Hi all,
This series adds 1000BaseX and 2500BaseX support to the Marvell PPv2
driver. In order to use it, the 2.5 SGMII mode is added in the Marvell
common PHY driver (cp110-comphy).
This was tested on a mcbin.
All patches should probably go through net-next as patch 4/4 depends on
patch 1/4 to build and work.
Please note the two mvpp2 patches do not conflict with the ACPI series
v2 Marcin sent a few days ago, and the two series can be processed in
parallel. (Marcin is aware of me sending this series).
Thanks!
Antoine
Since v3:
- Stopped setting the MII_SPEED bit in the GMAC AN register, as the
GMII_SPEED bit takes over anyway.
- Added Andrew's Reviewed-by on patch 4/4.
Since v2:
- Added a comment before mvpp22_comphy_init() about the different PHY modes
used and why they differ between the PPv2 driver and the COMPHY one.
Since v1:
- s/PHY_MODE_SGMII_2_5G/PHY_MODE_2500SGMII/
- Fixed a build error in 'net: mvpp2: 1000baseX support' (which was solved in
the 2500baseX support one, but the bisection was broken).
- Removed the dt patches, as the fourth network interface on the mcbin also
needs PHYLINK support in the PPv2 driver to be correctly supported.
Antoine Tenart (4):
phy: add 2.5G SGMII mode to the phy_mode enum
phy: cp110-comphy: 2.5G SGMII mode
net: mvpp2: 1000baseX support
net: mvpp2: 2500baseX support
drivers/net/ethernet/marvell/mvpp2.c | 74 ++++++++++++++++++++++++----
drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 17 +++++--
include/linux/phy/phy.h | 1 +
3 files changed, 79 insertions(+), 13 deletions(-)
--
2.14.3
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2.c | 45 ++++++++++++++++++++++++++++--------
1 file changed, 35 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index a19760736b71..257a6b99b4ca 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4501,6 +4501,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
mvpp22_gop_init_rgmii(port);
break;
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4538,7 +4539,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4568,7 +4570,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
}
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4580,7 +4583,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4605,6 +4609,7 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
switch (port->phy_interface) {
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4625,7 +4630,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
{
u32 val;
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
val |= MVPP22_CTRL4_SYNC_BYPASS_DIS | MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
@@ -4640,9 +4646,11 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
}
- /* The port is connected to a copper PHY */
val = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
- val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ val |= MVPP2_GMAC_PORT_TYPE_MASK;
+ else
+ val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
writel(val, port->base + MVPP2_GMAC_CTRL_0_REG);
val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
@@ -4651,6 +4659,19 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
MVPP2_GMAC_AN_DUPLEX_EN;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
val |= MVPP2_GMAC_IN_BAND_AUTONEG;
+
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ /* 1000BaseX port cannot negotiate speed nor can it
+ * negotiate duplex: they are always operating with a
+ * fixed speed of 1000Mbps in full duplex, so force
+ * 1000 speed and full duplex here.
+ */
+ val |= MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+ else
+ val |= MVPP2_GMAC_AN_SPEED_EN |
+ MVPP2_GMAC_AN_DUPLEX_EN;
+
writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
}
@@ -4671,7 +4692,8 @@ static void mvpp2_port_mii_gmac_configure(struct mvpp2_port *port)
/* Configure the PCS and in-band AN */
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
} else if (phy_interface_mode_is_rgmii(port->phy_interface)) {
val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -4733,7 +4755,8 @@ static void mvpp2_port_mii_set(struct mvpp2_port *port)
mvpp22_port_mii_set(port);
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
mvpp2_port_mii_gmac_configure(port);
else if (port->phy_interface == PHY_INTERFACE_MODE_10GKR)
mvpp2_port_mii_xlg_configure(port);
@@ -4810,7 +4833,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port)
else
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6023,7 +6047,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
link = true;
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
--
2.14.3
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2.c | 49 ++++++++++++++++++++++++++++--------
1 file changed, 39 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 257a6b99b4ca..541b393a8583 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4502,6 +4502,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
break;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4540,7 +4541,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4571,7 +4573,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4584,7 +4587,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4599,6 +4603,16 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
mvpp22_gop_unmask_irq(port);
}
+/* Sets the PHY mode of the COMPHY (which configures the serdes lanes).
+ *
+ * The PHY mode used by the PPv2 driver comes from the network subsystem, while
+ * the one given to the COMPHY comes from the generic PHY subsystem. Hence they
+ * differ.
+ *
+ * The COMPHY configures the serdes lanes regardless of the actual use of the
+ * lanes by the physical layer. This is why configurations like
+ * "PPv2 (2500BaseX) - COMPHY (2500SGMII)" are valid.
