From: Kiran Gunda <[email protected]>
Add PM6150/PM6150L peripherals such as PON, GPIOs, ADC and other
PMIC infra modules.
Signed-off-by: Kiran Gunda <[email protected]>
Signed-off-by: Rajendra Nayak <[email protected]>
---
arch/arm64/boot/dts/qcom/pm6150.dtsi | 85 +++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/pm6150l.dtsi | 47 ++++++++++++++
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 2 +
3 files changed, 134 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm6150.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/pm6150l.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
new file mode 100644
index 000000000000..20eb928e5ce3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/thermal/thermal.h>
+
+&spmi_bus {
+ pm6150_lsid0: pmic@0 {
+ compatible = "qcom,pm6150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm6150_pon: pon@800 {
+ compatible = "qcom,pm8998-pon";
+ reg = <0x800>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+ };
+ };
+
+ pm6150_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm6150_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ adc-chan@ADC5_DIE_TEMP {
+ reg = <ADC5_DIE_TEMP>;
+ label = "die_temp";
+ };
+ };
+
+ pm6150_gpio: gpios@c000 {
+ compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000 0xa00>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
+ <0 0xc1 0 IRQ_TYPE_NONE>,
+ <0 0xc2 0 IRQ_TYPE_NONE>,
+ <0 0xc3 0 IRQ_TYPE_NONE>,
+ <0 0xc4 0 IRQ_TYPE_NONE>,
+ <0 0xc5 0 IRQ_TYPE_NONE>,
+ <0 0xc6 0 IRQ_TYPE_NONE>,
+ <0 0xc7 0 IRQ_TYPE_NONE>,
+ <0 0xc8 0 IRQ_TYPE_NONE>,
+ <0 0xc9 0 IRQ_TYPE_NONE>;
+
+ interrupt-names = "pm6150_gpio1", "pm6150_gpio2",
+ "pm6150_gpio3", "pm6150_gpio4",
+ "pm6150_gpio5", "pm6150_gpio6",
+ "pm6150_gpio7", "pm6150_gpio8",
+ "pm6150_gpio9", "pm6150_gpio10";
+ };
+ };
+
+ pm6150_lsid1: pmic@1 {
+ compatible = "qcom,pm6150", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
new file mode 100644
index 000000000000..b17bb1af9367
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pm6150l_lsid4: pmic@4 {
+ compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm6150l_gpios: gpios@c000 {
+ compatible = "qcom,pm6150l-gpio", "qcom,spmi-gpio";
+ reg = <0xc000 0xc00>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <4 0xc0 0 IRQ_TYPE_NONE>,
+ <4 0xc1 0 IRQ_TYPE_NONE>,
+ <4 0xc2 0 IRQ_TYPE_NONE>,
+ <4 0xc3 0 IRQ_TYPE_NONE>,
+ <4 0xc4 0 IRQ_TYPE_NONE>,
+ <4 0xc5 0 IRQ_TYPE_NONE>,
+ <4 0xc6 0 IRQ_TYPE_NONE>,
+ <4 0xc7 0 IRQ_TYPE_NONE>,
+ <4 0xc8 0 IRQ_TYPE_NONE>,
+ <4 0xc9 0 IRQ_TYPE_NONE>,
+ <4 0xca 0 IRQ_TYPE_NONE>,
+ <4 0xcb 0 IRQ_TYPE_NONE>;
+
+ interrupt-names = "pm6150l_gpio1", "pm6150l_gpio2",
+ "pm6150l_gpio3", "pm6150l_gpio4",
+ "pm6150l_gpio5", "pm6150l_gpio6",
+ "pm6150l_gpio7", "pm6150l_gpio8",
+ "pm6150l_gpio9", "pm6150l_gpio10",
+ "pm6150l_gpio11", "pm6150l_gpio12";
+ };
+ };
+
+ pm6150l_lsid5: pmic@5 {
+ compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 5ee6eb3e2b99..be42ae9d2d9d 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -8,6 +8,8 @@
/dts-v1/;
#include "sc7180.dtsi"
+#include "pm6150.dtsi"
+#include "pm6150l.dtsi"
/ {
model = "Qualcomm Technologies, Inc. SC7180 IDP";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Quoting Rajendra Nayak (2019-10-23 02:02:16)
> diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> new file mode 100644
> index 000000000000..20eb928e5ce3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> @@ -0,0 +1,85 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +// Copyright (c) 2019, The Linux Foundation. All rights reserved.
