This is the start of the stable review cycle for the 4.19.14 release.
There are 170 patches in this series, all will be posted as a response
to this one. If anyone has any issues with these being applied, please
let me know.
Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
Anything received after that time might be too late.
The whole patch series can be found in one patch at:
https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.14-rc1.gz
or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
and the diffstat can be found below.
thanks,
greg k-h
-------------
Pseudo-Shortlog of commits:
Greg Kroah-Hartman <[email protected]>
Linux 4.19.14-rc1
Tomas Winkler <[email protected]>
tpm: tpm_i2c_nuvoton: use correct command duration for TPM 2.x
Tomas Winkler <[email protected]>
tpm: tpm_try_transmit() refactor error flow.
Will Deacon <[email protected]>
arm64: compat: Avoid sending SIGILL for unallocated syscall numbers
Robin Murphy <[email protected]>
iommu/arm-smmu-v3: Fix big-endian CMD_SYNC writes
Gustavo A. R. Silva <[email protected]>
KVM: arm/arm64: vgic: Fix off-by-one bug in vgic_get_irq()
Christoffer Dall <[email protected]>
KVM: arm/arm64: vgic-v2: Set active_source to 0 when restoring state
Marc Zyngier <[email protected]>
KVM: arm/arm64: vgic: Cap SPIs to the VM-defined maximum
Julien Thierry <[email protected]>
KVM: arm/arm64: vgic: Do not cond_resched_lock() with IRQs disabled
Maciej W. Rozycki <[email protected]>
rtc: m41t80: Correct alarm month range with RTC reads
Sylwester Nawrocki <[email protected]>
ARM: dts: exynos: Specify I2S assigned clocks in proper node
Marc Zyngier <[email protected]>
arm/arm64: KVM: vgic: Force VM halt when changing the active state of GICv3 PPIs/SGIs
Will Deacon <[email protected]>
arm64: KVM: Avoid setting the upper 32 bits of VTCR_EL2 to 1
Paul Aurich <[email protected]>
smb3: fix large reads on encrypted connections
Georgy A Bystrenin <[email protected]>
CIFS: Fix error mapping for SMB2_LOCK command which caused OFD lock problem
Huacai Chen <[email protected]>
MIPS: Fix a R10000_LLSC_WAR logic in atomic.h
Aaro Koskinen <[email protected]>
MIPS: OCTEON: mark RGMII interface disabled on OCTEON III
Paul Burton <[email protected]>
MIPS: Expand MIPS32 ASIDs to 64 bits
Huacai Chen <[email protected]>
MIPS: Align kernel load address to 64KB
Huacai Chen <[email protected]>
MIPS: Ensure pmd_present() returns false after pmd_mknotpresent()
Huacai Chen <[email protected]>
MIPS: c-r4k: Add r4k_blast_scache_node for Loongson-3
Paul Burton <[email protected]>
MIPS: math-emu: Write-protect delay slot emulation pages
Steven Rostedt (VMware) <[email protected]>
tools lib traceevent: Fix processing of dereferenced args in bprintk events
Hans Verkuil <[email protected]>
media: v4l2-tpg: array index could become negative
Hans Verkuil <[email protected]>
media: vb2: check memory model for VIDIOC_CREATE_BUFS
Hans Verkuil <[email protected]>
media: vivid: free bitmap_cap when updating std/timings/etc.
Luca Ceresoli <[email protected]>
media: imx274: fix stack corruption in imx274_read_reg
Sean Young <[email protected]>
media: rc: cec devices do not have a lirc chardev
Hans Verkuil <[email protected]>
media: cec-pin: fix broken tx_ignore_nack_until_eom error injection
Hans Verkuil <[email protected]>
media: cec: keep track of outstanding transmits
Nava kishore Manne <[email protected]>
serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
Jaegeuk Kim <[email protected]>
f2fs: sanity check of xattr entry size
Martin Blumenstingl <[email protected]>
f2fs: fix validation of the block count in sanity_check_raw_super
Pan Bian <[email protected]>
f2fs: read page index before freeing
Dan Williams <[email protected]>
dax: Use non-exclusive wait in wait_entry_unlocked()
Matthew Wilcox <[email protected]>
dax: Don't access a freed inode
Breno Leitao <[email protected]>
powerpc/tm: Unset MSR[TS] if not recheckpointing
Breno Leitao <[email protected]>
powerpc/tm: Set MSR[TS] just prior to recheckpoint
Lyude Paul <[email protected]>
brcmfmac: Fix out of bounds memory access during fw load
Stijn Tintel <[email protected]>
brcmfmac: fix roamoff=1 modparam
Filipe Manana <[email protected]>
Btrfs: send, fix race with transaction commits that create snapshots
Josef Bacik <[email protected]>
btrfs: run delayed items before dropping the snapshot
Filipe Manana <[email protected]>
Btrfs: fix fsync of files with multiple hard links in new directories
Lu Fengqi <[email protected]>
btrfs: skip file_extent generation check for free_space_inode in run_delalloc_nocow
Anand Jain <[email protected]>
btrfs: dev-replace: go back to suspend state if another EXCL_OP is running
Anand Jain <[email protected]>
btrfs: dev-replace: go back to suspended state if target device is missing
Macpaul Lin <[email protected]>
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
Tejun Heo <[email protected]>
cgroup: fix CSS_TASK_ITER_PROCS
Dmitry Eremin-Solenikov <[email protected]>
crypto: cfb - fix decryption
Dmitry Eremin-Solenikov <[email protected]>
crypto: testmgr - add AES-CFB tests
Atul Gupta <[email protected]>
crypto: chcr - small packet Tx stalls the queue
Wenwen Wang <[email protected]>
crypto: cavium/nitrox - fix a DMA pool free failure
Jernej Skrabec <[email protected]>
clk: sunxi-ng: Use u64 for calculation of NM rate
Johan Jonker <[email protected]>
clk: rockchip: fix typo in rk3188 spdif_frac parent
Lukas Wunner <[email protected]>
spi: bcm2835: Avoid finishing transfer prematurely in IRQ mode
Lukas Wunner <[email protected]>
spi: bcm2835: Fix book-keeping of DMA termination
Lukas Wunner <[email protected]>
spi: bcm2835: Fix race on DMA termination
Theodore Ts'o <[email protected]>
ext4: check for shutdown and r/o file system in ext4_write_inode()
Theodore Ts'o <[email protected]>
ext4: force inode writes when nfsd calls commit_metadata()
Theodore Ts'o <[email protected]>
ext4: avoid declaring fs inconsistent due to invalid file handles
Theodore Ts'o <[email protected]>
ext4: include terminating u32 in size of xattr entries when expanding inodes
ruippan (潘睿) <[email protected]>
ext4: fix EXT4_IOC_GROUP_ADD ioctl
Maurizio Lombardi <[email protected]>
ext4: missing unlock/put_page() in ext4_try_to_write_inline_data()
Pan Bian <[email protected]>
ext4: fix possible use after free in ext4_quota_enable
Theodore Ts'o <[email protected]>
ext4: add ext4_sb_bread() to disambiguate ENOMEM cases
Greg Kurz <[email protected]>
ocxl: Fix endiannes bug in read_afu_name()
Greg Kurz <[email protected]>
ocxl: Fix endiannes bug in ocxl_link_update_pe()
Arnaldo Carvalho de Melo <[email protected]>
perf env: Also consider env->arch == NULL as local operation
Ben Hutchings <[email protected]>
perf pmu: Suppress potential format-truncation warning
Adrian Hunter <[email protected]>
perf script: Use fallbacks for branch stacks
Adrian Hunter <[email protected]>
perf tools: Use fallback for sample_addr_correlates_sym() cases
Adrian Hunter <[email protected]>
perf thread: Add fallback functions for cases where cpumode is insufficient
Adrian Hunter <[email protected]>
perf machine: Record if a arch has a single user/kernel address space
Alexey Brodkin <[email protected]>
clocksource/drivers/arc_timer: Utilize generic sched_clock
Eugeniy Paltsev <[email protected]>
DRM: UDL: get rid of useless vblank initialization
Eric Anholt <[email protected]>
drm/v3d: Skip debugfs dumping GCA on platforms without GCA.
Miquel Raynal <[email protected]>
platform-msi: Free descriptors in platform_msi_domain_free()
Sean Christopherson <[email protected]>
KVM: nVMX: Free the VMREAD/VMWRITE bitmaps if alloc_kvm_area() fails
Marc Zyngier <[email protected]>
arm64: KVM: Make VHE Stage-2 TLB invalidation operations non-interruptible
Sean Christopherson <[email protected]>
KVM: x86: Use jmp to invoke kvm_spurious_fault() from .fixup
Dan Williams <[email protected]>
x86/mm: Drop usage of __flush_tlb_all() in kernel_physical_mapping_init()
Michal Hocko <[email protected]>
x86/speculation/l1tf: Drop the swap storage limit restriction when l1tf=off
Patrick Dreyer <[email protected]>
Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
Sanjeev Chugh <[email protected]>
Input: atmel_mxt_ts - don't try to free unallocated kernel memory
Sebastian Ott <[email protected]>
s390/pci: fix sleeping in atomic during hotplug
Hans de Goede <[email protected]>
ASoC: intel: cht_bsw_max98090_ti: Add pmc_plt_clk_0 quirk for Chromebook Gnawty
Hans de Goede <[email protected]>
ASoC: intel: cht_bsw_max98090_ti: Add pmc_plt_clk_0 quirk for Chromebook Clapper
Colin Ian King <[email protected]>
staging: wilc1000: fix missing read_write setting when reading data
Malcolm Priestley <[email protected]>
media: dvb-usb-v2: Fix incorrect use of transfer_flags URB_FREE_BUFFER
Heikki Krogerus <[email protected]>
usb: roles: Add a description for the class to Kconfig
Stephan Gerhold <[email protected]>
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
Martin Blumenstingl <[email protected]>
usb: dwc2: disable power_down on Amlogic devices
Jia-Ju Bai <[email protected]>
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
Jörgen Storvist <[email protected]>
USB: serial: option: add Fibocom NL678 series
Scott Chen <[email protected]>
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
Terin Stock <[email protected]>
usb: dwc2: host: use hrtimer for NAK retries
Sameer Pujar <[email protected]>
ALSA: hda/tegra: clear pending irq handlers
Jian-Hong Pan <[email protected]>
ALSA: hda/realtek: Enable the headset mic auto detection for ASUS laptops
Takashi Sakamoto <[email protected]>
ALSA: firewire-lib: use the same print format for 'without_header' tracepoints
Takashi Sakamoto <[email protected]>
ALSA: firewire-lib: fix wrong assignment for 'out_packet_without_header' tracepoint
Takashi Sakamoto <[email protected]>
ALSA: firewire-lib: fix wrong handling payload_length as payload_quadlet
Takashi Sakamoto <[email protected]>
ALSA: fireface: fix for state to fetch PCM frames
Wandrille RONCE <[email protected]>
ALSA: hda/realtek: Enable audio jacks of ASUS UX391UA with ALC294
Mantas Mikulėnas <[email protected]>
ALSA: hda: add mute LED support for HP EliteBook 840 G4
Boris Brezillon <[email protected]>
mtd: rawnand: omap2: Pass the parent of pdev to dma_request_chan()
Miquel Raynal <[email protected]>
mtd: rawnand: marvell: prevent timeouts on a loaded machine
Arnd Bergmann <[email protected]>
mtd: atmel-quadspi: disallow building on ebsa110
Diana Craciun <[email protected]>
powerpc/fsl: Fix spectre_v2 mitigations reporting
Gustavo A. R. Silva <[email protected]>
ALSA: emux: Fix potential Spectre v1 vulnerabilities
Gustavo A. R. Silva <[email protected]>
ALSA: pcm: Fix potential Spectre v1 vulnerability
Gustavo A. R. Silva <[email protected]>
ALSA: emu10k1: Fix potential Spectre v1 vulnerabilities
Gustavo A. R. Silva <[email protected]>
ALSA: rme9652: Fix potential Spectre v1 vulnerability
Michael J. Ruhl <[email protected]>
IB/hfi1: Incorrect sizing of sge for PIO will OOPs
Heiner Kallweit <[email protected]>
r8169: fix WoL device wakeup enable
Davide Caratti <[email protected]>
net: Use __kernel_clockid_t in uapi net_stamp.h
Marcin Wojtas <[email protected]>
net: mvneta: fix operation for 64K PAGE_SIZE
Tariq Toukan <[email protected]>
net/mlx5e: RX, Fix wrong early return in receive queue poll
Mikhael Goikhman <[email protected]>
net/mlx5e: Remove unused UDP GSO remaining counter
Shalom Toledo <[email protected]>
mlxsw: core: Increase timeout during firmware flash process
Sudarsana Reddy Kalluru <[email protected]>
qed: Fix command number mismatch between driver and the mfw
Antoine Tenart <[email protected]>
net: mvpp2: fix the phylink mode validation
Moshe Shemesh <[email protected]>
net/mlx5e: RX, Verify MPWQE stride size is in range
Tal Gilboa <[email protected]>
net/mlx5e: Cancel DIM work on close SQ
Allan W. Nielsen <[email protected]>
mscc: Configured MAC entries should be locked.
Stefano Brivio <[email protected]>
ipv6: route: Fix return value of ip6_neigh_lookup() on neigh_create() error
Pieter Jansen van Vuuren <[email protected]>
nfp: flower: ensure TCP flags can be placed in IPv6 frame
Christophe JAILLET <[email protected]>
net/ipv6: Fix a test against 'ipv6_find_idev()' return value
Herbert Xu <[email protected]>
ipv6: frags: Fix bogus skb->sk in reassembled packets
Alaa Hleihel <[email protected]>
net/mlx5e: Remove the false indication of software timestamping support
Cong Wang <[email protected]>
tipc: check group dests after tipc_wait_for_cond()
Yuval Avnery <[email protected]>
net/mlx5: Typo fix in del_sw_hw_rule
Juergen Gross <[email protected]>
xen/netfront: tolerate frags with no data
Jorgen Hansen <[email protected]>
VSOCK: Send reset control packet when socket is partially bound
Jason Wang <[email protected]>
vhost: make sure used idx is seen before log in vhost_add_used_n()
Cong Wang <[email protected]>
tipc: use lock_sock() in tipc_sk_reinit()
Cong Wang <[email protected]>
tipc: fix a double kfree_skb()
Cong Wang <[email protected]>
tipc: fix a double free in tipc_enable_bearer()
Cong Wang <[email protected]>
tipc: compare remote and local protocols in tipc_udp_enable()
Cong Wang <[email protected]>
tipc: check tsk->group in tipc_wait_for_cond()
Eric Dumazet <[email protected]>
tcp: fix a race in inet_diag_dump_icsk()
Deepa Dinamani <[email protected]>
sock: Make sock->sk_stamp thread-safe
Xin Long <[email protected]>
sctp: initialize sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event
Jörgen Storvist <[email protected]>
qmi_wwan: Add support for Fibocom NL678 series
Jörgen Storvist <[email protected]>
qmi_wwan: Added support for Telit LN940 series
Jörgen Storvist <[email protected]>
qmi_wwan: Added support for Fibocom NL668 series
Cong Wang <[email protected]>
ptr_ring: wrap back ->producer in __ptr_ring_swap_queue()
Gustavo A. R. Silva <[email protected]>
phonet: af_phonet: Fix Spectre v1 vulnerability
Willem de Bruijn <[email protected]>
packet: validate address length if non-zero
Willem de Bruijn <[email protected]>
packet: validate address length
Cong Wang <[email protected]>
net/wan: fix a double free in x25_asy_open_tty()
Ganesh Goudar <[email protected]>
net/tls: allocate tls context using GFP_ATOMIC
Dan Carpenter <[email protected]>
net: stmmac: Fix an error code in probe()
Myungho Jung <[email protected]>
net/smc: fix TCP fallback socket release
Cong Wang <[email protected]>
netrom: fix locking in nr_find_socket()
Kunihiko Hayashi <[email protected]>
net: phy: Fix the issue that netif always links up after resuming
Antoine Tenart <[email protected]>
net: mvpp2: 10G modes aren't supported on all ports
Claudiu Beznea <[email protected]>
net: macb: restart tx after tx used bit read
Michal Kubecek <[email protected]>
net: ipv4: do not handle duplicate fragments as overlapping
Eric Dumazet <[email protected]>
net/hamradio/6pack: use mod_timer() to rearm timers
Gustavo A. R. Silva <[email protected]>
net: core: Fix Spectre v1 vulnerability
Eric Dumazet <[email protected]>
net: clear skb->tstamp in forwarding paths
Eric Dumazet <[email protected]>
isdn: fix kernel-infoleak in capi_unlocked_ioctl
Willem de Bruijn <[email protected]>
ip: validate header length on virtual device xmit
Eric Dumazet <[email protected]>
ipv6: tunnels: fix two use-after-free
Cong Wang <[email protected]>
ipv6: explicitly initialize udp6_addr in udp_sock_create6()
Gustavo A. R. Silva <[email protected]>
ipv4: Fix potential Spectre v1 vulnerability
Gustavo A. R. Silva <[email protected]>
ip6mr: Fix potential Spectre v1 vulnerability
Willem de Bruijn <[email protected]>
ieee802154: lowpan_header_create check must check daddr
Tyrel Datwyler <[email protected]>
ibmveth: fix DMA unmap error in ibmveth_xmit_start error path
Lorenzo Bianconi <[email protected]>
gro_cell: add napi_disable in gro_cells_destroy
Cong Wang <[email protected]>
ax25: fix a use-after-free in ax25_fillin_cb()
-------------
Diffstat:
Documentation/admin-guide/kernel-parameters.txt | 3 +
Documentation/admin-guide/l1tf.rst | 6 +-
Makefile | 4 +-
arch/arc/Kconfig | 1 +
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 9 ++-
arch/arm/boot/dts/exynos5422-odroidxu4.dts | 9 ++-
arch/arm64/include/asm/kvm_arm.h | 2 +-
arch/arm64/include/asm/unistd.h | 5 +-
arch/arm64/kernel/sys_compat.c | 4 +-
arch/arm64/kvm/hyp/tlb.c | 35 ++++++---
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c | 7 +-
arch/mips/cavium-octeon/executive/cvmx-helper.c | 3 +-
arch/mips/include/asm/atomic.h | 2 +-
arch/mips/include/asm/cpu-info.h | 2 +-
arch/mips/include/asm/mach-generic/mmzone.h | 2 +
arch/mips/include/asm/mach-loongson64/mmzone.h | 1 +
arch/mips/include/asm/mmu.h | 2 +-
arch/mips/include/asm/mmu_context.h | 10 ++-
arch/mips/include/asm/mmzone.h | 8 +++
arch/mips/include/asm/pgtable-64.h | 5 ++
arch/mips/include/asm/r4kcache.h | 22 ++++++
arch/mips/kernel/vdso.c | 4 +-
arch/mips/math-emu/dsemul.c | 38 +++++-----
arch/mips/mm/c-r3k.c | 2 +-
arch/mips/mm/c-r4k.c | 44 ++++++++++--
arch/powerpc/kernel/security.c | 2 +-
arch/powerpc/kernel/signal_32.c | 38 ++++++++--
arch/powerpc/kernel/signal_64.c | 64 ++++++++++++-----
arch/s390/pci/pci_clp.c | 2 +-
arch/x86/include/asm/kvm_host.h | 2 +-
arch/x86/kernel/cpu/bugs.c | 3 +-
arch/x86/kvm/vmx.c | 7 +-
arch/x86/mm/init.c | 2 +-
arch/x86/mm/init_64.c | 6 --
crypto/cfb.c | 2 +-
crypto/tcrypt.c | 5 ++
crypto/testmgr.c | 7 ++
crypto/testmgr.h | 76 ++++++++++++++++++++
drivers/base/platform-msi.c | 6 +-
drivers/char/tpm/tpm-interface.c | 15 ++--
drivers/char/tpm/tpm_i2c_nuvoton.c | 11 +--
drivers/clk/rockchip/clk-rk3188.c | 2 +-
drivers/clk/sunxi-ng/ccu_nm.c | 18 ++++-
drivers/clocksource/Kconfig | 1 +
drivers/clocksource/arc_timer.c | 22 ++++++
drivers/crypto/cavium/nitrox/nitrox_algs.c | 12 ++--
drivers/crypto/cavium/nitrox/nitrox_lib.c | 22 ++++--
drivers/crypto/cavium/nitrox/nitrox_req.h | 7 ++
drivers/crypto/chelsio/chcr_ipsec.c | 5 +-
drivers/gpu/drm/udl/udl_main.c | 7 +-
drivers/gpu/drm/v3d/v3d_debugfs.c | 11 +--
drivers/infiniband/hw/hfi1/verbs.c | 2 +
drivers/input/mouse/elan_i2c_core.c | 1 +
drivers/input/touchscreen/atmel_mxt_ts.c | 4 +-
drivers/iommu/arm-smmu-v3.c | 8 ++-
drivers/isdn/capi/kcapi.c | 4 +-
drivers/media/cec/cec-adap.c | 27 ++++---
drivers/media/cec/cec-pin.c | 5 +-
drivers/media/common/v4l2-tpg/v4l2-tpg-core.c | 2 +-
drivers/media/common/videobuf2/videobuf2-core.c | 3 +
drivers/media/i2c/imx274.c | 7 +-
drivers/media/platform/vivid/vivid-vid-cap.c | 2 +
drivers/media/rc/rc-main.c | 6 +-
drivers/media/usb/dvb-usb-v2/usb_urb.c | 5 +-
drivers/misc/ocxl/config.c | 2 +-
drivers/misc/ocxl/link.c | 2 +-
drivers/mtd/nand/raw/marvell_nand.c | 17 ++++-
drivers/mtd/nand/raw/omap2.c | 2 +-
drivers/mtd/spi-nor/Kconfig | 2 +-
drivers/net/ethernet/cadence/macb_main.c | 21 +++++-
drivers/net/ethernet/ibm/ibmveth.c | 6 +-
drivers/net/ethernet/marvell/mvneta.c | 6 +-
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 16 +++--
.../net/ethernet/mellanox/mlx5/core/en_ethtool.c | 11 +--
drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 6 ++
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c | 10 +--
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c | 2 -
drivers/net/ethernet/mellanox/mlx5/core/en_stats.h | 2 -
drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 2 +-
drivers/net/ethernet/mellanox/mlxsw/core.c | 19 ++++-
drivers/net/ethernet/mellanox/mlxsw/core.h | 3 +
drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 7 +-
drivers/net/ethernet/mscc/ocelot.c | 2 +-
.../net/ethernet/netronome/nfp/flower/offload.c | 28 ++++++--
drivers/net/ethernet/qlogic/qed/qed_hsi.h | 3 +-
drivers/net/ethernet/realtek/r8169.c | 4 +-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 1 +
drivers/net/hamradio/6pack.c | 16 ++---
drivers/net/phy/phy_device.c | 7 +-
drivers/net/usb/qmi_wwan.c | 3 +
drivers/net/wan/x25_asy.c | 2 +
.../broadcom/brcm80211/brcmfmac/cfg80211.c | 11 ++-
.../broadcom/brcm80211/brcmfmac/cfg80211.h | 2 +-
.../wireless/broadcom/brcm80211/brcmfmac/core.c | 2 +-
.../broadcom/brcm80211/brcmfmac/firmware.c | 8 ++-
drivers/net/xen-netfront.c | 2 +-
drivers/rtc/rtc-m41t80.c | 2 +-
drivers/spi/spi-bcm2835.c | 14 ++--
drivers/staging/wilc1000/wilc_sdio.c | 1 +
drivers/tty/serial/xilinx_uartps.c | 4 +-
drivers/usb/Kconfig | 4 --
drivers/usb/class/cdc-acm.c | 10 +++
drivers/usb/class/cdc-acm.h | 1 +
drivers/usb/common/Makefile | 1 -
drivers/usb/dwc2/hcd.h | 2 +-
drivers/usb/dwc2/hcd_queue.c | 19 +++--
drivers/usb/dwc2/params.c | 1 +
drivers/usb/dwc3/dwc3-pci.c | 8 +--
drivers/usb/host/r8a66597-hcd.c | 5 +-
drivers/usb/roles/Kconfig | 13 ++++
drivers/usb/roles/Makefile | 4 +-
drivers/usb/{common/roles.c => roles/class.c} | 0
drivers/usb/serial/option.c | 4 ++
drivers/usb/serial/pl2303.c | 5 ++
drivers/usb/serial/pl2303.h | 5 ++
drivers/vhost/vhost.c | 2 +
fs/btrfs/btrfs_inode.h | 6 ++
fs/btrfs/ctree.c | 29 ++++++--
fs/btrfs/dev-replace.c | 6 ++
fs/btrfs/extent-tree.c | 4 ++
fs/btrfs/inode.c | 20 +++++-
fs/btrfs/tree-log.c | 16 +++++
fs/cifs/smb2maperror.c | 4 +-
fs/cifs/smb2ops.c | 4 +-
fs/dax.c | 69 ++++++++----------
fs/ext4/ext4.h | 17 ++++-
fs/ext4/ialloc.c | 2 +-
fs/ext4/inline.c | 5 +-
fs/ext4/inode.c | 63 +++++++++++-----
fs/ext4/ioctl.c | 2 +-
fs/ext4/migrate.c | 36 +++++-----
fs/ext4/namei.c | 4 +-
fs/ext4/resize.c | 79 ++++++++++----------
fs/ext4/super.c | 55 ++++++++++----
fs/ext4/xattr.c | 83 +++++++++++-----------
fs/f2fs/node.c | 4 +-
fs/f2fs/super.c | 6 +-
fs/f2fs/xattr.c | 18 +++--
include/linux/msi.h | 2 +
include/linux/ptr_ring.h | 2 +
include/media/cec.h | 1 +
include/net/ip_tunnels.h | 20 ++++++
include/net/sock.h | 38 +++++++++-
include/trace/events/ext4.h | 20 ++++++
include/uapi/linux/net_tstamp.h | 4 +-
kernel/cgroup/cgroup.c | 29 ++++----
net/ax25/af_ax25.c | 11 ++-
net/ax25/ax25_dev.c | 2 +
net/compat.c | 15 ++--
net/core/filter.c | 2 +
net/core/gro_cells.c | 1 +
net/core/sock.c | 15 ++--
net/ieee802154/6lowpan/tx.c | 3 +
net/ipv4/inet_diag.c | 4 +-
net/ipv4/ip_forward.c | 1 +
net/ipv4/ip_fragment.c | 18 +++--
net/ipv4/ip_gre.c | 9 +++
net/ipv4/ip_tunnel.c | 9 ---
net/ipv4/ip_vti.c | 12 +++-
net/ipv4/ipmr.c | 4 ++
net/ipv6/addrconf.c | 4 +-
net/ipv6/ip6_gre.c | 10 ++-
net/ipv6/ip6_output.c | 1 +
net/ipv6/ip6_tunnel.c | 11 ++-
net/ipv6/ip6_udp_tunnel.c | 3 +-
net/ipv6/ip6_vti.c | 9 +--
net/ipv6/ip6mr.c | 21 ++++--
net/ipv6/reassembly.c | 1 +
net/ipv6/route.c | 4 +-
net/ipv6/sit.c | 3 +
net/netrom/af_netrom.c | 15 ++--
net/packet/af_packet.c | 8 ++-
net/phonet/af_phonet.c | 3 +
net/sctp/ipv6.c | 1 +
net/smc/af_smc.c | 14 +++-
net/smc/smc.h | 4 ++
net/sunrpc/svcsock.c | 2 +-
net/tipc/bearer.c | 1 -
net/tipc/socket.c | 40 ++++++-----
net/tipc/udp_media.c | 9 ++-
net/tls/tls_main.c | 2 +-
net/vmw_vsock/vmci_transport.c | 67 ++++++++++++-----
sound/core/pcm.c | 2 +
sound/firewire/amdtp-stream-trace.h | 4 +-
sound/firewire/amdtp-stream.c | 4 +-
sound/firewire/fireface/ff-protocol-ff400.c | 2 +-
sound/pci/emu10k1/emufx.c | 5 ++
sound/pci/hda/hda_tegra.c | 2 +
sound/pci/hda/patch_conexant.c | 1 +
sound/pci/hda/patch_realtek.c | 3 +-
sound/pci/rme9652/hdsp.c | 10 +--
sound/soc/intel/boards/cht_bsw_max98090_ti.c | 14 ++++
sound/synth/emux/emux_hwdep.c | 7 +-
tools/lib/traceevent/event-parse.c | 1 +
tools/perf/arch/common.c | 10 +++
tools/perf/arch/common.h | 1 +
tools/perf/builtin-script.c | 12 ++--
tools/perf/util/env.c | 2 +-
tools/perf/util/event.c | 29 +++++++-
tools/perf/util/machine.c | 27 +++++++
tools/perf/util/machine.h | 3 +
tools/perf/util/pmu.c | 8 +--
.../util/scripting-engines/trace-event-python.c | 16 ++---
tools/perf/util/session.c | 4 ++
tools/perf/util/thread.h | 4 ++
virt/kvm/arm/vgic/vgic-mmio.c | 44 ++++++------
virt/kvm/arm/vgic/vgic.c | 6 +-
207 files changed, 1553 insertions(+), 648 deletions(-)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <[email protected]>
[ Upstream commit d63967e475ae10f286dbd35e189cb241e0b1f284 ]
Since capi_ioctl() copies 64 bytes after calling
capi20_get_manufacturer() we need to ensure to not leak
information to user.
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
CPU: 0 PID: 11245 Comm: syz-executor633 Not tainted 4.20.0-rc7+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613
kmsan_internal_check_memory+0x9d4/0xb00 mm/kmsan/kmsan.c:704
kmsan_copy_to_user+0xab/0xc0 mm/kmsan/kmsan_hooks.c:601
_copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
capi_ioctl include/linux/uaccess.h:177 [inline]
capi_unlocked_ioctl+0x1a0b/0x1bf0 drivers/isdn/capi/capi.c:939
do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46
ksys_ioctl fs/ioctl.c:713 [inline]
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl+0x1da/0x270 fs/ioctl.c:718
__x64_sys_ioctl+0x4a/0x70 fs/ioctl.c:718
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x440019
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffdd4659fb8 EFLAGS: 00000213 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440019
RDX: 0000000020000080 RSI: 00000000c0044306 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8
R10: 0000000000000000 R11: 0000000000000213 R12: 00000000004018a0
R13: 0000000000401930 R14: 0000000000000000 R15: 0000000000000000
Local variable description: ----data.i@capi_unlocked_ioctl
Variable was created at:
capi_ioctl drivers/isdn/capi/capi.c:747 [inline]
capi_unlocked_ioctl+0x82/0x1bf0 drivers/isdn/capi/capi.c:939
do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46
Bytes 12-63 of 64 are uninitialized
Memory access of size 64 starts at ffff88807ac5fce8
Data copied to user address 0000000020000080
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Cc: Karsten Keil <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/isdn/capi/kcapi.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/isdn/capi/kcapi.c
+++ b/drivers/isdn/capi/kcapi.c
@@ -852,7 +852,7 @@ u16 capi20_get_manufacturer(u32 contr, u
u16 ret;
if (contr == 0) {
- strlcpy(buf, capi_manufakturer, CAPI_MANUFACTURER_LEN);
+ strncpy(buf, capi_manufakturer, CAPI_MANUFACTURER_LEN);
return CAPI_NOERROR;
}
@@ -860,7 +860,7 @@ u16 capi20_get_manufacturer(u32 contr, u
ctr = get_capi_ctr_by_nr(contr);
if (ctr && ctr->state == CAPI_CTR_RUNNING) {
- strlcpy(buf, ctr->manu, CAPI_MANUFACTURER_LEN);
+ strncpy(buf, ctr->manu, CAPI_MANUFACTURER_LEN);
ret = CAPI_NOERROR;
} else
ret = CAPI_REGNOTINSTALLED;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: "Gustavo A. R. Silva" <[email protected]>
[ Upstream commit 50d5258634aee2e62832aa086d2fb0de00e72b91 ]
flen is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/core/filter.c:1101 bpf_check_classic() warn: potential spectre issue 'filter' [w]
Fix this by sanitizing flen before using it to index filter at line 1101:
switch (filter[flen - 1].code) {
and through pc at line 1040:
const struct sock_filter *ftest = &filter[pc];
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/core/filter.c | 2 ++
1 file changed, 2 insertions(+)
--- a/net/core/filter.c
+++ b/net/core/filter.c
@@ -68,6 +68,7 @@
#include <linux/seg6_local.h>
#include <net/seg6.h>
#include <net/seg6_local.h>
+#include <linux/nospec.h>
/**
* sk_filter_trim_cap - run a packet through a socket filter
@@ -1033,6 +1034,7 @@ static int bpf_check_classic(const struc
bool anc_found;
int pc;
+ flen = array_index_nospec(flen, BPF_MAXINSNS + 1);
/* Check the filter code now */
for (pc = 0; pc < flen; pc++) {
const struct sock_filter *ftest = &filter[pc];
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michal Kubecek <[email protected]>
[ Upstream commit ade446403bfb79d3528d56071a84b15351a139ad ]
Since commit 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.
Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.
v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)
Fixes: 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping segments.")
Signed-off-by: Michal Kubecek <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv4/ip_fragment.c | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
--- a/net/ipv4/ip_fragment.c
+++ b/net/ipv4/ip_fragment.c
@@ -347,10 +347,10 @@ static int ip_frag_queue(struct ipq *qp,
struct net *net = container_of(qp->q.net, struct net, ipv4.frags);
struct rb_node **rbn, *parent;
struct sk_buff *skb1, *prev_tail;
+ int ihl, end, skb1_run_end;
struct net_device *dev;
unsigned int fragsize;
int flags, offset;
- int ihl, end;
int err = -ENOENT;
u8 ecn;
@@ -420,7 +420,9 @@ static int ip_frag_queue(struct ipq *qp,
* overlapping fragment, the entire datagram (and any constituent
* fragments) MUST be silently discarded.
*
- * We do the same here for IPv4 (and increment an snmp counter).
+ * We do the same here for IPv4 (and increment an snmp counter) but
+ * we do not want to drop the whole queue in response to a duplicate
+ * fragment.
*/
/* Find out where to put this fragment. */
@@ -444,13 +446,17 @@ static int ip_frag_queue(struct ipq *qp,
do {
parent = *rbn;
skb1 = rb_to_skb(parent);
+ skb1_run_end = skb1->ip_defrag_offset +
+ FRAG_CB(skb1)->frag_run_len;
if (end <= skb1->ip_defrag_offset)
rbn = &parent->rb_left;
- else if (offset >= skb1->ip_defrag_offset +
- FRAG_CB(skb1)->frag_run_len)
+ else if (offset >= skb1_run_end)
rbn = &parent->rb_right;
- else /* Found an overlap with skb1. */
- goto discard_qp;
+ else if (offset >= skb1->ip_defrag_offset &&
+ end <= skb1_run_end)
+ goto err; /* No new data, potential duplicate */
+ else
+ goto discard_qp; /* Found an overlap */
} while (*rbn);
/* Here we have parent properly set, and rbn pointing to
* one of its NULL left/right children. Insert skb.
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Antoine Tenart <[email protected]>
[ Upstream commit 006791772084383de779ef29f2e06f3a6e111e7d ]
The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.
Fixes: 01b3fd5ac97c ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <[email protected]>
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 14 ++++++++------
1 file changed, 8 insertions(+), 6 deletions(-)
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4292,12 +4292,14 @@ static void mvpp2_phylink_validate(struc
case PHY_INTERFACE_MODE_10GKR:
case PHY_INTERFACE_MODE_XAUI:
case PHY_INTERFACE_MODE_NA:
- phylink_set(mask, 10000baseCR_Full);
- phylink_set(mask, 10000baseSR_Full);
- phylink_set(mask, 10000baseLR_Full);
- phylink_set(mask, 10000baseLRM_Full);
- phylink_set(mask, 10000baseER_Full);
- phylink_set(mask, 10000baseKR_Full);
+ if (port->gop_id == 0) {
+ phylink_set(mask, 10000baseCR_Full);
+ phylink_set(mask, 10000baseSR_Full);
+ phylink_set(mask, 10000baseLR_Full);
+ phylink_set(mask, 10000baseLRM_Full);
+ phylink_set(mask, 10000baseER_Full);
+ phylink_set(mask, 10000baseKR_Full);
+ }
/* Fall-through */
case PHY_INTERFACE_MODE_RGMII:
case PHY_INTERFACE_MODE_RGMII_ID:
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Willem de Bruijn <[email protected]>
[ Upstream commit cb9f1b783850b14cbd7f87d061d784a666dfba1f ]
KMSAN detected read beyond end of buffer in vti and sit devices when
passing truncated packets with PF_PACKET. The issue affects additional
ip tunnel devices.
Extend commit 76c0ddd8c3a6 ("ip6_tunnel: be careful when accessing the
inner header") and commit ccfec9e5cb2d ("ip_tunnel: be careful when
accessing the inner header").
Move the check to a separate helper and call at the start of each
ndo_start_xmit function in net/ipv4 and net/ipv6.
Minor changes:
- convert dev_kfree_skb to kfree_skb on error path,
as dev_kfree_skb calls consume_skb which is not for error paths.
- use pskb_network_may_pull even though that is pedantic here,
as the same as pskb_may_pull for devices without llheaders.
- do not cache ipv6 hdrs if used only once
(unsafe across pskb_may_pull, was more relevant to earlier patch)
Reported-by: syzbot <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/net/ip_tunnels.h | 20 ++++++++++++++++++++
net/ipv4/ip_gre.c | 9 +++++++++
net/ipv4/ip_tunnel.c | 9 ---------
net/ipv4/ip_vti.c | 12 +++++++++---
net/ipv6/ip6_gre.c | 10 +++++++---
net/ipv6/ip6_tunnel.c | 10 +++-------
net/ipv6/ip6_vti.c | 8 ++++----
net/ipv6/ip6mr.c | 17 +++++++++++------
net/ipv6/sit.c | 3 +++
9 files changed, 66 insertions(+), 32 deletions(-)
--- a/include/net/ip_tunnels.h
+++ b/include/net/ip_tunnels.h
@@ -326,6 +326,26 @@ int ip_tunnel_encap_del_ops(const struct
int ip_tunnel_encap_setup(struct ip_tunnel *t,
struct ip_tunnel_encap *ipencap);
+static inline bool pskb_inet_may_pull(struct sk_buff *skb)
+{
+ int nhlen;
+
+ switch (skb->protocol) {
+#if IS_ENABLED(CONFIG_IPV6)
+ case htons(ETH_P_IPV6):
+ nhlen = sizeof(struct ipv6hdr);
+ break;
+#endif
+ case htons(ETH_P_IP):
+ nhlen = sizeof(struct iphdr);
+ break;
+ default:
+ nhlen = 0;
+ }
+
+ return pskb_network_may_pull(skb, nhlen);
+}
+
static inline int ip_encap_hlen(struct ip_tunnel_encap *e)
{
const struct ip_tunnel_encap_ops *ops;
--- a/net/ipv4/ip_gre.c
+++ b/net/ipv4/ip_gre.c
@@ -677,6 +677,9 @@ static netdev_tx_t ipgre_xmit(struct sk_
struct ip_tunnel *tunnel = netdev_priv(dev);
const struct iphdr *tnl_params;
+ if (!pskb_inet_may_pull(skb))
+ goto free_skb;
+
if (tunnel->collect_md) {
gre_fb_xmit(skb, dev, skb->protocol);
return NETDEV_TX_OK;
@@ -720,6 +723,9 @@ static netdev_tx_t erspan_xmit(struct sk
struct ip_tunnel *tunnel = netdev_priv(dev);
bool truncate = false;
+ if (!pskb_inet_may_pull(skb))
+ goto free_skb;
+
if (tunnel->collect_md) {
erspan_fb_xmit(skb, dev, skb->protocol);
return NETDEV_TX_OK;
@@ -763,6 +769,9 @@ static netdev_tx_t gre_tap_xmit(struct s
{
struct ip_tunnel *tunnel = netdev_priv(dev);
+ if (!pskb_inet_may_pull(skb))
+ goto free_skb;
+
if (tunnel->collect_md) {
gre_fb_xmit(skb, dev, htons(ETH_P_TEB));
return NETDEV_TX_OK;
--- a/net/ipv4/ip_tunnel.c
+++ b/net/ipv4/ip_tunnel.c
@@ -627,7 +627,6 @@ void ip_tunnel_xmit(struct sk_buff *skb,
const struct iphdr *tnl_params, u8 protocol)
{
struct ip_tunnel *tunnel = netdev_priv(dev);
- unsigned int inner_nhdr_len = 0;
const struct iphdr *inner_iph;
struct flowi4 fl4;
u8 tos, ttl;
@@ -637,14 +636,6 @@ void ip_tunnel_xmit(struct sk_buff *skb,
__be32 dst;
bool connected;
- /* ensure we can access the inner net header, for several users below */
- if (skb->protocol == htons(ETH_P_IP))
- inner_nhdr_len = sizeof(struct iphdr);
- else if (skb->protocol == htons(ETH_P_IPV6))
- inner_nhdr_len = sizeof(struct ipv6hdr);
- if (unlikely(!pskb_may_pull(skb, inner_nhdr_len)))
- goto tx_error;
-
inner_iph = (const struct iphdr *)skb_inner_network_header(skb);
connected = (tunnel->parms.iph.daddr != 0);
--- a/net/ipv4/ip_vti.c
+++ b/net/ipv4/ip_vti.c
@@ -241,6 +241,9 @@ static netdev_tx_t vti_tunnel_xmit(struc
struct ip_tunnel *tunnel = netdev_priv(dev);
struct flowi fl;
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
memset(&fl, 0, sizeof(fl));
switch (skb->protocol) {
@@ -253,15 +256,18 @@ static netdev_tx_t vti_tunnel_xmit(struc
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
break;
default:
- dev->stats.tx_errors++;
- dev_kfree_skb(skb);
- return NETDEV_TX_OK;
+ goto tx_err;
}
/* override mark with tunnel output key */
fl.flowi_mark = be32_to_cpu(tunnel->parms.o_key);
return vti_xmit(skb, dev, &fl);
+
+tx_err:
+ dev->stats.tx_errors++;
+ kfree_skb(skb);
+ return NETDEV_TX_OK;
}
static int vti4_err(struct sk_buff *skb, u32 info)
--- a/net/ipv6/ip6_gre.c
+++ b/net/ipv6/ip6_gre.c
@@ -897,6 +897,9 @@ static netdev_tx_t ip6gre_tunnel_xmit(st
struct net_device_stats *stats = &t->dev->stats;
int ret;
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
if (!ip6_tnl_xmit_ctl(t, &t->parms.laddr, &t->parms.raddr))
goto tx_err;
@@ -939,6 +942,9 @@ static netdev_tx_t ip6erspan_tunnel_xmit
int nhoff;
int thoff;
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
if (!ip6_tnl_xmit_ctl(t, &t->parms.laddr, &t->parms.raddr))
goto tx_err;
@@ -1011,8 +1017,6 @@ static netdev_tx_t ip6erspan_tunnel_xmit
goto tx_err;
}
} else {
- struct ipv6hdr *ipv6h = ipv6_hdr(skb);
-
switch (skb->protocol) {
case htons(ETH_P_IP):
memset(&(IPCB(skb)->opt), 0, sizeof(IPCB(skb)->opt));
@@ -1020,7 +1024,7 @@ static netdev_tx_t ip6erspan_tunnel_xmit
&dsfield, &encap_limit);
break;
case htons(ETH_P_IPV6):
- if (ipv6_addr_equal(&t->parms.raddr, &ipv6h->saddr))
+ if (ipv6_addr_equal(&t->parms.raddr, &ipv6_hdr(skb)->saddr))
goto tx_err;
if (prepare_ip6gre_xmit_ipv6(skb, dev, &fl6,
&dsfield, &encap_limit))
--- a/net/ipv6/ip6_tunnel.c
+++ b/net/ipv6/ip6_tunnel.c
@@ -1243,10 +1243,6 @@ ip4ip6_tnl_xmit(struct sk_buff *skb, str
u8 tproto;
int err;
- /* ensure we can access the full inner ip header */
- if (!pskb_may_pull(skb, sizeof(struct iphdr)))
- return -1;
-
iph = ip_hdr(skb);
memset(&(IPCB(skb)->opt), 0, sizeof(IPCB(skb)->opt));
@@ -1321,9 +1317,6 @@ ip6ip6_tnl_xmit(struct sk_buff *skb, str
u8 tproto;
int err;
- if (unlikely(!pskb_may_pull(skb, sizeof(*ipv6h))))
- return -1;
-
ipv6h = ipv6_hdr(skb);
tproto = READ_ONCE(t->parms.proto);
if ((tproto != IPPROTO_IPV6 && tproto != 0) ||
@@ -1405,6 +1398,9 @@ ip6_tnl_start_xmit(struct sk_buff *skb,
struct net_device_stats *stats = &t->dev->stats;
int ret;
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
switch (skb->protocol) {
case htons(ETH_P_IP):
ret = ip4ip6_tnl_xmit(skb, dev);
--- a/net/ipv6/ip6_vti.c
+++ b/net/ipv6/ip6_vti.c
@@ -522,18 +522,18 @@ vti6_tnl_xmit(struct sk_buff *skb, struc
{
struct ip6_tnl *t = netdev_priv(dev);
struct net_device_stats *stats = &t->dev->stats;
- struct ipv6hdr *ipv6h;
struct flowi fl;
int ret;
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
memset(&fl, 0, sizeof(fl));
switch (skb->protocol) {
case htons(ETH_P_IPV6):
- ipv6h = ipv6_hdr(skb);
-
if ((t->parms.proto != IPPROTO_IPV6 && t->parms.proto != 0) ||
- vti6_addr_conflict(t, ipv6h))
+ vti6_addr_conflict(t, ipv6_hdr(skb)))
goto tx_err;
xfrm_decode_session(skb, &fl, AF_INET6);
--- a/net/ipv6/ip6mr.c
+++ b/net/ipv6/ip6mr.c
@@ -51,6 +51,7 @@
#include <linux/export.h>
#include <net/ip6_checksum.h>
#include <linux/netconf.h>
+#include <net/ip_tunnels.h>
#include <linux/nospec.h>
@@ -593,13 +594,12 @@ static netdev_tx_t reg_vif_xmit(struct s
.flowi6_iif = skb->skb_iif ? : LOOPBACK_IFINDEX,
.flowi6_mark = skb->mark,
};
- int err;
- err = ip6mr_fib_lookup(net, &fl6, &mrt);
- if (err < 0) {
- kfree_skb(skb);
- return err;
- }
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
+ if (ip6mr_fib_lookup(net, &fl6, &mrt) < 0)
+ goto tx_err;
read_lock(&mrt_lock);
dev->stats.tx_bytes += skb->len;
@@ -608,6 +608,11 @@ static netdev_tx_t reg_vif_xmit(struct s
read_unlock(&mrt_lock);
kfree_skb(skb);
return NETDEV_TX_OK;
+
+tx_err:
+ dev->stats.tx_errors++;
+ kfree_skb(skb);
+ return NETDEV_TX_OK;
}
static int reg_vif_get_iflink(const struct net_device *dev)
--- a/net/ipv6/sit.c
+++ b/net/ipv6/sit.c
@@ -1021,6 +1021,9 @@ tx_error:
static netdev_tx_t sit_tunnel_xmit(struct sk_buff *skb,
struct net_device *dev)
{
+ if (!pskb_inet_may_pull(skb))
+ goto tx_err;
+
switch (skb->protocol) {
case htons(ETH_P_IP):
sit_tunnel_xmit__(skb, dev, IPPROTO_IPIP);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Ganesh Goudar <[email protected]>
[ Upstream commit c6ec179a0082e2e76e3a72050c2b99d3d0f3da3f ]
create_ctx can be called from atomic context, hence use
GFP_ATOMIC instead of GFP_KERNEL.
[ 395.962599] BUG: sleeping function called from invalid context at mm/slab.h:421
[ 395.979896] in_atomic(): 1, irqs_disabled(): 0, pid: 16254, name: openssl
[ 395.996564] 2 locks held by openssl/16254:
[ 396.010492] #0: 00000000347acb52 (sk_lock-AF_INET){+.+.}, at: do_tcp_setsockopt.isra.44+0x13b/0x9a0
[ 396.029838] #1: 000000006c9552b5 (device_spinlock){+...}, at: tls_init+0x1d/0x280
[ 396.047675] CPU: 5 PID: 16254 Comm: openssl Tainted: G O 4.20.0-rc6+ #25
[ 396.066019] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0c 09/25/2017
[ 396.083537] Call Trace:
[ 396.096265] dump_stack+0x5e/0x8b
[ 396.109876] ___might_sleep+0x216/0x250
[ 396.123940] kmem_cache_alloc_trace+0x1b0/0x240
[ 396.138800] create_ctx+0x1f/0x60
[ 396.152504] tls_init+0xbd/0x280
[ 396.166135] tcp_set_ulp+0x191/0x2d0
[ 396.180035] ? tcp_set_ulp+0x2c/0x2d0
[ 396.193960] do_tcp_setsockopt.isra.44+0x148/0x9a0
[ 396.209013] __sys_setsockopt+0x7c/0xe0
[ 396.223054] __x64_sys_setsockopt+0x20/0x30
[ 396.237378] do_syscall_64+0x4a/0x180
[ 396.251200] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: df9d4a178022 ("net/tls: sleeping function from invalid context")
Signed-off-by: Ganesh Goudar <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tls/tls_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/net/tls/tls_main.c
+++ b/net/tls/tls_main.c
@@ -550,7 +550,7 @@ static struct tls_context *create_ctx(st
struct inet_connection_sock *icsk = inet_csk(sk);
struct tls_context *ctx;
- ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+ ctx = kzalloc(sizeof(*ctx), GFP_ATOMIC);
if (!ctx)
return NULL;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <[email protected]>
[ Upstream commit cbb49697d5512ce9e61b45ce75d3ee43d7ea5524 ]
xfrm6_policy_check() might have re-allocated skb->head, we need
to reload ipv6 header pointer.
sysbot reported :
BUG: KASAN: use-after-free in __ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40
Read of size 4 at addr ffff888191b8cb70 by task syz-executor2/1304
CPU: 0 PID: 1304 Comm: syz-executor2 Not tainted 4.20.0-rc7+ #356
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.8+0x242/0x309 mm/kasan/report.c:412
__asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:432
__ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40
ipv6_addr_type include/net/ipv6.h:403 [inline]
ip6_tnl_get_cap+0x27/0x190 net/ipv6/ip6_tunnel.c:727
ip6_tnl_rcv_ctl+0xdb/0x2a0 net/ipv6/ip6_tunnel.c:757
vti6_rcv+0x336/0x8f3 net/ipv6/ip6_vti.c:321
xfrm6_ipcomp_rcv+0x1a5/0x3a0 net/ipv6/xfrm6_protocol.c:132
ip6_protocol_deliver_rcu+0x372/0x1940 net/ipv6/ip6_input.c:394
ip6_input_finish+0x84/0x170 net/ipv6/ip6_input.c:434
NF_HOOK include/linux/netfilter.h:289 [inline]
ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:443
IPVS: ftp: loaded support on port[0] = 21
ip6_mc_input+0x514/0x11c0 net/ipv6/ip6_input.c:537
dst_input include/net/dst.h:450 [inline]
ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76
NF_HOOK include/linux/netfilter.h:289 [inline]
ipv6_rcv+0x115/0x640 net/ipv6/ip6_input.c:272
__netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4973
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5083
process_backlog+0x24e/0x7a0 net/core/dev.c:5923
napi_poll net/core/dev.c:6346 [inline]
net_rx_action+0x7fa/0x19b0 net/core/dev.c:6412
__do_softirq+0x308/0xb7e kernel/softirq.c:292
do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1027
</IRQ>
do_softirq.part.14+0x126/0x160 kernel/softirq.c:337
do_softirq+0x19/0x20 kernel/softirq.c:340
netif_rx_ni+0x521/0x860 net/core/dev.c:4569
dev_loopback_xmit+0x287/0x8c0 net/core/dev.c:3576
NF_HOOK include/linux/netfilter.h:289 [inline]
ip6_finish_output2+0x193a/0x2930 net/ipv6/ip6_output.c:84
ip6_fragment+0x2b06/0x3850 net/ipv6/ip6_output.c:727
ip6_finish_output+0x6b7/0xc50 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:278 [inline]
ip6_output+0x232/0x9d0 net/ipv6/ip6_output.c:171
dst_output include/net/dst.h:444 [inline]
ip6_local_out+0xc5/0x1b0 net/ipv6/output_core.c:176
ip6_send_skb+0xbc/0x340 net/ipv6/ip6_output.c:1727
ip6_push_pending_frames+0xc5/0xf0 net/ipv6/ip6_output.c:1747
rawv6_push_pending_frames net/ipv6/raw.c:615 [inline]
rawv6_sendmsg+0x3a3e/0x4b40 net/ipv6/raw.c:945
kobject: 'queues' (0000000089e6eea2): kobject_add_internal: parent: 'tunl0', set: '<NULL>'
kobject: 'queues' (0000000089e6eea2): kobject_uevent_env
inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
kobject: 'queues' (0000000089e6eea2): kobject_uevent_env: filter function caused the event to drop!
