From: "H. Nikolaus Schaller" <[email protected]>
[ Upstream commit 934df23171e7c5b71d937104d4957891c39748ff ]
1. check if chip is really present and don't succeed if it isn't.
2. if it succeeds, power down the chip until accessed
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/input/touchscreen/tsc2007.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/input/touchscreen/tsc2007.c b/drivers/input/touchscreen/tsc2007.c
index 1bf9906b5a3f..75810fa97db5 100644
--- a/drivers/input/touchscreen/tsc2007.c
+++ b/drivers/input/touchscreen/tsc2007.c
@@ -456,6 +456,14 @@ static int tsc2007_probe(struct i2c_client *client,
tsc2007_stop(ts);
+ /* power down the chip (TSC2007_SETUP does not ACK on I2C) */
+ err = tsc2007_xfer(ts, PWRDOWN);
+ if (err < 0) {
+ dev_err(&client->dev,
+ "Failed to setup chip: %d\n", err);
+ return err; /* usually, chip does not respond */
+ }
+
err = input_register_device(input_dev);
if (err) {
dev_err(&client->dev,
--
2.14.1
From: Shaohua Li <[email protected]>
[ Upstream commit 06cceedcca67a93ac7f7aa93bbd9980c7496d14e ]
cgroup could be throttled to a limit but when all cgroups cross high
limit, queue enters a higher state and so the group should be throttled
to a higher limit. It's possible the cgroup is sleeping because of
throttle and other cgroups don't dispatch IO any more. In this case,
nobody can trigger current downgrade/upgrade logic. To fix this issue,
we could either set up a timer to wakeup the cgroup if other cgroups are
idle or make sure this cgroup doesn't sleep too long. Setting up a timer
means we must change the timer very frequently. This patch chooses the
latter. Making cgroup sleep time not too big wouldn't change cgroup
bps/iops, but could make it wakeup more frequently, which isn't a big
issue because throtl_slice * 8 is already quite big.
Signed-off-by: Shaohua Li <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
block/blk-throttle.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/block/blk-throttle.c b/block/blk-throttle.c
index 5b9c6d5c3636..fd51c8be247d 100644
--- a/block/blk-throttle.c
+++ b/block/blk-throttle.c
@@ -648,6 +648,17 @@ static void throtl_dequeue_tg(struct throtl_grp *tg)
static void throtl_schedule_pending_timer(struct throtl_service_queue *sq,
unsigned long expires)
{
+ unsigned long max_expire = jiffies + 8 * throtl_slice;
+
+ /*
+ * Since we are adjusting the throttle limit dynamically, the sleep
+ * time calculated according to previous limit might be invalid. It's
+ * possible the cgroup sleep time is very long and no other cgroups
+ * have IO running so notify the limit changes. Make sure the cgroup
+ * doesn't sleep too long to avoid the missed notification.
+ */
+ if (time_after(expires, max_expire))
+ expires = max_expire;
mod_timer(&sq->pending_timer, expires);
throtl_log(sq, "schedule timer. delay=%lu jiffies=%lu",
expires - jiffies, jiffies);
--
2.14.1
From: Phil Turnbull <[email protected]>
[ Upstream commit 540fca35e38d15777b310f450f63f056e63039f5 ]
FM10K_REMOVED expects a hardware address, not a 'struct fm10k_hw'.
Fixes: 5cb8db4a4cbc ("fm10k: Add support for VF")
Signed-off-by: Phil Turnbull <[email protected]>
Tested-by: Krishneil Singh <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c b/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
index 2d04464e6aa3..125fdf40daa6 100644
--- a/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
+++ b/drivers/net/ethernet/intel/fm10k/fm10k_ethtool.c
@@ -840,7 +840,7 @@ static void fm10k_self_test(struct net_device *dev,
memset(data, 0, sizeof(*data) * FM10K_TEST_LEN);
- if (FM10K_REMOVED(hw)) {
+ if (FM10K_REMOVED(hw->hw_addr)) {
netif_err(interface, drv, dev,
"Interface removed - test blocked\n");
eth_test->flags |= ETH_TEST_FL_FAILED;
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit 16fe68dcab5702a024d85229ff7e98979cb701a5 ]
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: ee9141522dcf13f8 ("ARM: shmobile: r8a7791: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7791.dtsi | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 516d62ac25a9..297a19de3c66 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -1001,8 +1001,11 @@
compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150998 0 4>, <0 0xe61509a8 0 4>;
clocks = <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI_ALL>,
<&p_clk>,
<&mstp10_clks R8A7791_CLK_SCU_ALL>, <&mstp10_clks R8A7791_CLK_SCU_ALL>,
<&mstp10_clks R8A7791_CLK_SCU_ALL>, <&mstp10_clks R8A7791_CLK_SCU_ALL>,
--
2.14.1
From: David Daney <[email protected]>
[ Upstream commit 1ef0910cfd681f0bd0b81f8809935b2006e9cfb9 ]
If bpf_needs_clear_a() returns true, only actually clear it if it is
ever used. If it is not used, we don't save and restore it, so the
clearing has the nasty side effect of clobbering caller state.
Also, don't emit stack pointer adjustment instructions if the
adjustment amount is zero.
Signed-off-by: David Daney <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Steven J. Hill <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/15745/
Signed-off-by: Ralf Baechle <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/mips/net/bpf_jit.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/arch/mips/net/bpf_jit.c b/arch/mips/net/bpf_jit.c
index 9fd82f48f8ed..32d2673439ad 100644
--- a/arch/mips/net/bpf_jit.c
+++ b/arch/mips/net/bpf_jit.c
@@ -562,7 +562,8 @@ static void save_bpf_jit_regs(struct jit_ctx *ctx, unsigned offset)
u32 sflags, tmp_flags;
/* Adjust the stack pointer */
- emit_stack_offset(-align_sp(offset), ctx);
+ if (offset)
+ emit_stack_offset(-align_sp(offset), ctx);
if (ctx->flags & SEEN_CALL) {
/* Argument save area */
@@ -641,7 +642,8 @@ static void restore_bpf_jit_regs(struct jit_ctx *ctx,
emit_load_stack_reg(r_ra, r_sp, real_off, ctx);
/* Restore the sp and discard the scrach memory */
- emit_stack_offset(align_sp(offset), ctx);
+ if (offset)
+ emit_stack_offset(align_sp(offset), ctx);
}
static unsigned int get_stack_depth(struct jit_ctx *ctx)
@@ -689,8 +691,14 @@ static void build_prologue(struct jit_ctx *ctx)
if (ctx->flags & SEEN_X)
emit_jit_reg_move(r_X, r_zero, ctx);
- /* Do not leak kernel data to userspace */
- if (bpf_needs_clear_a(&ctx->skf->insns[0]))
+ /*
+ * Do not leak kernel data to userspace, we only need to clear
+ * r_A if it is ever used. In fact if it is never used, we
+ * will not save/restore it, so clearing it in this case would
+ * corrupt the state of the caller.
+ */
+ if (bpf_needs_clear_a(&ctx->skf->insns[0]) &&
+ (ctx->flags & SEEN_A))
emit_jit_reg_move(r_A, r_zero, ctx);
}
--
2.14.1
From: Luca Coelho <[email protected]>
[ Upstream commit c7976f5272486e4ff406014c4b43e2fa3b70b052 ]
In the ieee80211_setup_sdata() we check if the interface type is valid
and, if not, call BUG(). This should never happen, but if there is
something wrong with the code, it will not be caught until the bug
happens when an interface is being set up. Calling BUG() is too
extreme for this and a WARN_ON() would be better used instead. Change
that.
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/mac80211/iface.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index eeae0abd01de..672e28918a44 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -1379,7 +1379,7 @@ static void ieee80211_setup_sdata(struct ieee80211_sub_if_data *sdata,
break;
case NL80211_IFTYPE_UNSPECIFIED:
case NUM_NL80211_IFTYPES:
- BUG();
+ WARN_ON(1);
break;
}
--
2.14.1
From: Julien BOIBESSOT <[email protected]>
[ Upstream commit 77be4c878c72e411ad22af96b6f81dd45c26450a ]
Indeed musl doesn't define old SIGCLD signal name but only new one SIGCHLD.
SIGCHLD is the new POSIX name for that signal so it doesn't change
anything on other libcs.
This fixes this kind of build error:
usbipd.c: In function ‘set_signal’:
usbipd.c:459:12: error: 'SIGCLD' undeclared (first use in this function)
sigaction(SIGCLD, &act, NULL);
^~~~~~
usbipd.c:459:12: note: each undeclared identifier is reported only once
for each function it appears in
Makefile:407: recipe for target 'usbipd.o' failed
make[3]: *** [usbipd.o] Error 1
Signed-off-by: Julien BOIBESSOT <[email protected]>
Acked-by: Shuah Khan <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/usb/usbip/src/usbipd.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/usb/usbip/src/usbipd.c b/tools/usb/usbip/src/usbipd.c
index 2f87f2d348ba..562599cdc89d 100644
--- a/tools/usb/usbip/src/usbipd.c
+++ b/tools/usb/usbip/src/usbipd.c
@@ -453,7 +453,7 @@ static void set_signal(void)
sigaction(SIGTERM, &act, NULL);
sigaction(SIGINT, &act, NULL);
act.sa_handler = SIG_IGN;
- sigaction(SIGCLD, &act, NULL);
+ sigaction(SIGCHLD, &act, NULL);
}
static const char *pid_file;
--
2.14.1
From: Tobias Jordan <[email protected]>
[ Upstream commit 2d9bbd02c54094ceffa555143b0d68cd06504d63 ]
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e8af (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Tobias Jordan <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-sun6i.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c
index 04e90851504c..6c042384a8c1 100644
--- a/drivers/spi/spi-sun6i.c
+++ b/drivers/spi/spi-sun6i.c
@@ -457,7 +457,7 @@ err_free_master:
static int sun6i_spi_remove(struct platform_device *pdev)
{
- pm_runtime_disable(&pdev->dev);
+ pm_runtime_force_suspend(&pdev->dev);
return 0;
}
--
2.14.1
From: Mimi Zohar <[email protected]>
[ Upstream commit b7e27bc1d42e8e0cc58b602b529c25cd0071b336 ]
Custom policies can require file signatures based on LSM labels. These
files are normally created and only afterwards labeled, requiring them
to be signed.
Instead of requiring file signatures based on LSM labels, entire
filesystems could require file signatures. In this case, we need the
ability of writing new files without requiring file signatures.
The definition of a "new" file was originally defined as any file with
a length of zero. Subsequent patches redefined a "new" file to be based
on the FILE_CREATE open flag. By combining the open flag with a file
size of zero, this patch relaxes the file signature requirement.
Fixes: 1ac202e978e1 ima: accept previously set IMA_NEW_FILE
Signed-off-by: Mimi Zohar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/integrity/ima/ima_appraise.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/security/integrity/ima/ima_appraise.c b/security/integrity/ima/ima_appraise.c
index ee7618115756..0bdf01decb63 100644
--- a/security/integrity/ima/ima_appraise.c
+++ b/security/integrity/ima/ima_appraise.c
@@ -206,7 +206,8 @@ int ima_appraise_measurement(int func, struct integrity_iint_cache *iint,
if (opened & FILE_CREATED)
iint->flags |= IMA_NEW_FILE;
if ((iint->flags & IMA_NEW_FILE) &&
- !(iint->flags & IMA_DIGSIG_REQUIRED))
+ (!(iint->flags & IMA_DIGSIG_REQUIRED) ||
+ (inode->i_size == 0)))
status = INTEGRITY_PASS;
goto out;
}
--
2.14.1
From: Xose Vazquez Perez <[email protected]>
[ Upstream commit b369a0471503130cfc74f9f62071db97f48948c3 ]
Commit 56f3d383f37b ("scsi: scsi_devinfo: Add TRY_VPD_PAGES to HITACHI
OPEN-V blacklist entry") modified some Hitachi entries:
HITACHI is always supporting VPD pages, even though it's claiming to
support SCSI Revision 3 only.
The same should have been done also for HP-rebranded.
[mkp: checkpatch and tweaked commit message]
Cc: Hannes Reinecke <[email protected]>
Cc: Takahiro Yasui <[email protected]>
Cc: Matthias Rudolph <[email protected]>
Cc: Martin K. Petersen <[email protected]>
Cc: James E.J. Bottomley <[email protected]>
Cc: SCSI ML <[email protected]>
Signed-off-by: Xose Vazquez Perez <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/scsi_devinfo.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/scsi/scsi_devinfo.c b/drivers/scsi/scsi_devinfo.c
index 2ae6f98e382b..90abf7f5289d 100644
--- a/drivers/scsi/scsi_devinfo.c
+++ b/drivers/scsi/scsi_devinfo.c
@@ -180,7 +180,7 @@ static struct {
{"HITACHI", "6586-", "*", BLIST_SPARSELUN | BLIST_LARGELUN},
{"HITACHI", "6588-", "*", BLIST_SPARSELUN | BLIST_LARGELUN},
{"HP", "A6189A", NULL, BLIST_SPARSELUN | BLIST_LARGELUN}, /* HP VA7400 */
- {"HP", "OPEN-", "*", BLIST_REPORTLUN2}, /* HP XP Arrays */
+ {"HP", "OPEN-", "*", BLIST_REPORTLUN2 | BLIST_TRY_VPD_PAGES}, /* HP XP Arrays */
{"HP", "NetRAID-4M", NULL, BLIST_FORCELUN},
{"HP", "HSV100", NULL, BLIST_REPORTLUN2 | BLIST_NOSTARTONADD},
{"HP", "C1557A", NULL, BLIST_FORCELUN},
--
2.14.1
From: Dan Carpenter <[email protected]>
[ Upstream commit d5ac225c7d64c9c3ef821239edc035634e594ec9 ]
The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array. The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.
Fixes: ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/usb/cpia2/cpia2_v4l.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/media/usb/cpia2/cpia2_v4l.c b/drivers/media/usb/cpia2/cpia2_v4l.c
index 9caea8344547..d793c630f1dd 100644
--- a/drivers/media/usb/cpia2/cpia2_v4l.c
+++ b/drivers/media/usb/cpia2/cpia2_v4l.c
@@ -812,7 +812,7 @@ static int cpia2_querybuf(struct file *file, void *fh, struct v4l2_buffer *buf)
struct camera_data *cam = video_drvdata(file);
if(buf->type != V4L2_BUF_TYPE_VIDEO_CAPTURE ||
- buf->index > cam->num_frames)
+ buf->index >= cam->num_frames)
return -EINVAL;
buf->m.offset = cam->buffers[buf->index].data - cam->frame_buffer;
@@ -863,7 +863,7 @@ static int cpia2_qbuf(struct file *file, void *fh, struct v4l2_buffer *buf)
if(buf->type != V4L2_BUF_TYPE_VIDEO_CAPTURE ||
buf->memory != V4L2_MEMORY_MMAP ||
- buf->index > cam->num_frames)
+ buf->index >= cam->num_frames)
return -EINVAL;
DBG("QBUF #%d\n", buf->index);
--
2.14.1
From: SeongJae Park <[email protected]>
[ Upstream commit 2adfa4210f8f35cdfb4e08318cc06b99752964c2 ]
The 'configinit.sh' script checks the format of optional argument for the
build directory, printing an error message if the format is not valid.
However, the error message uses the wrong variable, indicating an empty
string even though the user entered a non-empty (but erroneous) string.
This commit fixes the script to use the correct variable.