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +&spmi_bus {
> + pm6150_lsid0: pmic@0 {
> + compatible = "qcom,pm6150", "qcom,spmi-pmic";
> + reg = <0x0 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm6150_pon: pon@800 {
> + compatible = "qcom,pm8998-pon";
> + reg = <0x800>;
> + mode-bootloader = <0x2>;
> + mode-recovery = <0x1>;
Can this have status = "disabled"? Or is the idea that if the pmic power
button isn't used it should be disabled in the board dts file?
> +
> + pwrkey {
> + compatible = "qcom,pm8941-pwrkey";
> + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_POWER>;
> + };
> + };
> +
> + pm6150_temp: temp-alarm@2400 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0x2400>;
> + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
> + io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
> + io-channel-names = "thermal";
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm6150_adc: adc@3100 {
> + compatible = "qcom,spmi-adc5";
> + reg = <0x3100>;
> + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> +
> + adc-chan@ADC5_DIE_TEMP {
> + reg = <ADC5_DIE_TEMP>;
> + label = "die_temp";
> + };
> + };
> +
> + pm6150_gpio: gpios@c000 {
> + compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
> + reg = <0xc000 0xa00>;
Drop the size?
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
> + <0 0xc1 0 IRQ_TYPE_NONE>,
> + <0 0xc2 0 IRQ_TYPE_NONE>,
> + <0 0xc3 0 IRQ_TYPE_NONE>,
> + <0 0xc4 0 IRQ_TYPE_NONE>,
> + <0 0xc5 0 IRQ_TYPE_NONE>,
> + <0 0xc6 0 IRQ_TYPE_NONE>,
> + <0 0xc7 0 IRQ_TYPE_NONE>,
> + <0 0xc8 0 IRQ_TYPE_NONE>,
> + <0 0xc9 0 IRQ_TYPE_NONE>;
Isn't this supposed to go away?
> +
> + interrupt-names = "pm6150_gpio1", "pm6150_gpio2",
> + "pm6150_gpio3", "pm6150_gpio4",
> + "pm6150_gpio5", "pm6150_gpio6",
> + "pm6150_gpio7", "pm6150_gpio8",
> + "pm6150_gpio9", "pm6150_gpio10";
And this? And have gpio-ranges and use the irqdomain work. Basically,
should look like pm8998.
> + };
> + };
> +
> + pm6150_lsid1: pmic@1 {
> + compatible = "qcom,pm6150", "qcom,spmi-pmic";
> + reg = <0x1 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +};
On 2019-10-29 22:08, Stephen Boyd wrote:
> Quoting Rajendra Nayak (2019-10-23 02:02:16)
>> diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi
>> b/arch/arm64/boot/dts/qcom/pm6150.dtsi
>> new file mode 100644
>> index 000000000000..20eb928e5ce3
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
>> @@ -0,0 +1,85 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +// Copyright (c) 2019, The Linux Foundation. All rights reserved.
>> +
>> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
>> +#include <dt-bindings/input/linux-event-codes.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/spmi/spmi.h>
>> +#include <dt-bindings/thermal/thermal.h>
>> +
>> +&spmi_bus {
>> + pm6150_lsid0: pmic@0 {
>> + compatible = "qcom,pm6150", "qcom,spmi-pmic";
>> + reg = <0x0 SPMI_USID>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + pm6150_pon: pon@800 {
>> + compatible = "qcom,pm8998-pon";
>> + reg = <0x800>;
>> + mode-bootloader = <0x2>;
>> + mode-recovery = <0x1>;
>
> Can this have status = "disabled"? Or is the idea that if the pmic
> power
> button isn't used it should be disabled in the board dts file?
>
Yes. The idea is to go with latter option. Disable it in the board dts
file if the
pmic power button is not used.
>> +
>> + pwrkey {
>> + compatible = "qcom,pm8941-pwrkey";
>> + interrupts = <0x0 0x8 0
>> IRQ_TYPE_EDGE_BOTH>;
>> + debounce = <15625>;
>> + bias-pull-up;
>> + linux,code = <KEY_POWER>;
>> + };
>> + };
>> +
>> + pm6150_temp: temp-alarm@2400 {
>> + compatible = "qcom,spmi-temp-alarm";
>> + reg = <0x2400>;
>> + interrupts = <0x0 0x24 0x0
>> IRQ_TYPE_EDGE_RISING>;
>> + io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
>> + io-channel-names = "thermal";
>> + #thermal-sensor-cells = <0>;
>> + };
>> +
>> + pm6150_adc: adc@3100 {
>> + compatible = "qcom,spmi-adc5";
>> + reg = <0x3100>;
>> + interrupts = <0x0 0x31 0x0
>> IRQ_TYPE_EDGE_RISING>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #io-channel-cells = <1>;
>> +
>> + adc-chan@ADC5_DIE_TEMP {
>> + reg = <ADC5_DIE_TEMP>;
>> + label = "die_temp";
>> + };
>> + };
>> +
>> + pm6150_gpio: gpios@c000 {
>> + compatible = "qcom,pm6150-gpio",
>> "qcom,spmi-gpio";
>> + reg = <0xc000 0xa00>;
>
> Drop the size?