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:631
sock_write_iter+0x35e/0x5c0 net/socket.c:900
call_write_iter include/linux/fs.h:1857 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6b8/0x9f0 fs/read_write.c:487
kobject: 'rx-0' (00000000e2d902d9): kobject_add_internal: parent: 'queues', set: 'queues'
kobject: 'rx-0' (00000000e2d902d9): kobject_uevent_env
vfs_write+0x1fc/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
kobject: 'rx-0' (00000000e2d902d9): fill_kobj_path: path = '/devices/virtual/net/tunl0/queues/rx-0'
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
kobject: 'tx-0' (00000000443b70ac): kobject_add_internal: parent: 'queues', set: 'queues'
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457669
Code: fd b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9bd200bc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457669
RDX: 000000000000058f RSI: 00000000200033c0 RDI: 0000000000000003
kobject: 'tx-0' (00000000443b70ac): kobject_uevent_env
RBP: 000000000072bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9bd200c6d4
R13: 00000000004c2dcc R14: 00000000004da398 R15: 00000000ffffffff
Allocated by task 1304:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
__do_kmalloc_node mm/slab.c:3684 [inline]
__kmalloc_node_track_caller+0x50/0x70 mm/slab.c:3698
__kmalloc_reserve.isra.41+0x41/0xe0 net/core/skbuff.c:140
__alloc_skb+0x155/0x760 net/core/skbuff.c:208
kobject: 'tx-0' (00000000443b70ac): fill_kobj_path: path = '/devices/virtual/net/tunl0/queues/tx-0'
alloc_skb include/linux/skbuff.h:1011 [inline]
__ip6_append_data.isra.49+0x2f1a/0x3f50 net/ipv6/ip6_output.c:1450
ip6_append_data+0x1bc/0x2d0 net/ipv6/ip6_output.c:1619
rawv6_sendmsg+0x15ab/0x4b40 net/ipv6/raw.c:938
inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:631
___sys_sendmsg+0x7fd/0x930 net/socket.c:2116
__sys_sendmsg+0x11d/0x280 net/socket.c:2154
__do_sys_sendmsg net/socket.c:2163 [inline]
__se_sys_sendmsg net/socket.c:2161 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2161
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
kobject: 'gre0' (00000000cb1b2d7b): kobject_add_internal: parent: 'net', set: 'devices'
Freed by task 1304:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
skb_free_head+0x93/0xb0 net/core/skbuff.c:553
pskb_expand_head+0x3b2/0x10d0 net/core/skbuff.c:1498
__pskb_pull_tail+0x156/0x18a0 net/core/skbuff.c:1896
pskb_may_pull include/linux/skbuff.h:2188 [inline]
_decode_session6+0xd11/0x14d0 net/ipv6/xfrm6_policy.c:150
__xfrm_decode_session+0x71/0x140 net/xfrm/xfrm_policy.c:3272
kobject: 'gre0' (00000000cb1b2d7b): kobject_uevent_env
__xfrm_policy_check+0x380/0x2c40 net/xfrm/xfrm_policy.c:3322
__xfrm_policy_check2 include/net/xfrm.h:1170 [inline]
xfrm_policy_check include/net/xfrm.h:1175 [inline]
xfrm6_policy_check include/net/xfrm.h:1185 [inline]
vti6_rcv+0x4bd/0x8f3 net/ipv6/ip6_vti.c:316
xfrm6_ipcomp_rcv+0x1a5/0x3a0 net/ipv6/xfrm6_protocol.c:132
ip6_protocol_deliver_rcu+0x372/0x1940 net/ipv6/ip6_input.c:394
ip6_input_finish+0x84/0x170 net/ipv6/ip6_input.c:434
NF_HOOK include/linux/netfilter.h:289 [inline]
ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:443
ip6_mc_input+0x514/0x11c0 net/ipv6/ip6_input.c:537
dst_input include/net/dst.h:450 [inline]
ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76
NF_HOOK include/linux/netfilter.h:289 [inline]
ipv6_rcv+0x115/0x640 net/ipv6/ip6_input.c:272
__netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4973
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5083
process_backlog+0x24e/0x7a0 net/core/dev.c:5923
kobject: 'gre0' (00000000cb1b2d7b): fill_kobj_path: path = '/devices/virtual/net/gre0'
napi_poll net/core/dev.c:6346 [inline]
net_rx_action+0x7fa/0x19b0 net/core/dev.c:6412
__do_softirq+0x308/0xb7e kernel/softirq.c:292
The buggy address belongs to the object at ffff888191b8cac0
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 176 bytes inside of
512-byte region [ffff888191b8cac0, ffff888191b8ccc0)
The buggy address belongs to the page:
page:ffffea000646e300 count:1 mapcount:0 mapping:ffff8881da800940 index:0x0
flags: 0x2fffc0000000200(slab)
raw: 02fffc0000000200 ffffea0006eaaa48 ffffea00065356c8 ffff8881da800940
raw: 0000000000000000 ffff888191b8c0c0 0000000100000006 0000000000000000
page dumped because: kasan: bad access detected
kobject: 'queues' (000000005fd6226e): kobject_add_internal: parent: 'gre0', set: '<NULL>'
Memory state around the buggy address:
ffff888191b8ca00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888191b8ca80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff888191b8cb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888191b8cb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888191b8cc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path")
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces")
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Steffen Klassert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/ip6_tunnel.c | 1 +
net/ipv6/ip6_vti.c | 1 +
2 files changed, 2 insertions(+)
--- a/net/ipv6/ip6_tunnel.c
+++ b/net/ipv6/ip6_tunnel.c
@@ -901,6 +901,7 @@ static int ipxip6_rcv(struct sk_buff *sk
goto drop;
if (!xfrm6_policy_check(NULL, XFRM_POLICY_IN, skb))
goto drop;
+ ipv6h = ipv6_hdr(skb);
if (!ip6_tnl_rcv_ctl(t, &ipv6h->daddr, &ipv6h->saddr))
goto drop;
if (iptunnel_pull_header(skb, 0, tpi->proto, false))
--- a/net/ipv6/ip6_vti.c
+++ b/net/ipv6/ip6_vti.c
@@ -318,6 +318,7 @@ static int vti6_rcv(struct sk_buff *skb)
return 0;
}
+ ipv6h = ipv6_hdr(skb);
if (!ip6_tnl_rcv_ctl(t, &ipv6h->daddr, &ipv6h->saddr)) {
t->dev->stats.rx_dropped++;
rcu_read_unlock();
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Kunihiko Hayashi <[email protected]>
[ Upstream commit 8742beb50f2db903d3b6d69ddd81d67ce9914453 ]
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <[email protected]>
Signed-off-by: Kunihiko Hayashi <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/phy/phy_device.c | 7 ++-----
1 file changed, 2 insertions(+), 5 deletions(-)
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -164,11 +164,8 @@ static int mdio_bus_phy_restore(struct d
if (ret < 0)
return ret;
- /* The PHY needs to renegotiate. */
- phydev->link = 0;
- phydev->state = PHY_UP;
-
- phy_start_machine(phydev);
+ if (phydev->attached_dev && phydev->adjust_link)
+ phy_start_machine(phydev);
return 0;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tyrel Datwyler <[email protected]>
[ Upstream commit 756af9c642329d54f048bac2a62f829b391f6944 ]
Commit 33a48ab105a7 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec677 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec677 ("ibmveth: Add scatter-gather support")
Signed-off-by: Tyrel Datwyler <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/ibm/ibmveth.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
--- a/drivers/net/ethernet/ibm/ibmveth.c
+++ b/drivers/net/ethernet/ibm/ibmveth.c
@@ -1172,11 +1172,15 @@ out:
map_failed_frags:
last = i+1;
- for (i = 0; i < last; i++)
+ for (i = 1; i < last; i++)
dma_unmap_page(&adapter->vdev->dev, descs[i].fields.address,
descs[i].fields.flags_len & IBMVETH_BUF_LEN_MASK,
DMA_TO_DEVICE);
+ dma_unmap_single(&adapter->vdev->dev,
+ descs[0].fields.address,
+ descs[0].fields.flags_len & IBMVETH_BUF_LEN_MASK,
+ DMA_TO_DEVICE);
map_failed:
if (!firmware_has_feature(FW_FEATURE_CMO))
netdev_err(netdev, "tx: unable to map xmit buffer\n");
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: "Gustavo A. R. Silva" <[email protected]>
[ Upstream commit 69d2c86766da2ded2b70281f1bf242cb0d58a778 ]
vr.mifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.mifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/ip6mr.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/net/ipv6/ip6mr.c
+++ b/net/ipv6/ip6mr.c
@@ -52,6 +52,8 @@
#include <net/ip6_checksum.h>
#include <linux/netconf.h>
+#include <linux/nospec.h>
+
struct ip6mr_rule {
struct fib_rule common;
};
@@ -1831,6 +1833,7 @@ int ip6mr_ioctl(struct sock *sk, int cmd
return -EFAULT;
if (vr.mifi >= mrt->maxvif)
return -EINVAL;
+ vr.mifi = array_index_nospec(vr.mifi, mrt->maxvif);
read_lock(&mrt_lock);
vif = &mrt->vif_table[vr.mifi];
if (VIF_EXISTS(mrt, vr.mifi)) {
@@ -1905,6 +1908,7 @@ int ip6mr_compat_ioctl(struct sock *sk,
return -EFAULT;
if (vr.mifi >= mrt->maxvif)
return -EINVAL;
+ vr.mifi = array_index_nospec(vr.mifi, mrt->maxvif);
read_lock(&mrt_lock);
vif = &mrt->vif_table[vr.mifi];
if (VIF_EXISTS(mrt, vr.mifi)) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Deepa Dinamani <[email protected]>
[ Upstream commit 3a0ed3e9619738067214871e9cb826fa23b2ddb9 ]
Al Viro mentioned (Message-ID
<[email protected]>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a0c ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Signed-off-by: Deepa Dinamani <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/net/sock.h | 38 +++++++++++++++++++++++++++++++++++---
net/compat.c | 15 +++++++++------
net/core/sock.c | 15 ++++++++++-----
net/sunrpc/svcsock.c | 2 +-
4 files changed, 55 insertions(+), 15 deletions(-)
--- a/include/net/sock.h
+++ b/include/net/sock.h
@@ -298,6 +298,7 @@ struct sock_common {
* @sk_filter: socket filtering instructions
* @sk_timer: sock cleanup timer
* @sk_stamp: time stamp of last packet received
+ * @sk_stamp_seq: lock for accessing sk_stamp on 32 bit architectures only
* @sk_tsflags: SO_TIMESTAMPING socket options
* @sk_tskey: counter to disambiguate concurrent tstamp requests
* @sk_zckey: counter to order MSG_ZEROCOPY notifications
@@ -474,6 +475,9 @@ struct sock {
const struct cred *sk_peer_cred;
long sk_rcvtimeo;
ktime_t sk_stamp;
+#if BITS_PER_LONG==32
+ seqlock_t sk_stamp_seq;
+#endif
u16 sk_tsflags;
u8 sk_shutdown;
u32 sk_tskey;
@@ -2290,6 +2294,34 @@ static inline void sk_drops_add(struct s
atomic_add(segs, &sk->sk_drops);
}
+static inline ktime_t sock_read_timestamp(struct sock *sk)
+{
+#if BITS_PER_LONG==32
+ unsigned int seq;
+ ktime_t kt;
+
+ do {
+ seq = read_seqbegin(&sk->sk_stamp_seq);
+ kt = sk->sk_stamp;
+ } while (read_seqretry(&sk->sk_stamp_seq, seq));
+
+ return kt;
+#else
+ return sk->sk_stamp;
+#endif
+}
+
+static inline void sock_write_timestamp(struct sock *sk, ktime_t kt)
+{
+#if BITS_PER_LONG==32
+ write_seqlock(&sk->sk_stamp_seq);
+ sk->sk_stamp = kt;
+ write_sequnlock(&sk->sk_stamp_seq);
+#else
+ sk->sk_stamp = kt;
+#endif
+}
+
void __sock_recv_timestamp(struct msghdr *msg, struct sock *sk,
struct sk_buff *skb);
void __sock_recv_wifi_status(struct msghdr *msg, struct sock *sk,
@@ -2314,7 +2346,7 @@ sock_recv_timestamp(struct msghdr *msg,
(sk->sk_tsflags & SOF_TIMESTAMPING_RAW_HARDWARE)))
__sock_recv_timestamp(msg, sk, skb);
else
- sk->sk_stamp = kt;
+ sock_write_timestamp(sk, kt);
if (sock_flag(sk, SOCK_WIFI_STATUS) && skb->wifi_acked_valid)
__sock_recv_wifi_status(msg, sk, skb);
@@ -2335,9 +2367,9 @@ static inline void sock_recv_ts_and_drop
if (sk->sk_flags & FLAGS_TS_OR_DROPS || sk->sk_tsflags & TSFLAGS_ANY)
__sock_recv_ts_and_drops(msg, sk, skb);
else if (unlikely(sock_flag(sk, SOCK_TIMESTAMP)))
- sk->sk_stamp = skb->tstamp;
+ sock_write_timestamp(sk, skb->tstamp);
else if (unlikely(sk->sk_stamp == SK_DEFAULT_STAMP))
- sk->sk_stamp = 0;
+ sock_write_timestamp(sk, 0);
}
void __sock_tx_timestamp(__u16 tsflags, __u8 *tx_flags);
--- a/net/compat.c
+++ b/net/compat.c
@@ -467,12 +467,14 @@ int compat_sock_get_timestamp(struct soc
ctv = (struct compat_timeval __user *) userstamp;
err = -ENOENT;
sock_enable_timestamp(sk, SOCK_TIMESTAMP);
- tv = ktime_to_timeval(sk->sk_stamp);
+ tv = ktime_to_timeval(sock_read_timestamp(sk));
+
if (tv.tv_sec == -1)
return err;
if (tv.tv_sec == 0) {
- sk->sk_stamp = ktime_get_real();
- tv = ktime_to_timeval(sk->sk_stamp);
+ ktime_t kt = ktime_get_real();
+ sock_write_timestamp(sk, kt);
+ tv = ktime_to_timeval(kt);
}
err = 0;
if (put_user(tv.tv_sec, &ctv->tv_sec) ||
@@ -494,12 +496,13 @@ int compat_sock_get_timestampns(struct s
ctv = (struct compat_timespec __user *) userstamp;
err = -ENOENT;
sock_enable_timestamp(sk, SOCK_TIMESTAMP);
- ts = ktime_to_timespec(sk->sk_stamp);
+ ts = ktime_to_timespec(sock_read_timestamp(sk));
if (ts.tv_sec == -1)
return err;
if (ts.tv_sec == 0) {
- sk->sk_stamp = ktime_get_real();
- ts = ktime_to_timespec(sk->sk_stamp);
+ ktime_t kt = ktime_get_real();
+ sock_write_timestamp(sk, kt);
+ ts = ktime_to_timespec(kt);
}
err = 0;
if (put_user(ts.tv_sec, &ctv->tv_sec) ||
--- a/net/core/sock.c
+++ b/net/core/sock.c
@@ -2803,6 +2803,9 @@ void sock_init_data(struct socket *sock,
sk->sk_sndtimeo = MAX_SCHEDULE_TIMEOUT;
sk->sk_stamp = SK_DEFAULT_STAMP;
+#if BITS_PER_LONG==32
+ seqlock_init(&sk->sk_stamp_seq);
+#endif
atomic_set(&sk->sk_zckey, 0);
#ifdef CONFIG_NET_RX_BUSY_POLL
@@ -2902,12 +2905,13 @@ int sock_get_timestamp(struct sock *sk,
struct timeval tv;
sock_enable_timestamp(sk, SOCK_TIMESTAMP);
- tv = ktime_to_timeval(sk->sk_stamp);
+ tv = ktime_to_timeval(sock_read_timestamp(sk));
if (tv.tv_sec == -1)
return -ENOENT;
if (tv.tv_sec == 0) {
- sk->sk_stamp = ktime_get_real();
- tv = ktime_to_timeval(sk->sk_stamp);
+ ktime_t kt = ktime_get_real();
+ sock_write_timestamp(sk, kt);
+ tv = ktime_to_timeval(kt);
}
return copy_to_user(userstamp, &tv, sizeof(tv)) ? -EFAULT : 0;
}
@@ -2918,11 +2922,12 @@ int sock_get_timestampns(struct sock *sk
struct timespec ts;
sock_enable_timestamp(sk, SOCK_TIMESTAMP);
- ts = ktime_to_timespec(sk->sk_stamp);
+ ts = ktime_to_timespec(sock_read_timestamp(sk));
if (ts.tv_sec == -1)
return -ENOENT;
if (ts.tv_sec == 0) {
- sk->sk_stamp = ktime_get_real();
+ ktime_t kt = ktime_get_real();
+ sock_write_timestamp(sk, kt);
ts = ktime_to_timespec(sk->sk_stamp);
}
return copy_to_user(userstamp, &ts, sizeof(ts)) ? -EFAULT : 0;
--- a/net/sunrpc/svcsock.c
+++ b/net/sunrpc/svcsock.c
@@ -574,7 +574,7 @@ static int svc_udp_recvfrom(struct svc_r
/* Don't enable netstamp, sunrpc doesn't
need that much accuracy */
}
- svsk->sk_sk->sk_stamp = skb->tstamp;
+ sock_write_timestamp(svsk->sk_sk, skb->tstamp);
set_bit(XPT_DATA, &svsk->sk_xprt.xpt_flags); /* there may be more data... */
len = skb->len;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: "Gustavo A. R. Silva" <[email protected]>
[ Upstream commit 5648451e30a0d13d11796574919a359025d52cce ]
vr.vifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv4/ipmr.c:1616 ipmr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv4/ipmr.c:1690 ipmr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.vifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv4/ipmr.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/net/ipv4/ipmr.c
+++ b/net/ipv4/ipmr.c
@@ -69,6 +69,8 @@
#include <net/nexthop.h>
#include <net/switchdev.h>
+#include <linux/nospec.h>
+
struct ipmr_rule {
struct fib_rule common;
};
@@ -1612,6 +1614,7 @@ int ipmr_ioctl(struct sock *sk, int cmd,
return -EFAULT;
if (vr.vifi >= mrt->maxvif)
return -EINVAL;
+ vr.vifi = array_index_nospec(vr.vifi, mrt->maxvif);
read_lock(&mrt_lock);
vif = &mrt->vif_table[vr.vifi];
if (VIF_EXISTS(mrt, vr.vifi)) {
@@ -1686,6 +1689,7 @@ int ipmr_compat_ioctl(struct sock *sk, u
return -EFAULT;
if (vr.vifi >= mrt->maxvif)
return -EINVAL;
+ vr.vifi = array_index_nospec(vr.vifi, mrt->maxvif);
read_lock(&mrt_lock);
vif = &mrt->vif_table[vr.vifi];
if (VIF_EXISTS(mrt, vr.vifi)) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <[email protected]>
[ Upstream commit f0c928d878e7d01b613c9ae5c971a6b1e473a938 ]
Alexei reported use after frees in inet_diag_dump_icsk() [1]
Because we use refcount_set() when various sockets are setup and
inserted into ehash, we also need to make sure inet_diag_dump_icsk()
wont race with the refcount_set() operations.
Jonathan Lemon sent a patch changing net_twsk_hashdance() but
other spots would need risky changes.
Instead, fix inet_diag_dump_icsk() as this bug came with
linux-4.10 only.
[1] Quoting Alexei :
First something iterating over sockets finds already freed tw socket:
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 2 PID: 2738 at lib/refcount.c:153 refcount_inc+0x26/0x30
RIP: 0010:refcount_inc+0x26/0x30
RSP: 0018:ffffc90004c8fbc0 EFLAGS: 00010282
RAX: 000000000000002b RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88085ee9d680 RSI: ffff88085ee954c8 RDI: ffff88085ee954c8
RBP: ffff88010ecbd2c0 R08: 0000000000000000 R09: 000000000000174c
R10: ffffffff81e7c5a0 R11: 0000000000000000 R12: 0000000000000000
R13: ffff8806ba9bf210 R14: ffffffff82304600 R15: ffff88010ecbd328
FS: 00007f81f5a7d700(0000) GS:ffff88085ee80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f81e2a95000 CR3: 000000069b2eb006 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
inet_diag_dump_icsk+0x2b3/0x4e0 [inet_diag] // sock_hold(sk); in net/ipv4/inet_diag.c:1002
? kmalloc_large_node+0x37/0x70
? __kmalloc_node_track_caller+0x1cb/0x260
? __alloc_skb+0x72/0x1b0
? __kmalloc_reserve.isra.40+0x2e/0x80
__inet_diag_dump+0x3b/0x80 [inet_diag]
netlink_dump+0x116/0x2a0
netlink_recvmsg+0x205/0x3c0
sock_read_iter+0x89/0xd0
__vfs_read+0xf7/0x140
vfs_read+0x8a/0x140
SyS_read+0x3f/0xa0
do_syscall_64+0x5a/0x100
then a minute later twsk timer fires and hits two bad refcnts
for this freed socket:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 31 PID: 0 at lib/refcount.c:228 refcount_dec+0x2e/0x40
Modules linked in:
RIP: 0010:refcount_dec+0x2e/0x40
RSP: 0018:ffff88085f5c3ea8 EFLAGS: 00010296
RAX: 000000000000002c RBX: ffff88010ecbd2c0 RCX: 000000000000083f
RDX: 0000000000000000 RSI: 00000000000000f6 RDI: 000000000000003f
RBP: ffffc90003c77280 R08: 0000000000000000 R09: 00000000000017d3
R10: ffffffff81e7c5a0 R11: 0000000000000000 R12: ffffffff82ad2d80
R13: ffffffff8182de00 R14: ffff88085f5c3ef8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88085f5c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fbe42685250 CR3: 0000000002209001 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
inet_twsk_kill+0x9d/0xc0 // inet_twsk_bind_unhash(tw, hashinfo);
call_timer_fn+0x29/0x110
run_timer_softirq+0x36b/0x3a0
refcount_t: underflow; use-after-free.
WARNING: CPU: 31 PID: 0 at lib/refcount.c:187 refcount_sub_and_test+0x46/0x50
RIP: 0010:refcount_sub_and_test+0x46/0x50
RSP: 0018:ffff88085f5c3eb8 EFLAGS: 00010296
RAX: 0000000000000026 RBX: ffff88010ecbd2c0 RCX: 000000000000083f
RDX: 0000000000000000 RSI: 00000000000000f6 RDI: 000000000000003f
RBP: ffff88010ecbd358 R08: 0000000000000000 R09: 000000000000185b
R10: ffffffff81e7c5a0 R11: 0000000000000000 R12: ffff88010ecbd358
R13: ffffffff8182de00 R14: ffff88085f5c3ef8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88085f5c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fbe42685250 CR3: 0000000002209001 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
inet_twsk_put+0x12/0x20 // inet_twsk_put(tw);
call_timer_fn+0x29/0x110
run_timer_softirq+0x36b/0x3a0
Fixes: 67db3e4bfbc9 ("tcp: no longer hold ehash lock while calling tcp_get_info()")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: Alexei Starovoitov <[email protected]>
Cc: Jonathan Lemon <[email protected]>
Acked-by: Jonathan Lemon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv4/inet_diag.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/net/ipv4/inet_diag.c
+++ b/net/ipv4/inet_diag.c
@@ -998,7 +998,9 @@ next_chunk:
if (!inet_diag_bc_sk(bc, sk))
goto next_normal;
- sock_hold(sk);
+ if (!refcount_inc_not_zero(&sk->sk_refcnt))
+ goto next_normal;
+
num_arr[accum] = num;
sk_arr[accum] = sk;
if (++accum == SKARR_SZ)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit 15ef70e286176165d28b0b8a969b422561a68dfc ]
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc048a ("tipc: convert tipc reference table to use generic rhashtable")
Reported-by: Dmitry Vyukov <[email protected]>
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/socket.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
--- a/net/tipc/socket.c
+++ b/net/tipc/socket.c
@@ -2686,11 +2686,15 @@ void tipc_sk_reinit(struct net *net)
rhashtable_walk_start(&iter);
while ((tsk = rhashtable_walk_next(&iter)) && !IS_ERR(tsk)) {
- spin_lock_bh(&tsk->sk.sk_lock.slock);
+ sock_hold(&tsk->sk);
+ rhashtable_walk_stop(&iter);
+ lock_sock(&tsk->sk);
msg = &tsk->phdr;
msg_set_prevnode(msg, tipc_own_addr(net));
msg_set_orignode(msg, tipc_own_addr(net));
- spin_unlock_bh(&tsk->sk.sk_lock.slock);
+ release_sock(&tsk->sk);
+ rhashtable_walk_start(&iter);
+ sock_put(&tsk->sk);
}
rhashtable_walk_stop(&iter);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lorenzo Bianconi <[email protected]>
[ Upstream commit 8e1da73acded4751a93d4166458a7e640f37d26c ]
Add napi_disable routine in gro_cells_destroy since starting from
commit c42858eaf492 ("gro_cells: remove spinlock protecting receive
queues") gro_cell_poll and gro_cells_destroy can run concurrently on
napi_skbs list producing a kernel Oops if the tunnel interface is
removed while gro_cell_poll is running. The following Oops has been
triggered removing a vxlan device while the interface is receiving
traffic
[ 5628.948853] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 5628.949981] PGD 0 P4D 0
[ 5628.950308] Oops: 0002 [#1] SMP PTI
[ 5628.950748] CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 4.20.0-rc6+ #41
[ 5628.952940] RIP: 0010:gro_cell_poll+0x49/0x80
[ 5628.955615] RSP: 0018:ffffc9000004fdd8 EFLAGS: 00010202
[ 5628.956250] RAX: 0000000000000000 RBX: ffffe8ffffc08150 RCX: 0000000000000000
[ 5628.957102] RDX: 0000000000000000 RSI: ffff88802356bf00 RDI: ffffe8ffffc08150
[ 5628.957940] RBP: 0000000000000026 R08: 0000000000000000 R09: 0000000000000000
[ 5628.958803] R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000040
[ 5628.959661] R13: ffffe8ffffc08100 R14: 0000000000000000 R15: 0000000000000040
[ 5628.960682] FS: 0000000000000000(0000) GS:ffff88803ea00000(0000) knlGS:0000000000000000
[ 5628.961616] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5628.962359] CR2: 0000000000000008 CR3: 000000000221c000 CR4: 00000000000006b0
[ 5628.963188] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 5628.964034] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 5628.964871] Call Trace:
[ 5628.965179] net_rx_action+0xf0/0x380
[ 5628.965637] __do_softirq+0xc7/0x431
[ 5628.966510] run_ksoftirqd+0x24/0x30
[ 5628.966957] smpboot_thread_fn+0xc5/0x160
[ 5628.967436] kthread+0x113/0x130
[ 5628.968283] ret_from_fork+0x3a/0x50
[ 5628.968721] Modules linked in:
[ 5628.969099] CR2: 0000000000000008
[ 5628.969510] ---[ end trace 9d9dedc7181661fe ]---
[ 5628.970073] RIP: 0010:gro_cell_poll+0x49/0x80
[ 5628.972965] RSP: 0018:ffffc9000004fdd8 EFLAGS: 00010202
[ 5628.973611] RAX: 0000000000000000 RBX: ffffe8ffffc08150 RCX: 0000000000000000
[ 5628.974504] RDX: 0000000000000000 RSI: ffff88802356bf00 RDI: ffffe8ffffc08150
[ 5628.975462] RBP: 0000000000000026 R08: 0000000000000000 R09: 0000000000000000
[ 5628.976413] R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000040
[ 5628.977375] R13: ffffe8ffffc08100 R14: 0000000000000000 R15: 0000000000000040
[ 5628.978296] FS: 0000000000000000(0000) GS:ffff88803ea00000(0000) knlGS:0000000000000000
[ 5628.979327] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5628.980044] CR2: 0000000000000008 CR3: 000000000221c000 CR4: 00000000000006b0
[ 5628.980929] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 5628.981736] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 5628.982409] Kernel panic - not syncing: Fatal exception in interrupt
[ 5628.983307] Kernel Offset: disabled
Fixes: c42858eaf492 ("gro_cells: remove spinlock protecting receive queues")
Signed-off-by: Lorenzo Bianconi <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/core/gro_cells.c | 1 +
1 file changed, 1 insertion(+)
--- a/net/core/gro_cells.c
+++ b/net/core/gro_cells.c
@@ -84,6 +84,7 @@ void gro_cells_destroy(struct gro_cells
for_each_possible_cpu(i) {
struct gro_cell *cell = per_cpu_ptr(gcells->cells, i);
+ napi_disable(&cell->napi);
netif_napi_del(&cell->napi);
__skb_queue_purge(&cell->napi_skbs);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Xin Long <[email protected]>
[ Upstream commit 4a2eb0c37b4759416996fbb4c45b932500cf06d3 ]
syzbot reported a kernel-infoleak, which is caused by an uninitialized
field(sin6_flowinfo) of addr->a.v6 in sctp_inet6addr_event().
The call trace is as below:
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x19a/0x230 lib/usercopy.c:33
CPU: 1 PID: 8164 Comm: syz-executor2 Not tainted 4.20.0-rc3+ #95
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x32d/0x480 lib/dump_stack.c:113
kmsan_report+0x12c/0x290 mm/kmsan/kmsan.c:683
kmsan_internal_check_memory+0x32a/0xa50 mm/kmsan/kmsan.c:743
kmsan_copy_to_user+0x78/0xd0 mm/kmsan/kmsan_hooks.c:634
_copy_to_user+0x19a/0x230 lib/usercopy.c:33
copy_to_user include/linux/uaccess.h:183 [inline]
sctp_getsockopt_local_addrs net/sctp/socket.c:5998 [inline]
sctp_getsockopt+0x15248/0x186f0 net/sctp/socket.c:7477
sock_common_getsockopt+0x13f/0x180 net/core/sock.c:2937
__sys_getsockopt+0x489/0x550 net/socket.c:1939
__do_sys_getsockopt net/socket.c:1950 [inline]
__se_sys_getsockopt+0xe1/0x100 net/socket.c:1947
__x64_sys_getsockopt+0x62/0x80 net/socket.c:1947
do_syscall_64+0xcf/0x110 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
sin6_flowinfo is not really used by SCTP, so it will be fixed by simply
setting it to 0.
The issue exists since very beginning.
Thanks Alexander for the reproducer provided.
Reported-by: [email protected]
Signed-off-by: Xin Long <[email protected]>
Acked-by: Marcelo Ricardo Leitner <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/sctp/ipv6.c | 1 +
1 file changed, 1 insertion(+)
--- a/net/sctp/ipv6.c
+++ b/net/sctp/ipv6.c
@@ -101,6 +101,7 @@ static int sctp_inet6addr_event(struct n
if (addr) {
addr->a.v6.sin6_family = AF_INET6;
addr->a.v6.sin6_port = 0;
+ addr->a.v6.sin6_flowinfo = 0;
addr->a.v6.sin6_addr = ifa->addr;
addr->a.v6.sin6_scope_id = ifa->idev->dev->ifindex;
addr->valid = 1;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jorgen Hansen <[email protected]>
[ Upstream commit a915b982d8f5e4295f64b8dd37ce753874867e88 ]
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Reviewed-by: Adit Ranadive <[email protected]>
Reviewed-by: Vishnu Dasa <[email protected]>
Signed-off-by: Jorgen Hansen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/vmw_vsock/vmci_transport.c | 67 ++++++++++++++++++++++++++++++-----------
1 file changed, 50 insertions(+), 17 deletions(-)
--- a/net/vmw_vsock/vmci_transport.c
+++ b/net/vmw_vsock/vmci_transport.c
@@ -264,6 +264,31 @@ vmci_transport_send_control_pkt_bh(struc
}
static int
+vmci_transport_alloc_send_control_pkt(struct sockaddr_vm *src,
+ struct sockaddr_vm *dst,
+ enum vmci_transport_packet_type type,
+ u64 size,
+ u64 mode,
+ struct vmci_transport_waiting_info *wait,
+ u16 proto,
+ struct vmci_handle handle)
+{
+ struct vmci_transport_packet *pkt;
+ int err;
+
+ pkt = kmalloc(sizeof(*pkt), GFP_KERNEL);
+ if (!pkt)
+ return -ENOMEM;
+
+ err = __vmci_transport_send_control_pkt(pkt, src, dst, type, size,
+ mode, wait, proto, handle,
+ true);
+ kfree(pkt);
+
+ return err;
+}
+
+static int
vmci_transport_send_control_pkt(struct sock *sk,
enum vmci_transport_packet_type type,
u64 size,
@@ -272,9 +297,7 @@ vmci_transport_send_control_pkt(struct s
u16 proto,
struct vmci_handle handle)
{
- struct vmci_transport_packet *pkt;
struct vsock_sock *vsk;
- int err;
vsk = vsock_sk(sk);
@@ -284,17 +307,10 @@ vmci_transport_send_control_pkt(struct s
if (!vsock_addr_bound(&vsk->remote_addr))
return -EINVAL;
- pkt = kmalloc(sizeof(*pkt), GFP_KERNEL);
- if (!pkt)
- return -ENOMEM;
-
- err = __vmci_transport_send_control_pkt(pkt, &vsk->local_addr,
- &vsk->remote_addr, type, size,
- mode, wait, proto, handle,
- true);
- kfree(pkt);
-
- return err;
+ return vmci_transport_alloc_send_control_pkt(&vsk->local_addr,
+ &vsk->remote_addr,
+ type, size, mode,
+ wait, proto, handle);
}
static int vmci_transport_send_reset_bh(struct sockaddr_vm *dst,
@@ -312,12 +328,29 @@ static int vmci_transport_send_reset_bh(
static int vmci_transport_send_reset(struct sock *sk,
struct vmci_transport_packet *pkt)
{
+ struct sockaddr_vm *dst_ptr;
+ struct sockaddr_vm dst;
+ struct vsock_sock *vsk;
+
if (pkt->type == VMCI_TRANSPORT_PACKET_TYPE_RST)
return 0;
- return vmci_transport_send_control_pkt(sk,
- VMCI_TRANSPORT_PACKET_TYPE_RST,
- 0, 0, NULL, VSOCK_PROTO_INVALID,
- VMCI_INVALID_HANDLE);
+
+ vsk = vsock_sk(sk);
+
+ if (!vsock_addr_bound(&vsk->local_addr))
+ return -EINVAL;
+
+ if (vsock_addr_bound(&vsk->remote_addr)) {
+ dst_ptr = &vsk->remote_addr;
+ } else {
+ vsock_addr_init(&dst, pkt->dg.src.context,
+ pkt->src_port);
+ dst_ptr = &dst;
+ }
+ return vmci_transport_alloc_send_control_pkt(&vsk->local_addr, dst_ptr,
+ VMCI_TRANSPORT_PACKET_TYPE_RST,
+ 0, 0, NULL, VSOCK_PROTO_INVALID,
+ VMCI_INVALID_HANDLE);
}
static int vmci_transport_send_negotiate(struct sock *sk, size_t size)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Juergen Gross <[email protected]>
[ Upstream commit d81c5054a5d1d4999c7cdead7636b6cd4af83d36 ]
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/xen-netfront.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/xen-netfront.c
+++ b/drivers/net/xen-netfront.c
@@ -905,7 +905,7 @@ static RING_IDX xennet_fill_frags(struct
if (skb_shinfo(skb)->nr_frags == MAX_SKB_FRAGS) {
unsigned int pull_to = NETFRONT_SKB_CB(skb)->pull_to;
- BUG_ON(pull_to <= skb_headlen(skb));
+ BUG_ON(pull_to < skb_headlen(skb));
__pskb_pull_tail(skb, pull_to - skb_headlen(skb));
}
if (unlikely(skb_shinfo(skb)->nr_frags >= MAX_SKB_FRAGS)) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit 3c6306d44082ef007a258ae1b86ea58e6974ee3f ]
Similar to commit 143ece654f9f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163dbb6 ("tipc: introduce communication groups")
Reported-and-tested-by: [email protected]
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/socket.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
--- a/net/tipc/socket.c
+++ b/net/tipc/socket.c
@@ -1007,7 +1007,7 @@ static int tipc_send_group_bcast(struct
struct sock *sk = sock->sk;
struct net *net = sock_net(sk);
struct tipc_sock *tsk = tipc_sk(sk);
- struct tipc_nlist *dsts = tipc_group_dests(tsk->group);
+ struct tipc_nlist *dsts;
struct tipc_mc_method *method = &tsk->mc_method;
bool ack = method->mandatory && method->rcast;
int blks = tsk_blocks(MCAST_H_SIZE + dlen);
@@ -1016,9 +1016,6 @@ static int tipc_send_group_bcast(struct
struct sk_buff_head pkts;
int rc = -EHOSTUNREACH;
- if (!dsts->local && !dsts->remote)
- return -EHOSTUNREACH;
-
/* Block or return if any destination link or member is congested */
rc = tipc_wait_for_cond(sock, &timeout,
!tsk->cong_link_cnt && tsk->group &&
@@ -1026,6 +1023,10 @@ static int tipc_send_group_bcast(struct
if (unlikely(rc))
return rc;
+ dsts = tipc_group_dests(tsk->group);
+ if (!dsts->local && !dsts->remote)
+ return -EHOSTUNREACH;
+
/* Complete message header */
if (dest) {
msg_set_type(hdr, TIPC_GRP_MCAST_MSG);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Willem de Bruijn <[email protected]>
[ Upstream commit 40c3ff6d5e0809505a067dd423c110c5658c478c ]
Packet sockets may call dev_header_parse with NULL daddr. Make
lowpan_header_ops.create fail.
Fixes: 87a93e4eceb4 ("ieee802154: change needed headroom/tailroom")
Signed-off-by: Willem de Bruijn <[email protected]>
Acked-by: Alexander Aring <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ieee802154/6lowpan/tx.c | 3 +++
1 file changed, 3 insertions(+)
--- a/net/ieee802154/6lowpan/tx.c
+++ b/net/ieee802154/6lowpan/tx.c
@@ -48,6 +48,9 @@ int lowpan_header_create(struct sk_buff
const struct ipv6hdr *hdr = ipv6_hdr(skb);
struct neighbour *n;
+ if (!daddr)
+ return -EINVAL;
+
/* TODO:
* if this package isn't ipv6 one, where should it be routed?
*/
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Pieter Jansen van Vuuren <[email protected]>
[ Upstream commit 290974d434783624c13a9530a23c45f9c5ffe018 ]
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfca5 ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <[email protected]>
Reviewed-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/netronome/nfp/flower/offload.c | 28 +++++++++++++++-----
1 file changed, 22 insertions(+), 6 deletions(-)
--- a/drivers/net/ethernet/netronome/nfp/flower/offload.c
+++ b/drivers/net/ethernet/netronome/nfp/flower/offload.c
@@ -375,13 +375,29 @@ nfp_flower_calculate_key_layers(struct n
!(tcp_flags & (TCPHDR_FIN | TCPHDR_SYN | TCPHDR_RST)))
return -EOPNOTSUPP;
- /* We need to store TCP flags in the IPv4 key space, thus
- * we need to ensure we include a IPv4 key layer if we have
- * not done so already.
+ /* We need to store TCP flags in the either the IPv4 or IPv6 key
+ * space, thus we need to ensure we include a IPv4/IPv6 key
+ * layer if we have not done so already.
*/
- if (!(key_layer & NFP_FLOWER_LAYER_IPV4)) {
- key_layer |= NFP_FLOWER_LAYER_IPV4;
- key_size += sizeof(struct nfp_flower_ipv4);
+ if (!key_basic)
+ return -EOPNOTSUPP;
+
+ if (!(key_layer & NFP_FLOWER_LAYER_IPV4) &&
+ !(key_layer & NFP_FLOWER_LAYER_IPV6)) {
+ switch (key_basic->n_proto) {
+ case cpu_to_be16(ETH_P_IP):
+ key_layer |= NFP_FLOWER_LAYER_IPV4;
+ key_size += sizeof(struct nfp_flower_ipv4);
+ break;
+
+ case cpu_to_be16(ETH_P_IPV6):
+ key_layer |= NFP_FLOWER_LAYER_IPV6;
+ key_size += sizeof(struct nfp_flower_ipv6);
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
}
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Christophe JAILLET <[email protected]>
[ Upstream commit 178fe94405bffbd1acd83b6ff3b40211185ae9c9 ]
'ipv6_find_idev()' returns NULL on error, not an error pointer.
Update the test accordingly and return -ENOBUFS, as already done in
'addrconf_add_dev()', if NULL is returned.
Fixes: ("ipv6: allow userspace to add IFA_F_OPTIMISTIC addresses")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/addrconf.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/net/ipv6/addrconf.c
+++ b/net/ipv6/addrconf.c
@@ -4711,8 +4711,8 @@ inet6_rtm_newaddr(struct sk_buff *skb, s
IFA_F_MCAUTOJOIN | IFA_F_OPTIMISTIC;
idev = ipv6_find_idev(dev);
- if (IS_ERR(idev))
- return PTR_ERR(idev);
+ if (!idev)
+ return -ENOBUFS;
if (!ipv6_allow_optimistic_dad(net, idev))
cfg.ifa_flags &= ~IFA_F_OPTIMISTIC;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tal Gilboa <[email protected]>
[ Upstream commit fa2bf86bab4bbc61e5678a42a14e40075093a98f ]
TXQ SQ closure is followed by closing the corresponding CQ. A pending
DIM work would try to modify the now non-existing CQ.
This would trigger an error:
[85535.835926] mlx5_core 0000:af:00.0: mlx5_cmd_check:769:(pid 124399):
MODIFY_CQ(0x403) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1d7771)
Fix by making sure to cancel any pending DIM work before destroying the SQ.
Fixes: cbce4f444798 ("net/mlx5e: Enable adaptive-TX moderation")
Signed-off-by: Tal Gilboa <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -1383,6 +1383,7 @@ static void mlx5e_close_txqsq(struct mlx
struct mlx5_core_dev *mdev = c->mdev;
struct mlx5_rate_limit rl = {0};
+ cancel_work_sync(&sq->dim.work);
mlx5e_destroy_sq(mdev, sq->sqn);
if (sq->rate_limit) {
rl.rate = sq->rate_limit;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Antoine Tenart <[email protected]>
[ Upstream commit 1b451fb2051b464b9758c09a3492104403252e2b ]
The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.
Fixes: d97c9f4ab000 ("net: mvpp2: 1000baseX support")
Reported-by: Russell King <[email protected]>
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4293,6 +4293,7 @@ static void mvpp2_phylink_validate(struc
case PHY_INTERFACE_MODE_XAUI:
case PHY_INTERFACE_MODE_NA:
if (port->gop_id == 0) {
+ phylink_set(mask, 10000baseT_Full);
phylink_set(mask, 10000baseCR_Full);
phylink_set(mask, 10000baseSR_Full);
phylink_set(mask, 10000baseLR_Full);
@@ -4310,7 +4311,6 @@ static void mvpp2_phylink_validate(struc
phylink_set(mask, 10baseT_Full);
phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);
- phylink_set(mask, 10000baseT_Full);
/* Fall-through */
case PHY_INTERFACE_MODE_1000BASEX:
case PHY_INTERFACE_MODE_2500BASEX:
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Davide Caratti <[email protected]>
[ Upstream commit e2c4cf7f98a519eb4d95532bfa06bcaf3562fed5 ]
Herton reports the following error when building a userspace program that
includes net_stamp.h:
In file included from foo.c:2:
/usr/include/linux/net_tstamp.h:158:2: error: unknown type name
‘clockid_t’
clockid_t clockid; /* reference clockid */
^~~~~~~~~
Fix it by using __kernel_clockid_t in place of clockid_t.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Cc: Timothy Redaelli <[email protected]>
Reported-by: Herton R. Krzesinski <[email protected]>
Signed-off-by: Davide Caratti <[email protected]>
Tested-by: Paolo Abeni <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/uapi/linux/net_tstamp.h | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/include/uapi/linux/net_tstamp.h
+++ b/include/uapi/linux/net_tstamp.h
@@ -155,8 +155,8 @@ enum txtime_flags {
};
struct sock_txtime {
- clockid_t clockid; /* reference clockid */
- __u32 flags; /* as defined by enum txtime_flags */
+ __kernel_clockid_t clockid;/* reference clockid */
+ __u32 flags; /* as defined by enum txtime_flags */
};
#endif /* _NET_TIMESTAMPING_H */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Herbert Xu <[email protected]>
[ Upstream commit d15f5ac8deea936d3adf629421a66a88b42b8a2f ]
It was reported that IPsec would crash when it encounters an IPv6
reassembled packet because skb->sk is non-zero and not a valid
pointer.
This is because skb->sk is now a union with ip_defrag_offset.
This patch fixes this by resetting skb->sk when exiting from
the reassembly code.
Reported-by: Xiumei Mu <[email protected]>
Fixes: 219badfaade9 ("ipv6: frags: get rid of ip6frag_skb_cb/...")
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/reassembly.c | 1 +
1 file changed, 1 insertion(+)
--- a/net/ipv6/reassembly.c
+++ b/net/ipv6/reassembly.c
@@ -384,6 +384,7 @@ static int ip6_frag_reasm(struct frag_qu
if (skb_try_coalesce(head, fp, &headstolen, &delta)) {
kfree_skb_partial(fp, headstolen);
} else {
+ fp->sk = NULL;
if (!skb_shinfo(head)->frag_list)
skb_shinfo(head)->frag_list = fp;
head->data_len += fp->len;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sudarsana Reddy Kalluru <[email protected]>
[ Upstream commit c3db8d531045774aeee6e0f731ab15b0c450de45 ]
The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.
Fixes: cac6f691546b ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/qlogic/qed/qed_hsi.h | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/net/ethernet/qlogic/qed/qed_hsi.h
+++ b/drivers/net/ethernet/qlogic/qed/qed_hsi.h
@@ -12669,8 +12669,9 @@ enum MFW_DRV_MSG_TYPE {
MFW_DRV_MSG_BW_UPDATE10,
MFW_DRV_MSG_TRANSCEIVER_STATE_CHANGE,
MFW_DRV_MSG_BW_UPDATE11,
- MFW_DRV_MSG_OEM_CFG_UPDATE,
+ MFW_DRV_MSG_RESERVED,
MFW_DRV_MSG_GET_TLV_REQ,
+ MFW_DRV_MSG_OEM_CFG_UPDATE,
MFW_DRV_MSG_MAX
};
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Terin Stock <[email protected]>
commit 6ed30a7d8ec29d3aba46e47aa8b4a44f077dda4e upstream.
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.
A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.
This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.
Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).
<idle>-0 [000] ..s. 1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
<idle>-0 [000] ..s. 1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977
After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.
<idle>-0 [000] d.h. 1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
<idle>-0 [000] d.h. 1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002
The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.
Fixes: 38d2b5fb75c1 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <[email protected]>
Reviewed-by: Douglas Anderson <[email protected]>
Acked-by: Minas Harutyunyan <[email protected]>
Signed-off-by: Terin Stock <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/dwc2/hcd.h | 2 +-
drivers/usb/dwc2/hcd_queue.c | 19 ++++++++++++-------
2 files changed, 13 insertions(+), 8 deletions(-)
--- a/drivers/usb/dwc2/hcd.h
+++ b/drivers/usb/dwc2/hcd.h
@@ -366,7 +366,7 @@ struct dwc2_qh {
u32 desc_list_sz;
u32 *n_bytes;
struct timer_list unreserve_timer;
- struct timer_list wait_timer;
+ struct hrtimer wait_timer;
struct dwc2_tt *dwc_tt;
int ttport;
unsigned tt_buffer_dirty:1;
--- a/drivers/usb/dwc2/hcd_queue.c
+++ b/drivers/usb/dwc2/hcd_queue.c
@@ -59,7 +59,7 @@
#define DWC2_UNRESERVE_DELAY (msecs_to_jiffies(5))
/* If we get a NAK, wait this long before retrying */
-#define DWC2_RETRY_WAIT_DELAY (msecs_to_jiffies(1))
+#define DWC2_RETRY_WAIT_DELAY 1*1E6L
/**
* dwc2_periodic_channel_available() - Checks that a channel is available for a
@@ -1464,10 +1464,12 @@ static void dwc2_deschedule_periodic(str
* qh back to the "inactive" list, then queues transactions.
*
* @t: Pointer to wait_timer in a qh.
+ *
+ * Return: HRTIMER_NORESTART to not automatically restart this timer.
*/
-static void dwc2_wait_timer_fn(struct timer_list *t)
+static enum hrtimer_restart dwc2_wait_timer_fn(struct hrtimer *t)
{
- struct dwc2_qh *qh = from_timer(qh, t, wait_timer);
+ struct dwc2_qh *qh = container_of(t, struct dwc2_qh, wait_timer);
struct dwc2_hsotg *hsotg = qh->hsotg;
unsigned long flags;
@@ -1491,6 +1493,7 @@ static void dwc2_wait_timer_fn(struct ti
}
spin_unlock_irqrestore(&hsotg->lock, flags);
+ return HRTIMER_NORESTART;
}
/**
@@ -1521,7 +1524,8 @@ static void dwc2_qh_init(struct dwc2_hso
/* Initialize QH */
qh->hsotg = hsotg;
timer_setup(&qh->unreserve_timer, dwc2_unreserve_timer_fn, 0);
- timer_setup(&qh->wait_timer, dwc2_wait_timer_fn, 0);
+ hrtimer_init(&qh->wait_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ qh->wait_timer.function = &dwc2_wait_timer_fn;
qh->ep_type = ep_type;
qh->ep_is_in = ep_is_in;
@@ -1690,7 +1694,7 @@ void dwc2_hcd_qh_free(struct dwc2_hsotg
* won't do anything anyway, but we want it to finish before we free
* memory.
*/
- del_timer_sync(&qh->wait_timer);
+ hrtimer_cancel(&qh->wait_timer);
dwc2_host_put_tt_info(hsotg, qh->dwc_tt);
@@ -1716,6 +1720,7 @@ int dwc2_hcd_qh_add(struct dwc2_hsotg *h
{
int status;
u32 intr_mask;
+ ktime_t delay;
if (dbg_qh(qh))
dev_vdbg(hsotg->dev, "%s()\n", __func__);
@@ -1734,8 +1739,8 @@ int dwc2_hcd_qh_add(struct dwc2_hsotg *h
list_add_tail(&qh->qh_list_entry,
&hsotg->non_periodic_sched_waiting);
qh->wait_timer_cancel = false;
- mod_timer(&qh->wait_timer,
- jiffies + DWC2_RETRY_WAIT_DELAY + 1);
+ delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
+ hrtimer_start(&qh->wait_timer, delay, HRTIMER_MODE_REL);
} else {
list_add_tail(&qh->qh_list_entry,
&hsotg->non_periodic_sched_inactive);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Heiner Kallweit <[email protected]>
[ Upstream commit 3bd8264511035dc97c902f03fa9f1d07f95f8f62 ]
In rtl8169_runtime_resume() we configure WoL but don't set the device
to wakeup-enabled. This prevents PME generation once the cable is
re-plugged. Fix this by moving the call to device_set_wakeup_enable()
to __rtl8169_set_wol().
Fixes: 433f9d0ddcc6 ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/realtek/r8169.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/net/ethernet/realtek/r8169.c
+++ b/drivers/net/ethernet/realtek/r8169.c
@@ -1528,6 +1528,8 @@ static void __rtl8169_set_wol(struct rtl
}
RTL_W8(tp, Cfg9346, Cfg9346_Lock);
+
+ device_set_wakeup_enable(tp_to_dev(tp), wolopts);
}
static int rtl8169_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
@@ -1549,8 +1551,6 @@ static int rtl8169_set_wol(struct net_de
rtl_unlock_work(tp);
- device_set_wakeup_enable(d, tp->saved_wolopts);
-
pm_runtime_put_noidle(d);
return 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michael J. Ruhl <[email protected]>
commit dbc2970caef74e8ff41923d302aa6fb5a4812d0e upstream.
An incorrect sge sizing in the HFI PIO path will cause an OOPs similar to
this:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [] hfi1_verbs_send_pio+0x3d8/0x530 [hfi1]
PGD 0
Oops: 0000 1 SMP
Call Trace:
? hfi1_verbs_send_dma+0xad0/0xad0 [hfi1]
hfi1_verbs_send+0xdf/0x250 [hfi1]
? make_rc_ack+0xa80/0xa80 [hfi1]
hfi1_do_send+0x192/0x430 [hfi1]
hfi1_do_send_from_rvt+0x10/0x20 [hfi1]
rvt_post_send+0x369/0x820 [rdmavt]
ib_uverbs_post_send+0x317/0x570 [ib_uverbs]
ib_uverbs_write+0x26f/0x420 [ib_uverbs]
? security_file_permission+0x21/0xa0
vfs_write+0xbd/0x1e0
? mntput+0x24/0x40
SyS_write+0x7f/0xe0
system_call_fastpath+0x16/0x1b
Fix by adding the missing sizing check to correctly determine the sge
length.
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Michael J. Ruhl <[email protected]>
Signed-off-by: Dennis Dalessandro <[email protected]>
Signed-off-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/infiniband/hw/hfi1/verbs.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/infiniband/hw/hfi1/verbs.c
+++ b/drivers/infiniband/hw/hfi1/verbs.c
@@ -1141,6 +1141,8 @@ int hfi1_verbs_send_pio(struct rvt_qp *q
if (slen > len)
slen = len;
+ if (slen > ss->sge.sge_length)
+ slen = ss->sge.sge_length;
rvt_update_sge(ss, slen, false);
seg_pio_copy_mid(pbuf, addr, slen);
len -= slen;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Moshe Shemesh <[email protected]>
[ Upstream commit e1c15b62b7015119d3e5915cd2ae3b89d59c2576 ]
Add check of MPWQE stride size is within range supported by HW. In case
calculated MPWQE stride size exceed range, linear SKB can't be used and
we should use non linear MPWQE instead.
Fixes: 619a8f2a42f1 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -128,6 +128,8 @@ static bool mlx5e_rx_is_linear_skb(struc
return !params->lro_en && frag_sz <= PAGE_SIZE;
}
+#define MLX5_MAX_MPWQE_LOG_WQE_STRIDE_SZ ((BIT(__mlx5_bit_sz(wq, log_wqe_stride_size)) - 1) + \
+ MLX5_MPWQE_LOG_STRIDE_SZ_BASE)
static bool mlx5e_rx_mpwqe_is_linear_skb(struct mlx5_core_dev *mdev,
struct mlx5e_params *params)
{
@@ -138,6 +140,9 @@ static bool mlx5e_rx_mpwqe_is_linear_skb
if (!mlx5e_rx_is_linear_skb(mdev, params))
return false;
+ if (order_base_2(frag_sz) > MLX5_MAX_MPWQE_LOG_WQE_STRIDE_SZ)
+ return false;
+
if (MLX5_CAP_GEN(mdev, ext_stride_num_range))
return true;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Takashi Sakamoto <[email protected]>
commit 5ef108c53e6efd695e32aad969638ccbc35b4be9 upstream.
An initial commit to add tracepoints for packets without CIP headers
uses different print formats for added tracepoints. However this is not
convenient for users/developers to prepare debug tools.
This commit uses the same format for the two tracepoints.
Cc: <[email protected]> # v4.12+
Fixes: b164d2fd6e49 ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/firewire/amdtp-stream-trace.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/sound/firewire/amdtp-stream-trace.h
+++ b/sound/firewire/amdtp-stream-trace.h
@@ -131,7 +131,7 @@ TRACE_EVENT(in_packet_without_header,
__entry->index = index;
),
TP_printk(
- "%02u %04u %04x %04x %02d %03u %3u %3u %02u %01u %02u",
+ "%02u %04u %04x %04x %02d %03u %02u %03u %02u %01u %02u",
__entry->second,
__entry->cycle,
__entry->src,
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: "Gustavo A. R. Silva" <[email protected]>
[ Upstream commit d686026b1e6ed4ea27d630d8f54f9a694db088b2 ]
protocol is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/phonet/af_phonet.c:48 phonet_proto_get() warn: potential spectre issue 'proto_tab' [w] (local cap)
Fix this by sanitizing protocol before using it to index proto_tab.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/phonet/af_phonet.c | 3 +++
1 file changed, 3 insertions(+)
--- a/net/phonet/af_phonet.c
+++ b/net/phonet/af_phonet.c
@@ -34,6 +34,8 @@
#include <net/phonet/phonet.h>
#include <net/phonet/pn_dev.h>
+#include <linux/nospec.h>
+
/* Transport protocol registration */
static const struct phonet_protocol *proto_tab[PHONET_NPROTO] __read_mostly;
@@ -43,6 +45,7 @@ static const struct phonet_protocol *pho
if (protocol >= PHONET_NPROTO)
return NULL;
+ protocol = array_index_nospec(protocol, PHONET_NPROTO);
rcu_read_lock();
pp = rcu_dereference(proto_tab[protocol]);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tariq Toukan <[email protected]>
[ Upstream commit bfc698254ba97b3e3e4ebbfae0ffa1f7e2fa0717 ]
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Tariq Toukan <[email protected]>
Reviewed-by: Eran Ben Elisha <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_rx.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rx.c
@@ -1150,7 +1150,7 @@ mpwrq_cqe_out:
int mlx5e_poll_rx_cq(struct mlx5e_cq *cq, int budget)
{
struct mlx5e_rq *rq = container_of(cq, struct mlx5e_rq, cq);
- struct mlx5e_xdpsq *xdpsq;
+ struct mlx5e_xdpsq *xdpsq = &rq->xdpsq;
struct mlx5_cqe64 *cqe;
int work_done = 0;
@@ -1161,10 +1161,11 @@ int mlx5e_poll_rx_cq(struct mlx5e_cq *cq
work_done += mlx5e_decompress_cqes_cont(rq, cq, 0, budget);
cqe = mlx5_cqwq_get_cqe(&cq->wq);
- if (!cqe)
+ if (!cqe) {
+ if (unlikely(work_done))
+ goto out;
return 0;
-
- xdpsq = &rq->xdpsq;
+ }
do {
if (mlx5_get_cqe_format(cqe) == MLX5_COMPRESSED) {
@@ -1179,6 +1180,7 @@ int mlx5e_poll_rx_cq(struct mlx5e_cq *cq
rq->handle_rx_cqe(rq, cqe);
} while ((++work_done < budget) && (cqe = mlx5_cqwq_get_cqe(&cq->wq)));
+out:
if (xdpsq->doorbell) {
mlx5e_xmit_xdp_doorbell(xdpsq);
xdpsq->doorbell = false;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jörgen Storvist <[email protected]>
commit 4b2c01ad902ec02fa962b233decd2f14be3714ba upstream.
Added USB serial option driver support for Fibocom NL678 series cellular
module: VID 2cb7 and PIDs 0x0104 and 0x0105.
Reserved network and ADB interfaces.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0104 Rev=03.10
S: Manufacturer=Fibocom
S: Product=Fibocom NL678-E Modem
S: SerialNumber=12345678
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0105 Rev=03.10
S: Manufacturer=Fibocom
S: Product=Fibocom NL678-E Modem
S: SerialNumber=12345678
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
Signed-off-by: Jörgen Storvist <[email protected]>
Cc: stable <[email protected]>
Acked-by: Johan Hovold <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/serial/option.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -1955,6 +1955,10 @@ static const struct usb_device_id option
{ USB_DEVICE_AND_INTERFACE_INFO(0x03f0, 0xa31d, 0xff, 0x06, 0x1b) },
{ USB_DEVICE(0x1508, 0x1001), /* Fibocom NL668 */
.driver_info = RSVD(4) | RSVD(5) | RSVD(6) },
+ { USB_DEVICE(0x2cb7, 0x0104), /* Fibocom NL678 series */
+ .driver_info = RSVD(4) | RSVD(5) },
+ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
+ .driver_info = RSVD(6) },
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, option_ids);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Carpenter <[email protected]>
[ Upstream commit b26322d2ac6c1c1087af73856531bb836f6963ca ]
The function should return an error if create_singlethread_workqueue()
fails.
Fixes: 34877a15f787 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -4247,6 +4247,7 @@ int stmmac_dvr_probe(struct device *devi
priv->wq = create_singlethread_workqueue("stmmac_wq");
if (!priv->wq) {
dev_err(priv->device, "failed to create workqueue\n");
+ ret = -ENOMEM;
goto error_wq;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Takashi Sakamoto <[email protected]>
commit ada79fa5a0b374dd2c2262137c734da7524a8263 upstream.
In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a
second argument for 'the number of bytes in payload of isochronous
packet'. However, an incoming packet handler without CIP header uses the
value as 'the number of quadlets in the payload'. This brings userspace
applications to receive the number of PCM frames as four times against
real time.
This commit fixes the bug.
Cc: <[email protected]> # v4.12+
Fixes: 3b196c394dd ('ALSA: firewire-lib: add no-header packet processing')
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/firewire/amdtp-stream.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/sound/firewire/amdtp-stream.c
+++ b/sound/firewire/amdtp-stream.c
@@ -629,15 +629,17 @@ end:
}
static int handle_in_packet_without_header(struct amdtp_stream *s,
- unsigned int payload_quadlets, unsigned int cycle,
+ unsigned int payload_length, unsigned int cycle,
unsigned int index)
{
__be32 *buffer;
+ unsigned int payload_quadlets;
unsigned int data_blocks;
struct snd_pcm_substream *pcm;
unsigned int pcm_frames;
buffer = s->buffer.packets[s->packet_index].buffer;
+ payload_quadlets = payload_length / 4;
data_blocks = payload_quadlets / s->data_block_quadlets;
trace_in_packet_without_header(s, cycle, payload_quadlets, data_blocks,
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jörgen Storvist <[email protected]>
[ Upstream commit 7c3db4105ce8d69bcb5c04bfa9acd1e9119af8d5 ]
Added support for Fibocom NL678 series cellular module QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets.
Signed-off-by: Jörgen Storvist <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/usb/qmi_wwan.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1265,6 +1265,7 @@ static const struct usb_device_id produc
{QMI_QUIRK_SET_DTR(0x2c7c, 0x0121, 4)}, /* Quectel EC21 Mini PCIe */
{QMI_QUIRK_SET_DTR(0x2c7c, 0x0191, 4)}, /* Quectel EG91 */
{QMI_FIXED_INTF(0x2c7c, 0x0296, 4)}, /* Quectel BG96 */
+ {QMI_QUIRK_SET_DTR(0x2cb7, 0x0104, 4)}, /* Fibocom NL678 series */
/* 4. Gobi 1000 devices */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jörgen Storvist <[email protected]>
[ Upstream commit 1986af16e8ed355822600c24b3d2f0be46b573df ]
Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <[email protected]>
Acked-by: Bjørn Mork <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/usb/qmi_wwan.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1230,6 +1230,7 @@ static const struct usb_device_id produc
{QMI_FIXED_INTF(0x1bc7, 0x1101, 3)}, /* Telit ME910 dual modem */
{QMI_FIXED_INTF(0x1bc7, 0x1200, 5)}, /* Telit LE920 */
{QMI_QUIRK_SET_DTR(0x1bc7, 0x1201, 2)}, /* Telit LE920, LE920A4 */
+ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1900, 1)}, /* Telit LN940 series */
{QMI_FIXED_INTF(0x1c9e, 0x9801, 3)}, /* Telewell TW-3G HSPA+ */
{QMI_FIXED_INTF(0x1c9e, 0x9803, 4)}, /* Telewell TW-3G HSPA+ */
{QMI_FIXED_INTF(0x1c9e, 0x9b01, 3)}, /* XS Stick W100-2 from 4G Systems */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Willem de Bruijn <[email protected]>
[ Upstream commit 6b8d95f1795c42161dc0984b6863e95d6acf24ed ]
Validate packet socket address length if a length is given. Zero
length is equivalent to not setting an address.
