Hi,
There have been reports in the past of libata core code size
being a problem in migration from deprecated IDE subsystem on
legacy PATA only systems, i.e.:
https://lore.kernel.org/linux-ide/[email protected]/
This patchset re-organizes libata core code to exclude SATA
specific code from being built for PATA only setups.
The end result is up to 24% (by 23949 bytes, from 101769 bytes to
77820 bytes) smaller libata core code size (as measured for m68k
arch using modified atari_defconfig) on affected setups.
I've tested this patchset using pata_falcon driver under ARAnyM
emulator.
patches #1-11 are general fixes/cleanups done in the process of
making the patchset (there should be no inter-dependencies between
them except patch #10 which depends on patch #9)
patch #12 separates PATA timings code to libata-pata-timings.c file
patches #13-15 let compiler optimize out SATA specific code on
non-SATA hosts by adding !IS_ENABLED(CONFIG_SATA_HOST) instances
patches #16-22 separate SATA only code from libata-core.c file to
libata-sata.c one
patches #23-24 separate SATA only code from libata-scsi.c file to
libata-sata.c one
patches #25-26 separate SATA only code from libata-eh.c file to
libata-sata.c one
patch #27 makes "libata.force" kernel parameter optional
Changes since v2
(https://lore.kernel.org/linux-ide/[email protected]/):
- rebased on top of next-20200227
- added "ata: optimize ata_scsi_rbuf[] size" patch
Changes since v1
(https://lore.kernel.org/linux-ide/[email protected]/):
- added Acked-by: tag from Tejun to "ata: remove stale maintainership
information from core code" patch
- added Reviewed-by: tag from Martin to "ata: make SATA_PMP option
selectable only if any SATA host driver is enabled" patch
- added Reviewed-by: tag from Christoph to following patches:
- "ata: simplify ata_scsiop_inq_89()"
- "ata: use COMMAND_LINE_SIZE for ata_force_param_buf[] size"
- "ata: optimize struct ata_force_param size"
- "ata: move EXPORT_SYMBOL_GPL()s close to exported code"
- "ata: remove EXPORT_SYMBOL_GPL()s not used by modules"
- converted "ata: add CONFIG_SATA_HOST=n version of ata_ncq_enabled()"
patch to use IS_ENABLED()
- added "ata: let compiler optimize out ata_dev_config_ncq() on
non-SATA hosts" and "ata: let compiler optimize out ata_eh_set_lpm()
on non-SATA hosts" patches
- moved "ata: move sata_scr_*() to libata-core-sata.c" patch just
after "ata: start separating SATA specific code from libata-core.c"
one
- dropped no longer needed patches (code savings <= 8 bytes):
- "ata: move ata_do_link_spd_horkage() to libata-core-sata.c"
- "ata: move ata_dev_config_ncq*() to libata-core-sata.c"
- "ata: move sata_print_link_status() to libata-core-sata.c"
- "ata: move sata_down_spd_limit() to libata-core-sata.c"
- "ata: move sata_link_init_spd() to libata-core-sata.c"
- "ata: move ata_eh_set_lpm() to libata-core-sata.c"
- removed superfluos ifdefs
- dropped file names in top of file headers
- merged libata-scsi-sata.c and libata-eh-sata.c into libata-sata.c
- emphasised in patch descriptions that atari_defconfig used for
measurements has been modified (original one is still using
deprecated IDE subsystem)
- added "ata: make "libata.force" kernel parameter optional" patch
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
Bartlomiej Zolnierkiewicz (27):
ata: remove stale maintainership information from core code
ata: expose ncq_enable_prio sysfs attribute only on NCQ capable hosts
ata: make SATA_PMP option selectable only if any SATA host driver is
enabled
sata_promise: use ata_cable_sata()
ata: simplify ata_scsiop_inq_89()
ata: use COMMAND_LINE_SIZE for ata_force_param_buf[] size
ata: optimize struct ata_force_param size
ata: optimize ata_scsi_rbuf[] size
ata: move EXPORT_SYMBOL_GPL()s close to exported code
ata: remove EXPORT_SYMBOL_GPL()s not used by modules
ata: fix CodingStyle issues in PATA timings code
ata: separate PATA timings code from libata-core.c
ata: add CONFIG_SATA_HOST=n version of ata_ncq_enabled()
ata: let compiler optimize out ata_dev_config_ncq() on non-SATA hosts
ata: let compiler optimize out ata_eh_set_lpm() on non-SATA hosts
ata: start separating SATA specific code from libata-core.c
ata: move sata_scr_*() to libata-sata.c
ata: move *sata_set_spd*() to libata-sata.c
ata: move sata_link_{debounce,resume}() to libata-sata.c
ata: move sata_link_hardreset() to libata-sata.c
ata: move ata_qc_complete_multiple() to libata-sata.c
ata: move sata_deb_timing_*() to libata-sata.c
ata: start separating SATA specific code from libata-scsi.c
ata: move ata_sas_*() to libata-sata.c
ata: start separating SATA specific code from libata-eh.c
ata: move ata_eh_analyze_ncq_error() & co. to libata-sata.c
ata: make "libata.force" kernel parameter optional
drivers/ata/Kconfig | 77 ++
drivers/ata/Makefile | 2 +
drivers/ata/libata-core.c | 1126 ++--------------------
drivers/ata/libata-eh.c | 224 +----
drivers/ata/libata-pata-timings.c | 192 ++++
drivers/ata/libata-sata.c | 1483 +++++++++++++++++++++++++++++
drivers/ata/libata-scsi.c | 544 +----------
drivers/ata/libata-sff.c | 4 -
drivers/ata/libata.h | 25 +-
drivers/ata/sata_promise.c | 8 +-
drivers/scsi/Kconfig | 1 +
drivers/scsi/libsas/Kconfig | 1 +
include/linux/libata.h | 163 ++--
13 files changed, 2009 insertions(+), 1841 deletions(-)
create mode 100644 drivers/ata/libata-pata-timings.c
create mode 100644 drivers/ata/libata-sata.c
--
2.24.1
Use core helper instead of open-coding it.
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/sata_promise.c | 8 +-------
1 file changed, 1 insertion(+), 7 deletions(-)
diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c
index c451d7d1c817..8729f78cef5f 100644
--- a/drivers/ata/sata_promise.c
+++ b/drivers/ata/sata_promise.c
@@ -157,7 +157,6 @@ static int pdc_sata_hardreset(struct ata_link *link, unsigned int *class,
static void pdc_error_handler(struct ata_port *ap);
static void pdc_post_internal_cmd(struct ata_queued_cmd *qc);
static int pdc_pata_cable_detect(struct ata_port *ap);
-static int pdc_sata_cable_detect(struct ata_port *ap);
static struct scsi_host_template pdc_ata_sht = {
ATA_BASE_SHT(DRV_NAME),
@@ -183,7 +182,7 @@ static const struct ata_port_operations pdc_common_ops = {
static struct ata_port_operations pdc_sata_ops = {
.inherits = &pdc_common_ops,
- .cable_detect = pdc_sata_cable_detect,
+ .cable_detect = ata_cable_sata,
.freeze = pdc_sata_freeze,
.thaw = pdc_sata_thaw,
.scr_read = pdc_sata_scr_read,
@@ -459,11 +458,6 @@ static int pdc_pata_cable_detect(struct ata_port *ap)
return ATA_CBL_PATA80;
}
-static int pdc_sata_cable_detect(struct ata_port *ap)
-{
- return ATA_CBL_SATA;
-}
-
static int pdc_sata_scr_read(struct ata_link *link,
unsigned int sc_reg, u32 *val)
{
--
2.24.1
* move sata_link_{debounce,resume}() to libata-sata.c
* add static inline for CONFIG_SATA_HOST=n case (only one,
for sata_link_resume() is needed)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
32816 572 40 33428 8294 drivers/ata/libata-core.o
after:
32724 572 40 33336 8238 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 138 --------------------------------------
drivers/ata/libata-sata.c | 138 ++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 14 ++--
3 files changed, 148 insertions(+), 142 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 13214ebd0e5c..4ca81ef7c8bd 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3485,144 +3485,6 @@ int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
}
EXPORT_SYMBOL_GPL(ata_wait_after_reset);
-/**
- * sata_link_debounce - debounce SATA phy status
- * @link: ATA link to debounce SATA phy status for
- * @params: timing parameters { interval, duration, timeout } in msec
- * @deadline: deadline jiffies for the operation
- *
- * Make sure SStatus of @link reaches stable state, determined by
- * holding the same value where DET is not 1 for @duration polled
- * every @interval, before @timeout. Timeout constraints the
- * beginning of the stable state. Because DET gets stuck at 1 on
- * some controllers after hot unplugging, this functions waits
- * until timeout then returns 0 if DET is stable at 1.
- *
- * @timeout is further limited by @deadline. The sooner of the
- * two is used.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno on failure.
- */
-int sata_link_debounce(struct ata_link *link, const unsigned long *params,
- unsigned long deadline)
-{
- unsigned long interval = params[0];
- unsigned long duration = params[1];
- unsigned long last_jiffies, t;
- u32 last, cur;
- int rc;
-
- t = ata_deadline(jiffies, params[2]);
- if (time_before(t, deadline))
- deadline = t;
-
- if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
- return rc;
- cur &= 0xf;
-
- last = cur;
- last_jiffies = jiffies;
-
- while (1) {
- ata_msleep(link->ap, interval);
- if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
- return rc;
- cur &= 0xf;
-
- /* DET stable? */
- if (cur == last) {
- if (cur == 1 && time_before(jiffies, deadline))
- continue;
- if (time_after(jiffies,
- ata_deadline(last_jiffies, duration)))
- return 0;
- continue;
- }
-
- /* unstable, start over */
- last = cur;
- last_jiffies = jiffies;
-
- /* Check deadline. If debouncing failed, return
- * -EPIPE to tell upper layer to lower link speed.
- */
- if (time_after(jiffies, deadline))
- return -EPIPE;
- }
-}
-EXPORT_SYMBOL_GPL(sata_link_debounce);
-
-/**
- * sata_link_resume - resume SATA link
- * @link: ATA link to resume SATA
- * @params: timing parameters { interval, duration, timeout } in msec
- * @deadline: deadline jiffies for the operation
- *
- * Resume SATA phy @link and debounce it.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno on failure.
- */
-int sata_link_resume(struct ata_link *link, const unsigned long *params,
- unsigned long deadline)
-{
- int tries = ATA_LINK_RESUME_TRIES;
- u32 scontrol, serror;
- int rc;
-
- if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
- return rc;
-
- /*
- * Writes to SControl sometimes get ignored under certain
- * controllers (ata_piix SIDPR). Make sure DET actually is
- * cleared.
- */
- do {
- scontrol = (scontrol & 0x0f0) | 0x300;
- if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
- return rc;
- /*
- * Some PHYs react badly if SStatus is pounded
- * immediately after resuming. Delay 200ms before
- * debouncing.
- */
- if (!(link->flags & ATA_LFLAG_NO_DB_DELAY))
- ata_msleep(link->ap, 200);
-
- /* is SControl restored correctly? */
- if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
- return rc;
- } while ((scontrol & 0xf0f) != 0x300 && --tries);
-
- if ((scontrol & 0xf0f) != 0x300) {
- ata_link_warn(link, "failed to resume link (SControl %X)\n",
- scontrol);
- return 0;
- }
-
- if (tries < ATA_LINK_RESUME_TRIES)
- ata_link_warn(link, "link resume succeeded after %d retries\n",
- ATA_LINK_RESUME_TRIES - tries);
-
- if ((rc = sata_link_debounce(link, params, deadline)))
- return rc;
-
- /* clear SError, some PHYs require this even for SRST to work */
- if (!(rc = sata_scr_read(link, SCR_ERROR, &serror)))
- rc = sata_scr_write(link, SCR_ERROR, serror);
-
- return rc != -EINVAL ? rc : 0;
-}
-EXPORT_SYMBOL_GPL(sata_link_resume);
-
/**
* ata_std_prereset - prepare for reset
* @link: ATA link to be reset
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index d66afdc33d54..34852fced999 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -196,6 +196,144 @@ void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf)
}
EXPORT_SYMBOL_GPL(ata_tf_from_fis);
+/**
+ * sata_link_debounce - debounce SATA phy status
+ * @link: ATA link to debounce SATA phy status for
+ * @params: timing parameters { interval, duration, timeout } in msec
+ * @deadline: deadline jiffies for the operation
+ *
+ * Make sure SStatus of @link reaches stable state, determined by
+ * holding the same value where DET is not 1 for @duration polled
+ * every @interval, before @timeout. Timeout constraints the
+ * beginning of the stable state. Because DET gets stuck at 1 on
+ * some controllers after hot unplugging, this functions waits
+ * until timeout then returns 0 if DET is stable at 1.
+ *
+ * @timeout is further limited by @deadline. The sooner of the
+ * two is used.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
+ */
+int sata_link_debounce(struct ata_link *link, const unsigned long *params,
+ unsigned long deadline)
+{
+ unsigned long interval = params[0];
+ unsigned long duration = params[1];
+ unsigned long last_jiffies, t;
+ u32 last, cur;
+ int rc;
+
+ t = ata_deadline(jiffies, params[2]);
+ if (time_before(t, deadline))
+ deadline = t;
+
+ if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
+ return rc;
+ cur &= 0xf;
+
+ last = cur;
+ last_jiffies = jiffies;
+
+ while (1) {
+ ata_msleep(link->ap, interval);
+ if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
+ return rc;
+ cur &= 0xf;
+
+ /* DET stable? */
+ if (cur == last) {
+ if (cur == 1 && time_before(jiffies, deadline))
+ continue;
+ if (time_after(jiffies,
+ ata_deadline(last_jiffies, duration)))
+ return 0;
+ continue;
+ }
+
+ /* unstable, start over */
+ last = cur;
+ last_jiffies = jiffies;
+
+ /* Check deadline. If debouncing failed, return
+ * -EPIPE to tell upper layer to lower link speed.
+ */
+ if (time_after(jiffies, deadline))
+ return -EPIPE;
+ }
+}
+EXPORT_SYMBOL_GPL(sata_link_debounce);
+
+/**
+ * sata_link_resume - resume SATA link
+ * @link: ATA link to resume SATA
+ * @params: timing parameters { interval, duration, timeout } in msec
+ * @deadline: deadline jiffies for the operation
+ *
+ * Resume SATA phy @link and debounce it.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
+ */
+int sata_link_resume(struct ata_link *link, const unsigned long *params,
+ unsigned long deadline)
+{
+ int tries = ATA_LINK_RESUME_TRIES;
+ u32 scontrol, serror;
+ int rc;
+
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ return rc;
+
+ /*
+ * Writes to SControl sometimes get ignored under certain
+ * controllers (ata_piix SIDPR). Make sure DET actually is
+ * cleared.
+ */
+ do {
+ scontrol = (scontrol & 0x0f0) | 0x300;
+ if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
+ return rc;
+ /*
+ * Some PHYs react badly if SStatus is pounded
+ * immediately after resuming. Delay 200ms before
+ * debouncing.
+ */
+ if (!(link->flags & ATA_LFLAG_NO_DB_DELAY))
+ ata_msleep(link->ap, 200);
+
+ /* is SControl restored correctly? */
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ return rc;
+ } while ((scontrol & 0xf0f) != 0x300 && --tries);
+
+ if ((scontrol & 0xf0f) != 0x300) {
+ ata_link_warn(link, "failed to resume link (SControl %X)\n",
+ scontrol);
+ return 0;
+ }
+
+ if (tries < ATA_LINK_RESUME_TRIES)
+ ata_link_warn(link, "link resume succeeded after %d retries\n",
+ ATA_LINK_RESUME_TRIES - tries);
+
+ if ((rc = sata_link_debounce(link, params, deadline)))
+ return rc;
+
+ /* clear SError, some PHYs require this even for SRST to work */
+ if (!(rc = sata_scr_read(link, SCR_ERROR, &serror)))
+ rc = sata_scr_write(link, SCR_ERROR, serror);
+
+ return rc != -EINVAL ? rc : 0;
+}
+EXPORT_SYMBOL_GPL(sata_link_resume);
+
/**
* sata_link_scr_lpm - manipulate SControl IPM and SPM fields
* @link: ATA link to manipulate SControl for
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 3f0bdc2c30d3..3981e413f582 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1079,10 +1079,6 @@ static inline int ata_port_is_dummy(struct ata_port *ap)
extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
extern int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
-extern int sata_link_debounce(struct ata_link *link,
- const unsigned long *params, unsigned long deadline);
-extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
- unsigned long deadline);
extern int sata_link_hardreset(struct ata_link *link,
const unsigned long *timing, unsigned long deadline,
bool *online, int (*check_ready)(struct ata_link *));
@@ -1196,6 +1192,8 @@ extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
extern int sata_set_spd(struct ata_link *link);
+extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
+ unsigned long deadline);
#else
static inline int sata_scr_valid(struct ata_link *link) { return 0; }
static inline int sata_scr_read(struct ata_link *link, int reg, u32 *val)
@@ -1211,7 +1209,15 @@ static inline int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
return -EOPNOTSUPP;
}
static inline int sata_set_spd(struct ata_link *link) { return -EOPNOTSUPP; }
+static inline int sata_link_resume(struct ata_link *link,
+ const unsigned long *params,
+ unsigned long deadline)
+{
+ return -EOPNOTSUPP;
+}
#endif
+extern int sata_link_debounce(struct ata_link *link,
+ const unsigned long *params, unsigned long deadline);
extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
bool spm_wakeup);
extern int ata_slave_link_init(struct ata_port *ap);
--
2.24.1
Start separating SATA specific code from libata-scsi.c:
* un-static ata_scsi_find_dev()
* move following code to libata-sata.c:
- SATA only sysfs device attributes handling
- __ata_change_queue_depth()
- ata_scsi_change_queue_depth()
* cover with CONFIG_SATA_HOST ifdef SATA only sysfs device
attributes handling code and ATA_SHT_NCQ() macro in
<linux/libata.h>
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
20702 105 576 21383 5387 drivers/ata/libata-scsi.o
after:
19137 23 576 19736 4d18 drivers/ata/libata-scsi.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-sata.c | 298 +++++++++++++++++++++++++++++++++++++
drivers/ata/libata-scsi.c | 301 +-------------------------------------
drivers/ata/libata.h | 2 +
include/linux/libata.h | 9 +-
4 files changed, 308 insertions(+), 302 deletions(-)
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index f3ad4aca5d09..341699f5af20 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -8,6 +8,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <scsi/scsi_device.h>
#include <linux/libata.h>
#include "libata.h"
@@ -764,3 +765,300 @@ bool sata_lpm_ignore_phy_events(struct ata_link *link)
return false;
}
EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
+
+static const char *ata_lpm_policy_names[] = {
+ [ATA_LPM_UNKNOWN] = "max_performance",
+ [ATA_LPM_MAX_POWER] = "max_performance",
+ [ATA_LPM_MED_POWER] = "medium_power",
+ [ATA_LPM_MED_POWER_WITH_DIPM] = "med_power_with_dipm",
+ [ATA_LPM_MIN_POWER_WITH_PARTIAL] = "min_power_with_partial",
+ [ATA_LPM_MIN_POWER] = "min_power",
+};
+
+static ssize_t ata_scsi_lpm_store(struct device *device,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct Scsi_Host *shost = class_to_shost(device);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ struct ata_link *link;
+ struct ata_device *dev;
+ enum ata_lpm_policy policy;
+ unsigned long flags;
+
+ /* UNKNOWN is internal state, iterate from MAX_POWER */
+ for (policy = ATA_LPM_MAX_POWER;
+ policy < ARRAY_SIZE(ata_lpm_policy_names); policy++) {
+ const char *name = ata_lpm_policy_names[policy];
+
+ if (strncmp(name, buf, strlen(name)) == 0)
+ break;
+ }
+ if (policy == ARRAY_SIZE(ata_lpm_policy_names))
+ return -EINVAL;
+
+ spin_lock_irqsave(ap->lock, flags);
+
+ ata_for_each_link(link, ap, EDGE) {
+ ata_for_each_dev(dev, &ap->link, ENABLED) {
+ if (dev->horkage & ATA_HORKAGE_NOLPM) {
+ count = -EOPNOTSUPP;
+ goto out_unlock;
+ }
+ }
+ }
+
+ ap->target_lpm_policy = policy;
+ ata_port_schedule_eh(ap);
+out_unlock:
+ spin_unlock_irqrestore(ap->lock, flags);
+ return count;
+}
+
+static ssize_t ata_scsi_lpm_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+
+ if (ap->target_lpm_policy >= ARRAY_SIZE(ata_lpm_policy_names))
+ return -EINVAL;
+
+ return snprintf(buf, PAGE_SIZE, "%s\n",
+ ata_lpm_policy_names[ap->target_lpm_policy]);
+}
+DEVICE_ATTR(link_power_management_policy, S_IRUGO | S_IWUSR,
+ ata_scsi_lpm_show, ata_scsi_lpm_store);
+EXPORT_SYMBOL_GPL(dev_attr_link_power_management_policy);
+
+static ssize_t ata_ncq_prio_enable_show(struct device *device,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct scsi_device *sdev = to_scsi_device(device);
+ struct ata_port *ap;
+ struct ata_device *dev;
+ bool ncq_prio_enable;
+ int rc = 0;
+
+ ap = ata_shost_to_port(sdev->host);
+
+ spin_lock_irq(ap->lock);
+ dev = ata_scsi_find_dev(ap, sdev);
+ if (!dev) {
+ rc = -ENODEV;
+ goto unlock;
+ }
+
+ ncq_prio_enable = dev->flags & ATA_DFLAG_NCQ_PRIO_ENABLE;
+
+unlock:
+ spin_unlock_irq(ap->lock);
+
+ return rc ? rc : snprintf(buf, 20, "%u\n", ncq_prio_enable);
+}
+
+static ssize_t ata_ncq_prio_enable_store(struct device *device,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct scsi_device *sdev = to_scsi_device(device);
+ struct ata_port *ap;
+ struct ata_device *dev;
+ long int input;
+ int rc;
+
+ rc = kstrtol(buf, 10, &input);
+ if (rc)
+ return rc;
+ if ((input < 0) || (input > 1))
+ return -EINVAL;
+
+ ap = ata_shost_to_port(sdev->host);
+ dev = ata_scsi_find_dev(ap, sdev);
+ if (unlikely(!dev))
+ return -ENODEV;
+
+ spin_lock_irq(ap->lock);
+ if (input)
+ dev->flags |= ATA_DFLAG_NCQ_PRIO_ENABLE;
+ else
+ dev->flags &= ~ATA_DFLAG_NCQ_PRIO_ENABLE;
+
+ dev->link->eh_info.action |= ATA_EH_REVALIDATE;
+ dev->link->eh_info.flags |= ATA_EHI_QUIET;
+ ata_port_schedule_eh(ap);
+ spin_unlock_irq(ap->lock);
+
+ ata_port_wait_eh(ap);
+
+ if (input) {
+ spin_lock_irq(ap->lock);
+ if (!(dev->flags & ATA_DFLAG_NCQ_PRIO)) {
+ dev->flags &= ~ATA_DFLAG_NCQ_PRIO_ENABLE;
+ rc = -EIO;
+ }
+ spin_unlock_irq(ap->lock);
+ }
+
+ return rc ? rc : len;
+}
+
+DEVICE_ATTR(ncq_prio_enable, S_IRUGO | S_IWUSR,
+ ata_ncq_prio_enable_show, ata_ncq_prio_enable_store);
+EXPORT_SYMBOL_GPL(dev_attr_ncq_prio_enable);
+
+struct device_attribute *ata_ncq_sdev_attrs[] = {
+ &dev_attr_unload_heads,
+ &dev_attr_ncq_prio_enable,
+ NULL
+};
+EXPORT_SYMBOL_GPL(ata_ncq_sdev_attrs);
+
+static ssize_t
+ata_scsi_em_message_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+ if (ap->ops->em_store && (ap->flags & ATA_FLAG_EM))
+ return ap->ops->em_store(ap, buf, count);
+ return -EINVAL;
+}
+
+static ssize_t
+ata_scsi_em_message_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+
+ if (ap->ops->em_show && (ap->flags & ATA_FLAG_EM))
+ return ap->ops->em_show(ap, buf);
+ return -EINVAL;
+}
+DEVICE_ATTR(em_message, S_IRUGO | S_IWUSR,
+ ata_scsi_em_message_show, ata_scsi_em_message_store);
+EXPORT_SYMBOL_GPL(dev_attr_em_message);
+
+static ssize_t
+ata_scsi_em_message_type_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct Scsi_Host *shost = class_to_shost(dev);
+ struct ata_port *ap = ata_shost_to_port(shost);
+
+ return snprintf(buf, 23, "%d\n", ap->em_message_type);
+}
+DEVICE_ATTR(em_message_type, S_IRUGO,
+ ata_scsi_em_message_type_show, NULL);
+EXPORT_SYMBOL_GPL(dev_attr_em_message_type);
+
+static ssize_t
+ata_scsi_activity_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct scsi_device *sdev = to_scsi_device(dev);
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
+
+ if (atadev && ap->ops->sw_activity_show &&
+ (ap->flags & ATA_FLAG_SW_ACTIVITY))
+ return ap->ops->sw_activity_show(atadev, buf);
+ return -EINVAL;
+}
+
+static ssize_t
+ata_scsi_activity_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct scsi_device *sdev = to_scsi_device(dev);
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+ struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
+ enum sw_activity val;
+ int rc;
+
+ if (atadev && ap->ops->sw_activity_store &&
+ (ap->flags & ATA_FLAG_SW_ACTIVITY)) {
+ val = simple_strtoul(buf, NULL, 0);
+ switch (val) {
+ case OFF: case BLINK_ON: case BLINK_OFF:
+ rc = ap->ops->sw_activity_store(atadev, val);
+ if (!rc)
+ return count;
+ else
+ return rc;
+ }
+ }
+ return -EINVAL;
+}
+DEVICE_ATTR(sw_activity, S_IWUSR | S_IRUGO, ata_scsi_activity_show,
+ ata_scsi_activity_store);
+EXPORT_SYMBOL_GPL(dev_attr_sw_activity);
+
+/**
+ * __ata_change_queue_depth - helper for ata_scsi_change_queue_depth
+ * @ap: ATA port to which the device change the queue depth
+ * @sdev: SCSI device to configure queue depth for
+ * @queue_depth: new queue depth
+ *
+ * libsas and libata have different approaches for associating a sdev to
+ * its ata_port.
+ *
+ */
+int __ata_change_queue_depth(struct ata_port *ap, struct scsi_device *sdev,
+ int queue_depth)
+{
+ struct ata_device *dev;
+ unsigned long flags;
+
+ if (queue_depth < 1 || queue_depth == sdev->queue_depth)
+ return sdev->queue_depth;
+
+ dev = ata_scsi_find_dev(ap, sdev);
+ if (!dev || !ata_dev_enabled(dev))
+ return sdev->queue_depth;
+
+ /* NCQ enabled? */
+ spin_lock_irqsave(ap->lock, flags);
+ dev->flags &= ~ATA_DFLAG_NCQ_OFF;
+ if (queue_depth == 1 || !ata_ncq_enabled(dev)) {
+ dev->flags |= ATA_DFLAG_NCQ_OFF;
+ queue_depth = 1;
+ }
+ spin_unlock_irqrestore(ap->lock, flags);
+
+ /* limit and apply queue depth */
+ queue_depth = min(queue_depth, sdev->host->can_queue);
+ queue_depth = min(queue_depth, ata_id_queue_depth(dev->id));
+ queue_depth = min(queue_depth, ATA_MAX_QUEUE);
+
+ if (sdev->queue_depth == queue_depth)
+ return -EINVAL;
+
+ return scsi_change_queue_depth(sdev, queue_depth);
+}
+EXPORT_SYMBOL_GPL(__ata_change_queue_depth);
+
+/**
+ * ata_scsi_change_queue_depth - SCSI callback for queue depth config
+ * @sdev: SCSI device to configure queue depth for
+ * @queue_depth: new queue depth
+ *
+ * This is libata standard hostt->change_queue_depth callback.
+ * SCSI will call into this callback when user tries to set queue
+ * depth via sysfs.
+ *
+ * LOCKING:
+ * SCSI layer (we don't care)
+ *
+ * RETURNS:
+ * Newly configured queue depth.
