LinuxLists.cc - [PATCH 2/2] ARM: dts: sun4i: Add support for Topwise A721 tablet

2020-03-10 11:11:34

Subject: [PATCH 2/2] ARM: dts: sun4i: Add support for Topwise A721 tablet

The Topwise A721/LY-F1 tablet is a tablet sold around 2012 under
different brands. The mainboard mentions A721 clearly, so this tablet
is best known under this name.

Signed-off-by: Pascal Roeleven <[email protected]>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun4i-a10-topwise-a721.dts | 302 +++++++++++++++++++
2 files changed, 304 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun4i-a10-topwise-a721.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 78f144e33..6e6141e00 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1040,7 +1040,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-olinuxino-lime.dtb \
sun4i-a10-pcduino.dtb \
sun4i-a10-pcduino2.dtb \
- sun4i-a10-pov-protab2-ips9.dtb
+ sun4i-a10-pov-protab2-ips9.dtb \
+ sun4i-a10-topwise-a721.dtb
dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a10s-auxtek-t003.dtb \
sun5i-a10s-auxtek-t004.dtb \
diff --git a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
new file mode 100644
index 000000000..ff43c9c12
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
@@ -0,0 +1,302 @@
+/*
+ * Copyright 2020 Pascal Roeleven <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Topwise A721";
+ compatible = "topwise,a721", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
+ power-supply = <&reg_vbat>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ panel: panel {
+ compatible = "starry,kr070pe2t";
+ backlight = <&backlight>;
+ power-supply = <&reg_lcd_power>;
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+
+ reg_lcd_power: reg-lcd-power {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_power_pin>;
+ regulator-name = "reg-lcd-power";
+ gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ enable-active-high;
+ };
+
+ reg_vbat: reg-vbat {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ mma7660: accelerometer@4c {
+ compatible = "fsl,mma7660";
+ reg = <0x4c>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ ft5406ee8: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ vcc-supply = <&reg_vcc3v3>;
+ };
+};
+
+&lradc {
+ vref-supply = <&reg_ldo2>;
+ status = "okay";
+
+ button-vol-down {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <761904>;
+ };
+
+ button-vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <571428>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ vcc-pb-supply = <&reg_vcc3v3>;
+ vcc-pf-supply = <&reg_vcc3v3>;
+ vcc-ph-supply = <&reg_vcc3v3>;
+
+ lcd_power_pin: lcd-power-pin {
+ pins = "PH8";
+ function = "gpio_out";
+ bias-pull-up;
+ };
+
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ usb0_vbus_detect_pin: usb0-vbus-detect-pin {
+ pins = "PH5";
+ function = "gpio_in";
+ bias-pull-down;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-int-dll";
+};
+
+
+&reg_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+ status = "okay";
+};
+
+&reg_usb1_vbus {
+ status = "okay";
+};
+
+&reg_usb2_vbus {
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <&reg_usb0_vbus>;
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ usb2_vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+};
--
2.20.1

2020-03-10 14:05:32

by Ondřej Jirman

[permalink] [raw]

Subject: Re: [linux-sunxi] [PATCH 2/2] ARM: dts: sun4i: Add support for Topwise A721 tablet

Hello Pascal,

On Tue, Mar 10, 2020 at 11:27:24AM +0100, Pascal Roeleven wrote:
> The Topwise A721/LY-F1 tablet is a tablet sold around 2012 under
> different brands. The mainboard mentions A721 clearly, so this tablet
> is best known under this name.
>
> Signed-off-by: Pascal Roeleven <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/sun4i-a10-topwise-a721.dts | 302 +++++++++++++++++++
> 2 files changed, 304 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 78f144e33..6e6141e00 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1040,7 +1040,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \
> sun4i-a10-olinuxino-lime.dtb \
> sun4i-a10-pcduino.dtb \
> sun4i-a10-pcduino2.dtb \
> - sun4i-a10-pov-protab2-ips9.dtb
> + sun4i-a10-pov-protab2-ips9.dtb \
> + sun4i-a10-topwise-a721.dtb
> dtb-$(CONFIG_MACH_SUN5I) += \
> sun5i-a10s-auxtek-t003.dtb \
> sun5i-a10s-auxtek-t004.dtb \
> diff --git a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
> new file mode 100644
> index 000000000..ff43c9c12
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
> @@ -0,0 +1,302 @@
> +/*
> + * Copyright 2020 Pascal Roeleven <[email protected]>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */

You should use SPDX license identifier instead of boilerplate license
text.

