Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
Link to manufacturer wiki: http://wiki.iteadstudio.com/Iteaduino_Plus_A10/A20
Signed-off-by: Josef Gajdusek <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts | 202 +++++++++++++++++++++++++
2 files changed, 203 insertions(+)
create mode 100644 arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index adb1826..6104ed1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -529,6 +529,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-hackberry.dtb \
sun4i-a10-hyundai-a7hd.dtb \
sun4i-a10-inet97fv2.dtb \
+ sun4i-a10-iteaduino-plus.dts \
sun4i-a10-jesurun-q5.dtb \
sun4i-a10-marsboard.dtb \
sun4i-a10-mini-xplus.dtb \
diff --git a/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts b/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
new file mode 100644
index 0000000..985e155
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
@@ -0,0 +1,202 @@
+/*
+ * Copyright 2015 Josef Gajdusek <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Iteaduino Plus A10";
+ compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&emac_sram {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.3.6
Hi,
Thanks for your patch.
On Sun, Jul 19, 2015 at 03:45:03PM +0200, Josef Gajdusek wrote:
> Iteaduino Plus A10 is a breakout board + Itead Core A10.
Is there multiple breakout boards available for that module?
> It features 1GB RAM, has most of the A10 pins on a .1" header, 2 USB
> ports, 1 OTG USB port, Ethernet, HDMI, SATA, Speaker/Microphone
> 3.5mm jacks and an SD card slot.
>
> Link to manufacturer wiki: http://wiki.iteadstudio.com/Iteaduino_Plus_A10/A20
Please don't put such links in the commit description. Valid URLs come
and go, the git history doesn't.
> Signed-off-by: Josef Gajdusek <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts | 202 +++++++++++++++++++++++++
> 2 files changed, 203 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index adb1826..6104ed1 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -529,6 +529,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
> sun4i-a10-hackberry.dtb \
> sun4i-a10-hyundai-a7hd.dtb \
> sun4i-a10-inet97fv2.dtb \
> + sun4i-a10-iteaduino-plus.dts \
> sun4i-a10-jesurun-q5.dtb \
> sun4i-a10-marsboard.dtb \
> sun4i-a10-mini-xplus.dtb \
> diff --git a/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts b/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
> new file mode 100644
> index 0000000..985e155
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun4i-a10-iteaduino-plus.dts
we try to have a DT name that is
<family>-<soc>-<manufacturer>-<device>.dts
Which in this case would be sun4i-a10-itead-iteaduino-plus.dts
> @@ -0,0 +1,202 @@
> +/*
> + * Copyright 2015 Josef Gajdusek <[email protected]>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun4i-a10.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> + model = "Iteaduino Plus A10";
> + compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&ahci {
> + target-supply = <®_ahci_5v>;
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdc2>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&emac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emac_pins_a>;
> + phy = <&phy1>;
> + status = "okay";
> +};
> +
> +&emac_sram {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins_a>;
> + status = "okay";
> +
> + axp209: pmic@34 {
> + reg = <0x34>;
> + interrupts = <0>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_a>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + status = "okay";
> +};
> +
> +&ir0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir0_rx_pins_a>;
> + status = "okay";
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +®_ahci_5v {
> + status = "okay";
> +};
> +
> +#include "axp209.dtsi"
> +
> +®_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +®_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +®_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +®_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +®_usb1_vbus {
> + status = "okay";
> +};
> +
> +®_usb2_vbus {
> + status = "okay";
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pins_a>,
> + <&spi0_cs0_pins_a>;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb1_vbus-supply = <®_usb1_vbus>;
> + usb2_vbus-supply = <®_usb2_vbus>;
> + status = "okay";
> +};
Looks good otherwise, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
Signed-off-by: Josef Gajdusek <[email protected]>
---
It does not look like there are any other breakout boards for Core A10/A20
modules.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun4i-a10-itead-iteaduino-plus.dts | 202 +++++++++++++++++++++
2 files changed, 203 insertions(+)
create mode 100644 arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index adb1826..564d5a8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -529,6 +529,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-hackberry.dtb \
sun4i-a10-hyundai-a7hd.dtb \
sun4i-a10-inet97fv2.dtb \
+ sun4i-a10-itead-iteaduino-plus.dts \
sun4i-a10-jesurun-q5.dtb \
sun4i-a10-marsboard.dtb \
sun4i-a10-mini-xplus.dtb \
diff --git a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
new file mode 100644
index 0000000..985e155
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
@@ -0,0 +1,202 @@
+/*
+ * Copyright 2015 Josef Gajdusek <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Iteaduino Plus A10";
+ compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&emac_sram {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.3.6
On Mon, Jul 20, 2015 at 10:53:18PM +0200, Josef Gajdusek wrote:
> Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
> has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
> Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
>
> Signed-off-by: Josef Gajdusek <[email protected]>
Applied, thanks.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com