Fixes: 99137b7888f4 ("packet: validate address length")
Reported-by: Ido Schimmel <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/packet/af_packet.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -2625,7 +2625,7 @@ static int tpacket_snd(struct packet_soc
sll_addr)))
goto out;
proto = saddr->sll_protocol;
- addr = saddr->sll_addr;
+ addr = saddr->sll_halen ? saddr->sll_addr : NULL;
dev = dev_get_by_index(sock_net(&po->sk), saddr->sll_ifindex);
if (addr && dev && saddr->sll_halen < dev->addr_len)
goto out;
@@ -2825,7 +2825,7 @@ static int packet_snd(struct socket *soc
if (msg->msg_namelen < (saddr->sll_halen + offsetof(struct sockaddr_ll, sll_addr)))
goto out;
proto = saddr->sll_protocol;
- addr = saddr->sll_addr;
+ addr = saddr->sll_halen ? saddr->sll_addr : NULL;
dev = dev_get_by_index(sock_net(sk), saddr->sll_ifindex);
if (addr && dev && saddr->sll_halen < dev->addr_len)
goto out;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marcin Wojtas <[email protected]>
[ Upstream commit e735fd55b94bb48363737db3b1d57627c1a16b47 ]
Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.
The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.
This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Marcin Wojtas <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/marvell/mvneta.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -406,7 +406,6 @@ struct mvneta_port {
struct mvneta_pcpu_stats __percpu *stats;
int pkt_size;
- unsigned int frag_size;
void __iomem *base;
struct mvneta_rx_queue *rxqs;
struct mvneta_tx_queue *txqs;
@@ -2905,7 +2904,9 @@ static void mvneta_rxq_hw_init(struct mv
if (!pp->bm_priv) {
/* Set Offset */
mvneta_rxq_offset_set(pp, rxq, 0);
- mvneta_rxq_buf_size_set(pp, rxq, pp->frag_size);
+ mvneta_rxq_buf_size_set(pp, rxq, PAGE_SIZE < SZ_64K ?
+ PAGE_SIZE :
+ MVNETA_RX_BUF_SIZE(pp->pkt_size));
mvneta_rxq_bm_disable(pp, rxq);
mvneta_rxq_fill(pp, rxq, rxq->size);
} else {
@@ -3749,7 +3750,6 @@ static int mvneta_open(struct net_device
int ret;
pp->pkt_size = MVNETA_RX_PKT_SIZE(pp->dev->mtu);
- pp->frag_size = PAGE_SIZE;
ret = mvneta_setup_rxqs(pp);
if (ret)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jia-Ju Bai <[email protected]>
commit c85400f886e3d41e69966470879f635a2b50084c upstream.
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/host/r8a66597-hcd.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/drivers/usb/host/r8a66597-hcd.c
+++ b/drivers/usb/host/r8a66597-hcd.c
@@ -1979,6 +1979,8 @@ static int r8a66597_urb_dequeue(struct u
static void r8a66597_endpoint_disable(struct usb_hcd *hcd,
struct usb_host_endpoint *hep)
+__acquires(r8a66597->lock)
+__releases(r8a66597->lock)
{
struct r8a66597 *r8a66597 = hcd_to_r8a66597(hcd);
struct r8a66597_pipe *pipe = (struct r8a66597_pipe *)hep->hcpriv;
@@ -1991,13 +1993,14 @@ static void r8a66597_endpoint_disable(st
return;
pipenum = pipe->info.pipenum;
+ spin_lock_irqsave(&r8a66597->lock, flags);
if (pipenum == 0) {
kfree(hep->hcpriv);
hep->hcpriv = NULL;
+ spin_unlock_irqrestore(&r8a66597->lock, flags);
return;
}
- spin_lock_irqsave(&r8a66597->lock, flags);
pipe_stop(r8a66597, pipe);
pipe_irq_disable(r8a66597, pipenum);
disable_irq_empty(r8a66597, pipenum);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Colin Ian King <[email protected]>
commit c58eef061dda7d843dcc0ad6fea7e597d4c377c0 upstream.
Currently the cmd.read_write setting is not initialized so it contains
garbage from the stack. Fix this by setting it to 0 to indicate a
read is required.
Detected by CoverityScan, CID#1357925 ("Uninitialized scalar variable")
Fixes: c5c77ba18ea6 ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Colin Ian King <[email protected]>
Cc: stable <[email protected]>
Acked-by: Ajay Singh <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/staging/wilc1000/wilc_sdio.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/staging/wilc1000/wilc_sdio.c
+++ b/drivers/staging/wilc1000/wilc_sdio.c
@@ -831,6 +831,7 @@ static int sdio_read_int(struct wilc *wi
if (!g_sdio.irq_gpio) {
int i;
+ cmd.read_write = 0;
cmd.function = 1;
cmd.address = 0x04;
cmd.data = 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans de Goede <[email protected]>
commit 984bfb398a3af6fa9b7e80165e524933b0616686 upstream.
The Clapper model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Swanky model.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Clapper that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
Cc: [email protected]
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/soc/intel/boards/cht_bsw_max98090_ti.c | 7 +++++++
1 file changed, 7 insertions(+)
--- a/sound/soc/intel/boards/cht_bsw_max98090_ti.c
+++ b/sound/soc/intel/boards/cht_bsw_max98090_ti.c
@@ -390,6 +390,13 @@ static struct snd_soc_card snd_soc_card_
static const struct dmi_system_id cht_max98090_quirk_table[] = {
{
+ /* Clapper model Chromebook */
+ .matches = {
+ DMI_MATCH(DMI_PRODUCT_NAME, "Clapper"),
+ },
+ .driver_data = (void *)QUIRK_PMC_PLT_CLK_0,
+ },
+ {
/* Swanky model Chromebook (Toshiba Chromebook 2) */
.matches = {
DMI_MATCH(DMI_PRODUCT_NAME, "Swanky"),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sanjeev Chugh <[email protected]>
commit 1e3c336ad8f40f88a8961c434640920fe35cc08b upstream.
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <[email protected]>
Fixes: a4891f105837 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/input/touchscreen/atmel_mxt_ts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/input/touchscreen/atmel_mxt_ts.c
+++ b/drivers/input/touchscreen/atmel_mxt_ts.c
@@ -1586,10 +1586,10 @@ static int mxt_update_cfg(struct mxt_dat
/* T7 config may have changed */
mxt_init_t7_power_cfg(data);
-release_raw:
- kfree(cfg.raw);
release_mem:
kfree(cfg.mem);
+release_raw:
+ kfree(cfg.raw);
return ret;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Heikki Krogerus <[email protected]>
commit c3788cd9963eb2e77de3c24142fb7c67b61f1a26 upstream.
That makes the USB role switch support option visible and
selectable for the user. The class driver is also moved to
drivers/usb/roles/ directory.
This will fix an issue that we have with the Intel USB role
switch driver on systems that don't have USB Type-C connectors:
Intel USB role switch driver depends on the USB role switch
class as it should, but since there was no way for the user
to enable the USB role switch class, there was also no way
to select that driver. USB Type-C drivers select the USB
role switch class which makes the Intel USB role switch
driver available and therefore hides the problem.
So in practice Intel USB role switch driver was depending on
USB Type-C drivers.
Fixes: f6fb9ec02be1 ("usb: roles: Add Intel xHCI USB role switch driver")
Cc: <[email protected]>
Signed-off-by: Heikki Krogerus <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/Kconfig | 4
drivers/usb/common/Makefile | 1
drivers/usb/common/roles.c | 314 --------------------------------------------
drivers/usb/roles/Kconfig | 13 +
drivers/usb/roles/Makefile | 4
drivers/usb/roles/class.c | 314 ++++++++++++++++++++++++++++++++++++++++++++
6 files changed, 330 insertions(+), 320 deletions(-)
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -205,8 +205,4 @@ config USB_ULPI_BUS
To compile this driver as a module, choose M here: the module will
be called ulpi.
-config USB_ROLE_SWITCH
- tristate
- select USB_COMMON
-
endif # USB_SUPPORT
--- a/drivers/usb/common/Makefile
+++ b/drivers/usb/common/Makefile
@@ -9,4 +9,3 @@ usb-common-$(CONFIG_USB_LED_TRIG) += led
obj-$(CONFIG_USB_OTG_FSM) += usb-otg-fsm.o
obj-$(CONFIG_USB_ULPI_BUS) += ulpi.o
-obj-$(CONFIG_USB_ROLE_SWITCH) += roles.o
--- a/drivers/usb/common/roles.c
+++ /dev/null
@@ -1,314 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * USB Role Switch Support
- *
- * Copyright (C) 2018 Intel Corporation
- * Author: Heikki Krogerus <[email protected]>
- * Hans de Goede <[email protected]>
- */
-
-#include <linux/usb/role.h>
-#include <linux/device.h>
-#include <linux/module.h>
-#include <linux/mutex.h>
-#include <linux/slab.h>
-
-static struct class *role_class;
-
-struct usb_role_switch {
- struct device dev;
- struct mutex lock; /* device lock*/
- enum usb_role role;
-
- /* From descriptor */
- struct device *usb2_port;
- struct device *usb3_port;
- struct device *udc;
- usb_role_switch_set_t set;
- usb_role_switch_get_t get;
- bool allow_userspace_control;
-};
-
-#define to_role_switch(d) container_of(d, struct usb_role_switch, dev)
-
-/**
- * usb_role_switch_set_role - Set USB role for a switch
- * @sw: USB role switch
- * @role: USB role to be switched to
- *
- * Set USB role @role for @sw.
- */
-int usb_role_switch_set_role(struct usb_role_switch *sw, enum usb_role role)
-{
- int ret;
-
- if (IS_ERR_OR_NULL(sw))
- return 0;
-
- mutex_lock(&sw->lock);
-
- ret = sw->set(sw->dev.parent, role);
- if (!ret)
- sw->role = role;
-
- mutex_unlock(&sw->lock);
-
- return ret;
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_set_role);
-
-/**
- * usb_role_switch_get_role - Get the USB role for a switch
- * @sw: USB role switch
- *
- * Depending on the role-switch-driver this function returns either a cached
- * value of the last set role, or reads back the actual value from the hardware.
- */
-enum usb_role usb_role_switch_get_role(struct usb_role_switch *sw)
-{
- enum usb_role role;
-
- if (IS_ERR_OR_NULL(sw))
- return USB_ROLE_NONE;
-
- mutex_lock(&sw->lock);
-
- if (sw->get)
- role = sw->get(sw->dev.parent);
- else
- role = sw->role;
-
- mutex_unlock(&sw->lock);
-
- return role;
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_get_role);
-
-static int __switch_match(struct device *dev, const void *name)
-{
- return !strcmp((const char *)name, dev_name(dev));
-}
-
-static void *usb_role_switch_match(struct device_connection *con, int ep,
- void *data)
-{
- struct device *dev;
-
- dev = class_find_device(role_class, NULL, con->endpoint[ep],
- __switch_match);
-
- return dev ? to_role_switch(dev) : ERR_PTR(-EPROBE_DEFER);
-}
-
-/**
- * usb_role_switch_get - Find USB role switch linked with the caller
- * @dev: The caller device
- *
- * Finds and returns role switch linked with @dev. The reference count for the
- * found switch is incremented.
- */
-struct usb_role_switch *usb_role_switch_get(struct device *dev)
-{
- struct usb_role_switch *sw;
-
- sw = device_connection_find_match(dev, "usb-role-switch", NULL,
- usb_role_switch_match);
-
- if (!IS_ERR_OR_NULL(sw))
- WARN_ON(!try_module_get(sw->dev.parent->driver->owner));
-
- return sw;
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_get);
-
-/**
- * usb_role_switch_put - Release handle to a switch
- * @sw: USB Role Switch
- *
- * Decrement reference count for @sw.
- */
-void usb_role_switch_put(struct usb_role_switch *sw)
-{
- if (!IS_ERR_OR_NULL(sw)) {
- put_device(&sw->dev);
- module_put(sw->dev.parent->driver->owner);
- }
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_put);
-
-static umode_t
-usb_role_switch_is_visible(struct kobject *kobj, struct attribute *attr, int n)
-{
- struct device *dev = container_of(kobj, typeof(*dev), kobj);
- struct usb_role_switch *sw = to_role_switch(dev);
-
- if (sw->allow_userspace_control)
- return attr->mode;
-
- return 0;
-}
-
-static const char * const usb_roles[] = {
- [USB_ROLE_NONE] = "none",
- [USB_ROLE_HOST] = "host",
- [USB_ROLE_DEVICE] = "device",
-};
-
-static ssize_t
-role_show(struct device *dev, struct device_attribute *attr, char *buf)
-{
- struct usb_role_switch *sw = to_role_switch(dev);
- enum usb_role role = usb_role_switch_get_role(sw);
-
- return sprintf(buf, "%s\n", usb_roles[role]);
-}
-
-static ssize_t role_store(struct device *dev, struct device_attribute *attr,
- const char *buf, size_t size)
-{
- struct usb_role_switch *sw = to_role_switch(dev);
- int ret;
-
- ret = sysfs_match_string(usb_roles, buf);
- if (ret < 0) {
- bool res;
-
- /* Extra check if the user wants to disable the switch */
- ret = kstrtobool(buf, &res);
- if (ret || res)
- return -EINVAL;
- }
-
- ret = usb_role_switch_set_role(sw, ret);
- if (ret)
- return ret;
-
- return size;
-}
-static DEVICE_ATTR_RW(role);
-
-static struct attribute *usb_role_switch_attrs[] = {
- &dev_attr_role.attr,
- NULL,
-};
-
-static const struct attribute_group usb_role_switch_group = {
- .is_visible = usb_role_switch_is_visible,
- .attrs = usb_role_switch_attrs,
-};
-
-static const struct attribute_group *usb_role_switch_groups[] = {
- &usb_role_switch_group,
- NULL,
-};
-
-static int
-usb_role_switch_uevent(struct device *dev, struct kobj_uevent_env *env)
-{
- int ret;
-
- ret = add_uevent_var(env, "USB_ROLE_SWITCH=%s", dev_name(dev));
- if (ret)
- dev_err(dev, "failed to add uevent USB_ROLE_SWITCH\n");
-
- return ret;
-}
-
-static void usb_role_switch_release(struct device *dev)
-{
- struct usb_role_switch *sw = to_role_switch(dev);
-
- kfree(sw);
-}
-
-static const struct device_type usb_role_dev_type = {
- .name = "usb_role_switch",
- .groups = usb_role_switch_groups,
- .uevent = usb_role_switch_uevent,
- .release = usb_role_switch_release,
-};
-
-/**
- * usb_role_switch_register - Register USB Role Switch
- * @parent: Parent device for the switch
- * @desc: Description of the switch
- *
- * USB Role Switch is a device capable or choosing the role for USB connector.
- * On platforms where the USB controller is dual-role capable, the controller
- * driver will need to register the switch. On platforms where the USB host and
- * USB device controllers behind the connector are separate, there will be a
- * mux, and the driver for that mux will need to register the switch.
- *
- * Returns handle to a new role switch or ERR_PTR. The content of @desc is
- * copied.
- */
-struct usb_role_switch *
-usb_role_switch_register(struct device *parent,
- const struct usb_role_switch_desc *desc)
-{
- struct usb_role_switch *sw;
- int ret;
-
- if (!desc || !desc->set)
- return ERR_PTR(-EINVAL);
-
- sw = kzalloc(sizeof(*sw), GFP_KERNEL);
- if (!sw)
- return ERR_PTR(-ENOMEM);
-
- mutex_init(&sw->lock);
-
- sw->allow_userspace_control = desc->allow_userspace_control;
- sw->usb2_port = desc->usb2_port;
- sw->usb3_port = desc->usb3_port;
- sw->udc = desc->udc;
- sw->set = desc->set;
- sw->get = desc->get;
-
- sw->dev.parent = parent;
- sw->dev.class = role_class;
- sw->dev.type = &usb_role_dev_type;
- dev_set_name(&sw->dev, "%s-role-switch", dev_name(parent));
-
- ret = device_register(&sw->dev);
- if (ret) {
- put_device(&sw->dev);
- return ERR_PTR(ret);
- }
-
- /* TODO: Symlinks for the host port and the device controller. */
-
- return sw;
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_register);
-
-/**
- * usb_role_switch_unregister - Unregsiter USB Role Switch
- * @sw: USB Role Switch
- *
- * Unregister switch that was registered with usb_role_switch_register().
- */
-void usb_role_switch_unregister(struct usb_role_switch *sw)
-{
- if (!IS_ERR_OR_NULL(sw))
- device_unregister(&sw->dev);
-}
-EXPORT_SYMBOL_GPL(usb_role_switch_unregister);
-
-static int __init usb_roles_init(void)
-{
- role_class = class_create(THIS_MODULE, "usb_role");
- return PTR_ERR_OR_ZERO(role_class);
-}
-subsys_initcall(usb_roles_init);
-
-static void __exit usb_roles_exit(void)
-{
- class_destroy(role_class);
-}
-module_exit(usb_roles_exit);
-
-MODULE_AUTHOR("Heikki Krogerus <[email protected]>");
-MODULE_AUTHOR("Hans de Goede <[email protected]>");
-MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("USB Role Class");
--- a/drivers/usb/roles/Kconfig
+++ b/drivers/usb/roles/Kconfig
@@ -1,3 +1,16 @@
+config USB_ROLE_SWITCH
+ tristate "USB Role Switch Support"
+ help
+ USB Role Switch is a device that can select the USB role - host or
+ device - for a USB port (connector). In most cases dual-role capable
+ USB controller will also represent the switch, but on some platforms
+ multiplexer/demultiplexer switch is used to route the data lines on
+ the USB connector between separate USB host and device controllers.
+
+ Say Y here if your USB connectors support both device and host roles.
+ To compile the driver as module, choose M here: the module will be
+ called roles.ko.
+
if USB_ROLE_SWITCH
config USB_ROLES_INTEL_XHCI
--- a/drivers/usb/roles/Makefile
+++ b/drivers/usb/roles/Makefile
@@ -1 +1,3 @@
-obj-$(CONFIG_USB_ROLES_INTEL_XHCI) += intel-xhci-usb-role-switch.o
+obj-$(CONFIG_USB_ROLE_SWITCH) += roles.o
+roles-y := class.o
+obj-$(CONFIG_USB_ROLES_INTEL_XHCI) += intel-xhci-usb-role-switch.o
--- /dev/null
+++ b/drivers/usb/roles/class.c
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Role Switch Support
+ *
+ * Copyright (C) 2018 Intel Corporation
+ * Author: Heikki Krogerus <[email protected]>
+ * Hans de Goede <[email protected]>
+ */
+
+#include <linux/usb/role.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+
+static struct class *role_class;
+
+struct usb_role_switch {
+ struct device dev;
+ struct mutex lock; /* device lock*/
+ enum usb_role role;
+
+ /* From descriptor */
+ struct device *usb2_port;
+ struct device *usb3_port;
+ struct device *udc;
+ usb_role_switch_set_t set;
+ usb_role_switch_get_t get;
+ bool allow_userspace_control;
+};
+
+#define to_role_switch(d) container_of(d, struct usb_role_switch, dev)
+
+/**
+ * usb_role_switch_set_role - Set USB role for a switch
+ * @sw: USB role switch
+ * @role: USB role to be switched to
+ *
+ * Set USB role @role for @sw.
+ */
+int usb_role_switch_set_role(struct usb_role_switch *sw, enum usb_role role)
+{
+ int ret;
+
+ if (IS_ERR_OR_NULL(sw))
+ return 0;
+
+ mutex_lock(&sw->lock);
+
+ ret = sw->set(sw->dev.parent, role);
+ if (!ret)
+ sw->role = role;
+
+ mutex_unlock(&sw->lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_set_role);
+
+/**
+ * usb_role_switch_get_role - Get the USB role for a switch
+ * @sw: USB role switch
+ *
+ * Depending on the role-switch-driver this function returns either a cached
+ * value of the last set role, or reads back the actual value from the hardware.
+ */
+enum usb_role usb_role_switch_get_role(struct usb_role_switch *sw)
+{
+ enum usb_role role;
+
+ if (IS_ERR_OR_NULL(sw))
+ return USB_ROLE_NONE;
+
+ mutex_lock(&sw->lock);
+
+ if (sw->get)
+ role = sw->get(sw->dev.parent);
+ else
+ role = sw->role;
+
+ mutex_unlock(&sw->lock);
+
+ return role;
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_get_role);
+
+static int __switch_match(struct device *dev, const void *name)
+{
+ return !strcmp((const char *)name, dev_name(dev));
+}
+
+static void *usb_role_switch_match(struct device_connection *con, int ep,
+ void *data)
+{
+ struct device *dev;
+
+ dev = class_find_device(role_class, NULL, con->endpoint[ep],
+ __switch_match);
+
+ return dev ? to_role_switch(dev) : ERR_PTR(-EPROBE_DEFER);
+}
+
+/**
+ * usb_role_switch_get - Find USB role switch linked with the caller
+ * @dev: The caller device
+ *
+ * Finds and returns role switch linked with @dev. The reference count for the
+ * found switch is incremented.
+ */
+struct usb_role_switch *usb_role_switch_get(struct device *dev)
+{
+ struct usb_role_switch *sw;
+
+ sw = device_connection_find_match(dev, "usb-role-switch", NULL,
+ usb_role_switch_match);
+
+ if (!IS_ERR_OR_NULL(sw))
+ WARN_ON(!try_module_get(sw->dev.parent->driver->owner));
+
+ return sw;
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_get);
+
+/**
+ * usb_role_switch_put - Release handle to a switch
+ * @sw: USB Role Switch
+ *
+ * Decrement reference count for @sw.
+ */
+void usb_role_switch_put(struct usb_role_switch *sw)
+{
+ if (!IS_ERR_OR_NULL(sw)) {
+ put_device(&sw->dev);
+ module_put(sw->dev.parent->driver->owner);
+ }
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_put);
+
+static umode_t
+usb_role_switch_is_visible(struct kobject *kobj, struct attribute *attr, int n)
+{
+ struct device *dev = container_of(kobj, typeof(*dev), kobj);
+ struct usb_role_switch *sw = to_role_switch(dev);
+
+ if (sw->allow_userspace_control)
+ return attr->mode;
+
+ return 0;
+}
+
+static const char * const usb_roles[] = {
+ [USB_ROLE_NONE] = "none",
+ [USB_ROLE_HOST] = "host",
+ [USB_ROLE_DEVICE] = "device",
+};
+
+static ssize_t
+role_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+ struct usb_role_switch *sw = to_role_switch(dev);
+ enum usb_role role = usb_role_switch_get_role(sw);
+
+ return sprintf(buf, "%s\n", usb_roles[role]);
+}
+
+static ssize_t role_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t size)
+{
+ struct usb_role_switch *sw = to_role_switch(dev);
+ int ret;
+
+ ret = sysfs_match_string(usb_roles, buf);
+ if (ret < 0) {
+ bool res;
+
+ /* Extra check if the user wants to disable the switch */
+ ret = kstrtobool(buf, &res);
+ if (ret || res)
+ return -EINVAL;
+ }
+
+ ret = usb_role_switch_set_role(sw, ret);
+ if (ret)
+ return ret;
+
+ return size;
+}
+static DEVICE_ATTR_RW(role);
+
+static struct attribute *usb_role_switch_attrs[] = {
+ &dev_attr_role.attr,
+ NULL,
+};
+
+static const struct attribute_group usb_role_switch_group = {
+ .is_visible = usb_role_switch_is_visible,
+ .attrs = usb_role_switch_attrs,
+};
+
+static const struct attribute_group *usb_role_switch_groups[] = {
+ &usb_role_switch_group,
+ NULL,
+};
+
+static int
+usb_role_switch_uevent(struct device *dev, struct kobj_uevent_env *env)
+{
+ int ret;
+
+ ret = add_uevent_var(env, "USB_ROLE_SWITCH=%s", dev_name(dev));
+ if (ret)
+ dev_err(dev, "failed to add uevent USB_ROLE_SWITCH\n");
+
+ return ret;
+}
+
+static void usb_role_switch_release(struct device *dev)
+{
+ struct usb_role_switch *sw = to_role_switch(dev);
+
+ kfree(sw);
+}
+
+static const struct device_type usb_role_dev_type = {
+ .name = "usb_role_switch",
+ .groups = usb_role_switch_groups,
+ .uevent = usb_role_switch_uevent,
+ .release = usb_role_switch_release,
+};
+
+/**
+ * usb_role_switch_register - Register USB Role Switch
+ * @parent: Parent device for the switch
+ * @desc: Description of the switch
+ *
+ * USB Role Switch is a device capable or choosing the role for USB connector.
+ * On platforms where the USB controller is dual-role capable, the controller
+ * driver will need to register the switch. On platforms where the USB host and
+ * USB device controllers behind the connector are separate, there will be a
+ * mux, and the driver for that mux will need to register the switch.
+ *
+ * Returns handle to a new role switch or ERR_PTR. The content of @desc is
+ * copied.
+ */
+struct usb_role_switch *
+usb_role_switch_register(struct device *parent,
+ const struct usb_role_switch_desc *desc)
+{
+ struct usb_role_switch *sw;
+ int ret;
+
+ if (!desc || !desc->set)
+ return ERR_PTR(-EINVAL);
+
+ sw = kzalloc(sizeof(*sw), GFP_KERNEL);
+ if (!sw)
+ return ERR_PTR(-ENOMEM);
+
+ mutex_init(&sw->lock);
+
+ sw->allow_userspace_control = desc->allow_userspace_control;
+ sw->usb2_port = desc->usb2_port;
+ sw->usb3_port = desc->usb3_port;
+ sw->udc = desc->udc;
+ sw->set = desc->set;
+ sw->get = desc->get;
+
+ sw->dev.parent = parent;
+ sw->dev.class = role_class;
+ sw->dev.type = &usb_role_dev_type;
+ dev_set_name(&sw->dev, "%s-role-switch", dev_name(parent));
+
+ ret = device_register(&sw->dev);
+ if (ret) {
+ put_device(&sw->dev);
+ return ERR_PTR(ret);
+ }
+
+ /* TODO: Symlinks for the host port and the device controller. */
+
+ return sw;
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_register);
+
+/**
+ * usb_role_switch_unregister - Unregsiter USB Role Switch
+ * @sw: USB Role Switch
+ *
+ * Unregister switch that was registered with usb_role_switch_register().
+ */
+void usb_role_switch_unregister(struct usb_role_switch *sw)
+{
+ if (!IS_ERR_OR_NULL(sw))
+ device_unregister(&sw->dev);
+}
+EXPORT_SYMBOL_GPL(usb_role_switch_unregister);
+
+static int __init usb_roles_init(void)
+{
+ role_class = class_create(THIS_MODULE, "usb_role");
+ return PTR_ERR_OR_ZERO(role_class);
+}
+subsys_initcall(usb_roles_init);
+
+static void __exit usb_roles_exit(void)
+{
+ class_destroy(role_class);
+}
+module_exit(usb_roles_exit);
+
+MODULE_AUTHOR("Heikki Krogerus <[email protected]>");
+MODULE_AUTHOR("Hans de Goede <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("USB Role Class");
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gustavo A. R. Silva <[email protected]>
commit 4aea96f4237cea0c51a8bc87c0db31f0f932f1f0 upstream.
info.mode and info.port are indirectly controlled by user-space,
hence leading to a potential exploitation of the Spectre variant 1
vulnerability.
These issues were detected with the help of Smatch:
sound/synth/emux/emux_hwdep.c:72 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[i]->ctrls' [w] (local cap)
sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs' [w] (local cap)
sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[info.port]->ctrls' [w] (local cap)
Fix this by sanitizing both info.mode and info.port before using them
to index emu->portptrs[i]->ctrls, emu->portptrs[info.port]->ctrls and
emu->portptrs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Cc: [email protected]
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/synth/emux/emux_hwdep.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
--- a/sound/synth/emux/emux_hwdep.c
+++ b/sound/synth/emux/emux_hwdep.c
@@ -22,9 +22,9 @@
#include <sound/core.h>
#include <sound/hwdep.h>
#include <linux/uaccess.h>
+#include <linux/nospec.h>
#include "emux_voice.h"
-
#define TMP_CLIENT_ID 0x1001
/*
@@ -66,13 +66,16 @@ snd_emux_hwdep_misc_mode(struct snd_emux
return -EFAULT;
if (info.mode < 0 || info.mode >= EMUX_MD_END)
return -EINVAL;
+ info.mode = array_index_nospec(info.mode, EMUX_MD_END);
if (info.port < 0) {
for (i = 0; i < emu->num_ports; i++)
emu->portptrs[i]->ctrls[info.mode] = info.value;
} else {
- if (info.port < emu->num_ports)
+ if (info.port < emu->num_ports) {
+ info.port = array_index_nospec(info.port, emu->num_ports);
emu->portptrs[info.port]->ctrls[info.mode] = info.value;
+ }
}
return 0;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Michal Hocko <[email protected]>
commit 5b5e4d623ec8a34689df98e42d038a3b594d2ff9 upstream.
Swap storage is restricted to max_swapfile_size (~16TB on x86_64) whenever
the system is deemed affected by L1TF vulnerability. Even though the limit
is quite high for most deployments it seems to be too restrictive for
deployments which are willing to live with the mitigation disabled.
We have a customer to deploy 8x 6,4TB PCIe/NVMe SSD swap devices which is
clearly out of the limit.
Drop the swap restriction when l1tf=off is specified. It also doesn't make
much sense to warn about too much memory for the l1tf mitigation when it is
forcefully disabled by the administrator.
[ tglx: Folded the documentation delta change ]
Fixes: 377eeaa8e11f ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2")
Signed-off-by: Michal Hocko <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Pavel Tatashin <[email protected]>
Reviewed-by: Andi Kleen <[email protected]>
Acked-by: Jiri Kosina <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
Documentation/admin-guide/kernel-parameters.txt | 3 +++
Documentation/admin-guide/l1tf.rst | 6 +++++-
arch/x86/kernel/cpu/bugs.c | 3 ++-
arch/x86/mm/init.c | 2 +-
4 files changed, 11 insertions(+), 3 deletions(-)
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -2073,6 +2073,9 @@
off
Disables hypervisor mitigations and doesn't
emit any warnings.
+ It also drops the swap size and available
+ RAM limit restriction on both hypervisor and
+ bare metal.
Default is 'flush'.
--- a/Documentation/admin-guide/l1tf.rst
+++ b/Documentation/admin-guide/l1tf.rst
@@ -405,6 +405,9 @@ time with the option "l1tf=". The valid
off Disables hypervisor mitigations and doesn't emit any
warnings.
+ It also drops the swap size and available RAM limit restrictions
+ on both hypervisor and bare metal.
+
============ =============================================================
The default is 'flush'. For details about L1D flushing see :ref:`l1d_flush`.
@@ -576,7 +579,8 @@ Default mitigations
The kernel default mitigations for vulnerable processors are:
- PTE inversion to protect against malicious user space. This is done
- unconditionally and cannot be controlled.
+ unconditionally and cannot be controlled. The swap storage is limited
+ to ~16TB.
- L1D conditional flushing on VMENTER when EPT is enabled for
a guest.
--- a/arch/x86/kernel/cpu/bugs.c
+++ b/arch/x86/kernel/cpu/bugs.c
@@ -1000,7 +1000,8 @@ static void __init l1tf_select_mitigatio
#endif
half_pa = (u64)l1tf_pfn_limit() << PAGE_SHIFT;
- if (e820__mapped_any(half_pa, ULLONG_MAX - half_pa, E820_TYPE_RAM)) {
+ if (l1tf_mitigation != L1TF_MITIGATION_OFF &&
+ e820__mapped_any(half_pa, ULLONG_MAX - half_pa, E820_TYPE_RAM)) {
pr_warn("System has more than MAX_PA/2 memory. L1TF mitigation not effective.\n");
pr_info("You may make it effective by booting the kernel with mem=%llu parameter.\n",
half_pa);
--- a/arch/x86/mm/init.c
+++ b/arch/x86/mm/init.c
@@ -932,7 +932,7 @@ unsigned long max_swapfile_size(void)
pages = generic_max_swapfile_size();
- if (boot_cpu_has_bug(X86_BUG_L1TF)) {
+ if (boot_cpu_has_bug(X86_BUG_L1TF) && l1tf_mitigation != L1TF_MITIGATION_OFF) {
/* Limit the swap file size to MAX_PA/2 for L1TF workaround */
unsigned long long l1tf_limit = l1tf_pfn_limit();
/*
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Martin Blumenstingl <[email protected]>
commit cc10ce0c51b13d1566d0ec1dcb472fb86330b391 upstream.
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a1def
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa6790 ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <[email protected]> # 4.19
Acked-by: Minas Harutyunyan <[email protected]>
Suggested-by: Christian Hewitt <[email protected]>
Signed-off-by: Martin Blumenstingl <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/dwc2/params.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/usb/dwc2/params.c
+++ b/drivers/usb/dwc2/params.c
@@ -110,6 +110,7 @@ static void dwc2_set_amlogic_params(stru
p->phy_type = DWC2_PHY_TYPE_PARAM_UTMI;
p->ahbcfg = GAHBCFG_HBSTLEN_INCR8 <<
GAHBCFG_HBSTLEN_SHIFT;
+ p->power_down = DWC2_POWER_DOWN_PARAM_NONE;
}
static void dwc2_set_amcc_params(struct dwc2_hsotg *hsotg)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dan Williams <[email protected]>
commit ba6f508d0ec4adb09f0a939af6d5e19cdfa8667d upstream.
Commit:
f77084d96355 "x86/mm/pat: Disable preemption around __flush_tlb_all()"
addressed a case where __flush_tlb_all() is called without preemption
being disabled. It also left a warning to catch other cases where
preemption is not disabled.
That warning triggers for the memory hotplug path which is also used for
persistent memory enabling:
WARNING: CPU: 35 PID: 911 at ./arch/x86/include/asm/tlbflush.h:460
RIP: 0010:__flush_tlb_all+0x1b/0x3a
[..]
Call Trace:
phys_pud_init+0x29c/0x2bb
kernel_physical_mapping_init+0xfc/0x219
init_memory_mapping+0x1a5/0x3b0
arch_add_memory+0x2c/0x50
devm_memremap_pages+0x3aa/0x610
pmem_attach_disk+0x585/0x700 [nd_pmem]
Andy wondered why a path that can sleep was using __flush_tlb_all() [1]
and Dave confirmed the expectation for TLB flush is for modifying /
invalidating existing PTE entries, but not initial population [2]. Drop
the usage of __flush_tlb_all() in phys_{p4d,pud,pmd}_init() on the
expectation that this path is only ever populating empty entries for the
linear map. Note, at linear map teardown time there is a call to the
all-cpu flush_tlb_all() to invalidate the removed mappings.
[1]: https://lkml.kernel.org/r/[email protected]
[2]: https://lkml.kernel.org/r/[email protected]
[ mingo: Minor readability edits. ]
Suggested-by: Dave Hansen <[email protected]>
Reported-by: Andy Lutomirski <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Acked-by: Kirill A. Shutemov <[email protected]>
Cc: <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Sebastian Andrzej Siewior <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Fixes: f77084d96355 ("x86/mm/pat: Disable preemption around __flush_tlb_all()")
Link: http://lkml.kernel.org/r/154395944713.32119.15611079023837132638.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/mm/init_64.c | 6 ------
1 file changed, 6 deletions(-)
--- a/arch/x86/mm/init_64.c
+++ b/arch/x86/mm/init_64.c
@@ -585,7 +585,6 @@ phys_pud_init(pud_t *pud_page, unsigned
paddr_end,
page_size_mask,
prot);
- __flush_tlb_all();
continue;
}
/*
@@ -628,7 +627,6 @@ phys_pud_init(pud_t *pud_page, unsigned
pud_populate(&init_mm, pud, pmd);
spin_unlock(&init_mm.page_table_lock);
}
- __flush_tlb_all();
update_page_count(PG_LEVEL_1G, pages);
@@ -669,7 +667,6 @@ phys_p4d_init(p4d_t *p4d_page, unsigned
paddr_last = phys_pud_init(pud, paddr,
paddr_end,
page_size_mask);
- __flush_tlb_all();
continue;
}
@@ -681,7 +678,6 @@ phys_p4d_init(p4d_t *p4d_page, unsigned
p4d_populate(&init_mm, p4d, pud);
spin_unlock(&init_mm.page_table_lock);
}
- __flush_tlb_all();
return paddr_last;
}
@@ -734,8 +730,6 @@ kernel_physical_mapping_init(unsigned lo
if (pgd_changed)
sync_global_pgds(vaddr_start, vaddr_end - 1);
- __flush_tlb_all();
-
return paddr_last;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Malcolm Priestley <[email protected]>
commit 255095fa7f62ff09b6f61393414535c59c6b4cb0 upstream.
commit 1a0c10ed7bb1 ("media: dvb-usb-v2: stop using coherent memory for
URBs") incorrectly adds URB_FREE_BUFFER after every urb transfer.
It cannot use this flag because it reconfigures the URBs accordingly
to suit connected devices. In doing a call to usb_free_urb is made and
invertedly frees the buffers.
The stream buffer should remain constant while driver is up.
Signed-off-by: Malcolm Priestley <[email protected]>
CC: [email protected] # v4.18+
Signed-off-by: Sean Young <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/usb/dvb-usb-v2/usb_urb.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
--- a/drivers/media/usb/dvb-usb-v2/usb_urb.c
+++ b/drivers/media/usb/dvb-usb-v2/usb_urb.c
@@ -155,7 +155,6 @@ static int usb_urb_alloc_bulk_urbs(struc
stream->props.u.bulk.buffersize,
usb_urb_complete, stream);
- stream->urb_list[i]->transfer_flags = URB_FREE_BUFFER;
stream->urbs_initialized++;
}
return 0;
@@ -186,7 +185,7 @@ static int usb_urb_alloc_isoc_urbs(struc
urb->complete = usb_urb_complete;
urb->pipe = usb_rcvisocpipe(stream->udev,
stream->props.endpoint);
- urb->transfer_flags = URB_ISO_ASAP | URB_FREE_BUFFER;
+ urb->transfer_flags = URB_ISO_ASAP;
urb->interval = stream->props.u.isoc.interval;
urb->number_of_packets = stream->props.u.isoc.framesperurb;
urb->transfer_buffer_length = stream->props.u.isoc.framesize *
@@ -210,7 +209,7 @@ static int usb_free_stream_buffers(struc
if (stream->state & USB_STATE_URB_BUF) {
while (stream->buf_num) {
stream->buf_num--;
- stream->buf_list[stream->buf_num] = NULL;
+ kfree(stream->buf_list[stream->buf_num]);
}
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marc Zyngier <[email protected]>
commit c987876a80e7bcb98a839f10dca9ce7fda4feced upstream.
Contrary to the non-VHE version of the TLB invalidation helpers, the VHE
code has interrupts enabled, meaning that we can take an interrupt in
the middle of such a sequence, and start running something else with
HCR_EL2.TGE cleared.
That's really not a good idea.
Take the heavy-handed option and disable interrupts in
__tlb_switch_to_guest_vhe, restoring them in __tlb_switch_to_host_vhe.
The latter also gain an ISB in order to make sure that TGE really has
taken effect.
Cc: [email protected]
Acked-by: Christoffer Dall <[email protected]>
Reviewed-by: James Morse <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm64/kvm/hyp/tlb.c | 35 +++++++++++++++++++++++++----------
1 file changed, 25 insertions(+), 10 deletions(-)
--- a/arch/arm64/kvm/hyp/tlb.c
+++ b/arch/arm64/kvm/hyp/tlb.c
@@ -15,14 +15,19 @@
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
+#include <linux/irqflags.h>
+
#include <asm/kvm_hyp.h>
#include <asm/kvm_mmu.h>
#include <asm/tlbflush.h>
-static void __hyp_text __tlb_switch_to_guest_vhe(struct kvm *kvm)
+static void __hyp_text __tlb_switch_to_guest_vhe(struct kvm *kvm,
+ unsigned long *flags)
{
u64 val;
+ local_irq_save(*flags);
+
/*
* With VHE enabled, we have HCR_EL2.{E2H,TGE} = {1,1}, and
* most TLB operations target EL2/EL0. In order to affect the
@@ -37,7 +42,8 @@ static void __hyp_text __tlb_switch_to_g
isb();
}
-static void __hyp_text __tlb_switch_to_guest_nvhe(struct kvm *kvm)
+static void __hyp_text __tlb_switch_to_guest_nvhe(struct kvm *kvm,
+ unsigned long *flags)
{
write_sysreg(kvm->arch.vttbr, vttbr_el2);
isb();
@@ -48,7 +54,8 @@ static hyp_alternate_select(__tlb_switch
__tlb_switch_to_guest_vhe,
ARM64_HAS_VIRT_HOST_EXTN);
-static void __hyp_text __tlb_switch_to_host_vhe(struct kvm *kvm)
+static void __hyp_text __tlb_switch_to_host_vhe(struct kvm *kvm,
+ unsigned long flags)
{
/*
* We're done with the TLB operation, let's restore the host's
@@ -56,9 +63,12 @@ static void __hyp_text __tlb_switch_to_h
*/
write_sysreg(0, vttbr_el2);
write_sysreg(HCR_HOST_VHE_FLAGS, hcr_el2);
+ isb();
+ local_irq_restore(flags);
}
-static void __hyp_text __tlb_switch_to_host_nvhe(struct kvm *kvm)
+static void __hyp_text __tlb_switch_to_host_nvhe(struct kvm *kvm,
+ unsigned long flags)
{
write_sysreg(0, vttbr_el2);
}
@@ -70,11 +80,13 @@ static hyp_alternate_select(__tlb_switch
void __hyp_text __kvm_tlb_flush_vmid_ipa(struct kvm *kvm, phys_addr_t ipa)
{
+ unsigned long flags;
+
dsb(ishst);
/* Switch to requested VMID */
kvm = kern_hyp_va(kvm);
- __tlb_switch_to_guest()(kvm);
+ __tlb_switch_to_guest()(kvm, &flags);
/*
* We could do so much better if we had the VA as well.
@@ -117,36 +129,39 @@ void __hyp_text __kvm_tlb_flush_vmid_ipa
if (!has_vhe() && icache_is_vpipt())
__flush_icache_all();
- __tlb_switch_to_host()(kvm);
+ __tlb_switch_to_host()(kvm, flags);
}
void __hyp_text __kvm_tlb_flush_vmid(struct kvm *kvm)
{
+ unsigned long flags;
+
dsb(ishst);
/* Switch to requested VMID */
kvm = kern_hyp_va(kvm);
- __tlb_switch_to_guest()(kvm);
+ __tlb_switch_to_guest()(kvm, &flags);
__tlbi(vmalls12e1is);
dsb(ish);
isb();
- __tlb_switch_to_host()(kvm);
+ __tlb_switch_to_host()(kvm, flags);
}
void __hyp_text __kvm_tlb_flush_local_vmid(struct kvm_vcpu *vcpu)
{
struct kvm *kvm = kern_hyp_va(kern_hyp_va(vcpu)->kvm);
+ unsigned long flags;
/* Switch to requested VMID */
- __tlb_switch_to_guest()(kvm);
+ __tlb_switch_to_guest()(kvm, &flags);
__tlbi(vmalle1);
dsb(nsh);
isb();
- __tlb_switch_to_host()(kvm);
+ __tlb_switch_to_host()(kvm, flags);
}
void __hyp_text __kvm_flush_vm_context(void)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans de Goede <[email protected]>
commit 94ea56cff506c769a509c5dd87904c7fe3806a81 upstream.
The Gnawty model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Clapper and Swanky models.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Gnawty that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201787
Cc: [email protected]
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Jaime Pérez <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/soc/intel/boards/cht_bsw_max98090_ti.c | 7 +++++++
1 file changed, 7 insertions(+)
--- a/sound/soc/intel/boards/cht_bsw_max98090_ti.c
+++ b/sound/soc/intel/boards/cht_bsw_max98090_ti.c
@@ -397,6 +397,13 @@ static const struct dmi_system_id cht_ma
.driver_data = (void *)QUIRK_PMC_PLT_CLK_0,
},
{
+ /* Gnawty model Chromebook (Acer Chromebook CB3-111) */
+ .matches = {
+ DMI_MATCH(DMI_PRODUCT_NAME, "Gnawty"),
+ },
+ .driver_data = (void *)QUIRK_PMC_PLT_CLK_0,
+ },
+ {
/* Swanky model Chromebook (Toshiba Chromebook 2) */
.matches = {
DMI_MATCH(DMI_PRODUCT_NAME, "Swanky"),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Miquel Raynal <[email protected]>
commit 81b1e6e6a8590a19257e37a1633bec098d499c57 upstream.
Since the addition of platform MSI support, there were two helpers
supposed to allocate/free IRQs for a device:
platform_msi_domain_alloc_irqs()
platform_msi_domain_free_irqs()
In these helpers, IRQ descriptors are allocated in the "alloc" routine
while they are freed in the "free" one.
Later, two other helpers have been added to handle IRQ domains on top
of MSI domains:
platform_msi_domain_alloc()
platform_msi_domain_free()
Seen from the outside, the logic is pretty close with the former
helpers and people used it with the same logic as before: a
platform_msi_domain_alloc() call should be balanced with a
platform_msi_domain_free() call. While this is probably what was
intended to do, the platform_msi_domain_free() does not remove/free
the IRQ descriptor(s) created/inserted in
platform_msi_domain_alloc().
One effect of such situation is that removing a module that requested
an IRQ will let one orphaned IRQ descriptor (with an allocated MSI
entry) in the device descriptors list. Next time the module will be
inserted back, one will observe that the allocation will happen twice
in the MSI domain, one time for the remaining descriptor, one time for
the new one. It also has the side effect to quickly overshoot the
maximum number of allocated MSI and then prevent any module requesting
an interrupt in the same domain to be inserted anymore.
This situation has been met with loops of insertion/removal of the
mvpp2.ko module (requesting 15 MSIs each time).
Fixes: 552c494a7666 ("platform-msi: Allow creation of a MSI-based stacked irq domain")
Cc: [email protected]
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/base/platform-msi.c | 6 ++++--
include/linux/msi.h | 2 ++
2 files changed, 6 insertions(+), 2 deletions(-)
--- a/drivers/base/platform-msi.c
+++ b/drivers/base/platform-msi.c
@@ -366,14 +366,16 @@ void platform_msi_domain_free(struct irq
unsigned int nvec)
{
struct platform_msi_priv_data *data = domain->host_data;
- struct msi_desc *desc;
- for_each_msi_entry(desc, data->dev) {
+ struct msi_desc *desc, *tmp;
+ for_each_msi_entry_safe(desc, tmp, data->dev) {
if (WARN_ON(!desc->irq || desc->nvec_used != 1))
return;
if (!(desc->irq >= virq && desc->irq < (virq + nvec)))
continue;
irq_domain_free_irqs_common(domain, desc->irq, 1);
+ list_del(&desc->list);
+ free_msi_entry(desc);
}
}
--- a/include/linux/msi.h
+++ b/include/linux/msi.h
@@ -116,6 +116,8 @@ struct msi_desc {
list_first_entry(dev_to_msi_list((dev)), struct msi_desc, list)
#define for_each_msi_entry(desc, dev) \
list_for_each_entry((desc), dev_to_msi_list((dev)), list)
+#define for_each_msi_entry_safe(desc, tmp, dev) \
+ list_for_each_entry_safe((desc), (tmp), dev_to_msi_list((dev)), list)
#ifdef CONFIG_PCI_MSI
#define first_pci_msi_entry(pdev) first_msi_entry(&(pdev)->dev)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Anholt <[email protected]>
commit 2f20fa8d12e859a03f68bdd81d75830141bc9ac9 upstream.
Fixes an oops reading this debugfs entry on BCM7278.
Signed-off-by: Eric Anholt <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Cc: <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/v3d/v3d_debugfs.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
--- a/drivers/gpu/drm/v3d/v3d_debugfs.c
+++ b/drivers/gpu/drm/v3d/v3d_debugfs.c
@@ -71,10 +71,13 @@ static int v3d_v3d_debugfs_regs(struct s
V3D_READ(v3d_hub_reg_defs[i].reg));
}
- for (i = 0; i < ARRAY_SIZE(v3d_gca_reg_defs); i++) {
- seq_printf(m, "%s (0x%04x): 0x%08x\n",
- v3d_gca_reg_defs[i].name, v3d_gca_reg_defs[i].reg,
- V3D_GCA_READ(v3d_gca_reg_defs[i].reg));
+ if (v3d->ver < 41) {
+ for (i = 0; i < ARRAY_SIZE(v3d_gca_reg_defs); i++) {
+ seq_printf(m, "%s (0x%04x): 0x%08x\n",
+ v3d_gca_reg_defs[i].name,
+ v3d_gca_reg_defs[i].reg,
+ V3D_GCA_READ(v3d_gca_reg_defs[i].reg));
+ }
}
for (core = 0; core < v3d->cores; core++) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eugeniy Paltsev <[email protected]>
commit 32e932e37e6b6e13b66add307192c7ddd40a781d upstream.
UDL doesn't support vblank functionality so we don't need to
initialize vblank here (we are able to send page flip
completion events even without vblank initialization)
Moreover current drm_vblank_init call with num_crtcs > 0 causes
sending DRM_EVENT_FLIP_COMPLETE event with zero timestamp every
time. This breaks userspace apps (for example weston) which
relies on timestamp value.
Cc: [email protected]
Signed-off-by: Eugeniy Paltsev <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/gpu/drm/udl/udl_main.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
--- a/drivers/gpu/drm/udl/udl_main.c
+++ b/drivers/gpu/drm/udl/udl_main.c
@@ -350,15 +350,10 @@ int udl_driver_load(struct drm_device *d
if (ret)
goto err;
- ret = drm_vblank_init(dev, 1);
- if (ret)
- goto err_fb;
-
drm_kms_helper_poll_init(dev);
return 0;
-err_fb:
- udl_fbdev_cleanup(dev);
+
err:
if (udl->urbs.count)
udl_free_urb_list(dev);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stephan Gerhold <[email protected]>
commit 3004cfd6204927c1294060b849029cf0c2651074 upstream.
Commit 211f658b7b40 ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: [email protected]
Signed-off-by: Stephan Gerhold <[email protected]>
Signed-off-by: Felipe Balbi <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/dwc3/dwc3-pci.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
--- a/drivers/usb/dwc3/dwc3-pci.c
+++ b/drivers/usb/dwc3/dwc3-pci.c
@@ -170,20 +170,20 @@ static int dwc3_pci_quirks(struct dwc3_p
* put the gpio descriptors again here because the phy driver
* might want to grab them, too.
*/
- gpio = devm_gpiod_get_optional(&pdev->dev, "cs",
- GPIOD_OUT_LOW);
+ gpio = gpiod_get_optional(&pdev->dev, "cs", GPIOD_OUT_LOW);
if (IS_ERR(gpio))
return PTR_ERR(gpio);
gpiod_set_value_cansleep(gpio, 1);
+ gpiod_put(gpio);
- gpio = devm_gpiod_get_optional(&pdev->dev, "reset",
- GPIOD_OUT_LOW);
+ gpio = gpiod_get_optional(&pdev->dev, "reset", GPIOD_OUT_LOW);
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
gpiod_set_value_cansleep(gpio, 1);
+ gpiod_put(gpio);
usleep_range(10000, 11000);
}
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Adrian Hunter <[email protected]>
commit ec1891afae740be581ecf5abc8bda74c4549203f upstream.
Some architectures have a single address space for kernel and user
addresses, which makes it possible to determine if an address is in
kernel space or user space. Some don't, e.g.: sparc.
Cache that info in perf_env so that, for instance, code needing to
fallback failed symbol lookups at the kernel space in single address
space arches can lookup at userspace.
Signed-off-by: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Leo Yan <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: [email protected] # 4.19
Link: http://lkml.kernel.org/r/[email protected]
[ split from a larger patch ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/arch/common.c | 10 ++++++++++
tools/perf/arch/common.h | 1 +
tools/perf/util/machine.h | 1 +
tools/perf/util/session.c | 4 ++++
4 files changed, 16 insertions(+)
--- a/tools/perf/arch/common.c
+++ b/tools/perf/arch/common.c
@@ -200,3 +200,13 @@ int perf_env__lookup_objdump(struct perf
return perf_env__lookup_binutils_path(env, "objdump", path);
}
+
+/*
+ * Some architectures have a single address space for kernel and user addresses,
+ * which makes it possible to determine if an address is in kernel space or user
+ * space.
+ */
+bool perf_env__single_address_space(struct perf_env *env)
+{
+ return strcmp(perf_env__arch(env), "sparc");
+}
--- a/tools/perf/arch/common.h
+++ b/tools/perf/arch/common.h
@@ -5,5 +5,6 @@
#include "../util/env.h"
int perf_env__lookup_objdump(struct perf_env *env, const char **path);
+bool perf_env__single_address_space(struct perf_env *env);
#endif /* ARCH_PERF_COMMON_H */
--- a/tools/perf/util/machine.h
+++ b/tools/perf/util/machine.h
@@ -42,6 +42,7 @@ struct machine {
u16 id_hdr_size;
bool comm_exec;
bool kptr_restrict_warned;
+ bool single_address_space;
char *root_dir;
char *mmap_name;
struct threads threads[THREADS__TABLE_SIZE];
--- a/tools/perf/util/session.c
+++ b/tools/perf/util/session.c
@@ -24,6 +24,7 @@
#include "thread.h"
#include "thread-stack.h"
#include "stat.h"
+#include "arch/common.h"
static int perf_session__deliver_event(struct perf_session *session,
union perf_event *event,
@@ -150,6 +151,9 @@ struct perf_session *perf_session__new(s
session->machines.host.env = &perf_env;
}
+ session->machines.host.single_address_space =
+ perf_env__single_address_space(session->machines.host.env);
+
if (!data || perf_data__is_write(data)) {
/*
* In O_RDONLY mode this will be performed when reading the
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Wandrille RONCE <[email protected]>
commit 9cf6533e8060d3896b88ea14b27f620e6504b84b upstream.
By default, there is no sound on Asus UX391UA on Linux.
This patch adds sound support on Asus UX391UA. Tested working by three
different users.
The problem has also been described at
https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1784485
Signed-off-by: Wandrille RONCE <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/hda/patch_realtek.c | 1 +
1 file changed, 1 insertion(+)
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6573,6 +6573,7 @@ static const struct snd_pci_quirk alc269
SND_PCI_QUIRK(0x1043, 0x103e, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC),
SND_PCI_QUIRK(0x1043, 0x103f, "ASUS TX300", ALC282_FIXUP_ASUS_TX300),
SND_PCI_QUIRK(0x1043, 0x106d, "Asus K53BE", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+ SND_PCI_QUIRK(0x1043, 0x10a1, "ASUS UX391UA", ALC294_FIXUP_ASUS_SPK),
SND_PCI_QUIRK(0x1043, 0x10c0, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC),
SND_PCI_QUIRK(0x1043, 0x10d0, "ASUS X540LA/X540LJ", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1043, 0x115d, "Asus 1015E", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gustavo A. R. Silva <[email protected]>
commit 0b84304ef5da92add8dc75a1b07879c5374cdb05 upstream.
info->channel is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/pci/rme9652/hdsp.c:4100 snd_hdsp_channel_info() warn: potential spectre issue 'hdsp->channel_map' [r] (local cap)
Fix this by sanitizing info->channel before using it to index hdsp->channel_map
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Also, notice that I refactored the code a bit in order to get rid of the
following checkpatch warning:
ERROR: do not use assignment in if condition
FILE: sound/pci/rme9652/hdsp.c:4103:
if ((mapped_channel = hdsp->channel_map[info->channel]) < 0)
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: [email protected]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/rme9652/hdsp.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
--- a/sound/pci/rme9652/hdsp.c
+++ b/sound/pci/rme9652/hdsp.c
@@ -30,6 +30,7 @@
#include <linux/math64.h>
#include <linux/vmalloc.h>
#include <linux/io.h>
+#include <linux/nospec.h>
#include <sound/core.h>
#include <sound/control.h>
@@ -4092,15 +4093,16 @@ static int snd_hdsp_channel_info(struct
struct snd_pcm_channel_info *info)
{
struct hdsp *hdsp = snd_pcm_substream_chip(substream);
- int mapped_channel;
+ unsigned int channel = info->channel;
- if (snd_BUG_ON(info->channel >= hdsp->max_channels))
+ if (snd_BUG_ON(channel >= hdsp->max_channels))
return -EINVAL;
+ channel = array_index_nospec(channel, hdsp->max_channels);
- if ((mapped_channel = hdsp->channel_map[info->channel]) < 0)
+ if (hdsp->channel_map[channel] < 0)
return -EINVAL;
- info->offset = mapped_channel * HDSP_CHANNEL_BUFFER_BYTES;
+ info->offset = hdsp->channel_map[channel] * HDSP_CHANNEL_BUFFER_BYTES;
info->first = 0;
info->step = 32;
return 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sean Christopherson <[email protected]>
commit e81434995081fd7efb755fd75576b35dbb0850b1 upstream.
____kvm_handle_fault_on_reboot() provides a generic exception fixup
handler that is used to cleanly handle faults on VMX/SVM instructions
during reboot (or at least try to). If there isn't a reboot in
progress, ____kvm_handle_fault_on_reboot() treats any exception as
fatal to KVM and invokes kvm_spurious_fault(), which in turn generates
a BUG() to get a stack trace and die.
When it was originally added by commit 4ecac3fd6dc2 ("KVM: Handle
virtualization instruction #UD faults during reboot"), the "call" to
kvm_spurious_fault() was handcoded as PUSH+JMP, where the PUSH'd value
is the RIP of the faulting instructing.