Fixes: c87b9c601ac8 ("rcutorture: Add KVM-based test framework")
Signed-off-by: SeongJae Park <[email protected]>
Signed-off-by: Paul E. McKenney <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/testing/selftests/rcutorture/bin/configinit.sh | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/testing/selftests/rcutorture/bin/configinit.sh b/tools/testing/selftests/rcutorture/bin/configinit.sh
index 15f1a17ca96e..0b679d8382c7 100755
--- a/tools/testing/selftests/rcutorture/bin/configinit.sh
+++ b/tools/testing/selftests/rcutorture/bin/configinit.sh
@@ -51,7 +51,7 @@ then
mkdir $builddir
fi
else
- echo Bad build directory: \"$builddir\"
+ echo Bad build directory: \"$buildloc\"
exit 2
fi
fi
--
2.14.1
From: Dan Carpenter <[email protected]>
[ Upstream commit 65a12b3aafed5fc59f4ce41b22b752b1729e6701 ]
We should be finishing the loop with timeout set to zero but because
this is a post-op we finish with timeout == -1.
Fixes: 1082e2703a2d ("ASoC: NUC900/audio: add nuc900 audio driver support")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/nuc900/nuc900-ac97.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/sound/soc/nuc900/nuc900-ac97.c b/sound/soc/nuc900/nuc900-ac97.c
index f2f67942b229..84a4fc84d688 100644
--- a/sound/soc/nuc900/nuc900-ac97.c
+++ b/sound/soc/nuc900/nuc900-ac97.c
@@ -67,7 +67,7 @@ static unsigned short nuc900_ac97_read(struct snd_ac97 *ac97,
/* polling the AC_R_FINISH */
while (!(AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_R_FINISH)
- && timeout--)
+ && --timeout)
mdelay(1);
if (!timeout) {
@@ -121,7 +121,7 @@ static void nuc900_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
/* polling the AC_W_FINISH */
while ((AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_W_FINISH)
- && timeout--)
+ && --timeout)
mdelay(1);
if (!timeout)
--
2.14.1
From: Stephen Hemminger <[email protected]>
[ Upstream commit 72d24955b44a4039db54a1c252b5031969eeaac3 ]
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/veth.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/veth.c b/drivers/net/veth.c
index 32ce1cd64d51..b6b322828549 100644
--- a/drivers/net/veth.c
+++ b/drivers/net/veth.c
@@ -382,6 +382,9 @@ static int veth_newlink(struct net *src_net, struct net_device *dev,
if (ifmp && (dev->ifindex != 0))
peer->ifindex = ifmp->ifi_index;
+ peer->gso_max_size = dev->gso_max_size;
+ peer->gso_max_segs = dev->gso_max_segs;
+
err = register_netdevice(peer);
put_net(net);
net = NULL;
--
2.14.1
From: Dedy Lansky <[email protected]>
[ Upstream commit 0f6edfe2bbbb59d161580cb4870fcc46f5490f85 ]
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <[email protected]>
Signed-off-by: Maya Erez <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/wil6210/main.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index c5676841fd12..e27dd5017218 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -59,9 +59,15 @@ void wil_memcpy_fromio_32(void *dst, const volatile void __iomem *src,
u32 *d = dst;
const volatile u32 __iomem *s = src;
- /* size_t is unsigned, if (count%4 != 0) it will wrap */
- for (count += 4; count > 4; count -= 4)
+ for (; count >= 4; count -= 4)
*d++ = __raw_readl(s++);
+
+ if (unlikely(count)) {
+ /* count can be 1..3 */
+ u32 tmp = __raw_readl(s);
+
+ memcpy(d, &tmp, count);
+ }
}
void wil_memcpy_toio_32(volatile void __iomem *dst, const void *src,
@@ -70,8 +76,16 @@ void wil_memcpy_toio_32(volatile void __iomem *dst, const void *src,
volatile u32 __iomem *d = dst;
const u32 *s = src;
- for (count += 4; count > 4; count -= 4)
+ for (; count >= 4; count -= 4)
__raw_writel(*s++, d++);
+
+ if (unlikely(count)) {
+ /* count can be 1..3 */
+ u32 tmp = 0;
+
+ memcpy(&tmp, s, count);
+ __raw_writel(tmp, d);
+ }
}
static void wil_disconnect_cid(struct wil6210_priv *wil, int cid)
--
2.14.1
From: Masami Hiramatsu <[email protected]>
[ Upstream commit d0381c81c2f782fa2131178d11e0cfb23d50d631 ]
Set the pages which is used for kprobes' singlestep buffer
and optprobe's trampoline instruction buffer to readonly.
This can prevent unexpected (or unintended) instruction
modification.
This also passes rodata_test as below.
Without this patch, rodata_test shows a warning:
WARNING: CPU: 0 PID: 1 at arch/x86/mm/dump_pagetables.c:235 note_page+0x7a9/0xa20
x86/mm: Found insecure W+X mapping at address ffffffffa0000000/0xffffffffa0000000
With this fix, no W+X pages are found:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
rodata_test: all tests were successful
Reported-by: Andrey Ryabinin <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Anil S Keshavamurthy <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: David S . Miller <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ye Xiaolong <[email protected]>
Link: http://lkml.kernel.org/r/149076375592.22469.14174394514338612247.stgit@devbox
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/kprobes/core.c | 4 ++++
arch/x86/kernel/kprobes/opt.c | 3 +++
2 files changed, 7 insertions(+)
diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c
index 422b76ab0374..78f221ab8593 100644
--- a/arch/x86/kernel/kprobes/core.c
+++ b/arch/x86/kernel/kprobes/core.c
@@ -378,6 +378,8 @@ static int arch_copy_kprobe(struct kprobe *p)
{
int ret;
+ set_memory_rw((unsigned long)p->ainsn.insn & PAGE_MASK, 1);
+
/* Copy an instruction with recovering if other optprobe modifies it.*/
ret = __copy_instruction(p->ainsn.insn, p->addr);
if (!ret)
@@ -392,6 +394,8 @@ static int arch_copy_kprobe(struct kprobe *p)
else
p->ainsn.boostable = -1;
+ set_memory_ro((unsigned long)p->ainsn.insn & PAGE_MASK, 1);
+
/* Check whether the instruction modifies Interrupt Flag or not */
p->ainsn.if_modifier = is_IF_modifier(p->ainsn.insn);
diff --git a/arch/x86/kernel/kprobes/opt.c b/arch/x86/kernel/kprobes/opt.c
index cdb672c3049b..aec5dfa8b7e1 100644
--- a/arch/x86/kernel/kprobes/opt.c
+++ b/arch/x86/kernel/kprobes/opt.c
@@ -344,6 +344,7 @@ int arch_prepare_optimized_kprobe(struct optimized_kprobe *op)
}
buf = (u8 *)op->optinsn.insn;
+ set_memory_rw((unsigned long)buf & PAGE_MASK, 1);
/* Copy instructions into the out-of-line buffer */
ret = copy_optimized_instructions(buf + TMPL_END_IDX, op->kp.addr);
@@ -366,6 +367,8 @@ int arch_prepare_optimized_kprobe(struct optimized_kprobe *op)
synthesize_reljump(buf + TMPL_END_IDX + op->optinsn.size,
(u8 *)op->kp.addr + op->optinsn.size);
+ set_memory_ro((unsigned long)buf & PAGE_MASK, 1);
+
flush_icache_range((unsigned long) buf,
(unsigned long) buf + TMPL_END_IDX +
op->optinsn.size + RELATIVEJUMP_SIZE);
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit dcb407b257af06fa58b0544ec01ec9e0d3927e02 ]
Currently BCLK inverting is only handled when the DAI format is
DSP, but the BCLK may be inverted in any supported mode. Without
this using this CODEC in any other mode than DSP with the BCLK
inverted leads to bad sampling timing and very poor audio quality.
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
sound/soc/codecs/tlv320aic31xx.c | 28 ++++++++++++++++++----------
1 file changed, 18 insertions(+), 10 deletions(-)
diff --git a/sound/soc/codecs/tlv320aic31xx.c b/sound/soc/codecs/tlv320aic31xx.c
index 93de5dd0a7b9..fbeb34e87032 100644
--- a/sound/soc/codecs/tlv320aic31xx.c
+++ b/sound/soc/codecs/tlv320aic31xx.c
@@ -845,6 +845,18 @@ static int aic31xx_set_dai_fmt(struct snd_soc_dai *codec_dai,
return -EINVAL;
}
+ /* signal polarity */
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ iface_reg2 |= AIC31XX_BCLKINV_MASK;
+ break;
+ default:
+ dev_err(codec->dev, "Invalid DAI clock signal polarity\n");
+ return -EINVAL;
+ }
+
/* interface format */
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_I2S:
@@ -852,16 +864,12 @@ static int aic31xx_set_dai_fmt(struct snd_soc_dai *codec_dai,
case SND_SOC_DAIFMT_DSP_A:
dsp_a_val = 0x1;
case SND_SOC_DAIFMT_DSP_B:
- /* NOTE: BCLKINV bit value 1 equas NB and 0 equals IB */
- switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
- case SND_SOC_DAIFMT_NB_NF:
- iface_reg2 |= AIC31XX_BCLKINV_MASK;
- break;
- case SND_SOC_DAIFMT_IB_NF:
- break;
- default:
- return -EINVAL;
- }
+ /*
+ * NOTE: This CODEC samples on the falling edge of BCLK in
+ * DSP mode, this is inverted compared to what most DAIs
+ * expect, so we invert for this mode
+ */
+ iface_reg2 ^= AIC31XX_BCLKINV_MASK;
iface_reg1 |= (AIC31XX_DSP_MODE <<
AIC31XX_IFACE1_DATATYPE_SHIFT);
break;
--
2.14.1
From: Jagdish Gediya <[email protected]>
[ Upstream commit bccb06c353af3764ca86d9da47652458e6c2eb41 ]
Bufnum mask is used to calculate page position in the internal SRAM.
As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.
Signed-off-by: Jagdish Gediya <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/mtd/nand/fsl_ifc_nand.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c
index 2338124dd05f..fdc78b201780 100644
--- a/drivers/mtd/nand/fsl_ifc_nand.c
+++ b/drivers/mtd/nand/fsl_ifc_nand.c
@@ -988,6 +988,13 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
if (ver == FSL_IFC_V1_1_0)
fsl_ifc_sram_init(priv);
+ /*
+ * As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
+ * versions which had 8KB. Hence bufnum mask needs to be updated.
+ */
+ if (ctrl->version >= FSL_IFC_VERSION_2_0_0)
+ priv->bufnum_mask = (priv->bufnum_mask * 2) + 1;
+
return 0;
}
--
2.14.1
From: Johannes Thumshirn <[email protected]>
[ Upstream commit 28676d869bbb5257b5f14c0c95ad3af3a7019dd5 ]
Check for a valid direction before starting the request, otherwise we
risk running into an assertion in the scsi midlayer checking for valid
requests.
[mkp: fixed typo]
Signed-off-by: Johannes Thumshirn <[email protected]>
Link: http://www.spinics.net/lists/linux-scsi/msg104400.html
Reported-by: Dmitry Vyukov <[email protected]>
Signed-off-by: Hannes Reinecke <[email protected]>
Tested-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/sg.c | 46 ++++++++++++++++++++++++++++++++++------------
1 file changed, 34 insertions(+), 12 deletions(-)
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index 783040af3ead..bba2dcd4f324 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -674,18 +674,14 @@ sg_write(struct file *filp, const char __user *buf, size_t count, loff_t * ppos)
* is a non-zero input_size, so emit a warning.
*/
if (hp->dxfer_direction == SG_DXFER_TO_FROM_DEV) {
- static char cmd[TASK_COMM_LEN];
- if (strcmp(current->comm, cmd)) {
- printk_ratelimited(KERN_WARNING
- "sg_write: data in/out %d/%d bytes "
- "for SCSI command 0x%x-- guessing "
- "data in;\n program %s not setting "
- "count and/or reply_len properly\n",
- old_hdr.reply_len - (int)SZ_SG_HEADER,
- input_size, (unsigned int) cmnd[0],
- current->comm);
- strcpy(cmd, current->comm);
- }
+ printk_ratelimited(KERN_WARNING
+ "sg_write: data in/out %d/%d bytes "
+ "for SCSI command 0x%x-- guessing "
+ "data in;\n program %s not setting "
+ "count and/or reply_len properly\n",
+ old_hdr.reply_len - (int)SZ_SG_HEADER,
+ input_size, (unsigned int) cmnd[0],
+ current->comm);
}
k = sg_common_write(sfp, srp, cmnd, sfp->timeout, blocking);
return (k < 0) ? k : count;
@@ -764,6 +760,29 @@ sg_new_write(Sg_fd *sfp, struct file *file, const char __user *buf,
return count;
}
+static bool sg_is_valid_dxfer(sg_io_hdr_t *hp)
+{
+ switch (hp->dxfer_direction) {
+ case SG_DXFER_NONE:
+ if (hp->dxferp || hp->dxfer_len > 0)
+ return false;
+ return true;
+ case SG_DXFER_TO_DEV:
+ case SG_DXFER_FROM_DEV:
+ case SG_DXFER_TO_FROM_DEV:
+ if (!hp->dxferp || hp->dxfer_len == 0)
+ return false;
+ return true;
+ case SG_DXFER_UNKNOWN:
+ if ((!hp->dxferp && hp->dxfer_len) ||
+ (hp->dxferp && hp->dxfer_len == 0))
+ return false;
+ return true;
+ default:
+ return false;
+ }
+}
+
static int
sg_common_write(Sg_fd * sfp, Sg_request * srp,
unsigned char *cmnd, int timeout, int blocking)
@@ -784,6 +803,9 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
"sg_common_write: scsi opcode=0x%02x, cmd_size=%d\n",
(int) cmnd[0], (int) hp->cmd_len));
+ if (!sg_is_valid_dxfer(hp))
+ return -EINVAL;
+
k = sg_start_req(srp, cmnd);
if (k) {
SCSI_LOG_TIMEOUT(1, sg_printk(KERN_INFO, sfp->parentdp,
--
2.14.1
From: Lorenzo Colitti <[email protected]>
[ Upstream commit be8f8284cd897af2482d4e54fbc2bdfc15557259 ]
Currently it is possible to add or update socket policies, but
not clear them. Therefore, once a socket policy has been applied,
the socket cannot be used for unencrypted traffic.
This patch allows (privileged) users to clear socket policies by
passing in a NULL pointer and zero length argument to the
{IP,IPV6}_{IPSEC,XFRM}_POLICY setsockopts. This results in both
the incoming and outgoing policies being cleared.
The simple approach taken in this patch cannot clear socket
policies in only one direction. If desired this could be added
in the future, for example by continuing to pass in a length of
zero (which currently is guaranteed to return EMSGSIZE) and
making the policy be a pointer to an integer that contains one
of the XFRM_POLICY_{IN,OUT} enum values.
An alternative would have been to interpret the length as a
signed integer and use XFRM_POLICY_IN (i.e., 0) to clear the
input policy and -XFRM_POLICY_OUT (i.e., -1) to clear the output
policy.
