Add a driver which supports :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.
Signed-off-by: Mathieu OTHACEHE <[email protected]>
---
Hi Johan,
Thanks for your patience, here is v5,
Mathieu
Changes in v2:
* Use generic implementation for read/write code
* Use TIOCSRS485/TIOCGRS485 instead of moxa specific ioctl
* Other problems pointed out by Johan review
Changes in v3:
* Drop unused defines
* Fix style problems
* Remove port identification code since this driver is for one-port devices only
* Fix debug messages
* Use a mutex to protect shadow_mc
* Use usb_serial_generic_open and close
* Other problems pointed out by Johan review
Changes in v4:
* mxu1_startup return -ENODEV on purpose if the firmware was downloaded.
It avoids port_probe to fail since the device is reset.
Changes in v5:
* Drop debug messages
* Drop useless fields from mxu1_port and mxu1_device structures
* Return supported bits to userspace in function mxu1_ioctl_set_rs485
* Other problems pointed out by Johan review
drivers/usb/serial/Kconfig | 16 +
drivers/usb/serial/Makefile | 1 +
drivers/usb/serial/mxu11x0.c | 1069 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1086 insertions(+)
create mode 100644 drivers/usb/serial/mxu11x0.c
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 56ecb8b..f612dda 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -475,6 +475,22 @@ config USB_SERIAL_MOS7840
To compile this driver as a module, choose M here: the
module will be called mos7840. If unsure, choose N.
+config USB_SERIAL_MXUPORT11
+ tristate "USB Moxa UPORT 11x0 Serial Driver"
+ ---help---
+ Say Y here if you want to use a MOXA UPort 11x0 Serial hub.
+
+ This driver supports:
+
+ - UPort 1110 : 1 port RS-232 USB to Serial Hub.
+ - UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
+ - UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
+ - UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
+ - UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mxu11x0.
+
config USB_SERIAL_MXUPORT
tristate "USB Moxa UPORT Serial Driver"
---help---
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index 349d9df..f3fa5e5 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_USB_SERIAL_METRO) += metro-usb.o
obj-$(CONFIG_USB_SERIAL_MOS7720) += mos7720.o
obj-$(CONFIG_USB_SERIAL_MOS7840) += mos7840.o
obj-$(CONFIG_USB_SERIAL_MXUPORT) += mxuport.o
+obj-$(CONFIG_USB_SERIAL_MXUPORT11) += mxu11x0.o
obj-$(CONFIG_USB_SERIAL_NAVMAN) += navman.o
obj-$(CONFIG_USB_SERIAL_OMNINET) += omninet.o
obj-$(CONFIG_USB_SERIAL_OPTICON) += opticon.o
diff --git a/drivers/usb/serial/mxu11x0.c b/drivers/usb/serial/mxu11x0.c
new file mode 100644
index 0000000..db7ed1f
--- /dev/null
+++ b/drivers/usb/serial/mxu11x0.c
@@ -0,0 +1,1069 @@
+/*
+ *
+ * USB Moxa UPORT 11x0 Serial Driver
+ *
+ * Copyright (C) 2007 MOXA Technologies Co., Ltd.
+ * Copyright (C) 2015 Mathieu Othacehe <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ *
+ * Supports the following Moxa USB to serial converters:
+ * UPort 1110, 1 port RS-232 USB to Serial Hub.
+ * UPort 1130, 1 port RS-422/485 USB to Serial Hub.
+ * UPort 1130I, 1 port RS-422/485 USB to Serial Hub with isolation
+ * protection.
+ * UPort 1150, 1 port RS-232/422/485 USB to Serial Hub.
+ * UPort 1150I, 1 port RS-232/422/485 USB to Serial Hub with isolation
+ * protection.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/firmware.h>
+#include <linux/jiffies.h>
+#include <linux/serial.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/mutex.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <linux/uaccess.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+
+/* Vendor and product ids */
+#define MXU1_VENDOR_ID 0x110a
+#define MXU1_1110_PRODUCT_ID 0x1110
+#define MXU1_1130_PRODUCT_ID 0x1130
+#define MXU1_1150_PRODUCT_ID 0x1150
+#define MXU1_1151_PRODUCT_ID 0x1151
+#define MXU1_1131_PRODUCT_ID 0x1131
+
+/* Commands */
+#define MXU1_GET_VERSION 0x01
+#define MXU1_GET_PORT_STATUS 0x02
+#define MXU1_GET_PORT_DEV_INFO 0x03
+#define MXU1_GET_CONFIG 0x04
+#define MXU1_SET_CONFIG 0x05
+#define MXU1_OPEN_PORT 0x06
+#define MXU1_CLOSE_PORT 0x07
+#define MXU1_START_PORT 0x08
+#define MXU1_STOP_PORT 0x09
+#define MXU1_TEST_PORT 0x0A
+#define MXU1_PURGE_PORT 0x0B
+#define MXU1_RESET_EXT_DEVICE 0x0C
+#define MXU1_GET_OUTQUEUE 0x0D
+#define MXU1_WRITE_DATA 0x80
+#define MXU1_READ_DATA 0x81
+#define MXU1_REQ_TYPE_CLASS 0x82
+
+/* Module identifiers */
+#define MXU1_I2C_PORT 0x01
+#define MXU1_IEEE1284_PORT 0x02
+#define MXU1_UART1_PORT 0x03
+#define MXU1_UART2_PORT 0x04
+#define MXU1_RAM_PORT 0x05
+
+/* Modem status */
+#define MXU1_MSR_DELTA_CTS 0x01
+#define MXU1_MSR_DELTA_DSR 0x02
+#define MXU1_MSR_DELTA_RI 0x04
+#define MXU1_MSR_DELTA_CD 0x08
+#define MXU1_MSR_CTS 0x10
+#define MXU1_MSR_DSR 0x20
+#define MXU1_MSR_RI 0x40
+#define MXU1_MSR_CD 0x80
+#define MXU1_MSR_DELTA_MASK 0x0F
+#define MXU1_MSR_MASK 0xF0
+
+/* Line status */
+#define MXU1_LSR_OVERRUN_ERROR 0x01
+#define MXU1_LSR_PARITY_ERROR 0x02
+#define MXU1_LSR_FRAMING_ERROR 0x04
+#define MXU1_LSR_BREAK 0x08
+#define MXU1_LSR_ERROR 0x0F
+#define MXU1_LSR_RX_FULL 0x10
+#define MXU1_LSR_TX_EMPTY 0x20
+
+/* Modem control */
+#define MXU1_MCR_LOOP 0x04
+#define MXU1_MCR_DTR 0x10
+#define MXU1_MCR_RTS 0x20
+
+/* Mask settings */
+#define MXU1_UART_ENABLE_RTS_IN 0x0001
+#define MXU1_UART_DISABLE_RTS 0x0002
+#define MXU1_UART_ENABLE_PARITY_CHECKING 0x0008
+#define MXU1_UART_ENABLE_DSR_OUT 0x0010
+#define MXU1_UART_ENABLE_CTS_OUT 0x0020
+#define MXU1_UART_ENABLE_X_OUT 0x0040
+#define MXU1_UART_ENABLE_XA_OUT 0x0080
+#define MXU1_UART_ENABLE_X_IN 0x0100
+#define MXU1_UART_ENABLE_DTR_IN 0x0800
+#define MXU1_UART_DISABLE_DTR 0x1000
+#define MXU1_UART_ENABLE_MS_INTS 0x2000
+#define MXU1_UART_ENABLE_AUTO_START_DMA 0x4000
+#define MXU1_UART_SEND_BREAK_SIGNAL 0x8000
+
+/* Parity */
+#define MXU1_UART_NO_PARITY 0x00
+#define MXU1_UART_ODD_PARITY 0x01
+#define MXU1_UART_EVEN_PARITY 0x02
+#define MXU1_UART_MARK_PARITY 0x03
+#define MXU1_UART_SPACE_PARITY 0x04
+
+/* Stop bits */
+#define MXU1_UART_1_STOP_BITS 0x00
+#define MXU1_UART_1_5_STOP_BITS 0x01
+#define MXU1_UART_2_STOP_BITS 0x02
+
+/* Bits per character */
+#define MXU1_UART_5_DATA_BITS 0x00
+#define MXU1_UART_6_DATA_BITS 0x01
+#define MXU1_UART_7_DATA_BITS 0x02
+#define MXU1_UART_8_DATA_BITS 0x03
+
+/* Operation modes */
+#define MXU1_UART_232 0x00
+#define MXU1_UART_485_RECEIVER_DISABLED 0x01
+#define MXU1_UART_485_RECEIVER_ENABLED 0x02
+
+/* Supported operation types */
+#define MXU1_TYPE_RS232 BIT(0)
+#define MXU1_TYPE_RS422 BIT(1)
+#define MXU1_TYPE_RS485 BIT(2)
+
+/* Pipe transfer mode and timeout */
+#define MXU1_PIPE_MODE_CONTINUOUS 0x01
+#define MXU1_PIPE_MODE_MASK 0x03
+#define MXU1_PIPE_TIMEOUT_MASK 0x7C
+#define MXU1_PIPE_TIMEOUT_ENABLE 0x80
+
+/* Config struct */
+struct mxu1_uart_config {
+ __be16 wBaudRate;
+ __be16 wFlags;
+ u8 bDataBits;
+ u8 bParity;
+ u8 bStopBits;
+ char cXon;
+ char cXoff;
+ u8 bUartMode;
+} __packed;
+
+/* Purge modes */
+#define MXU1_PURGE_OUTPUT 0x00
+#define MXU1_PURGE_INPUT 0x80
+
+/* Read/Write data */
+#define MXU1_RW_DATA_ADDR_SFR 0x10
+#define MXU1_RW_DATA_ADDR_IDATA 0x20
+#define MXU1_RW_DATA_ADDR_XDATA 0x30
+#define MXU1_RW_DATA_ADDR_CODE 0x40
+#define MXU1_RW_DATA_ADDR_GPIO 0x50
+#define MXU1_RW_DATA_ADDR_I2C 0x60
+#define MXU1_RW_DATA_ADDR_FLASH 0x70
+#define MXU1_RW_DATA_ADDR_DSP 0x80
+
+#define MXU1_RW_DATA_UNSPECIFIED 0x00
+#define MXU1_RW_DATA_BYTE 0x01
+#define MXU1_RW_DATA_WORD 0x02
+#define MXU1_RW_DATA_DOUBLE_WORD 0x04
+
+struct mxu1_write_data_bytes {
+ u8 bAddrType;
+ u8 bDataType;
+ u8 bDataCounter;
+ __be16 wBaseAddrHi;
+ __be16 wBaseAddrLo;
+ u8 bData[0];
+} __packed;
+
+/* Interrupt codes */
+#define MXU1_CODE_HARDWARE_ERROR 0xFF
+#define MXU1_CODE_DATA_ERROR 0x03
+#define MXU1_CODE_MODEM_STATUS 0x04
+
+static inline int mxu1_get_func_from_code(unsigned char code)
+{
+ return code & 0x0f;
+}
+
+/* Download firmware max packet size */
+#define MXU1_DOWNLOAD_MAX_PACKET_SIZE 64
+
+/* Firmware image header */
+struct mxu1_firmware_header {
+ __le16 wLength;
+ u8 bCheckSum;
+} __packed;
+
+#define MXU1_UART_BASE_ADDR 0xFFA0
+#define MXU1_UART_OFFSET_MCR 0x0004
+
+#define MXU1_BAUD_BASE 923077
+
+#define MXU1_TRANSFER_TIMEOUT 2
+#define MXU1_DOWNLOAD_TIMEOUT 1000
+#define MXU1_DEFAULT_CLOSING_WAIT 4000 /* in .01 secs */
+
+struct mxu1_port {
+ u8 msr;
+ u8 mcr;
+ u8 uart_types;
+ u8 uart_mode;
+ spinlock_t spinlock; /* Protects msr */
+ struct mutex mutex; /* Protects mcr */
+ bool send_break;
+};
+
+struct mxu1_device {
+ u16 mxd_model;
+};
+
+static const struct usb_device_id mxu1_idtable[] = {
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1110_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1130_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1150_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1151_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1131_PRODUCT_ID) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, mxu1_idtable);
+
+/* Write the given buffer out to the control pipe. */
+static int mxu1_send_ctrl_data_urb(struct usb_serial *serial,
+ u8 request,
+ u16 value, u16 index,
+ void *data, size_t size)
+{
+ int status;
+
+ status = usb_control_msg(serial->dev,
+ usb_sndctrlpipe(serial->dev, 0),
+ request,
+ (USB_DIR_OUT | USB_TYPE_VENDOR |
+ USB_RECIP_DEVICE), value, index,
+ data, size,
+ USB_CTRL_SET_TIMEOUT);
+ if (status < 0) {
+ dev_err(&serial->interface->dev,
+ "%s - usb_control_msg failed: %d\n",
+ __func__, status);
+ return status;
+ }
+
+ if (status != size) {
+ dev_err(&serial->interface->dev,
+ "%s - short write (%d / %zd)\n",