The PUSH+JMP trickery is necessary because the exception fixup handler
code lies outside of its associated function, e.g. right after the
function. An actual CALL from the .fixup code would show a slightly
bogus stack trace, e.g. an extra "random" function would be inserted
into the trace, as the return RIP on the stack would point to no known
function (and the unwinder will likely try to guess who owns the RIP).
Unfortunately, the JMP was replaced with a CALL when the macro was
reworked to not spin indefinitely during reboot (commit b7c4145ba2eb
"KVM: Don't spin on virt instruction faults during reboot"). This
causes the aforementioned behavior where a bogus function is inserted
into the stack trace, e.g. my builds like to blame free_kvm_area().
Revert the CALL back to a JMP. The changelog for commit b7c4145ba2eb
("KVM: Don't spin on virt instruction faults during reboot") contains
nothing that indicates the switch to CALL was deliberate. This is
backed up by the fact that the PUSH <insn RIP> was left intact.
Note that an alternative to the PUSH+JMP magic would be to JMP back
to the "real" code and CALL from there, but that would require adding
a JMP in the non-faulting path to avoid calling kvm_spurious_fault()
and would add no value, i.e. the stack trace would be the same.
Using CALL:
------------[ cut here ]------------
kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356!
invalid opcode: 0000 [#1] SMP
CPU: 4 PID: 1057 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm]
Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41
RSP: 0018:ffffc900004bbcc8 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888273fd8000 R08: 00000000000003e8 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000371fb0
R13: 0000000000000000 R14: 000000026d763cf4 R15: ffff888273fd8000
FS: 00007f3d69691700(0000) GS:ffff888277800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f89bc56fe0 CR3: 0000000271a5a001 CR4: 0000000000362ee0
Call Trace:
free_kvm_area+0x1044/0x43ea [kvm_intel]
? vmx_vcpu_run+0x156/0x630 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? __set_task_blocked+0x38/0x90
? __set_current_blocked+0x50/0x60
? __fpu__restore_sig+0x97/0x490
? do_vfs_ioctl+0xa1/0x620
? __x64_sys_futex+0x89/0x180
? ksys_ioctl+0x66/0x70
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x4f/0x100
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc
---[ end trace 9775b14b123b1713 ]---
Using JMP:
------------[ cut here ]------------
kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356!
invalid opcode: 0000 [#1] SMP
CPU: 6 PID: 1067 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm]
Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41
RSP: 0018:ffffc90000497cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88827058bd40 R08: 00000000000003e8 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000369fb0
R13: 0000000000000000 R14: 00000003c8fc6642 R15: ffff88827058bd40
FS: 00007f3d7219e700(0000) GS:ffff888277900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3d64001000 CR3: 0000000271c6b004 CR4: 0000000000362ee0
Call Trace:
vmx_vcpu_run+0x156/0x630 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? __set_task_blocked+0x38/0x90
? __set_current_blocked+0x50/0x60
? __fpu__restore_sig+0x97/0x490
? do_vfs_ioctl+0xa1/0x620
? __x64_sys_futex+0x89/0x180
? ksys_ioctl+0x66/0x70
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x4f/0x100
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc
---[ end trace f9daedb85ab3ddba ]---
Fixes: b7c4145ba2eb ("KVM: Don't spin on virt instruction faults during reboot")
Cc: [email protected]
Signed-off-by: Sean Christopherson <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/include/asm/kvm_host.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/x86/include/asm/kvm_host.h
+++ b/arch/x86/include/asm/kvm_host.h
@@ -1441,7 +1441,7 @@ asmlinkage void kvm_spurious_fault(void)
"cmpb $0, kvm_rebooting \n\t" \
"jne 668b \n\t" \
__ASM_SIZE(push) " $666b \n\t" \
- "call kvm_spurious_fault \n\t" \
+ "jmp kvm_spurious_fault \n\t" \
".popsection \n\t" \
_ASM_EXTABLE(666b, 667b)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Shalom Toledo <[email protected]>
[ Upstream commit cf0b70e71b32137ccf9c1f3dd9fb30cbf89b4322 ]
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f433f ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: Shalom Toledo <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlxsw/core.c | 19 ++++++++++++++++++-
drivers/net/ethernet/mellanox/mlxsw/core.h | 3 +++
drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 7 ++++++-
3 files changed, 27 insertions(+), 2 deletions(-)
--- a/drivers/net/ethernet/mellanox/mlxsw/core.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/core.c
@@ -81,6 +81,7 @@ struct mlxsw_core {
struct mlxsw_core_port *ports;
unsigned int max_ports;
bool reload_fail;
+ bool fw_flash_in_progress;
unsigned long driver_priv[0];
/* driver_priv has to be always the last item */
};
@@ -428,12 +429,16 @@ struct mlxsw_reg_trans {
struct rcu_head rcu;
};
-#define MLXSW_EMAD_TIMEOUT_MS 200
+#define MLXSW_EMAD_TIMEOUT_DURING_FW_FLASH_MS 3000
+#define MLXSW_EMAD_TIMEOUT_MS 200
static void mlxsw_emad_trans_timeout_schedule(struct mlxsw_reg_trans *trans)
{
unsigned long timeout = msecs_to_jiffies(MLXSW_EMAD_TIMEOUT_MS);
+ if (trans->core->fw_flash_in_progress)
+ timeout = msecs_to_jiffies(MLXSW_EMAD_TIMEOUT_DURING_FW_FLASH_MS);
+
queue_delayed_work(trans->core->emad_wq, &trans->timeout_dw, timeout);
}
@@ -1854,6 +1859,18 @@ int mlxsw_core_kvd_sizes_get(struct mlxs
}
EXPORT_SYMBOL(mlxsw_core_kvd_sizes_get);
+void mlxsw_core_fw_flash_start(struct mlxsw_core *mlxsw_core)
+{
+ mlxsw_core->fw_flash_in_progress = true;
+}
+EXPORT_SYMBOL(mlxsw_core_fw_flash_start);
+
+void mlxsw_core_fw_flash_end(struct mlxsw_core *mlxsw_core)
+{
+ mlxsw_core->fw_flash_in_progress = false;
+}
+EXPORT_SYMBOL(mlxsw_core_fw_flash_end);
+
static int __init mlxsw_core_module_init(void)
{
int err;
--- a/drivers/net/ethernet/mellanox/mlxsw/core.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/core.h
@@ -292,6 +292,9 @@ int mlxsw_core_kvd_sizes_get(struct mlxs
u64 *p_single_size, u64 *p_double_size,
u64 *p_linear_size);
+void mlxsw_core_fw_flash_start(struct mlxsw_core *mlxsw_core);
+void mlxsw_core_fw_flash_end(struct mlxsw_core *mlxsw_core);
+
bool mlxsw_core_res_valid(struct mlxsw_core *mlxsw_core,
enum mlxsw_res_id res_id);
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -308,8 +308,13 @@ static int mlxsw_sp_firmware_flash(struc
},
.mlxsw_sp = mlxsw_sp
};
+ int err;
- return mlxfw_firmware_flash(&mlxsw_sp_mlxfw_dev.mlxfw_dev, firmware);
+ mlxsw_core_fw_flash_start(mlxsw_sp->core);
+ err = mlxfw_firmware_flash(&mlxsw_sp_mlxfw_dev.mlxfw_dev, firmware);
+ mlxsw_core_fw_flash_end(mlxsw_sp->core);
+
+ return err;
}
static int mlxsw_sp_fw_rev_validate(struct mlxsw_sp *mlxsw_sp)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Diana Craciun <[email protected]>
commit 7d8bad99ba5a22892f0cad6881289fdc3875a930 upstream.
Currently for CONFIG_PPC_FSL_BOOK3E the spectre_v2 file is incorrect:
$ cat /sys/devices/system/cpu/vulnerabilities/spectre_v2
"Mitigation: Software count cache flush"
Which is wrong. Fix it to report vulnerable for now.
Fixes: ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: [email protected] # v4.19+
Signed-off-by: Diana Craciun <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/powerpc/kernel/security.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/powerpc/kernel/security.c
+++ b/arch/powerpc/kernel/security.c
@@ -22,7 +22,7 @@ enum count_cache_flush_type {
COUNT_CACHE_FLUSH_SW = 0x2,
COUNT_CACHE_FLUSH_HW = 0x4,
};
-static enum count_cache_flush_type count_cache_flush_type;
+static enum count_cache_flush_type count_cache_flush_type = COUNT_CACHE_FLUSH_NONE;
bool barrier_nospec_enabled;
static bool no_nospec;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sean Christopherson <[email protected]>
commit 1b3ab5ad1b8ad99bae76ec583809c5f5a31c707c upstream.
Fixes: 34a1cd60d17f ("kvm: x86: vmx: move some vmx setting from vmx_init() to hardware_setup()")
Cc: [email protected]
Signed-off-by: Sean Christopherson <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/x86/kvm/vmx.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -8011,13 +8011,16 @@ static __init int hardware_setup(void)
kvm_mce_cap_supported |= MCG_LMCE_P;
- return alloc_kvm_area();
+ r = alloc_kvm_area();
+ if (r)
+ goto out;
+ return 0;
out:
for (i = 0; i < VMX_BITMAP_NR; i++)
free_page((unsigned long)vmx_bitmap[i]);
- return r;
+ return r;
}
static __exit void hardware_unsetup(void)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alexey Brodkin <[email protected]>
commit bf287607c80f24387fedb431a346dc67f25be12c upstream.
It turned out we used to use default implementation of sched_clock()
from kernel/sched/clock.c which was as precise as 1/HZ, i.e.
by default we had 10 msec granularity of time measurement.
Now given ARC built-in timers are clocked with the same frequency as
CPU cores we may get much higher precision of time tracking.
Thus we switch to generic sched_clock which really reads ARC hardware
counters.
This is especially helpful for measuring short events.
That's what we used to have:
------------------------------>8------------------------
$ perf stat /bin/sh -c /root/lmbench-master/bin/arc/hello > /dev/null
Performance counter stats for '/bin/sh -c /root/lmbench-master/bin/arc/hello':
10.000000 task-clock (msec) # 2.832 CPUs utilized
1 context-switches # 0.100 K/sec
1 cpu-migrations # 0.100 K/sec
63 page-faults # 0.006 M/sec
3049480 cycles # 0.305 GHz
1091259 instructions # 0.36 insn per cycle
256828 branches # 25.683 M/sec
27026 branch-misses # 10.52% of all branches
0.003530687 seconds time elapsed
0.000000000 seconds user
0.010000000 seconds sys
------------------------------>8------------------------
And now we'll see:
------------------------------>8------------------------
$ perf stat /bin/sh -c /root/lmbench-master/bin/arc/hello > /dev/null
Performance counter stats for '/bin/sh -c /root/lmbench-master/bin/arc/hello':
3.004322 task-clock (msec) # 0.865 CPUs utilized
1 context-switches # 0.333 K/sec
1 cpu-migrations # 0.333 K/sec
63 page-faults # 0.021 M/sec
2986734 cycles # 0.994 GHz
1087466 instructions # 0.36 insn per cycle
255209 branches # 84.947 M/sec
26002 branch-misses # 10.19% of all branches
0.003474829 seconds time elapsed
0.003519000 seconds user
0.000000000 seconds sys
------------------------------>8------------------------
Note how much more meaningful is the second output - time spent for
execution pretty much matches number of cycles spent (we're runnign
@ 1GHz here).
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Daniel Lezcano <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Acked-by: Vineet Gupta <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arc/Kconfig | 1 +
drivers/clocksource/Kconfig | 1 +
drivers/clocksource/arc_timer.c | 22 ++++++++++++++++++++++
3 files changed, 24 insertions(+)
--- a/arch/arc/Kconfig
+++ b/arch/arc/Kconfig
@@ -26,6 +26,7 @@ config ARC
select GENERIC_IRQ_SHOW
select GENERIC_PCI_IOMAP
select GENERIC_PENDING_IRQ if SMP
+ select GENERIC_SCHED_CLOCK
select GENERIC_SMP_IDLE_THREAD
select HAVE_ARCH_KGDB
select HAVE_ARCH_TRACEHOOK
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -290,6 +290,7 @@ config CLKSRC_MPS2
config ARC_TIMERS
bool "Support for 32-bit TIMERn counters in ARC Cores" if COMPILE_TEST
+ depends on GENERIC_SCHED_CLOCK
select TIMER_OF
help
These are legacy 32-bit TIMER0 and TIMER1 counters found on all ARC cores
--- a/drivers/clocksource/arc_timer.c
+++ b/drivers/clocksource/arc_timer.c
@@ -23,6 +23,7 @@
#include <linux/cpu.h>
#include <linux/of.h>
#include <linux/of_irq.h>
+#include <linux/sched_clock.h>
#include <soc/arc/timers.h>
#include <soc/arc/mcip.h>
@@ -88,6 +89,11 @@ static u64 arc_read_gfrc(struct clocksou
return (((u64)h) << 32) | l;
}
+static notrace u64 arc_gfrc_clock_read(void)
+{
+ return arc_read_gfrc(NULL);
+}
+
static struct clocksource arc_counter_gfrc = {
.name = "ARConnect GFRC",
.rating = 400,
@@ -111,6 +117,8 @@ static int __init arc_cs_setup_gfrc(stru
if (ret)
return ret;
+ sched_clock_register(arc_gfrc_clock_read, 64, arc_timer_freq);
+
return clocksource_register_hz(&arc_counter_gfrc, arc_timer_freq);
}
TIMER_OF_DECLARE(arc_gfrc, "snps,archs-timer-gfrc", arc_cs_setup_gfrc);
@@ -139,6 +147,11 @@ static u64 arc_read_rtc(struct clocksour
return (((u64)h) << 32) | l;
}
+static notrace u64 arc_rtc_clock_read(void)
+{
+ return arc_read_rtc(NULL);
+}
+
static struct clocksource arc_counter_rtc = {
.name = "ARCv2 RTC",
.rating = 350,
@@ -170,6 +183,8 @@ static int __init arc_cs_setup_rtc(struc
write_aux_reg(AUX_RTC_CTRL, 1);
+ sched_clock_register(arc_rtc_clock_read, 64, arc_timer_freq);
+
return clocksource_register_hz(&arc_counter_rtc, arc_timer_freq);
}
TIMER_OF_DECLARE(arc_rtc, "snps,archs-timer-rtc", arc_cs_setup_rtc);
@@ -185,6 +200,11 @@ static u64 arc_read_timer1(struct clocks
return (u64) read_aux_reg(ARC_REG_TIMER1_CNT);
}
+static notrace u64 arc_timer1_clock_read(void)
+{
+ return arc_read_timer1(NULL);
+}
+
static struct clocksource arc_counter_timer1 = {
.name = "ARC Timer1",
.rating = 300,
@@ -209,6 +229,8 @@ static int __init arc_cs_setup_timer1(st
write_aux_reg(ARC_REG_TIMER1_CNT, 0);
write_aux_reg(ARC_REG_TIMER1_CTRL, TIMER_CTRL_NH);
+ sched_clock_register(arc_timer1_clock_read, 32, arc_timer_freq);
+
return clocksource_register_hz(&arc_counter_timer1, arc_timer_freq);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Miquel Raynal <[email protected]>
commit cafb56dd741e61c99709bcd2b193a9a1d36def3b upstream.
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: [email protected]
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/mtd/nand/raw/marvell_nand.c | 17 ++++++++++++++---
1 file changed, 14 insertions(+), 3 deletions(-)
--- a/drivers/mtd/nand/raw/marvell_nand.c
+++ b/drivers/mtd/nand/raw/marvell_nand.c
@@ -444,9 +444,14 @@ static void marvell_nfc_enable_int(struc
writel_relaxed(reg & ~int_mask, nfc->regs + NDCR);
}
-static void marvell_nfc_clear_int(struct marvell_nfc *nfc, u32 int_mask)
+static u32 marvell_nfc_clear_int(struct marvell_nfc *nfc, u32 int_mask)
{
+ u32 reg;
+
+ reg = readl_relaxed(nfc->regs + NDSR);
writel_relaxed(int_mask, nfc->regs + NDSR);
+
+ return reg & int_mask;
}
static void marvell_nfc_force_byte_access(struct nand_chip *chip,
@@ -613,6 +618,7 @@ static int marvell_nfc_wait_cmdd(struct
static int marvell_nfc_wait_op(struct nand_chip *chip, unsigned int timeout_ms)
{
struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
+ u32 pending;
int ret;
/* Timeout is expressed in ms */
@@ -625,8 +631,13 @@ static int marvell_nfc_wait_op(struct na
ret = wait_for_completion_timeout(&nfc->complete,
msecs_to_jiffies(timeout_ms));
marvell_nfc_disable_int(nfc, NDCR_RDYM);
- marvell_nfc_clear_int(nfc, NDSR_RDY(0) | NDSR_RDY(1));
- if (!ret) {
+ pending = marvell_nfc_clear_int(nfc, NDSR_RDY(0) | NDSR_RDY(1));
+
+ /*
+ * In case the interrupt was not served in the required time frame,
+ * check if the ISR was not served or if something went actually wrong.
+ */
+ if (ret && !pending) {
dev_err(nfc->dev, "Timeout waiting for RB signal\n");
return -ETIMEDOUT;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Arnd Bergmann <[email protected]>
commit 2a9d92fb3a1282a4659f1bb6d5684018846537b7 upstream.
I ran into a link-time error with the atmel-quadspi driver on the
EBSA110 platform:
drivers/mtd/built-in.o: In function `atmel_qspi_run_command':
:(.text+0x1ee3c): undefined reference to `_memcpy_toio'
:(.text+0x1ee48): undefined reference to `_memcpy_fromio'
The problem is that _memcpy_toio/_memcpy_fromio are not available on
that platform, and we have to prevent building the driver there.
In case we want to backport this to older kernels: between linux-4.8
and linux-4.20, the Kconfig entry was in drivers/mtd/spi-nor/Kconfig
but had the same problem.
Link: https://lore.kernel.org/patchwork/patch/812860/
Fixes: 161aaab8a067 ("mtd: atmel-quadspi: add driver for Atmel QSPI controller")
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/mtd/spi-nor/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -41,7 +41,7 @@ config SPI_ASPEED_SMC
config SPI_ATMEL_QUADSPI
tristate "Atmel Quad SPI Controller"
- depends on ARCH_AT91 || (ARM && COMPILE_TEST)
+ depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
depends on OF && HAS_IOMEM
help
This enables support for the Quad SPI controller in master mode.
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Theodore Ts'o <[email protected]>
commit fde872682e175743e0c3ef939c89e3c6008a1529 upstream.
Some time back, nfsd switched from calling vfs_fsync() to using a new
commit_metadata() hook in export_operations(). If the file system did
not provide a commit_metadata() hook, it fell back to using
sync_inode_metadata(). Unfortunately doesn't work on all file
systems. In particular, it doesn't work on ext4 due to how the inode
gets journalled --- the VFS writeback code will not always call
ext4_write_inode().
So we need to provide our own ext4_nfs_commit_metdata() method which
calls ext4_write_inode() directly.
Google-Bug-Id: 121195940
Signed-off-by: Theodore Ts'o <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/super.c | 11 +++++++++++
include/trace/events/ext4.h | 20 ++++++++++++++++++++
2 files changed, 31 insertions(+)
--- a/fs/ext4/super.c
+++ b/fs/ext4/super.c
@@ -1202,6 +1202,16 @@ static struct dentry *ext4_fh_to_parent(
ext4_nfs_get_inode);
}
+static int ext4_nfs_commit_metadata(struct inode *inode)
+{
+ struct writeback_control wbc = {
+ .sync_mode = WB_SYNC_ALL
+ };
+
+ trace_ext4_nfs_commit_metadata(inode);
+ return ext4_write_inode(inode, &wbc);
+}
+
/*
* Try to release metadata pages (indirect blocks, directories) which are
* mapped via the block device. Since these pages could have journal heads
@@ -1406,6 +1416,7 @@ static const struct export_operations ex
.fh_to_dentry = ext4_fh_to_dentry,
.fh_to_parent = ext4_fh_to_parent,
.get_parent = ext4_get_parent,
+ .commit_metadata = ext4_nfs_commit_metadata,
};
enum {
--- a/include/trace/events/ext4.h
+++ b/include/trace/events/ext4.h
@@ -225,6 +225,26 @@ TRACE_EVENT(ext4_drop_inode,
(unsigned long) __entry->ino, __entry->drop)
);
+TRACE_EVENT(ext4_nfs_commit_metadata,
+ TP_PROTO(struct inode *inode),
+
+ TP_ARGS(inode),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( ino_t, ino )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = inode->i_sb->s_dev;
+ __entry->ino = inode->i_ino;
+ ),
+
+ TP_printk("dev %d,%d ino %lu",
+ MAJOR(__entry->dev), MINOR(__entry->dev),
+ (unsigned long) __entry->ino)
+);
+
TRACE_EVENT(ext4_mark_inode_dirty,
TP_PROTO(struct inode *inode, unsigned long IP),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Adrian Hunter <[email protected]>
commit 225f99e0c811e23836c4911a2ff147e167dd1fe8 upstream.
thread__resolve() is used in the sample_addr_correlates_sym() cases
where 'addr' is a destination of a branch which does not necessarily
have the same cpumode as the 'ip'. Use the fallback function in that
case.
This patch depends on patch "perf tools: Add fallback functions for
cases where cpumode is insufficient".
Signed-off-by: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Leo Yan <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: [email protected] # 4.19
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/util/event.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/tools/perf/util/event.c
+++ b/tools/perf/util/event.c
@@ -1705,7 +1705,7 @@ bool sample_addr_correlates_sym(struct p
void thread__resolve(struct thread *thread, struct addr_location *al,
struct perf_sample *sample)
{
- thread__find_map(thread, sample->cpumode, sample->addr, al);
+ thread__find_map_fb(thread, sample->cpumode, sample->addr, al);
al->cpu = sample->cpu;
al->sym = NULL;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lukas Wunner <[email protected]>
commit e82b0b3828451c1cd331d9f304c6078fcd43b62e upstream.
If a DMA transfer finishes orderly right when spi_transfer_one_message()
determines that it has timed out, the callbacks bcm2835_spi_dma_done()
and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(),
potentially leading to double termination.
Prevent by atomically changing the dma_pending flag before calling
dmaengine_terminate_all().
Signed-off-by: Lukas Wunner <[email protected]>
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: [email protected] # v4.2+
Cc: Mathias Duckeck <[email protected]>
Cc: Frank Pavlic <[email protected]>
Cc: Martin Sperl <[email protected]>
Cc: Noralf Trønnes <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-bcm2835.c | 10 ++++------
1 file changed, 4 insertions(+), 6 deletions(-)
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -233,10 +233,9 @@ static void bcm2835_spi_dma_done(void *d
* is called the tx-dma must have finished - can't get to this
* situation otherwise...
*/
- dmaengine_terminate_all(master->dma_tx);
-
- /* mark as no longer pending */
- bs->dma_pending = 0;
+ if (cmpxchg(&bs->dma_pending, true, false)) {
+ dmaengine_terminate_all(master->dma_tx);
+ }
/* and mark as completed */;
complete(&master->xfer_completion);
@@ -617,10 +616,9 @@ static void bcm2835_spi_handle_err(struc
struct bcm2835_spi *bs = spi_master_get_devdata(master);
/* if an error occurred and we have an active dma, then terminate */
- if (bs->dma_pending) {
+ if (cmpxchg(&bs->dma_pending, true, false)) {
dmaengine_terminate_all(master->dma_tx);
dmaengine_terminate_all(master->dma_rx);
- bs->dma_pending = 0;
}
/* and reset */
bcm2835_spi_reset_hw(master);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: "Allan W. Nielsen" <[email protected]>
[ Upstream commit 8fd1a4affbdafda592f80cd01bf7a382a5ff2fe8 ]
The MAC table in Ocelot supports auto aging (normal) and static entries.
MAC entries that is manually configured should be static and not subject
to aging.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Allan Nielsen <[email protected]>
Reviewed-by: Steen Hegelund <[email protected]>
Signed-off-by: Steen Hegelund <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mscc/ocelot.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/ethernet/mscc/ocelot.c
+++ b/drivers/net/ethernet/mscc/ocelot.c
@@ -733,7 +733,7 @@ static int ocelot_fdb_add(struct ndmsg *
}
return ocelot_mact_learn(ocelot, port->chip_port, addr, vid,
- ENTRYTYPE_NORMAL);
+ ENTRYTYPE_LOCKED);
}
static int ocelot_fdb_del(struct ndmsg *ndm, struct nlattr *tb[],
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Theodore Ts'o <[email protected]>
commit 18f2c4fcebf2582f96cbd5f2238f4f354a0e4847 upstream.
If the file system has been shut down or is read-only, then
ext4_write_inode() needs to bail out early.
Also use jbd2_complete_transaction() instead of ext4_force_commit() so
we only force a commit if it is needed.
Signed-off-by: Theodore Ts'o <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/inode.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -5369,9 +5369,13 @@ int ext4_write_inode(struct inode *inode
{
int err;
- if (WARN_ON_ONCE(current->flags & PF_MEMALLOC))
+ if (WARN_ON_ONCE(current->flags & PF_MEMALLOC) ||
+ sb_rdonly(inode->i_sb))
return 0;
+ if (unlikely(ext4_forced_shutdown(EXT4_SB(inode->i_sb))))
+ return -EIO;
+
if (EXT4_SB(inode->i_sb)->s_journal) {
if (ext4_journal_current_handle()) {
jbd_debug(1, "called recursively, non-PF_MEMALLOC!\n");
@@ -5387,7 +5391,8 @@ int ext4_write_inode(struct inode *inode
if (wbc->sync_mode != WB_SYNC_ALL || wbc->for_sync)
return 0;
- err = ext4_force_commit(inode->i_sb);
+ err = jbd2_complete_transaction(EXT4_SB(inode->i_sb)->s_journal,
+ EXT4_I(inode)->i_sync_tid);
} else {
struct ext4_iloc iloc;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Mantas Mikulėnas <[email protected]>
commit 40906ebe3af6a48457151b3c6726b480f6a6cb13 upstream.
Tested with 4.19.9.
v2: Changed from CXT_FIXUP_MUTE_LED_GPIO to CXT_FIXUP_HP_DOCK because
that's what the existing fixups for EliteBooks use.
Signed-off-by: Mantas Mikulėnas <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/hda/patch_conexant.c | 1 +
1 file changed, 1 insertion(+)
--- a/sound/pci/hda/patch_conexant.c
+++ b/sound/pci/hda/patch_conexant.c
@@ -923,6 +923,7 @@ static const struct snd_pci_quirk cxt506
SND_PCI_QUIRK(0x103c, 0x8079, "HP EliteBook 840 G3", CXT_FIXUP_HP_DOCK),
SND_PCI_QUIRK(0x103c, 0x807C, "HP EliteBook 820 G3", CXT_FIXUP_HP_DOCK),
SND_PCI_QUIRK(0x103c, 0x80FD, "HP ProBook 640 G2", CXT_FIXUP_HP_DOCK),
+ SND_PCI_QUIRK(0x103c, 0x828c, "HP EliteBook 840 G4", CXT_FIXUP_HP_DOCK),
SND_PCI_QUIRK(0x103c, 0x83b3, "HP EliteBook 830 G5", CXT_FIXUP_HP_DOCK),
SND_PCI_QUIRK(0x103c, 0x83d3, "HP ProBook 640 G4", CXT_FIXUP_HP_DOCK),
SND_PCI_QUIRK(0x103c, 0x8174, "HP Spectre x360", CXT_FIXUP_HP_SPECTRE),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: ruippan (潘睿) <[email protected]>
commit e647e29196b7f802f8242c39ecb7cc937f5ef217 upstream.
Commit e2b911c53584 ("ext4: clean up feature test macros with
predicate functions") broke the EXT4_IOC_GROUP_ADD ioctl. This was
not noticed since only very old versions of resize2fs (before
e2fsprogs 1.42) use this ioctl. However, using a new kernel with an
enterprise Linux userspace will cause attempts to use online resize to
fail with "No reserved GDT blocks".
Fixes: e2b911c53584 ("ext4: clean up feature test macros with predicate...")
Cc: [email protected] # v4.4
Signed-off-by: Theodore Ts'o <[email protected]>
Signed-off-by: ruippan (潘睿) <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/resize.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/fs/ext4/resize.c
+++ b/fs/ext4/resize.c
@@ -1631,7 +1631,7 @@ int ext4_group_add(struct super_block *s
}
if (reserved_gdb || gdb_off == 0) {
- if (ext4_has_feature_resize_inode(sb) ||
+ if (!ext4_has_feature_resize_inode(sb) ||
!le16_to_cpu(es->s_reserved_gdt_blocks)) {
ext4_warning(sb,
"No reserved GDT blocks, can't resize");
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dmitry Eremin-Solenikov <[email protected]>
commit 7da66670775d201f633577f5b15a4bbeebaaa2b0 upstream.
Add AES128/192/256-CFB testvectors from NIST SP800-38A.
Signed-off-by: Dmitry Eremin-Solenikov <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Eremin-Solenikov <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
crypto/tcrypt.c | 5 +++
crypto/testmgr.c | 7 +++++
crypto/testmgr.h | 76 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 88 insertions(+)
--- a/crypto/tcrypt.c
+++ b/crypto/tcrypt.c
@@ -1736,6 +1736,7 @@ static int do_test(const char *alg, u32
ret += tcrypt_test("xts(aes)");
ret += tcrypt_test("ctr(aes)");
ret += tcrypt_test("rfc3686(ctr(aes))");
+ ret += tcrypt_test("cfb(aes)");
break;
case 11:
@@ -2062,6 +2063,10 @@ static int do_test(const char *alg, u32
speed_template_16_24_32);
test_cipher_speed("ctr(aes)", DECRYPT, sec, NULL, 0,
speed_template_16_24_32);
+ test_cipher_speed("cfb(aes)", ENCRYPT, sec, NULL, 0,
+ speed_template_16_24_32);
+ test_cipher_speed("cfb(aes)", DECRYPT, sec, NULL, 0,
+ speed_template_16_24_32);
break;
case 201:
--- a/crypto/testmgr.c
+++ b/crypto/testmgr.c
@@ -2685,6 +2685,13 @@ static const struct alg_test_desc alg_te
}
}
}, {
+ .alg = "cfb(aes)",
+ .test = alg_test_skcipher,
+ .fips_allowed = 1,
+ .suite = {
+ .cipher = __VECS(aes_cfb_tv_template)
+ },
+ }, {
.alg = "chacha20",
.test = alg_test_skcipher,
.suite = {
--- a/crypto/testmgr.h
+++ b/crypto/testmgr.h
@@ -11343,6 +11343,82 @@ static const struct cipher_testvec aes_c
},
};
+static const struct cipher_testvec aes_cfb_tv_template[] = {
+ { /* From NIST SP800-38A */
+ .key = "\x2b\x7e\x15\x16\x28\xae\xd2\xa6"
+ "\xab\xf7\x15\x88\x09\xcf\x4f\x3c",
+ .klen = 16,
+ .iv = "\x00\x01\x02\x03\x04\x05\x06\x07"
+ "\x08\x09\x0a\x0b\x0c\x0d\x0e\x0f",
+ .ptext = "\x6b\xc1\xbe\xe2\x2e\x40\x9f\x96"
+ "\xe9\x3d\x7e\x11\x73\x93\x17\x2a"
+ "\xae\x2d\x8a\x57\x1e\x03\xac\x9c"
+ "\x9e\xb7\x6f\xac\x45\xaf\x8e\x51"
+ "\x30\xc8\x1c\x46\xa3\x5c\xe4\x11"
+ "\xe5\xfb\xc1\x19\x1a\x0a\x52\xef"
+ "\xf6\x9f\x24\x45\xdf\x4f\x9b\x17"
+ "\xad\x2b\x41\x7b\xe6\x6c\x37\x10",
+ .ctext = "\x3b\x3f\xd9\x2e\xb7\x2d\xad\x20"
+ "\x33\x34\x49\xf8\xe8\x3c\xfb\x4a"
+ "\xc8\xa6\x45\x37\xa0\xb3\xa9\x3f"
+ "\xcd\xe3\xcd\xad\x9f\x1c\xe5\x8b"
+ "\x26\x75\x1f\x67\xa3\xcb\xb1\x40"
+ "\xb1\x80\x8c\xf1\x87\xa4\xf4\xdf"
+ "\xc0\x4b\x05\x35\x7c\x5d\x1c\x0e"
+ "\xea\xc4\xc6\x6f\x9f\xf7\xf2\xe6",
+ .len = 64,
+ }, {
+ .key = "\x8e\x73\xb0\xf7\xda\x0e\x64\x52"
+ "\xc8\x10\xf3\x2b\x80\x90\x79\xe5"
+ "\x62\xf8\xea\xd2\x52\x2c\x6b\x7b",
+ .klen = 24,
+ .iv = "\x00\x01\x02\x03\x04\x05\x06\x07"
+ "\x08\x09\x0a\x0b\x0c\x0d\x0e\x0f",
+ .ptext = "\x6b\xc1\xbe\xe2\x2e\x40\x9f\x96"
+ "\xe9\x3d\x7e\x11\x73\x93\x17\x2a"
+ "\xae\x2d\x8a\x57\x1e\x03\xac\x9c"
+ "\x9e\xb7\x6f\xac\x45\xaf\x8e\x51"
+ "\x30\xc8\x1c\x46\xa3\x5c\xe4\x11"
+ "\xe5\xfb\xc1\x19\x1a\x0a\x52\xef"
+ "\xf6\x9f\x24\x45\xdf\x4f\x9b\x17"
+ "\xad\x2b\x41\x7b\xe6\x6c\x37\x10",
+ .ctext = "\xcd\xc8\x0d\x6f\xdd\xf1\x8c\xab"
+ "\x34\xc2\x59\x09\xc9\x9a\x41\x74"
+ "\x67\xce\x7f\x7f\x81\x17\x36\x21"
+ "\x96\x1a\x2b\x70\x17\x1d\x3d\x7a"
+ "\x2e\x1e\x8a\x1d\xd5\x9b\x88\xb1"
+ "\xc8\xe6\x0f\xed\x1e\xfa\xc4\xc9"
+ "\xc0\x5f\x9f\x9c\xa9\x83\x4f\xa0"
+ "\x42\xae\x8f\xba\x58\x4b\x09\xff",
+ .len = 64,
+ }, {
+ .key = "\x60\x3d\xeb\x10\x15\xca\x71\xbe"
+ "\x2b\x73\xae\xf0\x85\x7d\x77\x81"
+ "\x1f\x35\x2c\x07\x3b\x61\x08\xd7"
+ "\x2d\x98\x10\xa3\x09\x14\xdf\xf4",
+ .klen = 32,
+ .iv = "\x00\x01\x02\x03\x04\x05\x06\x07"
+ "\x08\x09\x0a\x0b\x0c\x0d\x0e\x0f",
+ .ptext = "\x6b\xc1\xbe\xe2\x2e\x40\x9f\x96"
+ "\xe9\x3d\x7e\x11\x73\x93\x17\x2a"
+ "\xae\x2d\x8a\x57\x1e\x03\xac\x9c"
+ "\x9e\xb7\x6f\xac\x45\xaf\x8e\x51"
+ "\x30\xc8\x1c\x46\xa3\x5c\xe4\x11"
+ "\xe5\xfb\xc1\x19\x1a\x0a\x52\xef"
+ "\xf6\x9f\x24\x45\xdf\x4f\x9b\x17"
+ "\xad\x2b\x41\x7b\xe6\x6c\x37\x10",
+ .ctext = "\xdc\x7e\x84\xbf\xda\x79\x16\x4b"
+ "\x7e\xcd\x84\x86\x98\x5d\x38\x60"
+ "\x39\xff\xed\x14\x3b\x28\xb1\xc8"
+ "\x32\x11\x3c\x63\x31\xe5\x40\x7b"
+ "\xdf\x10\x13\x24\x15\xe5\x4b\x92"
+ "\xa1\x3e\xd0\xa8\x26\x7a\xe2\xf9"
+ "\x75\xa3\x85\x74\x1a\xb9\xce\xf8"
+ "\x20\x31\x62\x3d\x55\xb1\xe4\x71",
+ .len = 64,
+ },
+};
+
static const struct aead_testvec hmac_md5_ecb_cipher_null_enc_tv_template[] = {
{ /* Input data from RFC 2410 Case 1 */
#ifdef __LITTLE_ENDIAN
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Boris Brezillon <[email protected]>
commit 9b432630e0150b777c423fdef6a7b8d17dfa70b6 upstream.
Commit e1e6255c311b ("mtd: rawnand: omap2: convert driver to
nand_scan()") moved part of the init code in the ->attach_chip hook
and at the same time changed the struct device object passed to
dma_request_chan() (&pdev->dev instead of pdev->dev.parent).
Fixes: e1e6255c311b ("mtd: rawnand: omap2: convert driver to nand_scan()")
Reported-by: Alexander Sverdlin <[email protected]>
Cc: <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
Tested-by: Alexander Sverdlin <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/mtd/nand/raw/omap2.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/mtd/nand/raw/omap2.c
+++ b/drivers/mtd/nand/raw/omap2.c
@@ -1938,7 +1938,7 @@ static int omap_nand_attach_chip(struct
case NAND_OMAP_PREFETCH_DMA:
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- info->dma = dma_request_chan(dev, "rxtx");
+ info->dma = dma_request_chan(dev->parent, "rxtx");
if (IS_ERR(info->dma)) {
dev_err(dev, "DMA engine request failed\n");
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Anand Jain <[email protected]>
commit 05c49e6bc1e8866ecfd674ebeeb58cdbff9145c2 upstream.
In a secnario where balance and replace co-exists as below,
- start balance
- pause balance
- start replace
- reboot
and when system restarts, balance resumes first. Then the replace is
attempted to restart but will fail as the EXCL_OP lock is already held
by the balance. If so place the replace state back to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state.
Fixes: 010a47bde9420 ("btrfs: add proper safety check before resuming dev-replace")
CC: [email protected] # 4.18+
Signed-off-by: Anand Jain <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/dev-replace.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/fs/btrfs/dev-replace.c
+++ b/fs/btrfs/dev-replace.c
@@ -900,6 +900,10 @@ int btrfs_resume_dev_replace_async(struc
* dev-replace to start anyway.
*/
if (test_and_set_bit(BTRFS_FS_EXCL_OP, &fs_info->flags)) {
+ btrfs_dev_replace_write_lock(dev_replace);
+ dev_replace->replace_state =
+ BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED;
+ btrfs_dev_replace_write_unlock(dev_replace);
btrfs_info(fs_info,
"cannot resume dev-replace, other exclusive operation running");
return 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Adrian Hunter <[email protected]>
commit 692d0e63324d2954a0c63a812a8588e97023a295 upstream.
Branch stacks do not necessarily have the same cpumode as the 'ip'. Use
the fallback functions in those cases.
This patch depends on patch "perf tools: Add fallback functions for cases
where cpumode is insufficient".
Signed-off-by: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Leo Yan <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: [email protected] # 4.19
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/builtin-script.c | 12 ++++++------
tools/perf/util/scripting-engines/trace-event-python.c | 16 ++++++++--------
2 files changed, 14 insertions(+), 14 deletions(-)
--- a/tools/perf/builtin-script.c
+++ b/tools/perf/builtin-script.c
@@ -727,8 +727,8 @@ static int perf_sample__fprintf_brstack(
if (PRINT_FIELD(DSO)) {
memset(&alf, 0, sizeof(alf));
memset(&alt, 0, sizeof(alt));
- thread__find_map(thread, sample->cpumode, from, &alf);
- thread__find_map(thread, sample->cpumode, to, &alt);
+ thread__find_map_fb(thread, sample->cpumode, from, &alf);
+ thread__find_map_fb(thread, sample->cpumode, to, &alt);
}
printed += fprintf(fp, " 0x%"PRIx64, from);
@@ -774,8 +774,8 @@ static int perf_sample__fprintf_brstacks
from = br->entries[i].from;
to = br->entries[i].to;
- thread__find_symbol(thread, sample->cpumode, from, &alf);
- thread__find_symbol(thread, sample->cpumode, to, &alt);
+ thread__find_symbol_fb(thread, sample->cpumode, from, &alf);
+ thread__find_symbol_fb(thread, sample->cpumode, to, &alt);
printed += symbol__fprintf_symname_offs(alf.sym, &alf, fp);
if (PRINT_FIELD(DSO)) {
@@ -819,11 +819,11 @@ static int perf_sample__fprintf_brstacko
from = br->entries[i].from;
to = br->entries[i].to;
- if (thread__find_map(thread, sample->cpumode, from, &alf) &&
+ if (thread__find_map_fb(thread, sample->cpumode, from, &alf) &&
!alf.map->dso->adjust_symbols)
from = map__map_ip(alf.map, from);
- if (thread__find_map(thread, sample->cpumode, to, &alt) &&
+ if (thread__find_map_fb(thread, sample->cpumode, to, &alt) &&
!alt.map->dso->adjust_symbols)
to = map__map_ip(alt.map, to);
--- a/tools/perf/util/scripting-engines/trace-event-python.c
+++ b/tools/perf/util/scripting-engines/trace-event-python.c
@@ -494,14 +494,14 @@ static PyObject *python_process_brstack(
pydict_set_item_string_decref(pyelem, "cycles",
PyLong_FromUnsignedLongLong(br->entries[i].flags.cycles));
- thread__find_map(thread, sample->cpumode,
- br->entries[i].from, &al);
+ thread__find_map_fb(thread, sample->cpumode,
+ br->entries[i].from, &al);
dsoname = get_dsoname(al.map);
pydict_set_item_string_decref(pyelem, "from_dsoname",
_PyUnicode_FromString(dsoname));
- thread__find_map(thread, sample->cpumode,
- br->entries[i].to, &al);
+ thread__find_map_fb(thread, sample->cpumode,
+ br->entries[i].to, &al);
dsoname = get_dsoname(al.map);
pydict_set_item_string_decref(pyelem, "to_dsoname",
_PyUnicode_FromString(dsoname));
@@ -576,14 +576,14 @@ static PyObject *python_process_brstacks
if (!pyelem)
Py_FatalError("couldn't create Python dictionary");
- thread__find_symbol(thread, sample->cpumode,
- br->entries[i].from, &al);
+ thread__find_symbol_fb(thread, sample->cpumode,
+ br->entries[i].from, &al);
get_symoff(al.sym, &al, true, bf, sizeof(bf));
pydict_set_item_string_decref(pyelem, "from",
_PyUnicode_FromString(bf));
- thread__find_symbol(thread, sample->cpumode,
- br->entries[i].to, &al);
+ thread__find_symbol_fb(thread, sample->cpumode,
+ br->entries[i].to, &al);
get_symoff(al.sym, &al, true, bf, sizeof(bf));
pydict_set_item_string_decref(pyelem, "to",
_PyUnicode_FromString(bf));
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tejun Heo <[email protected]>
commit e9d81a1bc2c48ea9782e3e8b53875f419766ef47 upstream.
CSS_TASK_ITER_PROCS implements process-only iteration by making
css_task_iter_advance() skip tasks which aren't threadgroup leaders;
however, when an iteration is started css_task_iter_start() calls the
inner helper function css_task_iter_advance_css_set() instead of
css_task_iter_advance(). As the helper doesn't have the skip logic,
when the first task to visit is a non-leader thread, it doesn't get
skipped correctly as shown in the following example.
# ps -L 2030
PID LWP TTY STAT TIME COMMAND
2030 2030 pts/0 Sl+ 0:00 ./test-thread
2030 2031 pts/0 Sl+ 0:00 ./test-thread
# mkdir -p /sys/fs/cgroup/x/a/b
# echo threaded > /sys/fs/cgroup/x/a/cgroup.type
# echo threaded > /sys/fs/cgroup/x/a/b/cgroup.type
# echo 2030 > /sys/fs/cgroup/x/a/cgroup.procs
# cat /sys/fs/cgroup/x/a/cgroup.threads
2030
2031
# cat /sys/fs/cgroup/x/cgroup.procs
2030
# echo 2030 > /sys/fs/cgroup/x/a/b/cgroup.threads
# cat /sys/fs/cgroup/x/cgroup.procs
2031
2030
The last read of cgroup.procs is incorrectly showing non-leader 2031
in cgroup.procs output.
This can be fixed by updating css_task_iter_advance() to handle the
first advance and css_task_iters_tart() to call
css_task_iter_advance() instead of the inner helper. After the fix,
the same commands result in the following (correct) result:
# ps -L 2062
PID LWP TTY STAT TIME COMMAND
2062 2062 pts/0 Sl+ 0:00 ./test-thread
2062 2063 pts/0 Sl+ 0:00 ./test-thread
# mkdir -p /sys/fs/cgroup/x/a/b
# echo threaded > /sys/fs/cgroup/x/a/cgroup.type
# echo threaded > /sys/fs/cgroup/x/a/b/cgroup.type
# echo 2062 > /sys/fs/cgroup/x/a/cgroup.procs
# cat /sys/fs/cgroup/x/a/cgroup.threads
2062
2063
# cat /sys/fs/cgroup/x/cgroup.procs
2062
# echo 2062 > /sys/fs/cgroup/x/a/b/cgroup.threads
# cat /sys/fs/cgroup/x/cgroup.procs
2062
Signed-off-by: Tejun Heo <[email protected]>
Reported-by: "Michael Kerrisk (man-pages)" <[email protected]>
Fixes: 8cfd8147df67 ("cgroup: implement cgroup v2 thread support")
Cc: [email protected] # v4.14+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
kernel/cgroup/cgroup.c | 33 +++++++++++++++++++--------------
1 file changed, 19 insertions(+), 14 deletions(-)
--- a/kernel/cgroup/cgroup.c
+++ b/kernel/cgroup/cgroup.c
@@ -4186,20 +4186,25 @@ static void css_task_iter_advance(struct
lockdep_assert_held(&css_set_lock);
repeat:
- /*
- * Advance iterator to find next entry. cset->tasks is consumed
- * first and then ->mg_tasks. After ->mg_tasks, we move onto the
- * next cset.
- */
- next = it->task_pos->next;
-
- if (next == it->tasks_head)
- next = it->mg_tasks_head->next;
-
- if (next == it->mg_tasks_head)
+ if (it->task_pos) {
+ /*
+ * Advance iterator to find next entry. cset->tasks is
+ * consumed first and then ->mg_tasks. After ->mg_tasks,
+ * we move onto the next cset.
+ */
+ next = it->task_pos->next;
+
+ if (next == it->tasks_head)
+ next = it->mg_tasks_head->next;
+
+ if (next == it->mg_tasks_head)
+ css_task_iter_advance_css_set(it);
+ else
+ it->task_pos = next;
+ } else {
+ /* called from start, proceed to the first cset */
css_task_iter_advance_css_set(it);
- else
- it->task_pos = next;
+ }
/* if PROCS, skip over tasks which aren't group leaders */
if ((it->flags & CSS_TASK_ITER_PROCS) && it->task_pos &&
@@ -4239,7 +4244,7 @@ void css_task_iter_start(struct cgroup_s
it->cset_head = it->cset_pos;
- css_task_iter_advance_css_set(it);
+ css_task_iter_advance(it);
spin_unlock_irq(&css_set_lock);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Filipe Manana <[email protected]>
commit be6821f82c3cc36e026f5afd10249988852b35ea upstream.
If we create a snapshot of a snapshot currently being used by a send
operation, we can end up with send failing unexpectedly (returning
-ENOENT error to user space for example). The following diagram shows
how this happens.
CPU 1 CPU2 CPU3
btrfs_ioctl_send()
(...)
create_snapshot()
-> creates snapshot of a
root used by the send
task
btrfs_commit_transaction()
create_pending_snapshot()
__get_inode_info()
btrfs_search_slot()
btrfs_search_slot_get_root()
down_read commit_root_sem
get reference on eb of the
commit root
-> eb with bytenr == X
up_read commit_root_sem
btrfs_cow_block(root node)
btrfs_free_tree_block()
-> creates delayed ref to
free the extent
btrfs_run_delayed_refs()
-> runs the delayed ref,
adds extent to
fs_info->pinned_extents
btrfs_finish_extent_commit()
unpin_extent_range()
-> marks extent as free
in the free space cache
transaction commit finishes
btrfs_start_transaction()
(...)
btrfs_cow_block()
btrfs_alloc_tree_block()
btrfs_reserve_extent()
-> allocates extent at
bytenr == X
btrfs_init_new_buffer(bytenr X)
btrfs_find_create_tree_block()
alloc_extent_buffer(bytenr X)
find_extent_buffer(bytenr X)
-> returns existing eb,
which the send task got
(...)
-> modifies content of the
eb with bytenr == X
-> uses an eb that now
belongs to some other
tree and no more matches
the commit root of the
snapshot, resuts will be
unpredictable
The consequences of this race can be various, and can lead to searches in
the commit root performed by the send task failing unexpectedly (unable to
find inode items, returning -ENOENT to user space, for example) or not
failing because an inode item with the same number was added to the tree
that reused the metadata extent, in which case send can behave incorrectly
in the worst case or just fail later for some reason.
Fix this by performing a copy of the commit root's extent buffer when doing
a search in the context of a send operation.
CC: [email protected] # 4.4.x: 1fc28d8e2e9: Btrfs: move get root out of btrfs_search_slot to a helper
CC: [email protected] # 4.4.x: f9ddfd0592a: Btrfs: remove unused check of skip_locking
CC: [email protected] # 4.4.x
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/ctree.c | 29 +++++++++++++++++++++++------
1 file changed, 23 insertions(+), 6 deletions(-)
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -2624,14 +2624,27 @@ static struct extent_buffer *btrfs_searc
root_lock = BTRFS_READ_LOCK;
if (p->search_commit_root) {
- /* The commit roots are read only so we always do read locks */
- if (p->need_commit_sem)
+ /*
+ * The commit roots are read only so we always do read locks,
+ * and we always must hold the commit_root_sem when doing
+ * searches on them, the only exception is send where we don't
+ * want to block transaction commits for a long time, so
+ * we need to clone the commit root in order to avoid races
+ * with transaction commits that create a snapshot of one of
+ * the roots used by a send operation.
+ */
+ if (p->need_commit_sem) {
down_read(&fs_info->commit_root_sem);
- b = root->commit_root;
- extent_buffer_get(b);
- level = btrfs_header_level(b);
- if (p->need_commit_sem)
+ b = btrfs_clone_extent_buffer(root->commit_root);
up_read(&fs_info->commit_root_sem);
+ if (!b)
+ return ERR_PTR(-ENOMEM);
+
+ } else {
+ b = root->commit_root;
+ extent_buffer_get(b);
+ }
+ level = btrfs_header_level(b);
/*
* Ensure that all callers have set skip_locking when
* p->search_commit_root = 1.
@@ -2757,6 +2770,10 @@ int btrfs_search_slot(struct btrfs_trans
again:
prev_cmp = -1;
b = btrfs_search_slot_get_root(root, p, write_lock_level);
+ if (IS_ERR(b)) {
+ ret = PTR_ERR(b);
+ goto done;
+ }
while (b) {
level = btrfs_header_level(b);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stijn Tintel <[email protected]>
commit 8c892df41500469729e0d662816300196e4f463d upstream.
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150ec7 this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150ec7 ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <[email protected]> # 4.19+
Signed-off-by: Jonas Gorski <[email protected]>
Signed-off-by: Stijn Tintel <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 11 +++++++++--
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h | 2 +-
drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c | 2 +-
3 files changed, 11 insertions(+), 4 deletions(-)
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
@@ -5188,10 +5188,17 @@ static struct cfg80211_ops brcmf_cfg8021
.del_pmk = brcmf_cfg80211_del_pmk,
};
-struct cfg80211_ops *brcmf_cfg80211_get_ops(void)
+struct cfg80211_ops *brcmf_cfg80211_get_ops(struct brcmf_mp_device *settings)
{
- return kmemdup(&brcmf_cfg80211_ops, sizeof(brcmf_cfg80211_ops),
+ struct cfg80211_ops *ops;
+
+ ops = kmemdup(&brcmf_cfg80211_ops, sizeof(brcmf_cfg80211_ops),
GFP_KERNEL);
+
+ if (ops && settings->roamoff)
+ ops->update_connect_params = NULL;
+
+ return ops;
}
struct brcmf_cfg80211_vif *brcmf_alloc_vif(struct brcmf_cfg80211_info *cfg,
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h
@@ -404,7 +404,7 @@ struct brcmf_cfg80211_info *brcmf_cfg802
void brcmf_cfg80211_detach(struct brcmf_cfg80211_info *cfg);
s32 brcmf_cfg80211_up(struct net_device *ndev);
s32 brcmf_cfg80211_down(struct net_device *ndev);
-struct cfg80211_ops *brcmf_cfg80211_get_ops(void);
+struct cfg80211_ops *brcmf_cfg80211_get_ops(struct brcmf_mp_device *settings);
enum nl80211_iftype brcmf_cfg80211_get_iftype(struct brcmf_if *ifp);
struct brcmf_cfg80211_vif *brcmf_alloc_vif(struct brcmf_cfg80211_info *cfg,
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c
@@ -1130,7 +1130,7 @@ int brcmf_attach(struct device *dev, str
brcmf_dbg(TRACE, "Enter\n");
- ops = brcmf_cfg80211_get_ops();
+ ops = brcmf_cfg80211_get_ops(settings);
if (!ops)
return -ENOMEM;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Macpaul Lin <[email protected]>
commit eafb27fa5283599ce6c5492ea18cf636a28222bb upstream.
Mediatek Preloader is a proprietary embedded boot loader for loading
Little Kernel and Linux into device DRAM.
This boot loader also handle firmware update. Mediatek Preloader will be
enumerated as a virtual COM port when the device is connected to Windows
or Linux OS via CDC-ACM class driver. When the USB enumeration has been
done, Mediatek Preloader will send out handshake command "READY" to PC
actively instead of waiting command from the download tool.
Since Linux 4.12, the commit "tty: reset termios state on device
registration" (93857edd9829e144acb6c7e72d593f6e01aead66) causes Mediatek
Preloader receiving some abnoraml command like "READYXX" as it sent.
This will be recognized as an incorrect response. The behavior change
also causes the download handshake fail. This change only affects
subsequent connects if the reconnected device happens to get the same minor
number.
By disabling the ECHO termios flag could avoid this problem. However, it
cannot be done by user space configuration when download tool open
/dev/ttyACM0. This is because the device running Mediatek Preloader will
send handshake command "READY" immediately once the CDC-ACM driver is
ready.
This patch wants to fix above problem by introducing "DISABLE_ECHO"
property in driver_info. When Mediatek Preloader is connected, the
CDC-ACM driver could disable ECHO flag in termios to avoid the problem.
Signed-off-by: Macpaul Lin <[email protected]>
Cc: [email protected]
Reviewed-by: Johan Hovold <[email protected]>
Acked-by: Oliver Neukum <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/class/cdc-acm.c | 10 ++++++++++
drivers/usb/class/cdc-acm.h | 1 +
2 files changed, 11 insertions(+)
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -581,6 +581,13 @@ static int acm_tty_install(struct tty_dr
if (retval)
goto error_init_termios;
+ /*
+ * Suppress initial echoing for some devices which might send data
+ * immediately after acm driver has been installed.
+ */
+ if (acm->quirks & DISABLE_ECHO)
+ tty->termios.c_lflag &= ~ECHO;
+
tty->driver_data = acm;
return 0;
@@ -1672,6 +1679,9 @@ static const struct usb_device_id acm_id
{ USB_DEVICE(0x0e8d, 0x0003), /* FIREFLY, MediaTek Inc; [email protected] */
.driver_info = NO_UNION_NORMAL, /* has no union descriptor */
},
+ { USB_DEVICE(0x0e8d, 0x2000), /* MediaTek Inc Preloader */
+ .driver_info = DISABLE_ECHO, /* DISABLE ECHO in termios flag */
+ },
{ USB_DEVICE(0x0e8d, 0x3329), /* MediaTek Inc GPS */
.driver_info = NO_UNION_NORMAL, /* has no union descriptor */
},
--- a/drivers/usb/class/cdc-acm.h
+++ b/drivers/usb/class/cdc-acm.h
@@ -140,3 +140,4 @@ struct acm {
#define QUIRK_CONTROL_LINE_STATE BIT(6)
#define CLEAR_HALT_CONDITIONS BIT(7)
#define SEND_ZERO_PACKET BIT(8)
+#define DISABLE_ECHO BIT(9)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
commit 55e56f06ed71d9441f3abd5b1d3c1a870812b3fe upstream.
After we drop the i_pages lock, the inode can be freed at any time.
The get_unlocked_entry() code has no choice but to reacquire the lock,
so it can't be used here. Create a new wait_entry_unlocked() which takes
care not to acquire the lock or dereference the address_space in any way.
Fixes: c2a7d2a11552 ("filesystem-dax: Introduce dax_lock_mapping_entry()")
Cc: <[email protected]>
Signed-off-by: Matthew Wilcox <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/dax.c | 69 ++++++++++++++++++++++++++------------------------------
1 file changed, 32 insertions(+), 37 deletions(-)
diff --git a/fs/dax.c b/fs/dax.c
index 3a2682a6c832..415605fafaeb 100644
--- a/fs/dax.c
+++ b/fs/dax.c
@@ -229,8 +229,8 @@ static void put_unlocked_mapping_entry(struct address_space *mapping,
*
* Must be called with the i_pages lock held.
*/
-static void *__get_unlocked_mapping_entry(struct address_space *mapping,
- pgoff_t index, void ***slotp, bool (*wait_fn)(void))
+static void *get_unlocked_mapping_entry(struct address_space *mapping,
+ pgoff_t index, void ***slotp)
{
void *entry, **slot;
struct wait_exceptional_entry_queue ewait;
@@ -240,8 +240,6 @@ static void *__get_unlocked_mapping_entry(struct address_space *mapping,
ewait.wait.func = wake_exceptional_entry_func;
for (;;) {
- bool revalidate;
-
entry = __radix_tree_lookup(&mapping->i_pages, index, NULL,
&slot);
if (!entry ||
@@ -256,30 +254,39 @@ static void *__get_unlocked_mapping_entry(struct address_space *mapping,
prepare_to_wait_exclusive(wq, &ewait.wait,
TASK_UNINTERRUPTIBLE);
xa_unlock_irq(&mapping->i_pages);
- revalidate = wait_fn();
+ schedule();
finish_wait(wq, &ewait.wait);
xa_lock_irq(&mapping->i_pages);
- if (revalidate) {
- put_unlocked_mapping_entry(mapping, index, entry);
- return ERR_PTR(-EAGAIN);
- }
}
}
-static bool entry_wait(void)
+/*
+ * The only thing keeping the address space around is the i_pages lock
+ * (it's cycled in clear_inode() after removing the entries from i_pages)
+ * After we call xas_unlock_irq(), we cannot touch xas->xa.
