2017-12-22 09:42:55

by Yong

Subject: [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

Add binding documentation for Allwinner V3s CSI.

Signed-off-by: Yong Deng <[email protected]>
---
.../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
1 file changed, 51 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt

diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
new file mode 100644
index 0000000..b5bfe3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
@@ -0,0 +1,51 @@
+Allwinner V3s Camera Sensor Interface
+------------------------------
+
+Required properties:
+ - compatible: value must be "allwinner,sun8i-v3s-csi"
+ - reg: base address and size of the memory-mapped region.
+ - interrupts: interrupt associated to this IP
+ - clocks: phandles to the clocks feeding the CSI
+ * bus: the CSI interface clock
+ * mod: the CSI module clock
+ * ram: the CSI DRAM clock
+ - clock-names: the clock names mentioned above
+ - resets: phandles to the reset line driving the CSI
+
+- ports: A ports node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ Currently, the driver only support the parallel interface. So, a single port
+ node with one endpoint and parallel bus is supported.
+
+Example:
+
+ csi1: csi@1cb4000 {
+ compatible = "allwinner,sun8i-v3s-csi";
+ reg = <0x01cb4000 0x1000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CSI>,
+ <&ccu CLK_CSI1_SCLK>,
+ <&ccu CLK_DRAM_CSI>;
+ clock-names = "bus", "mod", "ram";
+ resets = <&ccu RST_BUS_CSI>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Parallel bus endpoint */
+ csi1_ep: endpoint {
+ remote-endpoint = <&adv7611_ep>;
+ bus-width = <16>;
+ data-shift = <0>;
+
+ /* If hsync-active/vsync-active are missing,
+ embedded BT.656 sync is used */
+ hsync-active = <0>; /* Active low */
+ vsync-active = <0>; /* Active low */
+ data-active = <1>; /* Active high */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+ };
+
--
1.8.3.1

2017-12-22 10:00:20

by Priit Laes

Subject: Re: [linux-sunxi] [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> Add binding documentation for Allwinner V3s CSI.
>
> Signed-off-by: Yong Deng <[email protected]>
> ---
> .../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
> 1 file changed, 51 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
>
> diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> new file mode 100644
> index 0000000..b5bfe3f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> @@ -0,0 +1,51 @@
> +Allwinner V3s Camera Sensor Interface
> +------------------------------

Not sure whether syntax for these files is proper reStructuredText/Markdown,
but the underline-ish style expects the title and underline having same length.

> +
> +Required properties:
> + - compatible: value must be "allwinner,sun8i-v3s-csi"
> + - reg: base address and size of the memory-mapped region.
> + - interrupts: interrupt associated to this IP
> + - clocks: phandles to the clocks feeding the CSI
> + * bus: the CSI interface clock
> + * mod: the CSI module clock
> + * ram: the CSI DRAM clock
> + - clock-names: the clock names mentioned above
> + - resets: phandles to the reset line driving the CSI
> +
> +- ports: A ports node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> + Currently, the driver only support the parallel interface. So, a single port
^^ supports
> + node with one endpoint and parallel bus is supported.
> +
> +Example:
> +
> + csi1: csi@1cb4000 {
> + compatible = "allwinner,sun8i-v3s-csi";
> + reg = <0x01cb4000 0x1000>;
> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_CSI>,
> + <&ccu CLK_CSI1_SCLK>,
> + <&ccu CLK_DRAM_CSI>;
> + clock-names = "bus", "mod", "ram";
> + resets = <&ccu RST_BUS_CSI>;
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Parallel bus endpoint */
> + csi1_ep: endpoint {
> + remote-endpoint = <&adv7611_ep>;
> + bus-width = <16>;
> + data-shift = <0>;
> +
> + /* If hsync-active/vsync-active are missing,
> + embedded BT.656 sync is used */
> + hsync-active = <0>; /* Active low */
> + vsync-active = <0>; /* Active low */
> + data-active = <1>; /* Active high */
> + pclk-sample = <1>; /* Rising */
> + };
> + };
> + };
> +
> --
> 1.8.3.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> For more options, visit https://groups.google.com/d/optout.