+ __func__, status, size);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/* Send a vendor request without any data */
+static int mxu1_send_ctrl_urb(struct usb_serial *serial,
+ u8 request, u16 value, u16 index)
+{
+ return mxu1_send_ctrl_data_urb(serial, request, value, index,
+ NULL, 0);
+}
+
+static int mxu1_download_firmware(struct usb_serial *serial,
+ const struct firmware *fw_p)
+{
+ int status = 0;
+ int buffer_size;
+ int pos;
+ int len;
+ int done;
+ u8 cs = 0;
+ u8 *buffer;
+ struct usb_device *dev = serial->dev;
+ struct mxu1_firmware_header *header;
+ unsigned int pipe;
+
+ pipe = usb_sndbulkpipe(dev, serial->port[0]->bulk_out_endpointAddress);
+
+ buffer_size = fw_p->size + sizeof(*header);
+ buffer = kmalloc(buffer_size, GFP_KERNEL);
+ if (!buffer)
+ return -ENOMEM;
+
+ memcpy(buffer, fw_p->data, fw_p->size);
+ memset(buffer + fw_p->size, 0xff, buffer_size - fw_p->size);
+
+ for (pos = sizeof(*header); pos < buffer_size; pos++)
+ cs = (u8)(cs + buffer[pos]);
+
+ header = (struct mxu1_firmware_header *)buffer;
+ header->wLength = cpu_to_le16(buffer_size - sizeof(*header));
+ header->bCheckSum = cs;
+
+ dev_dbg(&dev->dev, "%s - downloading firmware\n", __func__);
+
+ for (pos = 0; pos < buffer_size; pos += done) {
+ len = min(buffer_size - pos, MXU1_DOWNLOAD_MAX_PACKET_SIZE);
+
+ status = usb_bulk_msg(dev, pipe, buffer + pos, len, &done,
+ MXU1_DOWNLOAD_TIMEOUT);
+ if (status)
+ break;
+ }
+
+ kfree(buffer);
+
+ if (status) {
+ dev_err(&dev->dev, "failed to download firmware: %d\n", status);
+ return status;
+ }
+
+ msleep_interruptible(100);
+ usb_reset_device(dev);
+
+ dev_dbg(&dev->dev, "%s - download successful\n", __func__);
+
+ return 0;
+}
+
+static int mxu1_port_probe(struct usb_serial_port *port)
+{
+ struct mxu1_port *mxport;
+ struct mxu1_device *mxdev;
+ struct urb *urb;
+
+ mxport = kzalloc(sizeof(struct mxu1_port), GFP_KERNEL);
+ if (!mxport)
+ return -ENOMEM;
+
+ spin_lock_init(&mxport->spinlock);
+ mutex_init(&mxport->mutex);
+
+ mxdev = usb_get_serial_data(port->serial);
+
+ urb = port->interrupt_in_urb;
+ if (!urb) {
+ dev_err(&port->dev, "%s - no interrupt urb\n", __func__);
+ return -EINVAL;
+ }
+
+ switch (mxdev->mxd_model) {
+ case MXU1_1110_PRODUCT_ID:
+ mxport->uart_types = MXU1_TYPE_RS232;
+ mxport->uart_mode = MXU1_UART_232;
+ break;
+ case MXU1_1130_PRODUCT_ID:
+ case MXU1_1131_PRODUCT_ID:
+ mxport->uart_types = MXU1_TYPE_RS422 | MXU1_TYPE_RS485;
+ mxport->uart_mode = MXU1_UART_485_RECEIVER_DISABLED;
+ break;
+ case MXU1_1150_PRODUCT_ID:
+ case MXU1_1151_PRODUCT_ID:
+ mxport->uart_types =
+ MXU1_TYPE_RS232 | MXU1_TYPE_RS422 | MXU1_TYPE_RS485;
+ mxport->uart_mode = MXU1_UART_232;
+ break;
+ }
+
+ usb_set_serial_port_data(port, mxport);
+
+ port->port.closing_wait =
+ msecs_to_jiffies(MXU1_DEFAULT_CLOSING_WAIT * 10);
+ port->port.drain_delay = 1;
+
+ return 0;
+}
+
+static int mxu1_startup(struct usb_serial *serial)
+{
+ struct mxu1_device *mxdev;
+ struct usb_device *dev = serial->dev;
+ struct usb_host_interface *cur_altsetting;
+ char fw_name[32];
+ const struct firmware *fw_p = NULL;
+ int err;
+ int status = 0;
+
+ dev_dbg(&serial->interface->dev, "%s - product 0x%04X, num configurations %d, configuration value %d\n",
+ __func__, le16_to_cpu(dev->descriptor.idProduct),
+ dev->descriptor.bNumConfigurations,
+ dev->actconfig->desc.bConfigurationValue);
+
+ /* create device structure */
+ mxdev = kzalloc(sizeof(struct mxu1_device), GFP_KERNEL);
+ if (!mxdev)
+ return -ENOMEM;
+
+ usb_set_serial_data(serial, mxdev);
+
+ mxdev->mxd_model = le16_to_cpu(dev->descriptor.idProduct);
+
+ cur_altsetting = serial->interface->cur_altsetting;
+
+ /* if we have only 1 configuration, download firmware */
+ if (cur_altsetting->desc.bNumEndpoints == 1) {
+
+ snprintf(fw_name,
+ sizeof(fw_name),
+ "moxa/moxa-%04x.fw",
+ mxdev->mxd_model);
+
+ err = request_firmware(&fw_p, fw_name, &serial->interface->dev);
+ if (err) {
+ dev_err(&serial->interface->dev, "failed to request firmware: %d\n",
+ err);
+ kfree(mxdev);
+ return err;
+ }
+
+ err = mxu1_download_firmware(serial, fw_p);
+ if (err) {
+ kfree(mxdev);
+ release_firmware(fw_p);
+ return err;
+ }
+
+ status = -ENODEV;
+ release_firmware(fw_p);
+ }
+
+ return status;
+}
+
+static int mxu1_write_byte(struct usb_serial_port *port, u32 addr,
+ u8 mask, u8 byte)
+{
+ int status;
+ size_t size;
+ struct mxu1_write_data_bytes *data;
+
+ dev_dbg(&port->dev, "%s - addr 0x%08X, mask 0x%02X, byte 0x%02X\n",
+ __func__, addr, mask, byte);
+
+ size = sizeof(struct mxu1_write_data_bytes) + 2;
+ data = kzalloc(size, GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->bAddrType = MXU1_RW_DATA_ADDR_XDATA;
+ data->bDataType = MXU1_RW_DATA_BYTE;
+ data->bDataCounter = 1;
+ data->wBaseAddrHi = cpu_to_be16(addr >> 16);
+ data->wBaseAddrLo = cpu_to_be16(addr);
+ data->bData[0] = mask;
+ data->bData[1] = byte;
+
+ status = mxu1_send_ctrl_data_urb(port->serial, MXU1_WRITE_DATA, 0,
+ MXU1_RAM_PORT, data, size);
+ if (status < 0)
+ dev_err(&port->dev, "%s - failed: %d\n", __func__, status);
+
+ kfree(data);
+
+ return status;
+}
+
+static int mxu1_set_mcr(struct usb_serial_port *port, unsigned int mcr)
+{
+ int status;
+
+ status = mxu1_write_byte(port,
+ MXU1_UART_BASE_ADDR + MXU1_UART_OFFSET_MCR,
+ MXU1_MCR_RTS | MXU1_MCR_DTR | MXU1_MCR_LOOP,
+ mcr);
+ return status;
+}
+
+static void mxu1_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port,
+ struct ktermios *old_termios)
+{
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ struct mxu1_uart_config *config;
+ tcflag_t cflag, iflag;
+ speed_t baud;
+ int status;
+ unsigned int mcr;
+
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
+
+ if (old_termios &&
+ !tty_termios_hw_change(&tty->termios, old_termios) &&
+ tty->termios.c_iflag == old_termios->c_iflag) {
+ dev_dbg(&port->dev, "%s - nothing to change\n", __func__);
+ return;
+ }
+
+ dev_dbg(&port->dev,
+ "%s - clfag %08x, iflag %08x\n", __func__, cflag, iflag);
+
+ if (old_termios) {
+ dev_dbg(&port->dev, "%s - old clfag %08x, old iflag %08x\n",
+ __func__,
+ old_termios->c_cflag,
+ old_termios->c_iflag);
+ }
+
+ config = kzalloc(sizeof(*config), GFP_KERNEL);
+ if (!config)
+ return;
+
+ /* these flags must be set */
+ config->wFlags |= MXU1_UART_ENABLE_MS_INTS;
+ config->wFlags |= MXU1_UART_ENABLE_AUTO_START_DMA;
+ if (mxport->send_break)
+ config->wFlags |= MXU1_UART_SEND_BREAK_SIGNAL;
+ config->bUartMode = mxport->uart_mode;
+
+ switch (C_CSIZE(tty)) {
+ case CS5:
+ config->bDataBits = MXU1_UART_5_DATA_BITS;
+ break;
+ case CS6:
+ config->bDataBits = MXU1_UART_6_DATA_BITS;
+ break;
+ case CS7:
+ config->bDataBits = MXU1_UART_7_DATA_BITS;
+ break;
+ default:
+ case CS8:
+ config->bDataBits = MXU1_UART_8_DATA_BITS;
+ break;
+ }
+
+ if (C_PARENB(tty)) {
+ config->wFlags |= MXU1_UART_ENABLE_PARITY_CHECKING;
+ if (C_CMSPAR(tty)) {
+ if (C_PARODD(tty))
+ config->bParity = MXU1_UART_MARK_PARITY;
+ else
+ config->bParity = MXU1_UART_SPACE_PARITY;
+ } else {
+ if (C_PARODD(tty))
+ config->bParity = MXU1_UART_ODD_PARITY;
+ else
+ config->bParity = MXU1_UART_EVEN_PARITY;
+ }
+ } else {
+ config->bParity = MXU1_UART_NO_PARITY;
+ }
+
+ if (C_CSTOPB(tty))
+ config->bStopBits = MXU1_UART_2_STOP_BITS;
+ else
+ config->bStopBits = MXU1_UART_1_STOP_BITS;
+
+ if (C_CRTSCTS(tty)) {
+ /* RTS flow control must be off to drop RTS for baud rate B0 */
+ if (C_BAUD(tty) != B0)
+ config->wFlags |= MXU1_UART_ENABLE_RTS_IN;
+ config->wFlags |= MXU1_UART_ENABLE_CTS_OUT;
+ }
+
+ if (I_IXOFF(tty) || I_IXON(tty)) {
+ config->cXon = START_CHAR(tty);
+ config->cXoff = STOP_CHAR(tty);
+
+ if (I_IXOFF(tty))
+ config->wFlags |= MXU1_UART_ENABLE_X_IN;
+
+ if (I_IXON(tty))
+ config->wFlags |= MXU1_UART_ENABLE_X_OUT;
+ }
+
+ baud = tty_get_baud_rate(tty);
+ if (!baud)
+ baud = 9600;
+ config->wBaudRate = MXU1_BAUD_BASE / baud;
+
+ dev_dbg(&port->dev, "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n",
+ __func__, baud, config->wBaudRate, config->wFlags,
+ config->bDataBits, config->bParity, config->bStopBits,
+ config->cXon, config->cXoff, config->bUartMode);
+
+ cpu_to_be16s(&config->wBaudRate);
+ cpu_to_be16s(&config->wFlags);
+
+ status = mxu1_send_ctrl_data_urb(port->serial, MXU1_SET_CONFIG, 0,
+ MXU1_UART1_PORT, config,
+ sizeof(*config));
+ if (status)
+ dev_err(&port->dev, "cannot set config: %d\n", status);
+
+ mutex_lock(&mxport->mutex);
+ mcr = mxport->mcr;
+
+ if (C_BAUD(tty) == B0)
+ mcr &= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
+ else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+ mcr |= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
+
+ status = mxu1_set_mcr(port, mcr);
+ if (status)
+ dev_err(&port->dev, "cannot set modem control: %d\n", status);
+ else
+ mxport->mcr = mcr;
+
+ mutex_unlock(&mxport->mutex);
+
+ kfree(config);
+}
+
+static int mxu1_ioctl_get_rs485(struct mxu1_port *mxport,
+ struct serial_rs485 __user *rs485)
+{
+ struct serial_rs485 aux;
+
+ memset(&aux, 0, sizeof(aux));
+
+ if (mxport->uart_mode == MXU1_UART_485_RECEIVER_ENABLED)
+ aux.flags = SER_RS485_ENABLED;
+
+ if (copy_to_user(rs485, &aux, sizeof(aux)))
+ return -EFAULT;
+
+ return 0;
+}
+
+static int mxu1_ioctl_set_rs485(struct usb_serial_port *port,
+ struct mxu1_port *mxport,
+ struct serial_rs485 __user *rs485_user)
+{
+ struct serial_rs485 rs485;
+ int status = 0;
+
+ if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user)))
+ return -EFAULT;
+
+ if (mxport->uart_types & (MXU1_TYPE_RS422 | MXU1_TYPE_RS485)) {
+
+ if (rs485.flags & SER_RS485_ENABLED) {
+ mxport->uart_mode = MXU1_UART_485_RECEIVER_ENABLED;
+ } else {
+ if (mxport->uart_types & MXU1_TYPE_RS232)
+ mxport->uart_mode = MXU1_UART_232;
+ else