+ */
+int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
+{
+ struct ata_port *ap = ata_shost_to_port(sdev->host);
+
+ return __ata_change_queue_depth(ap, sdev, queue_depth);
+}
+EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index b8e41c8e6395..6d295d0396d0 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -45,8 +45,6 @@ typedef unsigned int (*ata_xlat_func_t)(struct ata_queued_cmd *qc);
static struct ata_device *__ata_scsi_find_dev(struct ata_port *ap,
const struct scsi_device *scsidev);
-static struct ata_device *ata_scsi_find_dev(struct ata_port *ap,
- const struct scsi_device *scsidev);
#define RW_RECOVERY_MPAGE 0x1
#define RW_RECOVERY_MPAGE_LEN 12
@@ -86,71 +84,6 @@ static const u8 def_control_mpage[CONTROL_MPAGE_LEN] = {
0, 30 /* extended self test time, see 05-359r1 */
};
-static const char *ata_lpm_policy_names[] = {
- [ATA_LPM_UNKNOWN] = "max_performance",
- [ATA_LPM_MAX_POWER] = "max_performance",
- [ATA_LPM_MED_POWER] = "medium_power",
- [ATA_LPM_MED_POWER_WITH_DIPM] = "med_power_with_dipm",
- [ATA_LPM_MIN_POWER_WITH_PARTIAL] = "min_power_with_partial",
- [ATA_LPM_MIN_POWER] = "min_power",
-};
-
-static ssize_t ata_scsi_lpm_store(struct device *device,
- struct device_attribute *attr,
- const char *buf, size_t count)
-{
- struct Scsi_Host *shost = class_to_shost(device);
- struct ata_port *ap = ata_shost_to_port(shost);
- struct ata_link *link;
- struct ata_device *dev;
- enum ata_lpm_policy policy;
- unsigned long flags;
-
- /* UNKNOWN is internal state, iterate from MAX_POWER */
- for (policy = ATA_LPM_MAX_POWER;
- policy < ARRAY_SIZE(ata_lpm_policy_names); policy++) {
- const char *name = ata_lpm_policy_names[policy];
-
- if (strncmp(name, buf, strlen(name)) == 0)
- break;
- }
- if (policy == ARRAY_SIZE(ata_lpm_policy_names))
- return -EINVAL;
-
- spin_lock_irqsave(ap->lock, flags);
-
- ata_for_each_link(link, ap, EDGE) {
- ata_for_each_dev(dev, &ap->link, ENABLED) {
- if (dev->horkage & ATA_HORKAGE_NOLPM) {
- count = -EOPNOTSUPP;
- goto out_unlock;
- }
- }
- }
-
- ap->target_lpm_policy = policy;
- ata_port_schedule_eh(ap);
-out_unlock:
- spin_unlock_irqrestore(ap->lock, flags);
- return count;
-}
-
-static ssize_t ata_scsi_lpm_show(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
-
- if (ap->target_lpm_policy >= ARRAY_SIZE(ata_lpm_policy_names))
- return -EINVAL;
-
- return snprintf(buf, PAGE_SIZE, "%s\n",
- ata_lpm_policy_names[ap->target_lpm_policy]);
-}
-DEVICE_ATTR(link_power_management_policy, S_IRUGO | S_IWUSR,
- ata_scsi_lpm_show, ata_scsi_lpm_store);
-EXPORT_SYMBOL_GPL(dev_attr_link_power_management_policy);
-
static ssize_t ata_scsi_park_show(struct device *device,
struct device_attribute *attr, char *buf)
{
@@ -254,83 +187,6 @@ DEVICE_ATTR(unload_heads, S_IRUGO | S_IWUSR,
ata_scsi_park_show, ata_scsi_park_store);
EXPORT_SYMBOL_GPL(dev_attr_unload_heads);
-static ssize_t ata_ncq_prio_enable_show(struct device *device,
- struct device_attribute *attr,
- char *buf)
-{
- struct scsi_device *sdev = to_scsi_device(device);
- struct ata_port *ap;
- struct ata_device *dev;
- bool ncq_prio_enable;
- int rc = 0;
-
- ap = ata_shost_to_port(sdev->host);
-
- spin_lock_irq(ap->lock);
- dev = ata_scsi_find_dev(ap, sdev);
- if (!dev) {
- rc = -ENODEV;
- goto unlock;
- }
-
- ncq_prio_enable = dev->flags & ATA_DFLAG_NCQ_PRIO_ENABLE;
-
-unlock:
- spin_unlock_irq(ap->lock);
-
- return rc ? rc : snprintf(buf, 20, "%u\n", ncq_prio_enable);
-}
-
-static ssize_t ata_ncq_prio_enable_store(struct device *device,
- struct device_attribute *attr,
- const char *buf, size_t len)
-{
- struct scsi_device *sdev = to_scsi_device(device);
- struct ata_port *ap;
- struct ata_device *dev;
- long int input;
- int rc;
-
- rc = kstrtol(buf, 10, &input);
- if (rc)
- return rc;
- if ((input < 0) || (input > 1))
- return -EINVAL;
-
- ap = ata_shost_to_port(sdev->host);
- dev = ata_scsi_find_dev(ap, sdev);
- if (unlikely(!dev))
- return -ENODEV;
-
- spin_lock_irq(ap->lock);
- if (input)
- dev->flags |= ATA_DFLAG_NCQ_PRIO_ENABLE;
- else
- dev->flags &= ~ATA_DFLAG_NCQ_PRIO_ENABLE;
-
- dev->link->eh_info.action |= ATA_EH_REVALIDATE;
- dev->link->eh_info.flags |= ATA_EHI_QUIET;
- ata_port_schedule_eh(ap);
- spin_unlock_irq(ap->lock);
-
- ata_port_wait_eh(ap);
-
- if (input) {
- spin_lock_irq(ap->lock);
- if (!(dev->flags & ATA_DFLAG_NCQ_PRIO)) {
- dev->flags &= ~ATA_DFLAG_NCQ_PRIO_ENABLE;
- rc = -EIO;
- }
- spin_unlock_irq(ap->lock);
- }
-
- return rc ? rc : len;
-}
-
-DEVICE_ATTR(ncq_prio_enable, S_IRUGO | S_IWUSR,
- ata_ncq_prio_enable_show, ata_ncq_prio_enable_store);
-EXPORT_SYMBOL_GPL(dev_attr_ncq_prio_enable);
-
void ata_scsi_set_sense(struct ata_device *dev, struct scsi_cmnd *cmd,
u8 sk, u8 asc, u8 ascq)
{
@@ -379,100 +235,12 @@ static void ata_scsi_set_invalid_parameter(struct ata_device *dev,
field, 0xff, 0);
}
-static ssize_t
-ata_scsi_em_message_store(struct device *dev, struct device_attribute *attr,
- const char *buf, size_t count)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
- if (ap->ops->em_store && (ap->flags & ATA_FLAG_EM))
- return ap->ops->em_store(ap, buf, count);
- return -EINVAL;
-}
-
-static ssize_t
-ata_scsi_em_message_show(struct device *dev, struct device_attribute *attr,
- char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
-
- if (ap->ops->em_show && (ap->flags & ATA_FLAG_EM))
- return ap->ops->em_show(ap, buf);
- return -EINVAL;
-}
-DEVICE_ATTR(em_message, S_IRUGO | S_IWUSR,
- ata_scsi_em_message_show, ata_scsi_em_message_store);
-EXPORT_SYMBOL_GPL(dev_attr_em_message);
-
-static ssize_t
-ata_scsi_em_message_type_show(struct device *dev, struct device_attribute *attr,
- char *buf)
-{
- struct Scsi_Host *shost = class_to_shost(dev);
- struct ata_port *ap = ata_shost_to_port(shost);
-
- return snprintf(buf, 23, "%d\n", ap->em_message_type);
-}
-DEVICE_ATTR(em_message_type, S_IRUGO,
- ata_scsi_em_message_type_show, NULL);
-EXPORT_SYMBOL_GPL(dev_attr_em_message_type);
-
-static ssize_t
-ata_scsi_activity_show(struct device *dev, struct device_attribute *attr,
- char *buf)
-{
- struct scsi_device *sdev = to_scsi_device(dev);
- struct ata_port *ap = ata_shost_to_port(sdev->host);
- struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
-
- if (atadev && ap->ops->sw_activity_show &&
- (ap->flags & ATA_FLAG_SW_ACTIVITY))
- return ap->ops->sw_activity_show(atadev, buf);
- return -EINVAL;
-}
-
-static ssize_t
-ata_scsi_activity_store(struct device *dev, struct device_attribute *attr,
- const char *buf, size_t count)
-{
- struct scsi_device *sdev = to_scsi_device(dev);
- struct ata_port *ap = ata_shost_to_port(sdev->host);
- struct ata_device *atadev = ata_scsi_find_dev(ap, sdev);
- enum sw_activity val;
- int rc;
-
- if (atadev && ap->ops->sw_activity_store &&
- (ap->flags & ATA_FLAG_SW_ACTIVITY)) {
- val = simple_strtoul(buf, NULL, 0);
- switch (val) {
- case OFF: case BLINK_ON: case BLINK_OFF:
- rc = ap->ops->sw_activity_store(atadev, val);
- if (!rc)
- return count;
- else
- return rc;
- }
- }
- return -EINVAL;
-}
-DEVICE_ATTR(sw_activity, S_IWUSR | S_IRUGO, ata_scsi_activity_show,
- ata_scsi_activity_store);
-EXPORT_SYMBOL_GPL(dev_attr_sw_activity);
-
struct device_attribute *ata_common_sdev_attrs[] = {
&dev_attr_unload_heads,
NULL
};
EXPORT_SYMBOL_GPL(ata_common_sdev_attrs);
-struct device_attribute *ata_ncq_sdev_attrs[] = {
- &dev_attr_unload_heads,
- &dev_attr_ncq_prio_enable,
- NULL
-};
-EXPORT_SYMBOL_GPL(ata_ncq_sdev_attrs);
-
/**
* ata_std_bios_param - generic bios head/sector/cylinder calculator used by sd.
* @sdev: SCSI device for which BIOS geometry is to be determined
@@ -1390,73 +1158,6 @@ void ata_scsi_slave_destroy(struct scsi_device *sdev)
}
EXPORT_SYMBOL_GPL(ata_scsi_slave_destroy);
-/**
- * __ata_change_queue_depth - helper for ata_scsi_change_queue_depth
- * @ap: ATA port to which the device change the queue depth
- * @sdev: SCSI device to configure queue depth for
- * @queue_depth: new queue depth
- *
- * libsas and libata have different approaches for associating a sdev to
- * its ata_port.
- *
- */
-int __ata_change_queue_depth(struct ata_port *ap, struct scsi_device *sdev,
- int queue_depth)
-{
- struct ata_device *dev;
- unsigned long flags;
-
- if (queue_depth < 1 || queue_depth == sdev->queue_depth)
- return sdev->queue_depth;
-
- dev = ata_scsi_find_dev(ap, sdev);
- if (!dev || !ata_dev_enabled(dev))
- return sdev->queue_depth;
-
- /* NCQ enabled? */
- spin_lock_irqsave(ap->lock, flags);
- dev->flags &= ~ATA_DFLAG_NCQ_OFF;
- if (queue_depth == 1 || !ata_ncq_enabled(dev)) {
- dev->flags |= ATA_DFLAG_NCQ_OFF;
- queue_depth = 1;
- }
- spin_unlock_irqrestore(ap->lock, flags);
-
- /* limit and apply queue depth */
- queue_depth = min(queue_depth, sdev->host->can_queue);
- queue_depth = min(queue_depth, ata_id_queue_depth(dev->id));
- queue_depth = min(queue_depth, ATA_MAX_QUEUE);
-
- if (sdev->queue_depth == queue_depth)
- return -EINVAL;
-
- return scsi_change_queue_depth(sdev, queue_depth);
-}
-EXPORT_SYMBOL_GPL(__ata_change_queue_depth);
-
-/**
- * ata_scsi_change_queue_depth - SCSI callback for queue depth config
- * @sdev: SCSI device to configure queue depth for
- * @queue_depth: new queue depth
- *
- * This is libata standard hostt->change_queue_depth callback.
- * SCSI will call into this callback when user tries to set queue
- * depth via sysfs.
- *
- * LOCKING:
- * SCSI layer (we don't care)
- *
- * RETURNS:
- * Newly configured queue depth.
- */
-int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
-{
- struct ata_port *ap = ata_shost_to_port(sdev->host);
-
- return __ata_change_queue_depth(ap, sdev, queue_depth);
-}
-EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
-
/**
* ata_scsi_start_stop_xlat - Translate SCSI START STOP UNIT command
* @qc: Storage for translated ATA taskfile
@@ -3093,7 +2794,7 @@ static struct ata_device *__ata_scsi_find_dev(struct ata_port *ap,
* RETURNS:
* Associated ATA device, or %NULL if not found.
*/
-static struct ata_device *
+struct ata_device *
ata_scsi_find_dev(struct ata_port *ap, const struct scsi_device *scsidev)
{
struct ata_device *dev = __ata_scsi_find_dev(ap, scsidev);
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index cd8090ad43e5..ce3f3c039572 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -112,6 +112,8 @@ static inline void ata_acpi_bind_dev(struct ata_device *dev) {}
#endif
/* libata-scsi.c */
+extern struct ata_device *ata_scsi_find_dev(struct ata_port *ap,
+ const struct scsi_device *scsidev);
extern int ata_scsi_add_hosts(struct ata_host *host,
struct scsi_host_template *sht);
extern void ata_scsi_scan_host(struct ata_port *ap, int sync);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 99cd52a5a4c2..08c4c365fd98 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -532,12 +532,14 @@ typedef int (*ata_reset_fn_t)(struct ata_link *link, unsigned int *classes,
unsigned long deadline);
typedef void (*ata_postreset_fn_t)(struct ata_link *link, unsigned int *classes);
-extern struct device_attribute dev_attr_link_power_management_policy;
extern struct device_attribute dev_attr_unload_heads;
+#ifdef CONFIG_SATA_HOST
+extern struct device_attribute dev_attr_link_power_management_policy;
extern struct device_attribute dev_attr_ncq_prio_enable;
extern struct device_attribute dev_attr_em_message_type;
extern struct device_attribute dev_attr_em_message;
extern struct device_attribute dev_attr_sw_activity;
+#endif
enum sw_activity {
OFF,
@@ -1373,7 +1375,6 @@ extern int ata_link_nr_enabled(struct ata_link *link);
extern const struct ata_port_operations ata_base_port_ops;
extern const struct ata_port_operations sata_port_ops;
extern struct device_attribute *ata_common_sdev_attrs[];
-extern struct device_attribute *ata_ncq_sdev_attrs[];
/*
* All sht initializers (BASE, PIO, BMDMA, NCQ) must be instantiated
@@ -1398,10 +1399,14 @@ extern struct device_attribute *ata_ncq_sdev_attrs[];
.unlock_native_capacity = ata_scsi_unlock_native_capacity, \
.sdev_attrs = ata_common_sdev_attrs
+#ifdef CONFIG_SATA_HOST
+extern struct device_attribute *ata_ncq_sdev_attrs[];
+
#define ATA_NCQ_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
.sdev_attrs = ata_ncq_sdev_attrs, \
.change_queue_depth = ata_scsi_change_queue_depth
+#endif
/*
* PMP helpers
--
2.24.1
* move ata_eh_analyze_ncq_error() and ata_eh_read_log_10h() to
libata-sata.c
* add static inline for ata_eh_analyze_ncq_error() for
CONFIG_SATA_HOST=n case (link->sactive is non-zero only if
NCQ commands are actually queued so empty function body is
sufficient)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
16164 18 0 16182 3f36 drivers/ata/libata-eh.o
after:
15446 18 0 15464 3c68 drivers/ata/libata-eh.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-eh.c | 131 --------------------------------------
drivers/ata/libata-sata.c | 131 ++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 3 +-
3 files changed, 133 insertions(+), 132 deletions(-)
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index ef4d606cd8c6..474c6c34fe02 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1351,62 +1351,6 @@ static const char *ata_err_string(unsigned int err_mask)
return "unknown error";
}
-/**
- * ata_eh_read_log_10h - Read log page 10h for NCQ error details
- * @dev: Device to read log page 10h from
- * @tag: Resulting tag of the failed command
- * @tf: Resulting taskfile registers of the failed command
- *
- * Read log page 10h to obtain NCQ error details and clear error
- * condition.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-static int ata_eh_read_log_10h(struct ata_device *dev,
- int *tag, struct ata_taskfile *tf)
-{
- u8 *buf = dev->link->ap->sector_buf;
- unsigned int err_mask;
- u8 csum;
- int i;
-
- err_mask = ata_read_log_page(dev, ATA_LOG_SATA_NCQ, 0, buf, 1);
- if (err_mask)
- return -EIO;
-
- csum = 0;
- for (i = 0; i < ATA_SECT_SIZE; i++)
- csum += buf[i];
- if (csum)
- ata_dev_warn(dev, "invalid checksum 0x%x on log page 10h\n",
- csum);
-
- if (buf[0] & 0x80)
- return -ENOENT;
-
- *tag = buf[0] & 0x1f;
-
- tf->command = buf[2];
- tf->feature = buf[3];
- tf->lbal = buf[4];
- tf->lbam = buf[5];
- tf->lbah = buf[6];
- tf->device = buf[7];
- tf->hob_lbal = buf[8];
- tf->hob_lbam = buf[9];
- tf->hob_lbah = buf[10];
- tf->nsect = buf[12];
- tf->hob_nsect = buf[13];
- if (dev->class == ATA_DEV_ZAC && ata_id_has_ncq_autosense(dev->id))
- tf->auxiliary = buf[14] << 16 | buf[15] << 8 | buf[16];
-
- return 0;
-}
-
/**
* atapi_eh_tur - perform ATAPI TEST_UNIT_READY
* @dev: target ATAPI device
@@ -1590,81 +1534,6 @@ static void ata_eh_analyze_serror(struct ata_link *link)
ehc->i.action |= action;
}
-/**
- * ata_eh_analyze_ncq_error - analyze NCQ error
- * @link: ATA link to analyze NCQ error for
- *
- * Read log page 10h, determine the offending qc and acquire
- * error status TF. For NCQ device errors, all LLDDs have to do
- * is setting AC_ERR_DEV in ehi->err_mask. This function takes
- * care of the rest.
- *
- * LOCKING:
- * Kernel thread context (may sleep).
- */
-void ata_eh_analyze_ncq_error(struct ata_link *link)
-{
- struct ata_port *ap = link->ap;
- struct ata_eh_context *ehc = &link->eh_context;
- struct ata_device *dev = link->device;
- struct ata_queued_cmd *qc;
- struct ata_taskfile tf;
- int tag, rc;
-
- /* if frozen, we can't do much */
- if (ap->pflags & ATA_PFLAG_FROZEN)
- return;
-
- /* is it NCQ device error? */
- if (!link->sactive || !(ehc->i.err_mask & AC_ERR_DEV))
- return;
-
- /* has LLDD analyzed already? */
- ata_qc_for_each_raw(ap, qc, tag) {
- if (!(qc->flags & ATA_QCFLAG_FAILED))
- continue;
-
- if (qc->err_mask)
- return;
- }
-
- /* okay, this error is ours */
- memset(&tf, 0, sizeof(tf));
- rc = ata_eh_read_log_10h(dev, &tag, &tf);
- if (rc) {
- ata_link_err(link, "failed to read log page 10h (errno=%d)\n",
- rc);
- return;
- }
-
- if (!(link->sactive & (1 << tag))) {
- ata_link_err(link, "log page 10h reported inactive tag %d\n",
- tag);
- return;
- }
-
- /* we've got the perpetrator, condemn it */
- qc = __ata_qc_from_tag(ap, tag);
- memcpy(&qc->result_tf, &tf, sizeof(tf));
- qc->result_tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_LBA | ATA_TFLAG_LBA48;
- qc->err_mask |= AC_ERR_DEV | AC_ERR_NCQ;
- if (dev->class == ATA_DEV_ZAC &&
- ((qc->result_tf.command & ATA_SENSE) || qc->result_tf.auxiliary)) {
- char sense_key, asc, ascq;
-
- sense_key = (qc->result_tf.auxiliary >> 16) & 0xff;
- asc = (qc->result_tf.auxiliary >> 8) & 0xff;
- ascq = qc->result_tf.auxiliary & 0xff;
- ata_scsi_set_sense(dev, qc->scsicmd, sense_key, asc, ascq);
- ata_scsi_set_sense_information(dev, qc->scsicmd,
- &qc->result_tf);
- qc->flags |= ATA_QCFLAG_SENSE_VALID;
- }
-
- ehc->i.err_mask &= ~AC_ERR_DEV;
-}
-EXPORT_SYMBOL_GPL(ata_eh_analyze_ncq_error);
-
/**
* ata_eh_analyze_tf - analyze taskfile of a failed qc
* @qc: qc to analyze
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 008468e516cd..c16423e44525 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -1350,3 +1350,134 @@ int sata_async_notification(struct ata_port *ap)
}
}
EXPORT_SYMBOL_GPL(sata_async_notification);
+
+/**
+ * ata_eh_read_log_10h - Read log page 10h for NCQ error details
+ * @dev: Device to read log page 10h from
+ * @tag: Resulting tag of the failed command
+ * @tf: Resulting taskfile registers of the failed command
+ *
+ * Read log page 10h to obtain NCQ error details and clear error
+ * condition.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep).
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+static int ata_eh_read_log_10h(struct ata_device *dev,
+ int *tag, struct ata_taskfile *tf)
+{
+ u8 *buf = dev->link->ap->sector_buf;
+ unsigned int err_mask;
+ u8 csum;
+ int i;
+
+ err_mask = ata_read_log_page(dev, ATA_LOG_SATA_NCQ, 0, buf, 1);
+ if (err_mask)
+ return -EIO;
+
+ csum = 0;
+ for (i = 0; i < ATA_SECT_SIZE; i++)
+ csum += buf[i];
+ if (csum)
+ ata_dev_warn(dev, "invalid checksum 0x%x on log page 10h\n",
+ csum);
+
+ if (buf[0] & 0x80)
+ return -ENOENT;
+
+ *tag = buf[0] & 0x1f;
+
+ tf->command = buf[2];
+ tf->feature = buf[3];
+ tf->lbal = buf[4];
+ tf->lbam = buf[5];
+ tf->lbah = buf[6];
+ tf->device = buf[7];
+ tf->hob_lbal = buf[8];
+ tf->hob_lbam = buf[9];
+ tf->hob_lbah = buf[10];
+ tf->nsect = buf[12];
+ tf->hob_nsect = buf[13];
+ if (dev->class == ATA_DEV_ZAC && ata_id_has_ncq_autosense(dev->id))
+ tf->auxiliary = buf[14] << 16 | buf[15] << 8 | buf[16];
+
+ return 0;
+}
+
+/**
+ * ata_eh_analyze_ncq_error - analyze NCQ error
+ * @link: ATA link to analyze NCQ error for
+ *
+ * Read log page 10h, determine the offending qc and acquire
+ * error status TF. For NCQ device errors, all LLDDs have to do
+ * is setting AC_ERR_DEV in ehi->err_mask. This function takes
+ * care of the rest.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep).
+ */
+void ata_eh_analyze_ncq_error(struct ata_link *link)
+{
+ struct ata_port *ap = link->ap;
+ struct ata_eh_context *ehc = &link->eh_context;
+ struct ata_device *dev = link->device;
+ struct ata_queued_cmd *qc;
+ struct ata_taskfile tf;
+ int tag, rc;
+
+ /* if frozen, we can't do much */
+ if (ap->pflags & ATA_PFLAG_FROZEN)
+ return;
+
+ /* is it NCQ device error? */
+ if (!link->sactive || !(ehc->i.err_mask & AC_ERR_DEV))
+ return;
+
+ /* has LLDD analyzed already? */
+ ata_qc_for_each_raw(ap, qc, tag) {
+ if (!(qc->flags & ATA_QCFLAG_FAILED))
+ continue;
+
+ if (qc->err_mask)
+ return;
+ }
+
+ /* okay, this error is ours */
+ memset(&tf, 0, sizeof(tf));
+ rc = ata_eh_read_log_10h(dev, &tag, &tf);
+ if (rc) {
+ ata_link_err(link, "failed to read log page 10h (errno=%d)\n",
+ rc);
+ return;
+ }
+
+ if (!(link->sactive & (1 << tag))) {
+ ata_link_err(link, "log page 10h reported inactive tag %d\n",
+ tag);
+ return;
+ }
+
+ /* we've got the perpetrator, condemn it */
+ qc = __ata_qc_from_tag(ap, tag);
+ memcpy(&qc->result_tf, &tf, sizeof(tf));
+ qc->result_tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_LBA | ATA_TFLAG_LBA48;
+ qc->err_mask |= AC_ERR_DEV | AC_ERR_NCQ;
+ if (dev->class == ATA_DEV_ZAC &&
+ ((qc->result_tf.command & ATA_SENSE) || qc->result_tf.auxiliary)) {
+ char sense_key, asc, ascq;
+
+ sense_key = (qc->result_tf.auxiliary >> 16) & 0xff;
+ asc = (qc->result_tf.auxiliary >> 8) & 0xff;
+ ascq = qc->result_tf.auxiliary & 0xff;
+ ata_scsi_set_sense(dev, qc->scsicmd, sense_key, asc, ascq);
+ ata_scsi_set_sense_information(dev, qc->scsicmd,
+ &qc->result_tf);
+ qc->flags |= ATA_QCFLAG_SENSE_VALID;
+ }
+
+ ehc->i.err_mask &= ~AC_ERR_DEV;
+}
+EXPORT_SYMBOL_GPL(ata_eh_analyze_ncq_error);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 6d6fb25cc650..23277eddb54e 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1183,6 +1183,7 @@ extern int sata_link_hardreset(struct ata_link *link,
bool *online, int (*check_ready)(struct ata_link *));
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
+extern void ata_eh_analyze_ncq_error(struct ata_link *link);
#else
static inline const unsigned long *
sata_ehc_deb_timing(struct ata_eh_context *ehc)
@@ -1219,6 +1220,7 @@ static inline int sata_link_resume(struct ata_link *link,
{
return -EOPNOTSUPP;
}
+static inline void ata_eh_analyze_ncq_error(struct ata_link *link) { }
#endif
extern int sata_link_debounce(struct ata_link *link,
const unsigned long *params, unsigned long deadline);
@@ -1341,7 +1343,6 @@ extern void ata_eh_thaw_port(struct ata_port *ap);
extern void ata_eh_qc_complete(struct ata_queued_cmd *qc);
extern void ata_eh_qc_retry(struct ata_queued_cmd *qc);
-extern void ata_eh_analyze_ncq_error(struct ata_link *link);
extern void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
--
2.24.1
Add ATA_FORCE config option (visible only if EXPERT config
option is enabled) and make "libata.force" kernel parameter
optional.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
w/ CONFIG_ATA_FORCE=y:
31983 572 40 32595 7f53 drivers/ata/libata-core.o
w/ CONFIG_ATA_FROCE=n:
28958 316 32 29306 727a drivers/ata/libata-core.o
Suggested-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/Kconfig | 16 ++++++++++++++++
drivers/ata/libata-core.c | 22 ++++++++++++++++++++--
drivers/ata/libata.h | 4 ++++
3 files changed, 40 insertions(+), 2 deletions(-)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 5b55ebf56b5a..05ecdce1b702 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -51,6 +51,22 @@ config ATA_VERBOSE_ERROR
If unsure, say Y.
+config ATA_FORCE
+ bool "\"libata.force=\" kernel parameter support" if EXPERT
+ default y
+ help
+ This option adds support for "libata.force=" kernel parameter for
+ forcing configuration settings.
+
+ For further information, please read
+ <file:Documentation/admin-guide/kernel-parameters.txt>.
+
+ This option will enlarge the kernel by approx. 3KB. Disable it if
+ kernel size is more important than ability to override the default
+ configuration settings.
+
+ If unsure, say Y.