+ */
+static void wait_entry_unlocked(struct address_space *mapping, pgoff_t index,
+ void ***slotp, void *entry)
{
+ struct wait_exceptional_entry_queue ewait;
+ wait_queue_head_t *wq;
+
+ init_wait(&ewait.wait);
+ ewait.wait.func = wake_exceptional_entry_func;
+
+ wq = dax_entry_waitqueue(mapping, index, entry, &ewait.key);
+ prepare_to_wait_exclusive(wq, &ewait.wait, TASK_UNINTERRUPTIBLE);
+ xa_unlock_irq(&mapping->i_pages);
schedule();
+ finish_wait(wq, &ewait.wait);
+
/*
- * Never return an ERR_PTR() from
- * __get_unlocked_mapping_entry(), just keep looping.
+ * Entry lock waits are exclusive. Wake up the next waiter since
+ * we aren't sure we will acquire the entry lock and thus wake
+ * the next waiter up on unlock.
*/
- return false;
-}
-
-static void *get_unlocked_mapping_entry(struct address_space *mapping,
- pgoff_t index, void ***slotp)
-{
- return __get_unlocked_mapping_entry(mapping, index, slotp, entry_wait);
+ if (waitqueue_active(wq))
+ __wake_up(wq, TASK_NORMAL, 1, &ewait.key);
}
static void unlock_mapping_entry(struct address_space *mapping, pgoff_t index)
@@ -398,19 +405,6 @@ static struct page *dax_busy_page(void *entry)
return NULL;
}
-static bool entry_wait_revalidate(void)
-{
- rcu_read_unlock();
- schedule();
- rcu_read_lock();
-
- /*
- * Tell __get_unlocked_mapping_entry() to take a break, we need
- * to revalidate page->mapping after dropping locks
- */
- return true;
-}
-
bool dax_lock_mapping_entry(struct page *page)
{
pgoff_t index;
@@ -446,14 +440,15 @@ bool dax_lock_mapping_entry(struct page *page)
}
index = page->index;
- entry = __get_unlocked_mapping_entry(mapping, index, &slot,
- entry_wait_revalidate);
+ entry = __radix_tree_lookup(&mapping->i_pages, index,
+ NULL, &slot);
if (!entry) {
xa_unlock_irq(&mapping->i_pages);
break;
- } else if (IS_ERR(entry)) {
- xa_unlock_irq(&mapping->i_pages);
- WARN_ON_ONCE(PTR_ERR(entry) != -EAGAIN);
+ } else if (slot_locked(mapping, slot)) {
+ rcu_read_unlock();
+ wait_entry_unlocked(mapping, index, &slot, entry);
+ rcu_read_lock();
continue;
}
lock_slot(mapping, slot);
--
2.19.1
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Martin Blumenstingl <[email protected]>
commit 88960068f25fcc3759455d85460234dcc9d43fef upstream.
Treat "block_count" from struct f2fs_super_block as 64-bit little endian
value in sanity_check_raw_super() because struct f2fs_super_block
declares "block_count" as "__le64".
This fixes a bug where the superblock validation fails on big endian
devices with the following error:
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
As result of this the partition cannot be mounted.
With this patch applied the superblock validation works fine and the
partition can be mounted again:
F2FS-fs (sda1): Mounted with checkpoint version = 7c84
My little endian x86-64 hardware was able to mount the partition without
this fix.
To confirm that mounting f2fs filesystems works on big endian machines
again I tested this on a 32-bit MIPS big endian (lantiq) device.
Fixes: 0cfe75c5b01199 ("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
Cc: [email protected]
Signed-off-by: Martin Blumenstingl <[email protected]>
Reviewed-by: Chao Yu <[email protected]>
Signed-off-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/f2fs/super.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/fs/f2fs/super.c
+++ b/fs/f2fs/super.c
@@ -2267,10 +2267,10 @@ static int sanity_check_raw_super(struct
return 1;
}
- if (segment_count > (le32_to_cpu(raw_super->block_count) >> 9)) {
+ if (segment_count > (le64_to_cpu(raw_super->block_count) >> 9)) {
f2fs_msg(sb, KERN_INFO,
- "Wrong segment_count / block_count (%u > %u)",
- segment_count, le32_to_cpu(raw_super->block_count));
+ "Wrong segment_count / block_count (%u > %llu)",
+ segment_count, le64_to_cpu(raw_super->block_count));
return 1;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Arnaldo Carvalho de Melo <[email protected]>
commit 804234f27180dcf9a25cb98a88d5212f65b7f3fd upstream.
We'll set a new machine field based on env->arch, which for live mode,
like with 'perf top' means we need to use uname() to figure the name of
the arch, fix perf_env__arch() to consider both (env == NULL) and
(env->arch == NULL) as local operation.
Cc: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Leo Yan <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Cc: [email protected] # 4.19
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/util/env.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/tools/perf/util/env.c
+++ b/tools/perf/util/env.c
@@ -166,7 +166,7 @@ const char *perf_env__arch(struct perf_e
struct utsname uts;
char *arch_name;
- if (!env) { /* Assume local operation */
+ if (!env || !env->arch) { /* Assume local operation */
if (uname(&uts) < 0)
return NULL;
arch_name = uts.machine;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Greg Kurz <[email protected]>
commit e1e71e201703500f708bdeaf64660a2a178cb6a0 upstream.
All fields in the PE are big-endian. Use cpu_to_be32() like everywhere
else something is written to the PE. Otherwise a wrong TID will be used
by the NPU. If this TID happens to point to an existing thread sharing
the same mm, it could be woken up by error. This is highly improbable
though. The likely outcome of this is the NPU not finding the target
thread and forcing the AFU into sending an interrupt, which userspace
is supposed to handle anyway.
Fixes: e948e06fc63a ("ocxl: Expose the thread_id needed for wait on POWER9")
Cc: [email protected] # v4.18
Signed-off-by: Greg Kurz <[email protected]>
Acked-by: Andrew Donnellan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/ocxl/link.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/misc/ocxl/link.c
+++ b/drivers/misc/ocxl/link.c
@@ -566,7 +566,7 @@ int ocxl_link_update_pe(void *link_handl
mutex_lock(&spa->spa_lock);
- pe->tid = tid;
+ pe->tid = cpu_to_be32(tid);
/*
* The barrier makes sure the PE is updated
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Greg Kurz <[email protected]>
commit 2f07229f02d4c55affccd11a61af4fd4b94dc436 upstream.
The AFU Descriptor Template in the PCI config space has a Name Space
field which is a 24 Byte ASCII character string of descriptive name
space for the AFU. The OCXL driver read the string four characters at
a time with pci_read_config_dword().
This optimization is valid on a little-endian system since this is PCI,
but a big-endian system ends up with each subset of four characters in
reverse order.
This could be fixed by switching to read characters one by one. Another
option is to swap the bytes if we're big-endian.
Go for the latter with le32_to_cpu().
Cc: [email protected] # v4.16
Signed-off-by: Greg Kurz <[email protected]>
Acked-by: Frederic Barrat <[email protected]>
Acked-by: Andrew Donnellan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/misc/ocxl/config.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/misc/ocxl/config.c
+++ b/drivers/misc/ocxl/config.c
@@ -318,7 +318,7 @@ static int read_afu_name(struct pci_dev
if (rc)
return rc;
ptr = (u32 *) &afu->name[i];
- *ptr = val;
+ *ptr = le32_to_cpu((__force __le32) val);
}
afu->name[OCXL_AFU_NAME_SZ - 1] = '\0'; /* play safe */
return 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Filipe Manana <[email protected]>
commit 41bd60676923822de1df2c50b3f9a10171f4338a upstream.
The log tree has a long standing problem that when a file is fsync'ed we
only check for new ancestors, created in the current transaction, by
following only the hard link for which the fsync was issued. We follow the
ancestors using the VFS' dget_parent() API. This means that if we create a
new link for a file in a directory that is new (or in an any other new
ancestor directory) and then fsync the file using an old hard link, we end
up not logging the new ancestor, and on log replay that new hard link and
ancestor do not exist. In some cases, involving renames, the file will not
exist at all.
Example:
mkfs.btrfs -f /dev/sdb
mount /dev/sdb /mnt
mkdir /mnt/A
touch /mnt/foo
ln /mnt/foo /mnt/A/bar
xfs_io -c fsync /mnt/foo
<power failure>
In this example after log replay only the hard link named 'foo' exists
and directory A does not exist, which is unexpected. In other major linux
filesystems, such as ext4, xfs and f2fs for example, both hard links exist
and so does directory A after mounting again the filesystem.
Checking if any new ancestors are new and need to be logged was added in
2009 by commit 12fcfd22fe5b ("Btrfs: tree logging unlink/rename fixes"),
however only for the ancestors of the hard link (dentry) for which the
fsync was issued, instead of checking for all ancestors for all of the
inode's hard links.
So fix this by tracking the id of the last transaction where a hard link
was created for an inode and then on fsync fallback to a full transaction
commit when an inode has more than one hard link and at least one new hard
link was created in the current transaction. This is the simplest solution
since this is not a common use case (adding frequently hard links for
which there's an ancestor created in the current transaction and then
fsync the file). In case it ever becomes a common use case, a solution
that consists of iterating the fs/subvol btree for each hard link and
check if any ancestor is new, could be implemented.
This solves many unexpected scenarios reported by Jayashree Mohan and
Vijay Chidambaram, and for which there is a new test case for fstests
under review.
Fixes: 12fcfd22fe5b ("Btrfs: tree logging unlink/rename fixes")
CC: [email protected] # 4.4+
Reported-by: Vijay Chidambaram <[email protected]>
Reported-by: Jayashree Mohan <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/btrfs_inode.h | 6 ++++++
fs/btrfs/inode.c | 17 +++++++++++++++++
fs/btrfs/tree-log.c | 16 ++++++++++++++++
3 files changed, 39 insertions(+)
--- a/fs/btrfs/btrfs_inode.h
+++ b/fs/btrfs/btrfs_inode.h
@@ -147,6 +147,12 @@ struct btrfs_inode {
u64 last_unlink_trans;
/*
+ * Track the transaction id of the last transaction used to create a
+ * hard link for the inode. This is used by the log tree (fsync).
+ */
+ u64 last_link_trans;
+
+ /*
* Number of bytes outstanding that are going to need csums. This is
* used in ENOSPC accounting.
*/
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -3689,6 +3689,21 @@ cache_index:
* inode is not a directory, logging its parent unnecessarily.
*/
BTRFS_I(inode)->last_unlink_trans = BTRFS_I(inode)->last_trans;
+ /*
+ * Similar reasoning for last_link_trans, needs to be set otherwise
+ * for a case like the following:
+ *
+ * mkdir A
+ * touch foo
+ * ln foo A/bar
+ * echo 2 > /proc/sys/vm/drop_caches
+ * fsync foo
+ * <power failure>
+ *
+ * Would result in link bar and directory A not existing after the power
+ * failure.
+ */
+ BTRFS_I(inode)->last_link_trans = BTRFS_I(inode)->last_trans;
path->slots[0]++;
if (inode->i_nlink != 1 ||
@@ -6647,6 +6662,7 @@ static int btrfs_link(struct dentry *old
if (err)
goto fail;
}
+ BTRFS_I(inode)->last_link_trans = trans->transid;
d_instantiate(dentry, inode);
ret = btrfs_log_new_name(trans, BTRFS_I(inode), NULL, parent,
true, NULL);
@@ -9175,6 +9191,7 @@ struct inode *btrfs_alloc_inode(struct s
ei->index_cnt = (u64)-1;
ei->dir_index = 0;
ei->last_unlink_trans = 0;
+ ei->last_link_trans = 0;
ei->last_log_commit = 0;
spin_lock_init(&ei->lock);
--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -5781,6 +5781,22 @@ static int btrfs_log_inode_parent(struct
goto end_trans;
}
+ /*
+ * If a new hard link was added to the inode in the current transaction
+ * and its link count is now greater than 1, we need to fallback to a
+ * transaction commit, otherwise we can end up not logging all its new
+ * parents for all the hard links. Here just from the dentry used to
+ * fsync, we can not visit the ancestor inodes for all the other hard
+ * links to figure out if any is new, so we fallback to a transaction
+ * commit (instead of adding a lot of complexity of scanning a btree,
+ * since this scenario is not a common use case).
+ */
+ if (inode->vfs_inode.i_nlink > 1 &&
+ inode->last_link_trans > last_committed) {
+ ret = -EMLINK;
+ goto end_trans;
+ }
+
while (1) {
if (!parent || d_really_is_negative(parent) || sb != parent->d_sb)
break;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Ben Hutchings <[email protected]>
commit 11a64a05dc649815670b1be9fe63d205cb076401 upstream.
Depending on which functions are inlined in util/pmu.c, the snprintf()
calls in perf_pmu__parse_{scale,unit,per_pkg,snapshot}() might trigger a
warning:
util/pmu.c: In function 'pmu_aliases':
util/pmu.c:178:31: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 4095 [-Werror=format-truncation=]
snprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
^~
I found this when trying to build perf from Linux 3.16 with gcc 8.
However I can reproduce the problem in mainline if I force
__perf_pmu__new_alias() to be inlined.
Suppress this by using scnprintf() as has been done elsewhere in perf.
Signed-off-by: Ben Hutchings <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/util/pmu.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
--- a/tools/perf/util/pmu.c
+++ b/tools/perf/util/pmu.c
@@ -145,7 +145,7 @@ static int perf_pmu__parse_scale(struct
int fd, ret = -1;
char path[PATH_MAX];
- snprintf(path, PATH_MAX, "%s/%s.scale", dir, name);
+ scnprintf(path, PATH_MAX, "%s/%s.scale", dir, name);
fd = open(path, O_RDONLY);
if (fd == -1)
@@ -175,7 +175,7 @@ static int perf_pmu__parse_unit(struct p
ssize_t sret;
int fd;
- snprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
+ scnprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
fd = open(path, O_RDONLY);
if (fd == -1)
@@ -205,7 +205,7 @@ perf_pmu__parse_per_pkg(struct perf_pmu_
char path[PATH_MAX];
int fd;
- snprintf(path, PATH_MAX, "%s/%s.per-pkg", dir, name);
+ scnprintf(path, PATH_MAX, "%s/%s.per-pkg", dir, name);
fd = open(path, O_RDONLY);
if (fd == -1)
@@ -223,7 +223,7 @@ static int perf_pmu__parse_snapshot(stru
char path[PATH_MAX];
int fd;
- snprintf(path, PATH_MAX, "%s/%s.snapshot", dir, name);
+ scnprintf(path, PATH_MAX, "%s/%s.snapshot", dir, name);
fd = open(path, O_RDONLY);
if (fd == -1)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lyude Paul <[email protected]>
commit b72c51a58e6d63ef673ac96b8ab5bc98799c5f7b upstream.
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee27f ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <[email protected]>
Cc: Pieter-Paul Giesberts <[email protected]>
Cc: Franky Lin <[email protected]>
Cc: Arend van Spriel <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: Arend Van Spriel <[email protected]>
Cc: Himanshu Jha <[email protected]>
Cc: Dan Haab <[email protected]>
Cc: Jia-Shyr Chuang <[email protected]>
Cc: Ian Molton <[email protected]>
Cc: <[email protected]> # v4.17+
Signed-off-by: Lyude Paul <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
@@ -641,8 +641,9 @@ brcmf_fw_alloc_request(u32 chip, u32 chi
struct brcmf_fw_request *fwreq;
char chipname[12];
const char *mp_path;
+ size_t mp_path_len;
u32 i, j;
- char end;
+ char end = '\0';
size_t reqsz;
for (i = 0; i < table_size; i++) {
@@ -667,7 +668,10 @@ brcmf_fw_alloc_request(u32 chip, u32 chi
mapping_table[i].fw_base, chipname);
mp_path = brcmf_mp_global.firmware_path;
- end = mp_path[strlen(mp_path) - 1];
+ mp_path_len = strnlen(mp_path, BRCMF_FW_ALTPATH_LEN);
+ if (mp_path_len)
+ end = mp_path[mp_path_len - 1];
+
fwreq->n_items = n_fwnames;
for (j = 0; j < n_fwnames; j++) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Paul Burton <[email protected]>
commit ff4dd232ec45a0e45ea69f28f069f2ab22b4908a upstream.
ASIDs have always been stored as unsigned longs, ie. 32 bits on MIPS32
kernels. This is problematic because it is feasible for the ASID version
to overflow & wrap around to zero.
We currently attempt to handle this overflow by simply setting the ASID
version to 1, using asid_first_version(), but we make no attempt to
account for the fact that there may be mm_structs with stale ASIDs that
have versions which we now reuse due to the overflow & wrap around.
Encountering this requires that:
1) A struct mm_struct X is active on CPU A using ASID (V,n).
2) That mm is not used on CPU A for the length of time that it takes
for CPU A's asid_cache to overflow & wrap around to the same
version V that the mm had in step 1. During this time tasks using
the mm could either be sleeping or only scheduled on other CPUs.
3) Some other mm Y becomes active on CPU A and is allocated the same
ASID (V,n).
4) mm X now becomes active on CPU A again, and now incorrectly has the
same ASID as mm Y.
Where struct mm_struct ASIDs are represented above in the format
(version, EntryHi.ASID), and on a typical MIPS32 system version will be
24 bits wide & EntryHi.ASID will be 8 bits wide.
The length of time required in step 2 is highly dependent upon the CPU &
workload, but for a hypothetical 2GHz CPU running a workload which
generates a new ASID every 10000 cycles this period is around 248 days.
Due to this long period of time & the fact that tasks need to be
scheduled in just the right (or wrong, depending upon your inclination)
way, this is obviously a difficult bug to encounter but it's entirely
possible as evidenced by reports.
In order to fix this, simply extend ASIDs to 64 bits even on MIPS32
builds. This will extend the period of time required for the
hypothetical system above to encounter the problem from 28 days to
around 3 trillion years, which feels safely outside of the realms of
possibility.
The cost of this is slightly more generated code in some commonly
executed paths, but this is pretty minimal:
| Code Size Gain | Percentage
-----------------------|----------------|-------------
decstation_defconfig | +270 | +0.00%
32r2el_defconfig | +652 | +0.01%
32r6el_defconfig | +1000 | +0.01%
I have been unable to measure any change in performance of the LMbench
lat_ctx or lat_proc tests resulting from the 64b ASIDs on either
32r2el_defconfig+interAptiv or 32r6el_defconfig+I6500 systems.
Signed-off-by: Paul Burton <[email protected]>
Suggested-by: James Hogan <[email protected]>
References: https://lore.kernel.org/linux-mips/[email protected]/
References: https://lore.kernel.org/linux-mips/[email protected]/
Cc: Jiwei Sun <[email protected]>
Cc: Yu Huabing <[email protected]>
Cc: [email protected] # 2.6.12+
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/include/asm/cpu-info.h | 2 +-
arch/mips/include/asm/mmu.h | 2 +-
arch/mips/include/asm/mmu_context.h | 10 ++++------
arch/mips/mm/c-r3k.c | 2 +-
4 files changed, 7 insertions(+), 9 deletions(-)
--- a/arch/mips/include/asm/cpu-info.h
+++ b/arch/mips/include/asm/cpu-info.h
@@ -50,7 +50,7 @@ struct guest_info {
#define MIPS_CACHE_PINDEX 0x00000020 /* Physically indexed cache */
struct cpuinfo_mips {
- unsigned long asid_cache;
+ u64 asid_cache;
#ifdef CONFIG_MIPS_ASID_BITS_VARIABLE
unsigned long asid_mask;
#endif
--- a/arch/mips/include/asm/mmu.h
+++ b/arch/mips/include/asm/mmu.h
@@ -7,7 +7,7 @@
#include <linux/wait.h>
typedef struct {
- unsigned long asid[NR_CPUS];
+ u64 asid[NR_CPUS];
void *vdso;
atomic_t fp_mode_switching;
--- a/arch/mips/include/asm/mmu_context.h
+++ b/arch/mips/include/asm/mmu_context.h
@@ -76,14 +76,14 @@ extern unsigned long pgd_current[];
* All unused by hardware upper bits will be considered
* as a software asid extension.
*/
-static unsigned long asid_version_mask(unsigned int cpu)
+static inline u64 asid_version_mask(unsigned int cpu)
{
unsigned long asid_mask = cpu_asid_mask(&cpu_data[cpu]);
- return ~(asid_mask | (asid_mask - 1));
+ return ~(u64)(asid_mask | (asid_mask - 1));
}
-static unsigned long asid_first_version(unsigned int cpu)
+static inline u64 asid_first_version(unsigned int cpu)
{
return ~asid_version_mask(cpu) + 1;
}
@@ -102,14 +102,12 @@ static inline void enter_lazy_tlb(struct
static inline void
get_new_mmu_context(struct mm_struct *mm, unsigned long cpu)
{
- unsigned long asid = asid_cache(cpu);
+ u64 asid = asid_cache(cpu);
if (!((asid += cpu_asid_inc()) & cpu_asid_mask(&cpu_data[cpu]))) {
if (cpu_has_vtag_icache)
flush_icache_all();
local_flush_tlb_all(); /* start new asid cycle */
- if (!asid) /* fix version if needed */
- asid = asid_first_version(cpu);
}
cpu_context(cpu, mm) = asid_cache(cpu) = asid;
--- a/arch/mips/mm/c-r3k.c
+++ b/arch/mips/mm/c-r3k.c
@@ -245,7 +245,7 @@ static void r3k_flush_cache_page(struct
pmd_t *pmdp;
pte_t *ptep;
- pr_debug("cpage[%08lx,%08lx]\n",
+ pr_debug("cpage[%08llx,%08lx]\n",
cpu_context(smp_processor_id(), mm), addr);
/* No ASID => no such page in the cache. */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Breno Leitao <[email protected]>
commit e1c3743e1a20647c53b719dbf28b48f45d23f2cd upstream.
On a signal handler return, the user could set a context with MSR[TS] bits
set, and these bits would be copied to task regs->msr.
At restore_tm_sigcontexts(), after current task regs->msr[TS] bits are set,
several __get_user() are called and then a recheckpoint is executed.
This is a problem since a page fault (in kernel space) could happen when
calling __get_user(). If it happens, the process MSR[TS] bits were
already set, but recheckpoint was not executed, and SPRs are still invalid.
The page fault can cause the current process to be de-scheduled, with
MSR[TS] active and without tm_recheckpoint() being called. More
importantly, without TEXASR[FS] bit set also.
Since TEXASR might not have the FS bit set, and when the process is
scheduled back, it will try to reclaim, which will be aborted because of
the CPU is not in the suspended state, and, then, recheckpoint. This
recheckpoint will restore thread->texasr into TEXASR SPR, which might be
zero, hitting a BUG_ON().
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
cpu 0xb: Vector: 700 (Program Check) at [c00000041f1576d0]
pc: c000000000054550: restore_gprs+0xb0/0x180
lr: 0000000000000000
sp: c00000041f157950
msr: 8000000100021033
current = 0xc00000041f143000
paca = 0xc00000000fb86300 softe: 0 irq_happened: 0x01
pid = 1021, comm = kworker/11:1
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
Linux version 4.9.0-3-powerpc64le ([email protected]) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
enter ? for help
[c00000041f157b30] c00000000001bc3c tm_recheckpoint.part.11+0x6c/0xa0
[c00000041f157b70] c00000000001d184 __switch_to+0x1e4/0x4c0
[c00000041f157bd0] c00000000082eeb8 __schedule+0x2f8/0x990
[c00000041f157cb0] c00000000082f598 schedule+0x48/0xc0
[c00000041f157ce0] c0000000000f0d28 worker_thread+0x148/0x610
[c00000041f157d80] c0000000000f96b0 kthread+0x120/0x140
[c00000041f157e30] c00000000000c0e0 ret_from_kernel_thread+0x5c/0x7c
This patch simply delays the MSR[TS] set, so, if there is any page fault in
the __get_user() section, it does not have regs->msr[TS] set, since the TM
structures are still invalid, thus avoiding doing TM operations for
in-kernel exceptions and possible process reschedule.
With this patch, the MSR[TS] will only be set just before recheckpointing
and setting TEXASR[FS] = 1, thus avoiding an interrupt with TM registers in
invalid state.
Other than that, if CONFIG_PREEMPT is set, there might be a preemption just
after setting MSR[TS] and before tm_recheckpoint(), thus, this block must
be atomic from a preemption perspective, thus, calling
preempt_disable/enable() on this code.
It is not possible to move tm_recheckpoint to happen earlier, because it is
required to get the checkpointed registers from userspace, with
__get_user(), thus, the only way to avoid this undesired behavior is
delaying the MSR[TS] set.
The 32-bits signal handler seems to be safe this current issue, but, it
might be exposed to the preemption issue, thus, disabling preemption in
this chunk of code.
Changes from v2:
* Run the critical section with preempt_disable.
Fixes: 87b4e5393af7 ("powerpc/tm: Fix return of active 64bit signals")
Cc: [email protected] (v3.9+)
Signed-off-by: Breno Leitao <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/powerpc/kernel/signal_32.c | 20 +++++++++++++++++-
arch/powerpc/kernel/signal_64.c | 44 +++++++++++++++++++++++++++-------------
2 files changed, 49 insertions(+), 15 deletions(-)
--- a/arch/powerpc/kernel/signal_32.c
+++ b/arch/powerpc/kernel/signal_32.c
@@ -848,7 +848,23 @@ static long restore_tm_user_regs(struct
/* If TM bits are set to the reserved value, it's an invalid context */
if (MSR_TM_RESV(msr_hi))
return 1;
- /* Pull in the MSR TM bits from the user context */
+
+ /*
+ * Disabling preemption, since it is unsafe to be preempted
+ * with MSR[TS] set without recheckpointing.
+ */
+ preempt_disable();
+
+ /*
+ * CAUTION:
+ * After regs->MSR[TS] being updated, make sure that get_user(),
+ * put_user() or similar functions are *not* called. These
+ * functions can generate page faults which will cause the process
+ * to be de-scheduled with MSR[TS] set but without calling
+ * tm_recheckpoint(). This can cause a bug.
+ *
+ * Pull in the MSR TM bits from the user context
+ */
regs->msr = (regs->msr & ~MSR_TS_MASK) | (msr_hi & MSR_TS_MASK);
/* Now, recheckpoint. This loads up all of the checkpointed (older)
* registers, including FP and V[S]Rs. After recheckpointing, the
@@ -873,6 +889,8 @@ static long restore_tm_user_regs(struct
}
#endif
+ preempt_enable();
+
return 0;
}
#endif
--- a/arch/powerpc/kernel/signal_64.c
+++ b/arch/powerpc/kernel/signal_64.c
@@ -467,20 +467,6 @@ static long restore_tm_sigcontexts(struc
if (MSR_TM_RESV(msr))
return -EINVAL;
- /* pull in MSR TS bits from user context */
- regs->msr = (regs->msr & ~MSR_TS_MASK) | (msr & MSR_TS_MASK);
-
- /*
- * Ensure that TM is enabled in regs->msr before we leave the signal
- * handler. It could be the case that (a) user disabled the TM bit
- * through the manipulation of the MSR bits in uc_mcontext or (b) the
- * TM bit was disabled because a sufficient number of context switches
- * happened whilst in the signal handler and load_tm overflowed,
- * disabling the TM bit. In either case we can end up with an illegal
- * TM state leading to a TM Bad Thing when we return to userspace.
- */
- regs->msr |= MSR_TM;
-
/* pull in MSR LE from user context */
regs->msr = (regs->msr & ~MSR_LE) | (msr & MSR_LE);
@@ -572,6 +558,34 @@ static long restore_tm_sigcontexts(struc
tm_enable();
/* Make sure the transaction is marked as failed */
tsk->thread.tm_texasr |= TEXASR_FS;
+
+ /*
+ * Disabling preemption, since it is unsafe to be preempted
+ * with MSR[TS] set without recheckpointing.
+ */
+ preempt_disable();
+
+ /* pull in MSR TS bits from user context */
+ regs->msr = (regs->msr & ~MSR_TS_MASK) | (msr & MSR_TS_MASK);
+
+ /*
+ * Ensure that TM is enabled in regs->msr before we leave the signal
+ * handler. It could be the case that (a) user disabled the TM bit
+ * through the manipulation of the MSR bits in uc_mcontext or (b) the
+ * TM bit was disabled because a sufficient number of context switches
+ * happened whilst in the signal handler and load_tm overflowed,
+ * disabling the TM bit. In either case we can end up with an illegal
+ * TM state leading to a TM Bad Thing when we return to userspace.
+ *
+ * CAUTION:
+ * After regs->MSR[TS] being updated, make sure that get_user(),
+ * put_user() or similar functions are *not* called. These
+ * functions can generate page faults which will cause the process
+ * to be de-scheduled with MSR[TS] set but without calling
+ * tm_recheckpoint(). This can cause a bug.
+ */
+ regs->msr |= MSR_TM;
+
/* This loads the checkpointed FP/VEC state, if used */
tm_recheckpoint(&tsk->thread);
@@ -585,6 +599,8 @@ static long restore_tm_sigcontexts(struc
regs->msr |= MSR_VEC;
}
+ preempt_enable();
+
return err;
}
#endif
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
commit d8a706414af4827fc0b4b1c0c631c607351938b9 upstream.
get_unlocked_entry() uses an exclusive wait because it is guaranteed to
eventually obtain the lock and follow on with an unlock+wakeup cycle.
The wait_entry_unlocked() path does not have the same guarantee. Rather
than open-code an extra wakeup, just switch to a non-exclusive wait.
Cc: Matthew Wilcox <[email protected]>
Reported-by: Linus Torvalds <[email protected]>
Reviewed-by: Jan Kara <[email protected]>
Signed-off-by: Dan Williams <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
---
fs/dax.c | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
diff --git a/fs/dax.c b/fs/dax.c
index 415605fafaeb..09fa70683c41 100644
--- a/fs/dax.c
+++ b/fs/dax.c
@@ -275,18 +275,16 @@ static void wait_entry_unlocked(struct address_space *mapping, pgoff_t index,
ewait.wait.func = wake_exceptional_entry_func;
wq = dax_entry_waitqueue(mapping, index, entry, &ewait.key);
- prepare_to_wait_exclusive(wq, &ewait.wait, TASK_UNINTERRUPTIBLE);
+ /*
+ * Unlike get_unlocked_entry() there is no guarantee that this
+ * path ever successfully retrieves an unlocked entry before an
+ * inode dies. Perform a non-exclusive wait in case this path
+ * never successfully performs its own wake up.
+ */
+ prepare_to_wait(wq, &ewait.wait, TASK_UNINTERRUPTIBLE);
xa_unlock_irq(&mapping->i_pages);
schedule();
finish_wait(wq, &ewait.wait);
-
- /*
- * Entry lock waits are exclusive. Wake up the next waiter since
- * we aren't sure we will acquire the entry lock and thus wake
- * the next waiter up on unlock.
- */
- if (waitqueue_active(wq))
- __wake_up(wq, TASK_NORMAL, 1, &ewait.key);
}
static void unlock_mapping_entry(struct address_space *mapping, pgoff_t index)
--
2.19.1
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Julien Thierry <[email protected]>
commit 2e2f6c3c0b08eed3fcf7de3c7684c940451bdeb1 upstream.
To change the active state of an MMIO, halt is requested for all vcpus of
the affected guest before modifying the IRQ state. This is done by calling
cond_resched_lock() in vgic_mmio_change_active(). However interrupts are
disabled at this point and we cannot reschedule a vcpu.
We actually don't need any of this, as kvm_arm_halt_guest ensures that
all the other vcpus are out of the guest. Let's just drop that useless
code.
Signed-off-by: Julien Thierry <[email protected]>
Suggested-by: Christoffer Dall <[email protected]>
Cc: [email protected]
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
virt/kvm/arm/vgic/vgic-mmio.c | 21 ---------------------
1 file changed, 21 deletions(-)
--- a/virt/kvm/arm/vgic/vgic-mmio.c
+++ b/virt/kvm/arm/vgic/vgic-mmio.c
@@ -313,27 +313,6 @@ static void vgic_mmio_change_active(stru
spin_lock_irqsave(&irq->irq_lock, flags);
- /*
- * If this virtual IRQ was written into a list register, we
- * have to make sure the CPU that runs the VCPU thread has
- * synced back the LR state to the struct vgic_irq.
- *
- * As long as the conditions below are true, we know the VCPU thread
- * may be on its way back from the guest (we kicked the VCPU thread in
- * vgic_change_active_prepare) and still has to sync back this IRQ,
- * so we release and re-acquire the spin_lock to let the other thread
- * sync back the IRQ.
- *
- * When accessing VGIC state from user space, requester_vcpu is
- * NULL, which is fine, because we guarantee that no VCPUs are running
- * when accessing VGIC state from user space so irq->vcpu->cpu is
- * always -1.
- */
- while (irq->vcpu && /* IRQ may have state in an LR somewhere */
- irq->vcpu != requester_vcpu && /* Current thread is not the VCPU thread */
- irq->vcpu->cpu != -1) /* VCPU thread is running */
- cond_resched_lock(&irq->irq_lock);
-
if (irq->hw) {
vgic_hw_irq_change_active(vcpu, irq, active, !requester_vcpu);
} else {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marc Zyngier <[email protected]>
commit bea2ef803ade3359026d5d357348842bca9edcf1 upstream.
SPIs should be checked against the VMs specific configuration, and
not the architectural maximum.
Cc: [email protected]
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
virt/kvm/arm/vgic/vgic.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/virt/kvm/arm/vgic/vgic.c
+++ b/virt/kvm/arm/vgic/vgic.c
@@ -108,8 +108,8 @@ struct vgic_irq *vgic_get_irq(struct kvm
}
/* SPIs */
- if (intid <= VGIC_MAX_SPI) {
- intid = array_index_nospec(intid, VGIC_MAX_SPI);
+ if (intid < (kvm->arch.vgic.nr_spis + VGIC_NR_PRIVATE_IRQS)) {
+ intid = array_index_nospec(intid, kvm->arch.vgic.nr_spis + VGIC_NR_PRIVATE_IRQS);
return &kvm->arch.vgic.spis[intid - VGIC_NR_PRIVATE_IRQS];
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Christoffer Dall <[email protected]>
commit 60c3ab30d8c2ff3a52606df03f05af2aae07dc6b upstream.
When restoring the active state from userspace, we don't know which CPU
was the source for the active state, and this is not architecturally
exposed in any of the register state.
Set the active_source to 0 in this case. In the future, we can expand
on this and exposse the information as additional information to
userspace for GICv2 if anyone cares.
Cc: [email protected]
Signed-off-by: Christoffer Dall <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
virt/kvm/arm/vgic/vgic-mmio.c | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
--- a/virt/kvm/arm/vgic/vgic-mmio.c
+++ b/virt/kvm/arm/vgic/vgic-mmio.c
@@ -317,11 +317,26 @@ static void vgic_mmio_change_active(stru
vgic_hw_irq_change_active(vcpu, irq, active, !requester_vcpu);
} else {
u32 model = vcpu->kvm->arch.vgic.vgic_model;
+ u8 active_source;
irq->active = active;
+
+ /*
+ * The GICv2 architecture indicates that the source CPUID for
+ * an SGI should be provided during an EOI which implies that
+ * the active state is stored somewhere, but at the same time
+ * this state is not architecturally exposed anywhere and we
+ * have no way of knowing the right source.
+ *
+ * This may lead to a VCPU not being able to receive
+ * additional instances of a particular SGI after migration
+ * for a GICv2 VM on some GIC implementations. Oh well.
+ */
+ active_source = (requester_vcpu) ? requester_vcpu->vcpu_id : 0;
+
if (model == KVM_DEV_TYPE_ARM_VGIC_V2 &&
active && vgic_irq_is_sgi(irq->intid))
- irq->active_source = requester_vcpu->vcpu_id;
+ irq->active_source = active_source;
}
if (irq->active)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gustavo A. R. Silva <[email protected]>
commit c23b2e6fc4ca346018618266bcabd335c0a8a49e upstream.
When using the nospec API, it should be taken into account that:
"...if the CPU speculates past the bounds check then
* array_index_nospec() will clamp the index within the range of [0,
* size)."
The above is part of the header for macro array_index_nospec() in
linux/nospec.h
Now, in this particular case, if intid evaluates to exactly VGIC_MAX_SPI
or to exaclty VGIC_MAX_PRIVATE, the array_index_nospec() macro ends up
returning VGIC_MAX_SPI - 1 or VGIC_MAX_PRIVATE - 1 respectively, instead
of VGIC_MAX_SPI or VGIC_MAX_PRIVATE, which, based on the original logic:
/* SGIs and PPIs */
if (intid <= VGIC_MAX_PRIVATE)
return &vcpu->arch.vgic_cpu.private_irqs[intid];
/* SPIs */
if (intid <= VGIC_MAX_SPI)
return &kvm->arch.vgic.spis[intid - VGIC_NR_PRIVATE_IRQS];
are valid values for intid.
Fix this by calling array_index_nospec() macro with VGIC_MAX_PRIVATE + 1
and VGIC_MAX_SPI + 1 as arguments for its parameter size.
Fixes: 41b87599c743 ("KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_get_irq()")
Cc: [email protected]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
[dropped the SPI part which was fixed separately]
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
virt/kvm/arm/vgic/vgic.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/virt/kvm/arm/vgic/vgic.c
+++ b/virt/kvm/arm/vgic/vgic.c
@@ -103,7 +103,7 @@ struct vgic_irq *vgic_get_irq(struct kvm
{
/* SGIs and PPIs */
if (intid <= VGIC_MAX_PRIVATE) {
- intid = array_index_nospec(intid, VGIC_MAX_PRIVATE);
+ intid = array_index_nospec(intid, VGIC_MAX_PRIVATE + 1);
return &vcpu->arch.vgic_cpu.private_irqs[intid];
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Pan Bian <[email protected]>
commit 61157b24e60fb3cd1f85f2c76a7b1d628f970144 upstream.
The function frees qf_inode via iput but then pass qf_inode to
lockdep_set_quota_inode on the failure path. This may result in a
use-after-free bug. The patch frees df_inode only when it is never used.
Fixes: daf647d2dd5 ("ext4: add lockdep annotations for i_data_sem")
Cc: [email protected] # 4.6
Reviewed-by: Jan Kara <[email protected]>
Signed-off-by: Pan Bian <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/super.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/fs/ext4/super.c
+++ b/fs/ext4/super.c
@@ -5712,9 +5712,9 @@ static int ext4_quota_enable(struct supe
qf_inode->i_flags |= S_NOQUOTA;
lockdep_set_quota_inode(qf_inode, I_DATA_SEM_QUOTA);
err = dquot_enable(qf_inode, type, format_id, flags);
- iput(qf_inode);
if (err)
lockdep_set_quota_inode(qf_inode, I_DATA_SEM_NORMAL);
+ iput(qf_inode);
return err;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans Verkuil <[email protected]>
commit ac791f19a273a7fe254a7596f193af6534582a9f upstream.
If the tx_ignore_nack_until_eom error injection was activated,
then tx_nacked was never set instead of setting it when the last
byte of the message was transmitted.
As a result the transmit was marked as OK, when it should have
been NACKed.
Modify the condition so that it always sets tx_nacked when the
last byte of the message was transmitted.
Signed-off-by: Hans Verkuil <[email protected]>
Cc: <[email protected]> # for v4.17 and up
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/cec/cec-pin.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
--- a/drivers/media/cec/cec-pin.c
+++ b/drivers/media/cec/cec-pin.c
@@ -601,8 +601,9 @@ static void cec_pin_tx_states(struct cec
break;
/* Was the message ACKed? */
ack = cec_msg_is_broadcast(&pin->tx_msg) ? v : !v;
- if (!ack && !pin->tx_ignore_nack_until_eom &&
- pin->tx_bit / 10 < pin->tx_msg.len && !pin->tx_post_eom) {
+ if (!ack && (!pin->tx_ignore_nack_until_eom ||
+ pin->tx_bit / 10 == pin->tx_msg.len - 1) &&
+ !pin->tx_post_eom) {
/*
* Note: the CEC spec is ambiguous regarding
* what action to take when a NACK appears
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Georgy A Bystrenin <[email protected]>
commit 9a596f5b39593414c0ec80f71b94a226286f084e upstream.
While resolving a bug with locks on samba shares found a strange behavior.
When a file locked by one node and we trying to lock it from another node
it fail with errno 5 (EIO) but in that case errno must be set to
(EACCES | EAGAIN).
This isn't happening when we try to lock file second time on same node.
In this case it returns EACCES as expected.
Also this issue not reproduces when we use SMB1 protocol (vers=1.0 in
mount options).
Further investigation showed that the mapping from status_to_posix_error
is different for SMB1 and SMB2+ implementations.
For SMB1 mapping is [NT_STATUS_LOCK_NOT_GRANTED to ERRlock]
(See fs/cifs/netmisc.c line 66)
but for SMB2+ mapping is [STATUS_LOCK_NOT_GRANTED to -EIO]
(see fs/cifs/smb2maperror.c line 383)
Quick changes in SMB2+ mapping from EIO to EACCES has fixed issue.
BUG: https://bugzilla.kernel.org/show_bug.cgi?id=201971
Signed-off-by: Georgy A Bystrenin <[email protected]>
Reviewed-by: Pavel Shilovsky <[email protected]>
CC: Stable <[email protected]>
Signed-off-by: Steve French <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/cifs/smb2maperror.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/fs/cifs/smb2maperror.c
+++ b/fs/cifs/smb2maperror.c
@@ -379,8 +379,8 @@ static const struct status_to_posix_erro
{STATUS_NONEXISTENT_EA_ENTRY, -EIO, "STATUS_NONEXISTENT_EA_ENTRY"},
{STATUS_NO_EAS_ON_FILE, -ENODATA, "STATUS_NO_EAS_ON_FILE"},
{STATUS_EA_CORRUPT_ERROR, -EIO, "STATUS_EA_CORRUPT_ERROR"},
- {STATUS_FILE_LOCK_CONFLICT, -EIO, "STATUS_FILE_LOCK_CONFLICT"},
- {STATUS_LOCK_NOT_GRANTED, -EIO, "STATUS_LOCK_NOT_GRANTED"},
+ {STATUS_FILE_LOCK_CONFLICT, -EACCES, "STATUS_FILE_LOCK_CONFLICT"},
+ {STATUS_LOCK_NOT_GRANTED, -EACCES, "STATUS_LOCK_NOT_GRANTED"},
{STATUS_DELETE_PENDING, -ENOENT, "STATUS_DELETE_PENDING"},
{STATUS_CTL_FILE_NOT_SUPPORTED, -ENOSYS,
"STATUS_CTL_FILE_NOT_SUPPORTED"},
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Maciej W. Rozycki <[email protected]>
commit 3cc9ffbb1f51eb4320575a48e4805a8f52e0e26b upstream.
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c3e ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726eb ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
Signed-off-by: Maciej W. Rozycki <[email protected]>
Fixes: 9c6dfed92c3e ("rtc: m41t80: add alarm functionality")
References: 48e9766726eb ("drivers/rtc/rtc-m41t80.c: remove disabled alarm functionality")
Cc: [email protected] # 4.7+
Signed-off-by: Alexandre Belloni <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/rtc/rtc-m41t80.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/rtc/rtc-m41t80.c
+++ b/drivers/rtc/rtc-m41t80.c
@@ -393,7 +393,7 @@ static int m41t80_read_alarm(struct devi
alrm->time.tm_min = bcd2bin(alarmvals[3] & 0x7f);
alrm->time.tm_hour = bcd2bin(alarmvals[2] & 0x3f);
alrm->time.tm_mday = bcd2bin(alarmvals[1] & 0x3f);
- alrm->time.tm_mon = bcd2bin(alarmvals[0] & 0x3f);
+ alrm->time.tm_mon = bcd2bin(alarmvals[0] & 0x3f) - 1;
alrm->enabled = !!(alarmvals[0] & M41T80_ALMON_AFE);
alrm->pending = (flags & M41T80_FLAGS_AF) && alrm->enabled;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Marc Zyngier <[email protected]>
commit 107352a24900fb458152b92a4e72fbdc83fd5510 upstream.
We currently only halt the guest when a vCPU messes with the active
state of an SPI. This is perfectly fine for GICv2, but isn't enough
for GICv3, where all vCPUs can access the state of any other vCPU.
Let's broaden the condition to include any GICv3 interrupt that
has an active state (i.e. all but LPIs).
Cc: [email protected]
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
virt/kvm/arm/vgic/vgic-mmio.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
--- a/virt/kvm/arm/vgic/vgic-mmio.c
+++ b/virt/kvm/arm/vgic/vgic-mmio.c
@@ -368,14 +368,16 @@ static void vgic_mmio_change_active(stru
*/
static void vgic_change_active_prepare(struct kvm_vcpu *vcpu, u32 intid)
{
- if (intid > VGIC_NR_PRIVATE_IRQS)
+ if (vcpu->kvm->arch.vgic.vgic_model == KVM_DEV_TYPE_ARM_VGIC_V3 ||
+ intid > VGIC_NR_PRIVATE_IRQS)
kvm_arm_halt_guest(vcpu->kvm);
}
/* See vgic_change_active_prepare */
static void vgic_change_active_finish(struct kvm_vcpu *vcpu, u32 intid)
{
- if (intid > VGIC_NR_PRIVATE_IRQS)
+ if (vcpu->kvm->arch.vgic.vgic_model == KVM_DEV_TYPE_ARM_VGIC_V3 ||
+ intid > VGIC_NR_PRIVATE_IRQS)
kvm_arm_resume_guest(vcpu->kvm);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sean Young <[email protected]>
commit e5bb9d3d755f128956ed467ae50b41d22bb680c6 upstream.
This fixes an oops in ir_lirc_scancode_event().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000038
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 9 PID: 27687 Comm: kworker/9:2 Tainted: P OE 4.18.12-200.fc28.x86_64 #1
Hardware name: Supermicro C7X99-OCE-F/C7X99-OCE-F, BIOS 2.1a 06/15/2018
Workqueue: events pulse8_irq_work_handler [pulse8_cec]
RIP: 0010:ir_lirc_scancode_event+0x3d/0xb0 [rc_core]
Code: 8d ae b4 07 00 00 49 81 c6 b8 07 00 00 53 e8 4a df c3 d5 48 89 ef 49 89 45 00 e8 4e 84 41 d6 49 8b 1e 49 89 c4 4c 39 f3 74 58 <8b> 43 38 8b 53 40 89 c1 2b 4b 3c 39 ca 72 41 21 d0 49 8b 7d 00 49
RSP: 0018:ffffaa10e3c07d58 EFLAGS: 00010017
RAX: 0000000000000002 RBX: 0000000000000000 RCX: 0000000000000018
RDX: 0000000000000001 RSI: 00316245397fa93c RDI: ffff966d31c8d7b4
RBP: ffff966d31c8d7b4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000003 R11: ffffaa10e3c07e28 R12: 0000000000000002
R13: ffffaa10e3c07d88 R14: ffff966d31c8d7b8 R15: 0000000000000073
FS: 0000000000000000(0000) GS:ffff966d3f440000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000038 CR3: 00000009d820a003 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
ir_do_keydown+0x75/0x260 [rc_core]
rc_keydown+0x54/0xc0 [rc_core]
cec_received_msg_ts+0xaa8/0xaf0 [cec]
process_one_work+0x1a1/0x350
worker_thread+0x30/0x380
? pwq_unbound_release_workfn+0xd0/0xd0
kthread+0x112/0x130
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x35/0x40
Modules linked in: rc_tt_1500 dvb_usb_dvbsky dvb_usb_v2 uas usb_storage fuse vhost_net vhost tap xt_CHECKSUM iptable_mangle ip6t_REJECT nf_reject_ipv6 tun 8021q garp mrp xt_nat macvlan xfs devlink ebta
si2157 si2168 cx25840 cx23885 kvm altera_ci tda18271 joydev ir_rc6_decoder rc_rc6_mce crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_cstate intel_uncore altera_stapl m88ds3103 tveeprom cx2341
mxm_wmi igb crc32c_intel megaraid_sas dca i2c_algo_bit wmi vfio_pci irqbypass vfio_virqfd vfio_iommu_type1 vfio i2c_dev
CR2: 0000000000000038
Cc: <[email protected]> # v4.16+
Signed-off-by: Sean Young <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/rc/rc-main.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
--- a/drivers/media/rc/rc-main.c
+++ b/drivers/media/rc/rc-main.c
@@ -707,7 +707,8 @@ void rc_repeat(struct rc_dev *dev)
(dev->last_toggle ? LIRC_SCANCODE_FLAG_TOGGLE : 0)
};
- ir_lirc_scancode_event(dev, &sc);
+ if (dev->allowed_protocols != RC_PROTO_BIT_CEC)
+ ir_lirc_scancode_event(dev, &sc);
spin_lock_irqsave(&dev->keylock, flags);
@@ -747,7 +748,8 @@ static void ir_do_keydown(struct rc_dev
.keycode = keycode
};
- ir_lirc_scancode_event(dev, &sc);
+ if (dev->allowed_protocols != RC_PROTO_BIT_CEC)
+ ir_lirc_scancode_event(dev, &sc);
if (new_event && dev->keypressed)
ir_do_keyup(dev, false);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Luca Ceresoli <[email protected]>
commit cea8c0077d6cf3a0cea2f18a8e914af78d46b2ff upstream.
imx274_read_reg() takes a u8 pointer ("reg") and casts it to pass it
to regmap_read(), which takes an unsigned int pointer. This results in
a corrupted stack and random crashes.
Fixes: 0985dd306f72 ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Cc: [email protected] # for 4.15 and up
Signed-off-by: Luca Ceresoli <[email protected]>
Signed-off-by: Sakari Ailus <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/i2c/imx274.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
--- a/drivers/media/i2c/imx274.c
+++ b/drivers/media/i2c/imx274.c
@@ -636,16 +636,19 @@ static int imx274_write_table(struct sti
static inline int imx274_read_reg(struct stimx274 *priv, u16 addr, u8 *val)
{
+ unsigned int uint_val;
int err;
- err = regmap_read(priv->regmap, addr, (unsigned int *)val);
+ err = regmap_read(priv->regmap, addr, &uint_val);
if (err)
dev_err(&priv->client->dev,
"%s : i2c read failed, addr = %x\n", __func__, addr);
else
dev_dbg(&priv->client->dev,
"%s : addr 0x%x, val=0x%x\n", __func__,
- addr, *val);
+ addr, uint_val);
+
+ *val = uint_val;
return err;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans Verkuil <[email protected]>
commit 560ccb75c2caa6b1039dec1a53cd2ef526f5bf03 upstream.
When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.
Signed-off-by: Hans Verkuil <[email protected]>
Reported-by: [email protected]
Cc: <[email protected]> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/platform/vivid/vivid-vid-cap.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/media/platform/vivid/vivid-vid-cap.c
+++ b/drivers/media/platform/vivid/vivid-vid-cap.c
@@ -438,6 +438,8 @@ void vivid_update_format_cap(struct vivi
tpg_s_rgb_range(&dev->tpg, v4l2_ctrl_g_ctrl(dev->rgb_range_cap));
break;
}
+ vfree(dev->bitmap_cap);
+ dev->bitmap_cap = NULL;
vivid_update_quality(dev);
tpg_reset_source(&dev->tpg, dev->src_rect.width, dev->src_rect.height, dev->field_cap);
dev->crop_cap = dev->src_rect;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jaegeuk Kim <[email protected]>
commit 64beba0558fce7b59e9a8a7afd77290e82a22163 upstream.
There is a security report where f2fs_getxattr() has a hole to expose wrong
memory region when the image is malformed like this.
f2fs_getxattr: entry->e_name_len: 4, size: 12288, buffer_size: 16384, len: 4
Cc: <[email protected]>
Signed-off-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/f2fs/xattr.c | 18 +++++++++++++-----
1 file changed, 13 insertions(+), 5 deletions(-)
--- a/fs/f2fs/xattr.c
+++ b/fs/f2fs/xattr.c
@@ -291,7 +291,7 @@ static int read_xattr_block(struct inode
static int lookup_all_xattrs(struct inode *inode, struct page *ipage,
unsigned int index, unsigned int len,
const char *name, struct f2fs_xattr_entry **xe,
- void **base_addr)
+ void **base_addr, int *base_size)
{
void *cur_addr, *txattr_addr, *last_addr = NULL;
nid_t xnid = F2FS_I(inode)->i_xattr_nid;
@@ -302,8 +302,8 @@ static int lookup_all_xattrs(struct inod
if (!size && !inline_size)
return -ENODATA;
- txattr_addr = f2fs_kzalloc(F2FS_I_SB(inode),
- inline_size + size + XATTR_PADDING_SIZE, GFP_NOFS);
+ *base_size = inline_size + size + XATTR_PADDING_SIZE;
+ txattr_addr = f2fs_kzalloc(F2FS_I_SB(inode), *base_size, GFP_NOFS);
if (!txattr_addr)
return -ENOMEM;
@@ -315,8 +315,10 @@ static int lookup_all_xattrs(struct inod
*xe = __find_inline_xattr(inode, txattr_addr, &last_addr,
index, len, name);
- if (*xe)
+ if (*xe) {
+ *base_size = inline_size;
goto check;
+ }
}
/* read from xattr node block */
@@ -477,6 +479,7 @@ int f2fs_getxattr(struct inode *inode, i
int error = 0;
unsigned int size, len;
void *base_addr = NULL;
+ int base_size;
if (name == NULL)
return -EINVAL;
@@ -487,7 +490,7 @@ int f2fs_getxattr(struct inode *inode, i
down_read(&F2FS_I(inode)->i_xattr_sem);
error = lookup_all_xattrs(inode, ipage, index, len, name,
- &entry, &base_addr);
+ &entry, &base_addr, &base_size);
up_read(&F2FS_I(inode)->i_xattr_sem);
if (error)
return error;
@@ -501,6 +504,11 @@ int f2fs_getxattr(struct inode *inode, i
if (buffer) {
char *pval = entry->e_name + entry->e_name_len;
+
+ if (base_size - (pval - (char *)base_addr) < size) {
+ error = -ERANGE;
+ goto out;
+ }
memcpy(buffer, pval, size);
}
error = size;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Will Deacon <[email protected]>
commit 169113ece0f29ebe884a6cfcf57c1ace04d8a36a upstream.
The ARM Linux kernel handles the EABI syscall numbers as follows:
0 - NR_SYSCALLS-1 : Invoke syscall via syscall table
NR_SYSCALLS - 0xeffff : -ENOSYS (to be allocated in future)
0xf0000 - 0xf07ff : Private syscall or -ENOSYS if not allocated
> 0xf07ff : SIGILL
Our compat code gets this wrong and ends up sending SIGILL in response
to all syscalls greater than NR_SYSCALLS which have a value greater
than 0x7ff in the bottom 16 bits.
Fix this by defining the end of the ARM private syscall region and
checking the syscall number against that directly. Update the comment
while we're at it.
Cc: <[email protected]>
Cc: Dave Martin <[email protected]>
Reported-by: Pi-Hsun Shih <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm64/include/asm/unistd.h | 5 +++--
arch/arm64/kernel/sys_compat.c | 4 ++--
2 files changed, 5 insertions(+), 4 deletions(-)
--- a/arch/arm64/include/asm/unistd.h
+++ b/arch/arm64/include/asm/unistd.h
@@ -40,8 +40,9 @@
* The following SVCs are ARM private.
*/
#define __ARM_NR_COMPAT_BASE 0x0f0000
-#define __ARM_NR_compat_cacheflush (__ARM_NR_COMPAT_BASE+2)
-#define __ARM_NR_compat_set_tls (__ARM_NR_COMPAT_BASE+5)
+#define __ARM_NR_compat_cacheflush (__ARM_NR_COMPAT_BASE + 2)
+#define __ARM_NR_compat_set_tls (__ARM_NR_COMPAT_BASE + 5)
+#define __ARM_NR_COMPAT_END (__ARM_NR_COMPAT_BASE + 0x800)
#define __NR_compat_syscalls 399
#endif
--- a/arch/arm64/kernel/sys_compat.c
+++ b/arch/arm64/kernel/sys_compat.c
@@ -102,12 +102,12 @@ long compat_arm_syscall(struct pt_regs *
default:
/*
- * Calls 9f00xx..9f07ff are defined to return -ENOSYS
+ * Calls 0xf0xxx..0xf07ff are defined to return -ENOSYS
* if not implemented, rather than raising SIGILL. This
* way the calling program can gracefully determine whether
* a feature is supported.
*/
- if ((no & 0xffff) <= 0x7ff)
+ if (no < __ARM_NR_COMPAT_END)
return -ENOSYS;
break;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Robin Murphy <[email protected]>
commit 3cd508a8c1379427afb5e16c2e0a7c986d907853 upstream.
When we insert the sync sequence number into the CMD_SYNC.MSIData field,
we do so in CPU-native byte order, before writing out the whole command
as explicitly little-endian dwords. Thus on big-endian systems, the SMMU
will receive and write back a byteswapped version of sync_nr, which would
be perfect if it were targeting a similarly-little-endian ITS, but since
it's actually writing back to memory being polled by the CPUs, they're
going to end up seeing the wrong thing.
Since the SMMU doesn't care what the MSIData actually contains, the
minimal-overhead solution is to simply add an extra byteswap initially,
such that it then writes back the big-endian format directly.
