210f13966ab911ed2166e4ab2ce775b99d is first bad commit
>>| commit 871af1210f13966ab911ed2166e4ab2ce775b99d
>>| Author: Alan Cox <[email protected]>
>>| Date: Mon Jan 5 14:16:39 2009 +0000
>>|
>>| libata: Add 32bit PIO support
>>
>>And the revert below does the trick.
> Unfortunately it only hides the bug - that code doesn't change the sg
> lists being passed, it just catches out anyone who pasts a non divisble
> by four malformed sg list.
All the S/G counts printed out were divisible by 4 (36 for INQUIRY and 96
for REQUSET SENSE). It's the *actual* byte count for the REQUEST SENSE that's
no divisible. The SCSI/ATAPI devices are free to sent less data than requested
on non block transfer commands.
MBR, Sergei
O> Your problem is that the *device* is wanting to transfer a set of bytes
> not divisible by four. If you want to use word based PIO, you'll have
> to fall back to collecting bytes for the last two. Alternatively, you
Nope.. you can't do that with ATA block transfers - it isn't the same as
SCSI
> could just do byte PIO for all reply lengths like this ... they occur
> all over the SCSI standard, but not usually in critical paths.
The problem we have is that the sg list the drivers were given had a
segment which was not divisible in length by four and was *NOT* the last
segment in the sg list
The logic in the ATA PIO code is basically
for each sg entry
compute the number of bytes to transfer staying within
the page
transfer that many bytes (but may be more)
if and only if the transfer is NOT the last segment but is
more than the bytes requested - WARN
The block alignment is set to 4 bytes so the block code should be handing
down stuff which is safe. Some of the sense and other stuff is "adjusted"
by the libata-scsi conversion code which at this point I suspect is the
offender.
This is why libata uses the pad buffers we don't get to be quite so exact
about transfer sizes as SCSI is.
Alan
On Sat, 2009-01-10 at 15:12 +0000, Alan Cox wrote:
> O> Your problem is that the *device* is wanting to transfer a set of bytes
> > not divisible by four. If you want to use word based PIO, you'll have
> > to fall back to collecting bytes for the last two. Alternatively, you
>
> Nope.. you can't do that with ATA block transfers - it isn't the same as
> SCSI
Well, in that case you'll have to do byte PIO for all ATAPI devices,
because this is an expected device to host transfer length.
> > could just do byte PIO for all reply lengths like this ... they occur
> > all over the SCSI standard, but not usually in critical paths.
>
> The problem we have is that the sg list the drivers were given had a
> segment which was not divisible in length by four and was *NOT* the last
> segment in the sg list
Yes it was, look at the debugging info:
Christian Borntraeger wrote:
> [ 1.499843] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM
> GSA-U10N 1.05 PQ: 0 ANSI: 5
> [ 1.508389] count: 18 sg->length: 96 qc->cursg_ofs: 0 bytes: 18
> [ 1.509369] qc->cdb[]:03000000600000000000000000000000
> That one is broken.
That's a single element sg list with a 96 byte buffer. That's precisely
what SCSI sets up to receive incoming sense data. There's basically no
setup commands which are multiple element because the sg list is set up
on a kmalloc'd buffer.
The problem is that bytes is 18 and that comes from this:
ap->ops->sff_tf_read(ap, &qc->result_tf);
ireason = qc->result_tf.nsect;
bc_lo = qc->result_tf.lbam;
bc_hi = qc->result_tf.lbah;
bytes = (bc_hi << 8) | bc_lo;
So we're asking the device how much data it wants to transfer. It said
18 bytes. There's nothing padding or aligning in block can do about
this.
> The logic in the ATA PIO code is basically
>
>
> for each sg entry
>
> compute the number of bytes to transfer staying within
> the page
> transfer that many bytes (but may be more)
>
> if and only if the transfer is NOT the last segment but is
> more than the bytes requested - WARN
>
>
> The block alignment is set to 4 bytes so the block code should be handing
> down stuff which is safe. Some of the sense and other stuff is "adjusted"
> by the libata-scsi conversion code which at this point I suspect is the
> offender.
It is. The receive buffer is 96 bytes. It will be page aligned and 96
is divisible by 4.
> This is why libata uses the pad buffers we don't get to be quite so exact
> about transfer sizes as SCSI is.
The block layer does do pad buffers, but in this case there was no need
of one.