+
config ATA_ACPI
bool "ATA ACPI Support"
depends on ACPI
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 20c22dbc1f24..beca5f91bb4c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -89,6 +89,7 @@ static unsigned long ata_dev_blacklisted(const struct ata_device *dev);
atomic_t ata_print_id = ATOMIC_INIT(0);
+#ifdef CONFIG_ATA_FORCE
struct ata_force_param {
const char *name;
u8 cbl;
@@ -112,6 +113,7 @@ static char ata_force_param_buf[COMMAND_LINE_SIZE] __initdata;
/* param_buf is thrown away after initialization, disallow read */
module_param_string(force, ata_force_param_buf, sizeof(ata_force_param_buf), 0);
MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link speed and transfer mode (see Documentation/admin-guide/kernel-parameters.rst for details)");
+#endif
static int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
@@ -303,6 +305,7 @@ struct ata_link *ata_dev_phys_link(struct ata_device *dev)
return ap->slave_link;
}
+#ifdef CONFIG_ATA_FORCE
/**
* ata_force_cbl - force cable type according to libata.force
* @ap: ATA port of interest
@@ -483,6 +486,11 @@ static void ata_force_horkage(struct ata_device *dev)
fe->param.name);
}
}
+#else
+static inline void ata_force_link_limits(struct ata_link *link) { }
+static inline void ata_force_xfermask(struct ata_device *dev) { }
+static inline void ata_force_horkage(struct ata_device *dev) { }
+#endif
/**
* atapi_cmd_type - Determine ATAPI command type from SCSI opcode
@@ -6080,6 +6088,7 @@ int ata_platform_remove_one(struct platform_device *pdev)
}
EXPORT_SYMBOL_GPL(ata_platform_remove_one);
+#ifdef CONFIG_ATA_FORCE
static int __init ata_parse_force_one(char **cur,
struct ata_force_ent *force_ent,
const char **reason)
@@ -6259,6 +6268,15 @@ static void __init ata_parse_force_param(void)
ata_force_tbl_size = idx;
}
+static void ata_free_force_param(void)
+{
+ kfree(ata_force_tbl);
+}
+#else
+static inline void ata_parse_force_param(void) { }
+static inline void ata_free_force_param(void) { }
+#endif
+
static int __init ata_init(void)
{
int rc;
@@ -6267,7 +6285,7 @@ static int __init ata_init(void)
rc = ata_sff_init();
if (rc) {
- kfree(ata_force_tbl);
+ ata_free_force_param();
return rc;
}
@@ -6291,7 +6309,7 @@ static void __exit ata_exit(void)
ata_release_transport(ata_scsi_transport_template);
libata_transport_exit();
ata_sff_exit();
- kfree(ata_force_tbl);
+ ata_free_force_param();
}
subsys_initcall(ata_init);
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 6c808cf39135..68cdd81d747c 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -37,7 +37,11 @@ extern int libata_noacpi;
extern int libata_allow_tpm;
extern const struct device_type ata_port_type;
extern struct ata_link *ata_dev_phys_link(struct ata_device *dev);
+#ifdef CONFIG_ATA_FORCE
extern void ata_force_cbl(struct ata_port *ap);
+#else
+static inline void ata_force_cbl(struct ata_port *ap) { }
+#endif
extern u64 ata_tf_to_lba(const struct ata_taskfile *tf);
extern u64 ata_tf_to_lba48(const struct ata_taskfile *tf);
extern struct ata_queued_cmd *ata_qc_new_init(struct ata_device *dev, int tag);
--
2.24.1
Start separating SATA specific code from libata-eh.c:
* move sata_async_notification() to libata-sata.c:
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
16243 18 0 16261 3f85 drivers/ata/libata-eh.o
after:
16164 18 0 16182 3f36 drivers/ata/libata-eh.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-eh.c | 74 --------------------------------------
drivers/ata/libata-sata.c | 75 +++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 2 +-
3 files changed, 76 insertions(+), 75 deletions(-)
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 8dc33b6832f0..ef4d606cd8c6 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1092,80 +1092,6 @@ int ata_port_freeze(struct ata_port *ap)
}
EXPORT_SYMBOL_GPL(ata_port_freeze);
-/**
- * sata_async_notification - SATA async notification handler
- * @ap: ATA port where async notification is received
- *
- * Handler to be called when async notification via SDB FIS is
- * received. This function schedules EH if necessary.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * 1 if EH is scheduled, 0 otherwise.
- */
-int sata_async_notification(struct ata_port *ap)
-{
- u32 sntf;
- int rc;
-
- if (!(ap->flags & ATA_FLAG_AN))
- return 0;
-
- rc = sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf);
- if (rc == 0)
- sata_scr_write(&ap->link, SCR_NOTIFICATION, sntf);
-
- if (!sata_pmp_attached(ap) || rc) {
- /* PMP is not attached or SNTF is not available */
- if (!sata_pmp_attached(ap)) {
- /* PMP is not attached. Check whether ATAPI
- * AN is configured. If so, notify media
- * change.
- */
- struct ata_device *dev = ap->link.device;
-
- if ((dev->class == ATA_DEV_ATAPI) &&
- (dev->flags & ATA_DFLAG_AN))
- ata_scsi_media_change_notify(dev);
- return 0;
- } else {
- /* PMP is attached but SNTF is not available.
- * ATAPI async media change notification is
- * not used. The PMP must be reporting PHY
- * status change, schedule EH.
- */
- ata_port_schedule_eh(ap);
- return 1;
- }
- } else {
- /* PMP is attached and SNTF is available */
- struct ata_link *link;
-
- /* check and notify ATAPI AN */
- ata_for_each_link(link, ap, EDGE) {
- if (!(sntf & (1 << link->pmp)))
- continue;
-
- if ((link->device->class == ATA_DEV_ATAPI) &&
- (link->device->flags & ATA_DFLAG_AN))
- ata_scsi_media_change_notify(link->device);
- }
-
- /* If PMP is reporting that PHY status of some
- * downstream ports has changed, schedule EH.
- */
- if (sntf & (1 << SATA_PMP_CTRL_PORT)) {
- ata_port_schedule_eh(ap);
- return 1;
- }
-
- return 0;
- }
-}
-EXPORT_SYMBOL_GPL(sata_async_notification);
-
/**
* ata_eh_freeze_port - EH helper to freeze port
* @ap: ATA port to freeze
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 2d934ccfc930..008468e516cd 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -4,6 +4,7 @@
*
* Copyright 2003-2004 Red Hat, Inc. All rights reserved.
* Copyright 2003-2004 Jeff Garzik
+ * Copyright 2006 Tejun Heo <[email protected]>
*/
#include <linux/kernel.h>
@@ -1275,3 +1276,77 @@ void ata_sas_free_tag(unsigned int tag, struct ata_port *ap)
{
clear_bit(tag, &ap->sas_tag_allocated);
}
+
+/**
+ * sata_async_notification - SATA async notification handler
+ * @ap: ATA port where async notification is received
+ *
+ * Handler to be called when async notification via SDB FIS is
+ * received. This function schedules EH if necessary.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * 1 if EH is scheduled, 0 otherwise.
+ */
+int sata_async_notification(struct ata_port *ap)
+{
+ u32 sntf;
+ int rc;
+
+ if (!(ap->flags & ATA_FLAG_AN))
+ return 0;
+
+ rc = sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf);
+ if (rc == 0)
+ sata_scr_write(&ap->link, SCR_NOTIFICATION, sntf);
+
+ if (!sata_pmp_attached(ap) || rc) {
+ /* PMP is not attached or SNTF is not available */
+ if (!sata_pmp_attached(ap)) {
+ /* PMP is not attached. Check whether ATAPI
+ * AN is configured. If so, notify media
+ * change.
+ */
+ struct ata_device *dev = ap->link.device;
+
+ if ((dev->class == ATA_DEV_ATAPI) &&
+ (dev->flags & ATA_DFLAG_AN))
+ ata_scsi_media_change_notify(dev);
+ return 0;
+ } else {
+ /* PMP is attached but SNTF is not available.
+ * ATAPI async media change notification is
+ * not used. The PMP must be reporting PHY
+ * status change, schedule EH.
+ */
+ ata_port_schedule_eh(ap);
+ return 1;
+ }
+ } else {
+ /* PMP is attached and SNTF is available */
+ struct ata_link *link;
+
+ /* check and notify ATAPI AN */
+ ata_for_each_link(link, ap, EDGE) {
+ if (!(sntf & (1 << link->pmp)))
+ continue;
+
+ if ((link->device->class == ATA_DEV_ATAPI) &&
+ (link->device->flags & ATA_DFLAG_AN))
+ ata_scsi_media_change_notify(link->device);
+ }
+
+ /* If PMP is reporting that PHY status of some
+ * downstream ports has changed, schedule EH.
+ */
+ if (sntf & (1 << SATA_PMP_CTRL_PORT)) {
+ ata_port_schedule_eh(ap);
+ return 1;
+ }
+
+ return 0;
+ }
+}
+EXPORT_SYMBOL_GPL(sata_async_notification);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 550adfa05cc1..6d6fb25cc650 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1242,6 +1242,7 @@ extern void ata_tf_to_fis(const struct ata_taskfile *tf,
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
extern int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active);
extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
+extern int sata_async_notification(struct ata_port *ap);
extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap);
@@ -1334,7 +1335,6 @@ extern void ata_port_wait_eh(struct ata_port *ap);
extern int ata_link_abort(struct ata_link *link);
extern int ata_port_abort(struct ata_port *ap);
extern int ata_port_freeze(struct ata_port *ap);
-extern int sata_async_notification(struct ata_port *ap);
extern void ata_eh_freeze_port(struct ata_port *ap);
extern void ata_eh_thaw_port(struct ata_port *ap);
--
2.24.1
* move sata_deb_timing_*() to libata-sata.c
* add static inline for sata_ehc_deb_timing() for
CONFIG_SATA_HOST=n case
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
32158 572 40 32770 8002 drivers/ata/libata-core.o
after:
32015 572 40 32627 7f73 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 8 --------
drivers/ata/libata-sata.c | 8 ++++++++
include/linux/libata.h | 31 ++++++++++++++++++-------------
3 files changed, 26 insertions(+), 21 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 2ef0960b2154..20c22dbc1f24 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -65,14 +65,6 @@
#include "libata.h"
#include "libata-transport.h"
-/* debounce timing parameters in msecs { interval, duration, timeout } */
-const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 };
-EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
-const unsigned long sata_deb_timing_hotplug[] = { 25, 500, 2000 };
-EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
-const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 };
-EXPORT_SYMBOL_GPL(sata_deb_timing_long);
-
const struct ata_port_operations ata_base_port_ops = {
.prereset = ata_std_prereset,
.postreset = ata_std_postreset,
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 849582e0d653..f3ad4aca5d09 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -12,6 +12,14 @@
#include "libata.h"
+/* debounce timing parameters in msecs { interval, duration, timeout } */
+const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
+const unsigned long sata_deb_timing_hotplug[] = { 25, 500, 2000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
+const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_long);
+
/**
* sata_scr_valid - test whether SCRs are accessible
* @link: ATA link to test SCR accessibility for
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 8fdfe5e4e6e9..99cd52a5a4c2 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1021,10 +1021,6 @@ struct ata_timing {
/*
* Core layer - drivers/ata/libata-core.c
*/
-extern const unsigned long sata_deb_timing_normal[];
-extern const unsigned long sata_deb_timing_hotplug[];
-extern const unsigned long sata_deb_timing_long[];
-
extern struct ata_port_operations ata_dummy_port_ops;
extern const struct ata_port_info ata_dummy_port_info;
@@ -1062,15 +1058,6 @@ static inline int is_multi_taskfile(struct ata_taskfile *tf)
(tf->command == ATA_CMD_WRITE_MULTI_FUA_EXT);
}
-static inline const unsigned long *
-sata_ehc_deb_timing(struct ata_eh_context *ehc)
-{
- if (ehc->i.flags & ATA_EHI_HOTPLUGGED)
- return sata_deb_timing_hotplug;
- else
- return sata_deb_timing_normal;
-}
-
static inline int ata_port_is_dummy(struct ata_port *ap)
{
return ap->ops == &ata_dummy_port_ops;
@@ -1183,6 +1170,19 @@ extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *
* SATA specific code - drivers/ata/libata-sata.c
*/
#ifdef CONFIG_SATA_HOST
+extern const unsigned long sata_deb_timing_normal[];
+extern const unsigned long sata_deb_timing_hotplug[];
+extern const unsigned long sata_deb_timing_long[];
+
+static inline const unsigned long *
+sata_ehc_deb_timing(struct ata_eh_context *ehc)
+{
+ if (ehc->i.flags & ATA_EHI_HOTPLUGGED)
+ return sata_deb_timing_hotplug;
+ else
+ return sata_deb_timing_normal;
+}
+
extern int sata_scr_valid(struct ata_link *link);
extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
@@ -1194,6 +1194,11 @@ extern int sata_link_hardreset(struct ata_link *link,
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
#else
+static inline const unsigned long *
+sata_ehc_deb_timing(struct ata_eh_context *ehc)
+{
+ return NULL;
+}
static inline int sata_scr_valid(struct ata_link *link) { return 0; }
static inline int sata_scr_read(struct ata_link *link, int reg, u32 *val)
{
--
2.24.1
* move *sata_set_spd*() to libata-sata.c
* add static inlines for CONFIG_SATA_HOST=n case
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
32842 572 40 33458 82ae drivers/ata/libata-core.o
after:
32812 572 40 33428 8290 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 81 ---------------------------------------
drivers/ata/libata-sata.c | 81 +++++++++++++++++++++++++++++++++++++++
drivers/ata/libata.h | 7 ++++
include/linux/libata.h | 3 +-
4 files changed, 90 insertions(+), 82 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index ba1e5c4d3c09..13214ebd0e5c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3050,87 +3050,6 @@ int sata_down_spd_limit(struct ata_link *link, u32 spd_limit)
return 0;
}
-static int __sata_set_spd_needed(struct ata_link *link, u32 *scontrol)
-{
- struct ata_link *host_link = &link->ap->link;
- u32 limit, target, spd;
-
- limit = link->sata_spd_limit;
-
- /* Don't configure downstream link faster than upstream link.
- * It doesn't speed up anything and some PMPs choke on such
- * configuration.
- */
- if (!ata_is_host_link(link) && host_link->sata_spd)
- limit &= (1 << host_link->sata_spd) - 1;
-
- if (limit == UINT_MAX)
- target = 0;
- else
- target = fls(limit);
-
- spd = (*scontrol >> 4) & 0xf;
- *scontrol = (*scontrol & ~0xf0) | ((target & 0xf) << 4);
-
- return spd != target;
-}
-
-/**
- * sata_set_spd_needed - is SATA spd configuration needed
- * @link: Link in question
- *
- * Test whether the spd limit in SControl matches
- * @link->sata_spd_limit. This function is used to determine
- * whether hardreset is necessary to apply SATA spd
- * configuration.
- *
- * LOCKING:
- * Inherited from caller.
- *
- * RETURNS:
- * 1 if SATA spd configuration is needed, 0 otherwise.
- */
-static int sata_set_spd_needed(struct ata_link *link)
-{
- u32 scontrol;
-
- if (sata_scr_read(link, SCR_CONTROL, &scontrol))
- return 1;
-
- return __sata_set_spd_needed(link, &scontrol);
-}
-
-/**
- * sata_set_spd - set SATA spd according to spd limit
- * @link: Link to set SATA spd for
- *
- * Set SATA spd of @link according to sata_spd_limit.
- *
- * LOCKING:
- * Inherited from caller.
- *
- * RETURNS:
- * 0 if spd doesn't need to be changed, 1 if spd has been
- * changed. Negative errno if SCR registers are inaccessible.
- */
-int sata_set_spd(struct ata_link *link)
-{
- u32 scontrol;
- int rc;
-
- if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
- return rc;
-
- if (!__sata_set_spd_needed(link, &scontrol))
- return 0;
-
- if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
- return rc;
-
- return 1;
-}
-EXPORT_SYMBOL_GPL(sata_set_spd);
-
#ifdef CONFIG_ATA_ACPI
/**
* ata_timing_cycle2mode - find xfer mode for the specified cycle duration
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 1ef4c19864ac..d66afdc33d54 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -271,6 +271,87 @@ int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
}
EXPORT_SYMBOL_GPL(sata_link_scr_lpm);
+static int __sata_set_spd_needed(struct ata_link *link, u32 *scontrol)
+{
+ struct ata_link *host_link = &link->ap->link;
+ u32 limit, target, spd;
+
+ limit = link->sata_spd_limit;
+
+ /* Don't configure downstream link faster than upstream link.
+ * It doesn't speed up anything and some PMPs choke on such
+ * configuration.
+ */
+ if (!ata_is_host_link(link) && host_link->sata_spd)
+ limit &= (1 << host_link->sata_spd) - 1;
+
+ if (limit == UINT_MAX)
+ target = 0;
+ else
+ target = fls(limit);
+
+ spd = (*scontrol >> 4) & 0xf;
+ *scontrol = (*scontrol & ~0xf0) | ((target & 0xf) << 4);
+
+ return spd != target;
+}
+
+/**
+ * sata_set_spd_needed - is SATA spd configuration needed
+ * @link: Link in question
+ *
+ * Test whether the spd limit in SControl matches
+ * @link->sata_spd_limit. This function is used to determine
+ * whether hardreset is necessary to apply SATA spd
+ * configuration.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ * RETURNS:
+ * 1 if SATA spd configuration is needed, 0 otherwise.
+ */
+int sata_set_spd_needed(struct ata_link *link)
+{
+ u32 scontrol;
+
+ if (sata_scr_read(link, SCR_CONTROL, &scontrol))
+ return 1;
+
+ return __sata_set_spd_needed(link, &scontrol);
+}
+
+/**
+ * sata_set_spd - set SATA spd according to spd limit
+ * @link: Link to set SATA spd for
+ *
+ * Set SATA spd of @link according to sata_spd_limit.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ * RETURNS:
+ * 0 if spd doesn't need to be changed, 1 if spd has been
+ * changed. Negative errno if SCR registers are inaccessible.
+ */
+int sata_set_spd(struct ata_link *link)
+{
+ u32 scontrol;
+ int rc;
+
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ return rc;
+
+ if (!__sata_set_spd_needed(link, &scontrol))
+ return 0;
+
+ if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
+ return rc;
+
+ return 1;
+}
+EXPORT_SYMBOL_GPL(sata_set_spd);
+
/**
* ata_slave_link_init - initialize slave link
* @ap: port to initialize slave link for
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index cd8090ad43e5..53b45ebe3d55 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -87,6 +87,13 @@ extern unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
#define to_ata_port(d) container_of(d, struct ata_port, tdev)
+/* libata-sata.c */
+#ifdef CONFIG_SATA_HOST
+int sata_set_spd_needed(struct ata_link *link);
+#else
+static inline int sata_set_spd_needed(struct ata_link *link) { return 1; }
+#endif
+
/* libata-acpi.c */
#ifdef CONFIG_ATA_ACPI
extern unsigned int ata_acpi_gtf_filter;
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 372070a9d92e..3f0bdc2c30d3 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1076,7 +1076,6 @@ static inline int ata_port_is_dummy(struct ata_port *ap)
return ap->ops == &ata_dummy_port_ops;
}
-extern int sata_set_spd(struct ata_link *link);
extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
extern int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
@@ -1196,6 +1195,7 @@ extern int sata_scr_valid(struct ata_link *link);
extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
+extern int sata_set_spd(struct ata_link *link);
#else
static inline int sata_scr_valid(struct ata_link *link) { return 0; }
static inline int sata_scr_read(struct ata_link *link, int reg, u32 *val)
@@ -1210,6 +1210,7 @@ static inline int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
{
return -EOPNOTSUPP;
}
+static inline int sata_set_spd(struct ata_link *link) { return -EOPNOTSUPP; }
#endif
extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
bool spm_wakeup);
--
2.24.1
* move sata_link_hardreset() to libata-sata.c
* add static inline for CONFIG_SATA_HOST=n case
* make sata_set_spd_needed() static
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
32724 572 40 33336 8238 drivers/ata/libata-core.o
after:
32559 572 40 33171 8193 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 113 -------------------------------------
drivers/ata/libata-sata.c | 115 +++++++++++++++++++++++++++++++++++++-
drivers/ata/libata.h | 7 ---
include/linux/libata.h | 16 +++++-
4 files changed, 127 insertions(+), 124 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 4ca81ef7c8bd..19624d056d92 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3531,119 +3531,6 @@ int ata_std_prereset(struct ata_link *link, unsigned long deadline)
}
EXPORT_SYMBOL_GPL(ata_std_prereset);
-/**
- * sata_link_hardreset - reset link via SATA phy reset
- * @link: link to reset
- * @timing: timing parameters { interval, duration, timeout } in msec
- * @deadline: deadline jiffies for the operation
- * @online: optional out parameter indicating link onlineness
- * @check_ready: optional callback to check link readiness
- *
- * SATA phy-reset @link using DET bits of SControl register.
- * After hardreset, link readiness is waited upon using
- * ata_wait_ready() if @check_ready is specified. LLDs are
- * allowed to not specify @check_ready and wait itself after this
- * function returns. Device classification is LLD's
- * responsibility.
- *
- * *@online is set to one iff reset succeeded and @link is online
- * after reset.
- *
- * LOCKING:
- * Kernel thread context (may sleep)
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
- unsigned long deadline,
- bool *online, int (*check_ready)(struct ata_link *))
-{
- u32 scontrol;
- int rc;
-
- DPRINTK("ENTER\n");
-
- if (online)
- *online = false;
-
- if (sata_set_spd_needed(link)) {
- /* SATA spec says nothing about how to reconfigure
- * spd. To be on the safe side, turn off phy during
- * reconfiguration. This works for at least ICH7 AHCI
- * and Sil3124.
- */
- if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
- goto out;
-
- scontrol = (scontrol & 0x0f0) | 0x304;
-
- if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
- goto out;
-
- sata_set_spd(link);
- }
-
- /* issue phy wake/reset */
- if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
- goto out;
-
- scontrol = (scontrol & 0x0f0) | 0x301;
-
- if ((rc = sata_scr_write_flush(link, SCR_CONTROL, scontrol)))
- goto out;
-
- /* Couldn't find anything in SATA I/II specs, but AHCI-1.1
- * 10.4.2 says at least 1 ms.
- */
- ata_msleep(link->ap, 1);
-
- /* bring link back */
- rc = sata_link_resume(link, timing, deadline);
- if (rc)
- goto out;
- /* if link is offline nothing more to do */
- if (ata_phys_link_offline(link))
- goto out;
-
- /* Link is online. From this point, -ENODEV too is an error. */
- if (online)
- *online = true;
-
- if (sata_pmp_supported(link->ap) && ata_is_host_link(link)) {
- /* If PMP is supported, we have to do follow-up SRST.
- * Some PMPs don't send D2H Reg FIS after hardreset if
- * the first port is empty. Wait only for
- * ATA_TMOUT_PMP_SRST_WAIT.
- */
- if (check_ready) {
- unsigned long pmp_deadline;
-
- pmp_deadline = ata_deadline(jiffies,
- ATA_TMOUT_PMP_SRST_WAIT);
- if (time_after(pmp_deadline, deadline))
- pmp_deadline = deadline;
- ata_wait_ready(link, pmp_deadline, check_ready);
- }
- rc = -EAGAIN;
- goto out;
- }
-
- rc = 0;
- if (check_ready)
- rc = ata_wait_ready(link, deadline, check_ready);
- out:
- if (rc && rc != -EAGAIN) {
- /* online is set iff link is online && reset succeeded */
- if (online)
- *online = false;
- ata_link_err(link, "COMRESET failed (errno=%d)\n", rc);
- }
- DPRINTK("EXIT, rc=%d\n", rc);
- return rc;
-}
-EXPORT_SYMBOL_GPL(sata_link_hardreset);
-
/**
* sata_std_hardreset - COMRESET w/o waiting or classification
* @link: link to reset
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 34852fced999..05a1872ba329 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -449,7 +449,7 @@ static int __sata_set_spd_needed(struct ata_link *link, u32 *scontrol)
* RETURNS:
* 1 if SATA spd configuration is needed, 0 otherwise.
*/
-int sata_set_spd_needed(struct ata_link *link)
+static int sata_set_spd_needed(struct ata_link *link)
{
u32 scontrol;
@@ -490,6 +490,119 @@ int sata_set_spd(struct ata_link *link)
}
EXPORT_SYMBOL_GPL(sata_set_spd);
+/**
+ * sata_link_hardreset - reset link via SATA phy reset
+ * @link: link to reset
+ * @timing: timing parameters { interval, duration, timeout } in msec
+ * @deadline: deadline jiffies for the operation
+ * @online: optional out parameter indicating link onlineness
+ * @check_ready: optional callback to check link readiness
+ *
+ * SATA phy-reset @link using DET bits of SControl register.
+ * After hardreset, link readiness is waited upon using
+ * ata_wait_ready() if @check_ready is specified. LLDs are
+ * allowed to not specify @check_ready and wait itself after this
+ * function returns. Device classification is LLD's
+ * responsibility.
+ *
+ * *@online is set to one iff reset succeeded and @link is online
+ * after reset.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
+ unsigned long deadline,
+ bool *online, int (*check_ready)(struct ata_link *))
+{
+ u32 scontrol;
+ int rc;
+
+ DPRINTK("ENTER\n");
+
+ if (online)
+ *online = false;
+
+ if (sata_set_spd_needed(link)) {
+ /* SATA spec says nothing about how to reconfigure
+ * spd. To be on the safe side, turn off phy during
+ * reconfiguration. This works for at least ICH7 AHCI
+ * and Sil3124.
+ */
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ goto out;
+
+ scontrol = (scontrol & 0x0f0) | 0x304;
+
+ if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
+ goto out;
+
+ sata_set_spd(link);
+ }
+
+ /* issue phy wake/reset */
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ goto out;
+
+ scontrol = (scontrol & 0x0f0) | 0x301;
+
+ if ((rc = sata_scr_write_flush(link, SCR_CONTROL, scontrol)))
+ goto out;
+
+ /* Couldn't find anything in SATA I/II specs, but AHCI-1.1
+ * 10.4.2 says at least 1 ms.
+ */
+ ata_msleep(link->ap, 1);
+
+ /* bring link back */
+ rc = sata_link_resume(link, timing, deadline);
+ if (rc)
+ goto out;
+ /* if link is offline nothing more to do */
+ if (ata_phys_link_offline(link))
+ goto out;
+
+ /* Link is online. From this point, -ENODEV too is an error. */
+ if (online)
+ *online = true;
+
+ if (sata_pmp_supported(link->ap) && ata_is_host_link(link)) {
+ /* If PMP is supported, we have to do follow-up SRST.
+ * Some PMPs don't send D2H Reg FIS after hardreset if
+ * the first port is empty. Wait only for
+ * ATA_TMOUT_PMP_SRST_WAIT.
+ */
+ if (check_ready) {
+ unsigned long pmp_deadline;
+
+ pmp_deadline = ata_deadline(jiffies,
+ ATA_TMOUT_PMP_SRST_WAIT);
+ if (time_after(pmp_deadline, deadline))
+ pmp_deadline = deadline;
+ ata_wait_ready(link, pmp_deadline, check_ready);
+ }
+ rc = -EAGAIN;
+ goto out;
+ }
+
+ rc = 0;
+ if (check_ready)
+ rc = ata_wait_ready(link, deadline, check_ready);
+ out:
+ if (rc && rc != -EAGAIN) {
+ /* online is set iff link is online && reset succeeded */
+ if (online)
+ *online = false;
+ ata_link_err(link, "COMRESET failed (errno=%d)\n", rc);
+ }
+ DPRINTK("EXIT, rc=%d\n", rc);
+ return rc;
+}
+EXPORT_SYMBOL_GPL(sata_link_hardreset);
+
/**
* ata_slave_link_init - initialize slave link
* @ap: port to initialize slave link for
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index 53b45ebe3d55..cd8090ad43e5 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -87,13 +87,6 @@ extern unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
#define to_ata_port(d) container_of(d, struct ata_port, tdev)
-/* libata-sata.c */
-#ifdef CONFIG_SATA_HOST
-int sata_set_spd_needed(struct ata_link *link);
-#else
-static inline int sata_set_spd_needed(struct ata_link *link) { return 1; }
-#endif
-
/* libata-acpi.c */
#ifdef CONFIG_ATA_ACPI
extern unsigned int ata_acpi_gtf_filter;
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 3981e413f582..bf13af0c47ae 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1079,9 +1079,6 @@ static inline int ata_port_is_dummy(struct ata_port *ap)
extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
extern int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
-extern int sata_link_hardreset(struct ata_link *link,
- const unsigned long *timing, unsigned long deadline,
- bool *online, int (*check_ready)(struct ata_link *));
extern int sata_std_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
extern void ata_std_postreset(struct ata_link *link, unsigned int *classes);
@@ -1192,6 +1189,9 @@ extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
extern int sata_set_spd(struct ata_link *link);
+extern int sata_link_hardreset(struct ata_link *link,
+ const unsigned long *timing, unsigned long deadline,
+ bool *online, int (*check_ready)(struct ata_link *));
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
#else
@@ -1209,6 +1209,16 @@ static inline int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
return -EOPNOTSUPP;
}
static inline int sata_set_spd(struct ata_link *link) { return -EOPNOTSUPP; }
+static inline int sata_link_hardreset(struct ata_link *link,
+ const unsigned long *timing,
+ unsigned long deadline,
+ bool *online,
+ int (*check_ready)(struct ata_link *))
+{
+ if (online)
+ *online = false;
+ return -EOPNOTSUPP;
+}
static inline int sata_link_resume(struct ata_link *link,
const unsigned long *params,
unsigned long deadline)
--
2.24.1
* move ata_qc_complete_multiple() to libata-sata.c
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
32559 572 40 33171 8193 drivers/ata/libata-core.o
after:
32162 572 40 32774 8006 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 59 ---------------------------------------
drivers/ata/libata-sata.c | 59 +++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 2 +-
3 files changed, 60 insertions(+), 60 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 19624d056d92..2ef0960b2154 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4749,65 +4749,6 @@ u64 ata_qc_get_active(struct ata_port *ap)
}
EXPORT_SYMBOL_GPL(ata_qc_get_active);
-/**
- * ata_qc_complete_multiple - Complete multiple qcs successfully
- * @ap: port in question
- * @qc_active: new qc_active mask
- *
- * Complete in-flight commands. This functions is meant to be
- * called from low-level driver's interrupt routine to complete
- * requests normally. ap->qc_active and @qc_active is compared
- * and commands are completed accordingly.