Tested: https://android-review.googlesource.com/539816
Signed-off-by: Lorenzo Colitti <[email protected]>
Signed-off-by: Steffen Klassert <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/xfrm/xfrm_policy.c | 2 +-
net/xfrm/xfrm_state.c | 7 +++++++
2 files changed, 8 insertions(+), 1 deletion(-)
diff --git a/net/xfrm/xfrm_policy.c b/net/xfrm/xfrm_policy.c
index fb84ff4aeee7..d81f27046582 100644
--- a/net/xfrm/xfrm_policy.c
+++ b/net/xfrm/xfrm_policy.c
@@ -1292,7 +1292,7 @@ EXPORT_SYMBOL(xfrm_policy_delete);
int xfrm_sk_policy_insert(struct sock *sk, int dir, struct xfrm_policy *pol)
{
- struct net *net = xp_net(pol);
+ struct net *net = sock_net(sk);
struct xfrm_policy *old_pol;
#ifdef CONFIG_XFRM_SUB_POLICY
diff --git a/net/xfrm/xfrm_state.c b/net/xfrm/xfrm_state.c
index de971b6d38c5..60e04edc4963 100644
--- a/net/xfrm/xfrm_state.c
+++ b/net/xfrm/xfrm_state.c
@@ -1845,6 +1845,13 @@ int xfrm_user_policy(struct sock *sk, int optname, u8 __user *optval, int optlen
struct xfrm_mgr *km;
struct xfrm_policy *pol = NULL;
+ if (!optval && !optlen) {
+ xfrm_sk_policy_insert(sk, XFRM_POLICY_IN, NULL);
+ xfrm_sk_policy_insert(sk, XFRM_POLICY_OUT, NULL);
+ __sk_dst_reset(sk);
+ return 0;
+ }
+
if (optlen <= 0 || optlen > PAGE_SIZE)
return -EMSGSIZE;
--
2.14.1
From: Miquel Raynal <[email protected]>
[ Upstream commit df467899da0b71465760b4e35127bce837244eee ]
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.
Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/mtd/nand/nand_base.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 7eddb1e95de3..c8f20467ff1d 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -600,7 +600,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
chip->cmd_ctrl(mtd, readcmd, ctrl);
ctrl &= ~NAND_CTRL_CHANGE;
}
- chip->cmd_ctrl(mtd, command, ctrl);
+ if (command != NAND_CMD_NONE)
+ chip->cmd_ctrl(mtd, command, ctrl);
/* Address cycle, when necessary */
ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
@@ -629,6 +630,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
*/
switch (command) {
+ case NAND_CMD_NONE:
case NAND_CMD_PAGEPROG:
case NAND_CMD_ERASE1:
case NAND_CMD_ERASE2:
@@ -691,7 +693,9 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
}
/* Command latch cycle */
- chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
+ if (command != NAND_CMD_NONE)
+ chip->cmd_ctrl(mtd, command,
+ NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
if (column != -1 || page_addr != -1) {
int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
@@ -724,6 +728,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
*/
switch (command) {
+ case NAND_CMD_NONE:
case NAND_CMD_CACHEDPROG:
case NAND_CMD_PAGEPROG:
case NAND_CMD_ERASE1:
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit e153db03c6b7a035c797bcdf35262586f003ee93 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/am335x-pepper.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts
index 0d35ab64641c..ac3ca3636405 100644
--- a/arch/arm/boot/dts/am335x-pepper.dts
+++ b/arch/arm/boot/dts/am335x-pepper.dts
@@ -138,7 +138,7 @@
&audio_codec {
status = "okay";
- gpio-reset = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
AVDD-supply = <&ldo3_reg>;
IOVDD-supply = <&ldo3_reg>;
DRVDD-supply = <&ldo3_reg>;
--
2.14.1
From: "Paul E. McKenney" <[email protected]>
[ Upstream commit a0982dfa03efca6c239c52cabebcea4afb93ea6b ]
The rcutorture test suite occasionally provokes a splat due to invoking
resched_cpu() on an offline CPU:
WARNING: CPU: 2 PID: 8 at /home/paulmck/public_git/linux-rcu/arch/x86/kernel/smp.c:128 native_smp_send_reschedule+0x37/0x40
Modules linked in:
CPU: 2 PID: 8 Comm: rcu_preempt Not tainted 4.14.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
task: ffff902ede9daf00 task.stack: ffff96c50010c000
RIP: 0010:native_smp_send_reschedule+0x37/0x40
RSP: 0018:ffff96c50010fdb8 EFLAGS: 00010096
RAX: 000000000000002e RBX: ffff902edaab4680 RCX: 0000000000000003
RDX: 0000000080000003 RSI: 0000000000000000 RDI: 00000000ffffffff
RBP: ffff96c50010fdb8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 00000000299f36ae R12: 0000000000000001
R13: ffffffff9de64240 R14: 0000000000000001 R15: ffffffff9de64240
FS: 0000000000000000(0000) GS:ffff902edfc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f7d4c642 CR3: 000000001e0e2000 CR4: 00000000000006e0
Call Trace:
resched_curr+0x8f/0x1c0
resched_cpu+0x2c/0x40
rcu_implicit_dynticks_qs+0x152/0x220
force_qs_rnp+0x147/0x1d0
? sync_rcu_exp_select_cpus+0x450/0x450
rcu_gp_kthread+0x5a9/0x950
kthread+0x142/0x180
? force_qs_rnp+0x1d0/0x1d0
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x27/0x40
Code: 14 01 0f 92 c0 84 c0 74 14 48 8b 05 14 4f f4 00 be fd 00 00 00 ff 90 a0 00 00 00 5d c3 89 fe 48 c7 c7 38 89 ca 9d e8 e5 56 08 00 <0f> ff 5d c3 0f 1f 44 00 00 8b 05 52 9e 37 02 85 c0 75 38 55 48
---[ end trace 26df9e5df4bba4ac ]---
This splat cannot be generated by expedited grace periods because they
always invoke resched_cpu() on the current CPU, which is good because
expedited grace periods require that resched_cpu() unconditionally
succeed. However, other parts of RCU can tolerate resched_cpu() acting
as a no-op, at least as long as it doesn't happen too often.
This commit therefore makes resched_cpu() invoke resched_curr() only if
the CPU is either online or is the current CPU.
Signed-off-by: Paul E. McKenney <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/sched/core.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/kernel/sched/core.c b/kernel/sched/core.c
index 5c64c714ad08..3ff883ec2e52 100644
--- a/kernel/sched/core.c
+++ b/kernel/sched/core.c
@@ -633,7 +633,8 @@ void resched_cpu(int cpu)
unsigned long flags;
raw_spin_lock_irqsave(&rq->lock, flags);
- resched_curr(rq);
+ if (cpu_online(cpu) || cpu == smp_processor_id())
+ resched_curr(rq);
raw_spin_unlock_irqrestore(&rq->lock, flags);
}
--
2.14.1
From: "Andrew F. Davis" <[email protected]>
[ Upstream commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2b9 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/omap3-n900.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 6e1cea55d0ec..70bb75ec9c7d 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -435,7 +435,7 @@
tlv320aic3x: tlv320aic3x@18 {
compatible = "ti,tlv320aic3x";
reg = <0x18>;
- gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
ai3x-gpio-func = <
0 /* AIC3X_GPIO1_FUNC_DISABLED */
5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
@@ -452,7 +452,7 @@
tlv320aic3x_aux: tlv320aic3x@19 {
compatible = "ti,tlv320aic3x";
reg = <0x19>;
- gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
+ reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
AVDD-supply = <&vmmc2>;
DRVDD-supply = <&vmmc2>;
--
2.14.1
From: Alexander Kochetkov <[email protected]>
[ Upstream commit 500d0aa918a2ea6bb918fee8adcf27dc2912bcd1 ]
The clocksource and the sched_clock provided by the arm_global_timer
are quite unstable because their rates depend on the cpu frequency.
On the other side, the arm_global_timer has a higher rating than the
rockchip_timer, it will be selected by default by the time framework
while we want to use the stable rockchip clocksource.
Let's disable the arm_global_timer in order to have the rockchip
clocksource selected by default.
Signed-off-by: Alexander Kochetkov <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/rk3188.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index ddaada788b45..72b0b4cb538f 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -404,6 +404,7 @@
&global_timer {
interrupts = <GIC_PPI 11 0xf04>;
+ status = "disabled";
};
&local_timer {
--
2.14.1
From: Masami Hiramatsu <[email protected]>
[ Upstream commit bd0b90676c30fe640e7ead919b3e38846ac88ab7 ]
Fix the kprobe-booster not to boost far call instruction,
because a call may store the address in the single-step
execution buffer to the stack, which should be modified
after single stepping.
Currently, this instruction will be filtered as not
boostable in resume_execution(), so this is not a
critical issue.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Anil S Keshavamurthy <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: David S . Miller <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Ye Xiaolong <[email protected]>
Link: http://lkml.kernel.org/r/149076340615.22469.14066273186134229909.stgit@devbox
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/x86/kernel/kprobes/core.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/x86/kernel/kprobes/core.c b/arch/x86/kernel/kprobes/core.c
index b6547a441bad..422b76ab0374 100644
--- a/arch/x86/kernel/kprobes/core.c
+++ b/arch/x86/kernel/kprobes/core.c
@@ -196,6 +196,8 @@ retry:
return (opcode != 0x62 && opcode != 0x67);
case 0x70:
return 0; /* can't boost conditional jump */
+ case 0x90:
+ return opcode != 0x9a; /* can't boost call far */
case 0xc0:
/* can't boost software-interruptions */
return (0xc1 < opcode && opcode < 0xcc) || opcode == 0xcf;
--
2.14.1
From: Liam Beguin <[email protected]>
[ Upstream commit 9a1c779e6b06855e41099caa6f15b3b584dfa88c ]
This patch forces the frambuffer size to be aligned on kernel pages.
During the board startup, the splash screed did appear;
the "ts_test" program or our application were not able to start.
The following error message was reported:
error: failed to map framebuffer device to memory.
LinuxFB: driver cannot connect
The issue was discovered, on the LPC32xx platform, during the migration
of the LCD definition from the board file to the device tree.
Signed-off-by: Liam Beguin <[email protected]>
Signed-off-by: Sylvain Lemieux <[email protected]>
Cc: Vladimir Zapolskiy <[email protected]>
Cc: Russell King <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/video/fbdev/amba-clcd.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/video/fbdev/amba-clcd.c b/drivers/video/fbdev/amba-clcd.c
index 6ad23bd3523a..7fd2f3f7ef7c 100644
--- a/drivers/video/fbdev/amba-clcd.c
+++ b/drivers/video/fbdev/amba-clcd.c
@@ -757,8 +757,8 @@ static int clcdfb_of_dma_setup(struct clcd_fb *fb)
if (err)
return err;
- framesize = fb->panel->mode.xres * fb->panel->mode.yres *
- fb->panel->bpp / 8;
+ framesize = PAGE_ALIGN(fb->panel->mode.xres * fb->panel->mode.yres *
+ fb->panel->bpp / 8);
fb->fb.screen_base = dma_alloc_coherent(&fb->dev->dev, framesize,
&dma, GFP_KERNEL);
if (!fb->fb.screen_base)
--
2.14.1
From: Jiri Kosina <[email protected]>
[ Upstream commit 9abd04af951e5734c9d5cfee9b49790844b734cf ]
ELO devices have one Button usage in GenDesk field, which makes hid-input map
it to BTN_LEFT; that confuses userspace, which then considers the device to be
a mouse/touchpad instead of touchscreen.
Fix that by unmapping BTN_LEFT and keeping only BTN_TOUCH in place.
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-elo.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/hid/hid-elo.c b/drivers/hid/hid-elo.c
index d0c8a1c1e1fe..2fc43ad7f0b6 100644
--- a/drivers/hid/hid-elo.c
+++ b/drivers/hid/hid-elo.c
@@ -42,6 +42,12 @@ static void elo_input_configured(struct hid_device *hdev,
{
struct input_dev *input = hidinput->input;
+ /*
+ * ELO devices have one Button usage in GenDesk field, which makes
+ * hid-input map it to BTN_LEFT; that confuses userspace, which then
+ * considers the device to be a mouse/touchpad instead of touchscreen.
+ */
+ clear_bit(BTN_LEFT, input->keybit);
set_bit(BTN_TOUCH, input->keybit);
set_bit(ABS_PRESSURE, input->absbit);
input_set_abs_params(input, ABS_PRESSURE, 0, 256, 0, 0);
--
2.14.1
From: Hannes Reinecke <[email protected]>
[ Upstream commit 97d27b0dd015e980ade63fda111fd1353276e28b ]
sg_remove_sfp_usercontext() is clearing any sg requests, but needs to
take 'rq_list_lock' when modifying the list.
Reported-by: Christoph Hellwig <[email protected]>
Signed-off-by: Hannes Reinecke <[email protected]>
Reviewed-by: Johannes Thumshirn <[email protected]>
Tested-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/sg.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index bba2dcd4f324..cab426720144 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -535,6 +535,7 @@ sg_read(struct file *filp, char __user *buf, size_t count, loff_t * ppos)
} else
count = (old_hdr->result == 0) ? 0 : -EIO;
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
retval = count;
free_old_hdr:
kfree(old_hdr);
@@ -575,6 +576,7 @@ sg_new_read(Sg_fd * sfp, char __user *buf, size_t count, Sg_request * srp)
}
err_out:
err2 = sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return err ? : err2 ? : count;
}
@@ -811,6 +813,7 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
SCSI_LOG_TIMEOUT(1, sg_printk(KERN_INFO, sfp->parentdp,
"sg_common_write: start_req err=%d\n", k));
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return k; /* probably out of space --> ENOMEM */
}
if (atomic_read(&sdp->detaching)) {
@@ -823,6 +826,7 @@ sg_common_write(Sg_fd * sfp, Sg_request * srp,
}
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
return -ENODEV;
}
@@ -1353,6 +1357,7 @@ sg_rq_end_io_usercontext(struct work_struct *work)
struct sg_fd *sfp = srp->parentfp;
sg_finish_rem_req(srp);
+ sg_remove_request(sfp, srp);
kref_put(&sfp->f_ref, sg_remove_sfp);
}
@@ -1902,8 +1907,6 @@ sg_finish_rem_req(Sg_request *srp)
else
sg_remove_scat(sfp, req_schp);
- sg_remove_request(sfp, srp);
-
return ret;
}
@@ -2250,12 +2253,17 @@ sg_remove_sfp_usercontext(struct work_struct *work)
struct sg_fd *sfp = container_of(work, struct sg_fd, ew.work);
struct sg_device *sdp = sfp->parentdp;
Sg_request *srp;
+ unsigned long iflags;
/* Cleanup any responses which were never read(). */
+ write_lock_irqsave(&sfp->rq_list_lock, iflags);
while (!list_empty(&sfp->rq_list)) {
srp = list_first_entry(&sfp->rq_list, Sg_request, entry);
sg_finish_rem_req(srp);
+ list_del(&srp->entry);
+ srp->parentfp = NULL;
}
+ write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
if (sfp->reserve.bufflen > 0) {
SCSI_LOG_TIMEOUT(6, sg_printk(KERN_INFO, sdp,
--
2.14.1
From: David Carrillo-Cisneros <[email protected]>
[ Upstream commit 0973ad97c187e06aece61f685b9c3b2d93290a73 ]
Session sets a number parameters that rely on evlist. These parameters
are not used in pipe-mode and should not be set, since evlist is
unavailable. Fix that.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Check if file != NULL in perf_session__new(), like when used by builtin-top.c ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/session.c | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)
diff --git a/tools/perf/util/session.c b/tools/perf/util/session.c
index e798b58971bf..dc3d3b1b813e 100644
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -108,8 +108,14 @@ struct perf_session *perf_session__new(struct perf_data_file *file,
if (perf_session__open(session) < 0)
goto out_close;
- perf_session__set_id_hdr_size(session);
- perf_session__set_comm_exec(session);
+ /*
+ * set session attributes that are present in perf.data
+ * but not in pipe-mode.