2017-12-22 10:59:57

by Yong

Subject: Re: [linux-sunxi] [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

On Fri, 22 Dec 2017 10:00:08 +0000
Priit Laes <[email protected]> wrote:

> On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> > Add binding documentation for Allwinner V3s CSI.
> >
> > Signed-off-by: Yong Deng <[email protected]>
> > ---
> > .../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
> > 1 file changed, 51 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > new file mode 100644
> > index 0000000..b5bfe3f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > @@ -0,0 +1,51 @@
> > +Allwinner V3s Camera Sensor Interface
> > +------------------------------
>
> Not sure whether syntax for these files is proper reStructuredText/Markdown,
> but the underline-ish style expects the title and underline having same length.

OK.

>
> > +
> > +Required properties:
> > + - compatible: value must be "allwinner,sun8i-v3s-csi"
> > + - reg: base address and size of the memory-mapped region.
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the CSI
> > + * bus: the CSI interface clock
> > + * mod: the CSI module clock
> > + * ram: the CSI DRAM clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandles to the reset line driving the CSI
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > + Currently, the driver only support the parallel interface. So, a single port
> ^^ supports
> > + node with one endpoint and parallel bus is supported.
> > +
> > +Example:
> > +
> > + csi1: csi@1cb4000 {
> > + compatible = "allwinner,sun8i-v3s-csi";
> > + reg = <0x01cb4000 0x1000>;
> > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_CSI>,
> > + <&ccu CLK_CSI1_SCLK>,
> > + <&ccu CLK_DRAM_CSI>;
> > + clock-names = "bus", "mod", "ram";
> > + resets = <&ccu RST_BUS_CSI>;
> > +
> > + port {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Parallel bus endpoint */
> > + csi1_ep: endpoint {
> > + remote-endpoint = <&adv7611_ep>;
> > + bus-width = <16>;
> > + data-shift = <0>;
> > +
> > + /* If hsync-active/vsync-active are missing,
> > + embedded BT.656 sync is used */
> > + hsync-active = <0>; /* Active low */
> > + vsync-active = <0>; /* Active low */
> > + data-active = <1>; /* Active high */
> > + pclk-sample = <1>; /* Rising */
> > + };
> > + };
> > + };
> > +
> > --
> > 1.8.3.1
> >
> > --
> > You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> > To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> > For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> For more options, visit https://groups.google.com/d/optout.


Thanks,
Yong

2017-12-26 21:53:59

by Rob Herring

Subject: Re: [linux-sunxi] [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

On Fri, Dec 22, 2017 at 10:00:08AM +0000, Priit Laes wrote:
> On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> > Add binding documentation for Allwinner V3s CSI.
> >
> > Signed-off-by: Yong Deng <[email protected]>
> > ---
> > .../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
> > 1 file changed, 51 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > new file mode 100644
> > index 0000000..b5bfe3f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > @@ -0,0 +1,51 @@
> > +Allwinner V3s Camera Sensor Interface
> > +------------------------------
>
> Not sure whether syntax for these files is proper reStructuredText/Markdown,
> but the underline-ish style expects the title and underline having same length.

The binding files are not rst/md format, but still the comment is just
good style.

Rob

2017-12-26 21:55:46

by Rob Herring

Subject: Re: [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> Add binding documentation for Allwinner V3s CSI.
>
> Signed-off-by: Yong Deng <[email protected]>
> ---
> .../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
> 1 file changed, 51 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
>
> diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> new file mode 100644
> index 0000000..b5bfe3f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> @@ -0,0 +1,51 @@
> +Allwinner V3s Camera Sensor Interface
> +------------------------------
> +
> +Required properties:
> + - compatible: value must be "allwinner,sun8i-v3s-csi"
> + - reg: base address and size of the memory-mapped region.
> + - interrupts: interrupt associated to this IP
> + - clocks: phandles to the clocks feeding the CSI
> + * bus: the CSI interface clock
> + * mod: the CSI module clock
> + * ram: the CSI DRAM clock
> + - clock-names: the clock names mentioned above
> + - resets: phandles to the reset line driving the CSI
> +
> +- ports: A ports node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> + Currently, the driver only support the parallel interface. So, a single port
> + node with one endpoint and parallel bus is supported.