+ */
static int mvpp22_comphy_init(struct mvpp2_port *port)
{
enum phy_mode mode;
@@ -4612,6 +4626,9 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ mode = PHY_MODE_2500SGMII;
+ break;
case PHY_INTERFACE_MODE_10GKR:
mode = PHY_MODE_10GKR;
break;
@@ -4631,7 +4648,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
u32 val;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
val |= MVPP22_CTRL4_SYNC_BYPASS_DIS | MVPP22_CTRL4_DP_CLK_SEL |
MVPP22_CTRL4_QSGMII_BYPASS_ACTIVE;
@@ -4647,7 +4665,8 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
}
val = readl(port->base + MVPP2_GMAC_CTRL_0_REG);
- if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PORT_TYPE_MASK;
else
val &= ~MVPP2_GMAC_PORT_TYPE_MASK;
@@ -4660,7 +4679,13 @@ static void mvpp2_port_mii_gmac_configure_mode(struct mvpp2_port *port)
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
val |= MVPP2_GMAC_IN_BAND_AUTONEG;
- if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ /* Clear all fields we may want to explicitly set below */
+ val &= ~(MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_AN_SPEED_EN |
+ MVPP2_GMAC_AN_DUPLEX_EN);
+
+ if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX |
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
/* 1000BaseX port cannot negotiate speed nor can it
* negotiate duplex: they are always operating with a
* fixed speed of 1000Mbps in full duplex, so force
@@ -4693,7 +4718,8 @@ static void mvpp2_port_mii_gmac_configure(struct mvpp2_port *port)
/* Configure the PCS and in-band AN */
val = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
} else if (phy_interface_mode_is_rgmii(port->phy_interface)) {
val &= ~MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -4756,7 +4782,8 @@ static void mvpp2_port_mii_set(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
mvpp2_port_mii_gmac_configure(port);
else if (port->phy_interface == PHY_INTERFACE_MODE_10GKR)
mvpp2_port_mii_xlg_configure(port);
@@ -4834,7 +4861,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port)
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6048,7 +6076,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
--
2.14.3
This patch allow the CP100 comphy to configure some lanes in the
2.5G SGMII mode. This mode is quite close to SGMII and uses nearly the
same code path.
Signed-off-by: Antoine Tenart <[email protected]>
---
drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 17 ++++++++++++++---
1 file changed, 14 insertions(+), 3 deletions(-)
diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
index a0d522154cdf..4ef429250d7b 100644
--- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
+++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
@@ -135,19 +135,25 @@ struct mvebu_comhy_conf {
static const struct mvebu_comhy_conf mvebu_comphy_cp110_modes[] = {
/* lane 0 */
MVEBU_COMPHY_CONF(0, 1, PHY_MODE_SGMII, 0x1),
+ MVEBU_COMPHY_CONF(0, 1, PHY_MODE_2500SGMII, 0x1),
/* lane 1 */
MVEBU_COMPHY_CONF(1, 2, PHY_MODE_SGMII, 0x1),
+ MVEBU_COMPHY_CONF(1, 2, PHY_MODE_2500SGMII, 0x1),
/* lane 2 */
MVEBU_COMPHY_CONF(2, 0, PHY_MODE_SGMII, 0x1),
+ MVEBU_COMPHY_CONF(2, 0, PHY_MODE_2500SGMII, 0x1),
MVEBU_COMPHY_CONF(2, 0, PHY_MODE_10GKR, 0x1),
/* lane 3 */
MVEBU_COMPHY_CONF(3, 1, PHY_MODE_SGMII, 0x2),
+ MVEBU_COMPHY_CONF(3, 1, PHY_MODE_2500SGMII, 0x2),
/* lane 4 */
MVEBU_COMPHY_CONF(4, 0, PHY_MODE_SGMII, 0x2),
+ MVEBU_COMPHY_CONF(4, 0, PHY_MODE_2500SGMII, 0x2),
MVEBU_COMPHY_CONF(4, 0, PHY_MODE_10GKR, 0x2),
MVEBU_COMPHY_CONF(4, 1, PHY_MODE_SGMII, 0x1),
/* lane 5 */
MVEBU_COMPHY_CONF(5, 2, PHY_MODE_SGMII, 0x1),
+ MVEBU_COMPHY_CONF(5, 2, PHY_MODE_2500SGMII, 0x1),
};
struct mvebu_comphy_priv {
@@ -206,6 +212,10 @@ static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
if (mode == PHY_MODE_10GKR)
val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xe) |
MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xe);
+ else if (mode == PHY_MODE_2500SGMII)
+ val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0x8) |
+ MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0x8) |
+ MVEBU_COMPHY_SERDES_CFG0_HALF_BUS;
else if (mode == PHY_MODE_SGMII)
val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0x6) |
MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0x6) |
@@ -296,13 +306,13 @@ static int mvebu_comphy_init_plls(struct mvebu_comphy_lane *lane,
return 0;
}
-static int mvebu_comphy_set_mode_sgmii(struct phy *phy)
+static int mvebu_comphy_set_mode_sgmii(struct phy *phy, enum phy_mode mode)
{
struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
struct mvebu_comphy_priv *priv = lane->priv;
u32 val;
- mvebu_comphy_ethernet_init_reset(lane, PHY_MODE_SGMII);
+ mvebu_comphy_ethernet_init_reset(lane, mode);
val = readl(priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
val &= ~MVEBU_COMPHY_RX_CTRL1_CLK8T_EN;
@@ -487,7 +497,8 @@ static int mvebu_comphy_power_on(struct phy *phy)
switch (lane->mode) {
case PHY_MODE_SGMII:
- ret = mvebu_comphy_set_mode_sgmii(phy);
+ case PHY_MODE_2500SGMII:
+ ret = mvebu_comphy_set_mode_sgmii(phy, lane->mode);
break;
case PHY_MODE_10GKR:
ret = mvebu_comphy_set_mode_10gkr(phy);
--
2.14.3
This patch adds one more generic PHY mode to the phy_mode enum, to allow
configuring generic PHYs to the 2.5G SGMII mode by using the set_mode
callback.