+ */
+ if (!file->is_pipe) {
+ perf_session__set_id_hdr_size(session);
+ perf_session__set_comm_exec(session);
+ }
}
}
@@ -122,7 +128,11 @@ struct perf_session *perf_session__new(struct perf_data_file *file,
pr_warning("Cannot read kernel map\n");
}
- if (tool && tool->ordering_requires_timestamps &&
+ /*
+ * In pipe-mode, evlist is empty until PERF_RECORD_HEADER_ATTR is
+ * processed, so perf_evlist__sample_id_all is not meaningful here.
+ */
+ if ((!file || !file->is_pipe) && tool && tool->ordering_requires_timestamps &&
tool->ordered_events && !perf_evlist__sample_id_all(session->evlist)) {
dump_printf("WARNING: No sample_id_all support, falling back to unordered processing\n");
tool->ordered_events = false;
--
2.14.1
From: Christopher James Halse Rogers <[email protected]>
[ Upstream commit a294043b2fbd8de69d161457ed0c7a4026bbfa5a ]
Any use of the framebuffer will migrate it to VRAM, which is not sensible for
an imported dma-buf.
v2: Use DRM_DEBUG_KMS to prevent userspace accidentally spamming dmesg.
Reviewed-by: Michel Dänzer <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Christopher James Halse Rogers <[email protected]>
CC: [email protected]
Signed-off-by: Alex Deucher <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/radeon/radeon_display.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c
index 21e6e9745d00..1938de582717 100644
--- a/drivers/gpu/drm/radeon/radeon_display.c
+++ b/drivers/gpu/drm/radeon/radeon_display.c
@@ -1320,6 +1320,12 @@ radeon_user_framebuffer_create(struct drm_device *dev,
return ERR_PTR(-ENOENT);
}
+ /* Handle is imported dma-buf, so cannot be migrated to VRAM for scanout */
+ if (obj->import_attach) {
+ DRM_DEBUG_KMS("Cannot create framebuffer from imported dma_buf\n");
+ return ERR_PTR(-EINVAL);
+ }
+
radeon_fb = kzalloc(sizeof(*radeon_fb), GFP_KERNEL);
if (radeon_fb == NULL) {
drm_gem_object_unreference_unlocked(obj);
--
2.14.1
From: Yuyang Du <[email protected]>
[ Upstream commit 9f20dfb44d03745d0d3cef2ffb3abf8d8024fa61 ]
This fixes the commit: 1cd8fd2887e1 ("usb: gadget: dummy_hcd: add
SuperSpeed support").
In the case of ClearPortFeature and USB_PORT_FEAT_POWER, simply clear
the right bit regardless of what the wValue is.
Acked-by: Alan Stern <[email protected]>
Signed-off-by: Yuyang Du <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/usb/gadget/udc/dummy_hcd.c | 20 ++++++++------------
1 file changed, 8 insertions(+), 12 deletions(-)
diff --git a/drivers/usb/gadget/udc/dummy_hcd.c b/drivers/usb/gadget/udc/dummy_hcd.c
index 783715a9e399..215441690d32 100644
--- a/drivers/usb/gadget/udc/dummy_hcd.c
+++ b/drivers/usb/gadget/udc/dummy_hcd.c
@@ -2001,16 +2001,13 @@ static int dummy_hub_control(
}
break;
case USB_PORT_FEAT_POWER:
- if (hcd->speed == HCD_USB3) {
- if (dum_hcd->port_status & USB_PORT_STAT_POWER)
- dev_dbg(dummy_dev(dum_hcd),
- "power-off\n");
- } else
- if (dum_hcd->port_status &
- USB_SS_PORT_STAT_POWER)
- dev_dbg(dummy_dev(dum_hcd),
- "power-off\n");
- /* FALLS THROUGH */
+ dev_dbg(dummy_dev(dum_hcd), "power-off\n");
+ if (hcd->speed == HCD_USB3)
+ dum_hcd->port_status &= ~USB_SS_PORT_STAT_POWER;
+ else
+ dum_hcd->port_status &= ~USB_PORT_STAT_POWER;
+ set_link_state(dum_hcd);
+ break;
default:
dum_hcd->port_status &= ~(1 << wValue);
set_link_state(dum_hcd);
@@ -2181,14 +2178,13 @@ static int dummy_hub_control(
if ((dum_hcd->port_status &
USB_SS_PORT_STAT_POWER) != 0) {
dum_hcd->port_status |= (1 << wValue);
- set_link_state(dum_hcd);
}
} else
if ((dum_hcd->port_status &
USB_PORT_STAT_POWER) != 0) {
dum_hcd->port_status |= (1 << wValue);
- set_link_state(dum_hcd);
}
+ set_link_state(dum_hcd);
}
break;
case GetPortErrorCount:
--
2.14.1
From: David Carrillo-Cisneros <[email protected]>
[ Upstream commit 1e0d4f0200e4dbdfc38d818f329d8a0955f7c6f5 ]
__perf_session__process_pipe_events reuses the same memory buffer to
process all events in the pipe.
When reordering is needed (e.g. -b option), events are not immediately
flushed, but kept around until reordering is possible, causing
memory corruption.
The problem is usually observed by a "Unknown sample error" output. It
can easily be reproduced by:
perf record -o - noploop | perf inject -b > output
Committer testing:
Before:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [8297] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [8297] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
Warning:
Found 1 unknown events!
Is this an older tool processing a perf.data file generated by a more recent tool?
If that is not the case, consider reporting to [email protected].
$
After:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [9027] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [9027] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
no symbols found in /usr/bin/stress, maybe install a debug package?
no symbols found in /usr/bin/stress, maybe install a debug package?
$
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/ordered-events.c | 3 ++-
tools/perf/util/session.c | 1 +
2 files changed, 3 insertions(+), 1 deletion(-)
diff --git a/tools/perf/util/ordered-events.c b/tools/perf/util/ordered-events.c
index fd4be94125fb..e2c53bb0e476 100644
--- a/tools/perf/util/ordered-events.c
+++ b/tools/perf/util/ordered-events.c
@@ -80,7 +80,7 @@ static union perf_event *dup_event(struct ordered_events *oe,
static void free_dup_event(struct ordered_events *oe, union perf_event *event)
{
- if (oe->copy_on_queue) {
+ if (event && oe->copy_on_queue) {
oe->cur_alloc_size -= event->header.size;
free(event);
}
@@ -151,6 +151,7 @@ void ordered_events__delete(struct ordered_events *oe, struct ordered_event *eve
list_move(&event->list, &oe->cache);
oe->nr_events--;
free_dup_event(oe, event->event);
+ event->event = NULL;
}
static int __ordered_events__flush(struct perf_session *s,
diff --git a/tools/perf/util/session.c b/tools/perf/util/session.c
index 80dbba095f30..e798b58971bf 100644
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -1080,6 +1080,7 @@ static int __perf_session__process_pipe_events(struct perf_session *session,
buf = malloc(cur_size);
if (!buf)
return -errno;
+ ordered_events__set_copy_on_queue(oe, true);
more:
event = buf;
err = readn(fd, event, sizeof(struct perf_event_header));
--
2.14.1
From: Vincent Stehlé <[email protected]>
[ Upstream commit 0c08aaf873174c95e674cf21ffcd041c589d2e5b ]
ISL9305_MAX_REGULATOR is the last index used to access the init_data[]
array, so we need to add one to this last index to obtain the necessary
array size.
This fixes the following smatch error:
drivers/regulator/isl9305.c:160 isl9305_i2c_probe() error: buffer overflow 'pdata->init_data' 3 <= 3
Fixes: dec38b5ce6a9edb4 ("regulator: isl9305: Add Intersil ISL9305/H driver")
Signed-off-by: Vincent Stehlé <[email protected]>
Cc: Mark Brown <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/platform_data/isl9305.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/include/linux/platform_data/isl9305.h b/include/linux/platform_data/isl9305.h
index 1419133fa69e..4ac1a070af0a 100644
--- a/include/linux/platform_data/isl9305.h
+++ b/include/linux/platform_data/isl9305.h
@@ -24,7 +24,7 @@
struct regulator_init_data;
struct isl9305_pdata {
- struct regulator_init_data *init_data[ISL9305_MAX_REGULATOR];
+ struct regulator_init_data *init_data[ISL9305_MAX_REGULATOR + 1];
};
#endif
--
2.14.1
From: Andreas Pape <[email protected]>
[ Upstream commit a3a5129e122709306cfa6409781716c2933df99b ]
Consider the following situation which has been found in a test setup:
Gateway B has claimed client C and gateway A has the same backbone
network as B. C sends a broad- or multicast to B and directly after
this packet decides to send another packet to A due to a better TQ
value. B will forward the broad-/multicast into the backbone as it is
the responsible gw and after that A will claim C as it has been
chosen by C as the best gateway. If it now happens that A claims C
before it has received the broad-/multicast forwarded by B (due to
backbone topology or due to some delay in B when forwarding the
packet) we get a critical situation: in the current code A will
immediately unclaim C when receiving the multicast due to the
roaming client scenario although the position of C has not changed
in the mesh. If this happens the multi-/broadcast forwarded by B
will be sent back into the mesh by A and we have looping packets
until one of the gateways claims C again.
In order to prevent this, unclaiming of a client due to the roaming
client scenario is only done after a certain time is expired after
the last claim of the client. 100 ms are used here, which should be
slow enough for big backbones and slow gateways but fast enough not
to break the roaming client use case.
Acked-by: Simon Wunderlich <[email protected]>
Signed-off-by: Andreas Pape <[email protected]>
[[email protected]: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/batman-adv/bridge_loop_avoidance.c | 20 ++++++++++++++++----
1 file changed, 16 insertions(+), 4 deletions(-)
diff --git a/net/batman-adv/bridge_loop_avoidance.c b/net/batman-adv/bridge_loop_avoidance.c
index a957c8140721..9906e177131c 100644
--- a/net/batman-adv/bridge_loop_avoidance.c
+++ b/net/batman-adv/bridge_loop_avoidance.c
@@ -1596,10 +1596,22 @@ int batadv_bla_tx(struct batadv_priv *bat_priv, struct sk_buff *skb,
/* if yes, the client has roamed and we have
* to unclaim it.
*/
- batadv_handle_unclaim(bat_priv, primary_if,
- primary_if->net_dev->dev_addr,
- ethhdr->h_source, vid);
- goto allow;
+ if (batadv_has_timed_out(claim->lasttime, 100)) {
+ /* only unclaim if the last claim entry is
+ * older than 100 ms to make sure we really
+ * have a roaming client here.
+ */
+ batadv_dbg(BATADV_DBG_BLA, bat_priv, "bla_tx(): Roaming client %pM detected. Unclaim it.\n",
+ ethhdr->h_source);
+ batadv_handle_unclaim(bat_priv, primary_if,
+ primary_if->net_dev->dev_addr,
+ ethhdr->h_source, vid);
+ goto allow;
+ } else {
+ batadv_dbg(BATADV_DBG_BLA, bat_priv, "bla_tx(): Race for claim %pM detected. Drop packet.\n",
+ ethhdr->h_source);
+ goto handled;
+ }
}
/* check if it is a multicast/broadcast frame */
--
2.14.1
From: John Johansen <[email protected]>
[ Upstream commit 622f6e3265707ebf02ba776ac6e68003bcc31213 ]
The path_max parameter determines the max size of buffers allocated
but it should not be setable at run time. If can be used to cause an
oops
root@ubuntu:~# echo 16777216 > /sys/module/apparmor/parameters/path_max
root@ubuntu:~# cat /sys/module/apparmor/parameters/path_max
Killed
[ 122.141911] BUG: unable to handle kernel paging request at ffff880080945fff
[ 122.143497] IP: [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.144742] PGD 220c067 PUD 0
[ 122.145453] Oops: 0002 [#1] SMP
[ 122.146204] Modules linked in: vmw_vsock_vmci_transport vsock ppdev vmw_balloon snd_ens1371 btusb snd_ac97_codec gameport snd_rawmidi btrtl snd_seq_device ac97_bus btbcm btintel snd_pcm input_leds bluetooth snd_timer snd joydev soundcore serio_raw coretemp shpchp nfit parport_pc i2c_piix4 8250_fintek vmw_vmci parport mac_hid ib_iser rdma_cm iw_cm ib_cm ib_sa ib_mad ib_core ib_addr iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi autofs4 btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd vmwgfx psmouse mptspi ttm mptscsih drm_kms_helper mptbase syscopyarea scsi_transport_spi sysfillrect
[ 122.163365] ahci sysimgblt e1000 fb_sys_fops libahci drm pata_acpi fjes
[ 122.164747] CPU: 3 PID: 1501 Comm: bash Not tainted 4.4.0-59-generic #80-Ubuntu
[ 122.166250] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[ 122.168611] task: ffff88003496aa00 ti: ffff880076474000 task.ti: ffff880076474000
[ 122.170018] RIP: 0010:[<ffffffff81228844>] [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.171525] RSP: 0018:ffff880076477b90 EFLAGS: 00010206
[ 122.172462] RAX: ffff880080945fff RBX: 0000000000000000 RCX: 0000000001000000
[ 122.173709] RDX: 0000000000ffffff RSI: ffff880080946000 RDI: ffff8800348a1010
[ 122.174978] RBP: ffff880076477bb8 R08: ffff880076477c80 R09: 0000000000000000
[ 122.176227] R10: 00007ffffffff000 R11: ffff88007f946000 R12: ffff88007f946000
[ 122.177496] R13: ffff880076477c80 R14: ffff8800348a1010 R15: ffff8800348a2400
[ 122.178745] FS: 00007fd459eb4700(0000) GS:ffff88007b6c0000(0000) knlGS:0000000000000000
[ 122.180176] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 122.181186] CR2: ffff880080945fff CR3: 0000000073422000 CR4: 00000000001406e0
[ 122.182469] Stack:
[ 122.182843] 00ffffff00000001 ffff880080946000 0000000000000000 0000000000000000
[ 122.184409] 00000000570f789c ffff880076477c30 ffffffff81385671 ffff88007a2e7a58
[ 122.185810] 0000000000000000 ffff880076477c88 01000000008a1000 0000000000000000
[ 122.187231] Call Trace:
[ 122.187680] [<ffffffff81385671>] aa_path_name+0x81/0x370
[ 122.188637] [<ffffffff813875dd>] profile_transition+0xbd/0xb80
[ 122.190181] [<ffffffff811af9bc>] ? zone_statistics+0x7c/0xa0
[ 122.191674] [<ffffffff81389b20>] apparmor_bprm_set_creds+0x9b0/0xac0
[ 122.193288] [<ffffffff812e1971>] ? ext4_xattr_get+0x81/0x220
[ 122.194793] [<ffffffff812e800c>] ? ext4_xattr_security_get+0x1c/0x30
[ 122.196392] [<ffffffff813449b9>] ? get_vfs_caps_from_disk+0x69/0x110
[ 122.198004] [<ffffffff81232d4f>] ? mnt_may_suid+0x3f/0x50
[ 122.199737] [<ffffffff81344b03>] ? cap_bprm_set_creds+0xa3/0x600
[ 122.201377] [<ffffffff81346e53>] security_bprm_set_creds+0x33/0x50
[ 122.203024] [<ffffffff81214ce5>] prepare_binprm+0x85/0x190
[ 122.204515] [<ffffffff81216545>] do_execveat_common.isra.33+0x485/0x710
[ 122.206200] [<ffffffff81216a6a>] SyS_execve+0x3a/0x50
[ 122.207615] [<ffffffff81838795>] stub_execve+0x5/0x5
[ 122.208978] [<ffffffff818384f2>] ? entry_SYSCALL_64_fastpath+0x16/0x71
[ 122.210615] Code: f8 31 c0 48 63 c2 83 ea 01 48 c7 45 e8 00 00 00 00 48 01 c6 85 d2 48 c7 45 f0 00 00 00 00 48 89 75 e0 89 55 dc 78 0c 48 8d 46 ff <c6> 46 ff 00 48 89 45 e0 48 8d 55 e0 48 8d 4d dc 48 8d 75 e8 e8
[ 122.217320] RIP [<ffffffff81228844>] d_absolute_path+0x44/0xa0
[ 122.218860] RSP <ffff880076477b90>
[ 122.219919] CR2: ffff880080945fff
[ 122.220936] ---[ end trace 506cdbd85eb6c55e ]---
Reported-by: Tetsuo Handa <[email protected]>
Signed-off-by: John Johansen <[email protected]>
Signed-off-by: James Morris <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/apparmor/lsm.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/security/apparmor/lsm.c b/security/apparmor/lsm.c
index 65ca451a764d..f6be9de35a7f 100644
--- a/security/apparmor/lsm.c
+++ b/security/apparmor/lsm.c
@@ -735,7 +735,7 @@ module_param_named(logsyscall, aa_g_logsyscall, aabool, S_IRUSR | S_IWUSR);
/* Maximum pathname length before accesses will start getting rejected */
unsigned int aa_g_path_max = 2 * PATH_MAX;
-module_param_named(path_max, aa_g_path_max, aauint, S_IRUSR | S_IWUSR);
+module_param_named(path_max, aa_g_path_max, aauint, S_IRUSR);
/* Determines how paranoid loading of policy is and how much verification
* on the loaded policy is done.