- *
- * Always use this function when completing multiple NCQ commands
- * from IRQ handlers instead of calling ata_qc_complete()
- * multiple times to keep IRQ expect status properly in sync.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * Number of completed commands on success, -errno otherwise.
- */
-int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active)
-{
- u64 done_mask, ap_qc_active = ap->qc_active;
- int nr_done = 0;
-
- /*
- * If the internal tag is set on ap->qc_active, then we care about
- * bit0 on the passed in qc_active mask. Move that bit up to match
- * the internal tag.
- */
- if (ap_qc_active & (1ULL << ATA_TAG_INTERNAL)) {
- qc_active |= (qc_active & 0x01) << ATA_TAG_INTERNAL;
- qc_active ^= qc_active & 0x01;
- }
-
- done_mask = ap_qc_active ^ qc_active;
-
- if (unlikely(done_mask & qc_active)) {
- ata_port_err(ap, "illegal qc_active transition (%08llx->%08llx)\n",
- ap->qc_active, qc_active);
- return -EINVAL;
- }
-
- while (done_mask) {
- struct ata_queued_cmd *qc;
- unsigned int tag = __ffs64(done_mask);
-
- qc = ata_qc_from_tag(ap, tag);
- if (qc) {
- ata_qc_complete(qc);
- nr_done++;
- }
- done_mask &= ~(1ULL << tag);
- }
-
- return nr_done;
-}
-EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
-
/**
* ata_qc_issue - issue taskfile to device
* @qc: command to issue to device
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 05a1872ba329..849582e0d653 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -603,6 +603,65 @@ int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
}
EXPORT_SYMBOL_GPL(sata_link_hardreset);
+/**
+ * ata_qc_complete_multiple - Complete multiple qcs successfully
+ * @ap: port in question
+ * @qc_active: new qc_active mask
+ *
+ * Complete in-flight commands. This functions is meant to be
+ * called from low-level driver's interrupt routine to complete
+ * requests normally. ap->qc_active and @qc_active is compared
+ * and commands are completed accordingly.
+ *
+ * Always use this function when completing multiple NCQ commands
+ * from IRQ handlers instead of calling ata_qc_complete()
+ * multiple times to keep IRQ expect status properly in sync.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ *
+ * RETURNS:
+ * Number of completed commands on success, -errno otherwise.
+ */
+int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active)
+{
+ u64 done_mask, ap_qc_active = ap->qc_active;
+ int nr_done = 0;
+
+ /*
+ * If the internal tag is set on ap->qc_active, then we care about
+ * bit0 on the passed in qc_active mask. Move that bit up to match
+ * the internal tag.
+ */
+ if (ap_qc_active & (1ULL << ATA_TAG_INTERNAL)) {
+ qc_active |= (qc_active & 0x01) << ATA_TAG_INTERNAL;
+ qc_active ^= qc_active & 0x01;
+ }
+
+ done_mask = ap_qc_active ^ qc_active;
+
+ if (unlikely(done_mask & qc_active)) {
+ ata_port_err(ap, "illegal qc_active transition (%08llx->%08llx)\n",
+ ap->qc_active, qc_active);
+ return -EINVAL;
+ }
+
+ while (done_mask) {
+ struct ata_queued_cmd *qc;
+ unsigned int tag = __ffs64(done_mask);
+
+ qc = ata_qc_from_tag(ap, tag);
+ if (qc) {
+ ata_qc_complete(qc);
+ nr_done++;
+ }
+ done_mask &= ~(1ULL << tag);
+ }
+
+ return nr_done;
+}
+EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
+
/**
* ata_slave_link_init - initialize slave link
* @ap: port to initialize slave link for
diff --git a/include/linux/libata.h b/include/linux/libata.h
index bf13af0c47ae..8fdfe5e4e6e9 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1162,7 +1162,6 @@ extern void ata_id_c_string(const u16 *id, unsigned char *s,
extern unsigned int ata_do_dev_read_id(struct ata_device *dev,
struct ata_taskfile *tf, u16 *id);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
-extern int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active);
extern u64 ata_qc_get_active(struct ata_port *ap);
extern void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd);
extern int ata_std_bios_param(struct scsi_device *sdev,
@@ -1234,6 +1233,7 @@ extern int ata_slave_link_init(struct ata_port *ap);
extern void ata_tf_to_fis(const struct ata_taskfile *tf,
u8 pmp, int is_cmd, u8 *fis);
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
+extern int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active);
extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
extern int ata_cable_40wire(struct ata_port *ap);
--
2.24.1
Separate PATA timings code from libata-core.c:
* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) select it
* move following PATA timings code to libata-pata-timings.c:
- ata_timing_quantize()
- ata_timing_merge()
- ata_timing_find_mode()
- ata_timing_compute()
* group above functions together in <linux/libata.h>
* include libata-pata-timings.c in the build when PATA_TIMINGS
config option is enabled
* cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it
depends on code from libata-core.c and libata-pata-timings.c
while its only user is ATA ACPI)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
after:
37820 572 40 38432 9620 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/Kconfig | 21 ++++
drivers/ata/Makefile | 1 +
drivers/ata/libata-core.c | 183 +---------------------------
drivers/ata/libata-pata-timings.c | 192 ++++++++++++++++++++++++++++++
include/linux/libata.h | 16 ++-
5 files changed, 226 insertions(+), 187 deletions(-)
create mode 100644 drivers/ata/libata-pata-timings.c
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ad7760656f71..5b55ebf56b5a 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -37,6 +37,9 @@ config ATA_NONSTANDARD
config SATA_HOST
bool
+config PATA_TIMINGS
+ bool
+
config ATA_VERBOSE_ERROR
bool "Verbose ATA error reporting"
default y
@@ -51,6 +54,7 @@ config ATA_VERBOSE_ERROR
config ATA_ACPI
bool "ATA ACPI Support"
depends on ACPI
+ select PATA_TIMINGS
default y
help
This option adds support for ATA-related ACPI objects.
@@ -341,6 +345,7 @@ config PDC_ADMA
config PATA_OCTEON_CF
tristate "OCTEON Boot Bus Compact Flash support"
depends on CAVIUM_OCTEON_SOC
+ select PATA_TIMINGS
help
This option enables a polled compact flash driver for use with
compact flash cards attached to the OCTEON boot bus.
@@ -536,6 +541,7 @@ comment "PATA SFF controllers with BMDMA"
config PATA_ALI
tristate "ALi PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the ALi ATA interfaces
found on the many ALi chipsets.
@@ -545,6 +551,7 @@ config PATA_ALI
config PATA_AMD
tristate "AMD/NVidia PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the AMD and NVidia PATA
interfaces found on the chipsets for Athlon/Athlon64.
@@ -579,6 +586,7 @@ config PATA_ATIIXP
config PATA_ATP867X
tristate "ARTOP/Acard ATP867X PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for ARTOP/Acard ATP867X PATA
controllers.
@@ -588,6 +596,7 @@ config PATA_ATP867X
config PATA_BK3710
tristate "Palmchip BK3710 PATA support"
depends on ARCH_DAVINCI
+ select PATA_TIMINGS
help
This option enables support for the integrated IDE controller on
the TI DaVinci SoC.
@@ -597,6 +606,7 @@ config PATA_BK3710
config PATA_CMD64X
tristate "CMD64x PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the CMD64x series chips
except for the CMD640.
@@ -642,6 +652,7 @@ config PATA_CS5536
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the Cypress/Contaq CY82C693
chipset found in some Alpha systems
@@ -660,6 +671,7 @@ config PATA_EFAR
config PATA_EP93XX
tristate "Cirrus Logic EP93xx PATA support"
depends on ARCH_EP93XX
+ select PATA_TIMINGS
help
This option enables support for the PATA controller in
the Cirrus Logic EP9312 and EP9315 ARM CPU.
@@ -724,6 +736,7 @@ config PATA_HPT3X3_DMA
config PATA_ICSIDE
tristate "Acorn ICS PATA support"
depends on ARM && ARCH_ACORN
+ select PATA_TIMINGS
help
On Acorn systems, say Y here if you wish to use the ICS PATA
interface card. This is not required for ICS partition support.
@@ -732,6 +745,7 @@ config PATA_ICSIDE
config PATA_IMX
tristate "PATA support for Freescale iMX"
depends on ARCH_MXC
+ select PATA_TIMINGS
help
This option enables support for the PATA host available on Freescale
iMX SoCs.
@@ -817,6 +831,7 @@ config PATA_NINJA32
config PATA_NS87415
tristate "Nat Semi NS87415 PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the National Semiconductor
NS87415 PCI-IDE controller.
@@ -941,6 +956,7 @@ config PATA_TRIFLEX
config PATA_VIA
tristate "VIA PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the VIA PATA interfaces
found on the many VIA chipsets.
@@ -974,6 +990,7 @@ comment "PIO-only SFF controllers"
config PATA_CMD640_PCI
tristate "CMD640 PCI PATA support (Experimental)"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the CMD640 PCI IDE
interface chip. Only the primary channel is currently
@@ -1044,6 +1061,7 @@ config PATA_MPIIX
config PATA_NS87410
tristate "Nat Semi NS87410 PATA support"
depends on PCI
+ select PATA_TIMINGS
help
This option enables support for the National Semiconductor
NS87410 PCI-IDE controller.
@@ -1124,6 +1142,7 @@ config PATA_RZ1000
config PATA_SAMSUNG_CF
tristate "Samsung SoC PATA support"
depends on SAMSUNG_DEV_IDE
+ select PATA_TIMINGS
help
This option enables basic support for Samsung's S3C/S5P board
PATA controllers via the new ATA layer
@@ -1143,6 +1162,7 @@ comment "Generic fallback / legacy drivers"
config PATA_ACPI
tristate "ACPI firmware driver for PATA"
depends on ATA_ACPI && ATA_BMDMA && PCI
+ select PATA_TIMINGS
help
This option enables an ACPI method driver which drives
motherboard PATA controller interfaces through the ACPI
@@ -1162,6 +1182,7 @@ config ATA_GENERIC
config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
depends on (ISA || PCI)
+ select PATA_TIMINGS
help
This option enables support for ISA/VLB/PCI bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index d8cc2e04a6c7..cdaf965fed25 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -127,3 +127,4 @@ libata-$(CONFIG_ATA_SFF) += libata-sff.o
libata-$(CONFIG_SATA_PMP) += libata-pmp.o
libata-$(CONFIG_ATA_ACPI) += libata-acpi.o
libata-$(CONFIG_SATA_ZPODD) += libata-zpodd.o
+libata-$(CONFIG_PATA_TIMINGS) += libata-pata-timings.o
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index acdcedcb3d10..0a56968e2e98 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3204,187 +3204,7 @@ int sata_set_spd(struct ata_link *link)
}
EXPORT_SYMBOL_GPL(sata_set_spd);
-/*
- * This mode timing computation functionality is ported over from
- * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik
- */
-/*
- * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
- * These were taken from ATA/ATAPI-6 standard, rev 0a, except
- * for UDMA6, which is currently supported only by Maxtor drives.
- *
- * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0.
- */
-
-static const struct ata_timing ata_timing[] = {
-/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0, 960, 0 }, */
- { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
- { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
- { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
- { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
- { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
- { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
- { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
-
- { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 50, 960, 0 },
- { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 30, 480, 0 },
- { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 20, 240, 0 },
-
- { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 20, 480, 0 },
- { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 5, 150, 0 },
- { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 5, 120, 0 },
- { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 5, 100, 0 },
- { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 5, 80, 0 },
-
-/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 0, 150 }, */
- { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 0, 120 },
- { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 0, 80 },
- { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 0, 60 },
- { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 0, 45 },
- { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 0, 30 },
- { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 0, 20 },
- { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 0, 15 },
-
- { 0xFF }
-};
-
-#define ENOUGH(v, unit) (((v)-1)/(unit)+1)
-#define EZ(v, unit) ((v)?ENOUGH(((v) * 1000), unit):0)
-
-static void ata_timing_quantize(const struct ata_timing *t,
- struct ata_timing *q, int T, int UT)
-{
- q->setup = EZ(t->setup, T);
- q->act8b = EZ(t->act8b, T);
- q->rec8b = EZ(t->rec8b, T);
- q->cyc8b = EZ(t->cyc8b, T);
- q->active = EZ(t->active, T);
- q->recover = EZ(t->recover, T);
- q->dmack_hold = EZ(t->dmack_hold, T);
- q->cycle = EZ(t->cycle, T);
- q->udma = EZ(t->udma, UT);
-}
-
-void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
- struct ata_timing *m, unsigned int what)
-{
- if (what & ATA_TIMING_SETUP)
- m->setup = max(a->setup, b->setup);
- if (what & ATA_TIMING_ACT8B)
- m->act8b = max(a->act8b, b->act8b);
- if (what & ATA_TIMING_REC8B)
- m->rec8b = max(a->rec8b, b->rec8b);
- if (what & ATA_TIMING_CYC8B)
- m->cyc8b = max(a->cyc8b, b->cyc8b);
- if (what & ATA_TIMING_ACTIVE)
- m->active = max(a->active, b->active);
- if (what & ATA_TIMING_RECOVER)
- m->recover = max(a->recover, b->recover);
- if (what & ATA_TIMING_DMACK_HOLD)
- m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
- if (what & ATA_TIMING_CYCLE)
- m->cycle = max(a->cycle, b->cycle);
- if (what & ATA_TIMING_UDMA)
- m->udma = max(a->udma, b->udma);
-}
-EXPORT_SYMBOL_GPL(ata_timing_merge);
-
-const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
-{
- const struct ata_timing *t = ata_timing;
-
- while (xfer_mode > t->mode)
- t++;
-
- if (xfer_mode == t->mode)
- return t;
-
- WARN_ONCE(true, "%s: unable to find timing for xfer_mode 0x%x\n",
- __func__, xfer_mode);
-
- return NULL;
-}
-EXPORT_SYMBOL_GPL(ata_timing_find_mode);
-
-int ata_timing_compute(struct ata_device *adev, unsigned short speed,
- struct ata_timing *t, int T, int UT)
-{
- const u16 *id = adev->id;
- const struct ata_timing *s;
- struct ata_timing p;
-
- /*
- * Find the mode.
- */
- s = ata_timing_find_mode(speed);
- if (!s)
- return -EINVAL;
-
- memcpy(t, s, sizeof(*s));
-
- /*
- * If the drive is an EIDE drive, it can tell us it needs extended
- * PIO/MW_DMA cycle timing.
- */
-
- if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
- memset(&p, 0, sizeof(p));
-
- if (speed >= XFER_PIO_0 && speed < XFER_SW_DMA_0) {
- if (speed <= XFER_PIO_2)
- p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
- else if ((speed <= XFER_PIO_4) ||
- (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
- p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
- } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
- p.cycle = id[ATA_ID_EIDE_DMA_MIN];
-
- ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
- }
-
- /*
- * Convert the timing to bus clock counts.
- */
-
- ata_timing_quantize(t, t, T, UT);
-
- /*
- * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
- * S.M.A.R.T * and some other commands. We have to ensure that the
- * DMA cycle timing is slower/equal than the fastest PIO timing.
- */
-
- if (speed > XFER_PIO_6) {
- ata_timing_compute(adev, adev->pio_mode, &p, T, UT);
- ata_timing_merge(&p, t, t, ATA_TIMING_ALL);
- }
-
- /*
- * Lengthen active & recovery time so that cycle time is correct.
- */
-
- if (t->act8b + t->rec8b < t->cyc8b) {
- t->act8b += (t->cyc8b - (t->act8b + t->rec8b)) / 2;
- t->rec8b = t->cyc8b - t->act8b;
- }
-
- if (t->active + t->recover < t->cycle) {
- t->active += (t->cycle - (t->active + t->recover)) / 2;
- t->recover = t->cycle - t->active;
- }
-
- /*
- * In a few cases quantisation may produce enough errors to
- * leave t->cycle too low for the sum of active and recovery
- * if so we must correct this.
- */
- if (t->active + t->recover > t->cycle)
- t->cycle = t->active + t->recover;
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(ata_timing_compute);
-
+#ifdef CONFIG_ATA_ACPI
/**
* ata_timing_cycle2mode - find xfer mode for the specified cycle duration
* @xfer_shift: ATA_SHIFT_* value for transfer type to examine.
@@ -3435,6 +3255,7 @@ u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle)
return last_mode;
}
+#endif
/**
* ata_down_xfermask_limit - adjust dev xfer masks downward
diff --git a/drivers/ata/libata-pata-timings.c b/drivers/ata/libata-pata-timings.c
new file mode 100644
index 000000000000..af341226cc64
--- /dev/null
+++ b/drivers/ata/libata-pata-timings.c
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Helper library for PATA timings
+ *
+ * Copyright 2003-2004 Red Hat, Inc. All rights reserved.
+ * Copyright 2003-2004 Jeff Garzik
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/libata.h>
+
+/*
+ * This mode timing computation functionality is ported over from
+ * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik
+ */
+/*
+ * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
+ * These were taken from ATA/ATAPI-6 standard, rev 0a, except
+ * for UDMA6, which is currently supported only by Maxtor drives.
+ *
+ * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0.
+ */
+
+static const struct ata_timing ata_timing[] = {
+/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0, 960, 0 }, */
+ { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
+ { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
+ { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
+ { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
+ { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
+ { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
+ { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
+
+ { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 50, 960, 0 },
+ { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 30, 480, 0 },
+ { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 20, 240, 0 },
+
+ { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 20, 480, 0 },
+ { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 5, 150, 0 },
+ { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 5, 120, 0 },
+ { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 5, 100, 0 },
+ { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 5, 80, 0 },
+
+/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 0, 150 }, */
+ { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 0, 120 },
+ { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 0, 80 },
+ { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 0, 60 },
+ { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 0, 45 },
+ { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 0, 30 },
+ { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 0, 20 },
+ { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 0, 15 },
+
+ { 0xFF }
+};
+
+#define ENOUGH(v, unit) (((v)-1)/(unit)+1)
+#define EZ(v, unit) ((v)?ENOUGH(((v) * 1000), unit):0)
+
+static void ata_timing_quantize(const struct ata_timing *t,
+ struct ata_timing *q, int T, int UT)
+{
+ q->setup = EZ(t->setup, T);
+ q->act8b = EZ(t->act8b, T);
+ q->rec8b = EZ(t->rec8b, T);
+ q->cyc8b = EZ(t->cyc8b, T);
+ q->active = EZ(t->active, T);
+ q->recover = EZ(t->recover, T);
+ q->dmack_hold = EZ(t->dmack_hold, T);
+ q->cycle = EZ(t->cycle, T);
+ q->udma = EZ(t->udma, UT);
+}
+
+void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
+ struct ata_timing *m, unsigned int what)
+{
+ if (what & ATA_TIMING_SETUP)
+ m->setup = max(a->setup, b->setup);
+ if (what & ATA_TIMING_ACT8B)
+ m->act8b = max(a->act8b, b->act8b);
+ if (what & ATA_TIMING_REC8B)
+ m->rec8b = max(a->rec8b, b->rec8b);
+ if (what & ATA_TIMING_CYC8B)
+ m->cyc8b = max(a->cyc8b, b->cyc8b);
+ if (what & ATA_TIMING_ACTIVE)
+ m->active = max(a->active, b->active);
+ if (what & ATA_TIMING_RECOVER)
+ m->recover = max(a->recover, b->recover);
+ if (what & ATA_TIMING_DMACK_HOLD)
+ m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
+ if (what & ATA_TIMING_CYCLE)
+ m->cycle = max(a->cycle, b->cycle);
+ if (what & ATA_TIMING_UDMA)
+ m->udma = max(a->udma, b->udma);
+}
+EXPORT_SYMBOL_GPL(ata_timing_merge);
+
+const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
+{
+ const struct ata_timing *t = ata_timing;
+
+ while (xfer_mode > t->mode)
+ t++;
+
+ if (xfer_mode == t->mode)
+ return t;
+
+ WARN_ONCE(true, "%s: unable to find timing for xfer_mode 0x%x\n",
+ __func__, xfer_mode);
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(ata_timing_find_mode);
+
+int ata_timing_compute(struct ata_device *adev, unsigned short speed,
+ struct ata_timing *t, int T, int UT)
+{
+ const u16 *id = adev->id;
+ const struct ata_timing *s;
+ struct ata_timing p;
+
+ /*
+ * Find the mode.
+ */
+ s = ata_timing_find_mode(speed);
+ if (!s)
+ return -EINVAL;
+
+ memcpy(t, s, sizeof(*s));
+
+ /*
+ * If the drive is an EIDE drive, it can tell us it needs extended
+ * PIO/MW_DMA cycle timing.
+ */
+
+ if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
+ memset(&p, 0, sizeof(p));
+
+ if (speed >= XFER_PIO_0 && speed < XFER_SW_DMA_0) {
+ if (speed <= XFER_PIO_2)
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
+ else if ((speed <= XFER_PIO_4) ||
+ (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
+ } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ p.cycle = id[ATA_ID_EIDE_DMA_MIN];
+
+ ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
+ }
+
+ /*
+ * Convert the timing to bus clock counts.
+ */
+
+ ata_timing_quantize(t, t, T, UT);
+
+ /*
+ * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
+ * S.M.A.R.T * and some other commands. We have to ensure that the
+ * DMA cycle timing is slower/equal than the fastest PIO timing.
+ */
+
+ if (speed > XFER_PIO_6) {
+ ata_timing_compute(adev, adev->pio_mode, &p, T, UT);
+ ata_timing_merge(&p, t, t, ATA_TIMING_ALL);
+ }
+
+ /*
+ * Lengthen active & recovery time so that cycle time is correct.
+ */
+
+ if (t->act8b + t->rec8b < t->cyc8b) {
+ t->act8b += (t->cyc8b - (t->act8b + t->rec8b)) / 2;
+ t->rec8b = t->cyc8b - t->act8b;
+ }
+
+ if (t->active + t->recover < t->cycle) {
+ t->active += (t->cycle - (t->active + t->recover)) / 2;
+ t->recover = t->cycle - t->active;
+ }
+
+ /*
+ * In a few cases quantisation may produce enough errors to
+ * leave t->cycle too low for the sum of active and recovery
+ * if so we must correct this.
+ */
+ if (t->active + t->recover > t->cycle)
+ t->cycle = t->active + t->recover;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_timing_compute);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index df7c1b538bb1..6c4f4fe26edb 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1207,12 +1207,6 @@ extern int ata_cable_unknown(struct ata_port *ap);
/* Timing helpers */
extern unsigned int ata_pio_need_iordy(const struct ata_device *);
-extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
-extern int ata_timing_compute(struct ata_device *, unsigned short,
- struct ata_timing *, int, int);
-extern void ata_timing_merge(const struct ata_timing *,
- const struct ata_timing *, struct ata_timing *,
- unsigned int);
extern u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle);
/* PCI */
@@ -1806,6 +1800,16 @@ static inline int ata_dma_enabled(struct ata_device *adev)
return (adev->dma_mode == 0xFF ? 0 : 1);
}
+/**************************************************************************
+ * PATA timings - drivers/ata/libata-pata-timings.c
+ */
+extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
+extern int ata_timing_compute(struct ata_device *, unsigned short,
+ struct ata_timing *, int, int);
+extern void ata_timing_merge(const struct ata_timing *,
+ const struct ata_timing *, struct ata_timing *,
+ unsigned int);
+
/**************************************************************************
* PMP - drivers/ata/libata-pmp.c
*/
--
2.24.1
When CONFIG_SATA_HOST=n there are no NCQ capable host drivers
built so it is safe to hardwire ata_ncq_enabled() to always
return zero.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37820 572 40 38432 9620 drivers/ata/libata-core.o
21040 105 576 21721 54d9 drivers/ata/libata-scsi.o
17405 18 0 17423 440f drivers/ata/libata-eh.o
after:
37582 572 40 38194 9532 drivers/ata/libata-core.o
20702 105 576 21383 5387 drivers/ata/libata-scsi.o
17353 18 0 17371 43db drivers/ata/libata-eh.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
include/linux/libata.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 6c4f4fe26edb..ce361b15559b 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1632,6 +1632,8 @@ extern struct ata_device *ata_dev_next(struct ata_device *dev,
*/
static inline int ata_ncq_enabled(struct ata_device *dev)
{
+ if (!IS_ENABLED(CONFIG_SATA_HOST))
+ return 0;
return (dev->flags & (ATA_DFLAG_PIO | ATA_DFLAG_NCQ_OFF |
ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ;
}
--
2.24.1
* un-inline:
- ata_scsi_dump_cdb()
- __ata_scsi_queuecmd()
* un-static:
- ata_scsi_sdev_config()
- ata_scsi_dev_config()
- ata_scsi_dump_cdb()
- __ata_scsi_queuecmd()
* move ata_sas_*() to libata-sata.c:
* add static inlines for CONFIG_SATA_HOST=n case for
ata_sas_{allocate,free}_tag()
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
19137 23 576 19736 4d18 drivers/ata/libata-scsi.o
after:
18330 23 576 18929 49f1 drivers/ata/libata-scsi.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-sata.c | 213 ++++++++++++++++++++++++++++++++++++
drivers/ata/libata-scsi.c | 222 +-------------------------------------
drivers/ata/libata.h | 19 +++-
include/linux/libata.h | 24 ++---
4 files changed, 245 insertions(+), 233 deletions(-)
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 341699f5af20..2d934ccfc930 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -8,10 +8,12 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <linux/libata.h>
#include "libata.h"
+#include "libata-transport.h"
/* debounce timing parameters in msecs { interval, duration, timeout } */
const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 };
@@ -1062,3 +1064,214 @@ int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
return __ata_change_queue_depth(ap, sdev, queue_depth);
}
EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
+
+/**
+ * port_alloc - Allocate port for a SAS attached SATA device
+ * @host: ATA host container for all SAS ports
+ * @port_info: Information from low-level host driver
+ * @shost: SCSI host that the scsi device is attached to
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * ata_port pointer on success / NULL on failure.
+ */
+
+struct ata_port *ata_sas_port_alloc(struct ata_host *host,
+ struct ata_port_info *port_info,
+ struct Scsi_Host *shost)
+{
+ struct ata_port *ap;
+
+ ap = ata_port_alloc(host);
+ if (!ap)
+ return NULL;
+
+ ap->port_no = 0;
+ ap->lock = &host->lock;
+ ap->pio_mask = port_info->pio_mask;
+ ap->mwdma_mask = port_info->mwdma_mask;
+ ap->udma_mask = port_info->udma_mask;
+ ap->flags |= port_info->flags;
+ ap->ops = port_info->port_ops;
+ ap->cbl = ATA_CBL_SATA;
+
+ return ap;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_alloc);
+
+/**
+ * ata_sas_port_start - Set port up for dma.
+ * @ap: Port to initialize
+ *
+ * Called just after data structures for each port are
+ * initialized.