James
Alan Cox wrote:
> O> Your problem is that the *device* is wanting to transfer a set of bytes
>>not divisible by four. If you want to use word based PIO, you'll have
>>to fall back to collecting bytes for the last two. Alternatively, you
> Nope.. you can't do that with ATA block transfers - it isn't the same as
> SCSI
ATA block transfers are always mutliple of 512 bytes (except read/write
long), so this shouldn't be an issue... unless the code is trying to split a
sector between 2 pages on an arbitrary boundary -- in this case, even if the
both resulting byte counts divide by 2, you may be busted because of prefetch
that (as the Intel docs say), should have the initial (start of sector) and
all subsequent reads of the same size (either 16- or 32-bit). I don't know if
this situation is actually possible with libata -- but beware...
>>could just do byte PIO for all reply lengths like this ... they occur
>>all over the SCSI standard, but not usually in critical paths.
> The problem we have is that the sg list the drivers were given had a
> segment which was not divisible in length by four and was *NOT* the last
> segment in the sg list
> The logic in the ATA PIO code is basically
> for each sg entry
> compute the number of bytes to transfer staying within
> the page
> transfer that many bytes (but may be more)
>
> if and only if the transfer is NOT the last segment but is
> more than the bytes requested - WARN
The ATAPI logic is more complex since it has to take into account the
arbitrary byte count that a device want to transfer on each INTRQ (read from
the byte count low/high regs).
> Alan
MBR, Sergei
> All the S/G counts printed out were divisible by 4 (36 for INQUIRY and 96
> for REQUSET SENSE). It's the *actual* byte count for the REQUEST SENSE that's
> no divisible. The SCSI/ATAPI devices are free to sent less data than requested
> on non block transfer commands.
That is just fine - if the sg list is not corrupt or being mishandled and
the atapi pio code is not buggy.
RTFS a bit and it becomes obvious that the core libata code has a bug:
>From libata-sff.c:
/* consumed can be larger than count only for the last transfer */
WARN_ON_ONCE(qc->cursg && count != consumed);
The big clue turns out to be that the code doesn't match the comment.
Next note the check on qc->cursg. If my input sg list is a 36 byte single
sg entry then qc->cursg should be NULL by the WARN_ON() - but it isn't.
If qc->cursg is NULL when the sg_next() is run then we don't warn because
we are quite happy with the last segment being padded or underrunning.
What we actually want to explode on is a case where we transfer more
bytes than are wanted and where there are more sg entries to perform - at
that point we would corrupt.
So at least one failure case is
Core code issues an SG list for 96 bytes
Drive indicates it wishes to return 18 bytes
data_xfer transfers 18 bytes + 2 padding (correctly) -> 20 bytes
At this point __atapi_pio_bytes breaks
it updates qc->curbytes by 18
it updates the offset by 18
The last segment is not exhausted so it does not update qc->cursg
qc->cursg is not updated and the WARN erroneously uses !=
The bogus WARN_ON_ONCE() triggers.
So the bug is the WARN_ON being wrong. In fact __atapi_pio_bytes doesn't
know enough to do the WARN check correctly as it doesn't know if it is
the last request being made. It just happens it didn't break before
because all our transfers are word aligned.
We can remove the WARN for the moment, but someone should probably fix
the sanity check logic.
Alan
> > Nope.. you can't do that with ATA block transfers - it isn't the same as
> > SCSI
>
> Well, in that case you'll have to do byte PIO for all ATAPI devices,
> because this is an expected device to host transfer length.
Not possible there is no such thing as byte PIO in ATAPI.
See my other mail - it appears to be a long standing bug in
__atapi_pio_sector rather than a corrupt sg list as I first thought.
Hello.
James Bottomley wrote:
>>>not divisible by four. If you want to use word based PIO, you'll have
>>>to fall back to collecting bytes for the last two. Alternatively, you
>>Nope.. you can't do that with ATA block transfers - it isn't the same as
>>SCSI
> Well, in that case you'll have to do byte PIO for all ATAPI devices,
> because this is an expected device to host transfer length.
Byte PIO doesn't work in the ATA world unless the device supports it (I
guess only CFA devices really support it) and the driver has enabled it (which
I think isn't really worth it unless you have some h/w constaints). What you
can do is read the whole 16-bit (or 32-bit) word and ignore the bytes you
don't need.