--
2.14.1
From: Jan Kara <[email protected]>
[ Upstream commit 71b0576bdb862e964a82c73327cdd1a249c53e67 ]
Currently canceling of delayed work that flushes old data using
cancel_old_flush() does not prevent work from being requeued. Thus
in theory new work can be queued after cancel_old_flush() from
reiserfs_freeze() has run. This will become larger problem once
flush_old_commits() can requeue the work itself.
Fix the problem by recording in sbi->work_queue that flushing work is
canceled and should not be requeued.
Signed-off-by: Jan Kara <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/reiserfs/journal.c | 2 +-
fs/reiserfs/reiserfs.h | 1 +
fs/reiserfs/super.c | 21 +++++++++++++++------
3 files changed, 17 insertions(+), 7 deletions(-)
diff --git a/fs/reiserfs/journal.c b/fs/reiserfs/journal.c
index d571e173a990..e503effd284d 100644
--- a/fs/reiserfs/journal.c
+++ b/fs/reiserfs/journal.c
@@ -1961,7 +1961,7 @@ static int do_journal_release(struct reiserfs_transaction_handle *th,
* will be requeued because superblock is being shutdown and doesn't
* have MS_ACTIVE set.
*/
- cancel_delayed_work_sync(&REISERFS_SB(sb)->old_work);
+ reiserfs_cancel_old_flush(sb);
/* wait for all commits to finish */
cancel_delayed_work_sync(&SB_JOURNAL(sb)->j_work);
diff --git a/fs/reiserfs/reiserfs.h b/fs/reiserfs/reiserfs.h
index 1894d96ccb7c..8fb8107710f7 100644
--- a/fs/reiserfs/reiserfs.h
+++ b/fs/reiserfs/reiserfs.h
@@ -2946,6 +2946,7 @@ int reiserfs_allocate_list_bitmaps(struct super_block *s,
struct reiserfs_list_bitmap *, unsigned int);
void reiserfs_schedule_old_flush(struct super_block *s);
+void reiserfs_cancel_old_flush(struct super_block *s);
void add_save_link(struct reiserfs_transaction_handle *th,
struct inode *inode, int truncate);
int remove_save_link(struct inode *inode, int truncate);
diff --git a/fs/reiserfs/super.c b/fs/reiserfs/super.c
index b27ef3541490..5b8acce4f863 100644
--- a/fs/reiserfs/super.c
+++ b/fs/reiserfs/super.c
@@ -89,7 +89,9 @@ static void flush_old_commits(struct work_struct *work)
s = sbi->s_journal->j_work_sb;
spin_lock(&sbi->old_work_lock);
- sbi->work_queued = 0;
+ /* Avoid clobbering the cancel state... */
+ if (sbi->work_queued == 1)
+ sbi->work_queued = 0;
spin_unlock(&sbi->old_work_lock);
reiserfs_sync_fs(s, 1);
@@ -116,21 +118,22 @@ void reiserfs_schedule_old_flush(struct super_block *s)
spin_unlock(&sbi->old_work_lock);
}
-static void cancel_old_flush(struct super_block *s)
+void reiserfs_cancel_old_flush(struct super_block *s)
{
struct reiserfs_sb_info *sbi = REISERFS_SB(s);
- cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
spin_lock(&sbi->old_work_lock);
- sbi->work_queued = 0;
+ /* Make sure no new flushes will be queued */
+ sbi->work_queued = 2;
spin_unlock(&sbi->old_work_lock);
+ cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
}
static int reiserfs_freeze(struct super_block *s)
{
struct reiserfs_transaction_handle th;
- cancel_old_flush(s);
+ reiserfs_cancel_old_flush(s);
reiserfs_write_lock(s);
if (!(s->s_flags & MS_RDONLY)) {
@@ -151,7 +154,13 @@ static int reiserfs_freeze(struct super_block *s)
static int reiserfs_unfreeze(struct super_block *s)
{
+ struct reiserfs_sb_info *sbi = REISERFS_SB(s);
+
reiserfs_allow_writes(s);
+ spin_lock(&sbi->old_work_lock);
+ /* Allow old_work to run again */
+ sbi->work_queued = 0;
+ spin_unlock(&sbi->old_work_lock);
return 0;
}
@@ -2164,7 +2173,7 @@ error_unlocked:
if (sbi->commit_wq)
destroy_workqueue(sbi->commit_wq);
- cancel_delayed_work_sync(&REISERFS_SB(s)->old_work);
+ reiserfs_cancel_old_flush(s);
reiserfs_free_bitmap_cache(s);
if (SB_BUFFER_WITH_SB(s))
--
2.14.1
From: Andrew Lunn <[email protected]>
[ Upstream commit d39004ab136ebb6949a7dda9d24376f3d6209295 ]
Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.
Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/faraday/ftgmac100.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index c77fa4a69844..0900fd5098eb 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -28,6 +28,7 @@
#include <linux/io.h>
#include <linux/module.h>
#include <linux/netdevice.h>
+#include <linux/of.h>
#include <linux/phy.h>
#include <linux/platform_device.h>
#include <net/ip.h>
--
2.14.1
From: Nate Watterson <[email protected]>
[ Upstream commit 5016bdb796b3726eec043ca0ce3be981f712c756 ]
Normally, calling alloc_iova() using an iova_domain with insufficient
pfns remaining between start_pfn and dma_limit will fail and return a
NULL pointer. Unexpectedly, if such a "full" iova_domain contains an
iova with pfn_lo == 0, the alloc_iova() call will instead succeed and
return an iova containing invalid pfns.
This is caused by an underflow bug in __alloc_and_insert_iova_range()
that occurs after walking the "full" iova tree when the search ends
at the iova with pfn_lo == 0 and limit_pfn is then adjusted to be just
below that (-1). This (now huge) limit_pfn gives the impression that a
vast amount of space is available between it and start_pfn and thus
a new iova is allocated with the invalid pfn_hi value, 0xFFF.... .
To rememdy this, a check is introduced to ensure that adjustments to
limit_pfn will not underflow.
This issue has been observed in the wild, and is easily reproduced with
the following sample code.
struct iova_domain *iovad = kzalloc(sizeof(*iovad), GFP_KERNEL);
struct iova *rsvd_iova, *good_iova, *bad_iova;
unsigned long limit_pfn = 3;
unsigned long start_pfn = 1;
unsigned long va_size = 2;
init_iova_domain(iovad, SZ_4K, start_pfn, limit_pfn);
rsvd_iova = reserve_iova(iovad, 0, 0);
good_iova = alloc_iova(iovad, va_size, limit_pfn, true);
bad_iova = alloc_iova(iovad, va_size, limit_pfn, true);
Prior to the patch, this yielded:
*rsvd_iova == {0, 0} /* Expected */
*good_iova == {2, 3} /* Expected */
*bad_iova == {-2, -1} /* Oh no... */
After the patch, bad_iova is NULL as expected since inadequate
space remains between limit_pfn and start_pfn after allocating
good_iova.
Signed-off-by: Nate Watterson <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/iommu/iova.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/iommu/iova.c b/drivers/iommu/iova.c
index f6b17e6af2fb..c9e54a0b4bd1 100644
--- a/drivers/iommu/iova.c
+++ b/drivers/iommu/iova.c
@@ -118,7 +118,7 @@ static int __alloc_and_insert_iova_range(struct iova_domain *iovad,
break; /* found a free slot */
}
adjust_limit_pfn:
- limit_pfn = curr_iova->pfn_lo - 1;
+ limit_pfn = curr_iova->pfn_lo ? (curr_iova->pfn_lo - 1) : 0;
move_left:
prev = curr;
curr = rb_prev(curr);
--
2.14.1
From: Prarit Bhargava <[email protected]>
[ Upstream commit fda78d7a0ead144f4b2cdb582dcba47911f4952c ]
The pci_bus_type .shutdown method, pci_device_shutdown(), is called from
device_shutdown() in the kernel restart and shutdown paths.
Previously, pci_device_shutdown() called pci_msi_shutdown() and
pci_msix_shutdown(). This disables MSI and MSI-X, which causes the device
to fall back to raising interrupts via INTx. But the driver is still bound
to the device, it doesn't know about this change, and it likely doesn't
have an INTx handler, so these INTx interrupts cause "nobody cared"
warnings like this:
irq 16: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.2-1.el7_UNSUPPORTED.x86_64 #1
Hardware name: Hewlett-Packard HP Z820 Workstation/158B, BIOS J63 v03.90 06/
...
The MSI disabling code was added by d52877c7b1af ("pci/irq: let
pci_device_shutdown to call pci_msi_shutdown v2") because a driver left MSI
enabled and kdump failed because the kexeced kernel wasn't prepared to
receive the MSI interrupts.
Subsequent commits 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even
if kernel doesn't support MSI") and e80e7edc55ba ("PCI/MSI: Initialize MSI
capability for all architectures") changed the kexeced kernel to disable
all MSIs itself so it no longer depends on the crashed kernel to clean up
after itself.
Stop disabling MSI/MSI-X in pci_device_shutdown(). This resolves the
"nobody cared" unhandled IRQ issue above. It also allows PCI serial
devices, which may rely on the MSI interrupts, to continue outputting
messages during reboot/shutdown.
[bhelgaas: changelog, drop pci_msi_shutdown() and pci_msix_shutdown() calls
altogether]
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=187351
Signed-off-by: Prarit Bhargava <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
CC: Alex Williamson <[email protected]>
CC: David Arcari <[email protected]>
CC: Myron Stowe <[email protected]>
CC: Lukas Wunner <[email protected]>
CC: Keith Busch <[email protected]>
CC: Mika Westerberg <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/pci/pci-driver.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 0ad37e69746d..b92480973586 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -450,8 +450,6 @@ static void pci_device_shutdown(struct device *dev)
if (drv && drv->shutdown)
drv->shutdown(pci_dev);
- pci_msi_shutdown(pci_dev);
- pci_msix_shutdown(pci_dev);
#ifdef CONFIG_KEXEC
/*
--
2.14.1
From: Roger Quadros <[email protected]>
[ Upstream commit e2d54fe76997301b49311bde7ba8ef52b47896f9 ]
It seems that if L3_INIT clkdomain is kept in HW_AUTO while usb_otg_ss
is in use then there are random chances that the usb_otg_ss module
will fail to completely idle. i.e. IDLEST = 0x2 instead of 0x3.
Preventing L3_INIT from HW_AUTO while usb_otg_ss module is in use
fixes this issue.
We don't know yet if usb_otg_ss instances 3 and 4 are affected by this
issue or not so don't add this flag for those instances.
Cc: Tero Kristo <[email protected]>
Signed-off-by: Roger Quadros <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
index 4e9d2a97c2cb..5c8da1a6feea 100644
--- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
@@ -2106,6 +2106,7 @@ static struct omap_hwmod dra7xx_usb_otg_ss1_hwmod = {
.class = &dra7xx_usb_otg_ss_hwmod_class,
.clkdm_name = "l3init_clkdm",
.main_clk = "dpll_core_h13x2_ck",
+ .flags = HWMOD_CLKDM_NOAUTO,
.prcm = {
.omap4 = {
.clkctrl_offs = DRA7XX_CM_L3INIT_USB_OTG_SS1_CLKCTRL_OFFSET,
@@ -2127,6 +2128,7 @@ static struct omap_hwmod dra7xx_usb_otg_ss2_hwmod = {
.class = &dra7xx_usb_otg_ss_hwmod_class,
.clkdm_name = "l3init_clkdm",
.main_clk = "dpll_core_h13x2_ck",
+ .flags = HWMOD_CLKDM_NOAUTO,
.prcm = {
.omap4 = {
.clkctrl_offs = DRA7XX_CM_L3INIT_USB_OTG_SS2_CLKCTRL_OFFSET,
--
2.14.1
From: Anton Blanchard <[email protected]>
[ Upstream commit a7a9dcd882a67b68568868b988289fce5ffd8419 ]
Early on in do_page_fault() we call store_updates_sp(), regardless of
the type of exception. For an instruction miss this doesn't make
sense, because we only use this information to detect if a data miss
is the result of a stack expansion instruction or not.
Worse still, it results in a data miss within every userspace
instruction miss handler, because we try and load the very instruction
we are about to install a pte for!
A simple exec microbenchmark runs 6% faster on POWER8 with this fix:
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
unsigned long left = atol(argv[1]);
char leftstr[16];
if (left-- == 0)
return 0;
sprintf(leftstr, "%ld", left);
execlp(argv[0], argv[0], leftstr, NULL);
perror("exec failed\n");
return 0;
}
Pass the number of iterations on the command line (eg 10000) and time
how long it takes to execute.
Signed-off-by: Anton Blanchard <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/mm/fault.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c
index f06b56baf0b3..9b47840be82e 100644
--- a/arch/powerpc/mm/fault.c
+++ b/arch/powerpc/mm/fault.c
@@ -294,7 +294,7 @@ int __kprobes do_page_fault(struct pt_regs *regs, unsigned long address,
* can result in fault, which will cause a deadlock when called with
* mmap_sem held
*/
- if (user_mode(regs))
+ if (!is_exec && user_mode(regs))
store_update_sp = store_updates_sp(regs);
if (user_mode(regs))
--
2.14.1
From: Geert Uytterhoeven <[email protected]>
[ Upstream commit d13d4e063d4a08eb1686e890e9183dde709871bf ]
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: bcde372254386872 ("ARM: shmobile: r8a7790: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/r8a7790.dtsi | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index e20affe156c1..2a4e54732419 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -978,8 +978,11 @@
compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150998 0 4>, <0 0xe61509a8 0 4>;
clocks = <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
- <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+ <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI_ALL>,
<&p_clk>,
<&mstp10_clks R8A7790_CLK_SCU_ALL>, <&mstp10_clks R8A7790_CLK_SCU_ALL>,
<&mstp10_clks R8A7790_CLK_SCU_ALL>, <&mstp10_clks R8A7790_CLK_SCU_ALL>,
--
2.14.1
From: Samuel Thibault <[email protected]>
[ Upstream commit 2ed2b8621be2708c0f6d61fe9841e9ad8b9753f0 ]
commit bbeddf52adc1 ("printk: move braille console support into
separate braille.[ch] files") introduced _braille_console_setup()
to outline the braille initialization code. There was however some
confusion over the value it was supposed to return. commit 2cfe6c4ac7ee
("printk: Fix return of braille_register_console()") tried to fix it
but failed to.