+ *
+ * May be used as the port_start() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+int ata_sas_port_start(struct ata_port *ap)
+{
+ /*
+ * the port is marked as frozen at allocation time, but if we don't
+ * have new eh, we won't thaw it
+ */
+ if (!ap->ops->error_handler)
+ ap->pflags &= ~ATA_PFLAG_FROZEN;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_start);
+
+/**
+ * ata_port_stop - Undo ata_sas_port_start()
+ * @ap: Port to shut down
+ *
+ * May be used as the port_stop() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
+void ata_sas_port_stop(struct ata_port *ap)
+{
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_stop);
+
+/**
+ * ata_sas_async_probe - simply schedule probing and return
+ * @ap: Port to probe
+ *
+ * For batch scheduling of probe for sas attached ata devices, assumes
+ * the port has already been through ata_sas_port_init()
+ */
+void ata_sas_async_probe(struct ata_port *ap)
+{
+ __ata_port_probe(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_async_probe);
+
+int ata_sas_sync_probe(struct ata_port *ap)
+{
+ return ata_port_probe(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_sync_probe);
+
+
+/**
+ * ata_sas_port_init - Initialize a SATA device
+ * @ap: SATA port to initialize
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * Zero on success, non-zero on error.
+ */
+
+int ata_sas_port_init(struct ata_port *ap)
+{
+ int rc = ap->ops->port_start(ap);
+
+ if (rc)
+ return rc;
+ ap->print_id = atomic_inc_return(&ata_print_id);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_init);
+
+int ata_sas_tport_add(struct device *parent, struct ata_port *ap)
+{
+ return ata_tport_add(parent, ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_tport_add);
+
+void ata_sas_tport_delete(struct ata_port *ap)
+{
+ ata_tport_delete(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_tport_delete);
+
+/**
+ * ata_sas_port_destroy - Destroy a SATA port allocated by ata_sas_port_alloc
+ * @ap: SATA port to destroy
+ *
+ */
+
+void ata_sas_port_destroy(struct ata_port *ap)
+{
+ if (ap->ops->port_stop)
+ ap->ops->port_stop(ap);
+ kfree(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_destroy);
+
+/**
+ * ata_sas_slave_configure - Default slave_config routine for libata devices
+ * @sdev: SCSI device to configure
+ * @ap: ATA port to which SCSI device is attached
+ *
+ * RETURNS:
+ * Zero.
+ */
+
+int ata_sas_slave_configure(struct scsi_device *sdev, struct ata_port *ap)
+{
+ ata_scsi_sdev_config(sdev);
+ ata_scsi_dev_config(sdev, ap->link.device);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_slave_configure);
+
+/**
+ * ata_sas_queuecmd - Issue SCSI cdb to libata-managed device
+ * @cmd: SCSI command to be sent
+ * @ap: ATA port to which the command is being sent
+ *
+ * RETURNS:
+ * Return value from __ata_scsi_queuecmd() if @cmd can be queued,
+ * 0 otherwise.
+ */
+
+int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap)
+{
+ int rc = 0;
+
+ ata_scsi_dump_cdb(ap, cmd);
+
+ if (likely(ata_dev_enabled(ap->link.device)))
+ rc = __ata_scsi_queuecmd(cmd, ap->link.device);
+ else {
+ cmd->result = (DID_BAD_TARGET << 16);
+ cmd->scsi_done(cmd);
+ }
+ return rc;
+}
+EXPORT_SYMBOL_GPL(ata_sas_queuecmd);
+
+int ata_sas_allocate_tag(struct ata_port *ap)
+{
+ unsigned int max_queue = ap->host->n_tags;
+ unsigned int i, tag;
+
+ for (i = 0, tag = ap->sas_last_tag + 1; i < max_queue; i++, tag++) {
+ tag = tag < max_queue ? tag : 0;
+
+ /* the last tag is reserved for internal command. */
+ if (ata_tag_internal(tag))
+ continue;
+
+ if (!test_and_set_bit(tag, &ap->sas_tag_allocated)) {
+ ap->sas_last_tag = tag;
+ return tag;
+ }
+ }
+ return -1;
+}
+
+void ata_sas_free_tag(unsigned int tag, struct ata_port *ap)
+{
+ clear_bit(tag, &ap->sas_tag_allocated);
+}
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 6d295d0396d0..08d40dce7200 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -987,7 +987,7 @@ static void ata_gen_ata_sense(struct ata_queued_cmd *qc)
scsi_set_sense_information(sb, SCSI_SENSE_BUFFERSIZE, block);
}
-static void ata_scsi_sdev_config(struct scsi_device *sdev)
+void ata_scsi_sdev_config(struct scsi_device *sdev)
{
sdev->use_10_for_rw = 1;
sdev->use_10_for_ms = 1;
@@ -1027,8 +1027,7 @@ static int atapi_drain_needed(struct request *rq)
return atapi_cmd_type(scsi_req(rq)->cmd[0]) == ATAPI_MISC;
}
-static int ata_scsi_dev_config(struct scsi_device *sdev,
- struct ata_device *dev)
+int ata_scsi_dev_config(struct scsi_device *sdev, struct ata_device *dev)
{
struct request_queue *q = sdev->request_queue;
@@ -4004,8 +4003,7 @@ static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd)
* Prints the contents of a SCSI command via printk().
*/
-static inline void ata_scsi_dump_cdb(struct ata_port *ap,
- struct scsi_cmnd *cmd)
+void ata_scsi_dump_cdb(struct ata_port *ap, struct scsi_cmnd *cmd)
{
#ifdef ATA_VERBOSE_DEBUG
struct scsi_device *scsidev = cmd->device;
@@ -4017,8 +4015,7 @@ static inline void ata_scsi_dump_cdb(struct ata_port *ap,
#endif
}
-static inline int __ata_scsi_queuecmd(struct scsi_cmnd *scmd,
- struct ata_device *dev)
+int __ata_scsi_queuecmd(struct scsi_cmnd *scmd, struct ata_device *dev)
{
u8 scsi_op = scmd->cmnd[0];
ata_xlat_func_t xlat_func;
@@ -4635,214 +4632,3 @@ void ata_scsi_dev_rescan(struct work_struct *work)
spin_unlock_irqrestore(ap->lock, flags);
mutex_unlock(&ap->scsi_scan_mutex);
}
-
-/**
- * ata_sas_port_alloc - Allocate port for a SAS attached SATA device
- * @host: ATA host container for all SAS ports
- * @port_info: Information from low-level host driver
- * @shost: SCSI host that the scsi device is attached to
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- * RETURNS:
- * ata_port pointer on success / NULL on failure.
- */
-
-struct ata_port *ata_sas_port_alloc(struct ata_host *host,
- struct ata_port_info *port_info,
- struct Scsi_Host *shost)
-{
- struct ata_port *ap;
-
- ap = ata_port_alloc(host);
- if (!ap)
- return NULL;
-
- ap->port_no = 0;
- ap->lock = &host->lock;
- ap->pio_mask = port_info->pio_mask;
- ap->mwdma_mask = port_info->mwdma_mask;
- ap->udma_mask = port_info->udma_mask;
- ap->flags |= port_info->flags;
- ap->ops = port_info->port_ops;
- ap->cbl = ATA_CBL_SATA;
-
- return ap;
-}
-EXPORT_SYMBOL_GPL(ata_sas_port_alloc);
-
-/**
- * ata_sas_port_start - Set port up for dma.
- * @ap: Port to initialize
- *
- * Called just after data structures for each port are
- * initialized.
- *
- * May be used as the port_start() entry in ata_port_operations.
- *
- * LOCKING:
- * Inherited from caller.
- */
-int ata_sas_port_start(struct ata_port *ap)
-{
- /*
- * the port is marked as frozen at allocation time, but if we don't
- * have new eh, we won't thaw it
- */
- if (!ap->ops->error_handler)
- ap->pflags &= ~ATA_PFLAG_FROZEN;
- return 0;
-}
-EXPORT_SYMBOL_GPL(ata_sas_port_start);
-
-/**
- * ata_port_stop - Undo ata_sas_port_start()
- * @ap: Port to shut down
- *
- * May be used as the port_stop() entry in ata_port_operations.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-void ata_sas_port_stop(struct ata_port *ap)
-{
-}
-EXPORT_SYMBOL_GPL(ata_sas_port_stop);
-
-/**
- * ata_sas_async_probe - simply schedule probing and return
- * @ap: Port to probe
- *
- * For batch scheduling of probe for sas attached ata devices, assumes
- * the port has already been through ata_sas_port_init()
- */
-void ata_sas_async_probe(struct ata_port *ap)
-{
- __ata_port_probe(ap);
-}
-EXPORT_SYMBOL_GPL(ata_sas_async_probe);
-
-int ata_sas_sync_probe(struct ata_port *ap)
-{
- return ata_port_probe(ap);
-}
-EXPORT_SYMBOL_GPL(ata_sas_sync_probe);
-
-
-/**
- * ata_sas_port_init - Initialize a SATA device
- * @ap: SATA port to initialize
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- * RETURNS:
- * Zero on success, non-zero on error.
- */
-
-int ata_sas_port_init(struct ata_port *ap)
-{
- int rc = ap->ops->port_start(ap);
-
- if (rc)
- return rc;
- ap->print_id = atomic_inc_return(&ata_print_id);
- return 0;
-}
-EXPORT_SYMBOL_GPL(ata_sas_port_init);
-
-int ata_sas_tport_add(struct device *parent, struct ata_port *ap)
-{
- return ata_tport_add(parent, ap);
-}
-EXPORT_SYMBOL_GPL(ata_sas_tport_add);
-
-void ata_sas_tport_delete(struct ata_port *ap)
-{
- ata_tport_delete(ap);
-}
-EXPORT_SYMBOL_GPL(ata_sas_tport_delete);
-
-/**
- * ata_sas_port_destroy - Destroy a SATA port allocated by ata_sas_port_alloc
- * @ap: SATA port to destroy
- *
- */
-
-void ata_sas_port_destroy(struct ata_port *ap)
-{
- if (ap->ops->port_stop)
- ap->ops->port_stop(ap);
- kfree(ap);
-}
-EXPORT_SYMBOL_GPL(ata_sas_port_destroy);
-
-/**
- * ata_sas_slave_configure - Default slave_config routine for libata devices
- * @sdev: SCSI device to configure
- * @ap: ATA port to which SCSI device is attached
- *
- * RETURNS:
- * Zero.
- */
-
-int ata_sas_slave_configure(struct scsi_device *sdev, struct ata_port *ap)
-{
- ata_scsi_sdev_config(sdev);
- ata_scsi_dev_config(sdev, ap->link.device);
- return 0;
-}
-EXPORT_SYMBOL_GPL(ata_sas_slave_configure);
-
-/**
- * ata_sas_queuecmd - Issue SCSI cdb to libata-managed device
- * @cmd: SCSI command to be sent
- * @ap: ATA port to which the command is being sent
- *
- * RETURNS:
- * Return value from __ata_scsi_queuecmd() if @cmd can be queued,
- * 0 otherwise.
- */
-
-int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap)
-{
- int rc = 0;
-
- ata_scsi_dump_cdb(ap, cmd);
-
- if (likely(ata_dev_enabled(ap->link.device)))
- rc = __ata_scsi_queuecmd(cmd, ap->link.device);
- else {
- cmd->result = (DID_BAD_TARGET << 16);
- cmd->scsi_done(cmd);
- }
- return rc;
-}
-EXPORT_SYMBOL_GPL(ata_sas_queuecmd);
-
-int ata_sas_allocate_tag(struct ata_port *ap)
-{
- unsigned int max_queue = ap->host->n_tags;
- unsigned int i, tag;
-
- for (i = 0, tag = ap->sas_last_tag + 1; i < max_queue; i++, tag++) {
- tag = tag < max_queue ? tag : 0;
-
- /* the last tag is reserved for internal command. */
- if (ata_tag_internal(tag))
- continue;
-
- if (!test_and_set_bit(tag, &ap->sas_tag_allocated)) {
- ap->sas_last_tag = tag;
- return tag;
- }
- }
- return -1;
-}
-
-void ata_sas_free_tag(unsigned int tag, struct ata_port *ap)
-{
- clear_bit(tag, &ap->sas_tag_allocated);
-}
diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
index ce3f3c039572..6c808cf39135 100644
--- a/drivers/ata/libata.h
+++ b/drivers/ata/libata.h
@@ -87,6 +87,18 @@ extern unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
#define to_ata_port(d) container_of(d, struct ata_port, tdev)
+/* libata-sata.c */
+#ifdef CONFIG_SATA_HOST
+int ata_sas_allocate_tag(struct ata_port *ap);
+void ata_sas_free_tag(unsigned int tag, struct ata_port *ap);
+#else
+static inline int ata_sas_allocate_tag(struct ata_port *ap)
+{
+ return -EOPNOTSUPP;
+}
+static inline void ata_sas_free_tag(unsigned int tag, struct ata_port *ap) { }
+#endif
+
/* libata-acpi.c */
#ifdef CONFIG_ATA_ACPI
extern unsigned int ata_acpi_gtf_filter;
@@ -130,9 +142,10 @@ extern void ata_scsi_dev_rescan(struct work_struct *work);
extern int ata_bus_probe(struct ata_port *ap);
extern int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel,
unsigned int id, u64 lun);
-int ata_sas_allocate_tag(struct ata_port *ap);
-void ata_sas_free_tag(unsigned int tag, struct ata_port *ap);
-
+void ata_scsi_sdev_config(struct scsi_device *sdev);
+int ata_scsi_dev_config(struct scsi_device *sdev, struct ata_device *dev);
+void ata_scsi_dump_cdb(struct ata_port *ap, struct scsi_cmnd *cmd);
+int __ata_scsi_queuecmd(struct scsi_cmnd *scmd, struct ata_device *dev);
/* libata-eh.c */
extern unsigned long ata_internal_cmd_timeout(struct ata_device *dev, u8 cmd);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 08c4c365fd98..550adfa05cc1 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1096,18 +1096,6 @@ extern int ata_scsi_ioctl(struct scsi_device *dev, unsigned int cmd,
extern int ata_scsi_queuecmd(struct Scsi_Host *h, struct scsi_cmnd *cmd);
extern int ata_sas_scsi_ioctl(struct ata_port *ap, struct scsi_device *dev,
unsigned int cmd, void __user *arg);
-extern void ata_sas_port_destroy(struct ata_port *);
-extern struct ata_port *ata_sas_port_alloc(struct ata_host *,
- struct ata_port_info *, struct Scsi_Host *);
-extern void ata_sas_async_probe(struct ata_port *ap);
-extern int ata_sas_sync_probe(struct ata_port *ap);
-extern int ata_sas_port_init(struct ata_port *);
-extern int ata_sas_port_start(struct ata_port *ap);
-extern int ata_sas_tport_add(struct device *parent, struct ata_port *ap);
-extern void ata_sas_tport_delete(struct ata_port *ap);
-extern void ata_sas_port_stop(struct ata_port *ap);
-extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
-extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap);
extern bool ata_link_online(struct ata_link *link);
extern bool ata_link_offline(struct ata_link *link);
#ifdef CONFIG_PM
@@ -1237,6 +1225,18 @@ extern int sata_link_debounce(struct ata_link *link,
extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
bool spm_wakeup);
extern int ata_slave_link_init(struct ata_port *ap);
+extern void ata_sas_port_destroy(struct ata_port *);
+extern struct ata_port *ata_sas_port_alloc(struct ata_host *,
+ struct ata_port_info *, struct Scsi_Host *);
+extern void ata_sas_async_probe(struct ata_port *ap);
+extern int ata_sas_sync_probe(struct ata_port *ap);
+extern int ata_sas_port_init(struct ata_port *);
+extern int ata_sas_port_start(struct ata_port *ap);
+extern int ata_sas_tport_add(struct device *parent, struct ata_port *ap);
+extern void ata_sas_tport_delete(struct ata_port *ap);
+extern void ata_sas_port_stop(struct ata_port *ap);
+extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
+extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap);
extern void ata_tf_to_fis(const struct ata_taskfile *tf,
u8 pmp, int is_cmd, u8 *fis);
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
--
2.24.1
* move sata_scr_*() to libata-sata.c
* add static inlines for CONFIG_SATA_HOST=n case
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
35642 572 40 36254 8d9e drivers/ata/libata-core.o
16607 18 0 16625 40f1 drivers/ata/libata-eh.o
after:
32846 572 40 33458 82b2 drivers/ata/libata-core.o
16243 18 0 16261 3f85 drivers/ata/libata-eh.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 109 --------------------------------------
drivers/ata/libata-sata.c | 109 ++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 24 +++++++--
3 files changed, 129 insertions(+), 113 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index b4a952dce7ab..ba1e5c4d3c09 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -5215,115 +5215,6 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
ata_qc_complete(qc);
}
-/**
- * sata_scr_valid - test whether SCRs are accessible
- * @link: ATA link to test SCR accessibility for
- *
- * Test whether SCRs are accessible for @link.
- *
- * LOCKING:
- * None.
- *
- * RETURNS:
- * 1 if SCRs are accessible, 0 otherwise.
- */
-int sata_scr_valid(struct ata_link *link)
-{
- struct ata_port *ap = link->ap;
-
- return (ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read;
-}
-EXPORT_SYMBOL_GPL(sata_scr_valid);
-
-/**
- * sata_scr_read - read SCR register of the specified port
- * @link: ATA link to read SCR for
- * @reg: SCR to read
- * @val: Place to store read value
- *
- * Read SCR register @reg of @link into *@val. This function is
- * guaranteed to succeed if @link is ap->link, the cable type of
- * the port is SATA and the port implements ->scr_read.
- *
- * LOCKING:
- * None if @link is ap->link. Kernel thread context otherwise.
- *
- * RETURNS:
- * 0 on success, negative errno on failure.
- */
-int sata_scr_read(struct ata_link *link, int reg, u32 *val)
-{
- if (ata_is_host_link(link)) {
- if (sata_scr_valid(link))
- return link->ap->ops->scr_read(link, reg, val);
- return -EOPNOTSUPP;
- }
-
- return sata_pmp_scr_read(link, reg, val);
-}
-EXPORT_SYMBOL_GPL(sata_scr_read);
-
-/**
- * sata_scr_write - write SCR register of the specified port
- * @link: ATA link to write SCR for
- * @reg: SCR to write
- * @val: value to write
- *
- * Write @val to SCR register @reg of @link. This function is
- * guaranteed to succeed if @link is ap->link, the cable type of
- * the port is SATA and the port implements ->scr_read.
- *
- * LOCKING:
- * None if @link is ap->link. Kernel thread context otherwise.
- *
- * RETURNS:
- * 0 on success, negative errno on failure.
- */
-int sata_scr_write(struct ata_link *link, int reg, u32 val)
-{
- if (ata_is_host_link(link)) {
- if (sata_scr_valid(link))
- return link->ap->ops->scr_write(link, reg, val);
- return -EOPNOTSUPP;
- }
-
- return sata_pmp_scr_write(link, reg, val);
-}
-EXPORT_SYMBOL_GPL(sata_scr_write);
-
-/**
- * sata_scr_write_flush - write SCR register of the specified port and flush
- * @link: ATA link to write SCR for
- * @reg: SCR to write
- * @val: value to write
- *
- * This function is identical to sata_scr_write() except that this
- * function performs flush after writing to the register.
- *
- * LOCKING:
- * None if @link is ap->link. Kernel thread context otherwise.
- *
- * RETURNS:
- * 0 on success, negative errno on failure.
- */
-int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
-{
- if (ata_is_host_link(link)) {
- int rc;
-
- if (sata_scr_valid(link)) {
- rc = link->ap->ops->scr_write(link, reg, val);
- if (rc == 0)
- rc = link->ap->ops->scr_read(link, reg, &val);
- return rc;
- }
- return -EOPNOTSUPP;
- }
-
- return sata_pmp_scr_write(link, reg, val);
-}
-EXPORT_SYMBOL_GPL(sata_scr_write_flush);
-
/**
* ata_phys_link_online - test whether the given link is online
* @link: ATA link to test
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
index 04f1ecaf414c..1ef4c19864ac 100644
--- a/drivers/ata/libata-sata.c
+++ b/drivers/ata/libata-sata.c
@@ -12,6 +12,115 @@
#include "libata.h"
+/**
+ * sata_scr_valid - test whether SCRs are accessible
+ * @link: ATA link to test SCR accessibility for
+ *
+ * Test whether SCRs are accessible for @link.
+ *
+ * LOCKING:
+ * None.
+ *
+ * RETURNS:
+ * 1 if SCRs are accessible, 0 otherwise.
+ */
+int sata_scr_valid(struct ata_link *link)
+{
+ struct ata_port *ap = link->ap;
+
+ return (ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read;
+}
+EXPORT_SYMBOL_GPL(sata_scr_valid);
+
+/**
+ * sata_scr_read - read SCR register of the specified port
+ * @link: ATA link to read SCR for
+ * @reg: SCR to read
+ * @val: Place to store read value
+ *
+ * Read SCR register @reg of @link into *@val. This function is
+ * guaranteed to succeed if @link is ap->link, the cable type of
+ * the port is SATA and the port implements ->scr_read.
+ *
+ * LOCKING:
+ * None if @link is ap->link. Kernel thread context otherwise.
+ *
+ * RETURNS:
+ * 0 on success, negative errno on failure.
+ */
+int sata_scr_read(struct ata_link *link, int reg, u32 *val)
+{
+ if (ata_is_host_link(link)) {
+ if (sata_scr_valid(link))
+ return link->ap->ops->scr_read(link, reg, val);
+ return -EOPNOTSUPP;
+ }
+
+ return sata_pmp_scr_read(link, reg, val);
+}
+EXPORT_SYMBOL_GPL(sata_scr_read);
+
+/**
+ * sata_scr_write - write SCR register of the specified port
+ * @link: ATA link to write SCR for
+ * @reg: SCR to write
+ * @val: value to write
+ *
+ * Write @val to SCR register @reg of @link. This function is
+ * guaranteed to succeed if @link is ap->link, the cable type of
+ * the port is SATA and the port implements ->scr_read.
+ *
+ * LOCKING:
+ * None if @link is ap->link. Kernel thread context otherwise.
+ *
+ * RETURNS:
+ * 0 on success, negative errno on failure.
+ */
+int sata_scr_write(struct ata_link *link, int reg, u32 val)
+{
+ if (ata_is_host_link(link)) {
+ if (sata_scr_valid(link))
+ return link->ap->ops->scr_write(link, reg, val);
+ return -EOPNOTSUPP;
+ }
+
+ return sata_pmp_scr_write(link, reg, val);
+}
+EXPORT_SYMBOL_GPL(sata_scr_write);
+
+/**
+ * sata_scr_write_flush - write SCR register of the specified port and flush
+ * @link: ATA link to write SCR for
+ * @reg: SCR to write
+ * @val: value to write
+ *
+ * This function is identical to sata_scr_write() except that this
+ * function performs flush after writing to the register.
+ *
+ * LOCKING:
+ * None if @link is ap->link. Kernel thread context otherwise.
+ *
+ * RETURNS:
+ * 0 on success, negative errno on failure.
+ */
+int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
+{
+ if (ata_is_host_link(link)) {
+ int rc;
+
+ if (sata_scr_valid(link)) {
+ rc = link->ap->ops->scr_write(link, reg, val);
+ if (rc == 0)
+ rc = link->ap->ops->scr_read(link, reg, &val);
+ return rc;
+ }
+ return -EOPNOTSUPP;
+ }
+
+ return sata_pmp_scr_write(link, reg, val);
+}
+EXPORT_SYMBOL_GPL(sata_scr_write_flush);
+
/**
* ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
* @tf: Taskfile to convert
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 5d76eab000e9..372070a9d92e 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1127,10 +1127,6 @@ extern void ata_sas_tport_delete(struct ata_port *ap);
extern void ata_sas_port_stop(struct ata_port *ap);
extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap);
-extern int sata_scr_valid(struct ata_link *link);
-extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
-extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
-extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
extern bool ata_link_online(struct ata_link *link);
extern bool ata_link_offline(struct ata_link *link);
#ifdef CONFIG_PM
@@ -1195,6 +1191,26 @@ extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *
/*
* SATA specific code - drivers/ata/libata-sata.c
*/
+#ifdef CONFIG_SATA_HOST
+extern int sata_scr_valid(struct ata_link *link);
+extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
+extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
+extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
+#else
+static inline int sata_scr_valid(struct ata_link *link) { return 0; }
+static inline int sata_scr_read(struct ata_link *link, int reg, u32 *val)
+{
+ return -EOPNOTSUPP;
+}
+static inline int sata_scr_write(struct ata_link *link, int reg, u32 val)
+{
+ return -EOPNOTSUPP;
+}
+static inline int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
+{
+ return -EOPNOTSUPP;
+}
+#endif
extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
bool spm_wakeup);
extern int ata_slave_link_init(struct ata_port *ap);
--
2.24.1
* fix the overly long line in ata_timing_quantize()
* use standard kernel CodingStyle in ata_timing_merge()
* do not use assignment in if condition in ata_timing_compute()
* fix non-standard comment style in ata_timing_compute()
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 42 +++++++++++++++++++++++++--------------
1 file changed, 27 insertions(+), 15 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 2ec1a49388ee..acdcedcb3d10 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3251,7 +3251,8 @@ static const struct ata_timing ata_timing[] = {
#define ENOUGH(v, unit) (((v)-1)/(unit)+1)
#define EZ(v, unit) ((v)?ENOUGH(((v) * 1000), unit):0)
-static void ata_timing_quantize(const struct ata_timing *t, struct ata_timing *q, int T, int UT)
+static void ata_timing_quantize(const struct ata_timing *t,
+ struct ata_timing *q, int T, int UT)
{
q->setup = EZ(t->setup, T);
q->act8b = EZ(t->act8b, T);
@@ -3267,15 +3268,24 @@ static void ata_timing_quantize(const struct ata_timing *t, struct ata_timing *q
void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
struct ata_timing *m, unsigned int what)
{
- if (what & ATA_TIMING_SETUP ) m->setup = max(a->setup, b->setup);
- if (what & ATA_TIMING_ACT8B ) m->act8b = max(a->act8b, b->act8b);
- if (what & ATA_TIMING_REC8B ) m->rec8b = max(a->rec8b, b->rec8b);
- if (what & ATA_TIMING_CYC8B ) m->cyc8b = max(a->cyc8b, b->cyc8b);
- if (what & ATA_TIMING_ACTIVE ) m->active = max(a->active, b->active);
- if (what & ATA_TIMING_RECOVER) m->recover = max(a->recover, b->recover);
- if (what & ATA_TIMING_DMACK_HOLD) m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
- if (what & ATA_TIMING_CYCLE ) m->cycle = max(a->cycle, b->cycle);
- if (what & ATA_TIMING_UDMA ) m->udma = max(a->udma, b->udma);
+ if (what & ATA_TIMING_SETUP)
+ m->setup = max(a->setup, b->setup);
+ if (what & ATA_TIMING_ACT8B)
+ m->act8b = max(a->act8b, b->act8b);
+ if (what & ATA_TIMING_REC8B)
+ m->rec8b = max(a->rec8b, b->rec8b);
+ if (what & ATA_TIMING_CYC8B)
+ m->cyc8b = max(a->cyc8b, b->cyc8b);
+ if (what & ATA_TIMING_ACTIVE)
+ m->active = max(a->active, b->active);
+ if (what & ATA_TIMING_RECOVER)
+ m->recover = max(a->recover, b->recover);
+ if (what & ATA_TIMING_DMACK_HOLD)
+ m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
+ if (what & ATA_TIMING_CYCLE)
+ m->cycle = max(a->cycle, b->cycle);
+ if (what & ATA_TIMING_UDMA)
+ m->udma = max(a->udma, b->udma);
}
EXPORT_SYMBOL_GPL(ata_timing_merge);
@@ -3306,8 +3316,8 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
/*
* Find the mode.
*/
-
- if (!(s = ata_timing_find_mode(speed)))
+ s = ata_timing_find_mode(speed);
+ if (!s)
return -EINVAL;
memcpy(t, s, sizeof(*s));
@@ -3363,9 +3373,11 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
t->recover = t->cycle - t->active;
}
- /* In a few cases quantisation may produce enough errors to
- leave t->cycle too low for the sum of active and recovery
- if so we must correct this */
+ /*
+ * In a few cases quantisation may produce enough errors to
+ * leave t->cycle too low for the sum of active and recovery
+ * if so we must correct this.