> +/dts-v1/;
> +#include "sun4i-a10.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Topwise A721";
> + compatible = "topwise,a721", "allwinner,sun4i-a10";

topwise is not in vendor-prefixes.yaml

> + aliases {
> + serial0 = &uart0;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
> + power-supply = <&reg_vbat>;
> + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
> + brightness-levels = <0 30 40 50 60 70 80 90 100>;
> + default-brightness-level = <8>;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + panel: panel {
> + compatible = "starry,kr070pe2t";
> + backlight = <&backlight>;
> + power-supply = <&reg_lcd_power>;
> +
> + port {
> + panel_input: endpoint {
> + remote-endpoint = <&tcon0_out_panel>;
> + };
> + };
> + };
> +
> + reg_lcd_power: reg-lcd-power {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_power_pin>;
> + regulator-name = "reg-lcd-power";
> + gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> + enable-active-high;
> + };
> +
> + reg_vbat: reg-vbat {
> + compatible = "regulator-fixed";
> + regulator-name = "vbat";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> + };
> +
> +};
> +
> +&codec {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + axp209: pmic@34 {
> + reg = <0x34>;
> + interrupts = <0>;
> + };
> +};
> +
> +#include "axp209.dtsi"
> +
> +&ac_power_supply {
> + status = "okay";
> +};
> +
> +&battery_power_supply {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +
> + mma7660: accelerometer@4c {
> + compatible = "fsl,mma7660";
> + reg = <0x4c>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +
> + ft5406ee8: touchscreen@38 {
> + compatible = "edt,edt-ft5406";
> + reg = <0x38>;
> + interrupt-parent = <&pio>;
> + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
> + touchscreen-size-x = <800>;
> + touchscreen-size-y = <480>;
> + vcc-supply = <&reg_vcc3v3>;
> + };
> +};
> +
> +&lradc {
> + vref-supply = <&reg_ldo2>;
> + status = "okay";
> +
> + button-vol-down {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + channel = <0>;
> + voltage = <761904>;
> + };
> +
> + button-vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + channel = <0>;
> + voltage = <571428>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <&reg_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pb-supply = <&reg_vcc3v3>;
> + vcc-pf-supply = <&reg_vcc3v3>;
> + vcc-ph-supply = <&reg_vcc3v3>;
> +
> + lcd_power_pin: lcd-power-pin {
> + pins = "PH8";
> + function = "gpio_out";
> + bias-pull-up;
> + };
> +
> + usb0_id_detect_pin: usb0-id-detect-pin {
> + pins = "PH4";
> + function = "gpio_in";
> + bias-pull-up;
> + };
> +
> + usb0_vbus_detect_pin: usb0-vbus-detect-pin {
> + pins = "PH5";
> + function = "gpio_in";
> + bias-pull-down;
> + };

All 3 nodes above can be replaced with appropriate GPIO_PULL_UP / GPIO_PULL_DOWN
macros inside the *-gpios property.

> +};
> +
> +&pwm {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm0_pin>;
> + status = "okay";
> +};
> +
> +&reg_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1250000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +

You have extra space here ^

> +&reg_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +&reg_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +&reg_usb0_vbus {
> + status = "okay";
> +};
> +
> +&reg_usb1_vbus {
> + status = "okay";
> +};
> +
> +&reg_usb2_vbus {
> + status = "okay";
> +};
> +
> +&tcon0_out {
> + tcon0_out_panel: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&panel_input>;
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pb_pins>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb_power_supply {
> + status = "okay";
> +};
> +
> +&usbphy {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;

No need to use pinctrl to configure regular GPIO functions anymore.

regards,
Ondrej

> + usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> + usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
> + usb0_vbus-supply = <&reg_usb0_vbus>;
> + usb1_vbus-supply = <&reg_usb1_vbus>;
> + usb2_vbus-supply = <&reg_usb2_vbus>;
> + status = "okay";
> +};
> --
> 2.20.1
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20200310102725.14591-3-dev%40pascalroeleven.nl.

2020-03-10 14:08:57

by Ondřej Jirman

[permalink] [raw]

Subject: Re: [linux-sunxi] [PATCH 2/2] ARM: dts: sun4i: Add support for Topwise A721 tablet

On Tue, Mar 10, 2020 at 11:27:24AM +0100, Pascal Roeleven wrote:
> The Topwise A721/LY-F1 tablet is a tablet sold around 2012 under
> different brands. The mainboard mentions A721 clearly, so this tablet
> is best known under this name.
>
> Signed-off-by: Pascal Roeleven <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/sun4i-a10-topwise-a721.dts | 302 +++++++++++++++++++
> 2 files changed, 304 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>
> +/dts-v1/;
> +#include "sun4i-a10.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Topwise A721";
> + compatible = "topwise,a721", "allwinner,sun4i-a10";

And you also need to add the compatible to:

Documentation/devicetree/bindings/arm/sunxi.yaml

regards,
o.