This fixes and documents the returned value according to the use
in printk.c: non-zero return means a parsing error, and thus this
console configuration should be ignored.
Signed-off-by: Samuel Thibault <[email protected]>
Cc: Aleksey Makarov <[email protected]>
Cc: Joe Perches <[email protected]>
Cc: Ming Lei <[email protected]>
Cc: Steven Rostedt <[email protected]>
Acked-by: Petr Mladek <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/printk/braille.c | 15 ++++++++-------
kernel/printk/braille.h | 13 ++++++++++---
2 files changed, 18 insertions(+), 10 deletions(-)
diff --git a/kernel/printk/braille.c b/kernel/printk/braille.c
index 276762f3a460..e035876af5e2 100644
--- a/kernel/printk/braille.c
+++ b/kernel/printk/braille.c
@@ -2,12 +2,13 @@
#include <linux/kernel.h>
#include <linux/console.h>
+#include <linux/errno.h>
#include <linux/string.h>
#include "console_cmdline.h"
#include "braille.h"
-char *_braille_console_setup(char **str, char **brl_options)
+int _braille_console_setup(char **str, char **brl_options)
{
if (!memcmp(*str, "brl,", 4)) {
*brl_options = "";
@@ -15,14 +16,14 @@ char *_braille_console_setup(char **str, char **brl_options)
} else if (!memcmp(str, "brl=", 4)) {
*brl_options = *str + 4;
*str = strchr(*brl_options, ',');
- if (!*str)
+ if (!*str) {
pr_err("need port name after brl=\n");
- else
- *((*str)++) = 0;
- } else
- return NULL;
+ return -EINVAL;
+ }
+ *((*str)++) = 0;
+ }
- return *str;
+ return 0;
}
int
diff --git a/kernel/printk/braille.h b/kernel/printk/braille.h
index 769d771145c8..749a6756843a 100644
--- a/kernel/printk/braille.h
+++ b/kernel/printk/braille.h
@@ -9,7 +9,14 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
c->brl_options = brl_options;
}
-char *
+/*
+ * Setup console according to braille options.
+ * Return -EINVAL on syntax error, 0 on success (or no braille option was
+ * actually given).
+ * Modifies str to point to the serial options
+ * Sets brl_options to the parsed braille options.
+ */
+int
_braille_console_setup(char **str, char **brl_options);
int
@@ -25,10 +32,10 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
{
}
-static inline char *
+static inline int
_braille_console_setup(char **str, char **brl_options)
{
- return NULL;
+ return 0;
}
static inline int
--
2.14.1
From: "Kirill A. Shutemov" <[email protected]>
[ Upstream commit 591a3d7c09fa08baff48ad86c2347dbd28a52753 ]
0day testing by Fengguang Wu triggered this crash while running Trinity:
kernel BUG at include/linux/pagemap.h:151!
...
CPU: 0 PID: 458 Comm: trinity-c0 Not tainted 4.11.0-rc2-00251-g2947ba0 #1
...
Call Trace:
__get_user_pages_fast()
get_user_pages_fast()
get_futex_key()
futex_requeue()
do_futex()
SyS_futex()
do_syscall_64()
entry_SYSCALL64_slow_path()
It' VM_BUG_ON() due to false-negative in_atomic(). We call
page_cache_get_speculative() with disabled local interrupts.
It should be atomic enough.
So let's check for disabled interrupts in the VM_BUG_ON() condition
too, to resolve this.
( This got triggered by the conversion of the x86 GUP code to the
generic GUP code. )
Reported-by: Fengguang Wu <[email protected]>
Signed-off-by: Kirill A. Shutemov <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: LKP <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/pagemap.h | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/include/linux/pagemap.h b/include/linux/pagemap.h
index 30a8f531236c..2629fc3e24e0 100644
--- a/include/linux/pagemap.h
+++ b/include/linux/pagemap.h
@@ -146,7 +146,7 @@ static inline int page_cache_get_speculative(struct page *page)
#ifdef CONFIG_TINY_RCU
# ifdef CONFIG_PREEMPT_COUNT
- VM_BUG_ON(!in_atomic());
+ VM_BUG_ON(!in_atomic() && !irqs_disabled());
# endif
/*
* Preempt must be disabled here - we rely on rcu_read_lock doing
@@ -184,7 +184,7 @@ static inline int page_cache_add_speculative(struct page *page, int count)
#if !defined(CONFIG_SMP) && defined(CONFIG_TREE_RCU)
# ifdef CONFIG_PREEMPT_COUNT
- VM_BUG_ON(!in_atomic());
+ VM_BUG_ON(!in_atomic() && !irqs_disabled());
# endif
VM_BUG_ON_PAGE(page_count(page) == 0, page);
atomic_add(count, &page->_count);
--
2.14.1
From: Akinobu Mita <[email protected]>
[ Upstream commit 812613591cb652344186c4cd912304ed02138566 ]
When running the spi-loopback-test with slower clock rate like 10 KHz,
the test for 251 bytes transfer was failed. This failure triggered an
spi-omap2-mcspi's error message "DMA RX last word empty".
This message means that PIO for reading the remaining bytes due to the
DMA transfer length reduction is failed. This problem can be fixed by
polling OMAP2_MCSPI_CHSTAT_RXS bit in channel status register to wait
until the receive buffer register is filled.
Cc: Mark Brown <[email protected]>
Signed-off-by: Akinobu Mita <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/spi/spi-omap2-mcspi.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 352eed7463ac..7f48cb57822c 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -441,6 +441,8 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
int elements = 0;
int word_len, element_count;
struct omap2_mcspi_cs *cs = spi->controller_state;
+ void __iomem *chstat_reg = cs->base + OMAP2_MCSPI_CHSTAT0;
+
mcspi = spi_master_get_devdata(spi->master);
mcspi_dma = &mcspi->dma_channels[spi->chip_select];
count = xfer->len;
@@ -501,8 +503,8 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
if (l & OMAP2_MCSPI_CHCONF_TURBO) {
elements--;
- if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0)
- & OMAP2_MCSPI_CHSTAT_RXS)) {
+ if (!mcspi_wait_for_reg_bit(chstat_reg,
+ OMAP2_MCSPI_CHSTAT_RXS)) {
u32 w;
w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0);
@@ -520,8 +522,7 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
return count;
}
}
- if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0)
- & OMAP2_MCSPI_CHSTAT_RXS)) {
+ if (!mcspi_wait_for_reg_bit(chstat_reg, OMAP2_MCSPI_CHSTAT_RXS)) {
u32 w;
w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0);
--
2.14.1
From: Gao Feng <[email protected]>
[ Upstream commit c48367427a39ea0b85c7cf018fe4256627abfd9e ]
Because sysctl_tcp_adv_win_scale could be changed any time, so there
is one race in tcp_win_from_space.
For example,
1.sysctl_tcp_adv_win_scale<=0 (sysctl_tcp_adv_win_scale is negative now)
2.space>>(-sysctl_tcp_adv_win_scale) (sysctl_tcp_adv_win_scale is postive now)
As a result, tcp_win_from_space returns 0. It is unexpected.
Certainly if the compiler put the sysctl_tcp_adv_win_scale into one
register firstly, then use the register directly, it would be ok.
But we could not depend on the compiler behavior.
Signed-off-by: Gao Feng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/net/tcp.h | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/include/net/tcp.h b/include/net/tcp.h
index 2cd7003a8a19..15564a2cc28c 100644
--- a/include/net/tcp.h
+++ b/include/net/tcp.h
@@ -1099,9 +1099,11 @@ void tcp_select_initial_window(int __space, __u32 mss, __u32 *rcv_wnd,
static inline int tcp_win_from_space(int space)
{
- return sysctl_tcp_adv_win_scale<=0 ?
- (space>>(-sysctl_tcp_adv_win_scale)) :
- space - (space>>sysctl_tcp_adv_win_scale);
+ int tcp_adv_win_scale = sysctl_tcp_adv_win_scale;
+
+ return tcp_adv_win_scale <= 0 ?
+ (space>>(-tcp_adv_win_scale)) :
+ space - (space>>tcp_adv_win_scale);
}
/* Note: caller must be prepared to deal with negative returns */
--
2.14.1
From: Pan Xinhui <[email protected]>
[ Upstream commit 3b5bf42b81d56085fd58692b5117f69aa77fdff7 ]
Once xmon is triggered by sysrq-x, it is enabled always afterwards even
if it is disabled during boot. This will cause a system reset interrupt
fail to dump. So keep xmon in its original state after exit.
We have several ways to set xmon on or off.
1) by a build config CONFIG_XMON_DEFAULT.
2) by a boot cmdline with xmon or xmon=early or xmon=on to enable xmon
and xmon=off to disable xmon. This value will override that in step 1.
3) by a debugfs interface, as proposed in this patchset.
And this value can override those in step 1 and 2.
Signed-off-by: Pan Xinhui <[email protected]>
Signed-off-by: Guilherme G. Piccoli <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/powerpc/xmon/xmon.c | 17 ++++++++++-------
1 file changed, 10 insertions(+), 7 deletions(-)
diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index e23f559faa47..7d5464524324 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -64,6 +64,7 @@ static int xmon_gate;
#endif /* CONFIG_SMP */
static unsigned long in_xmon __read_mostly = 0;
+static int xmon_on = IS_ENABLED(CONFIG_XMON_DEFAULT);
static unsigned long adrs;
static int size = 1;
@@ -2938,6 +2939,8 @@ static void sysrq_handle_xmon(int key)
/* ensure xmon is enabled */
xmon_init(1);
debugger(get_irq_regs());
+ if (!xmon_on)
+ xmon_init(0);
}
static struct sysrq_key_op sysrq_xmon_op = {
@@ -2954,7 +2957,7 @@ static int __init setup_xmon_sysrq(void)
__initcall(setup_xmon_sysrq);
#endif /* CONFIG_MAGIC_SYSRQ */
-static int __initdata xmon_early, xmon_off;
+static int __initdata xmon_early;
static int __init early_parse_xmon(char *p)
{
@@ -2962,10 +2965,12 @@ static int __init early_parse_xmon(char *p)
/* just "xmon" is equivalent to "xmon=early" */
xmon_init(1);
xmon_early = 1;
- } else if (strncmp(p, "on", 2) == 0)
+ xmon_on = 1;
+ } else if (strncmp(p, "on", 2) == 0) {
xmon_init(1);
- else if (strncmp(p, "off", 3) == 0)
- xmon_off = 1;
+ xmon_on = 1;
+ } else if (strncmp(p, "off", 3) == 0)
+ xmon_on = 0;
else if (strncmp(p, "nobt", 4) == 0)
xmon_no_auto_backtrace = 1;
else
@@ -2977,10 +2982,8 @@ early_param("xmon", early_parse_xmon);
void __init xmon_setup(void)
{
-#ifdef CONFIG_XMON_DEFAULT
- if (!xmon_off)
+ if (xmon_on)
xmon_init(1);
-#endif
if (xmon_early)
debugger(NULL);
}
--
2.14.1
From: Davide Caratti <[email protected]>
[ Upstream commit add641e7dee31b36aee83412c29e39dd1f5e0c9c ]
after act_csum computes the checksum on skbs carrying GSO TCP/UDP packets,
subsequent segmentation fails because skb_needs_check(skb, true) returns
true. Because of that, skb_warn_bad_offload() is invoked and the following
message is displayed:
WARNING: CPU: 3 PID: 28 at net/core/dev.c:2553 skb_warn_bad_offload+0xf0/0xfd
<...>
[<ffffffff8171f486>] skb_warn_bad_offload+0xf0/0xfd
[<ffffffff8161304c>] __skb_gso_segment+0xec/0x110
[<ffffffff8161340d>] validate_xmit_skb+0x12d/0x2b0
[<ffffffff816135d2>] validate_xmit_skb_list+0x42/0x70
[<ffffffff8163c560>] sch_direct_xmit+0xd0/0x1b0
[<ffffffff8163c760>] __qdisc_run+0x120/0x270
[<ffffffff81613b3d>] __dev_queue_xmit+0x23d/0x690
[<ffffffff81613fa0>] dev_queue_xmit+0x10/0x20
Since GSO is able to compute checksum on individual segments of such skbs,
we can simply skip mangling the packet.
Signed-off-by: Davide Caratti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
net/sched/act_csum.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/net/sched/act_csum.c b/net/sched/act_csum.c
index edbf40dac709..72ff5d21f4a7 100644
--- a/net/sched/act_csum.c
+++ b/net/sched/act_csum.c
@@ -176,6 +176,9 @@ static int tcf_csum_ipv4_tcp(struct sk_buff *skb,
struct tcphdr *tcph;
const struct iphdr *iph;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4)
+ return 1;
+
tcph = tcf_csum_skb_nextlayer(skb, ihl, ipl, sizeof(*tcph));
if (tcph == NULL)
return 0;
@@ -197,6 +200,9 @@ static int tcf_csum_ipv6_tcp(struct sk_buff *skb,
struct tcphdr *tcph;
const struct ipv6hdr *ip6h;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6)
+ return 1;
+
tcph = tcf_csum_skb_nextlayer(skb, ihl, ipl, sizeof(*tcph));
if (tcph == NULL)
return 0;
@@ -220,6 +226,9 @@ static int tcf_csum_ipv4_udp(struct sk_buff *skb,
const struct iphdr *iph;
u16 ul;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_UDP)
+ return 1;
+
/*
* Support both UDP and UDPLITE checksum algorithms, Don't use
* udph->len to get the real length without any protocol check,
@@ -273,6 +282,9 @@ static int tcf_csum_ipv6_udp(struct sk_buff *skb,
const struct ipv6hdr *ip6h;
u16 ul;
+ if (skb_is_gso(skb) && skb_shinfo(skb)->gso_type & SKB_GSO_UDP)
+ return 1;
+
/*
* Support both UDP and UDPLITE checksum algorithms, Don't use
* udph->len to get the real length without any protocol check,
--
2.14.1
From: Janusz Krzysztofik <[email protected]>
[ Upstream commit 54449af0e0b2ea43a8166611c95b730c850c3184 ]
After changes to v4l2_clk API introduced in v4.1 by commits a37462b919
'[media] V4L: remove clock name from v4l2_clk API' and 4f528afcfb
'[media] V4L: add CCF support to the v4l2_clk API', ov6650 sensor
stopped responding because v4l2_clk_get(), still called with
depreciated V4L2 clock name "mclk", started to return respective CCF
clock instead of the V4l2 one registered by soc_camera. Fix it by
calling v4l2_clk_get() with NULL clock name.
Created and tested on Amstrad Delta against Linux-4.7-rc3 with
omap1_camera fixes.