Cc: <[email protected]>
Fixes: 37de98f8f1cf ("iommu/arm-smmu-v3: Use CMD_SYNC completion MSI")
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/iommu/arm-smmu-v3.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
--- a/drivers/iommu/arm-smmu-v3.c
+++ b/drivers/iommu/arm-smmu-v3.c
@@ -837,7 +837,13 @@ static int arm_smmu_cmdq_build_cmd(u64 *
cmd[0] |= FIELD_PREP(CMDQ_SYNC_0_CS, CMDQ_SYNC_0_CS_SEV);
cmd[0] |= FIELD_PREP(CMDQ_SYNC_0_MSH, ARM_SMMU_SH_ISH);
cmd[0] |= FIELD_PREP(CMDQ_SYNC_0_MSIATTR, ARM_SMMU_MEMATTR_OIWB);
- cmd[0] |= FIELD_PREP(CMDQ_SYNC_0_MSIDATA, ent->sync.msidata);
+ /*
+ * Commands are written little-endian, but we want the SMMU to
+ * receive MSIData, and thus write it back to memory, in CPU
+ * byte order, so big-endian needs an extra byteswap here.
+ */
+ cmd[0] |= FIELD_PREP(CMDQ_SYNC_0_MSIDATA,
+ cpu_to_le32(ent->sync.msidata));
cmd[1] |= ent->sync.msiaddr & CMDQ_SYNC_1_MSIADDR_MASK;
break;
default:
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Steven Rostedt (VMware) <[email protected]>
commit f024cf085c423bac7512479f45c34ee9a24af7ce upstream.
In the case that a bprintk event has a dereferenced pointer that is
stored as a string, and there's more values to process (more args), the
arg was not updated to point to the next arg after processing the
dereferenced pointer, and it screwed up what was to be displayed.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: [email protected]
Cc: [email protected]
Fixes: 37db96bb49629 ("tools lib traceevent: Handle new pointer processing of bprint strings")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/lib/traceevent/event-parse.c | 1 +
1 file changed, 1 insertion(+)
--- a/tools/lib/traceevent/event-parse.c
+++ b/tools/lib/traceevent/event-parse.c
@@ -4968,6 +4968,7 @@ static void pretty_print(struct trace_se
if (arg->type == PRINT_BSTRING) {
trace_seq_puts(s, arg->string.string);
+ arg = arg->next;
break;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Aaro Koskinen <[email protected]>
commit edefae94b7b9f10d5efe32dece5a36e9d9ecc29e upstream.
Commit 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx
interface detection") added RGMII interface detection for OCTEON III,
but it results in the following logs:
[ 7.165984] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
[ 7.173017] ERROR: Unsupported Octeon model in __cvmx_helper_rgmii_probe
The current RGMII routines are valid only for older OCTEONS that
use GMX/ASX hardware blocks. On later chips AGL should be used,
but support for that is missing in the mainline. Until that is added,
mark the interface as disabled.
Fixes: 885872b722b7 ("MIPS: Octeon: Add Octeon III CN7xxx interface detection")
Signed-off-by: Aaro Koskinen <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: James Hogan <[email protected]>
Cc: [email protected]
Cc: [email protected] # 4.7+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/cavium-octeon/executive/cvmx-helper.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/arch/mips/cavium-octeon/executive/cvmx-helper.c
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper.c
@@ -286,7 +286,8 @@ static cvmx_helper_interface_mode_t __cv
case 3:
return CVMX_HELPER_INTERFACE_MODE_LOOP;
case 4:
- return CVMX_HELPER_INTERFACE_MODE_RGMII;
+ /* TODO: Implement support for AGL (RGMII). */
+ return CVMX_HELPER_INTERFACE_MODE_DISABLED;
default:
return CVMX_HELPER_INTERFACE_MODE_DISABLED;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huacai Chen <[email protected]>
commit db1ce3f5d01d2d6d5714aefba0159d2cb5167a0b upstream.
Commit 4936084c2ee2 ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
introduce a mistake in atomic64_fetch_##op##_relaxed(), because it
forget to delete R10000_LLSC_WAR in the if-condition. So fix it.
Fixes: 4936084c2ee2 ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
Signed-off-by: Huacai Chen <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Cc: Joshua Kinard <[email protected]>
Cc: Ralf Baechle <[email protected]>
Cc: Steven J . Hill <[email protected]>
Cc: Fuxin Zhang <[email protected]>
Cc: Zhangjin Wu <[email protected]>
Cc: [email protected]
Cc: [email protected] # 4.19+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/include/asm/atomic.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/mips/include/asm/atomic.h
+++ b/arch/mips/include/asm/atomic.h
@@ -306,7 +306,7 @@ static __inline__ long atomic64_fetch_##
{ \
long result; \
\
- if (kernel_uses_llsc && R10000_LLSC_WAR) { \
+ if (kernel_uses_llsc) { \
long temp; \
\
__asm__ __volatile__( \
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huacai Chen <[email protected]>
commit 92aa0718c9fa5160ad2f0e7b5bffb52f1ea1e51a upstream.
This patch is borrowed from ARM64 to ensure pmd_present() returns false
after pmd_mknotpresent(). This is needed for THP.
References: 5bb1cc0ff9a6 ("arm64: Ensure pmd_present() returns false after pmd_mknotpresent()")
Reviewed-by: James Hogan <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/21135/
Cc: Ralf Baechle <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Steven J . Hill <[email protected]>
Cc: [email protected]
Cc: Fuxin Zhang <[email protected]>
Cc: Zhangjin Wu <[email protected]>
Cc: <[email protected]> # 3.8+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/include/asm/pgtable-64.h | 5 +++++
1 file changed, 5 insertions(+)
--- a/arch/mips/include/asm/pgtable-64.h
+++ b/arch/mips/include/asm/pgtable-64.h
@@ -265,6 +265,11 @@ static inline int pmd_bad(pmd_t pmd)
static inline int pmd_present(pmd_t pmd)
{
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+ if (unlikely(pmd_val(pmd) & _PAGE_HUGE))
+ return pmd_val(pmd) & _PAGE_PRESENT;
+#endif
+
return pmd_val(pmd) != (unsigned long) invalid_pte_table;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Adrian Hunter <[email protected]>
commit 8e80ad9983caeee09c3a0a1a37e05bff93becce4 upstream.
For branch stacks or branch samples, the sample cpumode might not be
correct because it applies only to the sample 'ip' and not necessary to
'addr' or branch stack addresses. Add fallback functions that can be
used to deal with those cases
Signed-off-by: Adrian Hunter <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Leo Yan <[email protected]>
Cc: Mathieu Poirier <[email protected]>
Cc: [email protected] # 4.19
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
tools/perf/util/event.c | 27 +++++++++++++++++++++++++++
tools/perf/util/machine.c | 27 +++++++++++++++++++++++++++
tools/perf/util/machine.h | 2 ++
tools/perf/util/thread.h | 4 ++++
4 files changed, 60 insertions(+)
--- a/tools/perf/util/event.c
+++ b/tools/perf/util/event.c
@@ -1576,6 +1576,24 @@ struct map *thread__find_map(struct thre
return al->map;
}
+/*
+ * For branch stacks or branch samples, the sample cpumode might not be correct
+ * because it applies only to the sample 'ip' and not necessary to 'addr' or
+ * branch stack addresses. If possible, use a fallback to deal with those cases.
+ */
+struct map *thread__find_map_fb(struct thread *thread, u8 cpumode, u64 addr,
+ struct addr_location *al)
+{
+ struct map *map = thread__find_map(thread, cpumode, addr, al);
+ struct machine *machine = thread->mg->machine;
+ u8 addr_cpumode = machine__addr_cpumode(machine, cpumode, addr);
+
+ if (map || addr_cpumode == cpumode)
+ return map;
+
+ return thread__find_map(thread, addr_cpumode, addr, al);
+}
+
struct symbol *thread__find_symbol(struct thread *thread, u8 cpumode,
u64 addr, struct addr_location *al)
{
@@ -1584,6 +1602,15 @@ struct symbol *thread__find_symbol(struc
al->sym = map__find_symbol(al->map, al->addr);
return al->sym;
}
+
+struct symbol *thread__find_symbol_fb(struct thread *thread, u8 cpumode,
+ u64 addr, struct addr_location *al)
+{
+ al->sym = NULL;
+ if (thread__find_map_fb(thread, cpumode, addr, al))
+ al->sym = map__find_symbol(al->map, al->addr);
+ return al->sym;
+}
/*
* Callers need to drop the reference to al->thread, obtained in
--- a/tools/perf/util/machine.c
+++ b/tools/perf/util/machine.c
@@ -2575,6 +2575,33 @@ int machine__get_kernel_start(struct mac
return err;
}
+u8 machine__addr_cpumode(struct machine *machine, u8 cpumode, u64 addr)
+{
+ u8 addr_cpumode = cpumode;
+ bool kernel_ip;
+
+ if (!machine->single_address_space)
+ goto out;
+
+ kernel_ip = machine__kernel_ip(machine, addr);
+ switch (cpumode) {
+ case PERF_RECORD_MISC_KERNEL:
+ case PERF_RECORD_MISC_USER:
+ addr_cpumode = kernel_ip ? PERF_RECORD_MISC_KERNEL :
+ PERF_RECORD_MISC_USER;
+ break;
+ case PERF_RECORD_MISC_GUEST_KERNEL:
+ case PERF_RECORD_MISC_GUEST_USER:
+ addr_cpumode = kernel_ip ? PERF_RECORD_MISC_GUEST_KERNEL :
+ PERF_RECORD_MISC_GUEST_USER;
+ break;
+ default:
+ break;
+ }
+out:
+ return addr_cpumode;
+}
+
struct dso *machine__findnew_dso(struct machine *machine, const char *filename)
{
return dsos__findnew(&machine->dsos, filename);
--- a/tools/perf/util/machine.h
+++ b/tools/perf/util/machine.h
@@ -100,6 +100,8 @@ static inline bool machine__kernel_ip(st
return ip >= kernel_start;
}
+u8 machine__addr_cpumode(struct machine *machine, u8 cpumode, u64 addr);
+
struct thread *machine__find_thread(struct machine *machine, pid_t pid,
pid_t tid);
struct comm *machine__thread_exec_comm(struct machine *machine,
--- a/tools/perf/util/thread.h
+++ b/tools/perf/util/thread.h
@@ -94,9 +94,13 @@ struct thread *thread__main_thread(struc
struct map *thread__find_map(struct thread *thread, u8 cpumode, u64 addr,
struct addr_location *al);
+struct map *thread__find_map_fb(struct thread *thread, u8 cpumode, u64 addr,
+ struct addr_location *al);
struct symbol *thread__find_symbol(struct thread *thread, u8 cpumode,
u64 addr, struct addr_location *al);
+struct symbol *thread__find_symbol_fb(struct thread *thread, u8 cpumode,
+ u64 addr, struct addr_location *al);
void thread__find_cpumode_addr_location(struct thread *thread, u64 addr,
struct addr_location *al);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lukas Wunner <[email protected]>
commit 56c1723426d3cfd4723bfbfce531d7b38bae6266 upstream.
The IRQ handler bcm2835_spi_interrupt() first reads as much as possible
from the RX FIFO, then writes as much as possible to the TX FIFO.
Afterwards it decides whether the transfer is finished by checking if
the TX FIFO is empty.
If very few bytes were written to the TX FIFO, they may already have
been transmitted by the time the FIFO's emptiness is checked. As a
result, the transfer will be declared finished and the chip will be
reset without reading the corresponding received bytes from the RX FIFO.
The odds of this happening increase with a high clock frequency (such
that the TX FIFO drains quickly) and either passing "threadirqs" on the
command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ
handler may be preempted between filling the TX FIFO and checking its
emptiness).
Fix by instead checking whether rx_len has reached zero, which means
that the transfer has been received in full. This is also more
efficient as it avoids one bus read access per interrupt. Note that
bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine
whether the transfer has finished.
Signed-off-by: Lukas Wunner <[email protected]>
Fixes: e34ff011c70e ("spi: bcm2835: move to the transfer_one driver model")
Cc: [email protected] # v4.1+
Cc: Mathias Duckeck <[email protected]>
Cc: Frank Pavlic <[email protected]>
Cc: Martin Sperl <[email protected]>
Cc: Noralf Trønnes <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-bcm2835.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -155,8 +155,7 @@ static irqreturn_t bcm2835_spi_interrupt
/* Write as many bytes as possible to FIFO */
bcm2835_wr_fifo(bs);
- /* based on flags decide if we can finish the transfer */
- if (bcm2835_rd(bs, BCM2835_SPI_CS) & BCM2835_SPI_CS_DONE) {
+ if (!bs->rx_len) {
/* Transfer complete - reset SPI HW */
bcm2835_spi_reset_hw(master);
/* wake up the framework */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Paul Burton <[email protected]>
commit adcc81f148d733b7e8e641300c5590a2cdc13bf3 upstream.
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: [email protected] # v4.8+
Cc: [email protected]
Cc: [email protected]
Cc: Rich Felker <[email protected]>
Cc: David Daney <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/kernel/vdso.c | 4 ++--
arch/mips/math-emu/dsemul.c | 38 ++++++++++++++++++++------------------
2 files changed, 22 insertions(+), 20 deletions(-)
--- a/arch/mips/kernel/vdso.c
+++ b/arch/mips/kernel/vdso.c
@@ -126,8 +126,8 @@ int arch_setup_additional_pages(struct l
/* Map delay slot emulation page */
base = mmap_region(NULL, STACK_TOP, PAGE_SIZE,
- VM_READ|VM_WRITE|VM_EXEC|
- VM_MAYREAD|VM_MAYWRITE|VM_MAYEXEC,
+ VM_READ | VM_EXEC |
+ VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC,
0, NULL);
if (IS_ERR_VALUE(base)) {
ret = base;
--- a/arch/mips/math-emu/dsemul.c
+++ b/arch/mips/math-emu/dsemul.c
@@ -214,8 +214,9 @@ int mips_dsemul(struct pt_regs *regs, mi
{
int isa16 = get_isa16_mode(regs->cp0_epc);
mips_instruction break_math;
- struct emuframe __user *fr;
- int err, fr_idx;
+ unsigned long fr_uaddr;
+ struct emuframe fr;
+ int fr_idx, ret;
/* NOP is easy */
if (ir == 0)
@@ -250,27 +251,31 @@ int mips_dsemul(struct pt_regs *regs, mi
fr_idx = alloc_emuframe();
if (fr_idx == BD_EMUFRAME_NONE)
return SIGBUS;
- fr = &dsemul_page()[fr_idx];
/* Retrieve the appropriately encoded break instruction */
break_math = BREAK_MATH(isa16);
/* Write the instructions to the frame */
if (isa16) {
- err = __put_user(ir >> 16,
- (u16 __user *)(&fr->emul));
- err |= __put_user(ir & 0xffff,
- (u16 __user *)((long)(&fr->emul) + 2));
- err |= __put_user(break_math >> 16,
- (u16 __user *)(&fr->badinst));
- err |= __put_user(break_math & 0xffff,
- (u16 __user *)((long)(&fr->badinst) + 2));
+ union mips_instruction _emul = {
+ .halfword = { ir >> 16, ir }
+ };
+ union mips_instruction _badinst = {
+ .halfword = { break_math >> 16, break_math }
+ };
+
+ fr.emul = _emul.word;
+ fr.badinst = _badinst.word;
} else {
- err = __put_user(ir, &fr->emul);
- err |= __put_user(break_math, &fr->badinst);
+ fr.emul = ir;
+ fr.badinst = break_math;
}
- if (unlikely(err)) {
+ /* Write the frame to user memory */
+ fr_uaddr = (unsigned long)&dsemul_page()[fr_idx];
+ ret = access_process_vm(current, fr_uaddr, &fr, sizeof(fr),
+ FOLL_FORCE | FOLL_WRITE);
+ if (unlikely(ret != sizeof(fr))) {
MIPS_FPU_EMU_INC_STATS(errors);
free_emuframe(fr_idx, current->mm);
return SIGBUS;
@@ -282,10 +287,7 @@ int mips_dsemul(struct pt_regs *regs, mi
atomic_set(¤t->thread.bd_emu_frame, fr_idx);
/* Change user register context to execute the frame */
- regs->cp0_epc = (unsigned long)&fr->emul | isa16;
-
- /* Ensure the icache observes our newly written frame */
- flush_cache_sigtramp((unsigned long)&fr->emul);
+ regs->cp0_epc = fr_uaddr | isa16;
return 0;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit acb4a33e9856d5fa3384b87d3d8369229be06d31 ]
tipc_udp_xmit() drops the packet on error, there is no
need to drop it again.
Fixes: ef20cd4dd163 ("tipc: introduce UDP replicast")
Reported-and-tested-by: [email protected]
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/udp_media.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
--- a/net/tipc/udp_media.c
+++ b/net/tipc/udp_media.c
@@ -245,10 +245,8 @@ static int tipc_udp_send_msg(struct net
}
err = tipc_udp_xmit(net, _skb, ub, src, &rcast->addr);
- if (err) {
- kfree_skb(_skb);
+ if (err)
goto out;
- }
}
err = 0;
out:
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit fb83ed496b9a654f60cd1d58a0e1e79ec5694808 ]
When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.
We should just error out when the remote address and local address
have different protocols.
Reported-by: [email protected]
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/udp_media.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/net/tipc/udp_media.c
+++ b/net/tipc/udp_media.c
@@ -680,6 +680,11 @@ static int tipc_udp_enable(struct net *n
if (err)
goto err;
+ if (remote.proto != local.proto) {
+ err = -EINVAL;
+ goto err;
+ }
+
/* Autoconfigure own node identity if needed */
if (!tipc_own_id(net)) {
memcpy(node_id, local.ipv6.in6_u.u6_addr8, 16);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jernej Skrabec <[email protected]>
commit 65b6657672388b72822e0367f06d41c1e3ffb5bb upstream.
Allwinner H6 SoC has multiplier N range between 1 and 254. Since parent
rate is 24MHz, intermediate result when calculating final rate easily
overflows 32 bit variable.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Fixes: 6174a1e24b0d ("clk: sunxi-ng: Add N-M-factor clock support")
Fixes: ee28648cb2b4 ("clk: sunxi-ng: Remove the use of rational computations")
CC: <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/clk/sunxi-ng/ccu_nm.c | 18 +++++++++++++++---
1 file changed, 15 insertions(+), 3 deletions(-)
--- a/drivers/clk/sunxi-ng/ccu_nm.c
+++ b/drivers/clk/sunxi-ng/ccu_nm.c
@@ -19,6 +19,17 @@ struct _ccu_nm {
unsigned long m, min_m, max_m;
};
+static unsigned long ccu_nm_calc_rate(unsigned long parent,
+ unsigned long n, unsigned long m)
+{
+ u64 rate = parent;
+
+ rate *= n;
+ do_div(rate, m);
+
+ return rate;
+}
+
static void ccu_nm_find_best(unsigned long parent, unsigned long rate,
struct _ccu_nm *nm)
{
@@ -28,7 +39,8 @@ static void ccu_nm_find_best(unsigned lo
for (_n = nm->min_n; _n <= nm->max_n; _n++) {
for (_m = nm->min_m; _m <= nm->max_m; _m++) {
- unsigned long tmp_rate = parent * _n / _m;
+ unsigned long tmp_rate = ccu_nm_calc_rate(parent,
+ _n, _m);
if (tmp_rate > rate)
continue;
@@ -100,7 +112,7 @@ static unsigned long ccu_nm_recalc_rate(
if (ccu_sdm_helper_is_enabled(&nm->common, &nm->sdm))
rate = ccu_sdm_helper_read_rate(&nm->common, &nm->sdm, m, n);
else
- rate = parent_rate * n / m;
+ rate = ccu_nm_calc_rate(parent_rate, n, m);
if (nm->common.features & CCU_FEATURE_FIXED_POSTDIV)
rate /= nm->fixed_post_div;
@@ -142,7 +154,7 @@ static long ccu_nm_round_rate(struct clk
_nm.max_m = nm->m.max ?: 1 << nm->m.width;
ccu_nm_find_best(*parent_rate, rate, &_nm);
- rate = *parent_rate * _nm.n / _nm.m;
+ rate = ccu_nm_calc_rate(*parent_rate, _nm.n, _nm.m);
if (nm->common.features & CCU_FEATURE_FIXED_POSTDIV)
rate /= nm->fixed_post_div;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit d5c7c745f254c6cb98b3b3f15fe789b8bd770c72 ]
When x25_asy_open() fails, it already cleans up by itself,
so its caller doesn't need to free the memory again.
It seems we still have to call x25_asy_free() to clear the SLF_INUSE
bit, so just set these pointers to NULL after kfree().
Reported-and-tested-by: [email protected]
Fixes: 3b780bed3138 ("x25_asy: Free x25_asy on x25_asy_open() failure.")
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/wan/x25_asy.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/net/wan/x25_asy.c
+++ b/drivers/net/wan/x25_asy.c
@@ -486,8 +486,10 @@ static int x25_asy_open(struct net_devic
/* Cleanup */
kfree(sl->xbuff);
+ sl->xbuff = NULL;
noxbuff:
kfree(sl->rbuff);
+ sl->rbuff = NULL;
norbuff:
return -ENOMEM;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Claudiu Beznea <[email protected]>
[ Upstream commit 4298388574dae6168fa8940b3edc7ba965e8a7ab ]
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/cadence/macb_main.c | 21 ++++++++++++++++++++-
1 file changed, 20 insertions(+), 1 deletion(-)
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -61,7 +61,8 @@
#define MACB_TX_ERR_FLAGS (MACB_BIT(ISR_TUND) \
| MACB_BIT(ISR_RLE) \
| MACB_BIT(TXERR))
-#define MACB_TX_INT_FLAGS (MACB_TX_ERR_FLAGS | MACB_BIT(TCOMP))
+#define MACB_TX_INT_FLAGS (MACB_TX_ERR_FLAGS | MACB_BIT(TCOMP) \
+ | MACB_BIT(TXUBR))
/* Max length of transmit frame must be a multiple of 8 bytes */
#define MACB_TX_LEN_ALIGN 8
@@ -1313,6 +1314,21 @@ static void macb_hresp_error_task(unsign
netif_tx_start_all_queues(dev);
}
+static void macb_tx_restart(struct macb_queue *queue)
+{
+ unsigned int head = queue->tx_head;
+ unsigned int tail = queue->tx_tail;
+ struct macb *bp = queue->bp;
+
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ queue_writel(queue, ISR, MACB_BIT(TXUBR));
+
+ if (head == tail)
+ return;
+
+ macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TSTART));
+}
+
static irqreturn_t macb_interrupt(int irq, void *dev_id)
{
struct macb_queue *queue = dev_id;
@@ -1370,6 +1386,9 @@ static irqreturn_t macb_interrupt(int ir
if (status & MACB_BIT(TCOMP))
macb_tx_interrupt(queue);
+ if (status & MACB_BIT(TXUBR))
+ macb_tx_restart(queue);
+
/* Link change detection isn't possible with RMII, so we'll
* add that if/when we get our hands on a full-blown MII PHY.
*/
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit 143ece654f9f5b37bedea252a990be37e48ae3a5 ]
tipc_wait_for_cond() drops socket lock before going to sleep,
but tsk->group could be freed right after that release_sock().
So we have to re-check and reload tsk->group after it wakes up.
After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when
tsk->group is NULL, instead of continuing with the assumption of
a non-NULL tsk->group.
(It looks like 'dsts' should be re-checked and reloaded too, but
it is a different bug.)
Similar for tipc_send_group_unicast() and tipc_send_group_anycast().
Reported-by: [email protected]
Fixes: b7d42635517f ("tipc: introduce flow control for group broadcast messages")
Fixes: ee106d7f942d ("tipc: introduce group anycast messaging")
Fixes: 27bd9ec027f3 ("tipc: introduce group unicast messaging")
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Ying Xue <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/socket.c | 25 ++++++++++++++-----------
1 file changed, 14 insertions(+), 11 deletions(-)
--- a/net/tipc/socket.c
+++ b/net/tipc/socket.c
@@ -878,7 +878,6 @@ static int tipc_send_group_unicast(struc
DECLARE_SOCKADDR(struct sockaddr_tipc *, dest, m->msg_name);
int blks = tsk_blocks(GROUP_H_SIZE + dlen);
struct tipc_sock *tsk = tipc_sk(sk);
- struct tipc_group *grp = tsk->group;
struct net *net = sock_net(sk);
struct tipc_member *mb = NULL;
u32 node, port;
@@ -892,7 +891,9 @@ static int tipc_send_group_unicast(struc
/* Block or return if destination link or member is congested */
rc = tipc_wait_for_cond(sock, &timeout,
!tipc_dest_find(&tsk->cong_links, node, 0) &&
- !tipc_group_cong(grp, node, port, blks, &mb));
+ tsk->group &&
+ !tipc_group_cong(tsk->group, node, port, blks,
+ &mb));
if (unlikely(rc))
return rc;
@@ -922,7 +923,6 @@ static int tipc_send_group_anycast(struc
struct tipc_sock *tsk = tipc_sk(sk);
struct list_head *cong_links = &tsk->cong_links;
int blks = tsk_blocks(GROUP_H_SIZE + dlen);
- struct tipc_group *grp = tsk->group;
struct tipc_msg *hdr = &tsk->phdr;
struct tipc_member *first = NULL;
struct tipc_member *mbr = NULL;
@@ -939,9 +939,10 @@ static int tipc_send_group_anycast(struc
type = msg_nametype(hdr);
inst = dest->addr.name.name.instance;
scope = msg_lookup_scope(hdr);
- exclude = tipc_group_exclude(grp);
while (++lookups < 4) {
+ exclude = tipc_group_exclude(tsk->group);
+
first = NULL;
/* Look for a non-congested destination member, if any */
@@ -950,7 +951,8 @@ static int tipc_send_group_anycast(struc
&dstcnt, exclude, false))
return -EHOSTUNREACH;
tipc_dest_pop(&dsts, &node, &port);
- cong = tipc_group_cong(grp, node, port, blks, &mbr);
+ cong = tipc_group_cong(tsk->group, node, port, blks,
+ &mbr);
if (!cong)
break;
if (mbr == first)
@@ -969,7 +971,8 @@ static int tipc_send_group_anycast(struc
/* Block or return if destination link or member is congested */
rc = tipc_wait_for_cond(sock, &timeout,
!tipc_dest_find(cong_links, node, 0) &&
- !tipc_group_cong(grp, node, port,
+ tsk->group &&
+ !tipc_group_cong(tsk->group, node, port,
blks, &mbr));
if (unlikely(rc))
return rc;
@@ -1004,8 +1007,7 @@ static int tipc_send_group_bcast(struct
struct sock *sk = sock->sk;
struct net *net = sock_net(sk);
struct tipc_sock *tsk = tipc_sk(sk);
- struct tipc_group *grp = tsk->group;
- struct tipc_nlist *dsts = tipc_group_dests(grp);
+ struct tipc_nlist *dsts = tipc_group_dests(tsk->group);
struct tipc_mc_method *method = &tsk->mc_method;
bool ack = method->mandatory && method->rcast;
int blks = tsk_blocks(MCAST_H_SIZE + dlen);
@@ -1018,8 +1020,9 @@ static int tipc_send_group_bcast(struct
return -EHOSTUNREACH;
/* Block or return if any destination link or member is congested */
- rc = tipc_wait_for_cond(sock, &timeout, !tsk->cong_link_cnt &&
- !tipc_group_bc_cong(grp, blks));
+ rc = tipc_wait_for_cond(sock, &timeout,
+ !tsk->cong_link_cnt && tsk->group &&
+ !tipc_group_bc_cong(tsk->group, blks));
if (unlikely(rc))
return rc;
@@ -1034,7 +1037,7 @@ static int tipc_send_group_bcast(struct
msg_set_hdr_sz(hdr, GROUP_H_SIZE);
msg_set_destport(hdr, 0);
msg_set_destnode(hdr, 0);
- msg_set_grp_bc_seqno(hdr, tipc_group_bc_snd_nxt(grp));
+ msg_set_grp_bc_seqno(hdr, tipc_group_bc_snd_nxt(tsk->group));
/* Avoid getting stuck with repeated forced replicasts */
msg_set_grp_bc_ack_req(hdr, ack);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit fb24274546310872eeeaf3d1d53799d8414aa0f2 ]
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879dd ("udp: Add udp_sock_create for UDP tunnels to open listener socket")
Reported-by: [email protected]
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/ip6_udp_tunnel.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/net/ipv6/ip6_udp_tunnel.c
+++ b/net/ipv6/ip6_udp_tunnel.c
@@ -15,7 +15,7 @@
int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg,
struct socket **sockp)
{
- struct sockaddr_in6 udp6_addr;
+ struct sockaddr_in6 udp6_addr = {};
int err;
struct socket *sock = NULL;
@@ -42,6 +42,7 @@ int udp_sock_create6(struct net *net, st
goto error;
if (cfg->peer_udp_port) {
+ memset(&udp6_addr, 0, sizeof(udp6_addr));
udp6_addr.sin6_family = AF_INET6;
memcpy(&udp6_addr.sin6_addr, &cfg->peer_ip6,
sizeof(udp6_addr.sin6_addr));
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Mikhael Goikhman <[email protected]>
[ Upstream commit d13b224f431579fe2d712871d4265d7a22ca6c9c ]
Remove tx_udp_seg_rem counter from ethtool output, as it is no longer
being updated in the driver's data flow.
Fixes: 3f44899ef2ce ("net/mlx5e: Use PARTIAL_GSO for UDP segmentation")
Signed-off-by: Mikhael Goikhman <[email protected]>
Reviewed-by: Eran Ben Elisha <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c | 2 --
drivers/net/ethernet/mellanox/mlx5/core/en_stats.h | 2 --
2 files changed, 4 deletions(-)
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_stats.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_stats.c
@@ -73,7 +73,6 @@ static const struct counter_desc sw_stat
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_recover) },
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_cqes) },
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_queue_wake) },
- { MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_udp_seg_rem) },
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_cqe_err) },
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_xdp_xmit) },
{ MLX5E_DECLARE_STAT(struct mlx5e_sw_stats, tx_xdp_full) },
@@ -194,7 +193,6 @@ void mlx5e_grp_sw_update_stats(struct ml
s->tx_nop += sq_stats->nop;
s->tx_queue_stopped += sq_stats->stopped;
s->tx_queue_wake += sq_stats->wake;
- s->tx_udp_seg_rem += sq_stats->udp_seg_rem;
s->tx_queue_dropped += sq_stats->dropped;
s->tx_cqe_err += sq_stats->cqe_err;
s->tx_recover += sq_stats->recover;
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_stats.h
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_stats.h
@@ -86,7 +86,6 @@ struct mlx5e_sw_stats {
u64 tx_recover;
u64 tx_cqes;
u64 tx_queue_wake;
- u64 tx_udp_seg_rem;
u64 tx_cqe_err;
u64 tx_xdp_xmit;
u64 tx_xdp_full;
@@ -217,7 +216,6 @@ struct mlx5e_sq_stats {
u64 csum_partial_inner;
u64 added_vlan_packets;
u64 nop;
- u64 udp_seg_rem;
#ifdef CONFIG_MLX5_EN_TLS
u64 tls_ooo;
u64 tls_resync_bytes;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jason Wang <[email protected]>
[ Upstream commit 841df922417eb82c835e93d4b93eb6a68c99d599 ]
We miss a write barrier that guarantees used idx is updated and seen
before log. This will let userspace sync and copy used ring before
used idx is update. Fix this by adding a barrier before log_write().
Fixes: 8dd014adfea6f ("vhost-net: mergeable buffers support")
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: Jason Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/vhost/vhost.c | 2 ++
1 file changed, 2 insertions(+)
--- a/drivers/vhost/vhost.c
+++ b/drivers/vhost/vhost.c
@@ -2233,6 +2233,8 @@ int vhost_add_used_n(struct vhost_virtqu
return -EFAULT;
}
if (unlikely(vq->log_used)) {
+ /* Make sure used idx is seen before log. */
+ smp_wmb();
/* Log used index update. */
log_write(vq->log_base,
vq->log_addr + offsetof(struct vring_used, idx),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stefano Brivio <[email protected]>
[ Upstream commit 7adf3246092f5e87ed0fa610e8088fae416c581f ]
In ip6_neigh_lookup(), we must not return errors coming from
neigh_create(): if creation of a neighbour entry fails, the lookup should
return NULL, in the same way as it's done in __neigh_lookup().
Otherwise, callers legitimately checking for a non-NULL return value of
the lookup function might dereference an invalid pointer.
For instance, on neighbour table overflow, ndisc_router_discovery()
crashes ndisc_update() by passing ERR_PTR(-ENOBUFS) as 'neigh' argument.
Reported-by: Jianlin Shi <[email protected]>
Fixes: f8a1b43b709d ("net/ipv6: Create a neigh_lookup for FIB entries")
Signed-off-by: Stefano Brivio <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv6/route.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/net/ipv6/route.c
+++ b/net/ipv6/route.c
@@ -210,7 +210,9 @@ struct neighbour *ip6_neigh_lookup(const
n = __ipv6_neigh_lookup(dev, daddr);
if (n)
return n;
- return neigh_create(&nd_tbl, daddr, dev);
+
+ n = neigh_create(&nd_tbl, daddr, dev);
+ return IS_ERR(n) ? NULL : n;
}
static struct neighbour *ip6_dst_neigh_lookup(const struct dst_entry *dst,
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jörgen Storvist <[email protected]>
[ Upstream commit 110a1cc28bc383adb4885eff27e18c61ddebffb4 ]
Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/usb/qmi_wwan.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1117,6 +1117,7 @@ static const struct usb_device_id produc
{QMI_FIXED_INTF(0x1435, 0xd181, 4)}, /* Wistron NeWeb D18Q1 */
{QMI_FIXED_INTF(0x1435, 0xd181, 5)}, /* Wistron NeWeb D18Q1 */
{QMI_FIXED_INTF(0x1435, 0xd191, 4)}, /* Wistron NeWeb D19Q1 */
+ {QMI_QUIRK_SET_DTR(0x1508, 0x1001, 4)}, /* Fibocom NL668 series */
{QMI_FIXED_INTF(0x16d8, 0x6003, 0)}, /* CMOTech 6003 */
{QMI_FIXED_INTF(0x16d8, 0x6007, 0)}, /* CMOTech CHE-628S */
{QMI_FIXED_INTF(0x16d8, 0x6008, 0)}, /* CMOTech CMU-301 */
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit aff6db454599d62191aabc208930e891748e4322 ]
__ptr_ring_swap_queue() tries to move pointers from the old
ring to the new one, but it forgets to check if ->producer
is beyond the new size at the end of the operation. This leads
to an out-of-bound access in __ptr_ring_produce() as reported
by syzbot.
Reported-by: [email protected]
Fixes: 5d49de532002 ("ptr_ring: resize support")
Cc: "Michael S. Tsirkin" <[email protected]>
Cc: John Fastabend <[email protected]>
Cc: Jason Wang <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
include/linux/ptr_ring.h | 2 ++
1 file changed, 2 insertions(+)
--- a/include/linux/ptr_ring.h
+++ b/include/linux/ptr_ring.h
@@ -573,6 +573,8 @@ static inline void **__ptr_ring_swap_que
else if (destroy)
destroy(ptr);
+ if (producer >= size)
+ producer = 0;
__ptr_ring_set_size(r, size);
r->producer = producer;
r->consumer_head = 0;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gustavo A. R. Silva <[email protected]>
commit 5ae4f61f012a097df93de2285070ec8e34716d29 upstream.
ipcm->substream is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/pci/emu10k1/emufx.c:1031 snd_emu10k1_ipcm_poke() warn: potential spectre issue 'emu->fx8010.pcm' [r] (local cap)
sound/pci/emu10k1/emufx.c:1075 snd_emu10k1_ipcm_peek() warn: potential spectre issue 'emu->fx8010.pcm' [r] (local cap)
Fix this by sanitizing ipcm->substream before using it to index emu->fx8010.pcm
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: [email protected]
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/emu10k1/emufx.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/sound/pci/emu10k1/emufx.c
+++ b/sound/pci/emu10k1/emufx.c
@@ -36,6 +36,7 @@
#include <linux/init.h>
#include <linux/mutex.h>
#include <linux/moduleparam.h>
+#include <linux/nospec.h>
#include <sound/core.h>
#include <sound/tlv.h>
@@ -1026,6 +1027,8 @@ static int snd_emu10k1_ipcm_poke(struct
if (ipcm->substream >= EMU10K1_FX8010_PCM_COUNT)
return -EINVAL;
+ ipcm->substream = array_index_nospec(ipcm->substream,
+ EMU10K1_FX8010_PCM_COUNT);
if (ipcm->channels > 32)
return -EINVAL;
pcm = &emu->fx8010.pcm[ipcm->substream];
@@ -1072,6 +1075,8 @@ static int snd_emu10k1_ipcm_peek(struct
if (ipcm->substream >= EMU10K1_FX8010_PCM_COUNT)
return -EINVAL;
+ ipcm->substream = array_index_nospec(ipcm->substream,
+ EMU10K1_FX8010_PCM_COUNT);
pcm = &emu->fx8010.pcm[ipcm->substream];
mutex_lock(&emu->fx8010.lock);
spin_lock_irq(&emu->reg_lock);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Theodore Ts'o <[email protected]>
commit a805622a757b6d7f65def4141d29317d8e37b8a1 upstream.
In ext4_expand_extra_isize_ea(), we calculate the total size of the
xattr header, plus the xattr entries so we know how much of the
beginning part of the xattrs to move when expanding the inode extra
size. We need to include the terminating u32 at the end of the xattr
entries, or else if there is uninitialized, non-zero bytes after the
xattr entries and before the xattr values, the list of xattr entries
won't be properly terminated.
Reported-by: Steve Graham <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/xattr.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/fs/ext4/xattr.c
+++ b/fs/ext4/xattr.c
@@ -2725,7 +2725,7 @@ retry:
base = IFIRST(header);
end = (void *)raw_inode + EXT4_SB(inode->i_sb)->s_inode_size;
min_offs = end - base;
- total_ino = sizeof(struct ext4_xattr_ibody_header);
+ total_ino = sizeof(struct ext4_xattr_ibody_header) + sizeof(u32);
error = xattr_check_inode(inode, header, end);
if (error)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Theodore Ts'o <[email protected]>
commit 8a363970d1dc38c4ec4ad575c862f776f468d057 upstream.
If we receive a file handle, either from NFS or open_by_handle_at(2),
and it points at an inode which has not been initialized, and the file
system has metadata checksums enabled, we shouldn't try to get the
inode, discover the checksum is invalid, and then declare the file
system as being inconsistent.
This can be reproduced by creating a test file system via "mke2fs -t
ext4 -O metadata_csum /tmp/foo.img 8M", mounting it, cd'ing into that
directory, and then running the following program.
#define _GNU_SOURCE
#include <fcntl.h>
struct handle {
struct file_handle fh;
unsigned char fid[MAX_HANDLE_SZ];
};
int main(int argc, char **argv)
{
struct handle h = {{8, 1 }, { 12, }};
open_by_handle_at(AT_FDCWD, &h.fh, O_RDONLY);
return 0;
}
Google-Bug-Id: 120690101
Signed-off-by: Theodore Ts'o <[email protected]>
Cc: [email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/ext4.h | 15 +++++++++++++--
fs/ext4/ialloc.c | 2 +-
fs/ext4/inode.c | 54 +++++++++++++++++++++++++++++++++++++-----------------
fs/ext4/ioctl.c | 2 +-
fs/ext4/namei.c | 4 ++--
fs/ext4/resize.c | 5 +++--
fs/ext4/super.c | 19 +++++--------------
fs/ext4/xattr.c | 5 +++--
8 files changed, 65 insertions(+), 41 deletions(-)
--- a/fs/ext4/ext4.h
+++ b/fs/ext4/ext4.h
@@ -2459,8 +2459,19 @@ int do_journal_get_write_access(handle_t
#define FALL_BACK_TO_NONDELALLOC 1
#define CONVERT_INLINE_DATA 2
-extern struct inode *ext4_iget(struct super_block *, unsigned long);
-extern struct inode *ext4_iget_normal(struct super_block *, unsigned long);
+typedef enum {
+ EXT4_IGET_NORMAL = 0,
+ EXT4_IGET_SPECIAL = 0x0001, /* OK to iget a system inode */
+ EXT4_IGET_HANDLE = 0x0002 /* Inode # is from a handle */
+} ext4_iget_flags;
+
+extern struct inode *__ext4_iget(struct super_block *sb, unsigned long ino,
+ ext4_iget_flags flags, const char *function,
+ unsigned int line);
+
+#define ext4_iget(sb, ino, flags) \
+ __ext4_iget((sb), (ino), (flags), __func__, __LINE__)
+
extern int ext4_write_inode(struct inode *, struct writeback_control *);
extern int ext4_setattr(struct dentry *, struct iattr *);
extern int ext4_getattr(const struct path *, struct kstat *, u32, unsigned int);
--- a/fs/ext4/ialloc.c
+++ b/fs/ext4/ialloc.c
@@ -1225,7 +1225,7 @@ struct inode *ext4_orphan_get(struct sup
if (!ext4_test_bit(bit, bitmap_bh->b_data))
goto bad_orphan;
- inode = ext4_iget(sb, ino);
+ inode = ext4_iget(sb, ino, EXT4_IGET_NORMAL);
if (IS_ERR(inode)) {
err = PTR_ERR(inode);
ext4_error(sb, "couldn't read orphan inode %lu (err %d)",
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -4786,7 +4786,9 @@ static inline u64 ext4_inode_peek_iversi
return inode_peek_iversion(inode);
}
-struct inode *ext4_iget(struct super_block *sb, unsigned long ino)
+struct inode *__ext4_iget(struct super_block *sb, unsigned long ino,
+ ext4_iget_flags flags, const char *function,
+ unsigned int line)
{
struct ext4_iloc iloc;
struct ext4_inode *raw_inode;
@@ -4800,6 +4802,18 @@ struct inode *ext4_iget(struct super_blo
gid_t i_gid;
projid_t i_projid;
+ if (((flags & EXT4_IGET_NORMAL) &&
+ (ino < EXT4_FIRST_INO(sb) && ino != EXT4_ROOT_INO)) ||
+ (ino < EXT4_ROOT_INO) ||
+ (ino > le32_to_cpu(EXT4_SB(sb)->s_es->s_inodes_count))) {
+ if (flags & EXT4_IGET_HANDLE)
+ return ERR_PTR(-ESTALE);
+ __ext4_error(sb, function, line,
+ "inode #%lu: comm %s: iget: illegal inode #",
+ ino, current->comm);
+ return ERR_PTR(-EFSCORRUPTED);
+ }
+
inode = iget_locked(sb, ino);
if (!inode)
return ERR_PTR(-ENOMEM);
@@ -4815,18 +4829,26 @@ struct inode *ext4_iget(struct super_blo
raw_inode = ext4_raw_inode(&iloc);
if ((ino == EXT4_ROOT_INO) && (raw_inode->i_links_count == 0)) {
- EXT4_ERROR_INODE(inode, "root inode unallocated");
+ ext4_error_inode(inode, function, line, 0,
+ "iget: root inode unallocated");
ret = -EFSCORRUPTED;
goto bad_inode;
}
+ if ((flags & EXT4_IGET_HANDLE) &&
+ (raw_inode->i_links_count == 0) && (raw_inode->i_mode == 0)) {
+ ret = -ESTALE;
+ goto bad_inode;
+ }
+
if (EXT4_INODE_SIZE(inode->i_sb) > EXT4_GOOD_OLD_INODE_SIZE) {
ei->i_extra_isize = le16_to_cpu(raw_inode->i_extra_isize);
if (EXT4_GOOD_OLD_INODE_SIZE + ei->i_extra_isize >
EXT4_INODE_SIZE(inode->i_sb) ||
(ei->i_extra_isize & 3)) {
- EXT4_ERROR_INODE(inode,
- "bad extra_isize %u (inode size %u)",
+ ext4_error_inode(inode, function, line, 0,
+ "iget: bad extra_isize %u "
+ "(inode size %u)",
ei->i_extra_isize,
EXT4_INODE_SIZE(inode->i_sb));
ret = -EFSCORRUPTED;
@@ -4848,7 +4870,8 @@ struct inode *ext4_iget(struct super_blo
}
if (!ext4_inode_csum_verify(inode, raw_inode, ei)) {
- EXT4_ERROR_INODE(inode, "checksum invalid");
+ ext4_error_inode(inode, function, line, 0,
+ "iget: checksum invalid");
ret = -EFSBADCRC;
goto bad_inode;
}
@@ -4905,7 +4928,8 @@ struct inode *ext4_iget(struct super_blo
((__u64)le16_to_cpu(raw_inode->i_file_acl_high)) << 32;
inode->i_size = ext4_isize(sb, raw_inode);
if ((size = i_size_read(inode)) < 0) {
- EXT4_ERROR_INODE(inode, "bad i_size value: %lld", size);
+ ext4_error_inode(inode, function, line, 0,
+ "iget: bad i_size value: %lld", size);
ret = -EFSCORRUPTED;
goto bad_inode;
}
@@ -4981,7 +5005,8 @@ struct inode *ext4_iget(struct super_blo
ret = 0;
if (ei->i_file_acl &&
!ext4_data_block_valid(EXT4_SB(sb), ei->i_file_acl, 1)) {
- EXT4_ERROR_INODE(inode, "bad extended attribute block %llu",
+ ext4_error_inode(inode, function, line, 0,
+ "iget: bad extended attribute block %llu",
ei->i_file_acl);
ret = -EFSCORRUPTED;
goto bad_inode;
@@ -5009,8 +5034,9 @@ struct inode *ext4_iget(struct super_blo
} else if (S_ISLNK(inode->i_mode)) {
/* VFS does not allow setting these so must be corruption */
if (IS_APPEND(inode) || IS_IMMUTABLE(inode)) {
- EXT4_ERROR_INODE(inode,
- "immutable or append flags not allowed on symlinks");
+ ext4_error_inode(inode, function, line, 0,
+ "iget: immutable or append flags "
+ "not allowed on symlinks");
ret = -EFSCORRUPTED;
goto bad_inode;
}
@@ -5040,7 +5066,8 @@ struct inode *ext4_iget(struct super_blo
make_bad_inode(inode);
} else {
ret = -EFSCORRUPTED;
- EXT4_ERROR_INODE(inode, "bogus i_mode (%o)", inode->i_mode);
+ ext4_error_inode(inode, function, line, 0,
+ "iget: bogus i_mode (%o)", inode->i_mode);
goto bad_inode;
}
brelse(iloc.bh);
@@ -5054,13 +5081,6 @@ bad_inode:
return ERR_PTR(ret);
}
-struct inode *ext4_iget_normal(struct super_block *sb, unsigned long ino)
-{
- if (ino < EXT4_FIRST_INO(sb) && ino != EXT4_ROOT_INO)
- return ERR_PTR(-EFSCORRUPTED);
- return ext4_iget(sb, ino);
-}
-
static int ext4_inode_blocks_set(handle_t *handle,
struct ext4_inode *raw_inode,
struct ext4_inode_info *ei)
--- a/fs/ext4/ioctl.c
+++ b/fs/ext4/ioctl.c
@@ -125,7 +125,7 @@ static long swap_inode_boot_loader(struc
!inode_owner_or_capable(inode) || !capable(CAP_SYS_ADMIN))
return -EPERM;
- inode_bl = ext4_iget(sb, EXT4_BOOT_LOADER_INO);
+ inode_bl = ext4_iget(sb, EXT4_BOOT_LOADER_INO, EXT4_IGET_SPECIAL);
if (IS_ERR(inode_bl))
return PTR_ERR(inode_bl);
ei_bl = EXT4_I(inode_bl);
--- a/fs/ext4/namei.c
+++ b/fs/ext4/namei.c
@@ -1571,7 +1571,7 @@ static struct dentry *ext4_lookup(struct
dentry);
return ERR_PTR(-EFSCORRUPTED);
}
- inode = ext4_iget_normal(dir->i_sb, ino);
+ inode = ext4_iget(dir->i_sb, ino, EXT4_IGET_NORMAL);
if (inode == ERR_PTR(-ESTALE)) {
EXT4_ERROR_INODE(dir,
"deleted inode referenced: %u",
@@ -1613,7 +1613,7 @@ struct dentry *ext4_get_parent(struct de
return ERR_PTR(-EFSCORRUPTED);
}
- return d_obtain_alias(ext4_iget_normal(child->d_sb, ino));
+ return d_obtain_alias(ext4_iget(child->d_sb, ino, EXT4_IGET_NORMAL));
}
/*
--- a/fs/ext4/resize.c
+++ b/fs/ext4/resize.c
@@ -1637,7 +1637,7 @@ int ext4_group_add(struct super_block *s
"No reserved GDT blocks, can't resize");
return -EPERM;
}
- inode = ext4_iget(sb, EXT4_RESIZE_INO);
+ inode = ext4_iget(sb, EXT4_RESIZE_INO, EXT4_IGET_SPECIAL);
if (IS_ERR(inode)) {
ext4_warning(sb, "Error opening resize inode");
return PTR_ERR(inode);
@@ -1965,7 +1965,8 @@ retry:
}
if (!resize_inode)
- resize_inode = ext4_iget(sb, EXT4_RESIZE_INO);
+ resize_inode = ext4_iget(sb, EXT4_RESIZE_INO,
+ EXT4_IGET_SPECIAL);
if (IS_ERR(resize_inode)) {
ext4_warning(sb, "Error opening resize inode");
return PTR_ERR(resize_inode);
--- a/fs/ext4/super.c
+++ b/fs/ext4/super.c
@@ -1173,20 +1173,11 @@ static struct inode *ext4_nfs_get_inode(
{
struct inode *inode;
- if (ino < EXT4_FIRST_INO(sb) && ino != EXT4_ROOT_INO)
- return ERR_PTR(-ESTALE);
- if (ino > le32_to_cpu(EXT4_SB(sb)->s_es->s_inodes_count))
- return ERR_PTR(-ESTALE);
-
- /* iget isn't really right if the inode is currently unallocated!!
- *
- * ext4_read_inode will return a bad_inode if the inode had been
- * deleted, so we should be safe.
- *
+ /*
* Currently we don't know the generation for parent directory, so
* a generation of 0 means "accept any"
*/
- inode = ext4_iget_normal(sb, ino);
+ inode = ext4_iget(sb, ino, EXT4_IGET_HANDLE);
if (IS_ERR(inode))
return ERR_CAST(inode);
if (generation && inode->i_generation != generation) {
@@ -4350,7 +4341,7 @@ no_journal:
* so we can safely mount the rest of the filesystem now.
*/
- root = ext4_iget(sb, EXT4_ROOT_INO);
+ root = ext4_iget(sb, EXT4_ROOT_INO, EXT4_IGET_SPECIAL);
if (IS_ERR(root)) {
ext4_msg(sb, KERN_ERR, "get root inode failed");
ret = PTR_ERR(root);
@@ -4620,7 +4611,7 @@ static struct inode *ext4_get_journal_in
* happen if we iget() an unused inode, as the subsequent iput()
* will try to delete it.
*/
- journal_inode = ext4_iget(sb, journal_inum);
+ journal_inode = ext4_iget(sb, journal_inum, EXT4_IGET_SPECIAL);
if (IS_ERR(journal_inode)) {
ext4_msg(sb, KERN_ERR, "no journal found");
return NULL;
@@ -5702,7 +5693,7 @@ static int ext4_quota_enable(struct supe
if (!qf_inums[type])
return -EPERM;
- qf_inode = ext4_iget(sb, qf_inums[type]);
+ qf_inode = ext4_iget(sb, qf_inums[type], EXT4_IGET_SPECIAL);
if (IS_ERR(qf_inode)) {
ext4_error(sb, "Bad quota inode # %lu", qf_inums[type]);
return PTR_ERR(qf_inode);
--- a/fs/ext4/xattr.c
+++ b/fs/ext4/xattr.c
@@ -384,7 +384,7 @@ static int ext4_xattr_inode_iget(struct
struct inode *inode;
int err;
- inode = ext4_iget(parent->i_sb, ea_ino);
+ inode = ext4_iget(parent->i_sb, ea_ino, EXT4_IGET_NORMAL);
if (IS_ERR(inode)) {
err = PTR_ERR(inode);
ext4_error(parent->i_sb,
@@ -1486,7 +1486,8 @@ ext4_xattr_inode_cache_find(struct inode
}
while (ce) {
- ea_inode = ext4_iget(inode->i_sb, ce->e_value);
+ ea_inode = ext4_iget(inode->i_sb, ce->e_value,
+ EXT4_IGET_NORMAL);
if (!IS_ERR(ea_inode) &&
!is_bad_inode(ea_inode) &&
(EXT4_I(ea_inode)->i_flags & EXT4_EA_INODE_FL) &&
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Wenwen Wang <[email protected]>
commit 7172122be6a4712d699da4d261f92aa5ab3a78b8 upstream.
In crypto_alloc_context(), a DMA pool is allocated through dma_pool_alloc()
to hold the crypto context. The meta data of the DMA pool, including the
pool used for the allocation 'ndev->ctx_pool' and the base address of the
DMA pool used by the device 'dma', are then stored to the beginning of the
pool. These meta data are eventually used in crypto_free_context() to free
the DMA pool through dma_pool_free(). However, given that the DMA pool can
also be accessed by the device, a malicious device can modify these meta
data, especially when the device is controlled to deploy an attack. This
can cause an unexpected DMA pool free failure.
To avoid the above issue, this patch introduces a new structure
crypto_ctx_hdr and a new field chdr in the structure nitrox_crypto_ctx hold
the meta data information of the DMA pool after the allocation. Note that
the original structure ctx_hdr is not changed to ensure the compatibility.
Cc: <[email protected]>
Signed-off-by: Wenwen Wang <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/crypto/cavium/nitrox/nitrox_algs.c | 12 +++++++-----
drivers/crypto/cavium/nitrox/nitrox_lib.c | 22 +++++++++++++++++-----
drivers/crypto/cavium/nitrox/nitrox_req.h | 7 +++++++
3 files changed, 31 insertions(+), 10 deletions(-)
--- a/drivers/crypto/cavium/nitrox/nitrox_algs.c
+++ b/drivers/crypto/cavium/nitrox/nitrox_algs.c
@@ -73,7 +73,7 @@ static int flexi_aes_keylen(int keylen)
static int nitrox_skcipher_init(struct crypto_skcipher *tfm)
{
struct nitrox_crypto_ctx *nctx = crypto_skcipher_ctx(tfm);
- void *fctx;
+ struct crypto_ctx_hdr *chdr;
/* get the first device */
nctx->ndev = nitrox_get_first_device();
@@ -81,12 +81,14 @@ static int nitrox_skcipher_init(struct c
return -ENODEV;
/* allocate nitrox crypto context */
- fctx = crypto_alloc_context(nctx->ndev);
- if (!fctx) {
+ chdr = crypto_alloc_context(nctx->ndev);
+ if (!chdr) {
nitrox_put_device(nctx->ndev);
return -ENOMEM;
}
- nctx->u.ctx_handle = (uintptr_t)fctx;
+ nctx->chdr = chdr;
+ nctx->u.ctx_handle = (uintptr_t)((u8 *)chdr->vaddr +
+ sizeof(struct ctx_hdr));
crypto_skcipher_set_reqsize(tfm, crypto_skcipher_reqsize(tfm) +
sizeof(struct nitrox_kcrypt_request));
return 0;
@@ -102,7 +104,7 @@ static void nitrox_skcipher_exit(struct
memset(&fctx->crypto, 0, sizeof(struct crypto_keys));
memset(&fctx->auth, 0, sizeof(struct auth_keys));
- crypto_free_context((void *)fctx);
+ crypto_free_context((void *)nctx->chdr);
}
nitrox_put_device(nctx->ndev);
--- a/drivers/crypto/cavium/nitrox/nitrox_lib.c
+++ b/drivers/crypto/cavium/nitrox/nitrox_lib.c
@@ -146,12 +146,19 @@ static void destroy_crypto_dma_pool(stru
void *crypto_alloc_context(struct nitrox_device *ndev)
{
struct ctx_hdr *ctx;
+ struct crypto_ctx_hdr *chdr;
void *vaddr;
dma_addr_t dma;
+ chdr = kmalloc(sizeof(*chdr), GFP_KERNEL);
+ if (!chdr)
+ return NULL;
+
vaddr = dma_pool_alloc(ndev->ctx_pool, (GFP_KERNEL | __GFP_ZERO), &dma);
- if (!vaddr)
+ if (!vaddr) {
+ kfree(chdr);
return NULL;
+ }
/* fill meta data */
ctx = vaddr;
@@ -159,7 +166,11 @@ void *crypto_alloc_context(struct nitrox
ctx->dma = dma;
ctx->ctx_dma = dma + sizeof(struct ctx_hdr);
- return ((u8 *)vaddr + sizeof(struct ctx_hdr));
+ chdr->pool = ndev->ctx_pool;
+ chdr->dma = dma;
+ chdr->vaddr = vaddr;
+
+ return chdr;
}
/**
@@ -168,13 +179,14 @@ void *crypto_alloc_context(struct nitrox
*/
void crypto_free_context(void *ctx)
{
- struct ctx_hdr *ctxp;
+ struct crypto_ctx_hdr *ctxp;
if (!ctx)
return;
- ctxp = (struct ctx_hdr *)((u8 *)ctx - sizeof(struct ctx_hdr));
- dma_pool_free(ctxp->pool, ctxp, ctxp->dma);
+ ctxp = ctx;
+ dma_pool_free(ctxp->pool, ctxp->vaddr, ctxp->dma);
+ kfree(ctxp);
}
/**
--- a/drivers/crypto/cavium/nitrox/nitrox_req.h
+++ b/drivers/crypto/cavium/nitrox/nitrox_req.h
@@ -181,12 +181,19 @@ struct flexi_crypto_context {
struct auth_keys auth;
};
+struct crypto_ctx_hdr {
+ struct dma_pool *pool;
+ dma_addr_t dma;
+ void *vaddr;
+};
+
struct nitrox_crypto_ctx {
struct nitrox_device *ndev;
union {
u64 ctx_handle;
struct flexi_crypto_context *fctx;
} u;
+ struct crypto_ctx_hdr *chdr;
};
struct nitrox_kcrypt_request {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Atul Gupta <[email protected]>
commit c35828ea906a7c76632a0211e59c392903cd4615 upstream.
Immediate packets sent to hardware should include the work
request length in calculating the flits. WR occupy one flit and
if not accounted result in invalid request which stalls the HW
queue.