2020-03-11 10:12:09

by Pascal Roeleven

[permalink] [raw]

Subject: Re: [linux-sunxi] [PATCH 2/2] ARM: dts: sun4i: Add support for Topwise A721 tablet

On 2020-03-10 15:02, Ondřej Jirman wrote:
> Hello Pascal,
>
> On Tue, Mar 10, 2020 at 11:27:24AM +0100, Pascal Roeleven wrote:
>> The Topwise A721/LY-F1 tablet is a tablet sold around 2012 under
>> different brands. The mainboard mentions A721 clearly, so this tablet
>> is best known under this name.
>>
>> Signed-off-by: Pascal Roeleven <[email protected]>
>> ---
>> arch/arm/boot/dts/Makefile | 3 +-
>> arch/arm/boot/dts/sun4i-a10-topwise-a721.dts | 302
>> +++++++++++++++++++
>> 2 files changed, 304 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 78f144e33..6e6141e00 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -1040,7 +1040,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \
>> sun4i-a10-olinuxino-lime.dtb \
>> sun4i-a10-pcduino.dtb \
>> sun4i-a10-pcduino2.dtb \
>> - sun4i-a10-pov-protab2-ips9.dtb
>> + sun4i-a10-pov-protab2-ips9.dtb \
>> + sun4i-a10-topwise-a721.dtb
>> dtb-$(CONFIG_MACH_SUN5I) += \
>> sun5i-a10s-auxtek-t003.dtb \
>> sun5i-a10s-auxtek-t004.dtb \
>> diff --git a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>> b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>> new file mode 100644
>> index 000000000..ff43c9c12
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
>> @@ -0,0 +1,302 @@
>> +/*
>> + * Copyright 2020 Pascal Roeleven <[email protected]>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the
>> Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
>> KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
>> WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>
> You should use SPDX license identifier instead of boilerplate license
> text.
>
>> +/dts-v1/;
>> +#include "sun4i-a10.dtsi"
>> +#include "sunxi-common-regulators.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/pwm/pwm.h>
>> +
>> +/ {
>> + model = "Topwise A721";
>> + compatible = "topwise,a721", "allwinner,sun4i-a10";
>
> topwise is not in vendor-prefixes.yaml
>
>> + aliases {
>> + serial0 = &uart0;
>> + };
>> +
>> + backlight: backlight {
>> + compatible = "pwm-backlight";
>> + pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>;
>> + power-supply = <&reg_vbat>;
>> + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
>> + brightness-levels = <0 30 40 50 60 70 80 90 100>;
>> + default-brightness-level = <8>;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + panel: panel {
>> + compatible = "starry,kr070pe2t";
>> + backlight = <&backlight>;
>> + power-supply = <&reg_lcd_power>;
>> +
>> + port {
>> + panel_input: endpoint {
>> + remote-endpoint = <&tcon0_out_panel>;
>> + };
>> + };
>> + };
>> +
>> + reg_lcd_power: reg-lcd-power {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&lcd_power_pin>;
>> + regulator-name = "reg-lcd-power";
>> + gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
>> + enable-active-high;
>> + };
>> +
>> + reg_vbat: reg-vbat {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vbat";
>> + regulator-min-microvolt = <3700000>;
>> + regulator-max-microvolt = <3700000>;
>> + };
>> +
>> +};
>> +
>> +&codec {
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <&reg_dcdc2>;
>> +};
>> +
>> +&de {
>> + status = "okay";
>> +};
>> +
>> +&ehci0 {
>> + status = "okay";
>> +};
>> +
>> +&ehci1 {
>> + status = "okay";
>> +};
>> +
>> +&i2c0 {
>> + status = "okay";
>> +
>> + axp209: pmic@34 {
>> + reg = <0x34>;
>> + interrupts = <0>;
>> + };
>> +};
>> +
>> +#include "axp209.dtsi"
>> +
>> +&ac_power_supply {
>> + status = "okay";
>> +};
>> +
>> +&battery_power_supply {
>> + status = "okay";
>> +};
>> +
>> +&i2c1 {
