This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
processor module data that is shared with 'omap3-evm-37xx.dts'. A new
common file for processor module data is introduced to help facilitate
the updated OMAP3530 support.
Derald D. Woods (2):
ARM: dts: omap3-evm-37xx: Add common processor module support
ARM: dts: omap3-evm: Add OMAP3530 specific device tree processor data
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +--------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 214 ++++++++++++++++++++++
arch/arm/boot/dts/omap3-evm.dts | 76 +++++++-
3 files changed, 287 insertions(+), 212 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
--
2.14.1
This commit allows OMAP3530 variants to use common data that is
available in 'omap3-evm-processor-common.dtsi'. It adds proper pinmux
macros for 'omap3_pmx_core2' on OMAP3430. The Micron NAND chip is also
added for the TMDSEVM3530 processor module.
---
arch/arm/boot/dts/omap3-evm.dts | 76 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 72 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 99b2bfcd1059..21a3b88aef0c 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -9,13 +9,81 @@
#include "omap34xx.dtsi"
#include "omap3-evm-common.dtsi"
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP35XX EVM (TMDSEVM3530)";
- compatible = "ti,omap3-evm", "ti,omap3";
+ compatible = "ti,omap3-evm", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+
+ ehci_phy_pins: pinmux_ehci_phy_pins {
+ pinctrl-single,pins = <
+
+ /* EHCI PHY reset GPIO etk_d7.gpio_21 */
+ OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
+
+ /* EHCI VBUS etk_d8.gpio_22 */
+ OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+
+ /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d15.hsusb2_data1 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+};
+
+&gpmc {
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ linux,mtd-name= "micron,mt29f2g16abdhc";
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
};
};
--
2.14.1
This commit moves common OMAP3-EVM processor module device tree data
to a separate include file. This will allow for 'omap3-evm.dts' to use
device tree data that is unique to the OMAP3530 version of the
processor module, while making use of the work already done for the
'omap3-evm-37xx.dts'.
---
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +--------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 214 ++++++++++++++++++++++
2 files changed, 215 insertions(+), 208 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
index c963b31ec3b3..5a4ba0aea447 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -9,146 +9,11 @@
#include "omap36xx.dtsi"
#include "omap3-evm-common.dtsi"
-
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP37XX EVM (TMDSEVM3730)";
compatible = "ti,omap3-evm-37xx", "ti,omap3630", "ti,omap3";
-
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
- };
-
- wl12xx_vmmc: wl12xx_vmmc {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_gpio>;
- };
-};
-
-&dss {
- pinctrl-names = "default";
- pinctrl-0 = <
- &dss_dpi_pins1
- &dss_dpi_pins2
- >;
-};
-
-&hsusb2_phy {
- pinctrl-names = "default";
- pinctrl-0 = <&ehci_phy_pins>;
-};
-
-&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
-
- dss_dpi_pins1: pinmux_dss_dpi_pins2 {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
- OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
- OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
- OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
-
- OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
- OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
- OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
- OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
- OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
- OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
- OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
- OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
- OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
- OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
- OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
-
- OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
- OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
- OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
- OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
- OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
- OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
- >;
- };
-
- mmc1_pins: pinmux_mmc1_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
- OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
- OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
- OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
- OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
- OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
- OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
- OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
- OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
- OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
- >;
- };
-
- /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
- mmc2_pins: pinmux_mmc2_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
- OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
- OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
- OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
- OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
- OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
- >;
- };
-
- /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
- on_board_gpio_61: pinmux_ehci_port_select_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_pins: pinmux_hsusb2_pins {
- pinctrl-single,pins = <
-
- /* mcspi1_cs3.hsusb2_data2 */
- OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_clk.hsusb2_data7 */
- OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_simo.hsusb2_data4 */
- OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_somi.hsusb2_data5 */
- OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs0.hsusb2_data6 */
- OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs1.hsusb2_data3 */
- OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-
- wl12xx_gpio: pinmux_wl12xx_gpio {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
- OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
- >;
- };
-
- smsc911x_pins: pinmux_smsc911x_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
- >;
- };
};
&omap3_pmx_core2 {
@@ -191,74 +56,7 @@
};
};
-&omap3_pmx_wkup {
- dss_dpi_pins2: pinmux_dss_dpi_pins1 {
- pinctrl-single,pins = <
- OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
- OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
- OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
- OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
- OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
- OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
- >;
- };
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&uart1 {
- interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-&uart2 {
- interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
-};
-
-&uart3 {
- interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
-};
-
-/*
- * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
- * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
- */
-&gpio2 {
- en_usb2_port {
- gpio-hog;
- gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
- output-low;
- line-name = "enable usb2 port";
- };
-};
-
-/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
-&twl_gpio {
- en_on_board_gpio_61 {
- gpio-hog;
- gpios = <2 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "en_hsusb2_clk";
- };
-};
-
&gpmc {
- ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
- <5 0 0x2c000000 0x01000000>;
-
nand@0,0 {
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
@@ -309,9 +107,4 @@
reg = <0x780000 0x1f880000>;
};
};
-
- ethernet@gpmc {
- pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
- };
};
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
new file mode 100644
index 000000000000..c1fb6ecd5aff
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
@@ -0,0 +1,214 @@
+/*
+ * Common support for omap3 EVM 35xx/37xx processor modules
+ */
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ };
+};
+
+&dss {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+};
+
+&hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehci_phy_pins>;
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
+ on_board_gpio_61: pinmux_ehci_port_select_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+
+ /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
+ >;
+ };
+
+ smsc911x_pins: pinmux_smsc911x_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+&uart2 {
+ interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+};
+
+&uart3 {
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+/*
+ * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
+ * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
+ */
+&gpio2 {
+ en_usb2_port {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
+ output-low;
+ line-name = "enable usb2 port";
+ };
+};
+
+/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
+&twl_gpio {
+ en_on_board_gpio_61 {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "en_hsusb2_clk";
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
+ <5 0 0x2c000000 0x01000000>; /* CS5: 16MB for LAN9220 */
+
+ ethernet@gpmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc911x_pins>;
+ };
+};
--
2.14.1
* Derald D. Woods <[email protected]> [170902 17:39]:
> This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
> processor module data that is shared with 'omap3-evm-37xx.dts'. A new
> common file for processor module data is introduced to help facilitate
> the updated OMAP3530 support.
Hey that's great, I only have the 37xx variant. Looks OK to me
based on a quick look, will take a closer look after the merge
window closes.
Regards,
Tony
This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
processor module data that is shared with 'omap3-evm-37xx.dts'. A new
common file for processor module data is introduced to help facilitate
the updated OMAP3530 support.
Changes in v2
-------------
- Pull in change from linux-next
(ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc")
- Add compatible and supply fix for LCD panel
- Add supply references for DSS
- Add "Signed-off-by" for each patch
Derald D. Woods (4):
ARM: dts: omap3-evm-37xx: Add common processor module support
ARM: dts: omap3-evm: Add OMAP3530 specific device tree processor data
ARM: dts: omap3: Fix Sharp LS037V7DW01 compatible string and envdd
supply
ARM: dts: omap3-evm: Add DSS {vdds_dsi,vdda_video}-supply references
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +-------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 216 +++++++++++++++++++++
arch/arm/boot/dts/omap3-evm.dts | 76 +++++++-
.../boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 3 +-
4 files changed, 291 insertions(+), 213 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
--
2.14.1
This commit moves common OMAP3-EVM processor module device tree data
to a separate include file. This will allow for 'omap3-evm.dts' to use
device tree data that is unique to the OMAP3530 version of the
processor module, while making use of the work already done for the
'omap3-evm-37xx.dts'.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +--------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 214 ++++++++++++++++++++++
2 files changed, 215 insertions(+), 208 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
index c963b31ec3b3..5a4ba0aea447 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -9,146 +9,11 @@
#include "omap36xx.dtsi"
#include "omap3-evm-common.dtsi"
-
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP37XX EVM (TMDSEVM3730)";
compatible = "ti,omap3-evm-37xx", "ti,omap3630", "ti,omap3";
-
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
- };
-
- wl12xx_vmmc: wl12xx_vmmc {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_gpio>;
- };
-};
-
-&dss {
- pinctrl-names = "default";
- pinctrl-0 = <
- &dss_dpi_pins1
- &dss_dpi_pins2
- >;
-};
-
-&hsusb2_phy {
- pinctrl-names = "default";
- pinctrl-0 = <&ehci_phy_pins>;
-};
-
-&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
-
- dss_dpi_pins1: pinmux_dss_dpi_pins2 {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
- OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
- OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
- OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
-
- OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
- OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
- OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
- OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
- OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
- OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
- OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
- OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
- OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
- OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
- OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
-
- OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
- OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
- OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
- OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
- OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
- OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
- >;
- };
-
- mmc1_pins: pinmux_mmc1_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
- OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
- OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
- OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
- OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
- OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
- OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
- OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
- OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
- OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
- >;
- };
-
- /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
- mmc2_pins: pinmux_mmc2_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
- OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
- OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
- OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
- OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
- OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
- >;
- };
-
- /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
- on_board_gpio_61: pinmux_ehci_port_select_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_pins: pinmux_hsusb2_pins {
- pinctrl-single,pins = <
-
- /* mcspi1_cs3.hsusb2_data2 */
- OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_clk.hsusb2_data7 */
- OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_simo.hsusb2_data4 */
- OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_somi.hsusb2_data5 */
- OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs0.hsusb2_data6 */
- OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs1.hsusb2_data3 */
- OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-
- wl12xx_gpio: pinmux_wl12xx_gpio {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
- OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
- >;
- };
-
- smsc911x_pins: pinmux_smsc911x_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
- >;
- };
};
&omap3_pmx_core2 {
@@ -191,74 +56,7 @@
};
};
-&omap3_pmx_wkup {
- dss_dpi_pins2: pinmux_dss_dpi_pins1 {
- pinctrl-single,pins = <
- OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
- OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
- OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
- OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
- OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
- OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
- >;
- };
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&uart1 {
- interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-&uart2 {
- interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
-};
-
-&uart3 {
- interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
-};
-
-/*
- * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
- * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
- */
-&gpio2 {
- en_usb2_port {
- gpio-hog;
- gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
- output-low;
- line-name = "enable usb2 port";
- };
-};
-
-/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
-&twl_gpio {
- en_on_board_gpio_61 {
- gpio-hog;
- gpios = <2 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "en_hsusb2_clk";
- };
-};
-
&gpmc {
- ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
- <5 0 0x2c000000 0x01000000>;
-
nand@0,0 {
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
@@ -309,9 +107,4 @@
reg = <0x780000 0x1f880000>;
};
};
-
- ethernet@gpmc {
- pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
- };
};
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
new file mode 100644
index 000000000000..c1fb6ecd5aff
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
@@ -0,0 +1,214 @@
+/*
+ * Common support for omap3 EVM 35xx/37xx processor modules
+ */
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ };
+};
+
+&dss {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+};
+
+&hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehci_phy_pins>;
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
+ on_board_gpio_61: pinmux_ehci_port_select_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+
+ /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
+ >;
+ };
+
+ smsc911x_pins: pinmux_smsc911x_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+&uart2 {
+ interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+};
+
+&uart3 {
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+/*
+ * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
+ * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
+ */
+&gpio2 {
+ en_usb2_port {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
+ output-low;
+ line-name = "enable usb2 port";
+ };
+};
+
+/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
+&twl_gpio {
+ en_on_board_gpio_61 {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "en_hsusb2_clk";
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
+ <5 0 0x2c000000 0x01000000>; /* CS5: 16MB for LAN9220 */
+
+ ethernet@gpmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc911x_pins>;
+ };
+};
--
2.14.1
The Sharp panel driver and regulator are now selected properly. This
commit eliminates a dummy regulator assignment.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
index 157345bb8e79..15f73e5adfdf 100644
--- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
+++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
@@ -26,9 +26,10 @@
};
lcd0: display {
- compatible = "sharp,ls037v7dw01";
+ compatible = "omapdss,sharp,ls037v7dw01";
label = "lcd";
power-supply = <&lcd_3v3>;
+ envdd-supply = <&lcd_3v3>;
port {
lcd_in: endpoint {
--
2.14.1
This commit eliminates two dummy regulator assignments.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
index c1fb6ecd5aff..ce7f42f9448c 100644
--- a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
+++ b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
@@ -15,6 +15,8 @@
};
&dss {
+ vdds_dsi-supply = <&vpll2>;
+ vdda_video-supply = <&lcd_3v3>;
pinctrl-names = "default";
pinctrl-0 = <
&dss_dpi_pins1
--
2.14.1
This commit allows OMAP3530 variants to use common data that is
available in 'omap3-evm-processor-common.dtsi'. It adds proper pinmux
macros for 'omap3_pmx_core2' on OMAP3430. The Micron NAND chip is also
added for the TMDSEVM3530 processor module.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm.dts | 76 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 72 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 99b2bfcd1059..21a3b88aef0c 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -9,13 +9,81 @@
#include "omap34xx.dtsi"
#include "omap3-evm-common.dtsi"
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP35XX EVM (TMDSEVM3530)";
- compatible = "ti,omap3-evm", "ti,omap3";
+ compatible = "ti,omap3-evm", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+
+ ehci_phy_pins: pinmux_ehci_phy_pins {
+ pinctrl-single,pins = <
+
+ /* EHCI PHY reset GPIO etk_d7.gpio_21 */
+ OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
+
+ /* EHCI VBUS etk_d8.gpio_22 */
+ OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+
+ /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d15.hsusb2_data1 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+};
+
+&gpmc {
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ linux,mtd-name= "micron,mt29f2g16abdhc";
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
};
};
--
2.14.1
* Derald D. Woods <[email protected]> [170911 20:48]:
> The Sharp panel driver and regulator are now selected properly. This
> commit eliminates a dummy regulator assignment.