Cc: [email protected]
Signed-off-by: Atul Gupta <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/crypto/chelsio/chcr_ipsec.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/drivers/crypto/chelsio/chcr_ipsec.c
+++ b/drivers/crypto/chelsio/chcr_ipsec.c
@@ -303,7 +303,10 @@ static bool chcr_ipsec_offload_ok(struct
static inline int is_eth_imm(const struct sk_buff *skb, unsigned int kctx_len)
{
- int hdrlen = sizeof(struct chcr_ipsec_req) + kctx_len;
+ int hdrlen;
+
+ hdrlen = sizeof(struct fw_ulptx_wr) +
+ sizeof(struct chcr_ipsec_req) + kctx_len;
hdrlen += sizeof(struct cpl_tx_pkt);
if (skb->len <= MAX_IMM_TX_PKT_LEN - hdrlen)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Josef Bacik <[email protected]>
commit 0568e82dbe2510fc1fa664f58e5c997d3f1e649e upstream.
With my delayed refs patches in place we started seeing a large amount
of aborts in __btrfs_free_extent:
BTRFS error (device sdb1): unable to find ref byte nr 91947008 parent 0 root 35964 owner 1 offset 0
Call Trace:
? btrfs_merge_delayed_refs+0xaf/0x340
__btrfs_run_delayed_refs+0x6ea/0xfc0
? btrfs_set_path_blocking+0x31/0x60
btrfs_run_delayed_refs+0xeb/0x180
btrfs_commit_transaction+0x179/0x7f0
? btrfs_check_space_for_delayed_refs+0x30/0x50
? should_end_transaction.isra.19+0xe/0x40
btrfs_drop_snapshot+0x41c/0x7c0
btrfs_clean_one_deleted_snapshot+0xb5/0xd0
cleaner_kthread+0xf6/0x120
kthread+0xf8/0x130
? btree_invalidatepage+0x90/0x90
? kthread_bind+0x10/0x10
ret_from_fork+0x35/0x40
This was because btrfs_drop_snapshot depends on the root not being
modified while it's dropping the snapshot. It will unlock the root node
(and really every node) as it walks down the tree, only to re-lock it
when it needs to do something. This is a problem because if we modify
the tree we could cow a block in our path, which frees our reference to
that block. Then once we get back to that shared block we'll free our
reference to it again, and get ENOENT when trying to lookup our extent
reference to that block in __btrfs_free_extent.
This is ultimately happening because we have delayed items left to be
processed for our deleted snapshot _after_ all of the inodes are closed
for the snapshot. We only run the delayed inode item if we're deleting
the inode, and even then we do not run the delayed insertions or delayed
removals. These can be run at any point after our final inode does its
last iput, which is what triggers the snapshot deletion. We can end up
with the snapshot deletion happening and then have the delayed items run
on that file system, resulting in the above problem.
This problem has existed forever, however my patches made it much easier
to hit as I wake up the cleaner much more often to deal with delayed
iputs, which made us more likely to start the snapshot dropping work
before the transaction commits, which is when the delayed items would
generally be run. Before, generally speaking, we would run the delayed
items, commit the transaction, and wakeup the cleaner thread to start
deleting snapshots, which means we were less likely to hit this problem.
You could still hit it if you had multiple snapshots to be deleted and
ended up with lots of delayed items, but it was definitely harder.
Fix for now by simply running all the delayed items before starting to
drop the snapshot. We could make this smarter in the future by making
the delayed items per-root, and then simply drop any delayed items for
roots that we are going to delete. But for now just a quick and easy
solution is the safest.
CC: [email protected] # 4.4+
Reviewed-by: Filipe Manana <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/extent-tree.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -8911,6 +8911,10 @@ int btrfs_drop_snapshot(struct btrfs_roo
goto out_free;
}
+ err = btrfs_run_delayed_items(trans);
+ if (err)
+ goto out_end_trans;
+
if (block_rsv)
trans->block_rsv = block_rsv;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Theodore Ts'o <[email protected]>
commit fb265c9cb49e2074ddcdd4de99728aefdd3b3592 upstream.
Today, when sb_bread() returns NULL, this can either be because of an
I/O error or because the system failed to allocate the buffer. Since
it's an old interface, changing would require changing many call
sites.
So instead we create our own ext4_sb_bread(), which also allows us to
set the REQ_META flag.
Also fixed a problem in the xattr code where a NULL return in a
function could also mean that the xattr was not found, which could
lead to the wrong error getting returned to userspace.
Fixes: ac27a0ec112a ("ext4: initial copy of files from ext3")
Cc: [email protected] # 2.6.19
Signed-off-by: Theodore Ts'o <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/ext4.h | 2 +
fs/ext4/migrate.c | 36 ++++++++++++-------------
fs/ext4/resize.c | 72 +++++++++++++++++++++++++--------------------------
fs/ext4/super.c | 23 ++++++++++++++++
fs/ext4/xattr.c | 76 +++++++++++++++++++++++++-----------------------------
5 files changed, 115 insertions(+), 94 deletions(-)
--- a/fs/ext4/ext4.h
+++ b/fs/ext4/ext4.h
@@ -2542,6 +2542,8 @@ extern int ext4_group_extend(struct supe
extern int ext4_resize_fs(struct super_block *sb, ext4_fsblk_t n_blocks_count);
/* super.c */
+extern struct buffer_head *ext4_sb_bread(struct super_block *sb,
+ sector_t block, int op_flags);
extern int ext4_seq_options_show(struct seq_file *seq, void *offset);
extern int ext4_calculate_overhead(struct super_block *sb);
extern void ext4_superblock_csum_set(struct super_block *sb);
--- a/fs/ext4/migrate.c
+++ b/fs/ext4/migrate.c
@@ -116,9 +116,9 @@ static int update_ind_extent_range(handl
int i, retval = 0;
unsigned long max_entries = inode->i_sb->s_blocksize >> 2;
- bh = sb_bread(inode->i_sb, pblock);
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, pblock, 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
i_data = (__le32 *)bh->b_data;
for (i = 0; i < max_entries; i++) {
@@ -145,9 +145,9 @@ static int update_dind_extent_range(hand
int i, retval = 0;
unsigned long max_entries = inode->i_sb->s_blocksize >> 2;
- bh = sb_bread(inode->i_sb, pblock);
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, pblock, 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
i_data = (__le32 *)bh->b_data;
for (i = 0; i < max_entries; i++) {
@@ -175,9 +175,9 @@ static int update_tind_extent_range(hand
int i, retval = 0;
unsigned long max_entries = inode->i_sb->s_blocksize >> 2;
- bh = sb_bread(inode->i_sb, pblock);
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, pblock, 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
i_data = (__le32 *)bh->b_data;
for (i = 0; i < max_entries; i++) {
@@ -224,9 +224,9 @@ static int free_dind_blocks(handle_t *ha
struct buffer_head *bh;
unsigned long max_entries = inode->i_sb->s_blocksize >> 2;
- bh = sb_bread(inode->i_sb, le32_to_cpu(i_data));
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, le32_to_cpu(i_data), 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
tmp_idata = (__le32 *)bh->b_data;
for (i = 0; i < max_entries; i++) {
@@ -254,9 +254,9 @@ static int free_tind_blocks(handle_t *ha
struct buffer_head *bh;
unsigned long max_entries = inode->i_sb->s_blocksize >> 2;
- bh = sb_bread(inode->i_sb, le32_to_cpu(i_data));
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, le32_to_cpu(i_data), 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
tmp_idata = (__le32 *)bh->b_data;
for (i = 0; i < max_entries; i++) {
@@ -382,9 +382,9 @@ static int free_ext_idx(handle_t *handle
struct ext4_extent_header *eh;
block = ext4_idx_pblock(ix);
- bh = sb_bread(inode->i_sb, block);
- if (!bh)
- return -EIO;
+ bh = ext4_sb_bread(inode->i_sb, block, 0);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
eh = (struct ext4_extent_header *)bh->b_data;
if (eh->eh_depth != 0) {
--- a/fs/ext4/resize.c
+++ b/fs/ext4/resize.c
@@ -127,10 +127,12 @@ static int verify_group_input(struct sup
else if (free_blocks_count < 0)
ext4_warning(sb, "Bad blocks count %u",
input->blocks_count);
- else if (!(bh = sb_bread(sb, end - 1)))
+ else if (IS_ERR(bh = ext4_sb_bread(sb, end - 1, 0))) {
+ err = PTR_ERR(bh);
+ bh = NULL;
ext4_warning(sb, "Cannot read last block (%llu)",
end - 1);
- else if (outside(input->block_bitmap, start, end))
+ } else if (outside(input->block_bitmap, start, end))
ext4_warning(sb, "Block bitmap not in group (block %llu)",
(unsigned long long)input->block_bitmap);
else if (outside(input->inode_bitmap, start, end))
@@ -781,11 +783,11 @@ static int add_new_gdb(handle_t *handle,
struct ext4_super_block *es = EXT4_SB(sb)->s_es;
unsigned long gdb_num = group / EXT4_DESC_PER_BLOCK(sb);
ext4_fsblk_t gdblock = EXT4_SB(sb)->s_sbh->b_blocknr + 1 + gdb_num;
- struct buffer_head **o_group_desc, **n_group_desc;
- struct buffer_head *dind;
- struct buffer_head *gdb_bh;
+ struct buffer_head **o_group_desc, **n_group_desc = NULL;
+ struct buffer_head *dind = NULL;
+ struct buffer_head *gdb_bh = NULL;
int gdbackups;
- struct ext4_iloc iloc;
+ struct ext4_iloc iloc = { .bh = NULL };
__le32 *data;
int err;
@@ -794,21 +796,22 @@ static int add_new_gdb(handle_t *handle,
"EXT4-fs: ext4_add_new_gdb: adding group block %lu\n",
gdb_num);
- gdb_bh = sb_bread(sb, gdblock);
- if (!gdb_bh)
- return -EIO;
+ gdb_bh = ext4_sb_bread(sb, gdblock, 0);
+ if (IS_ERR(gdb_bh))
+ return PTR_ERR(gdb_bh);
gdbackups = verify_reserved_gdb(sb, group, gdb_bh);
if (gdbackups < 0) {
err = gdbackups;
- goto exit_bh;
+ goto errout;
}
data = EXT4_I(inode)->i_data + EXT4_DIND_BLOCK;
- dind = sb_bread(sb, le32_to_cpu(*data));
- if (!dind) {
- err = -EIO;
- goto exit_bh;
+ dind = ext4_sb_bread(sb, le32_to_cpu(*data), 0);
+ if (IS_ERR(dind)) {
+ err = PTR_ERR(dind);
+ dind = NULL;
+ goto errout;
}
data = (__le32 *)dind->b_data;
@@ -816,18 +819,18 @@ static int add_new_gdb(handle_t *handle,
ext4_warning(sb, "new group %u GDT block %llu not reserved",
group, gdblock);
err = -EINVAL;
- goto exit_dind;
+ goto errout;
}
BUFFER_TRACE(EXT4_SB(sb)->s_sbh, "get_write_access");
err = ext4_journal_get_write_access(handle, EXT4_SB(sb)->s_sbh);
if (unlikely(err))
- goto exit_dind;
+ goto errout;
BUFFER_TRACE(gdb_bh, "get_write_access");
err = ext4_journal_get_write_access(handle, gdb_bh);
if (unlikely(err))
- goto exit_dind;
+ goto errout;
BUFFER_TRACE(dind, "get_write_access");
err = ext4_journal_get_write_access(handle, dind);
@@ -837,7 +840,7 @@ static int add_new_gdb(handle_t *handle,
/* ext4_reserve_inode_write() gets a reference on the iloc */
err = ext4_reserve_inode_write(handle, inode, &iloc);
if (unlikely(err))
- goto exit_dind;
+ goto errout;
n_group_desc = ext4_kvmalloc((gdb_num + 1) *
sizeof(struct buffer_head *),
@@ -846,7 +849,7 @@ static int add_new_gdb(handle_t *handle,
err = -ENOMEM;
ext4_warning(sb, "not enough memory for %lu groups",
gdb_num + 1);
- goto exit_inode;
+ goto errout;
}
/*
@@ -862,7 +865,7 @@ static int add_new_gdb(handle_t *handle,
err = ext4_handle_dirty_metadata(handle, NULL, dind);
if (unlikely(err)) {
ext4_std_error(sb, err);
- goto exit_inode;
+ goto errout;
}
inode->i_blocks -= (gdbackups + 1) * sb->s_blocksize >>
(9 - EXT4_SB(sb)->s_cluster_bits);
@@ -871,8 +874,7 @@ static int add_new_gdb(handle_t *handle,
err = ext4_handle_dirty_metadata(handle, NULL, gdb_bh);
if (unlikely(err)) {
ext4_std_error(sb, err);
- iloc.bh = NULL;
- goto exit_inode;
+ goto errout;
}
brelse(dind);
@@ -888,15 +890,11 @@ static int add_new_gdb(handle_t *handle,
err = ext4_handle_dirty_super(handle, sb);
if (err)
ext4_std_error(sb, err);
-
return err;
-
-exit_inode:
+errout:
kvfree(n_group_desc);
brelse(iloc.bh);
-exit_dind:
brelse(dind);
-exit_bh:
brelse(gdb_bh);
ext4_debug("leaving with error %d\n", err);
@@ -916,9 +914,9 @@ static int add_new_gdb_meta_bg(struct su
gdblock = ext4_meta_bg_first_block_no(sb, group) +
ext4_bg_has_super(sb, group);
- gdb_bh = sb_bread(sb, gdblock);
- if (!gdb_bh)
- return -EIO;
+ gdb_bh = ext4_sb_bread(sb, gdblock, 0);
+ if (IS_ERR(gdb_bh))
+ return PTR_ERR(gdb_bh);
n_group_desc = ext4_kvmalloc((gdb_num + 1) *
sizeof(struct buffer_head *),
GFP_NOFS);
@@ -975,9 +973,10 @@ static int reserve_backup_gdb(handle_t *
return -ENOMEM;
data = EXT4_I(inode)->i_data + EXT4_DIND_BLOCK;
- dind = sb_bread(sb, le32_to_cpu(*data));
- if (!dind) {
- err = -EIO;
+ dind = ext4_sb_bread(sb, le32_to_cpu(*data), 0);
+ if (IS_ERR(dind)) {
+ err = PTR_ERR(dind);
+ dind = NULL;
goto exit_free;
}
@@ -996,9 +995,10 @@ static int reserve_backup_gdb(handle_t *
err = -EINVAL;
goto exit_bh;
}
- primary[res] = sb_bread(sb, blk);
- if (!primary[res]) {
- err = -EIO;
+ primary[res] = ext4_sb_bread(sb, blk, 0);
+ if (IS_ERR(primary[res])) {
+ err = PTR_ERR(primary[res]);
+ primary[res] = NULL;
goto exit_bh;
}
gdbackups = verify_reserved_gdb(sb, group, primary[res]);
--- a/fs/ext4/super.c
+++ b/fs/ext4/super.c
@@ -140,6 +140,29 @@ MODULE_ALIAS_FS("ext3");
MODULE_ALIAS("ext3");
#define IS_EXT3_SB(sb) ((sb)->s_bdev->bd_holder == &ext3_fs_type)
+/*
+ * This works like sb_bread() except it uses ERR_PTR for error
+ * returns. Currently with sb_bread it's impossible to distinguish
+ * between ENOMEM and EIO situations (since both result in a NULL
+ * return.
+ */
+struct buffer_head *
+ext4_sb_bread(struct super_block *sb, sector_t block, int op_flags)
+{
+ struct buffer_head *bh = sb_getblk(sb, block);
+
+ if (bh == NULL)
+ return ERR_PTR(-ENOMEM);
+ if (buffer_uptodate(bh))
+ return bh;
+ ll_rw_block(REQ_OP_READ, REQ_META | op_flags, 1, &bh);
+ wait_on_buffer(bh);
+ if (buffer_uptodate(bh))
+ return bh;
+ put_bh(bh);
+ return ERR_PTR(-EIO);
+}
+
static int ext4_verify_csum_type(struct super_block *sb,
struct ext4_super_block *es)
{
--- a/fs/ext4/xattr.c
+++ b/fs/ext4/xattr.c
@@ -522,14 +522,13 @@ ext4_xattr_block_get(struct inode *inode
ea_idebug(inode, "name=%d.%s, buffer=%p, buffer_size=%ld",
name_index, name, buffer, (long)buffer_size);
- error = -ENODATA;
if (!EXT4_I(inode)->i_file_acl)
- goto cleanup;
+ return -ENODATA;
ea_idebug(inode, "reading block %llu",
(unsigned long long)EXT4_I(inode)->i_file_acl);
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- if (!bh)
- goto cleanup;
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
ea_bdebug(bh, "b_count=%d, refcount=%d",
atomic_read(&(bh->b_count)), le32_to_cpu(BHDR(bh)->h_refcount));
error = ext4_xattr_check_block(inode, bh);
@@ -696,26 +695,23 @@ ext4_xattr_block_list(struct dentry *den
ea_idebug(inode, "buffer=%p, buffer_size=%ld",
buffer, (long)buffer_size);
- error = 0;
if (!EXT4_I(inode)->i_file_acl)
- goto cleanup;
+ return 0;
ea_idebug(inode, "reading block %llu",
(unsigned long long)EXT4_I(inode)->i_file_acl);
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- error = -EIO;
- if (!bh)
- goto cleanup;
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh))
+ return PTR_ERR(bh);
ea_bdebug(bh, "b_count=%d, refcount=%d",
atomic_read(&(bh->b_count)), le32_to_cpu(BHDR(bh)->h_refcount));
error = ext4_xattr_check_block(inode, bh);
if (error)
goto cleanup;
ext4_xattr_block_cache_insert(EA_BLOCK_CACHE(inode), bh);
- error = ext4_xattr_list_entries(dentry, BFIRST(bh), buffer, buffer_size);
-
+ error = ext4_xattr_list_entries(dentry, BFIRST(bh), buffer,
+ buffer_size);
cleanup:
brelse(bh);
-
return error;
}
@@ -830,9 +826,9 @@ int ext4_get_inode_usage(struct inode *i
}
if (EXT4_I(inode)->i_file_acl) {
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- if (!bh) {
- ret = -EIO;
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh)) {
+ ret = PTR_ERR(bh);
goto out;
}
@@ -1825,16 +1821,15 @@ ext4_xattr_block_find(struct inode *inod
if (EXT4_I(inode)->i_file_acl) {
/* The inode already has an extended attribute block. */
- bs->bh = sb_bread(sb, EXT4_I(inode)->i_file_acl);
- error = -EIO;
- if (!bs->bh)
- goto cleanup;
+ bs->bh = ext4_sb_bread(sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bs->bh))
+ return PTR_ERR(bs->bh);
ea_bdebug(bs->bh, "b_count=%d, refcount=%d",
atomic_read(&(bs->bh->b_count)),
le32_to_cpu(BHDR(bs->bh)->h_refcount));
error = ext4_xattr_check_block(inode, bs->bh);
if (error)
- goto cleanup;
+ return error;
/* Find the named attribute. */
bs->s.base = BHDR(bs->bh);
bs->s.first = BFIRST(bs->bh);
@@ -1843,13 +1838,10 @@ ext4_xattr_block_find(struct inode *inod
error = xattr_find_entry(inode, &bs->s.here, bs->s.end,
i->name_index, i->name, 1);
if (error && error != -ENODATA)
- goto cleanup;
+ return error;
bs->s.not_found = error;
}
- error = 0;
-
-cleanup:
- return error;
+ return 0;
}
static int
@@ -2278,9 +2270,9 @@ static struct buffer_head *ext4_xattr_ge
if (!EXT4_I(inode)->i_file_acl)
return NULL;
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- if (!bh)
- return ERR_PTR(-EIO);
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh))
+ return bh;
error = ext4_xattr_check_block(inode, bh);
if (error) {
brelse(bh);
@@ -2750,10 +2742,11 @@ retry:
if (EXT4_I(inode)->i_file_acl) {
struct buffer_head *bh;
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- error = -EIO;
- if (!bh)
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh)) {
+ error = PTR_ERR(bh);
goto cleanup;
+ }
error = ext4_xattr_check_block(inode, bh);
if (error) {
brelse(bh);
@@ -2907,11 +2900,12 @@ int ext4_xattr_delete_inode(handle_t *ha
}
if (EXT4_I(inode)->i_file_acl) {
- bh = sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl);
- if (!bh) {
- EXT4_ERROR_INODE(inode, "block %llu read error",
- EXT4_I(inode)->i_file_acl);
- error = -EIO;
+ bh = ext4_sb_bread(inode->i_sb, EXT4_I(inode)->i_file_acl, REQ_PRIO);
+ if (IS_ERR(bh)) {
+ error = PTR_ERR(bh);
+ if (error == -EIO)
+ EXT4_ERROR_INODE(inode, "block %llu read error",
+ EXT4_I(inode)->i_file_acl);
goto cleanup;
}
error = ext4_xattr_check_block(inode, bh);
@@ -3064,8 +3058,10 @@ ext4_xattr_block_cache_find(struct inode
while (ce) {
struct buffer_head *bh;
- bh = sb_bread(inode->i_sb, ce->e_value);
- if (!bh) {
+ bh = ext4_sb_bread(inode->i_sb, ce->e_value, REQ_PRIO);
+ if (IS_ERR(bh)) {
+ if (PTR_ERR(bh) == -ENOMEM)
+ return NULL;
EXT4_ERROR_INODE(inode, "block %lu read error",
(unsigned long)ce->e_value);
} else if (ext4_xattr_cmp(header, BHDR(bh)) == 0) {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Breno Leitao <[email protected]>
commit 6f5b9f018f4c7686fd944d920209d1382d320e4e upstream.
There is a TM Bad Thing bug that can be caused when you return from a
signal context in a suspended transaction but with ucontext MSR[TS] unset.
This forces regs->msr[TS] to be set at syscall entrance (since the CPU
state is transactional). It also calls treclaim() to flush the transaction
state, which is done based on the live (mfmsr) MSR state.
Since user context MSR[TS] is not set, then restore_tm_sigcontexts() is not
called, thus, not executing recheckpoint, keeping the CPU state as not
transactional. When calling rfid, SRR1 will have MSR[TS] set, but the CPU
state is non transactional, causing the TM Bad Thing with the following
stack:
[ 33.862316] Bad kernel stack pointer 3fffd9dce3e0 at c00000000000c47c
cpu 0x8: Vector: 700 (Program Check) at [c00000003ff7fd40]
pc: c00000000000c47c: fast_exception_return+0xac/0xb4
lr: 00003fff865f442c
sp: 3fffd9dce3e0
msr: 8000000102a03031
current = 0xc00000041f68b700
paca = 0xc00000000fb84800 softe: 0 irq_happened: 0x01
pid = 1721, comm = tm-signal-sigre
Linux version 4.9.0-3-powerpc64le ([email protected]) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
WARNING: exception is not recoverable, can't continue
The same problem happens on 32-bits signal handler, and the fix is very
similar, if tm_recheckpoint() is not executed, then regs->msr[TS] should be
zeroed.
This patch also fixes a sparse warning related to lack of indentation when
CONFIG_PPC_TRANSACTIONAL_MEM is set.
Fixes: 2b0a576d15e0e ("powerpc: Add new transactional memory state to the signal context")
CC: Stable <[email protected]> # 3.10+
Signed-off-by: Breno Leitao <[email protected]>
Tested-by: Michal Suchánek <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/powerpc/kernel/signal_32.c | 18 +++++++++++++-----
arch/powerpc/kernel/signal_64.c | 20 ++++++++++++++++----
2 files changed, 29 insertions(+), 9 deletions(-)
--- a/arch/powerpc/kernel/signal_32.c
+++ b/arch/powerpc/kernel/signal_32.c
@@ -1158,11 +1158,11 @@ SYSCALL_DEFINE0(rt_sigreturn)
{
struct rt_sigframe __user *rt_sf;
struct pt_regs *regs = current_pt_regs();
+ int tm_restore = 0;
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
struct ucontext __user *uc_transact;
unsigned long msr_hi;
unsigned long tmp;
- int tm_restore = 0;
#endif
/* Always make any pending restarted system calls return -EINTR */
current->restart_block.fn = do_no_restart_syscall;
@@ -1210,11 +1210,19 @@ SYSCALL_DEFINE0(rt_sigreturn)
goto bad;
}
}
- if (!tm_restore)
- /* Fall through, for non-TM restore */
+ if (!tm_restore) {
+ /*
+ * Unset regs->msr because ucontext MSR TS is not
+ * set, and recheckpoint was not called. This avoid
+ * hitting a TM Bad thing at RFID
+ */
+ regs->msr &= ~MSR_TS_MASK;
+ }
+ /* Fall through, for non-TM restore */
#endif
- if (do_setcontext(&rt_sf->uc, regs, 1))
- goto bad;
+ if (!tm_restore)
+ if (do_setcontext(&rt_sf->uc, regs, 1))
+ goto bad;
/*
* It's not clear whether or why it is desirable to save the
--- a/arch/powerpc/kernel/signal_64.c
+++ b/arch/powerpc/kernel/signal_64.c
@@ -756,11 +756,23 @@ SYSCALL_DEFINE0(rt_sigreturn)
&uc_transact->uc_mcontext))
goto badframe;
}
- else
- /* Fall through, for non-TM restore */
#endif
- if (restore_sigcontext(current, NULL, 1, &uc->uc_mcontext))
- goto badframe;
+ /* Fall through, for non-TM restore */
+ if (!MSR_TM_ACTIVE(msr)) {
+ /*
+ * Unset MSR[TS] on the thread regs since MSR from user
+ * context does not have MSR active, and recheckpoint was
+ * not called since restore_tm_sigcontexts() was not called
+ * also.
+ *
+ * If not unsetting it, the code can RFID to userspace with
+ * MSR[TS] set, but without CPU in the proper state,
+ * causing a TM bad thing.
+ */
+ current->thread.regs->msr &= ~MSR_TS_MASK;
+ if (restore_sigcontext(current, NULL, 1, &uc->uc_mcontext))
+ goto badframe;
+ }
if (restore_altstack(&uc->uc_stack))
goto badframe;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huacai Chen <[email protected]>
commit bec0de4cfad21bd284dbddee016ed1767a5d2823 upstream.
KEXEC needs the new kernel's load address to be aligned on a page
boundary (see sanity_check_segment_list()), but on MIPS the default
vmlinuz load address is only explicitly aligned to 16 bytes.
Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase
the alignment calculated by calc_vmlinuz_load_addr to 64KB.
Signed-off-by: Huacai Chen <[email protected]>
Signed-off-by: Paul Burton <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/21131/
Cc: Ralf Baechle <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Steven J . Hill <[email protected]>
Cc: [email protected]
Cc: Fuxin Zhang <[email protected]>
Cc: Zhangjin Wu <[email protected]>
Cc: <[email protected]> # 2.6.36+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c | 7 ++++---
1 file changed, 4 insertions(+), 3 deletions(-)
--- a/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c
+++ b/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c
@@ -13,6 +13,7 @@
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
+#include "../../../../include/linux/sizes.h"
int main(int argc, char *argv[])
{
@@ -45,11 +46,11 @@ int main(int argc, char *argv[])
vmlinuz_load_addr = vmlinux_load_addr + vmlinux_size;
/*
- * Align with 16 bytes: "greater than that used for any standard data
- * types by a MIPS compiler." -- See MIPS Run Linux (Second Edition).
+ * Align with 64KB: KEXEC needs load sections to be aligned to PAGE_SIZE,
+ * which may be as large as 64KB depending on the kernel configuration.
*/
- vmlinuz_load_addr += (16 - vmlinux_size % 16);
+ vmlinuz_load_addr += (SZ_64K - vmlinux_size % SZ_64K);
printf("0x%llx\n", vmlinuz_load_addr);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Huacai Chen <[email protected]>
commit bb53fdf395eed103f85061bfff3b116cee123895 upstream.
For multi-node Loongson-3 (NUMA configuration), r4k_blast_scache() can
only flush Node-0's scache. So we add r4k_blast_scache_node() by using
(CAC_BASE | (node_id << NODE_ADDRSPACE_SHIFT)) instead of CKSEG0 as the
start address.
Signed-off-by: Huacai Chen <[email protected]>
[[email protected]: Include asm/mmzone.h from asm/r4kcache.h for
nid_to_addrbase(). Add asm/mach-generic/mmzone.h
to allow inclusion for all platforms.]
Signed-off-by: Paul Burton <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/21129/
Cc: Ralf Baechle <[email protected]>
Cc: James Hogan <[email protected]>
Cc: Steven J . Hill <[email protected]>
Cc: [email protected]
Cc: Fuxin Zhang <[email protected]>
Cc: Zhangjin Wu <[email protected]>
Cc: <[email protected]> # 3.15+
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/mips/include/asm/mach-generic/mmzone.h | 2 +
arch/mips/include/asm/mach-loongson64/mmzone.h | 1
arch/mips/include/asm/mmzone.h | 8 ++++
arch/mips/include/asm/r4kcache.h | 22 ++++++++++++
arch/mips/mm/c-r4k.c | 44 +++++++++++++++++++++----
5 files changed, 70 insertions(+), 7 deletions(-)
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/mmzone.h
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Intentionally empty */
--- a/arch/mips/include/asm/mach-loongson64/mmzone.h
+++ b/arch/mips/include/asm/mach-loongson64/mmzone.h
@@ -21,6 +21,7 @@
#define NODE3_ADDRSPACE_OFFSET 0x300000000000UL
#define pa_to_nid(addr) (((addr) & 0xf00000000000) >> NODE_ADDRSPACE_SHIFT)
+#define nid_to_addrbase(nid) ((nid) << NODE_ADDRSPACE_SHIFT)
#define LEVELS_PER_SLICE 128
--- a/arch/mips/include/asm/mmzone.h
+++ b/arch/mips/include/asm/mmzone.h
@@ -9,6 +9,14 @@
#include <asm/page.h>
#include <mmzone.h>
+#ifndef pa_to_nid
+#define pa_to_nid(addr) 0
+#endif
+
+#ifndef nid_to_addrbase
+#define nid_to_addrbase(nid) 0
+#endif
+
#ifdef CONFIG_DISCONTIGMEM
#define pfn_to_nid(pfn) pa_to_nid((pfn) << PAGE_SHIFT)
--- a/arch/mips/include/asm/r4kcache.h
+++ b/arch/mips/include/asm/r4kcache.h
@@ -20,6 +20,7 @@
#include <asm/cpu-features.h>
#include <asm/cpu-type.h>
#include <asm/mipsmtregs.h>
+#include <asm/mmzone.h>
#include <linux/uaccess.h> /* for uaccess_kernel() */
extern void (*r4k_blast_dcache)(void);
@@ -747,4 +748,25 @@ __BUILD_BLAST_CACHE_RANGE(s, scache, Hit
__BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, , )
__BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, , )
+/* Currently, this is very specific to Loongson-3 */
+#define __BUILD_BLAST_CACHE_NODE(pfx, desc, indexop, hitop, lsize) \
+static inline void blast_##pfx##cache##lsize##_node(long node) \
+{ \
+ unsigned long start = CAC_BASE | nid_to_addrbase(node); \
+ unsigned long end = start + current_cpu_data.desc.waysize; \
+ unsigned long ws_inc = 1UL << current_cpu_data.desc.waybit; \
+ unsigned long ws_end = current_cpu_data.desc.ways << \
+ current_cpu_data.desc.waybit; \
+ unsigned long ws, addr; \
+ \
+ for (ws = 0; ws < ws_end; ws += ws_inc) \
+ for (addr = start; addr < end; addr += lsize * 32) \
+ cache##lsize##_unroll32(addr|ws, indexop); \
+}
+
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128)
+
#endif /* _ASM_R4KCACHE_H */
--- a/arch/mips/mm/c-r4k.c
+++ b/arch/mips/mm/c-r4k.c
@@ -459,11 +459,28 @@ static void r4k_blast_scache_setup(void)
r4k_blast_scache = blast_scache128;
}
+static void (*r4k_blast_scache_node)(long node);
+
+static void r4k_blast_scache_node_setup(void)
+{
+ unsigned long sc_lsize = cpu_scache_line_size();
+
+ if (current_cpu_type() != CPU_LOONGSON3)
+ r4k_blast_scache_node = (void *)cache_noop;
+ else if (sc_lsize == 16)
+ r4k_blast_scache_node = blast_scache16_node;
+ else if (sc_lsize == 32)
+ r4k_blast_scache_node = blast_scache32_node;
+ else if (sc_lsize == 64)
+ r4k_blast_scache_node = blast_scache64_node;
+ else if (sc_lsize == 128)
+ r4k_blast_scache_node = blast_scache128_node;
+}
+
static inline void local_r4k___flush_cache_all(void * args)
{
switch (current_cpu_type()) {
case CPU_LOONGSON2:
- case CPU_LOONGSON3:
case CPU_R4000SC:
case CPU_R4000MC:
case CPU_R4400SC:
@@ -480,6 +497,11 @@ static inline void local_r4k___flush_cac
r4k_blast_scache();
break;
+ case CPU_LOONGSON3:
+ /* Use get_ebase_cpunum() for both NUMA=y/n */
+ r4k_blast_scache_node(get_ebase_cpunum() >> 2);
+ break;
+
case CPU_BMIPS5000:
r4k_blast_scache();
__sync();
@@ -840,10 +862,14 @@ static void r4k_dma_cache_wback_inv(unsi
preempt_disable();
if (cpu_has_inclusive_pcaches) {
- if (size >= scache_size)
- r4k_blast_scache();
- else
+ if (size >= scache_size) {
+ if (current_cpu_type() != CPU_LOONGSON3)
+ r4k_blast_scache();
+ else
+ r4k_blast_scache_node(pa_to_nid(addr));
+ } else {
blast_scache_range(addr, addr + size);
+ }
preempt_enable();
__sync();
return;
@@ -877,9 +903,12 @@ static void r4k_dma_cache_inv(unsigned l
preempt_disable();
if (cpu_has_inclusive_pcaches) {
- if (size >= scache_size)
- r4k_blast_scache();
- else {
+ if (size >= scache_size) {
+ if (current_cpu_type() != CPU_LOONGSON3)
+ r4k_blast_scache();
+ else
+ r4k_blast_scache_node(pa_to_nid(addr));
+ } else {
/*
* There is no clearly documented alignment requirement
* for the cache instruction on MIPS processors and
@@ -1918,6 +1947,7 @@ void r4k_cache_init(void)
r4k_blast_scache_page_setup();
r4k_blast_scache_page_indexed_setup();
r4k_blast_scache_setup();
+ r4k_blast_scache_node_setup();
#ifdef CONFIG_EVA
r4k_blast_dcache_user_page_setup();
r4k_blast_icache_user_page_setup();
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Paul Aurich <[email protected]>
commit 6d2f84eee098540ae857998fe32f29b9e2cd9613 upstream.
When passing a large read to receive_encrypted_read(), ensure that the
demultiplex_thread knows that a MID was processed. Without this, those
operations never complete.
This is a similar issue/fix to lease break handling:
commit 7af929d6d05ba5564139718e30d5bc96bdbc716a
("smb3: fix lease break problem introduced by compounding")
CC: Stable <[email protected]> # 4.19+
Fixes: b24df3e30cbf ("cifs: update receive_encrypted_standard to handle compounded responses")
Signed-off-by: Paul Aurich <[email protected]>
Tested-by: Yves-Alexis Perez <[email protected]>
Signed-off-by: Steve French <[email protected]>
Reviewed-by: Ronnie Sahlberg <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/cifs/smb2ops.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/fs/cifs/smb2ops.c
+++ b/fs/cifs/smb2ops.c
@@ -3184,8 +3184,10 @@ smb3_receive_transform(struct TCP_Server
}
/* TODO: add support for compounds containing READ. */
- if (pdu_length > CIFSMaxBufSize + MAX_HEADER_SIZE(server))
+ if (pdu_length > CIFSMaxBufSize + MAX_HEADER_SIZE(server)) {
+ *num_mids = 1;
return receive_encrypted_read(server, &mids[0]);
+ }
return receive_encrypted_standard(server, mids, bufs, num_mids);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans Verkuil <[email protected]>
commit 32804fcb612bf867034a093f459415e485cf044b upstream.
I noticed that repeatedly running 'cec-ctl --playback' would occasionally
select 'Playback Device 2' instead of 'Playback Device 1', even though there
were no other Playback devices in the HDMI topology. This happened both with
'real' hardware and with the vivid CEC emulation, suggesting that this was an
issue in the core code that claims a logical address.
What 'cec-ctl --playback' does is to first clear all existing logical addresses,
and immediately after that configure the new desired device type.
The core code will poll the logical addresses trying to find a free address.
When found it will issue a few standard messages as per the CEC spec and return.
Those messages are queued up and will be transmitted asynchronously.
What happens is that if you run two 'cec-ctl --playback' commands in quick
succession, there is still a message of the first cec-ctl command being transmitted
when you reconfigure the adapter again in the second cec-ctl command.
When the logical addresses are cleared, then all information about outstanding
transmits inside the CEC core is also cleared, and the core is no longer aware
that there is still a transmit in flight.
When the hardware finishes the transmit it calls transmit_done and the CEC core
thinks it is actually in response of a POLL messages that is trying to find a
free logical address. The result of all this is that the core thinks that the
logical address for Playback Device 1 is in use, when it is really an earlier
transmit that ended.
The main transmit thread looks at adap->transmitting to check if a transmit
is in progress, but that is set to NULL when the adapter is unconfigured.
adap->transmitting represents the view of userspace, not that of the hardware.
So when unconfiguring the adapter the message is marked aborted from the point
of view of userspace, but seen from the PoV of the hardware it is still ongoing.
So introduce a new bool transmit_in_progress that represents the hardware state
and use that instead of adap->transmitting. Now the CEC core waits until the
hardware finishes the transmit before starting a new transmit.
Signed-off-by: Hans Verkuil <[email protected]>
Cc: <[email protected]> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/cec/cec-adap.c | 27 ++++++++++++++++++---------
include/media/cec.h | 1 +
2 files changed, 19 insertions(+), 9 deletions(-)
--- a/drivers/media/cec/cec-adap.c
+++ b/drivers/media/cec/cec-adap.c
@@ -442,7 +442,7 @@ int cec_thread_func(void *_adap)
(adap->needs_hpd &&
(!adap->is_configured && !adap->is_configuring)) ||
kthread_should_stop() ||
- (!adap->transmitting &&
+ (!adap->transmit_in_progress &&
!list_empty(&adap->transmit_queue)),
msecs_to_jiffies(CEC_XFER_TIMEOUT_MS));
timeout = err == 0;
@@ -450,7 +450,7 @@ int cec_thread_func(void *_adap)
/* Otherwise we just wait for something to happen. */
wait_event_interruptible(adap->kthread_waitq,
kthread_should_stop() ||
- (!adap->transmitting &&
+ (!adap->transmit_in_progress &&
!list_empty(&adap->transmit_queue)));
}
@@ -475,6 +475,7 @@ int cec_thread_func(void *_adap)
pr_warn("cec-%s: message %*ph timed out\n", adap->name,
adap->transmitting->msg.len,
adap->transmitting->msg.msg);
+ adap->transmit_in_progress = false;
adap->tx_timeouts++;
/* Just give up on this. */
cec_data_cancel(adap->transmitting,
@@ -486,7 +487,7 @@ int cec_thread_func(void *_adap)
* If we are still transmitting, or there is nothing new to
* transmit, then just continue waiting.
*/
- if (adap->transmitting || list_empty(&adap->transmit_queue))
+ if (adap->transmit_in_progress || list_empty(&adap->transmit_queue))
goto unlock;
/* Get a new message to transmit */
@@ -532,6 +533,8 @@ int cec_thread_func(void *_adap)
if (adap->ops->adap_transmit(adap, data->attempts,
signal_free_time, &data->msg))
cec_data_cancel(data, CEC_TX_STATUS_ABORTED);
+ else
+ adap->transmit_in_progress = true;
unlock:
mutex_unlock(&adap->lock);
@@ -562,14 +565,17 @@ void cec_transmit_done_ts(struct cec_ada
data = adap->transmitting;
if (!data) {
/*
- * This can happen if a transmit was issued and the cable is
+ * This might happen if a transmit was issued and the cable is
* unplugged while the transmit is ongoing. Ignore this
* transmit in that case.
*/
- dprintk(1, "%s was called without an ongoing transmit!\n",
- __func__);
- goto unlock;
+ if (!adap->transmit_in_progress)
+ dprintk(1, "%s was called without an ongoing transmit!\n",
+ __func__);
+ adap->transmit_in_progress = false;
+ goto wake_thread;
}
+ adap->transmit_in_progress = false;
msg = &data->msg;
@@ -635,7 +641,6 @@ wake_thread:
* for transmitting or to retry the current message.
*/
wake_up_interruptible(&adap->kthread_waitq);
-unlock:
mutex_unlock(&adap->lock);
}
EXPORT_SYMBOL_GPL(cec_transmit_done_ts);
@@ -1483,8 +1488,11 @@ void __cec_s_phys_addr(struct cec_adapte
if (adap->monitor_all_cnt)
WARN_ON(call_op(adap, adap_monitor_all_enable, false));
mutex_lock(&adap->devnode.lock);
- if (adap->needs_hpd || list_empty(&adap->devnode.fhs))
+ if (adap->needs_hpd || list_empty(&adap->devnode.fhs)) {
WARN_ON(adap->ops->adap_enable(adap, false));
+ adap->transmit_in_progress = false;
+ wake_up_interruptible(&adap->kthread_waitq);
+ }
mutex_unlock(&adap->devnode.lock);
if (phys_addr == CEC_PHYS_ADDR_INVALID)
return;
@@ -1492,6 +1500,7 @@ void __cec_s_phys_addr(struct cec_adapte
mutex_lock(&adap->devnode.lock);
adap->last_initiator = 0xff;
+ adap->transmit_in_progress = false;
if ((adap->needs_hpd || list_empty(&adap->devnode.fhs)) &&
adap->ops->adap_enable(adap, true)) {
--- a/include/media/cec.h
+++ b/include/media/cec.h
@@ -155,6 +155,7 @@ struct cec_adapter {
unsigned int transmit_queue_sz;
struct list_head wait_queue;
struct cec_data *transmitting;
+ bool transmit_in_progress;
struct task_struct *kthread_config;
struct completion config_completion;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Maurizio Lombardi <[email protected]>
commit 132d00becb31e88469334e1e62751c81345280e0 upstream.
In case of error, ext4_try_to_write_inline_data() should unlock
and release the page it holds.
Fixes: f19d5870cbf7 ("ext4: add normal write support for inline data")
Cc: [email protected] # 3.8
Signed-off-by: Maurizio Lombardi <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/ext4/inline.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
--- a/fs/ext4/inline.c
+++ b/fs/ext4/inline.c
@@ -705,8 +705,11 @@ int ext4_try_to_write_inline_data(struct
if (!PageUptodate(page)) {
ret = ext4_read_inline_page(inode, page);
- if (ret < 0)
+ if (ret < 0) {
+ unlock_page(page);
+ put_page(page);
goto out_up_read;
+ }
}
ret = 1;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Will Deacon <[email protected]>
commit df655b75c43fba0f2621680ab261083297fd6d16 upstream.
Although bit 31 of VTCR_EL2 is RES1, we inadvertently end up setting all
of the upper 32 bits to 1 as well because we define VTCR_EL2_RES1 as
signed, which is sign-extended when assigning to kvm->arch.vtcr.
Lucky for us, the architecture currently treats these upper bits as RES0
so, whilst we've been naughty, we haven't set fire to anything yet.
Cc: <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Christoffer Dall <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm64/include/asm/kvm_arm.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/arm64/include/asm/kvm_arm.h
+++ b/arch/arm64/include/asm/kvm_arm.h
@@ -104,7 +104,7 @@
TCR_EL2_ORGN0_MASK | TCR_EL2_IRGN0_MASK | TCR_EL2_T0SZ_MASK)
/* VTCR_EL2 Registers bits */
-#define VTCR_EL2_RES1 (1 << 31)
+#define VTCR_EL2_RES1 (1U << 31)
#define VTCR_EL2_HD (1 << 22)
#define VTCR_EL2_HA (1 << 21)
#define VTCR_EL2_PS_MASK TCR_EL2_PS_MASK
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans Verkuil <[email protected]>
commit e5f71a27fa12c1a1b02ad478a568e76260f1815e upstream.
text[s] is a signed char, so using that as index into the font8x16 array
can result in negative indices. Cast it to u8 to be safe.
Signed-off-by: Hans Verkuil <[email protected]>
Reported-by: [email protected]
Cc: <[email protected]> # for v4.7 and up
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/common/v4l2-tpg/v4l2-tpg-core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/media/common/v4l2-tpg/v4l2-tpg-core.c
+++ b/drivers/media/common/v4l2-tpg/v4l2-tpg-core.c
@@ -1738,7 +1738,7 @@ typedef struct { u16 __; u8 _; } __packe
unsigned s; \
\
for (s = 0; s < len; s++) { \
- u8 chr = font8x16[text[s] * 16 + line]; \
+ u8 chr = font8x16[(u8)text[s] * 16 + line]; \
\
if (hdiv == 2 && tpg->hflip) { \
pos[3] = (chr & (0x01 << 6) ? fg : bg); \
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomas Winkler <[email protected]>
commit 01f54664a4db0d612de0ece8e0022f21f9374e9b upstream.
First, rename out_no_locality to out_locality for bailing out on
both tpm_cmd_ready() and tpm_request_locality() failure.
Second, ignore the return value of go_to_idle() as it may override
the return value of the actual tpm operation, the go_to_idle() error
will be caught on any consequent command.
Last, fix the wrong 'goto out', that jumped back instead of forward.
Cc: [email protected]
Fixes: 627448e85c76 ("tpm: separate cmd_ready/go_idle from runtime_pm")
Signed-off-by: Tomas Winkler <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Tested-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/char/tpm/tpm-interface.c | 15 ++++++++-------
1 file changed, 8 insertions(+), 7 deletions(-)
--- a/drivers/char/tpm/tpm-interface.c
+++ b/drivers/char/tpm/tpm-interface.c
@@ -477,13 +477,15 @@ static ssize_t tpm_try_transmit(struct t
if (need_locality) {
rc = tpm_request_locality(chip, flags);
- if (rc < 0)
- goto out_no_locality;
+ if (rc < 0) {
+ need_locality = false;
+ goto out_locality;
+ }
}
rc = tpm_cmd_ready(chip, flags);
if (rc)
- goto out;
+ goto out_locality;
rc = tpm2_prepare_space(chip, space, ordinal, buf);
if (rc)
@@ -547,14 +549,13 @@ out_recv:
dev_err(&chip->dev, "tpm2_commit_space: error %d\n", rc);
out:
- rc = tpm_go_idle(chip, flags);
- if (rc)
- goto out;
+ /* may fail but do not override previous error value in rc */
+ tpm_go_idle(chip, flags);
+out_locality:
if (need_locality)
tpm_relinquish_locality(chip, flags);
-out_no_locality:
if (chip->ops->clk_enable != NULL)
chip->ops->clk_enable(chip, false);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hans Verkuil <[email protected]>
commit 62dcb4f41836bd3c44b5b651bb6df07ea4cb1551 upstream.
vb2_core_create_bufs did not check if the memory model for newly added
buffers is the same as for already existing buffers. It should return an
error if they aren't the same.
Signed-off-by: Hans Verkuil <[email protected]>
Reported-by: [email protected]
Cc: <[email protected]> # for v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/media/common/videobuf2/videobuf2-core.c | 3 +++
1 file changed, 3 insertions(+)
--- a/drivers/media/common/videobuf2/videobuf2-core.c
+++ b/drivers/media/common/videobuf2/videobuf2-core.c
@@ -800,6 +800,9 @@ int vb2_core_create_bufs(struct vb2_queu
memset(q->alloc_devs, 0, sizeof(q->alloc_devs));
q->memory = memory;
q->waiting_for_buffers = !q->is_output;
+ } else if (q->memory != memory) {
+ dprintk(1, "memory model mismatch\n");
+ return -EINVAL;
}
num_buffers = min(*count, VB2_MAX_FRAME - q->num_buffers);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Pan Bian <[email protected]>
commit 0ea295dd853e0879a9a30ab61f923c26be35b902 upstream.
The function truncate_node frees the page with f2fs_put_page. However,
the page index is read after that. So, the patch reads the index before
freeing the page.
Fixes: bf39c00a9a7f ("f2fs: drop obsolete node page when it is truncated")
Cc: <[email protected]>
Signed-off-by: Pan Bian <[email protected]>
Reviewed-by: Chao Yu <[email protected]>
Signed-off-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/f2fs/node.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
--- a/fs/f2fs/node.c
+++ b/fs/f2fs/node.c
@@ -827,6 +827,7 @@ static int truncate_node(struct dnode_of
struct f2fs_sb_info *sbi = F2FS_I_SB(dn->inode);
struct node_info ni;
int err;
+ pgoff_t index;
err = f2fs_get_node_info(sbi, dn->nid, &ni);
if (err)
@@ -846,10 +847,11 @@ static int truncate_node(struct dnode_of
clear_node_page_dirty(dn->node_page);
set_sbi_flag(sbi, SBI_IS_DIRTY);
+ index = dn->node_page->index;
f2fs_put_page(dn->node_page, 1);
invalidate_mapping_pages(NODE_MAPPING(sbi),
- dn->node_page->index, dn->node_page->index);
+ index, index);
dn->node_page = NULL;
trace_f2fs_truncate_node(dn->inode, dn->nid, ni.blk_addr);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit dc4501ff287547dea7ca10f1c580c741291a8760 ]
bearer_disable() already calls kfree_rcu() to free struct tipc_bearer,
we don't need to call kfree() again.
Fixes: cb30a63384bc ("tipc: refactor function tipc_enable_bearer()")
Reported-by: [email protected]
Cc: Ying Xue <[email protected]>
Cc: Jon Maloy <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/tipc/bearer.c | 1 -
1 file changed, 1 deletion(-)
--- a/net/tipc/bearer.c
+++ b/net/tipc/bearer.c
@@ -317,7 +317,6 @@ static int tipc_enable_bearer(struct net
res = tipc_disc_create(net, b, &b->bcast_addr, &skb);
if (res) {
bearer_disable(net, b);
- kfree(b);
errstr = "failed to create discoverer";
goto rejected;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <[email protected]>
[ Upstream commit 8203e2d844d34af247a151d8ebd68553a6e91785 ]
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: Sergey Matyukevich <[email protected]>
Tested-by: Sergey Matyukevich <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ipv4/ip_forward.c | 1 +
net/ipv6/ip6_output.c | 1 +
2 files changed, 2 insertions(+)
--- a/net/ipv4/ip_forward.c
+++ b/net/ipv4/ip_forward.c
@@ -72,6 +72,7 @@ static int ip_forward_finish(struct net
if (unlikely(opt->optlen))
ip_forward_options(skb);
+ skb->tstamp = 0;
return dst_output(net, sk, skb);
}
--- a/net/ipv6/ip6_output.c
+++ b/net/ipv6/ip6_output.c
@@ -378,6 +378,7 @@ static inline int ip6_forward_finish(str
__IP6_INC_STATS(net, ip6_dst_idev(dst), IPSTATS_MIB_OUTFORWDATAGRAMS);
__IP6_ADD_STATS(net, ip6_dst_idev(dst), IPSTATS_MIB_OUTOCTETS, skb->len);
+ skb->tstamp = 0;
return dst_output(net, sk, skb);
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit c433570458e49bccea5c551df628d058b3526289 ]
There are multiple issues here:
1. After freeing dev->ax25_ptr, we need to set it to NULL otherwise
we may use a dangling pointer.
2. There is a race between ax25_setsockopt() and device notifier as
reported by syzbot. Close it by holding RTNL lock.
3. We need to test if dev->ax25_ptr is NULL before using it.
Reported-and-tested-by: [email protected]
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/ax25/af_ax25.c | 11 +++++++++--
net/ax25/ax25_dev.c | 2 ++
2 files changed, 11 insertions(+), 2 deletions(-)
--- a/net/ax25/af_ax25.c
+++ b/net/ax25/af_ax25.c
@@ -653,15 +653,22 @@ static int ax25_setsockopt(struct socket
break;
}
- dev = dev_get_by_name(&init_net, devname);
+ rtnl_lock();
+ dev = __dev_get_by_name(&init_net, devname);
if (!dev) {
+ rtnl_unlock();
res = -ENODEV;
break;
}
ax25->ax25_dev = ax25_dev_ax25dev(dev);
+ if (!ax25->ax25_dev) {
+ rtnl_unlock();
+ res = -ENODEV;
+ break;
+ }
ax25_fillin_cb(ax25, ax25->ax25_dev);
- dev_put(dev);
+ rtnl_unlock();
break;
default:
--- a/net/ax25/ax25_dev.c
+++ b/net/ax25/ax25_dev.c
@@ -116,6 +116,7 @@ void ax25_dev_device_down(struct net_dev
if ((s = ax25_dev_list) == ax25_dev) {
ax25_dev_list = s->next;
spin_unlock_bh(&ax25_dev_lock);
+ dev->ax25_ptr = NULL;
dev_put(dev);
kfree(ax25_dev);
return;
@@ -125,6 +126,7 @@ void ax25_dev_device_down(struct net_dev
if (s->next == ax25_dev) {
s->next = ax25_dev->next;
spin_unlock_bh(&ax25_dev_lock);
+ dev->ax25_ptr = NULL;
dev_put(dev);
kfree(ax25_dev);
return;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Cong Wang <[email protected]>
[ Upstream commit 7314f5480f3e37e570104dc5e0f28823ef849e72 ]
nr_find_socket(), nr_find_peer() and nr_find_listener() lock the
sock after finding it in the global list. However, the call path
requires BH disabled for the sock lock consistently.
Actually the locking is unnecessary at this point, we can just hold
the sock refcnt to make sure it is not gone after we unlock the global
list, and lock it later only when needed.
Reported-and-tested-by: [email protected]
Signed-off-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/netrom/af_netrom.c | 15 ++++++++++-----
1 file changed, 10 insertions(+), 5 deletions(-)
--- a/net/netrom/af_netrom.c
+++ b/net/netrom/af_netrom.c
@@ -153,7 +153,7 @@ static struct sock *nr_find_listener(ax2
sk_for_each(s, &nr_list)
if (!ax25cmp(&nr_sk(s)->source_addr, addr) &&
s->sk_state == TCP_LISTEN) {
- bh_lock_sock(s);
+ sock_hold(s);
goto found;
}
s = NULL;
@@ -174,7 +174,7 @@ static struct sock *nr_find_socket(unsig
struct nr_sock *nr = nr_sk(s);
if (nr->my_index == index && nr->my_id == id) {
- bh_lock_sock(s);
+ sock_hold(s);
goto found;
}
}
@@ -198,7 +198,7 @@ static struct sock *nr_find_peer(unsigne
if (nr->your_index == index && nr->your_id == id &&
!ax25cmp(&nr->dest_addr, dest)) {
- bh_lock_sock(s);
+ sock_hold(s);
goto found;
}
}
@@ -224,7 +224,7 @@ static unsigned short nr_find_next_circu
if (i != 0 && j != 0) {
if ((sk=nr_find_socket(i, j)) == NULL)
break;
- bh_unlock_sock(sk);
+ sock_put(sk);
}
id++;
@@ -920,6 +920,7 @@ int nr_rx_frame(struct sk_buff *skb, str
}
if (sk != NULL) {
+ bh_lock_sock(sk);
skb_reset_transport_header(skb);
if (frametype == NR_CONNACK && skb->len == 22)
@@ -929,6 +930,7 @@ int nr_rx_frame(struct sk_buff *skb, str
ret = nr_process_rx_frame(sk, skb);
bh_unlock_sock(sk);
+ sock_put(sk);
return ret;
}
@@ -960,10 +962,12 @@ int nr_rx_frame(struct sk_buff *skb, str
(make = nr_make_new(sk)) == NULL) {
nr_transmit_refusal(skb, 0);
if (sk)
- bh_unlock_sock(sk);
+ sock_put(sk);
return 0;
}
+ bh_lock_sock(sk);
+
window = skb->data[20];
skb->sk = make;
@@ -1016,6 +1020,7 @@ int nr_rx_frame(struct sk_buff *skb, str
sk->sk_data_ready(sk);
bh_unlock_sock(sk);
+ sock_put(sk);
nr_insert_socket(make);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Myungho Jung <[email protected]>
[ Upstream commit 78abe3d0dfad196959b1246003366e2610775ea6 ]
clcsock can be released while kernel_accept() references it in TCP
listen worker. Also, clcsock needs to wake up before released if TCP
fallback is used and the clcsock is blocked by accept. Add a lock to
safely release clcsock and call kernel_sock_shutdown() to wake up
clcsock from accept in smc_release().
Reported-by: [email protected]
Reported-by: [email protected]
Signed-off-by: Myungho Jung <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/smc/af_smc.c | 14 ++++++++++++--
net/smc/smc.h | 4 ++++
2 files changed, 16 insertions(+), 2 deletions(-)
--- a/net/smc/af_smc.c
+++ b/net/smc/af_smc.c
@@ -145,8 +145,14 @@ static int smc_release(struct socket *so
sk->sk_shutdown |= SHUTDOWN_MASK;
}
if (smc->clcsock) {
+ if (smc->use_fallback && sk->sk_state == SMC_LISTEN) {
+ /* wake up clcsock accept */
+ rc = kernel_sock_shutdown(smc->clcsock, SHUT_RDWR);
+ }
+ mutex_lock(&smc->clcsock_release_lock);
sock_release(smc->clcsock);
smc->clcsock = NULL;
+ mutex_unlock(&smc->clcsock_release_lock);
}
if (smc->use_fallback) {
if (sk->sk_state != SMC_LISTEN && sk->sk_state != SMC_INIT)
@@ -203,6 +209,7 @@ static struct sock *smc_sock_alloc(struc
spin_lock_init(&smc->conn.send_lock);
sk->sk_prot->hash(sk);
sk_refcnt_debug_inc(sk);
+ mutex_init(&smc->clcsock_release_lock);
return sk;
}
@@ -818,7 +825,7 @@ static int smc_clcsock_accept(struct smc
struct socket *new_clcsock = NULL;
struct sock *lsk = &lsmc->sk;
struct sock *new_sk;
- int rc;
+ int rc = -EINVAL;
release_sock(lsk);
new_sk = smc_sock_alloc(sock_net(lsk), NULL, lsk->sk_protocol);
@@ -831,7 +838,10 @@ static int smc_clcsock_accept(struct smc
}
*new_smc = smc_sk(new_sk);
- rc = kernel_accept(lsmc->clcsock, &new_clcsock, 0);
+ mutex_lock(&lsmc->clcsock_release_lock);
+ if (lsmc->clcsock)
+ rc = kernel_accept(lsmc->clcsock, &new_clcsock, 0);
+ mutex_unlock(&lsmc->clcsock_release_lock);
lock_sock(lsk);
if (rc < 0)
lsk->sk_err = -rc;
--- a/net/smc/smc.h
+++ b/net/smc/smc.h
@@ -219,6 +219,10 @@ struct smc_sock { /* smc sock contain
* started, waiting for unsent
* data to be sent
*/
+ struct mutex clcsock_release_lock;
+ /* protects clcsock of a listen
+ * socket
+ * */
};
static inline struct smc_sock *smc_sk(const struct sock *sk)
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Yuval Avnery <[email protected]>
[ Upstream commit f0337889147c956721696553ffcc97212b0948fe ]
Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.