+ */
if (t->active + t->recover > t->cycle)
t->cycle = t->active + t->recover;
--
2.24.1
Currently the maximum required size of the ata_scsi_rbuf[] is
576 bytes in ata_scsiop_inq_89() so modify ATA_SCSI_RBUF_SIZE
define accordingly.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
20782 105 4096 24983 6197 drivers/ata/libata-scsi.o
after:
20782 105 576 21463 53d7 drivers/ata/libata-scsi.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-scsi.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index cc8ba49275e7..b64b0b0dfb21 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -36,7 +36,7 @@
#include "libata.h"
#include "libata-transport.h"
-#define ATA_SCSI_RBUF_SIZE 4096
+#define ATA_SCSI_RBUF_SIZE 576
static DEFINE_SPINLOCK(ata_scsi_rbuf_lock);
static u8 ata_scsi_rbuf[ATA_SCSI_RBUF_SIZE];
--
2.24.1
Optimize struct ata_force_param size by:
- using u8 for cbl and spd_limit fields
- using u16 for lflags field
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
after:
40654 573 40 41267 a133 drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 6 +++---
include/linux/libata.h | 1 +
2 files changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index a9a8762448aa..a835d2bf243e 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -90,12 +90,12 @@ atomic_t ata_print_id = ATOMIC_INIT(0);
struct ata_force_param {
const char *name;
- unsigned int cbl;
- int spd_limit;
+ u8 cbl;
+ u8 spd_limit;
unsigned long xfer_mask;
unsigned int horkage_on;
unsigned int horkage_off;
- unsigned int lflags;
+ u16 lflags;
};
struct ata_force_ent {
diff --git a/include/linux/libata.h b/include/linux/libata.h
index df8f20a2a305..df7c1b538bb1 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -176,6 +176,7 @@ enum {
ATA_DEV_NONE = 11, /* no device */
/* struct ata_link flags */
+ /* NOTE: struct ata_force_param currently stores lflags in u16 */
ATA_LFLAG_NO_HRST = (1 << 1), /* avoid hardreset */
ATA_LFLAG_NO_SRST = (1 << 2), /* avoid softreset */
ATA_LFLAG_ASSUME_ATA = (1 << 3), /* assume ATA class */
--
2.24.1
Remove EXPORT_SYMBOL_GPL()s for functions used only by
the core libata code.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
39838 573 40 40451 9e03 drivers/ata/libata-core.o
21071 105 576 21752 54f8 drivers/ata/libata-scsi.o
17519 18 0 17537 4481 drivers/ata/libata-eh.o
after:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
21040 105 576 21721 54d9 drivers/ata/libata-scsi.o
17405 18 0 17423 440f drivers/ata/libata-eh.o
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 5 -----
drivers/ata/libata-eh.c | 4 ----
drivers/ata/libata-scsi.c | 1 -
3 files changed, 10 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index dc48e983ccdb..2ec1a49388ee 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -80,7 +80,6 @@ const struct ata_port_operations ata_base_port_ops = {
.sched_eh = ata_std_sched_eh,
.end_eh = ata_std_end_eh,
};
-EXPORT_SYMBOL_GPL(ata_base_port_ops);
const struct ata_port_operations sata_port_ops = {
.inherits = &ata_base_port_ops,
@@ -902,7 +901,6 @@ void ata_unpack_xfermask(unsigned long xfer_mask, unsigned long *pio_mask,
if (udma_mask)
*udma_mask = (xfer_mask & ATA_MASK_UDMA) >> ATA_SHIFT_UDMA;
}
-EXPORT_SYMBOL_GPL(ata_unpack_xfermask);
static const struct ata_xfer_ent {
int shift, bits;
@@ -3425,7 +3423,6 @@ u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle)
return last_mode;
}
-EXPORT_SYMBOL_GPL(ata_timing_cycle2mode);
/**
* ata_down_xfermask_limit - adjust dev xfer masks downward
@@ -5051,7 +5048,6 @@ void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
qc->n_elem = n_elem;
qc->cursg = qc->sg;
}
-EXPORT_SYMBOL_GPL(ata_sg_init);
#ifdef CONFIG_HAS_DMA
@@ -6157,7 +6153,6 @@ void ata_host_get(struct ata_host *host)
{
kref_get(&host->kref);
}
-EXPORT_SYMBOL_GPL(ata_host_get);
void ata_host_put(struct ata_host *host)
{
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 1d231cfab26f..04275f4c8d36 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1215,7 +1215,6 @@ void ata_eh_thaw_port(struct ata_port *ap)
DPRINTK("ata%u port thawed\n", ap->print_id);
}
-EXPORT_SYMBOL_GPL(ata_eh_thaw_port);
static void ata_eh_scsidone(struct scsi_cmnd *scmd)
{
@@ -1250,7 +1249,6 @@ void ata_eh_qc_complete(struct ata_queued_cmd *qc)
scmd->retries = scmd->allowed;
__ata_eh_qc_complete(qc);
}
-EXPORT_SYMBOL_GPL(ata_eh_qc_complete);
/**
* ata_eh_qc_retry - Tell midlayer to retry an ATA command after EH
@@ -1270,7 +1268,6 @@ void ata_eh_qc_retry(struct ata_queued_cmd *qc)
scmd->allowed++;
__ata_eh_qc_complete(qc);
}
-EXPORT_SYMBOL_GPL(ata_eh_qc_retry);
/**
* ata_dev_disable - disable ATA device
@@ -4041,7 +4038,6 @@ void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_eh_finish(ap);
}
-EXPORT_SYMBOL_GPL(ata_do_eh);
/**
* ata_std_error_handler - standard error handler
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index a779ea57f3ad..b8e41c8e6395 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -4535,7 +4535,6 @@ void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd)
cmd->scsi_done(cmd);
}
-EXPORT_SYMBOL_GPL(ata_scsi_simulate);
int ata_scsi_add_hosts(struct ata_host *host, struct scsi_host_template *sht)
{
--
2.24.1
Initialize rbuf[] directly instead of using ata_tf_to_fis(). This
results in simpler and smaller code. It also allows separating
ata_tf_to_fis() into SATA specific libata part in the future.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
20824 105 4096 25025 61c1 drivers/ata/libata-scsi.o
after:
20782 105 4096 24983 6197 drivers/ata/libata-scsi.o
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-scsi.c | 18 +++++++-----------
1 file changed, 7 insertions(+), 11 deletions(-)
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 161e5d84bd82..cc8ba49275e7 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -2356,10 +2356,6 @@ static unsigned int ata_scsiop_inq_83(struct ata_scsi_args *args, u8 *rbuf)
*/
static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf)
{
- struct ata_taskfile tf;
-
- memset(&tf, 0, sizeof(tf));
-
rbuf[1] = 0x89; /* our page code */
rbuf[2] = (0x238 >> 8); /* page size fixed at 238h */
rbuf[3] = (0x238 & 0xff);
@@ -2368,14 +2364,14 @@ static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf)
memcpy(&rbuf[16], "libata ", 16);
memcpy(&rbuf[32], DRV_VERSION, 4);
- /* we don't store the ATA device signature, so we fake it */
-
- tf.command = ATA_DRDY; /* really, this is Status reg */
- tf.lbal = 0x1;
- tf.nsect = 0x1;
-
- ata_tf_to_fis(&tf, 0, 1, &rbuf[36]); /* TODO: PMP? */
rbuf[36] = 0x34; /* force D2H Reg FIS (34h) */
+ rbuf[37] = (1 << 7); /* bit 7 indicates Command FIS */
+ /* TODO: PMP? */
+
+ /* we don't store the ATA device signature, so we fake it */
+ rbuf[38] = ATA_DRDY; /* really, this is Status reg */
+ rbuf[40] = 0x1;
+ rbuf[48] = 0x1;
rbuf[56] = ATA_CMD_ID_ATA;
--
2.24.1
Start separating SATA specific code from libata-core.c:
* move following functions to libata-sata.c:
- ata_tf_to_fis()
- ata_tf_from_fis()
- sata_link_scr_lpm()
- ata_slave_link_init()
- sata_lpm_ignore_phy_events()
* group above functions together in <linux/libata.h>
* include libata-sata.c in the build when CONFIG_SATA_HOST=y
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36762 572 40 37374 91fe drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/Makefile | 1 +
drivers/ata/libata-core.c | 245 ------------------------------------
drivers/ata/libata-sata.c | 258 ++++++++++++++++++++++++++++++++++++++
include/linux/libata.h | 16 ++-
4 files changed, 269 insertions(+), 251 deletions(-)
create mode 100644 drivers/ata/libata-sata.c
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index cdaf965fed25..b8aebfb14e82 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -123,6 +123,7 @@ obj-$(CONFIG_PATA_LEGACY) += pata_legacy.o
libata-y := libata-core.o libata-scsi.o libata-eh.o \
libata-transport.o libata-trace.o
+libata-$(CONFIG_SATA_HOST) += libata-sata.o
libata-$(CONFIG_ATA_SFF) += libata-sff.o
libata-$(CONFIG_SATA_PMP) += libata-pmp.o
libata-$(CONFIG_ATA_ACPI) += libata-acpi.o
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index dcdb7fb46dbd..b4a952dce7ab 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -531,81 +531,6 @@ int atapi_cmd_type(u8 opcode)
}
EXPORT_SYMBOL_GPL(atapi_cmd_type);
-/**
- * ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
- * @tf: Taskfile to convert
- * @pmp: Port multiplier port
- * @is_cmd: This FIS is for command
- * @fis: Buffer into which data will output
- *
- * Converts a standard ATA taskfile to a Serial ATA
- * FIS structure (Register - Host to Device).
- *
- * LOCKING:
- * Inherited from caller.
- */
-void ata_tf_to_fis(const struct ata_taskfile *tf, u8 pmp, int is_cmd, u8 *fis)
-{
- fis[0] = 0x27; /* Register - Host to Device FIS */
- fis[1] = pmp & 0xf; /* Port multiplier number*/
- if (is_cmd)
- fis[1] |= (1 << 7); /* bit 7 indicates Command FIS */
-
- fis[2] = tf->command;
- fis[3] = tf->feature;
-
- fis[4] = tf->lbal;
- fis[5] = tf->lbam;
- fis[6] = tf->lbah;
- fis[7] = tf->device;
-
- fis[8] = tf->hob_lbal;
- fis[9] = tf->hob_lbam;
- fis[10] = tf->hob_lbah;
- fis[11] = tf->hob_feature;
-
- fis[12] = tf->nsect;
- fis[13] = tf->hob_nsect;
- fis[14] = 0;
- fis[15] = tf->ctl;
-
- fis[16] = tf->auxiliary & 0xff;
- fis[17] = (tf->auxiliary >> 8) & 0xff;
- fis[18] = (tf->auxiliary >> 16) & 0xff;
- fis[19] = (tf->auxiliary >> 24) & 0xff;
-}
-EXPORT_SYMBOL_GPL(ata_tf_to_fis);
-
-/**
- * ata_tf_from_fis - Convert SATA FIS to ATA taskfile
- * @fis: Buffer from which data will be input
- * @tf: Taskfile to output
- *
- * Converts a serial ATA FIS structure to a standard ATA taskfile.
- *
- * LOCKING:
- * Inherited from caller.
- */
-
-void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf)
-{
- tf->command = fis[2]; /* status */
- tf->feature = fis[3]; /* error */
-
- tf->lbal = fis[4];
- tf->lbam = fis[5];
- tf->lbah = fis[6];
- tf->device = fis[7];
-
- tf->hob_lbal = fis[8];
- tf->hob_lbam = fis[9];
- tf->hob_lbah = fis[10];
-
- tf->nsect = fis[12];
- tf->hob_nsect = fis[13];
-}
-EXPORT_SYMBOL_GPL(ata_tf_from_fis);
-
static const u8 ata_rw_cmds[] = {
/* pio multi */
ATA_CMD_READ_MULTI,
@@ -3779,81 +3704,6 @@ int sata_link_resume(struct ata_link *link, const unsigned long *params,
}
EXPORT_SYMBOL_GPL(sata_link_resume);
-/**
- * sata_link_scr_lpm - manipulate SControl IPM and SPM fields
- * @link: ATA link to manipulate SControl for
- * @policy: LPM policy to configure
- * @spm_wakeup: initiate LPM transition to active state
- *
- * Manipulate the IPM field of the SControl register of @link
- * according to @policy. If @policy is ATA_LPM_MAX_POWER and
- * @spm_wakeup is %true, the SPM field is manipulated to wake up
- * the link. This function also clears PHYRDY_CHG before
- * returning.
- *
- * LOCKING:
- * EH context.
- *
- * RETURNS:
- * 0 on success, -errno otherwise.
- */
-int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
- bool spm_wakeup)
-{
- struct ata_eh_context *ehc = &link->eh_context;
- bool woken_up = false;
- u32 scontrol;
- int rc;
-
- rc = sata_scr_read(link, SCR_CONTROL, &scontrol);
- if (rc)
- return rc;
-
- switch (policy) {
- case ATA_LPM_MAX_POWER:
- /* disable all LPM transitions */
- scontrol |= (0x7 << 8);
- /* initiate transition to active state */
- if (spm_wakeup) {
- scontrol |= (0x4 << 12);
- woken_up = true;
- }
- break;
- case ATA_LPM_MED_POWER:
- /* allow LPM to PARTIAL */
- scontrol &= ~(0x1 << 8);
- scontrol |= (0x6 << 8);
- break;
- case ATA_LPM_MED_POWER_WITH_DIPM:
- case ATA_LPM_MIN_POWER_WITH_PARTIAL:
- case ATA_LPM_MIN_POWER:
- if (ata_link_nr_enabled(link) > 0)
- /* no restrictions on LPM transitions */
- scontrol &= ~(0x7 << 8);
- else {
- /* empty port, power off */
- scontrol &= ~0xf;
- scontrol |= (0x1 << 2);
- }
- break;
- default:
- WARN_ON(1);
- }
-
- rc = sata_scr_write(link, SCR_CONTROL, scontrol);
- if (rc)
- return rc;
-
- /* give the link time to transit out of LPM state */
- if (woken_up)
- msleep(10);
-
- /* clear PHYRDY_CHG from SError */
- ehc->i.serror &= ~SERR_PHYRDY_CHG;
- return sata_scr_write(link, SCR_ERROR, SERR_PHYRDY_CHG);
-}
-EXPORT_SYMBOL_GPL(sata_link_scr_lpm);
-
/**
* ata_std_prereset - prepare for reset
* @link: ATA link to be reset
@@ -6118,69 +5968,6 @@ struct ata_host *ata_host_alloc_pinfo(struct device *dev,
}
EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);
-/**
- * ata_slave_link_init - initialize slave link
- * @ap: port to initialize slave link for
- *
- * Create and initialize slave link for @ap. This enables slave
- * link handling on the port.
- *
- * In libata, a port contains links and a link contains devices.
- * There is single host link but if a PMP is attached to it,
- * there can be multiple fan-out links. On SATA, there's usually
- * a single device connected to a link but PATA and SATA
- * controllers emulating TF based interface can have two - master
- * and slave.
- *
- * However, there are a few controllers which don't fit into this
- * abstraction too well - SATA controllers which emulate TF
- * interface with both master and slave devices but also have
- * separate SCR register sets for each device. These controllers
- * need separate links for physical link handling
- * (e.g. onlineness, link speed) but should be treated like a
- * traditional M/S controller for everything else (e.g. command
- * issue, softreset).
- *
- * slave_link is libata's way of handling this class of
- * controllers without impacting core layer too much. For
- * anything other than physical link handling, the default host
- * link is used for both master and slave. For physical link
- * handling, separate @ap->slave_link is used. All dirty details
- * are implemented inside libata core layer. From LLD's POV, the
- * only difference is that prereset, hardreset and postreset are
- * called once more for the slave link, so the reset sequence
- * looks like the following.
- *
- * prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
- * softreset(M) -> postreset(M) -> postreset(S)
- *
- * Note that softreset is called only for the master. Softreset
- * resets both M/S by definition, so SRST on master should handle
- * both (the standard method will work just fine).
- *
- * LOCKING:
- * Should be called before host is registered.
- *
- * RETURNS:
- * 0 on success, -errno on failure.
- */
-int ata_slave_link_init(struct ata_port *ap)
-{
- struct ata_link *link;
-
- WARN_ON(ap->slave_link);
- WARN_ON(ap->flags & ATA_FLAG_PMP);
-
- link = kzalloc(sizeof(*link), GFP_KERNEL);
- if (!link)
- return -ENOMEM;
-
- ata_link_init(ap, link, 1);
- ap->slave_link = link;
- return 0;
-}
-EXPORT_SYMBOL_GPL(ata_slave_link_init);
-
static void ata_host_stop(struct device *gendev, void *res)
{
struct ata_host *host = dev_get_drvdata(gendev);
@@ -7106,38 +6893,6 @@ u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val,
}
EXPORT_SYMBOL_GPL(ata_wait_register);
-/**
- * sata_lpm_ignore_phy_events - test if PHY event should be ignored
- * @link: Link receiving the event
- *
- * Test whether the received PHY event has to be ignored or not.
- *
- * LOCKING:
- * None:
- *
- * RETURNS:
- * True if the event has to be ignored.
- */
-bool sata_lpm_ignore_phy_events(struct ata_link *link)
-{
- unsigned long lpm_timeout = link->last_lpm_change +
- msecs_to_jiffies(ATA_TMOUT_SPURIOUS_PHY);
-
- /* if LPM is enabled, PHYRDY doesn't mean anything */
- if (link->lpm_policy > ATA_LPM_MAX_POWER)
- return true;
-
- /* ignore the first PHY event after the LPM policy changed
- * as it is might be spurious
- */
- if ((link->flags & ATA_LFLAG_CHANGED) &&
- time_before(jiffies, lpm_timeout))
- return true;
-
- return false;
-}
-EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
-
/*
* Dummy port_ops
*/
diff --git a/drivers/ata/libata-sata.c b/drivers/ata/libata-sata.c
new file mode 100644
index 000000000000..04f1ecaf414c
--- /dev/null
+++ b/drivers/ata/libata-sata.c
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * SATA specific part of ATA helper library
+ *
+ * Copyright 2003-2004 Red Hat, Inc. All rights reserved.
+ * Copyright 2003-2004 Jeff Garzik
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/libata.h>
+
+#include "libata.h"
+
+/**
+ * ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
+ * @tf: Taskfile to convert
+ * @pmp: Port multiplier port
+ * @is_cmd: This FIS is for command
+ * @fis: Buffer into which data will output
+ *
+ * Converts a standard ATA taskfile to a Serial ATA
+ * FIS structure (Register - Host to Device).
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+void ata_tf_to_fis(const struct ata_taskfile *tf, u8 pmp, int is_cmd, u8 *fis)
+{
+ fis[0] = 0x27; /* Register - Host to Device FIS */
+ fis[1] = pmp & 0xf; /* Port multiplier number*/
+ if (is_cmd)
+ fis[1] |= (1 << 7); /* bit 7 indicates Command FIS */
+
+ fis[2] = tf->command;
+ fis[3] = tf->feature;
+
+ fis[4] = tf->lbal;
+ fis[5] = tf->lbam;
+ fis[6] = tf->lbah;
+ fis[7] = tf->device;
+
+ fis[8] = tf->hob_lbal;
+ fis[9] = tf->hob_lbam;
+ fis[10] = tf->hob_lbah;
+ fis[11] = tf->hob_feature;
+
+ fis[12] = tf->nsect;
+ fis[13] = tf->hob_nsect;
+ fis[14] = 0;
+ fis[15] = tf->ctl;
+
+ fis[16] = tf->auxiliary & 0xff;
+ fis[17] = (tf->auxiliary >> 8) & 0xff;
+ fis[18] = (tf->auxiliary >> 16) & 0xff;
+ fis[19] = (tf->auxiliary >> 24) & 0xff;
+}
+EXPORT_SYMBOL_GPL(ata_tf_to_fis);
+
+/**
+ * ata_tf_from_fis - Convert SATA FIS to ATA taskfile
+ * @fis: Buffer from which data will be input
+ * @tf: Taskfile to output
+ *
+ * Converts a serial ATA FIS structure to a standard ATA taskfile.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
+void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf)
+{
+ tf->command = fis[2]; /* status */
+ tf->feature = fis[3]; /* error */
+
+ tf->lbal = fis[4];
+ tf->lbam = fis[5];
+ tf->lbah = fis[6];
+ tf->device = fis[7];
+
+ tf->hob_lbal = fis[8];
+ tf->hob_lbam = fis[9];
+ tf->hob_lbah = fis[10];
+
+ tf->nsect = fis[12];
+ tf->hob_nsect = fis[13];
+}
+EXPORT_SYMBOL_GPL(ata_tf_from_fis);
+
+/**
+ * sata_link_scr_lpm - manipulate SControl IPM and SPM fields
+ * @link: ATA link to manipulate SControl for
+ * @policy: LPM policy to configure
+ * @spm_wakeup: initiate LPM transition to active state
+ *
+ * Manipulate the IPM field of the SControl register of @link
+ * according to @policy. If @policy is ATA_LPM_MAX_POWER and
+ * @spm_wakeup is %true, the SPM field is manipulated to wake up
+ * the link. This function also clears PHYRDY_CHG before
+ * returning.
+ *
+ * LOCKING:
+ * EH context.
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
+ bool spm_wakeup)
+{
+ struct ata_eh_context *ehc = &link->eh_context;
+ bool woken_up = false;
+ u32 scontrol;
+ int rc;
+
+ rc = sata_scr_read(link, SCR_CONTROL, &scontrol);
+ if (rc)
+ return rc;
+
+ switch (policy) {
+ case ATA_LPM_MAX_POWER:
+ /* disable all LPM transitions */
+ scontrol |= (0x7 << 8);
+ /* initiate transition to active state */
+ if (spm_wakeup) {
+ scontrol |= (0x4 << 12);
+ woken_up = true;
+ }
+ break;
+ case ATA_LPM_MED_POWER:
+ /* allow LPM to PARTIAL */
+ scontrol &= ~(0x1 << 8);
+ scontrol |= (0x6 << 8);
+ break;
+ case ATA_LPM_MED_POWER_WITH_DIPM:
+ case ATA_LPM_MIN_POWER_WITH_PARTIAL:
+ case ATA_LPM_MIN_POWER:
+ if (ata_link_nr_enabled(link) > 0)
+ /* no restrictions on LPM transitions */
+ scontrol &= ~(0x7 << 8);
+ else {
+ /* empty port, power off */
+ scontrol &= ~0xf;
+ scontrol |= (0x1 << 2);
+ }
+ break;
+ default:
+ WARN_ON(1);
+ }
+
+ rc = sata_scr_write(link, SCR_CONTROL, scontrol);
+ if (rc)
+ return rc;
+
+ /* give the link time to transit out of LPM state */
+ if (woken_up)
+ msleep(10);
+
+ /* clear PHYRDY_CHG from SError */
+ ehc->i.serror &= ~SERR_PHYRDY_CHG;
+ return sata_scr_write(link, SCR_ERROR, SERR_PHYRDY_CHG);
+}
+EXPORT_SYMBOL_GPL(sata_link_scr_lpm);
+
+/**
+ * ata_slave_link_init - initialize slave link
+ * @ap: port to initialize slave link for
+ *
+ * Create and initialize slave link for @ap. This enables slave
+ * link handling on the port.
+ *
+ * In libata, a port contains links and a link contains devices.
+ * There is single host link but if a PMP is attached to it,
+ * there can be multiple fan-out links. On SATA, there's usually
+ * a single device connected to a link but PATA and SATA
+ * controllers emulating TF based interface can have two - master
+ * and slave.
+ *
+ * However, there are a few controllers which don't fit into this
+ * abstraction too well - SATA controllers which emulate TF
+ * interface with both master and slave devices but also have
+ * separate SCR register sets for each device. These controllers
+ * need separate links for physical link handling
+ * (e.g. onlineness, link speed) but should be treated like a
+ * traditional M/S controller for everything else (e.g. command
+ * issue, softreset).
+ *
+ * slave_link is libata's way of handling this class of
+ * controllers without impacting core layer too much. For
+ * anything other than physical link handling, the default host
+ * link is used for both master and slave. For physical link
+ * handling, separate @ap->slave_link is used. All dirty details
+ * are implemented inside libata core layer. From LLD's POV, the
+ * only difference is that prereset, hardreset and postreset are
+ * called once more for the slave link, so the reset sequence
+ * looks like the following.
+ *
+ * prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
+ * softreset(M) -> postreset(M) -> postreset(S)
+ *
+ * Note that softreset is called only for the master. Softreset
+ * resets both M/S by definition, so SRST on master should handle
+ * both (the standard method will work just fine).
+ *
+ * LOCKING:
+ * Should be called before host is registered.
+ *
+ * RETURNS:
+ * 0 on success, -errno on failure.
+ */
+int ata_slave_link_init(struct ata_port *ap)
+{
+ struct ata_link *link;
+
+ WARN_ON(ap->slave_link);
+ WARN_ON(ap->flags & ATA_FLAG_PMP);
+
+ link = kzalloc(sizeof(*link), GFP_KERNEL);
+ if (!link)
+ return -ENOMEM;
+
+ ata_link_init(ap, link, 1);
+ ap->slave_link = link;
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_slave_link_init);
+
+/**
+ * sata_lpm_ignore_phy_events - test if PHY event should be ignored
+ * @link: Link receiving the event
+ *
+ * Test whether the received PHY event has to be ignored or not.
+ *
+ * LOCKING:
+ * None:
+ *
+ * RETURNS:
+ * True if the event has to be ignored.
+ */
+bool sata_lpm_ignore_phy_events(struct ata_link *link)
+{
+ unsigned long lpm_timeout = link->last_lpm_change +
+ msecs_to_jiffies(ATA_TMOUT_SPURIOUS_PHY);
+
+ /* if LPM is enabled, PHYRDY doesn't mean anything */
+ if (link->lpm_policy > ATA_LPM_MAX_POWER)
+ return true;
+
+ /* ignore the first PHY event after the LPM policy changed
+ * as it is might be spurious
+ */
+ if ((link->flags & ATA_LFLAG_CHANGED) &&
+ time_before(jiffies, lpm_timeout))
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index ce361b15559b..5d76eab000e9 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1084,8 +1084,6 @@ extern int sata_link_debounce(struct ata_link *link,
const unsigned long *params, unsigned long deadline);
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
-extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
- bool spm_wakeup);
extern int sata_link_hardreset(struct ata_link *link,
const unsigned long *timing, unsigned long deadline,
bool *online, int (*check_ready)(struct ata_link *));
@@ -1096,7 +1094,6 @@ extern void ata_std_postreset(struct ata_link *link, unsigned int *classes);
extern struct ata_host *ata_host_alloc(struct device *dev, int max_ports);
extern struct ata_host *ata_host_alloc_pinfo(struct device *dev,
const struct ata_port_info * const * ppi, int n_ports);
-extern int ata_slave_link_init(struct ata_port *ap);
extern void ata_host_get(struct ata_host *host);
extern void ata_host_put(struct ata_host *host);
extern int ata_host_start(struct ata_host *host);
@@ -1154,9 +1151,6 @@ extern void ata_msleep(struct ata_port *ap, unsigned int msecs);
extern u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask,
u32 val, unsigned long interval, unsigned long timeout);
extern int atapi_cmd_type(u8 opcode);
-extern void ata_tf_to_fis(const struct ata_taskfile *tf,
- u8 pmp, int is_cmd, u8 *fis);
-extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
extern unsigned long ata_pack_xfermask(unsigned long pio_mask,
unsigned long mwdma_mask, unsigned long udma_mask);
extern void ata_unpack_xfermask(unsigned long xfer_mask,
@@ -1197,6 +1191,16 @@ extern struct ata_device *ata_dev_pair(struct ata_device *adev);
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap);
extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *ap, struct list_head *eh_q);
+
+/*
+ * SATA specific code - drivers/ata/libata-sata.c
+ */
+extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
+ bool spm_wakeup);
+extern int ata_slave_link_init(struct ata_port *ap);
+extern void ata_tf_to_fis(const struct ata_taskfile *tf,
+ u8 pmp, int is_cmd, u8 *fis);
+extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
extern int ata_cable_40wire(struct ata_port *ap);
--
2.24.1
Add !IS_ENABLED(CONFIG_SATA_HOST) to ata_eh_set_lpm() to allow
compiler to optimize out the function for non-SATA configs (for
PATA hosts "ap && !ap->ops->set_lpm" condition is always true so
it's sufficient for the function to return zero).