>> + status = "okay";
>> +
>> + mma7660: accelerometer@4c {
>> + compatible = "fsl,mma7660";
>> + reg = <0x4c>;
>> + };
>> +};
>> +
>> +&i2c2 {
>> + status = "okay";
>> +
>> + ft5406ee8: touchscreen@38 {
>> + compatible = "edt,edt-ft5406";
>> + reg = <0x38>;
>> + interrupt-parent = <&pio>;
>> + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
>> + touchscreen-size-x = <800>;
>> + touchscreen-size-y = <480>;
>> + vcc-supply = <&reg_vcc3v3>;
>> + };
>> +};
>> +
>> +&lradc {
>> + vref-supply = <&reg_ldo2>;
>> + status = "okay";
>> +
>> + button-vol-down {
>> + label = "Volume Down";
>> + linux,code = <KEY_VOLUMEDOWN>;
>> + channel = <0>;
>> + voltage = <761904>;
>> + };
>> +
>> + button-vol-up {
>> + label = "Volume Up";
>> + linux,code = <KEY_VOLUMEUP>;
>> + channel = <0>;
>> + voltage = <571428>;
>> + };
>> +};
>> +
>> +&mmc0 {
>> + vmmc-supply = <&reg_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */
>> + status = "okay";
>> +};
>> +
>> +&ohci0 {
>> + status = "okay";
>> +};
>> +
>> +&ohci1 {
>> + status = "okay";
>> +};
>> +
>> +&otg_sram {
>> + status = "okay";
>> +};
>> +
>> +&pio {
>> + vcc-pb-supply = <&reg_vcc3v3>;
>> + vcc-pf-supply = <&reg_vcc3v3>;
>> + vcc-ph-supply = <&reg_vcc3v3>;
>> +
>> + lcd_power_pin: lcd-power-pin {
>> + pins = "PH8";
>> + function = "gpio_out";
>> + bias-pull-up;
>> + };
>> +
>> + usb0_id_detect_pin: usb0-id-detect-pin {
>> + pins = "PH4";
>> + function = "gpio_in";
>> + bias-pull-up;
>> + };
>> +
>> + usb0_vbus_detect_pin: usb0-vbus-detect-pin {
>> + pins = "PH5";
>> + function = "gpio_in";
>> + bias-pull-down;
>> + };
>
> All 3 nodes above can be replaced with appropriate GPIO_PULL_UP /
> GPIO_PULL_DOWN
> macros inside the *-gpios property.
>
>> +};
>> +
>> +&pwm {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pwm0_pin>;
>> + status = "okay";
>> +};
>> +
>> +&reg_dcdc2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-cpu";
>> +};
>> +
>> +&reg_dcdc3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1250000>;
>> + regulator-max-microvolt = <1250000>;
>> + regulator-name = "vdd-int-dll";
>> +};
>> +
>> +
>
> You have extra space here ^
>
>> +&reg_ldo1 {
>> + regulator-name = "vdd-rtc";
>> +};
>> +
>> +&reg_ldo2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-name = "avcc";
>> +};
>> +
>> +&reg_usb0_vbus {
>> + status = "okay";
>> +};
>> +
>> +&reg_usb1_vbus {
>> + status = "okay";
>> +};
>> +
>> +&reg_usb2_vbus {
>> + status = "okay";
>> +};
>> +
>> +&tcon0_out {
>> + tcon0_out_panel: endpoint@0 {
>> + reg = <0>;
>> + remote-endpoint = <&panel_input>;
>> + };
>> +};
>> +
>> +&uart0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart0_pb_pins>;
>> + status = "okay";
>> +};
>> +
>> +&usb_otg {
>> + dr_mode = "otg";
>> + status = "okay";
>> +};
>> +
>> +&usb_power_supply {
>> + status = "okay";
>> +};
>> +
>> +&usbphy {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
>
> No need to use pinctrl to configure regular GPIO functions anymore.
>
> regards,
> Ondrej
>
>> + usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
>> + usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
>> + usb0_vbus-supply = <&reg_usb0_vbus>;
>> + usb1_vbus-supply = <&reg_usb1_vbus>;
>> + usb2_vbus-supply = <&reg_usb2_vbus>;
>> + status = "okay";
>> +};
>> --
>> 2.20.1
>>
>> --
>> You received this message because you are subscribed to the Google
>> Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it, send
>> an email to [email protected].
>> To view this discussion on the web, visit
>> https://groups.google.com/d/msgid/linux-sunxi/20200310102725.14591-3-dev%40pascalroeleven.nl.

Hi Ondrej,

Thank you for your review. I will be fixing these in v2.