Fixes: bd5251dbf156 ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: Yuval Avnery <[email protected]>
Reviewed-by: Daniel Jurgens <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/fs_core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c
@@ -432,7 +432,7 @@ static void del_sw_hw_rule(struct fs_nod
if ((fte->action.action & MLX5_FLOW_CONTEXT_ACTION_FWD_DEST) &&
--fte->dests_size) {
- modify_mask = BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_DESTINATION_LIST),
+ modify_mask = BIT(MLX5_SET_FTE_MODIFY_ENABLE_MASK_DESTINATION_LIST);
update_fte = true;
}
out:
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Alaa Hleihel <[email protected]>
[ Upstream commit 4765420439e758bfa4808392d18b0a4cb6f06065 ]
mlx5 driver falsely advertises support of software timestamping.
Fix it by removing the false indication.
Fixes: ef9814deafd0 ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Alaa Hleihel <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Signed-off-by: Saeed Mahameed <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c | 11 +++--------
1 file changed, 3 insertions(+), 8 deletions(-)
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
@@ -1101,11 +1101,6 @@ int mlx5e_ethtool_get_ts_info(struct mlx
struct ethtool_ts_info *info)
{
struct mlx5_core_dev *mdev = priv->mdev;
- int ret;
-
- ret = ethtool_op_get_ts_info(priv->netdev, info);
- if (ret)
- return ret;
info->phc_index = mlx5_clock_get_ptp_index(mdev);
@@ -1113,9 +1108,9 @@ int mlx5e_ethtool_get_ts_info(struct mlx
info->phc_index == -1)
return 0;
- info->so_timestamping |= SOF_TIMESTAMPING_TX_HARDWARE |
- SOF_TIMESTAMPING_RX_HARDWARE |
- SOF_TIMESTAMPING_RAW_HARDWARE;
+ info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE |
+ SOF_TIMESTAMPING_RX_HARDWARE |
+ SOF_TIMESTAMPING_RAW_HARDWARE;
info->tx_types = BIT(HWTSTAMP_TX_OFF) |
BIT(HWTSTAMP_TX_ON);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jian-Hong Pan <[email protected]>
commit 82b01149ec94d746867d7f9156c44d775d4d2d67 upstream.
The headset mic of ASUS laptops like UX533FD, UX433FN and UX333FA, whose
CODEC is Realtek ALC294 has jack auto detection feature. This patch
enables the feature.
Fixes: 4e051106730d ("ALSA: hda/realtek: Enable audio jacks of ASUS UX533FD with ALC294")
Signed-off-by: Daniel Drake <[email protected]>
Signed-off-by: Jian-Hong Pan <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/hda/patch_realtek.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6424,7 +6424,7 @@ static const struct hda_fixup alc269_fix
[ALC294_FIXUP_ASUS_HEADSET_MIC] = {
.type = HDA_FIXUP_PINS,
.v.pins = (const struct hda_pintbl[]) {
- { 0x19, 0x01a1113c }, /* use as headset mic, without its own jack detect */
+ { 0x19, 0x01a1103c }, /* use as headset mic */
{ }
},
.chained = true,
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Scott Chen <[email protected]>
commit 8d503f206c336677954160ac62f0c7d9c219cd89 upstream.
Add device ids to pl2303 for the HP POS pole displays:
LM920: 03f0:026b
TD620: 03f0:0956
LD960TA: 03f0:4439
LD220TA: 03f0:4349
LM940: 03f0:5039
Signed-off-by: Scott Chen <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/usb/serial/pl2303.c | 5 +++++
drivers/usb/serial/pl2303.h | 5 +++++
2 files changed, 10 insertions(+)
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -91,9 +91,14 @@ static const struct usb_device_id id_tab
{ USB_DEVICE(YCCABLE_VENDOR_ID, YCCABLE_PRODUCT_ID) },
{ USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) },
{ USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) },
+ { USB_DEVICE(HP_VENDOR_ID, HP_LD220TA_PRODUCT_ID) },
{ USB_DEVICE(HP_VENDOR_ID, HP_LD960_PRODUCT_ID) },
+ { USB_DEVICE(HP_VENDOR_ID, HP_LD960TA_PRODUCT_ID) },
{ USB_DEVICE(HP_VENDOR_ID, HP_LCM220_PRODUCT_ID) },
{ USB_DEVICE(HP_VENDOR_ID, HP_LCM960_PRODUCT_ID) },
+ { USB_DEVICE(HP_VENDOR_ID, HP_LM920_PRODUCT_ID) },
+ { USB_DEVICE(HP_VENDOR_ID, HP_LM940_PRODUCT_ID) },
+ { USB_DEVICE(HP_VENDOR_ID, HP_TD620_PRODUCT_ID) },
{ USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) },
{ USB_DEVICE(ZEAGLE_VENDOR_ID, ZEAGLE_N2ITION3_PRODUCT_ID) },
{ USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) },
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -119,10 +119,15 @@
/* Hewlett-Packard POS Pole Displays */
#define HP_VENDOR_ID 0x03f0
+#define HP_LM920_PRODUCT_ID 0x026b
+#define HP_TD620_PRODUCT_ID 0x0956
#define HP_LD960_PRODUCT_ID 0x0b39
#define HP_LCM220_PRODUCT_ID 0x3139
#define HP_LCM960_PRODUCT_ID 0x3239
#define HP_LD220_PRODUCT_ID 0x3524
+#define HP_LD220TA_PRODUCT_ID 0x4349
+#define HP_LD960TA_PRODUCT_ID 0x4439
+#define HP_LM940_PRODUCT_ID 0x5039
/* Cressi Edy (diving computer) PC interface */
#define CRESSI_VENDOR_ID 0x04b8
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Takashi Sakamoto <[email protected]>
commit aa9a9e39b4f65733bf19d90cbd026e85a74efb99 upstream.
An initial commit to add tracepoints for packets without CIP headers
introduces a wrong assignment to 'data_blocks' value of
'out_packet_without_header' tracepoint.
This commit fixes the bug.
Cc: <[email protected]> # v4.12+
Fixes: b164d2fd6e49 ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/firewire/amdtp-stream-trace.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/sound/firewire/amdtp-stream-trace.h
+++ b/sound/firewire/amdtp-stream-trace.h
@@ -169,7 +169,7 @@ TRACE_EVENT(out_packet_without_header,
__entry->dest = fw_parent_device(s->unit)->node_id;
__entry->payload_quadlets = payload_length / 4;
__entry->data_blocks = data_blocks,
- __entry->data_blocks = s->data_block_counter,
+ __entry->data_block_counter = s->data_block_counter,
__entry->packet_index = s->packet_index;
__entry->irq = !!in_interrupt();
__entry->index = index;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Takashi Sakamoto <[email protected]>
commit 3d16200a3e55a39caa1c88419cb559c00316f721 upstream.
According to my memo at hand and saved records, writing 0x00000001 to
SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding
channel, however current implement uses reversed logic. This results in
muted volume in device side during playback.
This commit corrects the bug.
Cc: <[email protected]> # v4.12+
Fixes: 76fdb3a9e13a ('ALSA: fireface: add support for Fireface 400')
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/firewire/fireface/ff-protocol-ff400.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/sound/firewire/fireface/ff-protocol-ff400.c
+++ b/sound/firewire/fireface/ff-protocol-ff400.c
@@ -152,7 +152,7 @@ static int ff400_switch_fetching_mode(st
if (reg == NULL)
return -ENOMEM;
- if (enable) {
+ if (!enable) {
/*
* Each quadlet is corresponding to data channels in a data
* blocks in reverse order. Precisely, quadlets for available
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gustavo A. R. Silva <[email protected]>
commit 94ffb030b6d31ec840bb811be455dd2e26a4f43e upstream.
stream is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/pcm.c:140 snd_pcm_control_ioctl() warn: potential spectre issue 'pcm->streams' [r] (local cap)
Fix this by sanitizing stream before using it to index pcm->streams
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <[email protected]>
Cc: [email protected]
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/core/pcm.c | 2 ++
1 file changed, 2 insertions(+)
--- a/sound/core/pcm.c
+++ b/sound/core/pcm.c
@@ -25,6 +25,7 @@
#include <linux/time.h>
#include <linux/mutex.h>
#include <linux/device.h>
+#include <linux/nospec.h>
#include <sound/core.h>
#include <sound/minors.h>
#include <sound/pcm.h>
@@ -129,6 +130,7 @@ static int snd_pcm_control_ioctl(struct
return -EFAULT;
if (stream < 0 || stream > 1)
return -EINVAL;
+ stream = array_index_nospec(stream, 2);
if (get_user(subdevice, &info->subdevice))
return -EFAULT;
mutex_lock(®ister_mutex);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sameer Pujar <[email protected]>
commit 63d2a9ec310d8bcc955574220d4631aa55c1a80c upstream.
Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
Suggested-by: Mohan Kumar <[email protected]>
Suggested-by: Dara Ramesh <[email protected]>
Signed-off-by: Sameer Pujar <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
sound/pci/hda/hda_tegra.c | 2 ++
1 file changed, 2 insertions(+)
--- a/sound/pci/hda/hda_tegra.c
+++ b/sound/pci/hda/hda_tegra.c
@@ -249,10 +249,12 @@ static int hda_tegra_suspend(struct devi
struct snd_card *card = dev_get_drvdata(dev);
struct azx *chip = card->private_data;
struct hda_tegra *hda = container_of(chip, struct hda_tegra, chip);
+ struct hdac_bus *bus = azx_bus(chip);
snd_power_change_state(card, SNDRV_CTL_POWER_D3hot);
azx_stop_chip(chip);
+ synchronize_irq(bus->irq);
azx_enter_link_reset(chip);
hda_tegra_disable_clocks(hda);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sebastian Ott <[email protected]>
commit 98dfd32620e970eb576ebce5ea39d905cb005e72 upstream.
When triggered by pci hotplug (PEC 0x306) clp_get_state is called
with spinlocks held resulting in the following warning:
zpci: n/a: Event 0x306 reconfigured PCI function 0x0
BUG: sleeping function called from invalid context at mm/page_alloc.c:4324
in_atomic(): 1, irqs_disabled(): 0, pid: 98, name: kmcheck
2 locks held by kmcheck/98:
Change the allocation to use GFP_ATOMIC.
Cc: [email protected] # 4.13+
Signed-off-by: Sebastian Ott <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/s390/pci/pci_clp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/arch/s390/pci/pci_clp.c
+++ b/arch/s390/pci/pci_clp.c
@@ -436,7 +436,7 @@ int clp_get_state(u32 fid, enum zpci_sta
struct clp_state_data sd = {fid, ZPCI_FN_STATE_RESERVED};
int rc;
- rrb = clp_alloc_block(GFP_KERNEL);
+ rrb = clp_alloc_block(GFP_ATOMIC);
if (!rrb)
return -ENOMEM;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Willem de Bruijn <[email protected]>
[ Upstream commit 99137b7888f4058087895d035d81c6b2d31015c5 ]
Packet sockets with SOCK_DGRAM may pass an address for use in
dev_hard_header. Ensure that it is of sufficient length.
Reported-by: syzbot <[email protected]>
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
net/packet/af_packet.c | 4 ++++
1 file changed, 4 insertions(+)
--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -2627,6 +2627,8 @@ static int tpacket_snd(struct packet_soc
proto = saddr->sll_protocol;
addr = saddr->sll_addr;
dev = dev_get_by_index(sock_net(&po->sk), saddr->sll_ifindex);
+ if (addr && dev && saddr->sll_halen < dev->addr_len)
+ goto out;
}
err = -ENXIO;
@@ -2825,6 +2827,8 @@ static int packet_snd(struct socket *soc
proto = saddr->sll_protocol;
addr = saddr->sll_addr;
dev = dev_get_by_index(sock_net(sk), saddr->sll_ifindex);
+ if (addr && dev && saddr->sll_halen < dev->addr_len)
+ goto out;
}
err = -ENXIO;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lukas Wunner <[email protected]>
commit dbc944115eed48af110646992893dc43321368d8 upstream.
If submission of a DMA TX transfer succeeds but submission of the
corresponding RX transfer does not, the BCM2835 SPI driver terminates
the TX transfer but neglects to reset the dma_pending flag to false.
Thus, if the next transfer uses interrupt mode (because it is shorter
than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout,
dmaengine_terminate_all() will be called both for TX (once more) and
for RX (which was never started in the first place). Fix it.
Signed-off-by: Lukas Wunner <[email protected]>
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: [email protected] # v4.2+
Cc: Mathias Duckeck <[email protected]>
Cc: Frank Pavlic <[email protected]>
Cc: Martin Sperl <[email protected]>
Cc: Noralf Trønnes <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/spi/spi-bcm2835.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -341,6 +341,7 @@ static int bcm2835_spi_transfer_one_dma(
if (ret) {
/* need to reset on errors */
dmaengine_terminate_all(master->dma_tx);
+ bs->dma_pending = false;
bcm2835_spi_reset_hw(master);
return ret;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Johan Jonker <[email protected]>
commit 8b19faf6fae2867e2c177212c541e8ae36aa4d32 upstream.
Fix typo in common_clk_branches.
Make spdif_pre parent of spdif_frac.
Fixes: 667464208989 ("clk: rockchip: include downstream muxes into fractional dividers")
Cc: [email protected]
Signed-off-by: Johan Jonker <[email protected]>
Acked-by: Elaine Zhang <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/clk/rockchip/clk-rk3188.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/drivers/clk/rockchip/clk-rk3188.c
+++ b/drivers/clk/rockchip/clk-rk3188.c
@@ -382,7 +382,7 @@ static struct rockchip_clk_branch common
COMPOSITE_NOMUX(0, "spdif_pre", "i2s_src", 0,
RK2928_CLKSEL_CON(5), 0, 7, DFLAGS,
RK2928_CLKGATE_CON(0), 13, GFLAGS),
- COMPOSITE_FRACMUX(0, "spdif_frac", "spdif_pll", CLK_SET_RATE_PARENT,
+ COMPOSITE_FRACMUX(0, "spdif_frac", "spdif_pre", CLK_SET_RATE_PARENT,
RK2928_CLKSEL_CON(9), 0,
RK2928_CLKGATE_CON(0), 14, GFLAGS,
&common_spdif_fracmux),
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Anand Jain <[email protected]>
commit 0d228ece59a35a9b9e8ff0d40653234a6d90f61e upstream.
At the time of forced unmount we place the running replace to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state, so when the system comes
back and expect the target device is missing.
Then let the replace state continue to be in
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state instead of
BTRFS_IOCTL_DEV_REPLACE_STATE_STARTED as there isn't any matching scrub
running as part of replace.
Fixes: e93c89c1aaaa ("Btrfs: add new sources for device replace code")
CC: [email protected] # 4.4+
Signed-off-by: Anand Jain <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/dev-replace.c | 2 ++
1 file changed, 2 insertions(+)
--- a/fs/btrfs/dev-replace.c
+++ b/fs/btrfs/dev-replace.c
@@ -887,6 +887,8 @@ int btrfs_resume_dev_replace_async(struc
"cannot continue dev_replace, tgtdev is missing");
btrfs_info(fs_info,
"you may cancel the operation after 'mount -o degraded'");
+ dev_replace->replace_state =
+ BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED;
btrfs_dev_replace_write_unlock(dev_replace);
return 0;
}
On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
[ partial results; qemu tests incomplete ]
Build results:
total: 155 pass: 148 fail: 7
Failed builds:
arm:allmodconfig
mips:allmodconfig
parisc:allmodconfig
powerpc:ppc64e_defconfig
powerpc:cell_defconfig
powerpc:maple_defconfig
xtensa:allmodconfig
Qemu test results:
total: 332 pass: 331 fail: 1
Failed tests:
mipsel64:fuloong2e_defconfig:fulong2e:rootfs
Depending on the architecture, different variants of the same error.
ERROR: "__bad_cmpxchg" [drivers/spi/spi-bcm2835.ko] undefined!
ERROR: "__cmpxchg_small" [drivers/spi/spi-bcm2835.ko] undefined!
ERROR: "__cmpxchg_called_with_bad_pointer" [drivers/spi/spi-bcm2835.ko] undefined!
v4.4 and v4.20 are also affected by this problem. The impact differs
from release to release; for example, sparc64 is affected in v4.4.y,
but not in v4.19.y / v4.20.y. I suspect that the problem is also seen
in v4.9.y and v4.14.y, but the compilation doesn't get there
due to the other problems in those releases.
Also, for powerpc builds:
arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
and for mips64:
Building mipsel64:fuloong2e_defconfig:fulong2e:rootfs ... failed
------------
Error log:
In file included from ./arch/mips/include/asm/mmzone.h:10:0,
from ./arch/mips/include/asm/r4kcache.h:23,
from arch/mips/mm/c-r4k.c:33:
./arch/mips/include/asm/mach-loongson64/mmzone.h:48:0: error: "NODE_DATA" redefined [-Werror]
Guenter
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <[email protected]>
[ Upstream commit 202700e30740c6568b5a6943662f3829566dd533 ]
Using del_timer() + add_timer() is generally unsafe on SMP,
as noticed by syzbot. Use mod_timer() instead.
kernel BUG at kernel/time/timer.c:1136!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 1026 Comm: kworker/u4:4 Not tainted 4.20.0+ #2
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events_unbound flush_to_ldisc
RIP: 0010:add_timer kernel/time/timer.c:1136 [inline]
RIP: 0010:add_timer+0xa81/0x1470 kernel/time/timer.c:1134
Code: 4d 89 7d 40 48 c7 85 70 fe ff ff 00 00 00 00 c7 85 7c fe ff ff ff ff ff ff 48 89 85 90 fe ff ff e9 e6 f7 ff ff e8 cf 42 12 00 <0f> 0b e8 c8 42 12 00 0f 0b e8 c1 42 12 00 4c 89 bd 60 fe ff ff e9
RSP: 0018:ffff8880a7fdf5a8 EFLAGS: 00010293
RAX: ffff8880a7846340 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff816f3ee1 RDI: ffff88808a514ff8
RBP: ffff8880a7fdf760 R08: 0000000000000007 R09: ffff8880a7846c58
R10: ffff8880a7846340 R11: 0000000000000000 R12: ffff88808a514ff8
R13: ffff88808a514ff8 R14: ffff88808a514dc0 R15: 0000000000000030
FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000061c500 CR3: 00000000994d9000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
decode_prio_command drivers/net/hamradio/6pack.c:903 [inline]
sixpack_decode drivers/net/hamradio/6pack.c:971 [inline]
sixpack_receive_buf drivers/net/hamradio/6pack.c:457 [inline]
sixpack_receive_buf+0xf9c/0x1470 drivers/net/hamradio/6pack.c:434
tty_ldisc_receive_buf+0x164/0x1c0 drivers/tty/tty_buffer.c:465
tty_port_default_receive_buf+0x114/0x190 drivers/tty/tty_port.c:38
receive_buf drivers/tty/tty_buffer.c:481 [inline]
flush_to_ldisc+0x3b2/0x590 drivers/tty/tty_buffer.c:533
process_one_work+0xd0c/0x1ce0 kernel/workqueue.c:2153
worker_thread+0x143/0x14a0 kernel/workqueue.c:2296
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Cc: Andreas Koensgen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/net/hamradio/6pack.c | 16 ++++------------
1 file changed, 4 insertions(+), 12 deletions(-)
--- a/drivers/net/hamradio/6pack.c
+++ b/drivers/net/hamradio/6pack.c
@@ -524,10 +524,7 @@ static void resync_tnc(struct timer_list
/* Start resync timer again -- the TNC might be still absent */
-
- del_timer(&sp->resync_t);
- sp->resync_t.expires = jiffies + SIXP_RESYNC_TIMEOUT;
- add_timer(&sp->resync_t);
+ mod_timer(&sp->resync_t, jiffies + SIXP_RESYNC_TIMEOUT);
}
static inline int tnc_init(struct sixpack *sp)
@@ -538,9 +535,7 @@ static inline int tnc_init(struct sixpac
sp->tty->ops->write(sp->tty, &inbyte, 1);
- del_timer(&sp->resync_t);
- sp->resync_t.expires = jiffies + SIXP_RESYNC_TIMEOUT;
- add_timer(&sp->resync_t);
+ mod_timer(&sp->resync_t, jiffies + SIXP_RESYNC_TIMEOUT);
return 0;
}
@@ -918,11 +913,8 @@ static void decode_prio_command(struct s
/* if the state byte has been received, the TNC is present,
so the resync timer can be reset. */
- if (sp->tnc_state == TNC_IN_SYNC) {
- del_timer(&sp->resync_t);
- sp->resync_t.expires = jiffies + SIXP_INIT_RESYNC_TIMEOUT;
- add_timer(&sp->resync_t);
- }
+ if (sp->tnc_state == TNC_IN_SYNC)
+ mod_timer(&sp->resync_t, jiffies + SIXP_INIT_RESYNC_TIMEOUT);
sp->status1 = cmd & SIXP_PRIO_DATA_MASK;
}
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Patrick Dreyer <[email protected]>
commit 7db54c89f0b30a101584e09d3729144e6170059d upstream.
This adds ELAN0501 to the ACPI table to support Elan touchpad found in ASUS
Aspire F5-573G.
Signed-off-by: Patrick Dreyer <[email protected]>
Cc: [email protected]
Signed-off-by: Dmitry Torokhov <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/input/mouse/elan_i2c_core.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/input/mouse/elan_i2c_core.c
+++ b/drivers/input/mouse/elan_i2c_core.c
@@ -1336,6 +1336,7 @@ MODULE_DEVICE_TABLE(i2c, elan_id);
static const struct acpi_device_id elan_acpi_id[] = {
{ "ELAN0000", 0 },
{ "ELAN0100", 0 },
+ { "ELAN0501", 0 },
{ "ELAN0600", 0 },
{ "ELAN0602", 0 },
{ "ELAN0605", 0 },
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Nava kishore Manne <[email protected]>
commit 260683137ab5276113fc322fdbbc578024185fee upstream.
This patch Correct the RX interrupt mask value to handle the
RX interrupts properly.
Fixes: c8dbdc842d30 ("serial: xuartps: Rewrite the interrupt handling logic")
Signed-off-by: Nava kishore Manne <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/tty/serial/xilinx_uartps.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -125,7 +125,7 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout
#define CDNS_UART_IXR_RXTRIG 0x00000001 /* RX FIFO trigger interrupt */
#define CDNS_UART_IXR_RXFULL 0x00000004 /* RX FIFO full interrupt. */
#define CDNS_UART_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
-#define CDNS_UART_IXR_MASK 0x00001FFF /* Valid bit mask */
+#define CDNS_UART_IXR_RXMASK 0x000021e7 /* Valid RX bit mask */
/*
* Do not enable parity error interrupt for the following
@@ -362,7 +362,7 @@ static irqreturn_t cdns_uart_isr(int irq
cdns_uart_handle_tx(dev_id);
isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
}
- if (isrstatus & CDNS_UART_IXR_MASK)
+ if (isrstatus & CDNS_UART_IXR_RXMASK)
cdns_uart_handle_rx(dev_id, isrstatus);
spin_unlock(&port->lock);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Sylwester Nawrocki <[email protected]>
commit 8ac686d7dfed721102860ff2571e6b9f529ae81a upstream.
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
commit 647d04f8e07a ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f46 ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd1d ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
Cc: <[email protected]> # 4.17.x
Signed-off-by: Sylwester Nawrocki <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 9 ++++-----
arch/arm/boot/dts/exynos5422-odroidxu4.dts | 9 ++++-----
2 files changed, 8 insertions(+), 10 deletions(-)
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
@@ -26,8 +26,7 @@
"Speakers", "SPKL",
"Speakers", "SPKR";
- assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>,
- <&clock CLK_MOUT_EPLL>,
+ assigned-clocks = <&clock CLK_MOUT_EPLL>,
<&clock CLK_MOUT_MAU_EPLL>,
<&clock CLK_MOUT_USER_MAU_EPLL>,
<&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -36,8 +35,7 @@
<&clock_audss EXYNOS_DOUT_AUD_BUS>,
<&clock_audss EXYNOS_DOUT_I2S>;
- assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>,
- <&clock CLK_FOUT_EPLL>,
+ assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
<&clock CLK_MOUT_EPLL>,
<&clock CLK_MOUT_MAU_EPLL>,
<&clock CLK_MAU_EPLL>,
@@ -48,7 +46,6 @@
<0>,
<0>,
<0>,
- <0>,
<196608001>,
<(196608002 / 2)>,
<196608000>;
@@ -84,4 +81,6 @@
&i2s0 {
status = "okay";
+ assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>;
+ assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>;
};
--- a/arch/arm/boot/dts/exynos5422-odroidxu4.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidxu4.dts
@@ -33,8 +33,7 @@
compatible = "samsung,odroid-xu3-audio";
model = "Odroid-XU4";
- assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>,
- <&clock CLK_MOUT_EPLL>,
+ assigned-clocks = <&clock CLK_MOUT_EPLL>,
<&clock CLK_MOUT_MAU_EPLL>,
<&clock CLK_MOUT_USER_MAU_EPLL>,
<&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -43,8 +42,7 @@
<&clock_audss EXYNOS_DOUT_AUD_BUS>,
<&clock_audss EXYNOS_DOUT_I2S>;
- assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>,
- <&clock CLK_FOUT_EPLL>,
+ assigned-clock-parents = <&clock CLK_FOUT_EPLL>,
<&clock CLK_MOUT_EPLL>,
<&clock CLK_MOUT_MAU_EPLL>,
<&clock CLK_MAU_EPLL>,
@@ -55,7 +53,6 @@
<0>,
<0>,
<0>,
- <0>,
<196608001>,
<(196608002 / 2)>,
<196608000>;
@@ -79,6 +76,8 @@
&i2s0 {
status = "okay";
+ assigned-clocks = <&i2s0 CLK_I2S_RCLK_SRC>;
+ assigned-clock-parents = <&clock_audss EXYNOS_SCLK_I2S>;
};
&pwm {
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Tomas Winkler <[email protected]>
commit 2ba5780ce30549cf57929b01d8cba6fe656e31c5 upstream.
tpm_i2c_nuvoton calculated commands duration using TPM 1.x
values via tpm_calc_ordinal_duration() also for TPM 2.x chips.
Call tpm2_calc_ordinal_duration() for retrieving ordinal
duration for TPM 2.X chips.
Cc: [email protected]
Cc: Nayna Jain <[email protected]>
Signed-off-by: Tomas Winkler <[email protected]>
Reviewed-by: Nayna Jain <[email protected]>
Tested-by: Nayna Jain <[email protected]> (For TPM 2.0)
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
drivers/char/tpm/tpm_i2c_nuvoton.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
--- a/drivers/char/tpm/tpm_i2c_nuvoton.c
+++ b/drivers/char/tpm/tpm_i2c_nuvoton.c
@@ -369,6 +369,7 @@ static int i2c_nuvoton_send(struct tpm_c
struct device *dev = chip->dev.parent;
struct i2c_client *client = to_i2c_client(dev);
u32 ordinal;
+ unsigned long duration;
size_t count = 0;
int burst_count, bytes2write, retries, rc = -EIO;
@@ -455,10 +456,12 @@ static int i2c_nuvoton_send(struct tpm_c
return rc;
}
ordinal = be32_to_cpu(*((__be32 *) (buf + 6)));
- rc = i2c_nuvoton_wait_for_data_avail(chip,
- tpm_calc_ordinal_duration(chip,
- ordinal),
- &priv->read_queue);
+ if (chip->flags & TPM_CHIP_FLAG_TPM2)
+ duration = tpm2_calc_ordinal_duration(chip, ordinal);
+ else
+ duration = tpm_calc_ordinal_duration(chip, ordinal);
+
+ rc = i2c_nuvoton_wait_for_data_avail(chip, duration, &priv->read_queue);
if (rc) {
dev_err(dev, "%s() timeout command duration\n", __func__);
i2c_nuvoton_ready(chip);
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Dmitry Eremin-Solenikov <[email protected]>
commit fa4600734b74f74d9169c3015946d4722f8bcf79 upstream.
crypto_cfb_decrypt_segment() incorrectly XOR'ed generated keystream with
IV, rather than with data stream, resulting in incorrect decryption.
Test vectors will be added in the next patch.
Signed-off-by: Dmitry Eremin-Solenikov <[email protected]>
Cc: [email protected]
Signed-off-by: Herbert Xu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
crypto/cfb.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- a/crypto/cfb.c
+++ b/crypto/cfb.c
@@ -144,7 +144,7 @@ static int crypto_cfb_decrypt_segment(st
do {
crypto_cfb_encrypt_one(tfm, iv, dst);
- crypto_xor(dst, iv, bsize);
+ crypto_xor(dst, src, bsize);
iv = src;
src += bsize;
4.19-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lu Fengqi <[email protected]>
commit 27a7ff554e8d349627a90bda275c527b7348adae upstream.
The test case btrfs/001 with inode_cache mount option will encounter the
following warning:
WARNING: CPU: 1 PID: 23700 at fs/btrfs/inode.c:956 cow_file_range.isra.19+0x32b/0x430 [btrfs]
CPU: 1 PID: 23700 Comm: btrfs Kdump: loaded Tainted: G W O 4.20.0-rc4-custom+ #30
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:cow_file_range.isra.19+0x32b/0x430 [btrfs]
Call Trace:
? free_extent_buffer+0x46/0x90 [btrfs]
run_delalloc_nocow+0x455/0x900 [btrfs]
btrfs_run_delalloc_range+0x1a7/0x360 [btrfs]
writepage_delalloc+0xf9/0x150 [btrfs]
__extent_writepage+0x125/0x3e0 [btrfs]
extent_write_cache_pages+0x1b6/0x3e0 [btrfs]
? __wake_up_common_lock+0x63/0xc0
extent_writepages+0x50/0x80 [btrfs]
do_writepages+0x41/0xd0
? __filemap_fdatawrite_range+0x9e/0xf0
__filemap_fdatawrite_range+0xbe/0xf0
btrfs_fdatawrite_range+0x1b/0x50 [btrfs]
__btrfs_write_out_cache+0x42c/0x480 [btrfs]
btrfs_write_out_ino_cache+0x84/0xd0 [btrfs]
btrfs_save_ino_cache+0x551/0x660 [btrfs]
commit_fs_roots+0xc5/0x190 [btrfs]
btrfs_commit_transaction+0x2bf/0x8d0 [btrfs]
btrfs_mksubvol+0x48d/0x4d0 [btrfs]
btrfs_ioctl_snap_create_transid+0x170/0x180 [btrfs]
btrfs_ioctl_snap_create_v2+0x124/0x180 [btrfs]
btrfs_ioctl+0x123f/0x3030 [btrfs]
The file extent generation of the free space inode is equal to the last
snapshot of the file root, so the inode will be passed to cow_file_rage.
But the inode was created and its extents were preallocated in
btrfs_save_ino_cache, there are no cow copies on disk.
The preallocated extent is not yet in the extent tree, and
btrfs_cross_ref_exist will ignore the -ENOENT returned by
check_committed_ref, so we can directly write the inode to the disk.
Fixes: 78d4295b1eee ("btrfs: lift some btrfs_cross_ref_exist checks in nocow path")
CC: [email protected] # 4.18+
Reviewed-by: Filipe Manana <[email protected]>
Signed-off-by: Lu Fengqi <[email protected]>
Signed-off-by: David Sterba <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
fs/btrfs/inode.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -1373,7 +1373,8 @@ next_slot:
* Do the same check as in btrfs_cross_ref_exist but
* without the unnecessary search.
*/
- if (btrfs_file_extent_generation(leaf, fi) <=
+ if (!nolock &&
+ btrfs_file_extent_generation(leaf, fi) <=
btrfs_root_last_snapshot(&root->root_item))
goto out_check;
if (extent_type == BTRFS_FILE_EXTENT_REG && !force)
On 1/7/19 5:30 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.14-rc1.gz
> or in the git tree and branch at:
> git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>
Compiled and booted on my test system. No dmesg regressions.
thanks,
-- Shuah
On Mon, 7 Jan 2019 at 18:16, Greg Kroah-Hartman
<[email protected]> wrote:
>
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.14-rc1.gz
> or in the git tree and branch at:
> git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.19.y
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>
Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.
Summary
------------------------------------------------------------------------
kernel: 4.19.14-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.19.y
git commit: d7e734716c5ab8dbe6b25dc7200c54f9e82f54a6
git describe: v4.19.13-171-gd7e734716c5a
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-4.19-oe/build/v4.19.13-171-gd7e734716c5a
No regressions (compared to build v4.19.13)
No fixes (compared to build v4.19.13)
Ran 20546 total tests in the following environments and test suites.
Environments
--------------
- dragonboard-410c - arm64
- hi6220-hikey - arm64
- i386
- juno-r2 - arm64
- qemu_arm
- qemu_arm64
- qemu_i386
- qemu_x86_64
- x15 - arm
- x86_64
Test Suites
-----------
* boot
* install-android-platform-tools-r2600
* kselftest
* libhugetlbfs
* ltp-cap_bounds-tests
* ltp-containers-tests
* ltp-cpuhotplug-tests
* ltp-cve-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-timers-tests
* spectre-meltdown-checker-test
* ltp-open-posix-tests
* kselftest-vsyscall-mode-native
* kselftest-vsyscall-mode-none
--
Linaro LKFT
https://lkft.linaro.org
On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.14-rc1.gz
-rc2 is out to fix some build issues:
https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.19.14-rc2.gz
On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
Still (for v4.19.13-171-gc68ce175c3b8):
arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
Guenter
On Tue, Jan 08, 2019 at 09:25:03AM -0800, Guenter Roeck wrote:
> On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.19.14 release.
> > There are 170 patches in this series, all will be posted as a response
> > to this one. If anyone has any issues with these being applied, please
> > let me know.
> >
> > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > Anything received after that time might be too late.
> >
>
> Still (for v4.19.13-171-gc68ce175c3b8):
>
> arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
> arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
>
> AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
Breno on this thread just said that this patch should not be applied,
and another one will be submitted upstream instead to solve the problem
correctly and then we can backport it.
So we can live with this build issue for now.
thanks,
greg k-h
On Tue, Jan 08, 2019 at 06:56:40PM +0100, Greg Kroah-Hartman wrote:
> On Tue, Jan 08, 2019 at 09:25:03AM -0800, Guenter Roeck wrote:
> > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > This is the start of the stable review cycle for the 4.19.14 release.
> > > There are 170 patches in this series, all will be posted as a response
> > > to this one. If anyone has any issues with these being applied, please
> > > let me know.
> > >
> > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > Anything received after that time might be too late.
> > >
> >
> > Still (for v4.19.13-171-gc68ce175c3b8):
> >
> > arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
> > arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
> >
> > AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
>
> Breno on this thread just said that this patch should not be applied,
> and another one will be submitted upstream instead to solve the problem
> correctly and then we can backport it.
>
> So we can live with this build issue for now.
>
I think you should drop the offending patch in this case. It doesn't make
sense to keep it - all it accomplishes is to break various builds. What is
the point of doing that ? Is that somehow better than living with the bug
it is supposed to fix ?
Guenter
On Tue, Jan 08, 2019 at 10:09:51AM -0800, Guenter Roeck wrote:
> On Tue, Jan 08, 2019 at 06:56:40PM +0100, Greg Kroah-Hartman wrote:
> > On Tue, Jan 08, 2019 at 09:25:03AM -0800, Guenter Roeck wrote:
> > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > There are 170 patches in this series, all will be posted as a response
> > > > to this one. If anyone has any issues with these being applied, please
> > > > let me know.
> > > >
> > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > Anything received after that time might be too late.
> > > >
> > >
> > > Still (for v4.19.13-171-gc68ce175c3b8):
> > >
> > > arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
> > > arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
> > >
> > > AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
> >
> > Breno on this thread just said that this patch should not be applied,
> > and another one will be submitted upstream instead to solve the problem
> > correctly and then we can backport it.
> >
> > So we can live with this build issue for now.
> >
>
> I think you should drop the offending patch in this case. It doesn't make
> sense to keep it - all it accomplishes is to break various builds. What is
> the point of doing that ? Is that somehow better than living with the bug
> it is supposed to fix ?
That's what the developers involved seem to say.
Breno, should I drop the offending patch now, or wait for your fix to
land and then fix up the build then?
thanks,
greg k-h
On Tue, Jan 08, 2019 at 07:13:22PM +0100, Greg Kroah-Hartman wrote:
> On Tue, Jan 08, 2019 at 10:09:51AM -0800, Guenter Roeck wrote:
> > On Tue, Jan 08, 2019 at 06:56:40PM +0100, Greg Kroah-Hartman wrote:
> > > On Tue, Jan 08, 2019 at 09:25:03AM -0800, Guenter Roeck wrote:
> > > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > > There are 170 patches in this series, all will be posted as a response
> > > > > to this one. If anyone has any issues with these being applied, please
> > > > > let me know.
> > > > >
> > > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > > Anything received after that time might be too late.
> > > > >
> > > >
> > > > Still (for v4.19.13-171-gc68ce175c3b8):
> > > >
> > > > arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
> > > > arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
> > > >
> > > > AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
> > >
> > > Breno on this thread just said that this patch should not be applied,
> > > and another one will be submitted upstream instead to solve the problem
> > > correctly and then we can backport it.
> > >
> > > So we can live with this build issue for now.
> > >
> >
> > I think you should drop the offending patch in this case. It doesn't make
> > sense to keep it - all it accomplishes is to break various builds. What is
> > the point of doing that ? Is that somehow better than living with the bug
> > it is supposed to fix ?
>
> That's what the developers involved seem to say.
>
That will prevent anyone affected from actually using 4.19.14, and earlier
kernels will still have the problem people are now so concerned about.
In other words, this will accomplish exactly nothig except confirm the
notion that stable releases are not well tested. I _really_ don't get
the point, sorry.
Guenter
On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.19.14 release.
> There are 170 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> Anything received after that time might be too late.
>
For v4.19.13-171-gc68ce175c3b8:
Build results:
total: 155 pass: 152 fail: 3
Failed builds:
powerpc:ppc64e_defconfig
powerpc:cell_defconfig
powerpc:maple_defconfig
Qemu test results:
total: 332 pass: 319 fail: 13
Failed tests:
ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
Failure as reported.
arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
Guenter
On Tue, Jan 08, 2019 at 10:29:38AM -0800, Guenter Roeck wrote:
> On Tue, Jan 08, 2019 at 07:13:22PM +0100, Greg Kroah-Hartman wrote:
> > On Tue, Jan 08, 2019 at 10:09:51AM -0800, Guenter Roeck wrote:
> > > On Tue, Jan 08, 2019 at 06:56:40PM +0100, Greg Kroah-Hartman wrote:
> > > > On Tue, Jan 08, 2019 at 09:25:03AM -0800, Guenter Roeck wrote:
> > > > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > > > There are 170 patches in this series, all will be posted as a response
> > > > > > to this one. If anyone has any issues with these being applied, please
> > > > > > let me know.
> > > > > >
> > > > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > > > Anything received after that time might be too late.
> > > > > >
> > > > >
> > > > > Still (for v4.19.13-171-gc68ce175c3b8):
> > > > >
> > > > > arch/powerpc/kernel/signal_64.c: In function ‘sys_rt_sigreturn’:
> > > > > arch/powerpc/kernel/signal_64.c:761:21: error: ‘msr’ undeclared
> > > > >
> > > > > AFAICS commit 5c784c8414fba ("powerpc/tm: Remove msr_tm_active()") is missing.
> > > >
> > > > Breno on this thread just said that this patch should not be applied,
> > > > and another one will be submitted upstream instead to solve the problem
> > > > correctly and then we can backport it.
> > > >
> > > > So we can live with this build issue for now.
> > > >
> > >
> > > I think you should drop the offending patch in this case. It doesn't make
> > > sense to keep it - all it accomplishes is to break various builds. What is
> > > the point of doing that ? Is that somehow better than living with the bug
> > > it is supposed to fix ?
> >
> > That's what the developers involved seem to say.
> >
> That will prevent anyone affected from actually using 4.19.14, and earlier
> kernels will still have the problem people are now so concerned about.
> In other words, this will accomplish exactly nothig except confirm the
> notion that stable releases are not well tested. I _really_ don't get
> the point, sorry.
No, you are right, we shouldn't include stuff we know is broken for a
large group. I've dropped the patch now from everywhere.
thanks,
greg k-h
On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
> On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.19.14 release.
> > There are 170 patches in this series, all will be posted as a response
> > to this one. If anyone has any issues with these being applied, please
> > let me know.
> >
> > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > Anything received after that time might be too late.
> >
>
> For v4.19.13-171-gc68ce175c3b8:
>
> Build results:
> total: 155 pass: 152 fail: 3
> Failed builds:
> powerpc:ppc64e_defconfig
> powerpc:cell_defconfig
> powerpc:maple_defconfig
> Qemu test results:
> total: 332 pass: 319 fail: 13
> Failed tests:
> ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
> ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
> ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
> ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
> ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
> ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
> ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
> ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
> ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
> ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
> ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
> ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
> ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
Ugh, I thought this was just the cell build, didn't realize it hit more.
Ok, I've dropped the patch from all queues. Odd that it only causes
problems on 4.19.y :(
thanks,
greg k-h
On Wed, Jan 09, 2019 at 03:38:11PM +0100, Greg Kroah-Hartman wrote:
> On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
> > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > This is the start of the stable review cycle for the 4.19.14 release.
> > > There are 170 patches in this series, all will be posted as a response
> > > to this one. If anyone has any issues with these being applied, please
> > > let me know.
> > >
> > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > Anything received after that time might be too late.
> > >
> >
> > For v4.19.13-171-gc68ce175c3b8:
> >
> > Build results:
> > total: 155 pass: 152 fail: 3
> > Failed builds:
> > powerpc:ppc64e_defconfig
> > powerpc:cell_defconfig
> > powerpc:maple_defconfig
> > Qemu test results:
> > total: 332 pass: 319 fail: 13
> > Failed tests:
> > ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
> > ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
> > ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
> > ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
> > ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
> > ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
> > ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
> > ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
> > ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
> > ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
> > ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
> > ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
> > ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
>
> Ugh, I thought this was just the cell build, didn't realize it hit more.
>
> Ok, I've dropped the patch from all queues. Odd that it only causes
> problems on 4.19.y :(
>
I don't know what you dropped, but v4.19.14 fails to build with
the same error. Did you drop it after the release ?
Guenter
On Wed, Jan 09, 2019 at 11:40:48AM -0800, Guenter Roeck wrote:
> On Wed, Jan 09, 2019 at 03:38:11PM +0100, Greg Kroah-Hartman wrote:
> > On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
> > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > There are 170 patches in this series, all will be posted as a response
> > > > to this one. If anyone has any issues with these being applied, please
> > > > let me know.
> > > >
> > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > Anything received after that time might be too late.
> > > >
> > >
> > > For v4.19.13-171-gc68ce175c3b8:
> > >
> > > Build results:
> > > total: 155 pass: 152 fail: 3
> > > Failed builds:
> > > powerpc:ppc64e_defconfig
> > > powerpc:cell_defconfig
> > > powerpc:maple_defconfig
> > > Qemu test results:
> > > total: 332 pass: 319 fail: 13
> > > Failed tests:
> > > ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
> > > ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
> > > ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
> > > ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
> > > ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
> > > ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
> > > ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
> > > ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
> > > ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
> > > ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
> > > ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
> > > ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
> > > ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
> >
> > Ugh, I thought this was just the cell build, didn't realize it hit more.
> >
> > Ok, I've dropped the patch from all queues. Odd that it only causes
> > problems on 4.19.y :(
> >
> I don't know what you dropped, but v4.19.14 fails to build with
> the same error. Did you drop it after the release ?
No, I should have dropped it before the release. Let me go see what I
messed up...
On Thu, Jan 10, 2019 at 07:52:07AM +0100, Greg Kroah-Hartman wrote:
> On Wed, Jan 09, 2019 at 11:40:48AM -0800, Guenter Roeck wrote:
> > On Wed, Jan 09, 2019 at 03:38:11PM +0100, Greg Kroah-Hartman wrote:
> > > On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
> > > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > > There are 170 patches in this series, all will be posted as a response
> > > > > to this one. If anyone has any issues with these being applied, please
> > > > > let me know.
> > > > >
> > > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > > Anything received after that time might be too late.
> > > > >
> > > >
> > > > For v4.19.13-171-gc68ce175c3b8:
> > > >
> > > > Build results:
> > > > total: 155 pass: 152 fail: 3
> > > > Failed builds:
> > > > powerpc:ppc64e_defconfig
> > > > powerpc:cell_defconfig
> > > > powerpc:maple_defconfig
> > > > Qemu test results:
> > > > total: 332 pass: 319 fail: 13
> > > > Failed tests:
> > > > ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
> > > > ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
> > > > ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
> > > > ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
> > > > ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
> > > > ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
> > > > ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
> > > > ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
> > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
> > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
> > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
> > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
> > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
> > >
> > > Ugh, I thought this was just the cell build, didn't realize it hit more.
> > >
> > > Ok, I've dropped the patch from all queues. Odd that it only causes
> > > problems on 4.19.y :(
> > >
> > I don't know what you dropped, but v4.19.14 fails to build with
> > the same error. Did you drop it after the release ?
>
> No, I should have dropped it before the release. Let me go see what I
> messed up...
I dropped e1c3743e1a20 ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
from the stable trees, which is what I was told was the commit that was
causing the problems by Christoph and Breno (on to: now).
Was that not the offending commit? If so, what one was?
totally confused,
greg k-h
On 1/10/19 5:17 AM, Greg Kroah-Hartman wrote:
> On Thu, Jan 10, 2019 at 07:52:07AM +0100, Greg Kroah-Hartman wrote:
>> On Wed, Jan 09, 2019 at 11:40:48AM -0800, Guenter Roeck wrote:
>>> On Wed, Jan 09, 2019 at 03:38:11PM +0100, Greg Kroah-Hartman wrote:
>>>> On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
>>>>> On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
>>>>>> This is the start of the stable review cycle for the 4.19.14 release.
>>>>>> There are 170 patches in this series, all will be posted as a response
>>>>>> to this one. If anyone has any issues with these being applied, please
>>>>>> let me know.
>>>>>>
>>>>>> Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
>>>>>> Anything received after that time might be too late.
>>>>>>
>>>>>
>>>>> For v4.19.13-171-gc68ce175c3b8:
>>>>>
>>>>> Build results:
>>>>> total: 155 pass: 152 fail: 3
>>>>> Failed builds:
>>>>> powerpc:ppc64e_defconfig
>>>>> powerpc:cell_defconfig
>>>>> powerpc:maple_defconfig
>>>>> Qemu test results:
>>>>> total: 332 pass: 319 fail: 13
>>>>> Failed tests:
>>>>> ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
>>>>> ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
>>>>> ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
>>>>> ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
>>>>> ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
>>>>> ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
>>>>> ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
>>>>> ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
>>>>> ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
>>>>> ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
>>>>> ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
>>>>> ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
>>>>> ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
>>>>
>>>> Ugh, I thought this was just the cell build, didn't realize it hit more.
>>>>
>>>> Ok, I've dropped the patch from all queues. Odd that it only causes
>>>> problems on 4.19.y :(
>>>>
>>> I don't know what you dropped, but v4.19.14 fails to build with
>>> the same error. Did you drop it after the release ?
>>
>> No, I should have dropped it before the release. Let me go see what I
>> messed up...
>
> I dropped e1c3743e1a20 ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
> from the stable trees, which is what I was told was the commit that was
> causing the problems by Christoph and Breno (on to: now).
>
> Was that not the offending commit? If so, what one was?
>
$ git describe
v4.19.14
groeck@server:~/src/linux-stable$ git log --oneline v4.19.13.. arch/powerpc/
a9935a127688 powerpc/tm: Unset MSR[TS] if not recheckpointing
34fc09193486 powerpc/fsl: Fix spectre_v2 mitigations reporting
groeck@server:~/src/linux-stable$
a9935a127688 is the culprit.
Guenter
Greg Kroah-Hartman wrote...
> I dropped e1c3743e1a20 ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
> from the stable trees, which is what I was told was the commit that was
> causing the problems by Christoph and Breno (on to: now).
>
> Was that not the offending commit? If so, what one was?
>
> totally confused,
Sorry for not getting back to you earlier. Building yesterday's
release (v4.19.14) *failed*, bisect led to
| commit a9935a12768851762089fda8e5a9daaf0231808e (HEAD)
| Author: Breno Leitao <[email protected]>
| Date: Mon Nov 26 18:12:00 2018 -0200
|
| powerpc/tm: Unset MSR[TS] if not recheckpointing
Reverting that commit seems to be sufficient, build passes then.
Additionally, neither 4.20 nor 5.0-rc1 show this problem. The
| commit 6f5b9f018f4c7686fd944d920209d1382d320e4e upstream.
builds as well, so I'll try to find the missing prerequisite next.
An example .config is attached.
Christoph
Christoph Biedl wrote...
> Sorry for not getting back to you earlier. Building yesterday's
> release (v4.19.14) *failed*, bisect led to
>
> | commit a9935a12768851762089fda8e5a9daaf0231808e (HEAD)
> | Author: Breno Leitao <[email protected]>
> | Date: Mon Nov 26 18:12:00 2018 -0200
> |
> | powerpc/tm: Unset MSR[TS] if not recheckpointing
>
> Reverting that commit seems to be sufficient, build passes then.
>
> Additionally, neither 4.20 nor 5.0-rc1 show this problem. The
> | commit 6f5b9f018f4c7686fd944d920209d1382d320e4e upstream.
> builds as well, so I'll try to find the missing prerequisite next.
Cherry-picking
| commit 5c784c8414fba11b62e12439f11e109fb5751f38
| Author: Breno Leitao <[email protected]>
| Date: Thu Aug 16 14:21:07 2018 -0300
|
| powerpc/tm: Remove msr_tm_active()
makes the build pass. Bruno, does this make sense?
Christoph
On Thu, Jan 10, 2019 at 04:15:40PM +0100, Christoph Biedl wrote:
> Christoph Biedl wrote...
>
> > Sorry for not getting back to you earlier. Building yesterday's
> > release (v4.19.14) *failed*, bisect led to
> >
> > | commit a9935a12768851762089fda8e5a9daaf0231808e (HEAD)
> > | Author: Breno Leitao <[email protected]>
> > | Date: Mon Nov 26 18:12:00 2018 -0200
> > |
> > | powerpc/tm: Unset MSR[TS] if not recheckpointing
> >
> > Reverting that commit seems to be sufficient, build passes then.
> >
> > Additionally, neither 4.20 nor 5.0-rc1 show this problem. The
> > | commit 6f5b9f018f4c7686fd944d920209d1382d320e4e upstream.
> > builds as well, so I'll try to find the missing prerequisite next.
>
> Cherry-picking
>
> | commit 5c784c8414fba11b62e12439f11e109fb5751f38
> | Author: Breno Leitao <[email protected]>
> | Date: Thu Aug 16 14:21:07 2018 -0300
> |
> | powerpc/tm: Remove msr_tm_active()
>
> makes the build pass. Bruno, does this make sense?
>
As I had reported and suggested well before the release.
According to Greg those responsible for the patch series rejected that.
Guenter
On Thu, Jan 10, 2019 at 07:40:39AM -0800, Guenter Roeck wrote:
> On Thu, Jan 10, 2019 at 04:15:40PM +0100, Christoph Biedl wrote:
> > Christoph Biedl wrote...
> >
> > > Sorry for not getting back to you earlier. Building yesterday's
> > > release (v4.19.14) *failed*, bisect led to
> > >
> > > | commit a9935a12768851762089fda8e5a9daaf0231808e (HEAD)
> > > | Author: Breno Leitao <[email protected]>
> > > | Date: Mon Nov 26 18:12:00 2018 -0200
> > > |
> > > | powerpc/tm: Unset MSR[TS] if not recheckpointing
> > >
> > > Reverting that commit seems to be sufficient, build passes then.
> > >
> > > Additionally, neither 4.20 nor 5.0-rc1 show this problem. The
> > > | commit 6f5b9f018f4c7686fd944d920209d1382d320e4e upstream.
> > > builds as well, so I'll try to find the missing prerequisite next.
> >
> > Cherry-picking
> >
> > | commit 5c784c8414fba11b62e12439f11e109fb5751f38
> > | Author: Breno Leitao <[email protected]>
> > | Date: Thu Aug 16 14:21:07 2018 -0300
> > |
> > | powerpc/tm: Remove msr_tm_active()
> >
> > makes the build pass. Bruno, does this make sense?
> >
> As I had reported and suggested well before the release.
> According to Greg those responsible for the patch series rejected that.
Ok, Breno and Christoph, what should I do here? Should I drop this
patch in the tree or add this new one? Ideally I can fix this soon as I
don't like having broken trees out there...
thanks,
greg k-h
Greg Kroah-Hartman wrote...
> Ok, Breno and Christoph, what should I do here? Should I drop this
> patch in the tree or add this new one? Ideally I can fix this soon as I
> don't like having broken trees out there...
Whatever Breno says - I don't feel competent enough to decide what's
right here.
Christoph
On Thu, Jan 10, 2019 at 11:55:45PM +0100, Christoph Biedl wrote:
> Greg Kroah-Hartman wrote...
>
> > Ok, Breno and Christoph, what should I do here? Should I drop this
> > patch in the tree or add this new one? Ideally I can fix this soon as I
> > don't like having broken trees out there...
>
> Whatever Breno says - I don't feel competent enough to decide what's
> right here.
Ok, I'm reverting it and adding back the patch that I accidentally
dropped thinking it was the broken one.
thanks,
greg k-h
On Thu, Jan 10, 2019 at 06:27:33AM -0800, Guenter Roeck wrote:
> On 1/10/19 5:17 AM, Greg Kroah-Hartman wrote:
> > On Thu, Jan 10, 2019 at 07:52:07AM +0100, Greg Kroah-Hartman wrote:
> > > On Wed, Jan 09, 2019 at 11:40:48AM -0800, Guenter Roeck wrote:
> > > > On Wed, Jan 09, 2019 at 03:38:11PM +0100, Greg Kroah-Hartman wrote:
> > > > > On Tue, Jan 08, 2019 at 03:07:31PM -0800, Guenter Roeck wrote:
> > > > > > On Mon, Jan 07, 2019 at 01:30:27PM +0100, Greg Kroah-Hartman wrote:
> > > > > > > This is the start of the stable review cycle for the 4.19.14 release.
> > > > > > > There are 170 patches in this series, all will be posted as a response
> > > > > > > to this one. If anyone has any issues with these being applied, please
> > > > > > > let me know.
> > > > > > >
> > > > > > > Responses should be made by Wed Jan 9 10:43:54 UTC 2019.
> > > > > > > Anything received after that time might be too late.
> > > > > > >
> > > > > >
> > > > > > For v4.19.13-171-gc68ce175c3b8:
> > > > > >
> > > > > > Build results:
> > > > > > total: 155 pass: 152 fail: 3
> > > > > > Failed builds:
> > > > > > powerpc:ppc64e_defconfig
> > > > > > powerpc:cell_defconfig
> > > > > > powerpc:maple_defconfig
> > > > > > Qemu test results:
> > > > > > total: 332 pass: 319 fail: 13
> > > > > > Failed tests:
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:nosmp:initrd
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:smp:initrd
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:smp:ide:rootfs
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:smp:mmc:rootfs
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:smp:nvme:rootfs
> > > > > > ppc64:mac99:ppc64_book3s_defconfig:smp:scsi[DC395]:rootfs
> > > > > > ppc64:mpc8544ds:ppc64_e5500_defconfig:nosmp:initrd
> > > > > > ppc64:mpc8544ds:ppc64_e5500_defconfig:smp:initrd
> > > > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:initrd
> > > > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:nvme:rootfs
> > > > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:mmc:rootfs
> > > > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:scsi[53C895A]:rootfs
> > > > > > ppc64:ppce500:corenet64_smp_defconfig:e5500:sata-sii3112:rootfs
> > > > >
> > > > > Ugh, I thought this was just the cell build, didn't realize it hit more.
> > > > >
> > > > > Ok, I've dropped the patch from all queues. Odd that it only causes
> > > > > problems on 4.19.y :(
> > > > >
> > > > I don't know what you dropped, but v4.19.14 fails to build with
> > > > the same error. Did you drop it after the release ?
> > >
> > > No, I should have dropped it before the release. Let me go see what I
> > > messed up...
> >
> > I dropped e1c3743e1a20 ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
> > from the stable trees, which is what I was told was the commit that was
> > causing the problems by Christoph and Breno (on to: now).
> >
> > Was that not the offending commit? If so, what one was?
> >
> $ git describe
> v4.19.14
> groeck@server:~/src/linux-stable$ git log --oneline v4.19.13.. arch/powerpc/
> a9935a127688 powerpc/tm: Unset MSR[TS] if not recheckpointing
> 34fc09193486 powerpc/fsl: Fix spectre_v2 mitigations reporting
> groeck@server:~/src/linux-stable$
>
> a9935a127688 is the culprit.
Thanks for this, now reverted.
greg k-h