+ mxport->uart_mode =
+ MXU1_UART_485_RECEIVER_DISABLED;
+ }
+ } else {
+ dev_err(&port->dev, "RS485 not supported by this device\n");
+ status = -EINVAL;
+ }
+
+ memset(&rs485, 0, sizeof(rs485));
+ if (mxport->uart_mode & MXU1_UART_485_RECEIVER_ENABLED)
+ rs485.flags = SER_RS485_ENABLED;
+
+ if (copy_to_user(rs485_user, &rs485, sizeof(rs485)))
+ return -EFAULT;
+
+ return status;
+}
+
+static int mxu1_get_serial_info(struct usb_serial_port *port,
+ struct serial_struct __user *ret_arg)
+{
+ struct serial_struct ret_serial;
+ unsigned cwait;
+
+ if (!ret_arg)
+ return -EFAULT;
+
+ cwait = port->port.closing_wait;
+ if (cwait != ASYNC_CLOSING_WAIT_NONE)
+ cwait = jiffies_to_msecs(cwait) / 10;
+
+ memset(&ret_serial, 0, sizeof(ret_serial));
+
+ ret_serial.type = PORT_16550A;
+ ret_serial.line = port->minor;
+ ret_serial.port = 0;
+ ret_serial.xmit_fifo_size = port->bulk_out_size;
+ ret_serial.baud_base = MXU1_BAUD_BASE;
+ ret_serial.close_delay = 5*HZ;
+ ret_serial.closing_wait = cwait;
+
+ if (copy_to_user(ret_arg, &ret_serial, sizeof(*ret_arg)))
+ return -EFAULT;
+
+ return 0;
+}
+
+
+static int mxu1_set_serial_info(struct usb_serial_port *port,
+ struct serial_struct __user *new_arg)
+{
+ struct serial_struct new_serial;
+ unsigned cwait;
+
+ if (copy_from_user(&new_serial, new_arg, sizeof(new_serial)))
+ return -EFAULT;
+
+ cwait = new_serial.closing_wait;
+ if (cwait != ASYNC_CLOSING_WAIT_NONE)
+ cwait = msecs_to_jiffies(10 * new_serial.closing_wait);
+
+ port->port.closing_wait = cwait;
+
+ return 0;
+}
+
+static int mxu1_ioctl(struct tty_struct *tty,
+ unsigned int cmd, unsigned long arg)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+
+ switch (cmd) {
+ case TIOCGSERIAL:
+ return mxu1_get_serial_info(port,
+ (struct serial_struct __user *)arg);
+ case TIOCSSERIAL:
+ return mxu1_set_serial_info(port,
+ (struct serial_struct __user *)arg);
+ case TIOCGRS485:
+ return mxu1_ioctl_get_rs485(mxport,
+ (struct serial_rs485 __user *)arg);
+ case TIOCSRS485:
+ return mxu1_ioctl_set_rs485(port, mxport,
+ (struct serial_rs485 __user *)arg);
+ }
+
+ return -ENOIOCTLCMD;
+}
+
+static int mxu1_tiocmget(struct tty_struct *tty)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ unsigned int result;
+ unsigned int msr;
+ unsigned int mcr;
+ unsigned long flags;
+
+ mutex_lock(&mxport->mutex);
+ spin_lock_irqsave(&mxport->spinlock, flags);
+
+ msr = mxport->msr;
+ mcr = mxport->mcr;
+
+ spin_unlock_irqrestore(&mxport->spinlock, flags);
+ mutex_unlock(&mxport->mutex);
+
+ result = ((mcr & MXU1_MCR_DTR) ? TIOCM_DTR : 0) |
+ ((mcr & MXU1_MCR_RTS) ? TIOCM_RTS : 0) |
+ ((mcr & MXU1_MCR_LOOP) ? TIOCM_LOOP : 0) |
+ ((msr & MXU1_MSR_CTS) ? TIOCM_CTS : 0) |
+ ((msr & MXU1_MSR_CD) ? TIOCM_CAR : 0) |
+ ((msr & MXU1_MSR_RI) ? TIOCM_RI : 0) |
+ ((msr & MXU1_MSR_DSR) ? TIOCM_DSR : 0);
+
+ dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
+
+ return result;
+}
+
+static int mxu1_tiocmset(struct tty_struct *tty,
+ unsigned int set, unsigned int clear)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ int err;
+ unsigned int mcr;
+
+ mutex_lock(&mxport->mutex);
+ mcr = mxport->mcr;
+
+ if (set & TIOCM_RTS)
+ mcr |= MXU1_MCR_RTS;
+ if (set & TIOCM_DTR)
+ mcr |= MXU1_MCR_DTR;
+ if (set & TIOCM_LOOP)
+ mcr |= MXU1_MCR_LOOP;
+
+ if (clear & TIOCM_RTS)
+ mcr &= ~MXU1_MCR_RTS;
+ if (clear & TIOCM_DTR)
+ mcr &= ~MXU1_MCR_DTR;
+ if (clear & TIOCM_LOOP)
+ mcr &= ~MXU1_MCR_LOOP;
+
+ err = mxu1_set_mcr(port, mcr);
+ if (!err)
+ mxport->mcr = mcr;
+
+ mutex_unlock(&mxport->mutex);
+
+ return err;
+}
+
+static void mxu1_break(struct tty_struct *tty, int break_state)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+
+ if (break_state == -1)
+ mxport->send_break = true;
+ else
+ mxport->send_break = false;
+
+ mxu1_set_termios(tty, port, NULL);
+}
+
+static int mxu1_open(struct tty_struct *tty, struct usb_serial_port *port)
+{
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ struct usb_serial *serial = port->serial;
+ struct urb *urb;
+ int status;
+ u16 open_settings;
+
+ open_settings = (MXU1_PIPE_MODE_CONTINUOUS |
+ MXU1_PIPE_TIMEOUT_ENABLE |
+ (MXU1_TRANSFER_TIMEOUT << 2));
+
+ mxport->msr = 0;
+
+ dev_dbg(&port->dev, "%s - start interrupt in urb\n", __func__);
+ urb = port->interrupt_in_urb;
+ status = usb_submit_urb(urb, GFP_KERNEL);
+ if (status) {
+ dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
+ status);
+ return status;
+ }
+
+ if (tty)
+ mxu1_set_termios(tty, port, NULL);
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
+ open_settings, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send open command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send start command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
+ MXU1_PURGE_INPUT, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot clear input buffers: %d\n",
+ __func__, status);
+
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
+ MXU1_PURGE_OUTPUT, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot clear output buffers: %d\n",
+ __func__, status);
+
+ goto unlink_int_urb;
+ }
+
+ /*
+ * reset the data toggle on the bulk endpoints to work around bug in
+ * host controllers where things get out of sync some times
+ */
+ usb_clear_halt(serial->dev, port->write_urb->pipe);
+ usb_clear_halt(serial->dev, port->read_urb->pipe);
+
+ if (tty)
+ mxu1_set_termios(tty, port, NULL);
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
+ open_settings, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send open command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send start command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = usb_serial_generic_open(tty, port);
+ if (status) {
+ dev_err(&port->dev, "%s - submit read urb failed: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ return status;
+
+unlink_int_urb:
+ usb_kill_urb(port->interrupt_in_urb);
+
+ return status;
+}
+
+static void mxu1_close(struct usb_serial_port *port)
+{
+ int status;
+
+ usb_serial_generic_close(port);
+ usb_kill_urb(port->interrupt_in_urb);
+
+ status = mxu1_send_ctrl_urb(port->serial, MXU1_CLOSE_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status)
+ dev_err(&port->dev, "failed to send close port command: %d\n",
+ status);
+}
+
+static void mxu1_handle_new_msr(struct usb_serial_port *port,
+ struct mxu1_port *mxport, u8 msr)
+{
+ struct async_icount *icount;
+ unsigned long flags;
+
+ dev_dbg(&port->dev, "%s - msr 0x%02X\n", __func__, msr);
+
+ spin_lock_irqsave(&mxport->spinlock, flags);
+ mxport->msr = msr & MXU1_MSR_MASK;
+ spin_unlock_irqrestore(&mxport->spinlock, flags);
+
+ if (msr & MXU1_MSR_DELTA_MASK) {
+ icount = &port->icount;
+ if (msr & MXU1_MSR_DELTA_CTS)
+ icount->cts++;
+ if (msr & MXU1_MSR_DELTA_DSR)
+ icount->dsr++;
+ if (msr & MXU1_MSR_DELTA_CD)
+ icount->dcd++;
+ if (msr & MXU1_MSR_DELTA_RI)
+ icount->rng++;
+
+ wake_up_interruptible(&port->port.delta_msr_wait);
+ }
+}
+
+static void mxu1_interrupt_callback(struct urb *urb)
+{
+ struct usb_serial_port *port = urb->context;
+ struct mxu1_port *mxport;
+ unsigned char *data = urb->transfer_buffer;
+ int length = urb->actual_length;
+ int function;
+ int status;
+ u8 msr;
+
+ mxport = usb_get_serial_port_data(port);
+
+ switch (urb->status) {
+ case 0:
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ dev_dbg(&port->dev, "%s - urb shutting down: %d\n",
+ __func__, urb->status);
+ return;
+ default:
+ dev_dbg(&port->dev, "%s - nonzero urb status: %d\n",
+ __func__, urb->status);
+ goto exit;
+ }
+
+ if (length != 2) {
+ dev_dbg(&port->dev, "%s - bad packet size: %d\n",
+ __func__, length);
+ goto exit;
+ }
+
+ if (data[0] == MXU1_CODE_HARDWARE_ERROR) {
+ dev_err(&port->dev, "%s - hardware error: %d\n",
+ __func__, data[1]);
+ goto exit;
+ }
+
+ function = mxu1_get_func_from_code(data[0]);
+
+ dev_dbg(&port->dev, "%s - function %d, data 0x%02X\n",
+ __func__, function, data[1]);
+
+ switch (function) {
+ case MXU1_CODE_DATA_ERROR:
+ dev_dbg(&port->dev, "%s - DATA ERROR, data 0x%02X\n",
+ __func__, data[1]);
+ break;
+
+ case MXU1_CODE_MODEM_STATUS:
+ msr = data[1];
+ mxu1_handle_new_msr(port, mxport, msr);
+ break;
+
+ default:
+ dev_err(&port->dev, "%s - unknown interrupt code: 0x%02X\n",
+ __func__, data[1]);
+ break;
+ }
+
+exit:
+ status = usb_submit_urb(urb, GFP_ATOMIC);
+ if (status)
+ dev_err(&port->dev, "resubmit interrupt urb failed: %d\n",
+ status);
+}
+
+static struct usb_serial_driver mxuport11_device = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "mxuport11",
+ },
+ .description = "MOXA UPort 11x0",
+ .id_table = mxu1_idtable,
+ .num_ports = 1,
+ .port_probe = mxu1_port_probe,
+ .attach = mxu1_startup,
+ .open = mxu1_open,
+ .close = mxu1_close,
+ .ioctl = mxu1_ioctl,
+ .set_termios = mxu1_set_termios,
+ .tiocmget = mxu1_tiocmget,
+ .tiocmset = mxu1_tiocmset,
+ .tiocmiwait = usb_serial_generic_tiocmiwait,
+ .get_icount = usb_serial_generic_get_icount,
+ .break_ctl = mxu1_break,
+ .read_int_callback = mxu1_interrupt_callback,
+};
+
+static struct usb_serial_driver *const serial_drivers[] = {
+ &mxuport11_device, NULL
+};
+
+module_usb_serial_driver(serial_drivers, mxu1_idtable);
+
+MODULE_AUTHOR("Mathieu Othacehe <[email protected]>");
+MODULE_DESCRIPTION("MOXA UPort 11x0 USB to Serial Hub Driver");
+MODULE_LICENSE("GPL");
+MODULE_FIRMWARE("moxa/moxa-1110.fw");
+MODULE_FIRMWARE("moxa/moxa-1130.fw");
+MODULE_FIRMWARE("moxa/moxa-1131.fw");
+MODULE_FIRMWARE("moxa/moxa-1150.fw");
+MODULE_FIRMWARE("moxa/moxa-1151.fw");
--
2.6.3
On Sun, Dec 06, 2015 at 12:29:43PM +0100, Mathieu OTHACEHE wrote:
> Add a driver which supports :
>
> - UPort 1110 : 1 port RS-232 USB to Serial Hub.
> - UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
> - UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
> - UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
> - UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
>
> This driver is based on GPL MOXA driver written by Hen Huang and available
> on MOXA website. The original driver was based on io_ti serial driver.
>
> Signed-off-by: Mathieu OTHACEHE <[email protected]>
> ---
>
> Hi Johan,
>
> Thanks for your patience, here is v5,
Thanks for the update.
The code itself is in a state ready to be merged, but I have some
concerns about the transceiver-mode interface and also a question about
firmware availability.
> +/* Operation modes */
> +#define MXU1_UART_232 0x00
> +#define MXU1_UART_485_RECEIVER_DISABLED 0x01
> +#define MXU1_UART_485_RECEIVER_ENABLED 0x02
These modes correspond to RS-232, RS-485-2W and RS-422/RS-485-4W.
It is known that the TIOCSRS485-interface is not generic enough as it is
essentially limited to switching between full and half-duplex mode.
There has been been discussions about extending it, see for example this
thread from 2011:
https://lkml.kernel.org/r/[email protected]
However, the TIOCSRS485-ioctl might not even be the right interface for
changing transceiver modes, and instead a sysfs-based
usb-serial-specific interface could be more appropriate for example.
This is a can that we've kicked down the road for a very long time now,
and we really need to reach some sort of conclusion on this. There are a
few usb-serial drivers in mainline for devices that supports other modes
than RS232 and there are out-of-tree drivers that have cooked up their
own interfaces (e.g. Moxa).
Before we have resolved this, we could merge this driver without support for
switching modes as we did for mxuport. If you prefer this, then just set
RS232 for 1110 and 1150, pick a good default mode for 1130 and drop the
RS485 ioctls for now.
> +/* Supported operation types */
> +#define MXU1_TYPE_RS232 BIT(0)
> +#define MXU1_TYPE_RS422 BIT(1)
> +#define MXU1_TYPE_RS485 BIT(2)
> +/* Config struct */
> +struct mxu1_uart_config {
> + __be16 wBaudRate;
> + __be16 wFlags;
> + u8 bDataBits;
> + u8 bParity;
> + u8 bStopBits;
> + char cXon;
> + char cXoff;
> + u8 bUartMode;
> +} __packed;
> +static int mxu1_port_probe(struct usb_serial_port *port)
> +{
> + struct mxu1_port *mxport;
> + struct mxu1_device *mxdev;
> + struct urb *urb;
> +
> + mxport = kzalloc(sizeof(struct mxu1_port), GFP_KERNEL);
> + if (!mxport)
> + return -ENOMEM;
> +
> + spin_lock_init(&mxport->spinlock);
> + mutex_init(&mxport->mutex);
> +
> + mxdev = usb_get_serial_data(port->serial);
> +
> + urb = port->interrupt_in_urb;
> + if (!urb) {
> + dev_err(&port->dev, "%s - no interrupt urb\n", __func__);
> + return -EINVAL;
> + }
> +
> + switch (mxdev->mxd_model) {
> + case MXU1_1110_PRODUCT_ID:
> + mxport->uart_types = MXU1_TYPE_RS232;
> + mxport->uart_mode = MXU1_UART_232;
> + break;
> + case MXU1_1130_PRODUCT_ID:
> + case MXU1_1131_PRODUCT_ID:
> + mxport->uart_types = MXU1_TYPE_RS422 | MXU1_TYPE_RS485;
> + mxport->uart_mode = MXU1_UART_485_RECEIVER_DISABLED;
> + break;
> + case MXU1_1150_PRODUCT_ID:
> + case MXU1_1151_PRODUCT_ID:
> + mxport->uart_types =
> + MXU1_TYPE_RS232 | MXU1_TYPE_RS422 | MXU1_TYPE_RS485;
> + mxport->uart_mode = MXU1_UART_232;
> + break;
> + }
> +
> + usb_set_serial_port_data(port, mxport);
> +
> + port->port.closing_wait =
> + msecs_to_jiffies(MXU1_DEFAULT_CLOSING_WAIT * 10);
> + port->port.drain_delay = 1;
> +
> + return 0;
> +}
> +
> +static int mxu1_startup(struct usb_serial *serial)
> +{
> + struct mxu1_device *mxdev;
> + struct usb_device *dev = serial->dev;
> + struct usb_host_interface *cur_altsetting;
> + char fw_name[32];
> + const struct firmware *fw_p = NULL;
> + int err;
> + int status = 0;
> +
> + dev_dbg(&serial->interface->dev, "%s - product 0x%04X, num configurations %d, configuration value %d\n",
> + __func__, le16_to_cpu(dev->descriptor.idProduct),
> + dev->descriptor.bNumConfigurations,
> + dev->actconfig->desc.bConfigurationValue);
> +
> + /* create device structure */
> + mxdev = kzalloc(sizeof(struct mxu1_device), GFP_KERNEL);
> + if (!mxdev)
> + return -ENOMEM;
> +
> + usb_set_serial_data(serial, mxdev);
> +
> + mxdev->mxd_model = le16_to_cpu(dev->descriptor.idProduct);
> +
> + cur_altsetting = serial->interface->cur_altsetting;
> +
> + /* if we have only 1 configuration, download firmware */
> + if (cur_altsetting->desc.bNumEndpoints == 1) {
> +
> + snprintf(fw_name,
> + sizeof(fw_name),
> + "moxa/moxa-%04x.fw",
> + mxdev->mxd_model);
> +
> + err = request_firmware(&fw_p, fw_name, &serial->interface->dev);
> + if (err) {
> + dev_err(&serial->interface->dev, "failed to request firmware: %d\n",
> + err);
> + kfree(mxdev);
> + return err;
> + }
> +
> + err = mxu1_download_firmware(serial, fw_p);
> + if (err) {
> + kfree(mxdev);
> + release_firmware(fw_p);
Please release the firmware before the state container to reverse
allocation.
> + return err;
> + }
> +
> + status = -ENODEV;
> + release_firmware(fw_p);
> + }
> +
> + return status;
> +}
> +static void mxu1_set_termios(struct tty_struct *tty,
> + struct usb_serial_port *port,
> + struct ktermios *old_termios)
> +{
> + struct mxu1_port *mxport = usb_get_serial_port_data(port);
> + struct mxu1_uart_config *config;
> + tcflag_t cflag, iflag;
> + speed_t baud;
> + int status;
> + unsigned int mcr;
> +
> + cflag = tty->termios.c_cflag;
> + iflag = tty->termios.c_iflag;
> +
> + if (old_termios &&
> + !tty_termios_hw_change(&tty->termios, old_termios) &&
> + tty->termios.c_iflag == old_termios->c_iflag) {
> + dev_dbg(&port->dev, "%s - nothing to change\n", __func__);
> + return;
> + }
> +
> + dev_dbg(&port->dev,
> + "%s - clfag %08x, iflag %08x\n", __func__, cflag, iflag);
> +
> + if (old_termios) {
> + dev_dbg(&port->dev, "%s - old clfag %08x, old iflag %08x\n",
> + __func__,
> + old_termios->c_cflag,
> + old_termios->c_iflag);
> + }
> +
> + config = kzalloc(sizeof(*config), GFP_KERNEL);
> + if (!config)
> + return;
> +
> + /* these flags must be set */
> + config->wFlags |= MXU1_UART_ENABLE_MS_INTS;
> + config->wFlags |= MXU1_UART_ENABLE_AUTO_START_DMA;
> + if (mxport->send_break)
> + config->wFlags |= MXU1_UART_SEND_BREAK_SIGNAL;
> + config->bUartMode = mxport->uart_mode;
> +
> + switch (C_CSIZE(tty)) {
> + case CS5:
> + config->bDataBits = MXU1_UART_5_DATA_BITS;
> + break;
> + case CS6:
> + config->bDataBits = MXU1_UART_6_DATA_BITS;
> + break;
> + case CS7:
> + config->bDataBits = MXU1_UART_7_DATA_BITS;
> + break;
> + default:
> + case CS8:
> + config->bDataBits = MXU1_UART_8_DATA_BITS;
> + break;
> + }
> +
> + if (C_PARENB(tty)) {
> + config->wFlags |= MXU1_UART_ENABLE_PARITY_CHECKING;
> + if (C_CMSPAR(tty)) {
> + if (C_PARODD(tty))
> + config->bParity = MXU1_UART_MARK_PARITY;
> + else
> + config->bParity = MXU1_UART_SPACE_PARITY;
> + } else {
> + if (C_PARODD(tty))
> + config->bParity = MXU1_UART_ODD_PARITY;
> + else
> + config->bParity = MXU1_UART_EVEN_PARITY;
> + }
> + } else {
> + config->bParity = MXU1_UART_NO_PARITY;
> + }
> +
> + if (C_CSTOPB(tty))
> + config->bStopBits = MXU1_UART_2_STOP_BITS;
> + else
> + config->bStopBits = MXU1_UART_1_STOP_BITS;
> +
> + if (C_CRTSCTS(tty)) {
> + /* RTS flow control must be off to drop RTS for baud rate B0 */
> + if (C_BAUD(tty) != B0)
> + config->wFlags |= MXU1_UART_ENABLE_RTS_IN;
> + config->wFlags |= MXU1_UART_ENABLE_CTS_OUT;
> + }
> +
> + if (I_IXOFF(tty) || I_IXON(tty)) {
> + config->cXon = START_CHAR(tty);
> + config->cXoff = STOP_CHAR(tty);
> +
> + if (I_IXOFF(tty))
> + config->wFlags |= MXU1_UART_ENABLE_X_IN;
> +
> + if (I_IXON(tty))
> + config->wFlags |= MXU1_UART_ENABLE_X_OUT;
> + }
> +
> + baud = tty_get_baud_rate(tty);
> + if (!baud)
> + baud = 9600;
> + config->wBaudRate = MXU1_BAUD_BASE / baud;
> +
> + dev_dbg(&port->dev, "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n",
> + __func__, baud, config->wBaudRate, config->wFlags,
> + config->bDataBits, config->bParity, config->bStopBits,
> + config->cXon, config->cXoff, config->bUartMode);
> +
> + cpu_to_be16s(&config->wBaudRate);
> + cpu_to_be16s(&config->wFlags);
> +
> + status = mxu1_send_ctrl_data_urb(port->serial, MXU1_SET_CONFIG, 0,
> + MXU1_UART1_PORT, config,
> + sizeof(*config));
> + if (status)
> + dev_err(&port->dev, "cannot set config: %d\n", status);
> +
> + mutex_lock(&mxport->mutex);
> + mcr = mxport->mcr;
> +
> + if (C_BAUD(tty) == B0)
> + mcr &= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
> + else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
> + mcr |= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
> +
> + status = mxu1_set_mcr(port, mcr);
> + if (status)
> + dev_err(&port->dev, "cannot set modem control: %d\n", status);
> + else
> + mxport->mcr = mcr;
> +
> + mutex_unlock(&mxport->mutex);
> +
> + kfree(config);
> +}
> +
> +static int mxu1_ioctl_get_rs485(struct mxu1_port *mxport,
> + struct serial_rs485 __user *rs485)
> +{
> + struct serial_rs485 aux;
> +
> + memset(&aux, 0, sizeof(aux));
> +
> + if (mxport->uart_mode == MXU1_UART_485_RECEIVER_ENABLED)
> + aux.flags = SER_RS485_ENABLED;
With the current ioctl it's not possible to discern RS422 from RS232
mode.
> +
> + if (copy_to_user(rs485, &aux, sizeof(aux)))
> + return -EFAULT;
> +
> + return 0;
> +}
> +
> +static int mxu1_ioctl_set_rs485(struct usb_serial_port *port,
> + struct mxu1_port *mxport,
> + struct serial_rs485 __user *rs485_user)
> +{
> + struct serial_rs485 rs485;
> + int status = 0;
> +
> + if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user)))
> + return -EFAULT;
> +
> + if (mxport->uart_types & (MXU1_TYPE_RS422 | MXU1_TYPE_RS485)) {
> +
> + if (rs485.flags & SER_RS485_ENABLED) {
> + mxport->uart_mode = MXU1_UART_485_RECEIVER_ENABLED;
> + } else {
> + if (mxport->uart_types & MXU1_TYPE_RS232)
> + mxport->uart_mode = MXU1_UART_232;
> + else
> + mxport->uart_mode =
> + MXU1_UART_485_RECEIVER_DISABLED;
> + }
> + } else {
> + dev_err(&port->dev, "RS485 not supported by this device\n");
> + status = -EINVAL;
> + }
And there's currently no way to set RS485-2W for 1150 using this
interface.