Signed-off-by: Janusz Krzysztofik <[email protected]>
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/media/i2c/soc_camera/ov6650.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/media/i2c/soc_camera/ov6650.c b/drivers/media/i2c/soc_camera/ov6650.c
index ab01598ec83f..d8be90cd6e56 100644
--- a/drivers/media/i2c/soc_camera/ov6650.c
+++ b/drivers/media/i2c/soc_camera/ov6650.c
@@ -1016,7 +1016,7 @@ static int ov6650_probe(struct i2c_client *client,
priv->code = V4L2_MBUS_FMT_YUYV8_2X8;
priv->colorspace = V4L2_COLORSPACE_JPEG;
- priv->clk = v4l2_clk_get(&client->dev, "mclk");
+ priv->clk = v4l2_clk_get(&client->dev, NULL);
if (IS_ERR(priv->clk)) {
ret = PTR_ERR(priv->clk);
goto eclkget;
--
2.14.1
From: David Engraf <[email protected]>
[ Upstream commit 1b8955bc5ac575009835e371ae55e7f3af2197a9 ]
The scheduler clock framework may not use the correct timeout for the clock
wrap. This happens when a new clock driver calls sched_clock_register()
after the kernel called sched_clock_postinit(). In this case the clock wrap
timeout is too long thus sched_clock_poll() is called too late and the clock
already wrapped.
On my ARM system the scheduler was no longer scheduling any other task than
the idle task because the sched_clock() wrapped.
Signed-off-by: David Engraf <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
kernel/time/sched_clock.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/kernel/time/sched_clock.c b/kernel/time/sched_clock.c
index 01d2d15aa662..830e214f372c 100644
--- a/kernel/time/sched_clock.c
+++ b/kernel/time/sched_clock.c
@@ -146,6 +146,11 @@ void __init sched_clock_register(u64 (*read)(void), int bits,
cd.epoch_ns = ns;
raw_write_seqcount_end(&cd.seq);
+ if (sched_clock_timer.function != NULL) {
+ /* update timeout for clock wrap */
+ hrtimer_start(&sched_clock_timer, cd.wrap_kt, HRTIMER_MODE_REL);
+ }
+
r = rate;
if (r >= 4000000) {
r /= 1000000;
--
2.14.1
From: Rob Herring <[email protected]>
[ Upstream commit bcf54d5385abaea9c8026aae6f4eeb348671a52d ]
If the length of the modalias is greater than the buffer size, then the
modalias is truncated. However the untruncated length is returned which
will cause an error. Fix this to return the truncated length. If an error
in the case was desired, then then we should just return -ENOMEM.
The reality is no device will ever have 4KB of compatible strings to hit
this case.
Signed-off-by: Rob Herring <[email protected]>
Cc: Frank Rowand <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/of/device.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/of/device.c b/drivers/of/device.c
index de20165bad48..2ef5ca45a136 100644
--- a/drivers/of/device.c
+++ b/drivers/of/device.c
@@ -126,7 +126,7 @@ ssize_t of_device_get_modalias(struct device *dev, char *str, ssize_t len)
str[i] = '_';
}
- return tsize;
+ return repend;
}
EXPORT_SYMBOL_GPL(of_device_get_modalias);
--
2.14.1
From: Linus Walleij <[email protected]>
[ Upstream commit c2a736b698008d296c5010ec39077eeb5796109f ]
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <[email protected]>
Signed-off-by: Jonas Jensen <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
arch/arm/boot/dts/moxart-uc7112lx.dts | 2 +-
arch/arm/boot/dts/moxart.dtsi | 17 +++++++++--------
2 files changed, 10 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
index 10d088df0c35..4a962a26482d 100644
--- a/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -6,7 +6,7 @@
*/
/dts-v1/;
-/include/ "moxart.dtsi"
+#include "moxart.dtsi"
/ {
model = "MOXA UC-7112-LX";
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
index 1fd27ed65a01..64f2f44235d0 100644
--- a/arch/arm/boot/dts/moxart.dtsi
+++ b/arch/arm/boot/dts/moxart.dtsi
@@ -6,6 +6,7 @@
*/
/include/ "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
compatible = "moxa,moxart";
@@ -36,8 +37,8 @@
ranges;
intc: interrupt-controller@98800000 {
- compatible = "moxa,moxart-ic";
- reg = <0x98800000 0x38>;
+ compatible = "moxa,moxart-ic", "faraday,ftintc010";
+ reg = <0x98800000 0x100>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-mask = <0x00080000>;
@@ -59,7 +60,7 @@
timer: timer@98400000 {
compatible = "moxa,moxart-timer";
reg = <0x98400000 0x42>;
- interrupts = <19 1>;
+ interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
clocks = <&clk_apb>;
};
@@ -80,7 +81,7 @@
dma: dma@90500000 {
compatible = "moxa,moxart-dma";
reg = <0x90500080 0x40>;
- interrupts = <24 0>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
};
@@ -93,7 +94,7 @@
sdhci: sdhci@98e00000 {
compatible = "moxa,moxart-sdhci";
reg = <0x98e00000 0x5C>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clk_apb>;
dmas = <&dma 5>,
<&dma 5>;
@@ -120,7 +121,7 @@
mac0: mac@90900000 {
compatible = "moxa,moxart-mac";
reg = <0x90900000 0x90>;
- interrupts = <25 0>;
+ interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
phy-handle = <ðphy0>;
phy-mode = "mii";
status = "disabled";
@@ -129,7 +130,7 @@
mac1: mac@92000000 {
compatible = "moxa,moxart-mac";
reg = <0x92000000 0x90>;
- interrupts = <27 0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
phy-handle = <ðphy1>;
phy-mode = "mii";
status = "disabled";
@@ -138,7 +139,7 @@
uart0: uart@98200000 {
compatible = "ns16550a";
reg = <0x98200000 0x20>;
- interrupts = <31 8>;
+ interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <14745600>;
--
2.14.1
From: Tomasz Kramkowski <[email protected]>
[ Upstream commit c3883fe06488a483658ba5d849b70e49bee15e7c ]
This patch fixes an issue in drivers/hid/hid-input.c where values
outside of the logical range are not clamped when "null state" bit of
the input control is not set.
This was discussed on the lists [1] and this change stems from the fact
due to the ambiguity of the HID specification it might be appropriate to
follow Microsoft's own interpretation of the specification. As noted in
Microsoft's documentation [2] in the section titled "Required HID usages
for digitizers" it is noted that values reported outside the logical
range "will be considered as invalid data and the value will be changed
to the nearest boundary value (logical min/max)."
This patch fixes an issue where the (1292:4745) Innomedia INNEX
GENESIS/ATARI reports out of range values for its X and Y axis of the
DPad which, due to the null state bit being unset, are forwarded to
userspace as is. Now these values will get clamped to the logical range
before being forwarded to userspace. This device was also used to test
this patch.
This patch expands on commit 3f3752705dbd ("HID: reject input outside
logical range only if null state is set").
[1]: http://lkml.kernel.org/r/[email protected]
[2]: https://msdn.microsoft.com/en-us/library/windows/hardware/dn672278(v=vs.85).asp
Signed-off-by: Tomasz Kramkowski <[email protected]>
Acked-by: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-input.c | 21 ++++++++++++++-------
1 file changed, 14 insertions(+), 7 deletions(-)
diff --git a/drivers/hid/hid-input.c b/drivers/hid/hid-input.c
index 6d766fe2c7f4..bb870ee75a90 100644
--- a/drivers/hid/hid-input.c
+++ b/drivers/hid/hid-input.c
@@ -1090,19 +1090,26 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
/*
* Ignore out-of-range values as per HID specification,
- * section 5.10 and 6.2.25.
+ * section 5.10 and 6.2.25, when NULL state bit is present.
+ * When it's not, clamp the value to match Microsoft's input
+ * driver as mentioned in "Required HID usages for digitizers":
+ * https://msdn.microsoft.com/en-us/library/windows/hardware/dn672278(v=vs.85).asp
*
* The logical_minimum < logical_maximum check is done so that we
* don't unintentionally discard values sent by devices which
* don't specify logical min and max.
*/
if ((field->flags & HID_MAIN_ITEM_VARIABLE) &&
- (field->flags & HID_MAIN_ITEM_NULL_STATE) &&
- (field->logical_minimum < field->logical_maximum) &&
- (value < field->logical_minimum ||
- value > field->logical_maximum)) {
- dbg_hid("Ignoring out-of-range value %x\n", value);
- return;
+ (field->logical_minimum < field->logical_maximum)) {
+ if (field->flags & HID_MAIN_ITEM_NULL_STATE &&
+ (value < field->logical_minimum ||
+ value > field->logical_maximum)) {
+ dbg_hid("Ignoring out-of-range value %x\n", value);
+ return;
+ }
+ value = clamp(value,
+ field->logical_minimum,
+ field->logical_maximum);
}
/*
--
2.14.1
From: Brian King <[email protected]>
[ Upstream commit 66a0d59cdd12546ddf01d229de28b07ccf6d637f ]
Following a command abort or device reset, ipr's EH handlers wait for
the commands getting aborted to get sent back from the adapter prior to
returning from the EH handler. This fixes up some cases where the
completion handler was not getting called, which would have resulted in
the EH thread waiting until it timed out, greatly extending EH time.
Signed-off-by: Brian King <[email protected]>
Reviewed-by: Wendy Xiong <[email protected]>
Tested-by: Wendy Xiong <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/scsi/ipr.c | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/ipr.c b/drivers/scsi/ipr.c
index 105adb4cf6a8..54dfae5c8ee3 100644
--- a/drivers/scsi/ipr.c
+++ b/drivers/scsi/ipr.c
@@ -828,8 +828,10 @@ static void ipr_sata_eh_done(struct ipr_cmnd *ipr_cmd)
qc->err_mask |= AC_ERR_OTHER;
sata_port->ioasa.status |= ATA_BUSY;
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
ata_qc_complete(qc);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -5830,8 +5832,10 @@ static void ipr_erp_done(struct ipr_cmnd *ipr_cmd)
res->in_erp = 0;
}
scsi_dma_unmap(ipr_cmd->scsi_cmd);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -6214,8 +6218,10 @@ static void ipr_erp_start(struct ipr_ioa_cfg *ioa_cfg,
}
scsi_dma_unmap(ipr_cmd->scsi_cmd);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
}
/**
@@ -6241,8 +6247,10 @@ static void ipr_scsi_done(struct ipr_cmnd *ipr_cmd)
scsi_dma_unmap(scsi_cmd);
spin_lock_irqsave(ipr_cmd->hrrq->lock, lock_flags);
- list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
scsi_cmd->scsi_done(scsi_cmd);
+ if (ipr_cmd->eh_comp)
+ complete(ipr_cmd->eh_comp);
+ list_add_tail(&ipr_cmd->queue, &ipr_cmd->hrrq->hrrq_free_q);
spin_unlock_irqrestore(ipr_cmd->hrrq->lock, lock_flags);
} else {
spin_lock_irqsave(ioa_cfg->host->host_lock, lock_flags);
--
2.14.1
From: Mohammed Shafi Shajakhan <[email protected]>
[ Upstream commit ca07baab0b1e627ae1d4a55d190fb1c9d32a3445 ]
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/wireless/ath/ath10k/debug.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index 3756feba3223..d3ebac0d7f7a 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -1079,6 +1079,15 @@ static ssize_t ath10k_write_simulate_radar(struct file *file,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
+ struct ath10k_vif *arvif;
+
+ /* Just check for for the first vif alone, as all the vifs will be
+ * sharing the same channel and if the channel is disabled, all the
+ * vifs will share the same 'is_started' state.
+ */
+ arvif = list_first_entry(&ar->arvifs, typeof(*arvif), list);
+ if (!arvif->is_started)
+ return -EINVAL;
ieee80211_radar_detected(ar->hw);
--
2.14.1
From: Quan Nguyen <[email protected]>
[ Upstream commit e026e700d940a1ea3d3bc84d92ac668b1f015462 ]
This patch fixes the hardware checksum settings by properly program
the classifier. Otherwise, packet may be received with checksum error
on X-Gene1 SoC.
Signed-off-by: Quan Nguyen <[email protected]>
Signed-off-by: Iyappan Subramanian <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 1 +
drivers/net/ethernet/apm/xgene/xgene_enet_hw.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
index 7ba83ffb08ac..570e5284ff5f 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.c
@@ -535,6 +535,7 @@ static void xgene_enet_cle_bypass(struct xgene_enet_pdata *pdata,
xgene_enet_rd_csr(pdata, CLE_BYPASS_REG0_0_ADDR, &cb);
cb |= CFG_CLE_BYPASS_EN0;
CFG_CLE_IP_PROTOCOL0_SET(&cb, 3);
+ CFG_CLE_IP_HDR_LEN_SET(&cb, 0);
xgene_enet_wr_csr(pdata, CLE_BYPASS_REG0_0_ADDR, cb);
xgene_enet_rd_csr(pdata, CLE_BYPASS_REG1_0_ADDR, &cb);
diff --git a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
index ec45f3256f0e..66c3d0cd506f 100644
--- a/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
+++ b/drivers/net/ethernet/apm/xgene/xgene_enet_hw.h
@@ -143,6 +143,7 @@ enum xgene_enet_rm {
#define CFG_TXCLK_MUXSEL0_SET(dst, val) xgene_set_bits(dst, val, 29, 3)
#define CFG_CLE_IP_PROTOCOL0_SET(dst, val) xgene_set_bits(dst, val, 16, 2)
+#define CFG_CLE_IP_HDR_LEN_SET(dst, val) xgene_set_bits(dst, val, 8, 5)
#define CFG_CLE_DSTQID0_SET(dst, val) xgene_set_bits(dst, val, 0, 12)
#define CFG_CLE_FPSEL0_SET(dst, val) xgene_set_bits(dst, val, 16, 4)
#define CFG_MACMODE_SET(dst, val) xgene_set_bits(dst, val, 18, 2)
--
2.14.1
From: Alexander Potapenko <[email protected]>
[ Upstream commit e2f586bd83177d22072b275edd4b8b872daba924 ]
KMSAN (KernelMemorySanitizer, a new error detection tool) reports use of
uninitialized memory in selinux_socket_bind():
==================================================================
BUG: KMSAN: use of unitialized memory
inter: 0
CPU: 3 PID: 1074 Comm: packet2 Tainted: G B 4.8.0-rc6+ #1916
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000000 ffff8800882ffb08 ffffffff825759c8 ffff8800882ffa48
ffffffff818bf551 ffffffff85bab870 0000000000000092 ffffffff85bab550
0000000000000000 0000000000000092 00000000bb0009bb 0000000000000002
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff825759c8>] dump_stack+0x238/0x290 lib/dump_stack.c:51
[<ffffffff818bdee6>] kmsan_report+0x276/0x2e0 mm/kmsan/kmsan.c:1008
[<ffffffff818bf0fb>] __msan_warning+0x5b/0xb0 mm/kmsan/kmsan_instr.c:424
[<ffffffff822dae71>] selinux_socket_bind+0xf41/0x1080 security/selinux/hooks.c:4288
[<ffffffff8229357c>] security_socket_bind+0x1ec/0x240 security/security.c:1240
[<ffffffff84265d98>] SYSC_bind+0x358/0x5f0 net/socket.c:1366
[<ffffffff84265a22>] SyS_bind+0x82/0xa0 net/socket.c:1356
[<ffffffff81005678>] do_syscall_64+0x58/0x70 arch/x86/entry/common.c:292
[<ffffffff8518217c>] entry_SYSCALL64_slow_path+0x25/0x25 arch/x86/entry/entry_64.o:?
chained origin: 00000000ba6009bb
[<ffffffff810bb7a7>] save_stack_trace+0x27/0x50 arch/x86/kernel/stacktrace.c:67
[< inline >] kmsan_save_stack_with_flags mm/kmsan/kmsan.c:322
[< inline >] kmsan_save_stack mm/kmsan/kmsan.c:337
[<ffffffff818bd2b8>] kmsan_internal_chain_origin+0x118/0x1e0 mm/kmsan/kmsan.c:530
[<ffffffff818bf033>] __msan_set_alloca_origin4+0xc3/0x130 mm/kmsan/kmsan_instr.c:380
[<ffffffff84265b69>] SYSC_bind+0x129/0x5f0 net/socket.c:1356
[<ffffffff84265a22>] SyS_bind+0x82/0xa0 net/socket.c:1356
[<ffffffff81005678>] do_syscall_64+0x58/0x70 arch/x86/entry/common.c:292
[<ffffffff8518217c>] return_from_SYSCALL_64+0x0/0x6a arch/x86/entry/entry_64.o:?
origin description: ----address@SYSC_bind (origin=00000000b8c00900)
==================================================================
(the line numbers are relative to 4.8-rc6, but the bug persists upstream)
, when I run the following program as root:
=======================================================
#include <string.h>
#include <sys/socket.h>
#include <netinet/in.h>
int main(int argc, char *argv[]) {
struct sockaddr addr;
int size = 0;
if (argc > 1) {
size = atoi(argv[1]);
}
memset(&addr, 0, sizeof(addr));
int fd = socket(PF_INET6, SOCK_DGRAM, IPPROTO_IP);
bind(fd, &addr, size);
return 0;
}
=======================================================
(for different values of |size| other error reports are printed).