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
17353 18 0 17371 43db drivers/ata/libata-eh.o
after:
16607 18 0 16625 40f1 drivers/ata/libata-eh.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-eh.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 04275f4c8d36..8dc33b6832f0 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -3443,7 +3443,8 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
int rc;
/* if the link or host doesn't do LPM, noop */
- if ((link->flags & ATA_LFLAG_NO_LPM) || (ap && !ap->ops->set_lpm))
+ if (!IS_ENABLED(CONFIG_SATA_HOST) ||
+ (link->flags & ATA_LFLAG_NO_LPM) || (ap && !ap->ops->set_lpm))
return 0;
/*
--
2.24.1
There is no point in exposing ncq_enable_prio sysfs attribute for
devices on PATA and non-NCQ capable SATA hosts so:
* remove dev_attr_ncq_prio_enable from ata_common_sdev_attrs[]
* add ata_ncq_sdev_attrs[]
* update ATA_NCQ_SHT() macro to use ata_ncq_sdev_attrs[]
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-scsi.c | 8 +++++++-
include/linux/libata.h | 2 ++
2 files changed, 9 insertions(+), 1 deletion(-)
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index 11eb25b6e2cd..161e5d84bd82 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -462,11 +462,17 @@ EXPORT_SYMBOL_GPL(dev_attr_sw_activity);
struct device_attribute *ata_common_sdev_attrs[] = {
&dev_attr_unload_heads,
- &dev_attr_ncq_prio_enable,
NULL
};
EXPORT_SYMBOL_GPL(ata_common_sdev_attrs);
+struct device_attribute *ata_ncq_sdev_attrs[] = {
+ &dev_attr_unload_heads,
+ &dev_attr_ncq_prio_enable,
+ NULL
+};
+EXPORT_SYMBOL_GPL(ata_ncq_sdev_attrs);
+
/**
* ata_std_bios_param - generic bios head/sector/cylinder calculator used by sd.
* @sdev: SCSI device for which BIOS geometry is to be determined
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 2ca9b7056a82..df8f20a2a305 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -1336,6 +1336,7 @@ extern int ata_link_nr_enabled(struct ata_link *link);
extern const struct ata_port_operations ata_base_port_ops;
extern const struct ata_port_operations sata_port_ops;
extern struct device_attribute *ata_common_sdev_attrs[];
+extern struct device_attribute *ata_ncq_sdev_attrs[];
/*
* All sht initializers (BASE, PIO, BMDMA, NCQ) must be instantiated
@@ -1362,6 +1363,7 @@ extern struct device_attribute *ata_common_sdev_attrs[];
#define ATA_NCQ_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
+ .sdev_attrs = ata_ncq_sdev_attrs, \
.change_queue_depth = ata_scsi_change_queue_depth
/*
--
2.24.1
Add !IS_ENABLED(CONFIG_SATA_HOST) to ata_dev_config_ncq() to allow
compiler to optimize out the function for non-SATA configs.
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36462 572 40 37074 90d2 drivers/ata/libata-core.o
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 0a56968e2e98..dcdb7fb46dbd 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2287,6 +2287,8 @@ static int ata_dev_config_ncq(struct ata_device *dev,
desc[0] = '\0';
return 0;
}
+ if (!IS_ENABLED(CONFIG_SATA_HOST))
+ return 0;
if (dev->horkage & ATA_HORKAGE_NONCQ) {
snprintf(desc, desc_sz, "NCQ (not used)");
return 0;
--
2.24.1
Move EXPORT_SYMBOL_GPL()s close to exported code like it is
done in other kernel subsystems. As a nice side effect this
results in the removal of few ifdefs.
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 208 +++++++++++++++-----------------------
drivers/ata/libata-eh.c | 20 +++-
drivers/ata/libata-scsi.c | 8 ++
3 files changed, 109 insertions(+), 127 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index a835d2bf243e..dc48e983ccdb 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -18,6 +18,11 @@
* http://www.compactflash.org (CF)
* http://www.qic.org (QIC157 - Tape and DSC)
* http://www.ce-ata.org (CE-ATA: not supported)
+ *
+ * libata is essentially a library of internal helper functions for
+ * low-level ATA host controller drivers. As such, the API/ABI is
+ * likely to change as new drivers are added and updated.
+ * Do not depend on ABI/API stability.
*/
#include <linux/kernel.h>
@@ -62,8 +67,11 @@
/* debounce timing parameters in msecs { interval, duration, timeout } */
const unsigned long sata_deb_timing_normal[] = { 5, 100, 2000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
const unsigned long sata_deb_timing_hotplug[] = { 25, 500, 2000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
const unsigned long sata_deb_timing_long[] = { 100, 2000, 5000 };
+EXPORT_SYMBOL_GPL(sata_deb_timing_long);
const struct ata_port_operations ata_base_port_ops = {
.prereset = ata_std_prereset,
@@ -72,6 +80,7 @@ const struct ata_port_operations ata_base_port_ops = {
.sched_eh = ata_std_sched_eh,
.end_eh = ata_std_end_eh,
};
+EXPORT_SYMBOL_GPL(ata_base_port_ops);
const struct ata_port_operations sata_port_ops = {
.inherits = &ata_base_port_ops,
@@ -79,6 +88,7 @@ const struct ata_port_operations sata_port_ops = {
.qc_defer = ata_std_qc_defer,
.hardreset = sata_std_hardreset,
};
+EXPORT_SYMBOL_GPL(sata_port_ops);
static unsigned int ata_dev_init_params(struct ata_device *dev,
u16 heads, u16 sectors);
@@ -221,6 +231,7 @@ struct ata_link *ata_link_next(struct ata_link *link, struct ata_port *ap,
return NULL;
}
+EXPORT_SYMBOL_GPL(ata_link_next);
/**
* ata_dev_next - device iteration helper
@@ -274,6 +285,7 @@ struct ata_device *ata_dev_next(struct ata_device *dev, struct ata_link *link,
goto next;
return dev;
}
+EXPORT_SYMBOL_GPL(ata_dev_next);
/**
* ata_dev_phys_link - find physical link for a device
@@ -518,6 +530,7 @@ int atapi_cmd_type(u8 opcode)
return ATAPI_MISC;
}
}
+EXPORT_SYMBOL_GPL(atapi_cmd_type);
/**
* ata_tf_to_fis - Convert ATA taskfile to SATA FIS structure
@@ -562,6 +575,7 @@ void ata_tf_to_fis(const struct ata_taskfile *tf, u8 pmp, int is_cmd, u8 *fis)
fis[18] = (tf->auxiliary >> 16) & 0xff;
fis[19] = (tf->auxiliary >> 24) & 0xff;
}
+EXPORT_SYMBOL_GPL(ata_tf_to_fis);
/**
* ata_tf_from_fis - Convert SATA FIS to ATA taskfile
@@ -591,6 +605,7 @@ void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf)
tf->nsect = fis[12];
tf->hob_nsect = fis[13];
}
+EXPORT_SYMBOL_GPL(ata_tf_from_fis);
static const u8 ata_rw_cmds[] = {
/* pio multi */
@@ -865,6 +880,7 @@ unsigned long ata_pack_xfermask(unsigned long pio_mask,
((mwdma_mask << ATA_SHIFT_MWDMA) & ATA_MASK_MWDMA) |
((udma_mask << ATA_SHIFT_UDMA) & ATA_MASK_UDMA);
}
+EXPORT_SYMBOL_GPL(ata_pack_xfermask);
/**
* ata_unpack_xfermask - Unpack xfer_mask into pio, mwdma and udma masks
@@ -886,6 +902,7 @@ void ata_unpack_xfermask(unsigned long xfer_mask, unsigned long *pio_mask,
if (udma_mask)
*udma_mask = (xfer_mask & ATA_MASK_UDMA) >> ATA_SHIFT_UDMA;
}
+EXPORT_SYMBOL_GPL(ata_unpack_xfermask);
static const struct ata_xfer_ent {
int shift, bits;
@@ -920,6 +937,7 @@ u8 ata_xfer_mask2mode(unsigned long xfer_mask)
return ent->base + highbit - ent->shift;
return 0xff;
}
+EXPORT_SYMBOL_GPL(ata_xfer_mask2mode);
/**
* ata_xfer_mode2mask - Find matching xfer_mask for XFER_*
@@ -943,6 +961,7 @@ unsigned long ata_xfer_mode2mask(u8 xfer_mode)
& ~((1 << ent->shift) - 1);
return 0;
}
+EXPORT_SYMBOL_GPL(ata_xfer_mode2mask);
/**
* ata_xfer_mode2shift - Find matching xfer_shift for XFER_*
@@ -965,6 +984,7 @@ int ata_xfer_mode2shift(unsigned long xfer_mode)
return ent->shift;
return -1;
}
+EXPORT_SYMBOL_GPL(ata_xfer_mode2shift);
/**
* ata_mode_string - convert xfer_mask to string
@@ -1011,6 +1031,7 @@ const char *ata_mode_string(unsigned long xfer_mask)
return xfer_mode_str[highbit];
return "<n/a>";
}
+EXPORT_SYMBOL_GPL(ata_mode_string);
const char *sata_spd_string(unsigned int spd)
{
@@ -1091,6 +1112,7 @@ unsigned int ata_dev_classify(const struct ata_taskfile *tf)
DPRINTK("unknown device\n");
return ATA_DEV_UNKNOWN;
}
+EXPORT_SYMBOL_GPL(ata_dev_classify);
/**
* ata_id_string - Convert IDENTIFY DEVICE page into string
@@ -1127,6 +1149,7 @@ void ata_id_string(const u16 *id, unsigned char *s,
len -= 2;
}
}
+EXPORT_SYMBOL_GPL(ata_id_string);
/**
* ata_id_c_string - Convert IDENTIFY DEVICE page into C string
@@ -1154,6 +1177,7 @@ void ata_id_c_string(const u16 *id, unsigned char *s,
p--;
*p = '\0';
}
+EXPORT_SYMBOL_GPL(ata_id_c_string);
static u64 ata_id_n_sectors(const u16 *id)
{
@@ -1511,6 +1535,7 @@ unsigned long ata_id_xfermask(const u16 *id)
return ata_pack_xfermask(pio_mask, mwdma_mask, udma_mask);
}
+EXPORT_SYMBOL_GPL(ata_id_xfermask);
static void ata_qc_complete_internal(struct ata_queued_cmd *qc)
{
@@ -1768,6 +1793,7 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev)
return 1;
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
/**
* ata_pio_mask_no_iordy - Return the non IORDY mask
@@ -1808,6 +1834,7 @@ unsigned int ata_do_dev_read_id(struct ata_device *dev,
return ata_exec_internal(dev, tf, NULL, DMA_FROM_DEVICE,
id, sizeof(id[0]) * ATA_ID_WORDS, 0);
}
+EXPORT_SYMBOL_GPL(ata_do_dev_read_id);
/**
* ata_dev_read_id - Read ID data from the specified device
@@ -2780,6 +2807,7 @@ int ata_cable_40wire(struct ata_port *ap)
{
return ATA_CBL_PATA40;
}
+EXPORT_SYMBOL_GPL(ata_cable_40wire);
/**
* ata_cable_80wire - return 80 wire cable type
@@ -2793,6 +2821,7 @@ int ata_cable_80wire(struct ata_port *ap)
{
return ATA_CBL_PATA80;
}
+EXPORT_SYMBOL_GPL(ata_cable_80wire);
/**
* ata_cable_unknown - return unknown PATA cable.
@@ -2805,6 +2834,7 @@ int ata_cable_unknown(struct ata_port *ap)
{
return ATA_CBL_PATA_UNK;
}
+EXPORT_SYMBOL_GPL(ata_cable_unknown);
/**
* ata_cable_ignore - return ignored PATA cable.
@@ -2817,6 +2847,7 @@ int ata_cable_ignore(struct ata_port *ap)
{
return ATA_CBL_PATA_IGN;
}
+EXPORT_SYMBOL_GPL(ata_cable_ignore);
/**
* ata_cable_sata - return SATA cable type
@@ -2829,6 +2860,7 @@ int ata_cable_sata(struct ata_port *ap)
{
return ATA_CBL_SATA;
}
+EXPORT_SYMBOL_GPL(ata_cable_sata);
/**
* ata_bus_probe - Reset and probe ATA bus
@@ -3011,6 +3043,7 @@ struct ata_device *ata_dev_pair(struct ata_device *adev)
return NULL;
return pair;
}
+EXPORT_SYMBOL_GPL(ata_dev_pair);
/**
* sata_down_spd_limit - adjust SATA spd limit downward
@@ -3171,6 +3204,7 @@ int sata_set_spd(struct ata_link *link)
return 1;
}
+EXPORT_SYMBOL_GPL(sata_set_spd);
/*
* This mode timing computation functionality is ported over from
@@ -3245,6 +3279,7 @@ void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
if (what & ATA_TIMING_CYCLE ) m->cycle = max(a->cycle, b->cycle);
if (what & ATA_TIMING_UDMA ) m->udma = max(a->udma, b->udma);
}
+EXPORT_SYMBOL_GPL(ata_timing_merge);
const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
{
@@ -3261,6 +3296,7 @@ const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
return NULL;
}
+EXPORT_SYMBOL_GPL(ata_timing_find_mode);
int ata_timing_compute(struct ata_device *adev, unsigned short speed,
struct ata_timing *t, int T, int UT)
@@ -3337,6 +3373,7 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
return 0;
}
+EXPORT_SYMBOL_GPL(ata_timing_compute);
/**
* ata_timing_cycle2mode - find xfer mode for the specified cycle duration
@@ -3388,6 +3425,7 @@ u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle)
return last_mode;
}
+EXPORT_SYMBOL_GPL(ata_timing_cycle2mode);
/**
* ata_down_xfermask_limit - adjust dev xfer masks downward
@@ -3659,6 +3697,7 @@ int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev)
*r_failed_dev = dev;
return rc;
}
+EXPORT_SYMBOL_GPL(ata_do_set_mode);
/**
* ata_wait_ready - wait for link to become ready
@@ -3768,6 +3807,7 @@ int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
return ata_wait_ready(link, deadline, check_ready);
}
+EXPORT_SYMBOL_GPL(ata_wait_after_reset);
/**
* sata_link_debounce - debounce SATA phy status
@@ -3838,6 +3878,7 @@ int sata_link_debounce(struct ata_link *link, const unsigned long *params,
return -EPIPE;
}
}
+EXPORT_SYMBOL_GPL(sata_link_debounce);
/**
* sata_link_resume - resume SATA link
@@ -3904,6 +3945,7 @@ int sata_link_resume(struct ata_link *link, const unsigned long *params,
return rc != -EINVAL ? rc : 0;
}
+EXPORT_SYMBOL_GPL(sata_link_resume);
/**
* sata_link_scr_lpm - manipulate SControl IPM and SPM fields
@@ -3978,6 +4020,7 @@ int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
ehc->i.serror &= ~SERR_PHYRDY_CHG;
return sata_scr_write(link, SCR_ERROR, SERR_PHYRDY_CHG);
}
+EXPORT_SYMBOL_GPL(sata_link_scr_lpm);
/**
* ata_std_prereset - prepare for reset
@@ -4023,6 +4066,7 @@ int ata_std_prereset(struct ata_link *link, unsigned long deadline)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_std_prereset);
/**
* sata_link_hardreset - reset link via SATA phy reset
@@ -4135,6 +4179,7 @@ int sata_link_hardreset(struct ata_link *link, const unsigned long *timing,
DPRINTK("EXIT, rc=%d\n", rc);
return rc;
}
+EXPORT_SYMBOL_GPL(sata_link_hardreset);
/**
* sata_std_hardreset - COMRESET w/o waiting or classification
@@ -4161,6 +4206,7 @@ int sata_std_hardreset(struct ata_link *link, unsigned int *class,
rc = sata_link_hardreset(link, timing, deadline, &online, NULL);
return online ? -EAGAIN : rc;
}
+EXPORT_SYMBOL_GPL(sata_std_hardreset);
/**
* ata_std_postreset - standard postreset callback
@@ -4189,6 +4235,7 @@ void ata_std_postreset(struct ata_link *link, unsigned int *classes)
DPRINTK("EXIT\n");
}
+EXPORT_SYMBOL_GPL(ata_std_postreset);
/**
* ata_dev_same_device - Determine whether new ID matches configured device
@@ -4976,11 +5023,13 @@ int ata_std_qc_defer(struct ata_queued_cmd *qc)
return ATA_DEFER_LINK;
}
+EXPORT_SYMBOL_GPL(ata_std_qc_defer);
enum ata_completion_errors ata_noop_qc_prep(struct ata_queued_cmd *qc)
{
return AC_ERR_OK;
}
+EXPORT_SYMBOL_GPL(ata_noop_qc_prep);
/**
* ata_sg_init - Associate command with scatter-gather table.
@@ -5002,6 +5051,7 @@ void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
qc->n_elem = n_elem;
qc->cursg = qc->sg;
}
+EXPORT_SYMBOL_GPL(ata_sg_init);
#ifdef CONFIG_HAS_DMA
@@ -5324,6 +5374,7 @@ void ata_qc_complete(struct ata_queued_cmd *qc)
__ata_qc_complete(qc);
}
}
+EXPORT_SYMBOL_GPL(ata_qc_complete);
/**
* ata_qc_get_active - get bitmask of active qcs
@@ -5406,6 +5457,7 @@ int ata_qc_complete_multiple(struct ata_port *ap, u64 qc_active)
return nr_done;
}
+EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
/**
* ata_qc_issue - issue taskfile to device
@@ -5500,6 +5552,7 @@ int sata_scr_valid(struct ata_link *link)
return (ap->flags & ATA_FLAG_SATA) && ap->ops->scr_read;
}
+EXPORT_SYMBOL_GPL(sata_scr_valid);
/**
* sata_scr_read - read SCR register of the specified port
@@ -5527,6 +5580,7 @@ int sata_scr_read(struct ata_link *link, int reg, u32 *val)
return sata_pmp_scr_read(link, reg, val);
}
+EXPORT_SYMBOL_GPL(sata_scr_read);
/**
* sata_scr_write - write SCR register of the specified port
@@ -5554,6 +5608,7 @@ int sata_scr_write(struct ata_link *link, int reg, u32 val)
return sata_pmp_scr_write(link, reg, val);
}
+EXPORT_SYMBOL_GPL(sata_scr_write);
/**
* sata_scr_write_flush - write SCR register of the specified port and flush
@@ -5586,6 +5641,7 @@ int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
return sata_pmp_scr_write(link, reg, val);
}
+EXPORT_SYMBOL_GPL(sata_scr_write_flush);
/**
* ata_phys_link_online - test whether the given link is online
@@ -5660,6 +5716,7 @@ bool ata_link_online(struct ata_link *link)
return ata_phys_link_online(link) ||
(slave && ata_phys_link_online(slave));
}
+EXPORT_SYMBOL_GPL(ata_link_online);
/**
* ata_link_offline - test whether the given link is offline
@@ -5686,6 +5743,7 @@ bool ata_link_offline(struct ata_link *link)
return ata_phys_link_offline(link) &&
(!slave || ata_phys_link_offline(slave));
}
+EXPORT_SYMBOL_GPL(ata_link_offline);
#ifdef CONFIG_PM
static void ata_port_request_pm(struct ata_port *ap, pm_message_t mesg,
@@ -5872,6 +5930,7 @@ int ata_host_suspend(struct ata_host *host, pm_message_t mesg)
host->dev->power.power_state = mesg;
return 0;
}
+EXPORT_SYMBOL_GPL(ata_host_suspend);
/**
* ata_host_resume - resume host
@@ -5883,6 +5942,7 @@ void ata_host_resume(struct ata_host *host)
{
host->dev->power.power_state = PMSG_ON;
}
+EXPORT_SYMBOL_GPL(ata_host_resume);
#endif
const struct device_type ata_port_type = {
@@ -6097,11 +6157,13 @@ void ata_host_get(struct ata_host *host)
{
kref_get(&host->kref);
}
+EXPORT_SYMBOL_GPL(ata_host_get);
void ata_host_put(struct ata_host *host)
{
kref_put(&host->kref, ata_host_release);
}
+EXPORT_SYMBOL_GPL(ata_host_put);
/**
* ata_host_alloc - allocate and init basic ATA host resources
@@ -6175,6 +6237,7 @@ struct ata_host *ata_host_alloc(struct device *dev, int max_ports)
kfree(host);
return NULL;
}
+EXPORT_SYMBOL_GPL(ata_host_alloc);
/**
* ata_host_alloc_pinfo - alloc host and init with port_info array
@@ -6223,6 +6286,7 @@ struct ata_host *ata_host_alloc_pinfo(struct device *dev,
return host;
}
+EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);
/**
* ata_slave_link_init - initialize slave link
@@ -6285,6 +6349,7 @@ int ata_slave_link_init(struct ata_port *ap)
ap->slave_link = link;
return 0;
}
+EXPORT_SYMBOL_GPL(ata_slave_link_init);
static void ata_host_stop(struct device *gendev, void *res)
{
@@ -6433,6 +6498,7 @@ int ata_host_start(struct ata_host *host)
devres_free(start_dr);
return rc;
}
+EXPORT_SYMBOL_GPL(ata_host_start);
/**
* ata_sas_host_init - Initialize a host struct for sas (ipr, libsas)
@@ -6451,6 +6517,7 @@ void ata_host_init(struct ata_host *host, struct device *dev,
host->ops = ops;
kref_init(&host->kref);
}
+EXPORT_SYMBOL_GPL(ata_host_init);
void __ata_port_probe(struct ata_port *ap)
{
@@ -6606,6 +6673,7 @@ int ata_host_register(struct ata_host *host, struct scsi_host_template *sht)
return rc;
}
+EXPORT_SYMBOL_GPL(ata_host_register);
/**
* ata_host_activate - start host, request IRQ and register it
@@ -6668,6 +6736,7 @@ int ata_host_activate(struct ata_host *host, int irq,
return rc;
}
+EXPORT_SYMBOL_GPL(ata_host_activate);
/**
* ata_port_detach - Detach ATA port in preparation of device removal
@@ -6743,6 +6812,7 @@ void ata_host_detach(struct ata_host *host)
/* the host is dead now, dissociate ACPI */
ata_acpi_dissociate(host);
}
+EXPORT_SYMBOL_GPL(ata_host_detach);
#ifdef CONFIG_PCI
@@ -6763,6 +6833,7 @@ void ata_pci_remove_one(struct pci_dev *pdev)
ata_host_detach(host);
}
+EXPORT_SYMBOL_GPL(ata_pci_remove_one);
void ata_pci_shutdown_one(struct pci_dev *pdev)
{
@@ -6783,6 +6854,7 @@ void ata_pci_shutdown_one(struct pci_dev *pdev)
ap->ops->port_stop(ap);
}
}
+EXPORT_SYMBOL_GPL(ata_pci_shutdown_one);
/* move to PCI subsystem */
int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits)
@@ -6817,6 +6889,7 @@ int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits)
return (tmp == bits->val) ? 1 : 0;
}
+EXPORT_SYMBOL_GPL(pci_test_config_bits);
#ifdef CONFIG_PM
void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg)
@@ -6827,6 +6900,7 @@ void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg)
if (mesg.event & PM_EVENT_SLEEP)
pci_set_power_state(pdev, PCI_D3hot);
}
+EXPORT_SYMBOL_GPL(ata_pci_device_do_suspend);
int ata_pci_device_do_resume(struct pci_dev *pdev)
{
@@ -6845,6 +6919,7 @@ int ata_pci_device_do_resume(struct pci_dev *pdev)
pci_set_master(pdev);
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pci_device_do_resume);
int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
@@ -6859,6 +6934,7 @@ int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_pci_device_suspend);
int ata_pci_device_resume(struct pci_dev *pdev)
{
@@ -6870,8 +6946,8 @@ int ata_pci_device_resume(struct pci_dev *pdev)
ata_host_resume(host);
return rc;
}
+EXPORT_SYMBOL_GPL(ata_pci_device_resume);
#endif /* CONFIG_PM */
-
#endif /* CONFIG_PCI */
/**
@@ -6893,6 +6969,7 @@ int ata_platform_remove_one(struct platform_device *pdev)
return 0;
}
+EXPORT_SYMBOL_GPL(ata_platform_remove_one);
static int __init ata_parse_force_one(char **cur,
struct ata_force_ent *force_ent,
@@ -7117,6 +7194,7 @@ int ata_ratelimit(void)
{
return __ratelimit(&ratelimit);
}
+EXPORT_SYMBOL_GPL(ata_ratelimit);
/**
* ata_msleep - ATA EH owner aware msleep
@@ -7149,6 +7227,7 @@ void ata_msleep(struct ata_port *ap, unsigned int msecs)
if (owns_eh)
ata_eh_acquire(ap);
}
+EXPORT_SYMBOL_GPL(ata_msleep);
/**
* ata_wait_register - wait until register value changes
@@ -7195,6 +7274,7 @@ u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val,
return tmp;
}
+EXPORT_SYMBOL_GPL(ata_wait_register);
/**
* sata_lpm_ignore_phy_events - test if PHY event should be ignored
@@ -7248,10 +7328,12 @@ struct ata_port_operations ata_dummy_port_ops = {
.sched_eh = ata_std_sched_eh,
.end_eh = ata_std_end_eh,
};
+EXPORT_SYMBOL_GPL(ata_dummy_port_ops);
const struct ata_port_info ata_dummy_port_info = {
.port_ops = &ata_dummy_port_ops,
};
+EXPORT_SYMBOL_GPL(ata_dummy_port_info);
/*
* Utility print functions
@@ -7319,127 +7401,3 @@ void ata_print_version(const struct device *dev, const char *version)
dev_printk(KERN_DEBUG, dev, "version %s\n", version);
}
EXPORT_SYMBOL(ata_print_version);
-
-/*
- * libata is essentially a library of internal helper functions for
- * low-level ATA host controller drivers. As such, the API/ABI is
- * likely to change as new drivers are added and updated.
- * Do not depend on ABI/API stability.