MBR, Sergei
> The ATAPI logic is more complex since it has to take into account the
> arbitrary byte count that a device want to transfer on each INTRQ (read from
> the byte count low/high regs).
Actually our ATAPI logic plain doesn't work for arbitary byte counts but
that is another story that needs looking into now the can of worms has
been noticed and opened.
Alan Cox wrote:
>> All the S/G counts printed out were divisible by 4 (36 for INQUIRY and 96
>>for REQUSET SENSE). It's the *actual* byte count for the REQUEST SENSE that's
>>no divisible. The SCSI/ATAPI devices are free to sent less data than requested
>>on non block transfer commands.
> That is just fine - if the sg list is not corrupt or being mishandled and
> the atapi pio code is not buggy.
> RTFS a bit and it becomes obvious that the core libata code has a bug:
Oh, I have already... and saw where the issue could be. It just wasn't
obvious why 32-bit PIO triggered it.
> From libata-sff.c:
> /* consumed can be larger than count only for the last transfer */
> WARN_ON_ONCE(qc->cursg && count != consumed);
>
> The big clue turns out to be that the code doesn't match the comment.
>
> Next note the check on qc->cursg. If my input sg list is a 36 byte single
> sg entry then qc->cursg should be NULL by the WARN_ON() - but it isn't.
I think it's still not NULL because qc->cursg_ofs == sg->length check was
*not* true right above, hence sg_next() wasn't called...
> If qc->cursg is NULL when the sg_next() is run then we don't warn because
> we are quite happy with the last segment being padded or underrunning.
I don't think that sg_next() is called on an underrun segment. And here
lies the mistake.
> What we actually want to explode on is a case where we transfer more
> bytes than are wanted and where there are more sg entries to perform - at
> that point we would corrupt.
> So at least one failure case is
> Core code issues an SG list for 96 bytes
> Drive indicates it wishes to return 18 bytes
> data_xfer transfers 18 bytes + 2 padding (correctly) -> 20 bytes
> At this point __atapi_pio_bytes breaks
> it updates qc->curbytes by 18
> it updates the offset by 18
> The last segment is not exhausted so it does not update qc->cursg
> qc->cursg is not updated and the WARN erroneously uses !=
> The bogus WARN_ON_ONCE() triggers.
Yes.
> So the bug is the WARN_ON being wrong. In fact __atapi_pio_bytes doesn't
> know enough to do the WARN check correctly as it doesn't know if it is
> the last request being made. It just happens it didn't break before
> because all our transfers are word aligned.
Er... I'm not sure what's changed with 32-bit PIO patch.
> Alan
MBR, Sergei
Hello, I wrote:
>>> All the S/G counts printed out were divisible by 4 (36 for
>>> INQUIRY and 96 for REQUSET SENSE). It's the *actual* byte count for
>>> the REQUEST SENSE that's no divisible. The SCSI/ATAPI devices are
>>> free to sent less data than requested on non block transfer commands.
>
>> That is just fine - if the sg list is not corrupt or being mishandled
>> and
>> the atapi pio code is not buggy.
>
>> RTFS a bit and it becomes obvious that the core libata code has a bug:
>
> Oh, I have already... and saw where the issue could be. It just
> wasn't obvious why 32-bit PIO triggered it.
Got it now, however the issue doesn't seem as evident simple to me...
>> From libata-sff.c:
>> /* consumed can be larger than count only for the last
>> transfer */
>> WARN_ON_ONCE(qc->cursg && count != consumed);
>>
>> The big clue turns out to be that the code doesn't match the comment.
>>
>> Next note the check on qc->cursg. If my input sg list is a 36 byte
>> single
>> sg entry then qc->cursg should be NULL by the WARN_ON() - but it isn't.
>
> I think it's still not NULL because qc->cursg_ofs == sg->length
> check was *not* true right above, hence sg_next() wasn't called...
>
>> If qc->cursg is NULL when the sg_next() is run then we don't warn
>> because
>> we are quite happy with the last segment being padded or underrunning.
>
> I don't think that sg_next() is called on an underrun segment. And
> here lies the mistake.
>
>> What we actually want to explode on is a case where we transfer more
>> bytes than are wanted and where there are more sg entries to perform
>> - at
>> that point we would corrupt.