Signed-off-by: Antoine Tenart <[email protected]>
---
include/linux/phy/phy.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
index 4f8423a948d5..5a80e9de3686 100644
--- a/include/linux/phy/phy.h
+++ b/include/linux/phy/phy.h
@@ -28,6 +28,7 @@ enum phy_mode {
PHY_MODE_USB_DEVICE,
PHY_MODE_USB_OTG,
PHY_MODE_SGMII,
+ PHY_MODE_2500SGMII,
PHY_MODE_10GKR,
PHY_MODE_UFS_HS_A,
PHY_MODE_UFS_HS_B,
--
2.14.3
From: Antoine Tenart <[email protected]>
Date: Wed, 10 Jan 2018 16:58:04 +0100
> This series adds 1000BaseX and 2500BaseX support to the Marvell PPv2
> driver. In order to use it, the 2.5 SGMII mode is added in the Marvell
> common PHY driver (cp110-comphy).
Series applied, thank you.
From: David Miller <[email protected]>
Date: Thu, 11 Jan 2018 11:23:37 -0500 (EST)
> From: Antoine Tenart <[email protected]>
> Date: Wed, 10 Jan 2018 16:58:04 +0100
>
>> This series adds 1000BaseX and 2500BaseX support to the Marvell PPv2
>> driver. In order to use it, the 2.5 SGMII mode is added in the Marvell
>> common PHY driver (cp110-comphy).
>
> Series applied, thank you.
Actually, this introduced build warnings, I'm reverting. Please fix this
and repost.
Thank you.
drivers/net/ethernet/marvell/mvpp2.c: In function ?mvpp2_port_mii_gmac_configure_mode?:
drivers/net/ethernet/marvell/mvpp2.c:4687:26: warning: suggest parentheses around comparison in operand of ?|? [-Wparentheses]
if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX |
~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hello,
On Thu, 11 Jan 2018 11:32:03 -0500 (EST), David Miller wrote:
> From: David Miller <[email protected]>
> Date: Thu, 11 Jan 2018 11:23:37 -0500 (EST)
>
> > From: Antoine Tenart <[email protected]>
> > Date: Wed, 10 Jan 2018 16:58:04 +0100
> >
> >> This series adds 1000BaseX and 2500BaseX support to the Marvell PPv2
> >> driver. In order to use it, the 2.5 SGMII mode is added in the Marvell
> >> common PHY driver (cp110-comphy).
> >
> > Series applied, thank you.
>
> Actually, this introduced build warnings, I'm reverting. Please fix this
> and repost.
>
> Thank you.
>
> drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_port_mii_gmac_configure_mode’:
> drivers/net/ethernet/marvell/mvpp2.c:4687:26: warning: suggest parentheses around comparison in operand of ‘|’ [-Wparentheses]
> if (port->phy_interface == PHY_INTERFACE_MODE_1000BASEX |
> ~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is actually a very good warning: it should be a || and not |.
Best regards,
Thomas
--
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
Hi David,
On Thu, Jan 11, 2018 at 11:32:03AM -0500, David Miller wrote:
>
> Actually, this introduced build warnings, I'm reverting. Please fix this
> and repost.
The warning points a real issue. I'm sorry about that, seems like I
forgot to test this one after the last change... I'll send a new
(tested) version.
Thanks!
Antoine
--
Antoine T?nart, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com