> +
> + memset(&rs485, 0, sizeof(rs485));
> + if (mxport->uart_mode & MXU1_UART_485_RECEIVER_ENABLED)
> + rs485.flags = SER_RS485_ENABLED;
> +
> + if (copy_to_user(rs485_user, &rs485, sizeof(rs485)))
> + return -EFAULT;
> +
> + return status;
> +}
> +static int mxu1_open(struct tty_struct *tty, struct usb_serial_port *port)
> +{
> + struct mxu1_port *mxport = usb_get_serial_port_data(port);
> + struct usb_serial *serial = port->serial;
> + struct urb *urb;
> + int status;
> + u16 open_settings;
> +
> + open_settings = (MXU1_PIPE_MODE_CONTINUOUS |
> + MXU1_PIPE_TIMEOUT_ENABLE |
> + (MXU1_TRANSFER_TIMEOUT << 2));
> +
> + mxport->msr = 0;
> +
> + dev_dbg(&port->dev, "%s - start interrupt in urb\n", __func__);
> + urb = port->interrupt_in_urb;
> + status = usb_submit_urb(urb, GFP_KERNEL);
Just use port->interrupt_in_urb directly here and drop the urb pointer.
> + if (status) {
> + dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
> + status);
> + return status;
> + }
> +
> + if (tty)
> + mxu1_set_termios(tty, port, NULL);
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
> + open_settings, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send open command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
> + 0, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send start command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
> + MXU1_PURGE_INPUT, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot clear input buffers: %d\n",
> + __func__, status);
> +
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
> + MXU1_PURGE_OUTPUT, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot clear output buffers: %d\n",
> + __func__, status);
> +
> + goto unlink_int_urb;
> + }
> +
> + /*
> + * reset the data toggle on the bulk endpoints to work around bug in
> + * host controllers where things get out of sync some times
> + */
> + usb_clear_halt(serial->dev, port->write_urb->pipe);
> + usb_clear_halt(serial->dev, port->read_urb->pipe);
> +
> + if (tty)
> + mxu1_set_termios(tty, port, NULL);
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
> + open_settings, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send open command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
> + 0, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send start command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = usb_serial_generic_open(tty, port);
> + if (status) {
> + dev_err(&port->dev, "%s - submit read urb failed: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + return status;
> +
> +unlink_int_urb:
> + usb_kill_urb(port->interrupt_in_urb);
> +
> + return status;
> +}
> +static void mxu1_handle_new_msr(struct usb_serial_port *port,
> + struct mxu1_port *mxport, u8 msr)
Just pass the usb-serial port and use usb_get_serial_port_data to access
the state container.
>+{
> + struct async_icount *icount;
> + unsigned long flags;
> +
> + dev_dbg(&port->dev, "%s - msr 0x%02X\n", __func__, msr);
> +
> + spin_lock_irqsave(&mxport->spinlock, flags);
> + mxport->msr = msr & MXU1_MSR_MASK;
> + spin_unlock_irqrestore(&mxport->spinlock, flags);
> +
> + if (msr & MXU1_MSR_DELTA_MASK) {
> + icount = &port->icount;
> + if (msr & MXU1_MSR_DELTA_CTS)
> + icount->cts++;
> + if (msr & MXU1_MSR_DELTA_DSR)
> + icount->dsr++;
> + if (msr & MXU1_MSR_DELTA_CD)
> + icount->dcd++;
> + if (msr & MXU1_MSR_DELTA_RI)
> + icount->rng++;
> +
> + wake_up_interruptible(&port->port.delta_msr_wait);
> + }
> +}
> +
> +static void mxu1_interrupt_callback(struct urb *urb)
> +{
> + struct usb_serial_port *port = urb->context;
> + struct mxu1_port *mxport;
> + unsigned char *data = urb->transfer_buffer;
> + int length = urb->actual_length;
> + int function;
> + int status;
> + u8 msr;
> +
> + mxport = usb_get_serial_port_data(port);
Then you can drop this too.
> +MODULE_AUTHOR("Mathieu Othacehe <[email protected]>");
> +MODULE_DESCRIPTION("MOXA UPort 11x0 USB to Serial Hub Driver");
> +MODULE_LICENSE("GPL");
> +MODULE_FIRMWARE("moxa/moxa-1110.fw");
> +MODULE_FIRMWARE("moxa/moxa-1130.fw");
> +MODULE_FIRMWARE("moxa/moxa-1131.fw");
> +MODULE_FIRMWARE("moxa/moxa-1150.fw");
> +MODULE_FIRMWARE("moxa/moxa-1151.fw");
Where can I find these firmware images?
Thanks,
Johan
> https://lkml.kernel.org/r/[email protected]
>
> However, the TIOCSRS485-ioctl might not even be the right interface for
> changing transceiver modes, and instead a sysfs-based
> usb-serial-specific interface could be more appropriate for example.
sysfs works out very badly if modes can be configured routinely at
runtime. In particular the sysfs interface is completely disconnected
from the vhangup() and security model of the tty interface.
If its the kind if thing just administratively configured at boot then
it's a great interface, just be careful about who has access to it.
Otherwise the traditional interface for that level of configuration has
probably been termiox, which we do have hooks for but don't really make
much use of.
Alan
On Mon, Dec 28, 2015 at 02:39:44PM +0000, One Thousand Gnomes wrote:
> > https://lkml.kernel.org/r/[email protected]
> >
> > However, the TIOCSRS485-ioctl might not even be the right interface for
> > changing transceiver modes, and instead a sysfs-based
> > usb-serial-specific interface could be more appropriate for example.
>
> sysfs works out very badly if modes can be configured routinely at
> runtime. In particular the sysfs interface is completely disconnected
> from the vhangup() and security model of the tty interface.
>
> If its the kind if thing just administratively configured at boot then
> it's a great interface, just be careful about who has access to it.
I think this is something that you only want to configure once (e.g. at
boot) and before even opening the tty device as this can change the
functions of the pins (e.g. DCD becoming TxD-).
If a generic usb-serial-specific interface for this makes sense, I think
we should simply prevent mode changes while the port is in use.
Johan
Add a driver which supports :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.
Signed-off-by: Mathieu OTHACEHE <[email protected]>
---
Hi Johan,
Here is the v6 of the driver.
I understand the problems with the TIOCSRS485/TIOCGRS485 ioctls in this driver.
For now, I prefer dropping mode switching support from the driver as you suggested.
So UPORT 1110 and 1150 only support RS232 and UPORT 1130 only support RS-485-2W.
If a new interface is developped, I'll restore mode switching code.
About firmware images, I just sent a patch to linux-firmware. Here is the link :
https://lkml.org/lkml/2015/12/28/239
Thanks,
Mathieu
Changes in v2:
* Use generic implementation for read/write code
* Use TIOCSRS485/TIOCGRS485 instead of moxa specific ioctl
* Other problems pointed out by Johan review
Changes in v3:
* Drop unused defines
* Fix style problems
* Remove port identification code since this driver is for one-port devices only
* Fix debug messages
* Use a mutex to protect shadow_mc
* Use usb_serial_generic_open and close
* Other problems pointed out by Johan review
Changes in v4:
* mxu1_startup return -ENODEV on purpose if the firmware was downloaded.
It avoids port_probe to fail since the device is reset.
Changes in v5:
* Drop debug messages
* Drop useless fields from mxu1_port and mxu1_device structures
* Return supported bits to userspace in function mxu1_ioctl_set_rs485
* Other problems pointed out by Johan review
Changes in v6:
* Drop RS422/RS485 ioctl mode switching
* Other problems pointed out by Johan review
drivers/usb/serial/Kconfig | 16 +
drivers/usb/serial/Makefile | 1 +
drivers/usb/serial/mxu11x0.c | 995 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1012 insertions(+)
create mode 100644 drivers/usb/serial/mxu11x0.c
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 56ecb8b..f612dda 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -475,6 +475,22 @@ config USB_SERIAL_MOS7840
To compile this driver as a module, choose M here: the
module will be called mos7840. If unsure, choose N.
+config USB_SERIAL_MXUPORT11
+ tristate "USB Moxa UPORT 11x0 Serial Driver"
+ ---help---
+ Say Y here if you want to use a MOXA UPort 11x0 Serial hub.
+
+ This driver supports:
+
+ - UPort 1110 : 1 port RS-232 USB to Serial Hub.
+ - UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
+ - UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
+ - UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
+ - UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mxu11x0.
+
config USB_SERIAL_MXUPORT
tristate "USB Moxa UPORT Serial Driver"
---help---
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index 349d9df..f3fa5e5 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_USB_SERIAL_METRO) += metro-usb.o
obj-$(CONFIG_USB_SERIAL_MOS7720) += mos7720.o
obj-$(CONFIG_USB_SERIAL_MOS7840) += mos7840.o
obj-$(CONFIG_USB_SERIAL_MXUPORT) += mxuport.o
+obj-$(CONFIG_USB_SERIAL_MXUPORT11) += mxu11x0.o
obj-$(CONFIG_USB_SERIAL_NAVMAN) += navman.o
obj-$(CONFIG_USB_SERIAL_OMNINET) += omninet.o
obj-$(CONFIG_USB_SERIAL_OPTICON) += opticon.o
diff --git a/drivers/usb/serial/mxu11x0.c b/drivers/usb/serial/mxu11x0.c
new file mode 100644
index 0000000..8884ca2
--- /dev/null
+++ b/drivers/usb/serial/mxu11x0.c
@@ -0,0 +1,995 @@
+/*
+ *
+ * USB Moxa UPORT 11x0 Serial Driver
+ *
+ * Copyright (C) 2007 MOXA Technologies Co., Ltd.
+ * Copyright (C) 2015 Mathieu Othacehe <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ *
+ * Supports the following Moxa USB to serial converters:
+ * UPort 1110, 1 port RS-232 USB to Serial Hub.
+ * UPort 1130, 1 port RS-422/485 USB to Serial Hub.
+ * UPort 1130I, 1 port RS-422/485 USB to Serial Hub with isolation
+ * protection.
+ * UPort 1150, 1 port RS-232/422/485 USB to Serial Hub.