>
>> So at least one failure case is
>
>> Core code issues an SG list for 96 bytes
>> Drive indicates it wishes to return 18 bytes
>
>> data_xfer transfers 18 bytes + 2 padding (correctly) -> 20 bytes
Correctly indeed? I'm not at all sure it's correct to read an extra
16-bit word off the device when it thinks it's already done with the
data transfer. This is not the same as to read 16-bit word and ignore
its MSB as it happened. The same concern about the writes... Note that
the IDE code doesn't do this...
MBR, Sergei
Sergei Shtylyov wrote:
> Correctly indeed? I'm not at all sure it's correct to read an extra
> 16-bit word off the device when it thinks it's already done with the
> data transfer. This is not the same as to read 16-bit word and ignore
> its MSB as it happened. The same concern about the writes... Note that
> the IDE code doesn't do this...
Nod. And that gets us back to the original point...
Jeff
Hello.
Jeff Garzik wrote:
>> Correctly indeed? I'm not at all sure it's correct to read an extra
>> 16-bit word off the device when it thinks it's already done with the
>> data transfer. This is not the same as to read 16-bit word and ignore
>> its MSB as it happened. The same concern about the writes... Note
>> that the IDE code doesn't do this...
>
> Nod. And that gets us back to the original point...
Note that Alan's point is still valid: this WARN_ON_ONCE() would
incorrectly trigger on odd length ATAPI transfers.
> Jeff
MBR Sergei
On Sat, 10 Jan 2009 13:51:04 +0000
Alan Cox <[email protected]> wrote:
> > 2.6.28 is OK
> > 2.6.28 + PIO32 is broken
>
> As far as I can tell
>
> 2.6.28 is broken but it doesn't show due to other factors
> 2.6.28 using 32bit PIO shows up the fact someone seems to be passing
> broken sg lists
are you sure; I have lots of these in kerneloops.org... so it does show
somewhat in 2.6.28... (assuming it's the exact same underlying bug
obviously)
--
Arjan van de Ven Intel Open Source Technology Centre
For development, discussion and tips for power savings,
visit http://www.lesswatts.org
> >> data_xfer transfers 18 bytes + 2 padding (correctly) -> 20 bytes
>
> Correctly indeed? I'm not at all sure it's correct to read an extra
> 16-bit word off the device when it thinks it's already done with the
> data transfer.
The VLB controller docs explicitly require you do entirely 32bit. The AMD
ones seem to imply you should.
Its easy enough to not do that but for the VLB case we have to so the
WARN needs fixing which ever path we go down.
Hello.
Alan Cox wrote:
>>>> data_xfer transfers 18 bytes + 2 padding (correctly) -> 20 bytes
>>>>
>> Correctly indeed? I'm not at all sure it's correct to read an extra
>> 16-bit word off the device when it thinks it's already done with the
>> data transfer.
>>
OTOH, once can generally read the data register with no command
active and not have anything locked up, so I'm not sure of how risky
this can be... it's better to exclude such risk though.
> The VLB controller docs explicitly require you do entirely 32bit.
Didn't VLB contollers largely predate ATAPI devices?
> The AMD ones seem to imply you should.
>
Indeed, AMD-8111 datasheet requires 32-bit writes -- but only when
the write buffer is enabled.
> Its easy enough to not do that but for the VLB case we have to so the
> WARN needs fixing which ever path we go down.
>
Sure.
MBR, Sergei
> > The VLB controller docs explicitly require you do entirely 32bit.
>
> Didn't VLB contollers largely predate ATAPI devices?
Yes but they generally work with ATAPI.
Jeff, Alan,
this is still not fixed upstream. What about:
[PATCH] ata: fix wrong WARN_ON_ONCE
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.
Signed-off-by: Christian Borntraeger <[email protected]>
---
drivers/ata/libata-sff.c | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
Index: linux-2.6/drivers/ata/libata-sff.c
===================================================================
--- linux-2.6.orig/drivers/ata/libata-sff.c
+++ linux-2.6/drivers/ata/libata-sff.c
@@ -1013,9 +1013,12 @@ next_sg:
qc->cursg_ofs = 0;
}
- /* consumed can be larger than count only for the last transfer */
- WARN_ON_ONCE(qc->cursg && count != consumed);
-
+ /*
+ * There used to be a WARN_ON_ONCE(qc->cursg && count != consumed);
+ * Unfortunately __atapi_pio_bytes doesn't know enough to do the WARN
+ * check correctly as it doesn't know if it is the last request being
+ * made. Somebody should implement a proper sanity check.
+ */
if (bytes)
goto next_sg;
return 0;