- */
-EXPORT_SYMBOL_GPL(sata_deb_timing_normal);
-EXPORT_SYMBOL_GPL(sata_deb_timing_hotplug);
-EXPORT_SYMBOL_GPL(sata_deb_timing_long);
-EXPORT_SYMBOL_GPL(ata_base_port_ops);
-EXPORT_SYMBOL_GPL(sata_port_ops);
-EXPORT_SYMBOL_GPL(ata_dummy_port_ops);
-EXPORT_SYMBOL_GPL(ata_dummy_port_info);
-EXPORT_SYMBOL_GPL(ata_link_next);
-EXPORT_SYMBOL_GPL(ata_dev_next);
-EXPORT_SYMBOL_GPL(ata_std_bios_param);
-EXPORT_SYMBOL_GPL(ata_scsi_unlock_native_capacity);
-EXPORT_SYMBOL_GPL(ata_host_init);
-EXPORT_SYMBOL_GPL(ata_host_alloc);
-EXPORT_SYMBOL_GPL(ata_host_alloc_pinfo);
-EXPORT_SYMBOL_GPL(ata_slave_link_init);
-EXPORT_SYMBOL_GPL(ata_host_start);
-EXPORT_SYMBOL_GPL(ata_host_register);
-EXPORT_SYMBOL_GPL(ata_host_activate);
-EXPORT_SYMBOL_GPL(ata_host_detach);
-EXPORT_SYMBOL_GPL(ata_sg_init);
-EXPORT_SYMBOL_GPL(ata_qc_complete);
-EXPORT_SYMBOL_GPL(ata_qc_complete_multiple);
-EXPORT_SYMBOL_GPL(atapi_cmd_type);
-EXPORT_SYMBOL_GPL(ata_tf_to_fis);
-EXPORT_SYMBOL_GPL(ata_tf_from_fis);
-EXPORT_SYMBOL_GPL(ata_pack_xfermask);
-EXPORT_SYMBOL_GPL(ata_unpack_xfermask);
-EXPORT_SYMBOL_GPL(ata_xfer_mask2mode);
-EXPORT_SYMBOL_GPL(ata_xfer_mode2mask);
-EXPORT_SYMBOL_GPL(ata_xfer_mode2shift);
-EXPORT_SYMBOL_GPL(ata_mode_string);
-EXPORT_SYMBOL_GPL(ata_id_xfermask);
-EXPORT_SYMBOL_GPL(ata_do_set_mode);
-EXPORT_SYMBOL_GPL(ata_std_qc_defer);
-EXPORT_SYMBOL_GPL(ata_noop_qc_prep);
-EXPORT_SYMBOL_GPL(ata_dev_disable);
-EXPORT_SYMBOL_GPL(sata_set_spd);
-EXPORT_SYMBOL_GPL(ata_wait_after_reset);
-EXPORT_SYMBOL_GPL(sata_link_debounce);
-EXPORT_SYMBOL_GPL(sata_link_resume);
-EXPORT_SYMBOL_GPL(sata_link_scr_lpm);
-EXPORT_SYMBOL_GPL(ata_std_prereset);
-EXPORT_SYMBOL_GPL(sata_link_hardreset);
-EXPORT_SYMBOL_GPL(sata_std_hardreset);
-EXPORT_SYMBOL_GPL(ata_std_postreset);
-EXPORT_SYMBOL_GPL(ata_dev_classify);
-EXPORT_SYMBOL_GPL(ata_dev_pair);
-EXPORT_SYMBOL_GPL(ata_ratelimit);
-EXPORT_SYMBOL_GPL(ata_msleep);
-EXPORT_SYMBOL_GPL(ata_wait_register);
-EXPORT_SYMBOL_GPL(ata_scsi_queuecmd);
-EXPORT_SYMBOL_GPL(ata_scsi_slave_config);
-EXPORT_SYMBOL_GPL(ata_scsi_slave_destroy);
-EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
-EXPORT_SYMBOL_GPL(__ata_change_queue_depth);
-EXPORT_SYMBOL_GPL(sata_scr_valid);
-EXPORT_SYMBOL_GPL(sata_scr_read);
-EXPORT_SYMBOL_GPL(sata_scr_write);
-EXPORT_SYMBOL_GPL(sata_scr_write_flush);
-EXPORT_SYMBOL_GPL(ata_link_online);
-EXPORT_SYMBOL_GPL(ata_link_offline);
-#ifdef CONFIG_PM
-EXPORT_SYMBOL_GPL(ata_host_suspend);
-EXPORT_SYMBOL_GPL(ata_host_resume);
-#endif /* CONFIG_PM */
-EXPORT_SYMBOL_GPL(ata_id_string);
-EXPORT_SYMBOL_GPL(ata_id_c_string);
-EXPORT_SYMBOL_GPL(ata_do_dev_read_id);
-EXPORT_SYMBOL_GPL(ata_scsi_simulate);
-
-EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
-EXPORT_SYMBOL_GPL(ata_timing_find_mode);
-EXPORT_SYMBOL_GPL(ata_timing_compute);
-EXPORT_SYMBOL_GPL(ata_timing_merge);
-EXPORT_SYMBOL_GPL(ata_timing_cycle2mode);
-
-#ifdef CONFIG_PCI
-EXPORT_SYMBOL_GPL(pci_test_config_bits);
-EXPORT_SYMBOL_GPL(ata_pci_shutdown_one);
-EXPORT_SYMBOL_GPL(ata_pci_remove_one);
-#ifdef CONFIG_PM
-EXPORT_SYMBOL_GPL(ata_pci_device_do_suspend);
-EXPORT_SYMBOL_GPL(ata_pci_device_do_resume);
-EXPORT_SYMBOL_GPL(ata_pci_device_suspend);
-EXPORT_SYMBOL_GPL(ata_pci_device_resume);
-#endif /* CONFIG_PM */
-#endif /* CONFIG_PCI */
-
-EXPORT_SYMBOL_GPL(ata_platform_remove_one);
-
-EXPORT_SYMBOL_GPL(__ata_ehi_push_desc);
-EXPORT_SYMBOL_GPL(ata_ehi_push_desc);
-EXPORT_SYMBOL_GPL(ata_ehi_clear_desc);
-EXPORT_SYMBOL_GPL(ata_port_desc);
-#ifdef CONFIG_PCI
-EXPORT_SYMBOL_GPL(ata_port_pbar_desc);
-#endif /* CONFIG_PCI */
-EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
-EXPORT_SYMBOL_GPL(ata_link_abort);
-EXPORT_SYMBOL_GPL(ata_port_abort);
-EXPORT_SYMBOL_GPL(ata_port_freeze);
-EXPORT_SYMBOL_GPL(sata_async_notification);
-EXPORT_SYMBOL_GPL(ata_eh_freeze_port);
-EXPORT_SYMBOL_GPL(ata_eh_thaw_port);
-EXPORT_SYMBOL_GPL(ata_eh_qc_complete);
-EXPORT_SYMBOL_GPL(ata_eh_qc_retry);
-EXPORT_SYMBOL_GPL(ata_eh_analyze_ncq_error);
-EXPORT_SYMBOL_GPL(ata_do_eh);
-EXPORT_SYMBOL_GPL(ata_std_error_handler);
-
-EXPORT_SYMBOL_GPL(ata_cable_40wire);
-EXPORT_SYMBOL_GPL(ata_cable_80wire);
-EXPORT_SYMBOL_GPL(ata_cable_unknown);
-EXPORT_SYMBOL_GPL(ata_cable_ignore);
-EXPORT_SYMBOL_GPL(ata_cable_sata);
-EXPORT_SYMBOL_GPL(ata_host_get);
-EXPORT_SYMBOL_GPL(ata_host_put);
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 53605c8949d8..1d231cfab26f 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -180,6 +180,7 @@ void __ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...)
__ata_ehi_pushv_desc(ehi, fmt, args);
va_end(args);
}
+EXPORT_SYMBOL_GPL(__ata_ehi_push_desc);
/**
* ata_ehi_push_desc - push error description with separator
@@ -203,6 +204,7 @@ void ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...)
__ata_ehi_pushv_desc(ehi, fmt, args);
va_end(args);
}
+EXPORT_SYMBOL_GPL(ata_ehi_push_desc);
/**
* ata_ehi_clear_desc - clean error description
@@ -218,6 +220,7 @@ void ata_ehi_clear_desc(struct ata_eh_info *ehi)
ehi->desc[0] = '\0';
ehi->desc_len = 0;
}
+EXPORT_SYMBOL_GPL(ata_ehi_clear_desc);
/**
* ata_port_desc - append port description
@@ -245,9 +248,9 @@ void ata_port_desc(struct ata_port *ap, const char *fmt, ...)
__ata_ehi_pushv_desc(&ap->link.eh_info, fmt, args);
va_end(args);
}
+EXPORT_SYMBOL_GPL(ata_port_desc);
#ifdef CONFIG_PCI
-
/**
* ata_port_pbar_desc - append PCI BAR description
* @ap: target ATA port
@@ -284,7 +287,7 @@ void ata_port_pbar_desc(struct ata_port *ap, int bar, ssize_t offset,
ata_port_desc(ap, "%s 0x%llx", name,
start + (unsigned long long)offset);
}
-
+EXPORT_SYMBOL_GPL(ata_port_pbar_desc);
#endif /* CONFIG_PCI */
static int ata_lookup_timeout_table(u8 cmd)
@@ -969,6 +972,7 @@ void ata_port_schedule_eh(struct ata_port *ap)
/* see: ata_std_sched_eh, unless you know better */
ap->ops->sched_eh(ap);
}
+EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
static int ata_do_link_abort(struct ata_port *ap, struct ata_link *link)
{
@@ -1011,6 +1015,7 @@ int ata_link_abort(struct ata_link *link)
{
return ata_do_link_abort(link->ap, link);
}
+EXPORT_SYMBOL_GPL(ata_link_abort);
/**
* ata_port_abort - abort all qc's on the port
@@ -1028,6 +1033,7 @@ int ata_port_abort(struct ata_port *ap)
{
return ata_do_link_abort(ap, NULL);
}
+EXPORT_SYMBOL_GPL(ata_port_abort);
/**
* __ata_port_freeze - freeze port
@@ -1084,6 +1090,7 @@ int ata_port_freeze(struct ata_port *ap)
return nr_aborted;
}
+EXPORT_SYMBOL_GPL(ata_port_freeze);
/**
* sata_async_notification - SATA async notification handler
@@ -1157,6 +1164,7 @@ int sata_async_notification(struct ata_port *ap)
return 0;
}
}
+EXPORT_SYMBOL_GPL(sata_async_notification);
/**
* ata_eh_freeze_port - EH helper to freeze port
@@ -1178,6 +1186,7 @@ void ata_eh_freeze_port(struct ata_port *ap)
__ata_port_freeze(ap);
spin_unlock_irqrestore(ap->lock, flags);
}
+EXPORT_SYMBOL_GPL(ata_eh_freeze_port);
/**
* ata_port_thaw_port - EH helper to thaw port
@@ -1206,6 +1215,7 @@ void ata_eh_thaw_port(struct ata_port *ap)
DPRINTK("ata%u port thawed\n", ap->print_id);
}
+EXPORT_SYMBOL_GPL(ata_eh_thaw_port);
static void ata_eh_scsidone(struct scsi_cmnd *scmd)
{
@@ -1240,6 +1250,7 @@ void ata_eh_qc_complete(struct ata_queued_cmd *qc)
scmd->retries = scmd->allowed;
__ata_eh_qc_complete(qc);
}
+EXPORT_SYMBOL_GPL(ata_eh_qc_complete);
/**
* ata_eh_qc_retry - Tell midlayer to retry an ATA command after EH
@@ -1259,6 +1270,7 @@ void ata_eh_qc_retry(struct ata_queued_cmd *qc)
scmd->allowed++;
__ata_eh_qc_complete(qc);
}
+EXPORT_SYMBOL_GPL(ata_eh_qc_retry);
/**
* ata_dev_disable - disable ATA device
@@ -1285,6 +1297,7 @@ void ata_dev_disable(struct ata_device *dev)
*/
ata_ering_clear(&dev->ering);
}
+EXPORT_SYMBOL_GPL(ata_dev_disable);
/**
* ata_eh_detach_dev - detach ATA device
@@ -1727,6 +1740,7 @@ void ata_eh_analyze_ncq_error(struct ata_link *link)
ehc->i.err_mask &= ~AC_ERR_DEV;
}
+EXPORT_SYMBOL_GPL(ata_eh_analyze_ncq_error);
/**
* ata_eh_analyze_tf - analyze taskfile of a failed qc
@@ -4027,6 +4041,7 @@ void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_eh_finish(ap);
}
+EXPORT_SYMBOL_GPL(ata_do_eh);
/**
* ata_std_error_handler - standard error handler
@@ -4048,6 +4063,7 @@ void ata_std_error_handler(struct ata_port *ap)
ata_do_eh(ap, ops->prereset, ops->softreset, hardreset, ops->postreset);
}
+EXPORT_SYMBOL_GPL(ata_std_error_handler);
#ifdef CONFIG_PM
/**
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index b64b0b0dfb21..a779ea57f3ad 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -501,6 +501,7 @@ int ata_std_bios_param(struct scsi_device *sdev, struct block_device *bdev,
return 0;
}
+EXPORT_SYMBOL_GPL(ata_std_bios_param);
/**
* ata_scsi_unlock_native_capacity - unlock native capacity
@@ -530,6 +531,7 @@ void ata_scsi_unlock_native_capacity(struct scsi_device *sdev)
spin_unlock_irqrestore(ap->lock, flags);
ata_port_wait_eh(ap);
}
+EXPORT_SYMBOL_GPL(ata_scsi_unlock_native_capacity);
/**
* ata_get_identity - Handler for HDIO_GET_IDENTITY ioctl
@@ -1346,6 +1348,7 @@ int ata_scsi_slave_config(struct scsi_device *sdev)
return rc;
}
+EXPORT_SYMBOL_GPL(ata_scsi_slave_config);
/**
* ata_scsi_slave_destroy - SCSI device is about to be destroyed
@@ -1385,6 +1388,7 @@ void ata_scsi_slave_destroy(struct scsi_device *sdev)
q->dma_drain_buffer = NULL;
q->dma_drain_size = 0;
}
+EXPORT_SYMBOL_GPL(ata_scsi_slave_destroy);
/**
* __ata_change_queue_depth - helper for ata_scsi_change_queue_depth
@@ -1428,6 +1432,7 @@ int __ata_change_queue_depth(struct ata_port *ap, struct scsi_device *sdev,
return scsi_change_queue_depth(sdev, queue_depth);
}
+EXPORT_SYMBOL_GPL(__ata_change_queue_depth);
/**
* ata_scsi_change_queue_depth - SCSI callback for queue depth config
@@ -1450,6 +1455,7 @@ int ata_scsi_change_queue_depth(struct scsi_device *sdev, int queue_depth)
return __ata_change_queue_depth(ap, sdev, queue_depth);
}
+EXPORT_SYMBOL_GPL(ata_scsi_change_queue_depth);
/**
* ata_scsi_start_stop_xlat - Translate SCSI START STOP UNIT command
@@ -4405,6 +4411,7 @@ int ata_scsi_queuecmd(struct Scsi_Host *shost, struct scsi_cmnd *cmd)
return rc;
}
+EXPORT_SYMBOL_GPL(ata_scsi_queuecmd);
/**
* ata_scsi_simulate - simulate SCSI command on ATA device
@@ -4528,6 +4535,7 @@ void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd)
cmd->scsi_done(cmd);
}
+EXPORT_SYMBOL_GPL(ata_scsi_simulate);
int ata_scsi_add_hosts(struct ata_host *host, struct scsi_host_template *sht)
{
--
2.24.1
In commit 7634ccd2da97 ("libata: maintainership update") from 2018
Jens has officially taken over libata maintainership from Tejun so
remove stale information from core libata code.
Acked-by: Tejun Heo <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 4 ----
drivers/ata/libata-eh.c | 4 ----
drivers/ata/libata-scsi.c | 4 ----
drivers/ata/libata-sff.c | 4 ----
4 files changed, 16 deletions(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 42c8728f6117..4991f9d5def8 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2,10 +2,6 @@
/*
* libata-core.c - helper library for ATA
*
- * Maintained by: Tejun Heo <[email protected]>
- * Please ALWAYS copy [email protected]
- * on emails.
- *
* Copyright 2003-2004 Red Hat, Inc. All rights reserved.
* Copyright 2003-2004 Jeff Garzik
*
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 3bfd9da58473..53605c8949d8 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2,10 +2,6 @@
/*
* libata-eh.c - libata error handling
*
- * Maintained by: Tejun Heo <[email protected]>
- * Please ALWAYS copy [email protected]
- * on emails.
- *
* Copyright 2006 Tejun Heo <[email protected]>
*
* libata documentation is available via 'make {ps|pdf}docs',
diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
index eb2eb599e602..11eb25b6e2cd 100644
--- a/drivers/ata/libata-scsi.c
+++ b/drivers/ata/libata-scsi.c
@@ -2,10 +2,6 @@
/*
* libata-scsi.c - helper library for ATA
*
- * Maintained by: Tejun Heo <[email protected]>
- * Please ALWAYS copy [email protected]
- * on emails.
- *
* Copyright 2003-2004 Red Hat, Inc. All rights reserved.
* Copyright 2003-2004 Jeff Garzik
*
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 038db94216a9..ae7189d1a568 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -2,10 +2,6 @@
/*
* libata-sff.c - helper library for PCI IDE BMDMA
*
- * Maintained by: Tejun Heo <[email protected]>
- * Please ALWAYS copy [email protected]
- * on emails.
- *
* Copyright 2003-2006 Red Hat, Inc. All rights reserved.
* Copyright 2003-2006 Jeff Garzik
*
--
2.24.1
There is no reason to expose SATA_PMP config option when no SATA
host drivers are enabled. To fix it add SATA_HOST config option,
make all SATA host drivers select it and finally make SATA_PMP
config options depend on it.
This also serves as preparation for the future changes which
optimize libata core code size on PATA only setups.
CC: "James E.J. Bottomley" <[email protected]>
Reviewed-by: Martin K. Petersen <[email protected]> # for SCSI bits
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/Kconfig | 40 +++++++++++++++++++++++++++++++++++++
drivers/scsi/Kconfig | 1 +
drivers/scsi/libsas/Kconfig | 1 +
3 files changed, 42 insertions(+)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index a6beb2c5a692..ad7760656f71 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -34,6 +34,9 @@ if ATA
config ATA_NONSTANDARD
bool
+config SATA_HOST
+ bool
+
config ATA_VERBOSE_ERROR
bool "Verbose ATA error reporting"
default y
@@ -73,6 +76,7 @@ config SATA_ZPODD
config SATA_PMP
bool "SATA Port Multiplier support"
+ depends on SATA_HOST
default y
help
This option adds support for SATA Port Multipliers
@@ -85,6 +89,7 @@ comment "Controllers with non-SFF native interface"
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for AHCI Serial ATA.
@@ -111,6 +116,7 @@ config SATA_MOBILE_LPM_POLICY
config SATA_AHCI_PLATFORM
tristate "Platform AHCI SATA support"
+ select SATA_HOST
help
This option enables support for Platform AHCI Serial ATA
controllers.
@@ -121,6 +127,7 @@ config AHCI_BRCM
tristate "Broadcom AHCI SATA support"
depends on ARCH_BRCMSTB || BMIPS_GENERIC || ARCH_BCM_NSP || \
ARCH_BCM_63XX
+ select SATA_HOST
help
This option enables support for the AHCI SATA3 controller found on
Broadcom SoC's.
@@ -130,6 +137,7 @@ config AHCI_BRCM
config AHCI_DA850
tristate "DaVinci DA850 AHCI SATA support"
depends on ARCH_DAVINCI_DA850
+ select SATA_HOST
help
This option enables support for the DaVinci DA850 SoC's
onboard AHCI SATA.
@@ -139,6 +147,7 @@ config AHCI_DA850
config AHCI_DM816
tristate "DaVinci DM816 AHCI SATA support"
depends on ARCH_OMAP2PLUS
+ select SATA_HOST
help
This option enables support for the DaVinci DM816 SoC's
onboard AHCI SATA controller.
@@ -148,6 +157,7 @@ config AHCI_DM816
config AHCI_ST
tristate "ST AHCI SATA support"
depends on ARCH_STI
+ select SATA_HOST
help
This option enables support for ST AHCI SATA controller.
@@ -157,6 +167,7 @@ config AHCI_IMX
tristate "Freescale i.MX AHCI SATA support"
depends on MFD_SYSCON && (ARCH_MXC || COMPILE_TEST)
depends on (HWMON && (THERMAL || !THERMAL_OF)) || !HWMON
+ select SATA_HOST
help
This option enables support for the Freescale i.MX SoC's
onboard AHCI SATA.
@@ -166,6 +177,7 @@ config AHCI_IMX
config AHCI_CEVA
tristate "CEVA AHCI SATA support"
depends on OF
+ select SATA_HOST
help
This option enables support for the CEVA AHCI SATA.
It can be found on the Xilinx Zynq UltraScale+ MPSoC.
@@ -176,6 +188,7 @@ config AHCI_MTK
tristate "MediaTek AHCI SATA support"
depends on ARCH_MEDIATEK
select MFD_SYSCON
+ select SATA_HOST
help
This option enables support for the MediaTek SoC's
onboard AHCI SATA controller.
@@ -185,6 +198,7 @@ config AHCI_MTK
config AHCI_MVEBU
tristate "Marvell EBU AHCI SATA support"
depends on ARCH_MVEBU
+ select SATA_HOST
help
This option enables support for the Marvebu EBU SoC's
onboard AHCI SATA.
@@ -203,6 +217,7 @@ config AHCI_OCTEON
config AHCI_SUNXI
tristate "Allwinner sunxi AHCI SATA support"
depends on ARCH_SUNXI
+ select SATA_HOST
help
This option enables support for the Allwinner sunxi SoC's
onboard AHCI SATA.
@@ -212,6 +227,7 @@ config AHCI_SUNXI
config AHCI_TEGRA
tristate "NVIDIA Tegra AHCI SATA support"
depends on ARCH_TEGRA
+ select SATA_HOST
help
This option enables support for the NVIDIA Tegra SoC's
onboard AHCI SATA.
@@ -221,12 +237,14 @@ config AHCI_TEGRA
config AHCI_XGENE
tristate "APM X-Gene 6.0Gbps AHCI SATA host controller support"
depends on PHY_XGENE
+ select SATA_HOST
help
This option enables support for APM X-Gene SoC SATA host controller.
config AHCI_QORIQ
tristate "Freescale QorIQ AHCI SATA support"
depends on OF
+ select SATA_HOST
help
This option enables support for the Freescale QorIQ AHCI SoC's
onboard AHCI SATA.
@@ -236,6 +254,7 @@ config AHCI_QORIQ
config SATA_FSL
tristate "Freescale 3.0Gbps SATA support"
depends on FSL_SOC
+ select SATA_HOST
help
This option enables support for Freescale 3.0Gbps SATA controller.
It can be found on MPC837x and MPC8315.
@@ -245,6 +264,7 @@ config SATA_FSL
config SATA_GEMINI
tristate "Gemini SATA bridge support"
depends on ARCH_GEMINI || COMPILE_TEST
+ select SATA_HOST
default ARCH_GEMINI
help
This enabled support for the FTIDE010 to SATA bridge
@@ -255,6 +275,7 @@ config SATA_GEMINI
config SATA_AHCI_SEATTLE
tristate "AMD Seattle 6.0Gbps AHCI SATA host controller support"
depends on ARCH_SEATTLE
+ select SATA_HOST
help
This option enables support for AMD Seattle SATA host controller.
@@ -263,12 +284,14 @@ config SATA_AHCI_SEATTLE
config SATA_INIC162X
tristate "Initio 162x SATA support (Very Experimental)"
depends on PCI
+ select SATA_HOST
help
This option enables support for Initio 162x Serial ATA.
config SATA_ACARD_AHCI
tristate "ACard AHCI variant (ATP 8620)"
depends on PCI
+ select SATA_HOST
help
This option enables support for Acard.
@@ -277,6 +300,7 @@ config SATA_ACARD_AHCI
config SATA_SIL24
tristate "Silicon Image 3124/3132 SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Silicon Image 3124/3132 Serial ATA.
@@ -326,6 +350,7 @@ config PATA_OCTEON_CF
config SATA_QSTOR
tristate "Pacific Digital SATA QStor support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Pacific Digital Serial ATA QStor.
@@ -334,6 +359,7 @@ config SATA_QSTOR
config SATA_SX4
tristate "Promise SATA SX4 support (Experimental)"
depends on PCI
+ select SATA_HOST
help
This option enables support for Promise Serial ATA SX4.
@@ -357,6 +383,7 @@ comment "SATA SFF controllers with BMDMA"
config ATA_PIIX
tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for ICH5/6/7/8 Serial ATA
and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series
@@ -368,6 +395,7 @@ config SATA_DWC
tristate "DesignWare Cores SATA support"
depends on DMADEVICES
select GENERIC_PHY
+ select SATA_HOST
help
This option enables support for the on-chip SATA controller of the
AppliedMicro processor 460EX.
@@ -398,6 +426,7 @@ config SATA_DWC_VDEBUG
config SATA_HIGHBANK
tristate "Calxeda Highbank SATA support"
depends on ARCH_HIGHBANK || COMPILE_TEST
+ select SATA_HOST
help
This option enables support for the Calxeda Highbank SoC's
onboard SATA.
@@ -409,6 +438,7 @@ config SATA_MV
depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST
select GENERIC_PHY
+ select SATA_HOST
help
This option enables support for the Marvell Serial ATA family.
Currently supports 88SX[56]0[48][01] PCI(-X) chips,
@@ -419,6 +449,7 @@ config SATA_MV
config SATA_NV
tristate "NVIDIA SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for NVIDIA Serial ATA.
@@ -427,6 +458,7 @@ config SATA_NV
config SATA_PROMISE
tristate "Promise SATA TX2/TX4 support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Promise Serial ATA TX2/TX4.
@@ -435,6 +467,7 @@ config SATA_PROMISE
config SATA_RCAR
tristate "Renesas R-Car SATA support"
depends on ARCH_RENESAS || COMPILE_TEST
+ select SATA_HOST
help
This option enables support for Renesas R-Car Serial ATA.
@@ -443,6 +476,7 @@ config SATA_RCAR
config SATA_SIL
tristate "Silicon Image SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Silicon Image Serial ATA.
@@ -452,6 +486,7 @@ config SATA_SIS
tristate "SiS 964/965/966/180 SATA support"
depends on PCI
select PATA_SIS
+ select SATA_HOST
help
This option enables support for SiS Serial ATA on
SiS 964/965/966/180 and Parallel ATA on SiS 180.
@@ -462,6 +497,7 @@ config SATA_SIS
config SATA_SVW
tristate "ServerWorks Frodo / Apple K2 SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Broadcom/Serverworks/Apple K2
SATA support.
@@ -471,6 +507,7 @@ config SATA_SVW
config SATA_ULI
tristate "ULi Electronics SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for ULi Electronics SATA.
@@ -479,6 +516,7 @@ config SATA_ULI
config SATA_VIA
tristate "VIA SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for VIA Serial ATA.
@@ -487,6 +525,7 @@ config SATA_VIA
config SATA_VITESSE
tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
depends on PCI
+ select SATA_HOST
help
This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
@@ -1113,6 +1152,7 @@ config PATA_ACPI
config ATA_GENERIC
tristate "Generic ATA support"
depends on PCI && ATA_BMDMA
+ select SATA_HOST
help
This option enables support for generic BIOS configured
ATA controllers via the new ATA layer
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 2b882b96e0d4..a790d360ceaa 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -980,6 +980,7 @@ config SCSI_SYM53C8XX_MMIO
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
depends on PCI && SCSI && ATA
+ select SATA_HOST
select FW_LOADER
select IRQ_POLL
select SGL_ALLOC
diff --git a/drivers/scsi/libsas/Kconfig b/drivers/scsi/libsas/Kconfig
index 5c6a5eff2f8e..052ee3a26f6e 100644
--- a/drivers/scsi/libsas/Kconfig
+++ b/drivers/scsi/libsas/Kconfig
@@ -19,6 +19,7 @@ config SCSI_SAS_ATA
bool "ATA support for libsas (requires libata)"
depends on SCSI_SAS_LIBSAS
depends on ATA = y || ATA = SCSI_SAS_LIBSAS
+ select SATA_HOST
help
Builds in ATA support into libsas. Will necessitate
the loading of libata along with libsas.
--
2.24.1
Use COMMAND_LINE_SIZE instead PAGE_SIZE for ata_force_param_buf[]
size as libata parameters buffer doesn't need to be bigger than
the command line buffer.
For many architectures this results in decreased libata-core.o
size (COMMAND_LINE_SIZE varies from 256 to 4096 while the minimum
PAGE_SIZE is 4096).
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
41064 4413 40 45517 b1cd drivers/ata/libata-core.o
after:
41064 573 40 41677 a2cd drivers/ata/libata-core.o
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]>
---
drivers/ata/libata-core.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 4991f9d5def8..a9a8762448aa 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -52,6 +52,7 @@
#include <linux/leds.h>
#include <linux/pm_runtime.h>
#include <linux/platform_device.h>
+#include <asm/setup.h>
#define CREATE_TRACE_POINTS
#include <trace/events/libata.h>
@@ -106,7 +107,7 @@ struct ata_force_ent {
static struct ata_force_ent *ata_force_tbl;
static int ata_force_tbl_size;
-static char ata_force_param_buf[PAGE_SIZE] __initdata;
+static char ata_force_param_buf[COMMAND_LINE_SIZE] __initdata;
/* param_buf is thrown away after initialization, disallow read */
module_param_string(force, ata_force_param_buf, sizeof(ata_force_param_buf), 0);
MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link speed and transfer mode (see Documentation/admin-guide/kernel-parameters.rst for details)");
--
2.24.1
On 2/27/20 11:21 AM, Bartlomiej Zolnierkiewicz wrote:
> Hi,
>
> There have been reports in the past of libata core code size
> being a problem in migration from deprecated IDE subsystem on
> legacy PATA only systems, i.e.:
>
> https://lore.kernel.org/linux-ide/[email protected]/
>
> This patchset re-organizes libata core code to exclude SATA
> specific code from being built for PATA only setups.
>
> The end result is up to 24% (by 23949 bytes, from 101769 bytes to
> 77820 bytes) smaller libata core code size (as measured for m68k
> arch using modified atari_defconfig) on affected setups.
>
> I've tested this patchset using pata_falcon driver under ARAnyM
> emulator.
>
>
> patches #1-11 are general fixes/cleanups done in the process of
> making the patchset (there should be no inter-dependencies between
> them except patch #10 which depends on patch #9)
>
> patch #12 separates PATA timings code to libata-pata-timings.c file
>
> patches #13-15 let compiler optimize out SATA specific code on
> non-SATA hosts by adding !IS_ENABLED(CONFIG_SATA_HOST) instances
>
> patches #16-22 separate SATA only code from libata-core.c file to
> libata-sata.c one
>
> patches #23-24 separate SATA only code from libata-scsi.c file to
> libata-sata.c one
>
> patches #25-26 separate SATA only code from libata-eh.c file to
> libata-sata.c one
>
> patch #27 makes "libata.force" kernel parameter optional
Bart, patch #2 seemed to have an issue, are you going to resend
this patchset?
--
Jens Axboe