+ * UPort 1150I, 1 port RS-232/422/485 USB to Serial Hub with isolation
+ * protection.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/firmware.h>
+#include <linux/jiffies.h>
+#include <linux/serial.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/mutex.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <linux/uaccess.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+
+/* Vendor and product ids */
+#define MXU1_VENDOR_ID 0x110a
+#define MXU1_1110_PRODUCT_ID 0x1110
+#define MXU1_1130_PRODUCT_ID 0x1130
+#define MXU1_1150_PRODUCT_ID 0x1150
+#define MXU1_1151_PRODUCT_ID 0x1151
+#define MXU1_1131_PRODUCT_ID 0x1131
+
+/* Commands */
+#define MXU1_GET_VERSION 0x01
+#define MXU1_GET_PORT_STATUS 0x02
+#define MXU1_GET_PORT_DEV_INFO 0x03
+#define MXU1_GET_CONFIG 0x04
+#define MXU1_SET_CONFIG 0x05
+#define MXU1_OPEN_PORT 0x06
+#define MXU1_CLOSE_PORT 0x07
+#define MXU1_START_PORT 0x08
+#define MXU1_STOP_PORT 0x09
+#define MXU1_TEST_PORT 0x0A
+#define MXU1_PURGE_PORT 0x0B
+#define MXU1_RESET_EXT_DEVICE 0x0C
+#define MXU1_GET_OUTQUEUE 0x0D
+#define MXU1_WRITE_DATA 0x80
+#define MXU1_READ_DATA 0x81
+#define MXU1_REQ_TYPE_CLASS 0x82
+
+/* Module identifiers */
+#define MXU1_I2C_PORT 0x01
+#define MXU1_IEEE1284_PORT 0x02
+#define MXU1_UART1_PORT 0x03
+#define MXU1_UART2_PORT 0x04
+#define MXU1_RAM_PORT 0x05
+
+/* Modem status */
+#define MXU1_MSR_DELTA_CTS 0x01
+#define MXU1_MSR_DELTA_DSR 0x02
+#define MXU1_MSR_DELTA_RI 0x04
+#define MXU1_MSR_DELTA_CD 0x08
+#define MXU1_MSR_CTS 0x10
+#define MXU1_MSR_DSR 0x20
+#define MXU1_MSR_RI 0x40
+#define MXU1_MSR_CD 0x80
+#define MXU1_MSR_DELTA_MASK 0x0F
+#define MXU1_MSR_MASK 0xF0
+
+/* Line status */
+#define MXU1_LSR_OVERRUN_ERROR 0x01
+#define MXU1_LSR_PARITY_ERROR 0x02
+#define MXU1_LSR_FRAMING_ERROR 0x04
+#define MXU1_LSR_BREAK 0x08
+#define MXU1_LSR_ERROR 0x0F
+#define MXU1_LSR_RX_FULL 0x10
+#define MXU1_LSR_TX_EMPTY 0x20
+
+/* Modem control */
+#define MXU1_MCR_LOOP 0x04
+#define MXU1_MCR_DTR 0x10
+#define MXU1_MCR_RTS 0x20
+
+/* Mask settings */
+#define MXU1_UART_ENABLE_RTS_IN 0x0001
+#define MXU1_UART_DISABLE_RTS 0x0002
+#define MXU1_UART_ENABLE_PARITY_CHECKING 0x0008
+#define MXU1_UART_ENABLE_DSR_OUT 0x0010
+#define MXU1_UART_ENABLE_CTS_OUT 0x0020
+#define MXU1_UART_ENABLE_X_OUT 0x0040
+#define MXU1_UART_ENABLE_XA_OUT 0x0080
+#define MXU1_UART_ENABLE_X_IN 0x0100
+#define MXU1_UART_ENABLE_DTR_IN 0x0800
+#define MXU1_UART_DISABLE_DTR 0x1000
+#define MXU1_UART_ENABLE_MS_INTS 0x2000
+#define MXU1_UART_ENABLE_AUTO_START_DMA 0x4000
+#define MXU1_UART_SEND_BREAK_SIGNAL 0x8000
+
+/* Parity */
+#define MXU1_UART_NO_PARITY 0x00
+#define MXU1_UART_ODD_PARITY 0x01
+#define MXU1_UART_EVEN_PARITY 0x02
+#define MXU1_UART_MARK_PARITY 0x03
+#define MXU1_UART_SPACE_PARITY 0x04
+
+/* Stop bits */
+#define MXU1_UART_1_STOP_BITS 0x00
+#define MXU1_UART_1_5_STOP_BITS 0x01
+#define MXU1_UART_2_STOP_BITS 0x02
+
+/* Bits per character */
+#define MXU1_UART_5_DATA_BITS 0x00
+#define MXU1_UART_6_DATA_BITS 0x01
+#define MXU1_UART_7_DATA_BITS 0x02
+#define MXU1_UART_8_DATA_BITS 0x03
+
+/* Operation modes */
+#define MXU1_UART_232 0x00
+#define MXU1_UART_485_RECEIVER_DISABLED 0x01
+#define MXU1_UART_485_RECEIVER_ENABLED 0x02
+
+/* Pipe transfer mode and timeout */
+#define MXU1_PIPE_MODE_CONTINUOUS 0x01
+#define MXU1_PIPE_MODE_MASK 0x03
+#define MXU1_PIPE_TIMEOUT_MASK 0x7C
+#define MXU1_PIPE_TIMEOUT_ENABLE 0x80
+
+/* Config struct */
+struct mxu1_uart_config {
+ __be16 wBaudRate;
+ __be16 wFlags;
+ u8 bDataBits;
+ u8 bParity;
+ u8 bStopBits;
+ char cXon;
+ char cXoff;
+ u8 bUartMode;
+} __packed;
+
+/* Purge modes */
+#define MXU1_PURGE_OUTPUT 0x00
+#define MXU1_PURGE_INPUT 0x80
+
+/* Read/Write data */
+#define MXU1_RW_DATA_ADDR_SFR 0x10
+#define MXU1_RW_DATA_ADDR_IDATA 0x20
+#define MXU1_RW_DATA_ADDR_XDATA 0x30
+#define MXU1_RW_DATA_ADDR_CODE 0x40
+#define MXU1_RW_DATA_ADDR_GPIO 0x50
+#define MXU1_RW_DATA_ADDR_I2C 0x60
+#define MXU1_RW_DATA_ADDR_FLASH 0x70
+#define MXU1_RW_DATA_ADDR_DSP 0x80
+
+#define MXU1_RW_DATA_UNSPECIFIED 0x00
+#define MXU1_RW_DATA_BYTE 0x01
+#define MXU1_RW_DATA_WORD 0x02
+#define MXU1_RW_DATA_DOUBLE_WORD 0x04
+
+struct mxu1_write_data_bytes {
+ u8 bAddrType;
+ u8 bDataType;
+ u8 bDataCounter;
+ __be16 wBaseAddrHi;
+ __be16 wBaseAddrLo;
+ u8 bData[0];
+} __packed;
+
+/* Interrupt codes */
+#define MXU1_CODE_HARDWARE_ERROR 0xFF
+#define MXU1_CODE_DATA_ERROR 0x03
+#define MXU1_CODE_MODEM_STATUS 0x04
+
+static inline int mxu1_get_func_from_code(unsigned char code)
+{
+ return code & 0x0f;
+}
+
+/* Download firmware max packet size */
+#define MXU1_DOWNLOAD_MAX_PACKET_SIZE 64
+
+/* Firmware image header */
+struct mxu1_firmware_header {
+ __le16 wLength;
+ u8 bCheckSum;
+} __packed;
+
+#define MXU1_UART_BASE_ADDR 0xFFA0
+#define MXU1_UART_OFFSET_MCR 0x0004
+
+#define MXU1_BAUD_BASE 923077
+
+#define MXU1_TRANSFER_TIMEOUT 2
+#define MXU1_DOWNLOAD_TIMEOUT 1000
+#define MXU1_DEFAULT_CLOSING_WAIT 4000 /* in .01 secs */
+
+struct mxu1_port {
+ u8 msr;
+ u8 mcr;
+ u8 uart_mode;
+ spinlock_t spinlock; /* Protects msr */
+ struct mutex mutex; /* Protects mcr */
+ bool send_break;
+};
+
+struct mxu1_device {
+ u16 mxd_model;
+};
+
+static const struct usb_device_id mxu1_idtable[] = {
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1110_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1130_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1150_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1151_PRODUCT_ID) },
+ { USB_DEVICE(MXU1_VENDOR_ID, MXU1_1131_PRODUCT_ID) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, mxu1_idtable);
+
+/* Write the given buffer out to the control pipe. */
+static int mxu1_send_ctrl_data_urb(struct usb_serial *serial,
+ u8 request,
+ u16 value, u16 index,
+ void *data, size_t size)
+{
+ int status;
+
+ status = usb_control_msg(serial->dev,
+ usb_sndctrlpipe(serial->dev, 0),
+ request,
+ (USB_DIR_OUT | USB_TYPE_VENDOR |
+ USB_RECIP_DEVICE), value, index,
+ data, size,
+ USB_CTRL_SET_TIMEOUT);
+ if (status < 0) {
+ dev_err(&serial->interface->dev,
+ "%s - usb_control_msg failed: %d\n",
+ __func__, status);
+ return status;
+ }
+
+ if (status != size) {
+ dev_err(&serial->interface->dev,
+ "%s - short write (%d / %zd)\n",
+ __func__, status, size);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/* Send a vendor request without any data */
+static int mxu1_send_ctrl_urb(struct usb_serial *serial,
+ u8 request, u16 value, u16 index)
+{
+ return mxu1_send_ctrl_data_urb(serial, request, value, index,
+ NULL, 0);
+}
+
+static int mxu1_download_firmware(struct usb_serial *serial,
+ const struct firmware *fw_p)
+{
+ int status = 0;
+ int buffer_size;
+ int pos;
+ int len;
+ int done;
+ u8 cs = 0;
+ u8 *buffer;
+ struct usb_device *dev = serial->dev;
+ struct mxu1_firmware_header *header;
+ unsigned int pipe;
+
+ pipe = usb_sndbulkpipe(dev, serial->port[0]->bulk_out_endpointAddress);
+
+ buffer_size = fw_p->size + sizeof(*header);
+ buffer = kmalloc(buffer_size, GFP_KERNEL);
+ if (!buffer)
+ return -ENOMEM;
+
+ memcpy(buffer, fw_p->data, fw_p->size);
+ memset(buffer + fw_p->size, 0xff, buffer_size - fw_p->size);
+
+ for (pos = sizeof(*header); pos < buffer_size; pos++)
+ cs = (u8)(cs + buffer[pos]);
+
+ header = (struct mxu1_firmware_header *)buffer;
+ header->wLength = cpu_to_le16(buffer_size - sizeof(*header));
+ header->bCheckSum = cs;
+
+ dev_dbg(&dev->dev, "%s - downloading firmware\n", __func__);
+
+ for (pos = 0; pos < buffer_size; pos += done) {
+ len = min(buffer_size - pos, MXU1_DOWNLOAD_MAX_PACKET_SIZE);
+
+ status = usb_bulk_msg(dev, pipe, buffer + pos, len, &done,
+ MXU1_DOWNLOAD_TIMEOUT);
+ if (status)
+ break;
+ }
+
+ kfree(buffer);
+
+ if (status) {
+ dev_err(&dev->dev, "failed to download firmware: %d\n", status);
+ return status;
+ }
+
+ msleep_interruptible(100);
+ usb_reset_device(dev);
+
+ dev_dbg(&dev->dev, "%s - download successful\n", __func__);
+
+ return 0;
+}
+
+static int mxu1_port_probe(struct usb_serial_port *port)
+{
+ struct mxu1_port *mxport;
+ struct mxu1_device *mxdev;
+ struct urb *urb;
+
+ mxport = kzalloc(sizeof(struct mxu1_port), GFP_KERNEL);
+ if (!mxport)
+ return -ENOMEM;
+
+ spin_lock_init(&mxport->spinlock);
+ mutex_init(&mxport->mutex);
+
+ mxdev = usb_get_serial_data(port->serial);
+
+ urb = port->interrupt_in_urb;
+ if (!urb) {
+ dev_err(&port->dev, "%s - no interrupt urb\n", __func__);
+ return -EINVAL;
+ }
+
+ switch (mxdev->mxd_model) {
+ case MXU1_1110_PRODUCT_ID:
+ case MXU1_1150_PRODUCT_ID:
+ case MXU1_1151_PRODUCT_ID:
+ mxport->uart_mode = MXU1_UART_232;
+ break;
+ case MXU1_1130_PRODUCT_ID:
+ case MXU1_1131_PRODUCT_ID:
+ mxport->uart_mode = MXU1_UART_485_RECEIVER_DISABLED;
+ break;
+ }
+
+ usb_set_serial_port_data(port, mxport);
+
+ port->port.closing_wait =
+ msecs_to_jiffies(MXU1_DEFAULT_CLOSING_WAIT * 10);
+ port->port.drain_delay = 1;
+
+ return 0;
+}
+
+static int mxu1_startup(struct usb_serial *serial)
+{
+ struct mxu1_device *mxdev;
+ struct usb_device *dev = serial->dev;
+ struct usb_host_interface *cur_altsetting;
+ char fw_name[32];
+ const struct firmware *fw_p = NULL;
+ int err;
+ int status = 0;
+
+ dev_dbg(&serial->interface->dev, "%s - product 0x%04X, num configurations %d, configuration value %d\n",
+ __func__, le16_to_cpu(dev->descriptor.idProduct),
+ dev->descriptor.bNumConfigurations,
+ dev->actconfig->desc.bConfigurationValue);
+
+ /* create device structure */
+ mxdev = kzalloc(sizeof(struct mxu1_device), GFP_KERNEL);
+ if (!mxdev)
+ return -ENOMEM;
+
+ usb_set_serial_data(serial, mxdev);
+
+ mxdev->mxd_model = le16_to_cpu(dev->descriptor.idProduct);
+
+ cur_altsetting = serial->interface->cur_altsetting;
+
+ /* if we have only 1 configuration, download firmware */
+ if (cur_altsetting->desc.bNumEndpoints == 1) {
+
+ snprintf(fw_name,
+ sizeof(fw_name),
+ "moxa/moxa-%04x.fw",
+ mxdev->mxd_model);
+
+ err = request_firmware(&fw_p, fw_name, &serial->interface->dev);
+ if (err) {
+ dev_err(&serial->interface->dev, "failed to request firmware: %d\n",
+ err);
+ kfree(mxdev);
+ return err;
+ }
+
+ err = mxu1_download_firmware(serial, fw_p);
+ if (err) {
+ release_firmware(fw_p);
+ kfree(mxdev);
+ return err;
+ }
+
+ status = -ENODEV;
+ release_firmware(fw_p);
+ }
+
+ return status;
+}
+
+static int mxu1_write_byte(struct usb_serial_port *port, u32 addr,
+ u8 mask, u8 byte)
+{
+ int status;
+ size_t size;
+ struct mxu1_write_data_bytes *data;
+
+ dev_dbg(&port->dev, "%s - addr 0x%08X, mask 0x%02X, byte 0x%02X\n",
+ __func__, addr, mask, byte);
+