>
Will drop it in next series.
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
>> + <0 0xc1 0 IRQ_TYPE_NONE>,
>> + <0 0xc2 0 IRQ_TYPE_NONE>,
>> + <0 0xc3 0 IRQ_TYPE_NONE>,
>> + <0 0xc4 0 IRQ_TYPE_NONE>,
>> + <0 0xc5 0 IRQ_TYPE_NONE>,
>> + <0 0xc6 0 IRQ_TYPE_NONE>,
>> + <0 0xc7 0 IRQ_TYPE_NONE>,
>> + <0 0xc8 0 IRQ_TYPE_NONE>,
>> + <0 0xc9 0 IRQ_TYPE_NONE>;
>
> Isn't this supposed to go away?
>
Yes. We can remove them if we want to go with the way done for pm8998.
>> +
>> + interrupt-names = "pm6150_gpio1",
>> "pm6150_gpio2",
>> + "pm6150_gpio3",
>> "pm6150_gpio4",
>> + "pm6150_gpio5",
>> "pm6150_gpio6",
>> + "pm6150_gpio7",
>> "pm6150_gpio8",
>> + "pm6150_gpio9",
>> "pm6150_gpio10";
>
> And this? And have gpio-ranges and use the irqdomain work. Basically,
> should look like pm8998.
Ok.. We can go ahead with the pm8998 way as well. We will address it in
next series.
>
>> + };
>> + };
>> +
>> + pm6150_lsid1: pmic@1 {
>> + compatible = "qcom,pm6150", "qcom,spmi-pmic";
>> + reg = <0x1 SPMI_USID>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +};
Quoting [email protected] (2019-10-30 00:06:05)
> On 2019-10-29 22:08, Stephen Boyd wrote:
> > Quoting Rajendra Nayak (2019-10-23 02:02:16)
> >> diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi
> >> b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> >> new file mode 100644
> >> index 000000000000..20eb928e5ce3
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> >> @@ -0,0 +1,85 @@
> >> +// SPDX-License-Identifier: BSD-3-Clause
> >> +// Copyright (c) 2019, The Linux Foundation. All rights reserved.
> >> +
> >> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> >> +#include <dt-bindings/input/linux-event-codes.h>
> >> +#include <dt-bindings/interrupt-controller/irq.h>
> >> +#include <dt-bindings/spmi/spmi.h>
> >> +#include <dt-bindings/thermal/thermal.h>
> >> +
> >> +&spmi_bus {
> >> + pm6150_lsid0: pmic@0 {
> >> + compatible = "qcom,pm6150", "qcom,spmi-pmic";
> >> + reg = <0x0 SPMI_USID>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + pm6150_pon: pon@800 {
> >> + compatible = "qcom,pm8998-pon";
> >> + reg = <0x800>;
> >> + mode-bootloader = <0x2>;
> >> + mode-recovery = <0x1>;
> >
> > Can this have status = "disabled"? Or is the idea that if the pmic
> > power
> > button isn't used it should be disabled in the board dts file?
> >
> Yes. The idea is to go with latter option. Disable it in the board dts
> file if the
> pmic power button is not used.
Ok. Thanks.
> >> +
> >> + interrupt-names = "pm6150_gpio1",
> >> "pm6150_gpio2",
> >> + "pm6150_gpio3",
> >> "pm6150_gpio4",
> >> + "pm6150_gpio5",
> >> "pm6150_gpio6",
> >> + "pm6150_gpio7",
> >> "pm6150_gpio8",
> >> + "pm6150_gpio9",
> >> "pm6150_gpio10";
> >
> > And this? And have gpio-ranges and use the irqdomain work. Basically,
> > should look like pm8998.
> Ok.. We can go ahead with the pm8998 way as well. We will address it in
> next series.
Yes please use the pm8998 way..