This happens because bind() unconditionally copies |size| bytes of
|addr| to the kernel, leaving the rest uninitialized. Then
security_socket_bind() reads the IP address bytes, including the
uninitialized ones, to determine the port, or e.g. pass them further to
sel_netnode_find(), which uses them to calculate a hash.
Signed-off-by: Alexander Potapenko <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
[PM: fixed some whitespace damage]
Signed-off-by: Paul Moore <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
security/selinux/hooks.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c
index 8223fe463fa3..98370d019e6c 100644
--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -4061,10 +4061,18 @@ static int selinux_socket_bind(struct socket *sock, struct sockaddr *address, in
u32 sid, node_perm;
if (family == PF_INET) {
+ if (addrlen < sizeof(struct sockaddr_in)) {
+ err = -EINVAL;
+ goto out;
+ }
addr4 = (struct sockaddr_in *)address;
snum = ntohs(addr4->sin_port);
addrp = (char *)&addr4->sin_addr.s_addr;
} else {
+ if (addrlen < SIN6_LEN_RFC2133) {
+ err = -EINVAL;
+ goto out;
+ }
addr6 = (struct sockaddr_in6 *)address;
snum = ntohs(addr6->sin6_port);
addrp = (char *)&addr6->sin6_addr.s6_addr;
--
2.14.1
From: Stephane Eranian <[email protected]>
[ Upstream commit 88b897a30c525c2eee6e7f16e1e8d0f18830845e ]
This patch significantly improves the execution time of
perf_event__synthesize_mmap_events() when running perf record on systems
where processes have lots of threads.
It just happens that cat /proc/pid/maps support uses a O(N^2) algorithm to
generate each map line in the maps file. If you have 1000 threads, then you
have necessarily 1000 stacks. For each vma, you need to check if it
corresponds to a thread's stack. With a large number of threads, this can take
a very long time. I have seen latencies >> 10mn.
As of today, perf does not use the fact that a mapping is a stack, therefore we
can work around the issue by using /proc/pid/tasks/pid/maps. This entry does
not try to map a vma to stack and is thus much faster with no loss of
functonality.
The proc-map-timeout logic is kept in case users still want some upper limit.
In V2, we fix the file path from /proc/pid/tasks/pid/maps to actual
/proc/pid/task/pid/maps, tasks -> task. Thanks Arnaldo for catching this.
Committer note:
This problem seems to have been elliminated in the kernel since commit :
b18cb64ead40 ("fs/proc: Stop trying to report thread stacks").
Signed-off-by: Stephane Eranian <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
tools/perf/util/event.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/tools/perf/util/event.c b/tools/perf/util/event.c
index da4c17cccb71..b9743621b2d0 100644
--- a/tools/perf/util/event.c
+++ b/tools/perf/util/event.c
@@ -167,8 +167,8 @@ int perf_event__synthesize_mmap_events(struct perf_tool *tool,
if (machine__is_default_guest(machine))
return 0;
- snprintf(filename, sizeof(filename), "%s/proc/%d/maps",
- machine->root_dir, pid);
+ snprintf(filename, sizeof(filename), "%s/proc/%d/task/%d/maps",
+ machine->root_dir, pid, pid);
fp = fopen(filename, "r");
if (fp == NULL) {
--
2.14.1
From: Thomas Petazzoni <[email protected]>
[ Upstream commit 2067e0a13cfe0b1bdca7b91bc5e4f2740b07d478 ]
On PPv2.2, the streaming mappings can be anywhere in the first 40 bits
of the physical address space. However, for the coherent mappings, we
still need them to be in the first 32 bits of the address space,
because all BM pools share a single register to store the high 32 bits
of the BM pool address, which means all BM pools must be allocated in
the same 4GB memory area.
Signed-off-by: Thomas Petazzoni <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index fdf3e382e464..68a5b71ec5c4 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -6339,6 +6339,20 @@ static int mvpp2_probe(struct platform_device *pdev)
/* Get system's tclk rate */
priv->tclk = clk_get_rate(priv->pp_clk);
+ if (priv->hw_version == MVPP22) {
+ err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(40));
+ if (err)
+ goto err_mg_clk;
+ /* Sadly, the BM pools all share the same register to
+ * store the high 32 bits of their address. So they
+ * must all have the same high 32 bits, which forces
+ * us to restrict coherent memory to DMA_BIT_MASK(32).
+ */
+ err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (err)
+ goto err_mg_clk;
+ }
+
/* Initialize network controller */
err = mvpp2_init(pdev, priv);
if (err < 0) {
--
2.14.1
From: Chris Wilson <[email protected]>
[ Upstream commit 608b20506941969ea30d8c08dc9ae02bb87dbf7d ]
On vblank instant-off systems, we can get into a situation where the cost
of enabling and disabling the vblank IRQ around a drmWaitVblank query
dominates. And with the advent of even deeper hardware sleep state,
touching registers becomes ever more expensive. However, we know that if
the user wants the current vblank counter, they are also very likely to
immediately queue a vblank wait and so we can keep the interrupt around
and only turn it off if we have no further vblank requests queued within
the interrupt interval.
After vblank event delivery, this patch adds a shadow of one vblank where
the interrupt is kept alive for the user to query and queue another vblank
event. Similarly, if the user is using blocking drmWaitVblanks, the
interrupt will be disabled on the IRQ following the wait completion.
However, if the user is simply querying the current vblank counter and
timestamp, the interrupt will be disabled after every IRQ and the user
will enabled it again on the first query following the IRQ.
v2: Mario Kleiner -
After testing this, one more thing that would make sense is to move
the disable block at the end of drm_handle_vblank() instead of at the
top.
Turns out that if high precision timestaming is disabled or doesn't
work for some reason (as can be simulated by echo 0 >
/sys/module/drm/parameters/timestamp_precision_usec), then with your
delayed disable code at its current place, the vblank counter won't
increment anymore at all for instant queries, ie. with your other
"instant query" patches. Clients which repeatedly query the counter
and wait for it to progress will simply hang, spinning in an endless
query loop. There's that comment in vblank_disable_and_save:
"* Skip this step if there isn't any high precision timestamp
* available. In that case we can't account for this and just
* hope for the best.
*/
With the disable happening after leading edge of vblank (== hw counter
increment already happened) but before the vblank counter/timestamp
handling in drm_handle_vblank, that step is needed to keep the counter
progressing, so skipping it is bad.
Now without high precision timestamping support, a kms driver must not
set dev->vblank_disable_immediate = true, as this would cause problems
for clients, so this shouldn't matter, but it would be good to still
make this robust against a future kms driver which might have
unreliable high precision timestamping, e.g., high precision
timestamping that intermittently doesn't work.
v3: Patch before coffee needs extra coffee.
Testcase: igt/kms_vblank
Signed-off-by: Chris Wilson <[email protected]>
Cc: Ville Syrjälä <[email protected]>
Cc: Daniel Vetter <[email protected]>
Cc: Michel Dänzer <[email protected]>
Cc: Laurent Pinchart <[email protected]>
Cc: Dave Airlie <[email protected]>,
Cc: Mario Kleiner <[email protected]>
Reviewed-by: Ville Syrjälä <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: http://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/gpu/drm/drm_irq.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/drm_irq.c b/drivers/gpu/drm/drm_irq.c
index 7d64d22486e9..4a3b13d883cc 100644
--- a/drivers/gpu/drm/drm_irq.c
+++ b/drivers/gpu/drm/drm_irq.c
@@ -1038,9 +1038,9 @@ void drm_vblank_put(struct drm_device *dev, int crtc)
if (atomic_dec_and_test(&vblank->refcount)) {
if (drm_vblank_offdelay == 0)
return;
- else if (dev->vblank_disable_immediate || drm_vblank_offdelay < 0)
+ else if (drm_vblank_offdelay < 0)
vblank_disable_fn((unsigned long)vblank);
- else
+ else if (!dev->vblank_disable_immediate)
mod_timer(&vblank->disable_timer,
jiffies + ((drm_vblank_offdelay * HZ)/1000));
}
@@ -1664,6 +1664,16 @@ bool drm_handle_vblank(struct drm_device *dev, int crtc)
wake_up(&vblank->queue);
drm_handle_vblank_events(dev, crtc);
+ /* With instant-off, we defer disabling the interrupt until after
+ * we finish processing the following vblank. The disable has to
+ * be last (after drm_handle_vblank_events) so that the timestamp
+ * is always accurate.
+ */
+ if (dev->vblank_disable_immediate &&
+ drm_vblank_offdelay > 0 &&
+ !atomic_read(&vblank->refcount))
+ vblank_disable_fn((unsigned long)vblank);
+
spin_unlock_irqrestore(&dev->event_lock, irqflags);
return true;
--
2.14.1
From: Valtteri Heikkilä <[email protected]>
[ Upstream commit 3f3752705dbd50b66b66ad7b4d54fe33d2f746ed ]
This patch fixes an issue in drivers/hid/hid-input.c where USB HID
control null state flag is not checked upon rejecting inputs outside
logical minimum-maximum range. The check should be made according to USB
HID specification 1.11, section 6.2.2.5, p.31. The fix will resolve
issues with some game controllers, such as:
https://bugzilla.kernel.org/show_bug.cgi?id=68621
[[email protected]: shortened and fixed spelling in commit message]
Signed-off-by: Valtteri Heikkilä <[email protected]>
Signed-off-by: Tomasz Kramkowski <[email protected]>
Acked-By: Benjamin Tissoires <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
drivers/hid/hid-input.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/hid/hid-input.c b/drivers/hid/hid-input.c
index 53d325968e42..6d766fe2c7f4 100644
--- a/drivers/hid/hid-input.c
+++ b/drivers/hid/hid-input.c
@@ -1097,6 +1097,7 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
* don't specify logical min and max.
*/
if ((field->flags & HID_MAIN_ITEM_VARIABLE) &&
+ (field->flags & HID_MAIN_ITEM_NULL_STATE) &&
(field->logical_minimum < field->logical_maximum) &&
(value < field->logical_minimum ||
value > field->logical_maximum)) {
--
2.14.1
From: "Naveen N. Rao" <[email protected]>
[ Upstream commit 90ec5e89e393c76e19afc845d8f88a5dc8315919 ]
kretprobes can be registered by specifying an absolute address or by
specifying offset to a symbol. However, we need to ensure this falls at
function entry so as to be able to determine the return address.
Validate the same during kretprobe registration. By default, there
should not be any offset from a function entry, as determined through a
kallsyms_lookup(). Introduce arch_function_offset_within_entry() as a
way for architectures to override this.
Signed-off-by: Naveen N. Rao <[email protected]>
Acked-by: Masami Hiramatsu <[email protected]>
Cc: Ananth N Mavinakayanahalli <[email protected]>
Cc: Michael Ellerman <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/f1583bc4839a3862cfc2acefcc56f9c8837fa2ba.1487770934.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
include/linux/kprobes.h | 1 +
kernel/kprobes.c | 13 +++++++++++++
2 files changed, 14 insertions(+)
diff --git a/include/linux/kprobes.h b/include/linux/kprobes.h
index 8c0ff78ff45a..1b19416203f0 100644
--- a/include/linux/kprobes.h
+++ b/include/linux/kprobes.h
@@ -266,6 +266,7 @@ extern int arch_init_kprobes(void);
extern void show_registers(struct pt_regs *regs);
extern void kprobes_inc_nmissed_count(struct kprobe *p);
extern bool arch_within_kprobe_blacklist(unsigned long addr);
+extern bool arch_function_offset_within_entry(unsigned long offset);
struct kprobe_insn_cache {
struct mutex mutex;
diff --git a/kernel/kprobes.c b/kernel/kprobes.c
index 0d2f0e7c7605..12d069a3d6a8 100644
--- a/kernel/kprobes.c
+++ b/kernel/kprobes.c
@@ -1823,12 +1823,25 @@ static int pre_handler_kretprobe(struct kprobe *p, struct pt_regs *regs)
}
NOKPROBE_SYMBOL(pre_handler_kretprobe);
+bool __weak arch_function_offset_within_entry(unsigned long offset)
+{
+ return !offset;
+}
+
int register_kretprobe(struct kretprobe *rp)
{
int ret = 0;
struct kretprobe_instance *inst;
int i;
void *addr;
+ unsigned long offset;
+
+ addr = kprobe_addr(&rp->kp);
+ if (!kallsyms_lookup_size_offset((unsigned long)addr, NULL, &offset))
+ return -EINVAL;
+
+ if (!arch_function_offset_within_entry(offset))
+ return -EINVAL;
if (kretprobe_blacklist_size) {
addr = kprobe_addr(&rp->kp);
--
2.14.1
Hello, Sasha!
Following 2 patches must be applied together with the patch:
5e0a39d0f727b35c8b7ef56ba0724c8ceb006297 clocksource/drivers/rockchip_timer: Implement clocksource timer
627988a66aee3c845aa2f1f874a3ddba8adb89d9 ARM: dts: rockchip: Add timer entries to rk3188 SoC
Alexander.
> 4 марта 2018 г., в 1:33, Sasha Levin <[email protected]> написал(а):
>
> From: Alexander Kochetkov <[email protected]>
>
> [ Upstream commit 500d0aa918a2ea6bb918fee8adcf27dc2912bcd1 ]
>
> The clocksource and the sched_clock provided by the arm_global_timer
> are quite unstable because their rates depend on the cpu frequency.
>
> On the other side, the arm_global_timer has a higher rating than the
> rockchip_timer, it will be selected by default by the time framework
> while we want to use the stable rockchip clocksource.
>
> Let's disable the arm_global_timer in order to have the rockchip
> clocksource selected by default.
>
> Signed-off-by: Alexander Kochetkov <[email protected]>
> Signed-off-by: Daniel Lezcano <[email protected]>
> Reviewed-by: Heiko Stuebner <[email protected]>
> Signed-off-by: Sasha Levin <[email protected]>
> ---
> arch/arm/boot/dts/rk3188.dtsi | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
> index ddaada788b45..72b0b4cb538f 100644
> --- a/arch/arm/boot/dts/rk3188.dtsi
> +++ b/arch/arm/boot/dts/rk3188.dtsi
> @@ -404,6 +404,7 @@
>
> &global_timer {
> interrupts = <GIC_PPI 11 0xf04>;
> + status = "disabled";
> };
>
> &local_timer {
> --
> 2.14.1