+ size = sizeof(struct mxu1_write_data_bytes) + 2;
+ data = kzalloc(size, GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->bAddrType = MXU1_RW_DATA_ADDR_XDATA;
+ data->bDataType = MXU1_RW_DATA_BYTE;
+ data->bDataCounter = 1;
+ data->wBaseAddrHi = cpu_to_be16(addr >> 16);
+ data->wBaseAddrLo = cpu_to_be16(addr);
+ data->bData[0] = mask;
+ data->bData[1] = byte;
+
+ status = mxu1_send_ctrl_data_urb(port->serial, MXU1_WRITE_DATA, 0,
+ MXU1_RAM_PORT, data, size);
+ if (status < 0)
+ dev_err(&port->dev, "%s - failed: %d\n", __func__, status);
+
+ kfree(data);
+
+ return status;
+}
+
+static int mxu1_set_mcr(struct usb_serial_port *port, unsigned int mcr)
+{
+ int status;
+
+ status = mxu1_write_byte(port,
+ MXU1_UART_BASE_ADDR + MXU1_UART_OFFSET_MCR,
+ MXU1_MCR_RTS | MXU1_MCR_DTR | MXU1_MCR_LOOP,
+ mcr);
+ return status;
+}
+
+static void mxu1_set_termios(struct tty_struct *tty,
+ struct usb_serial_port *port,
+ struct ktermios *old_termios)
+{
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ struct mxu1_uart_config *config;
+ tcflag_t cflag, iflag;
+ speed_t baud;
+ int status;
+ unsigned int mcr;
+
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
+
+ if (old_termios &&
+ !tty_termios_hw_change(&tty->termios, old_termios) &&
+ tty->termios.c_iflag == old_termios->c_iflag) {
+ dev_dbg(&port->dev, "%s - nothing to change\n", __func__);
+ return;
+ }
+
+ dev_dbg(&port->dev,
+ "%s - clfag %08x, iflag %08x\n", __func__, cflag, iflag);
+
+ if (old_termios) {
+ dev_dbg(&port->dev, "%s - old clfag %08x, old iflag %08x\n",
+ __func__,
+ old_termios->c_cflag,
+ old_termios->c_iflag);
+ }
+
+ config = kzalloc(sizeof(*config), GFP_KERNEL);
+ if (!config)
+ return;
+
+ /* these flags must be set */
+ config->wFlags |= MXU1_UART_ENABLE_MS_INTS;
+ config->wFlags |= MXU1_UART_ENABLE_AUTO_START_DMA;
+ if (mxport->send_break)
+ config->wFlags |= MXU1_UART_SEND_BREAK_SIGNAL;
+ config->bUartMode = mxport->uart_mode;
+
+ switch (C_CSIZE(tty)) {
+ case CS5:
+ config->bDataBits = MXU1_UART_5_DATA_BITS;
+ break;
+ case CS6:
+ config->bDataBits = MXU1_UART_6_DATA_BITS;
+ break;
+ case CS7:
+ config->bDataBits = MXU1_UART_7_DATA_BITS;
+ break;
+ default:
+ case CS8:
+ config->bDataBits = MXU1_UART_8_DATA_BITS;
+ break;
+ }
+
+ if (C_PARENB(tty)) {
+ config->wFlags |= MXU1_UART_ENABLE_PARITY_CHECKING;
+ if (C_CMSPAR(tty)) {
+ if (C_PARODD(tty))
+ config->bParity = MXU1_UART_MARK_PARITY;
+ else
+ config->bParity = MXU1_UART_SPACE_PARITY;
+ } else {
+ if (C_PARODD(tty))
+ config->bParity = MXU1_UART_ODD_PARITY;
+ else
+ config->bParity = MXU1_UART_EVEN_PARITY;
+ }
+ } else {
+ config->bParity = MXU1_UART_NO_PARITY;
+ }
+
+ if (C_CSTOPB(tty))
+ config->bStopBits = MXU1_UART_2_STOP_BITS;
+ else
+ config->bStopBits = MXU1_UART_1_STOP_BITS;
+
+ if (C_CRTSCTS(tty)) {
+ /* RTS flow control must be off to drop RTS for baud rate B0 */
+ if (C_BAUD(tty) != B0)
+ config->wFlags |= MXU1_UART_ENABLE_RTS_IN;
+ config->wFlags |= MXU1_UART_ENABLE_CTS_OUT;
+ }
+
+ if (I_IXOFF(tty) || I_IXON(tty)) {
+ config->cXon = START_CHAR(tty);
+ config->cXoff = STOP_CHAR(tty);
+
+ if (I_IXOFF(tty))
+ config->wFlags |= MXU1_UART_ENABLE_X_IN;
+
+ if (I_IXON(tty))
+ config->wFlags |= MXU1_UART_ENABLE_X_OUT;
+ }
+
+ baud = tty_get_baud_rate(tty);
+ if (!baud)
+ baud = 9600;
+ config->wBaudRate = MXU1_BAUD_BASE / baud;
+
+ dev_dbg(&port->dev, "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n",
+ __func__, baud, config->wBaudRate, config->wFlags,
+ config->bDataBits, config->bParity, config->bStopBits,
+ config->cXon, config->cXoff, config->bUartMode);
+
+ cpu_to_be16s(&config->wBaudRate);
+ cpu_to_be16s(&config->wFlags);
+
+ status = mxu1_send_ctrl_data_urb(port->serial, MXU1_SET_CONFIG, 0,
+ MXU1_UART1_PORT, config,
+ sizeof(*config));
+ if (status)
+ dev_err(&port->dev, "cannot set config: %d\n", status);
+
+ mutex_lock(&mxport->mutex);
+ mcr = mxport->mcr;
+
+ if (C_BAUD(tty) == B0)
+ mcr &= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
+ else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+ mcr |= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
+
+ status = mxu1_set_mcr(port, mcr);
+ if (status)
+ dev_err(&port->dev, "cannot set modem control: %d\n", status);
+ else
+ mxport->mcr = mcr;
+
+ mutex_unlock(&mxport->mutex);
+
+ kfree(config);
+}
+
+static int mxu1_get_serial_info(struct usb_serial_port *port,
+ struct serial_struct __user *ret_arg)
+{
+ struct serial_struct ret_serial;
+ unsigned cwait;
+
+ if (!ret_arg)
+ return -EFAULT;
+
+ cwait = port->port.closing_wait;
+ if (cwait != ASYNC_CLOSING_WAIT_NONE)
+ cwait = jiffies_to_msecs(cwait) / 10;
+
+ memset(&ret_serial, 0, sizeof(ret_serial));
+
+ ret_serial.type = PORT_16550A;
+ ret_serial.line = port->minor;
+ ret_serial.port = 0;
+ ret_serial.xmit_fifo_size = port->bulk_out_size;
+ ret_serial.baud_base = MXU1_BAUD_BASE;
+ ret_serial.close_delay = 5*HZ;
+ ret_serial.closing_wait = cwait;
+
+ if (copy_to_user(ret_arg, &ret_serial, sizeof(*ret_arg)))
+ return -EFAULT;
+
+ return 0;
+}
+
+
+static int mxu1_set_serial_info(struct usb_serial_port *port,
+ struct serial_struct __user *new_arg)
+{
+ struct serial_struct new_serial;
+ unsigned cwait;
+
+ if (copy_from_user(&new_serial, new_arg, sizeof(new_serial)))
+ return -EFAULT;
+
+ cwait = new_serial.closing_wait;
+ if (cwait != ASYNC_CLOSING_WAIT_NONE)
+ cwait = msecs_to_jiffies(10 * new_serial.closing_wait);
+
+ port->port.closing_wait = cwait;
+
+ return 0;
+}
+
+static int mxu1_ioctl(struct tty_struct *tty,
+ unsigned int cmd, unsigned long arg)
+{
+ struct usb_serial_port *port = tty->driver_data;
+
+ switch (cmd) {
+ case TIOCGSERIAL:
+ return mxu1_get_serial_info(port,
+ (struct serial_struct __user *)arg);
+ case TIOCSSERIAL:
+ return mxu1_set_serial_info(port,
+ (struct serial_struct __user *)arg);
+ }
+
+ return -ENOIOCTLCMD;
+}
+
+static int mxu1_tiocmget(struct tty_struct *tty)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ unsigned int result;
+ unsigned int msr;
+ unsigned int mcr;
+ unsigned long flags;
+
+ mutex_lock(&mxport->mutex);
+ spin_lock_irqsave(&mxport->spinlock, flags);
+
+ msr = mxport->msr;
+ mcr = mxport->mcr;
+
+ spin_unlock_irqrestore(&mxport->spinlock, flags);
+ mutex_unlock(&mxport->mutex);
+
+ result = ((mcr & MXU1_MCR_DTR) ? TIOCM_DTR : 0) |
+ ((mcr & MXU1_MCR_RTS) ? TIOCM_RTS : 0) |
+ ((mcr & MXU1_MCR_LOOP) ? TIOCM_LOOP : 0) |
+ ((msr & MXU1_MSR_CTS) ? TIOCM_CTS : 0) |
+ ((msr & MXU1_MSR_CD) ? TIOCM_CAR : 0) |
+ ((msr & MXU1_MSR_RI) ? TIOCM_RI : 0) |
+ ((msr & MXU1_MSR_DSR) ? TIOCM_DSR : 0);
+
+ dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
+
+ return result;
+}
+
+static int mxu1_tiocmset(struct tty_struct *tty,
+ unsigned int set, unsigned int clear)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ int err;
+ unsigned int mcr;
+
+ mutex_lock(&mxport->mutex);
+ mcr = mxport->mcr;
+
+ if (set & TIOCM_RTS)
+ mcr |= MXU1_MCR_RTS;
+ if (set & TIOCM_DTR)
+ mcr |= MXU1_MCR_DTR;
+ if (set & TIOCM_LOOP)
+ mcr |= MXU1_MCR_LOOP;
+
+ if (clear & TIOCM_RTS)
+ mcr &= ~MXU1_MCR_RTS;
+ if (clear & TIOCM_DTR)
+ mcr &= ~MXU1_MCR_DTR;
+ if (clear & TIOCM_LOOP)
+ mcr &= ~MXU1_MCR_LOOP;
+
+ err = mxu1_set_mcr(port, mcr);
+ if (!err)
+ mxport->mcr = mcr;
+
+ mutex_unlock(&mxport->mutex);
+
+ return err;
+}
+
+static void mxu1_break(struct tty_struct *tty, int break_state)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+
+ if (break_state == -1)
+ mxport->send_break = true;
+ else
+ mxport->send_break = false;
+
+ mxu1_set_termios(tty, port, NULL);
+}
+
+static int mxu1_open(struct tty_struct *tty, struct usb_serial_port *port)
+{
+ struct mxu1_port *mxport = usb_get_serial_port_data(port);
+ struct usb_serial *serial = port->serial;
+ int status;
+ u16 open_settings;
+
+ open_settings = (MXU1_PIPE_MODE_CONTINUOUS |
+ MXU1_PIPE_TIMEOUT_ENABLE |
+ (MXU1_TRANSFER_TIMEOUT << 2));
+
+ mxport->msr = 0;
+
+ dev_dbg(&port->dev, "%s - start interrupt in urb\n", __func__);
+ status = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
+ if (status) {
+ dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
+ status);
+ return status;
+ }
+
+ if (tty)
+ mxu1_set_termios(tty, port, NULL);
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
+ open_settings, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send open command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send start command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
+ MXU1_PURGE_INPUT, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot clear input buffers: %d\n",
+ __func__, status);
+
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
+ MXU1_PURGE_OUTPUT, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot clear output buffers: %d\n",
+ __func__, status);
+
+ goto unlink_int_urb;
+ }
+
+ /*
+ * reset the data toggle on the bulk endpoints to work around bug in
+ * host controllers where things get out of sync some times
+ */
+ usb_clear_halt(serial->dev, port->write_urb->pipe);
+ usb_clear_halt(serial->dev, port->read_urb->pipe);
+
+ if (tty)
+ mxu1_set_termios(tty, port, NULL);
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
+ open_settings, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send open command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status) {
+ dev_err(&port->dev, "%s - cannot send start command: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ status = usb_serial_generic_open(tty, port);
+ if (status) {
+ dev_err(&port->dev, "%s - submit read urb failed: %d\n",
+ __func__, status);
+ goto unlink_int_urb;
+ }
+
+ return status;
+
+unlink_int_urb:
+ usb_kill_urb(port->interrupt_in_urb);
+
+ return status;
+}
+
+static void mxu1_close(struct usb_serial_port *port)
+{
+ int status;
+
+ usb_serial_generic_close(port);
+ usb_kill_urb(port->interrupt_in_urb);
+
+ status = mxu1_send_ctrl_urb(port->serial, MXU1_CLOSE_PORT,
+ 0, MXU1_UART1_PORT);
+ if (status)
+ dev_err(&port->dev, "failed to send close port command: %d\n",
+ status);
+}
+
+static void mxu1_handle_new_msr(struct usb_serial_port *port, u8 msr)
+{
+ struct async_icount *icount;
+ struct mxu1_port *mxport;
+ unsigned long flags;
+
+ dev_dbg(&port->dev, "%s - msr 0x%02X\n", __func__, msr);
+
+ mxport = usb_get_serial_port_data(port);
+
+ spin_lock_irqsave(&mxport->spinlock, flags);
+ mxport->msr = msr & MXU1_MSR_MASK;
+ spin_unlock_irqrestore(&mxport->spinlock, flags);
+
+ if (msr & MXU1_MSR_DELTA_MASK) {
+ icount = &port->icount;
+ if (msr & MXU1_MSR_DELTA_CTS)
+ icount->cts++;
+ if (msr & MXU1_MSR_DELTA_DSR)
+ icount->dsr++;