>
> Signed-off-by: Derald D. Woods <[email protected]>
>
> ---
> arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> index 157345bb8e79..15f73e5adfdf 100644
> --- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> +++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> @@ -26,9 +26,10 @@
> };
>
> lcd0: display {
> - compatible = "sharp,ls037v7dw01";
> + compatible = "omapdss,sharp,ls037v7dw01";
Is this change needed? I think the driver automatically matches
even with the "omapdss" part missing?
If it's needed, can you please update the description for why
it's needed.
Regards,
Tony
On Tue, Sep 12, 2017 at 07:34:46AM -0700, Tony Lindgren wrote:
> * Derald D. Woods <[email protected]> [170911 20:48]:
> > The Sharp panel driver and regulator are now selected properly. This
> > commit eliminates a dummy regulator assignment.
> >
> > Signed-off-by: Derald D. Woods <[email protected]>
> >
> > ---
> > arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 3 ++-
> > 1 file changed, 2 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> > index 157345bb8e79..15f73e5adfdf 100644
> > --- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> > +++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
> > @@ -26,9 +26,10 @@
> > };
> >
> > lcd0: display {
> > - compatible = "sharp,ls037v7dw01";
> > + compatible = "omapdss,sharp,ls037v7dw01";
>
> Is this change needed? I think the driver automatically matches
> even with the "omapdss" part missing?
>
I will check tonight. It is likely something I added when trying various
DSS Kconfig options. I will keep my configuration unchanged and remove
the compatible line change above. If it is just noise, I will send 'v3'
with just 'envdd' supply addition.
Derald
> If it's needed, can you please update the description for why
> it's needed.
>
> Regards,
>
> Tony
This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
processor module data that is shared with 'omap3-evm-37xx.dts'. A new
common file for processor module data is introduced to help facilitate
the updated OMAP3530 support.
Changes in v3
-------------
- Drop unnecessary compatible string change to Sharp LCD panel
Changes in v2
-------------
- Pull in change from linux-next
(ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc")
- Add compatible and supply fix for LCD panel
- Add supply references for DSS
- Add "Signed-off-by" for each patch
Derald D. Woods (4):
ARM: dts: omap3-evm-37xx: Add common processor module support
ARM: dts: omap3-evm: Add OMAP3530 specific device tree processor data
ARM: dts: omap3: Add Sharp LS037V7DW01 'envdd' supply
ARM: dts: omap3-evm: Add DSS {vdds_dsi,vdda_video}-supply references
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +-------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 216 +++++++++++++++++++++
arch/arm/boot/dts/omap3-evm.dts | 76 +++++++-
.../boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 1 +
4 files changed, 290 insertions(+), 212 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
--
2.14.1
This commit moves common OMAP3-EVM processor module device tree data
to a separate include file. This will allow for 'omap3-evm.dts' to use
device tree data that is unique to the OMAP3530 version of the
processor module, while making use of the work already done for the
'omap3-evm-37xx.dts'.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +--------------------
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 214 ++++++++++++++++++++++
2 files changed, 215 insertions(+), 208 deletions(-)
create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
index c963b31ec3b3..5a4ba0aea447 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -9,146 +9,11 @@
#include "omap36xx.dtsi"
#include "omap3-evm-common.dtsi"
-
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP37XX EVM (TMDSEVM3730)";
compatible = "ti,omap3-evm-37xx", "ti,omap3630", "ti,omap3";
-
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
- };
-
- wl12xx_vmmc: wl12xx_vmmc {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_gpio>;
- };
-};
-
-&dss {
- pinctrl-names = "default";
- pinctrl-0 = <
- &dss_dpi_pins1
- &dss_dpi_pins2
- >;
-};
-
-&hsusb2_phy {
- pinctrl-names = "default";
- pinctrl-0 = <&ehci_phy_pins>;
-};
-
-&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
-
- dss_dpi_pins1: pinmux_dss_dpi_pins2 {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
- OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
- OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
- OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
-
- OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
- OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
- OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
- OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
- OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
- OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
- OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
- OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
- OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
- OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
- OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
-
- OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
- OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
- OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
- OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
- OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
- OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
- >;
- };
-
- mmc1_pins: pinmux_mmc1_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
- OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
- OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
- OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
- OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
- OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
- OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
- OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
- OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
- OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
- >;
- };
-
- /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
- mmc2_pins: pinmux_mmc2_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
- OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
- OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
- OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
- OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
- OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
- >;
- };
-
- /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
- on_board_gpio_61: pinmux_ehci_port_select_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_pins: pinmux_hsusb2_pins {
- pinctrl-single,pins = <
-
- /* mcspi1_cs3.hsusb2_data2 */
- OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_clk.hsusb2_data7 */
- OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_simo.hsusb2_data4 */
- OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_somi.hsusb2_data5 */
- OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs0.hsusb2_data6 */
- OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs1.hsusb2_data3 */
- OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-
- wl12xx_gpio: pinmux_wl12xx_gpio {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
- OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
- >;
- };
-
- smsc911x_pins: pinmux_smsc911x_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
- >;
- };
};
&omap3_pmx_core2 {
@@ -191,74 +56,7 @@
};
};
-&omap3_pmx_wkup {
- dss_dpi_pins2: pinmux_dss_dpi_pins1 {
- pinctrl-single,pins = <
- OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
- OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
- OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
- OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
- OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
- OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
- >;
- };
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&uart1 {
- interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-&uart2 {
- interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
-};
-
-&uart3 {
- interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
-};
-
-/*
- * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
- * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
- */
-&gpio2 {
- en_usb2_port {
- gpio-hog;
- gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
- output-low;
- line-name = "enable usb2 port";
- };
-};
-
-/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
-&twl_gpio {
- en_on_board_gpio_61 {
- gpio-hog;
- gpios = <2 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "en_hsusb2_clk";
- };
-};
-
&gpmc {
- ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
- <5 0 0x2c000000 0x01000000>;
-
nand@0,0 {
compatible = "ti,omap2-nand";
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
@@ -309,9 +107,4 @@
reg = <0x780000 0x1f880000>;
};
};
-
- ethernet@gpmc {
- pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
- };
};
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
new file mode 100644
index 000000000000..c1fb6ecd5aff
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
@@ -0,0 +1,214 @@
+/*
+ * Common support for omap3 EVM 35xx/37xx processor modules
+ */
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl12xx_gpio>;
+ };
+};
+
+&dss {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+};
+
+&hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehci_phy_pins>;
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
+ OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
+ OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
+ OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
+ >;
+ };
+
+ /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ >;
+ };
+
+ /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
+ on_board_gpio_61: pinmux_ehci_port_select_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+
+ /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+
+ wl12xx_gpio: pinmux_wl12xx_gpio {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
+ >;
+ };
+
+ smsc911x_pins: pinmux_smsc911x_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+&uart2 {
+ interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+};
+
+&uart3 {
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+/*
+ * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
+ * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
+ */
+&gpio2 {
+ en_usb2_port {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
+ output-low;
+ line-name = "enable usb2 port";
+ };
+};
+
+/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
+&twl_gpio {
+ en_on_board_gpio_61 {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "en_hsusb2_clk";
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
+ <5 0 0x2c000000 0x01000000>; /* CS5: 16MB for LAN9220 */
+
+ ethernet@gpmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&smsc911x_pins>;
+ };
+};
--
2.14.1
The Sharp panel 'envdd' regulator is now selected properly. This commit
eliminates a dummy regulator assignment at boot.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
index 157345bb8e79..21e5683e7327 100644
--- a/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
+++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
@@ -29,6 +29,7 @@
compatible = "sharp,ls037v7dw01";
label = "lcd";
power-supply = <&lcd_3v3>;
+ envdd-supply = <&lcd_3v3>;
port {
lcd_in: endpoint {
--
2.14.1
This commit allows OMAP3530 variants to use common data that is
available in 'omap3-evm-processor-common.dtsi'. It adds proper pinmux
macros for 'omap3_pmx_core2' on OMAP3430. The Micron NAND chip is also
added for the TMDSEVM3530 processor module.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm.dts | 76 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 72 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 99b2bfcd1059..21a3b88aef0c 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -9,13 +9,81 @@
#include "omap34xx.dtsi"
#include "omap3-evm-common.dtsi"
+#include "omap3-evm-processor-common.dtsi"
/ {
model = "TI OMAP35XX EVM (TMDSEVM3530)";
- compatible = "ti,omap3-evm", "ti,omap3";
+ compatible = "ti,omap3-evm", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+
+ ehci_phy_pins: pinmux_ehci_phy_pins {
+ pinctrl-single,pins = <
+
+ /* EHCI PHY reset GPIO etk_d7.gpio_21 */
+ OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
+
+ /* EHCI VBUS etk_d8.gpio_22 */
+ OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+
+ /* etk_d10.hsusb2_clk */
+ OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d11.hsusb2_stp */
+ OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d12.hsusb2_dir */
+ OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d13.hsusb2_nxt */
+ OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d14.hsusb2_data0 */
+ OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d15.hsusb2_data1 */
+ OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+};
+
+&gpmc {
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ linux,mtd-name= "micron,mt29f2g16abdhc";
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ ti,nand-ecc-opt = "bch8";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
};
};
--
2.14.1
This commit eliminates two dummy regulator assignments.
Signed-off-by: Derald D. Woods <[email protected]>
---
arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
index c1fb6ecd5aff..ce7f42f9448c 100644
--- a/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
+++ b/arch/arm/boot/dts/omap3-evm-processor-common.dtsi
@@ -15,6 +15,8 @@
};
&dss {
+ vdds_dsi-supply = <&vpll2>;
+ vdda_video-supply = <&lcd_3v3>;
pinctrl-names = "default";
pinctrl-0 = <
&dss_dpi_pins1
--
2.14.1
On Tue, Sep 12, 2017 at 06:48:20PM -0500, Derald D. Woods wrote:
> This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
> processor module data that is shared with 'omap3-evm-37xx.dts'. A new
> common file for processor module data is introduced to help facilitate
> the updated OMAP3530 support.
>
Are there any further concerns after v3?
Derald
> Changes in v3
> -------------
> - Drop unnecessary compatible string change to Sharp LCD panel
>
> Changes in v2
> -------------
> - Pull in change from linux-next
> (ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc")
> - Add compatible and supply fix for LCD panel
> - Add supply references for DSS
> - Add "Signed-off-by" for each patch
>
> Derald D. Woods (4):
> ARM: dts: omap3-evm-37xx: Add common processor module support
> ARM: dts: omap3-evm: Add OMAP3530 specific device tree processor data
> ARM: dts: omap3: Add Sharp LS037V7DW01 'envdd' supply
> ARM: dts: omap3-evm: Add DSS {vdds_dsi,vdda_video}-supply references
>
> arch/arm/boot/dts/omap3-evm-37xx.dts | 209 +-------------------
> arch/arm/boot/dts/omap3-evm-processor-common.dtsi | 216 +++++++++++++++++++++
> arch/arm/boot/dts/omap3-evm.dts | 76 +++++++-
> .../boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi | 1 +
> 4 files changed, 290 insertions(+), 212 deletions(-)
> create mode 100644 arch/arm/boot/dts/omap3-evm-processor-common.dtsi
>
> --
> 2.14.1
>
* Derald D. Woods <[email protected]> [170928 19:05]:
> On Tue, Sep 12, 2017 at 06:48:20PM -0500, Derald D. Woods wrote:
> > This patch set allows TMDSEVM3530(omap3-evm.dts) to boot using common
> > processor module data that is shared with 'omap3-evm-37xx.dts'. A new
> > common file for processor module data is introduced to help facilitate
> > the updated OMAP3530 support.
> >
>
>
> Are there any further concerns after v3?
Looks godo to me thanks. And also still boots on the 37xx-evm,
so applying into omap-for-v4.15/dt.
Regards,
Tony