What the driver supports is not relevant. Please document what the h/w
has.

> +
> +Example:
> +
> + csi1: csi@1cb4000 {
> + compatible = "allwinner,sun8i-v3s-csi";
> + reg = <0x01cb4000 0x1000>;
> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_CSI>,
> + <&ccu CLK_CSI1_SCLK>,
> + <&ccu CLK_DRAM_CSI>;
> + clock-names = "bus", "mod", "ram";
> + resets = <&ccu RST_BUS_CSI>;
> +
> + port {

> + #address-cells = <1>;
> + #size-cells = <0>;

These are not needed with a single endpoint.

> +
> + /* Parallel bus endpoint */
> + csi1_ep: endpoint {
> + remote-endpoint = <&adv7611_ep>;
> + bus-width = <16>;
> + data-shift = <0>;
> +
> + /* If hsync-active/vsync-active are missing,
> + embedded BT.656 sync is used */
> + hsync-active = <0>; /* Active low */
> + vsync-active = <0>; /* Active low */
> + data-active = <1>; /* Active high */
> + pclk-sample = <1>; /* Rising */
> + };
> + };
> + };
> +
> --
> 1.8.3.1
>

2017-12-28 01:05:50

by Yong

Subject: Re: [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

Hi,

On Tue, 26 Dec 2017 15:55:37 -0600
Rob Herring <[email protected]> wrote:

> On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:
> > Add binding documentation for Allwinner V3s CSI.
> >
> > Signed-off-by: Yong Deng <[email protected]>
> > ---
> > .../devicetree/bindings/media/sun6i-csi.txt | 51 ++++++++++++++++++++++
> > 1 file changed, 51 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > new file mode 100644
> > index 0000000..b5bfe3f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > @@ -0,0 +1,51 @@
> > +Allwinner V3s Camera Sensor Interface
> > +------------------------------
> > +
> > +Required properties:
> > + - compatible: value must be "allwinner,sun8i-v3s-csi"
> > + - reg: base address and size of the memory-mapped region.
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the CSI
> > + * bus: the CSI interface clock
> > + * mod: the CSI module clock
> > + * ram: the CSI DRAM clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandles to the reset line driving the CSI
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > + Currently, the driver only support the parallel interface. So, a single port
> > + node with one endpoint and parallel bus is supported.
>
> What the driver supports is not relevant. Please document what the h/w
> has.

OK.

>
> > +
> > +Example:
> > +
> > + csi1: csi@1cb4000 {
> > + compatible = "allwinner,sun8i-v3s-csi";
> > + reg = <0x01cb4000 0x1000>;
> > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_CSI>,
> > + <&ccu CLK_CSI1_SCLK>,
> > + <&ccu CLK_DRAM_CSI>;
> > + clock-names = "bus", "mod", "ram";
> > + resets = <&ccu RST_BUS_CSI>;
> > +
> > + port {
>
> > + #address-cells = <1>;
> > + #size-cells = <0>;
>
> These are not needed with a single endpoint.

OK.

>
> > +
> > + /* Parallel bus endpoint */
> > + csi1_ep: endpoint {
> > + remote-endpoint = <&adv7611_ep>;
> > + bus-width = <16>;
> > + data-shift = <0>;
> > +
> > + /* If hsync-active/vsync-active are missing,
> > + embedded BT.656 sync is used */
> > + hsync-active = <0>; /* Active low */
> > + vsync-active = <0>; /* Active low */
> > + data-active = <1>; /* Active high */
> > + pclk-sample = <1>; /* Rising */
> > + };
> > + };
> > + };
> > +
> > --
> > 1.8.3.1
> >


Thanks,
Yong