+ if (msr & MXU1_MSR_DELTA_CD)
+ icount->dcd++;
+ if (msr & MXU1_MSR_DELTA_RI)
+ icount->rng++;
+
+ wake_up_interruptible(&port->port.delta_msr_wait);
+ }
+}
+
+static void mxu1_interrupt_callback(struct urb *urb)
+{
+ struct usb_serial_port *port = urb->context;
+ unsigned char *data = urb->transfer_buffer;
+ int length = urb->actual_length;
+ int function;
+ int status;
+ u8 msr;
+
+ switch (urb->status) {
+ case 0:
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ dev_dbg(&port->dev, "%s - urb shutting down: %d\n",
+ __func__, urb->status);
+ return;
+ default:
+ dev_dbg(&port->dev, "%s - nonzero urb status: %d\n",
+ __func__, urb->status);
+ goto exit;
+ }
+
+ if (length != 2) {
+ dev_dbg(&port->dev, "%s - bad packet size: %d\n",
+ __func__, length);
+ goto exit;
+ }
+
+ if (data[0] == MXU1_CODE_HARDWARE_ERROR) {
+ dev_err(&port->dev, "%s - hardware error: %d\n",
+ __func__, data[1]);
+ goto exit;
+ }
+
+ function = mxu1_get_func_from_code(data[0]);
+
+ dev_dbg(&port->dev, "%s - function %d, data 0x%02X\n",
+ __func__, function, data[1]);
+
+ switch (function) {
+ case MXU1_CODE_DATA_ERROR:
+ dev_dbg(&port->dev, "%s - DATA ERROR, data 0x%02X\n",
+ __func__, data[1]);
+ break;
+
+ case MXU1_CODE_MODEM_STATUS:
+ msr = data[1];
+ mxu1_handle_new_msr(port, msr);
+ break;
+
+ default:
+ dev_err(&port->dev, "%s - unknown interrupt code: 0x%02X\n",
+ __func__, data[1]);
+ break;
+ }
+
+exit:
+ status = usb_submit_urb(urb, GFP_ATOMIC);
+ if (status)
+ dev_err(&port->dev, "resubmit interrupt urb failed: %d\n",
+ status);
+}
+
+static struct usb_serial_driver mxuport11_device = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "mxuport11",
+ },
+ .description = "MOXA UPort 11x0",
+ .id_table = mxu1_idtable,
+ .num_ports = 1,
+ .port_probe = mxu1_port_probe,
+ .attach = mxu1_startup,
+ .open = mxu1_open,
+ .close = mxu1_close,
+ .ioctl = mxu1_ioctl,
+ .set_termios = mxu1_set_termios,
+ .tiocmget = mxu1_tiocmget,
+ .tiocmset = mxu1_tiocmset,
+ .tiocmiwait = usb_serial_generic_tiocmiwait,
+ .get_icount = usb_serial_generic_get_icount,
+ .break_ctl = mxu1_break,
+ .read_int_callback = mxu1_interrupt_callback,
+};
+
+static struct usb_serial_driver *const serial_drivers[] = {
+ &mxuport11_device, NULL
+};
+
+module_usb_serial_driver(serial_drivers, mxu1_idtable);
+
+MODULE_AUTHOR("Mathieu Othacehe <[email protected]>");
+MODULE_DESCRIPTION("MOXA UPort 11x0 USB to Serial Hub Driver");
+MODULE_LICENSE("GPL");
+MODULE_FIRMWARE("moxa/moxa-1110.fw");
+MODULE_FIRMWARE("moxa/moxa-1130.fw");
+MODULE_FIRMWARE("moxa/moxa-1131.fw");
+MODULE_FIRMWARE("moxa/moxa-1150.fw");
+MODULE_FIRMWARE("moxa/moxa-1151.fw");
--
2.6.4
On Mon, Dec 28, 2015 at 09:21:25PM +0100, Mathieu OTHACEHE wrote:
> Add a driver which supports :
>
> - UPort 1110 : 1 port RS-232 USB to Serial Hub.
> - UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
> - UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
> - UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
> - UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
>
> This driver is based on GPL MOXA driver written by Hen Huang and available
> on MOXA website. The original driver was based on io_ti serial driver.
>
> Signed-off-by: Mathieu OTHACEHE <[email protected]>
> ---
>
> Hi Johan,
>
> Here is the v6 of the driver.
>
> I understand the problems with the TIOCSRS485/TIOCGRS485 ioctls in
> this driver.
> For now, I prefer dropping mode switching support from the driver as
> you suggested.
>
> So UPORT 1110 and 1150 only support RS232 and UPORT 1130 only support
> RS-485-2W.
> If a new interface is developped, I'll restore mode switching code.
Sounds good.
> About firmware images, I just sent a patch to linux-firmware. Here is the link :
> https://lkml.org/lkml/2015/12/28/239
Thanks, I've done some quick tests using a 1150 now. When looking
through the code one last time I found a few issues that I fixed up. I'll
submit patches for these to the USB list.
But there are couple of things you could consider to do as follow ups as
well. Details below.
> +static int mxu1_port_probe(struct usb_serial_port *port)
> +{
> + struct mxu1_port *mxport;
> + struct mxu1_device *mxdev;
> + struct urb *urb;
> +
> + mxport = kzalloc(sizeof(struct mxu1_port), GFP_KERNEL);
> + if (!mxport)
> + return -ENOMEM;
> +
> + spin_lock_init(&mxport->spinlock);
> + mutex_init(&mxport->mutex);
> +
> + mxdev = usb_get_serial_data(port->serial);
> +
> + urb = port->interrupt_in_urb;
> + if (!urb) {
You are leaking the port private data here (fixed).
> + dev_err(&port->dev, "%s - no interrupt urb\n", __func__);
> + return -EINVAL;
> + }
> +
> + switch (mxdev->mxd_model) {
> + case MXU1_1110_PRODUCT_ID:
> + case MXU1_1150_PRODUCT_ID:
> + case MXU1_1151_PRODUCT_ID:
> + mxport->uart_mode = MXU1_UART_232;
> + break;
> + case MXU1_1130_PRODUCT_ID:
> + case MXU1_1131_PRODUCT_ID:
> + mxport->uart_mode = MXU1_UART_485_RECEIVER_DISABLED;
> + break;
> + }
> +
> + usb_set_serial_port_data(port, mxport);
> +
> + port->port.closing_wait =
> + msecs_to_jiffies(MXU1_DEFAULT_CLOSING_WAIT * 10);
> + port->port.drain_delay = 1;
> +
> + return 0;
> +}
> +
> +static int mxu1_startup(struct usb_serial *serial)
> +{
> + struct mxu1_device *mxdev;
> + struct usb_device *dev = serial->dev;
> + struct usb_host_interface *cur_altsetting;
> + char fw_name[32];
> + const struct firmware *fw_p = NULL;
> + int err;
> + int status = 0;
> +
> + dev_dbg(&serial->interface->dev, "%s - product 0x%04X, num configurations %d, configuration value %d\n",
> + __func__, le16_to_cpu(dev->descriptor.idProduct),
> + dev->descriptor.bNumConfigurations,
> + dev->actconfig->desc.bConfigurationValue);
> +
> + /* create device structure */
> + mxdev = kzalloc(sizeof(struct mxu1_device), GFP_KERNEL);
> + if (!mxdev)
> + return -ENOMEM;
> +
> + usb_set_serial_data(serial, mxdev);
> +
> + mxdev->mxd_model = le16_to_cpu(dev->descriptor.idProduct);
> +
> + cur_altsetting = serial->interface->cur_altsetting;
> +
> + /* if we have only 1 configuration, download firmware */
> + if (cur_altsetting->desc.bNumEndpoints == 1) {
> +
> + snprintf(fw_name,
> + sizeof(fw_name),
> + "moxa/moxa-%04x.fw",
> + mxdev->mxd_model);
> +
> + err = request_firmware(&fw_p, fw_name, &serial->interface->dev);
> + if (err) {
> + dev_err(&serial->interface->dev, "failed to request firmware: %d\n",
> + err);
> + kfree(mxdev);
> + return err;
> + }
> +
> + err = mxu1_download_firmware(serial, fw_p);
> + if (err) {
> + release_firmware(fw_p);
> + kfree(mxdev);
> + return err;
> + }
> +
> + status = -ENODEV;
> + release_firmware(fw_p);
And you're leaking the interface private data here as well (also fixed).
What you could consider doing as a follow up it so move both the
interrupt-in urb test in port_probe and the firmware download to a new
probe callback. That way you avoid the unnecessary memory allocations
done by core before attach is called, and you can verify and refuse to
bind to a device in case the expected endpoints are missing.
> + }
> +
> + return status;
> +}
> + if (C_BAUD(tty) == B0)
> + mcr &= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
> + else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
> + mcr |= ~(MXU1_MCR_DTR | MXU1_MCR_RTS);
This should have been
mcr |= MXU1_MCR_DTR | MXU1_MCR_RTS;
Also fixed.
> +static int mxu1_open(struct tty_struct *tty, struct usb_serial_port *port)
> +{
> + struct mxu1_port *mxport = usb_get_serial_port_data(port);
> + struct usb_serial *serial = port->serial;
> + int status;
> + u16 open_settings;
> +
> + open_settings = (MXU1_PIPE_MODE_CONTINUOUS |
> + MXU1_PIPE_TIMEOUT_ENABLE |
> + (MXU1_TRANSFER_TIMEOUT << 2));
> +
> + mxport->msr = 0;
> +
> + dev_dbg(&port->dev, "%s - start interrupt in urb\n", __func__);
> + status = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
> + if (status) {
> + dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
> + status);
> + return status;
> + }
> +
> + if (tty)
> + mxu1_set_termios(tty, port, NULL);
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
> + open_settings, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send open command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
> + 0, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send start command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
> + MXU1_PURGE_INPUT, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot clear input buffers: %d\n",
> + __func__, status);
> +
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_PURGE_PORT,
> + MXU1_PURGE_OUTPUT, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot clear output buffers: %d\n",
> + __func__, status);
> +
> + goto unlink_int_urb;
> + }
> +
> + /*
> + * reset the data toggle on the bulk endpoints to work around bug in
> + * host controllers where things get out of sync some times
> + */
> + usb_clear_halt(serial->dev, port->write_urb->pipe);
> + usb_clear_halt(serial->dev, port->read_urb->pipe);
> +
> + if (tty)
> + mxu1_set_termios(tty, port, NULL);
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_OPEN_PORT,
> + open_settings, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send open command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + status = mxu1_send_ctrl_urb(serial, MXU1_START_PORT,
> + 0, MXU1_UART1_PORT);
> + if (status) {
> + dev_err(&port->dev, "%s - cannot send start command: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
I noticed that you send OPEN and START twice during probe -- is that
really necessary?
> + status = usb_serial_generic_open(tty, port);
> + if (status) {
> + dev_err(&port->dev, "%s - submit read urb failed: %d\n",
> + __func__, status);
> + goto unlink_int_urb;
> + }
> +
> + return status;
> +
> +unlink_int_urb:
> + usb_kill_urb(port->interrupt_in_urb);
> +
> + return status;
> +}
> +
> +static void mxu1_close(struct usb_serial_port *port)
> +{
> + int status;
> +
> + usb_serial_generic_close(port);
> + usb_kill_urb(port->interrupt_in_urb);
> +
> + status = mxu1_send_ctrl_urb(port->serial, MXU1_CLOSE_PORT,
> + 0, MXU1_UART1_PORT);
> + if (status)
> + dev_err(&port->dev, "failed to send close port command: %d\n",
> + status);
And should there not be a matching STOP request at close?
> +static struct usb_serial_driver mxuport11_device = {
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = "mxuport11",
I also decided to rename the usb-serial driver mxu11x0 to match the
module and USB driver name.
I have applied the patch now and will post my fixes and a couple of
clean ups to the list.
Thanks,
Johan